| Age | Commit message (Expand) | Author |
|---|
| 2000-01-01 | Set output on for wide-PW cal of wide-PW models, because terminations can loa...HEADINSTRUMENT_6_4_39master | Mike |
| 2000-01-01 | revert support of 3-pin keypad alarm configuration, but keep streamlined codeINSTRUMENT_6_4_38b | Mike |
| 2000-01-01 | ignore jig alarm input on older keypads with 3 alarm inputsINSTRUMENT_6_4_38 | Mike |
| 2000-01-01 | Disable frequency-related error checking if not in internal modeINSTRUMENT_6_4_37 | Mike |
| 2000-01-01 | report max change in cal correctly, by comparing using fabs on both sidesINSTRUMENT_6_4_36 | Mike |
| 2000-01-01 | make sure PW shift tweak works in 156E, fixes change from 6.4.29 aimed at AVP...INSTRUMENT_6_4_35 | Mike |
| 2000-01-01 | set distort dac to mid-range while calibrating OS, for 1041 offset nullingINSTRUMENT_6_4_34 | Mike |
| 2000-01-01 | Sleep time is now fraction of max based on DAC changeINSTRUMENT_6_4_33 | Mike |
| 2000-01-01 | add TODO for Monday | Mike |
| 2000-01-01 | do not add redundant settling time flag when changing ampl mode | Mike |
| 2000-01-01 | further refinements to ampl settling time, but need to make it dependent on s... | Mike |
| 2023-11-10 | add an amplitude settling time for SN 14256 repair and future units | Michael J. Chudobiak |
| 2000-01-01 | tweak zout-based duty cycle error check to allow max duty cycle to actually b...INSTRUMENT_6_4_32 | Mike |
| 2000-01-01 | version bumpINSTRUMENT_6_4_31 | Mike |
| 2000-01-01 | fix VXI timeout bug | Mike |
| 2000-01-01 | bump default min PW from 25 to 30 ns due to use of 74HCT151 instead of 74ACT151INSTRUMENT_6_4_30 | Mike |
| 2000-01-01 | version bumpINSTRUMENT_6_4_29 | Mike |
| 2000-01-01 | Do not apply polarity-based PW shift in bot range if bot range is voltage con... | Mike |
| 2000-01-01 | version bumpINSTRUMENT_6_4_28 | Mike |
| 2000-01-01 | fix determination of when to use negative monitor configs | Mike |
| 2000-01-01 | delete an unused variable | Mike |
| 2000-01-01 | Fix crashes caused by uninitialized pointer | Mike |
| 2000-01-01 | reduce ampl_zero_equiv by a factor of 10 in -LV attenuator modeINSTRUMENT_6_4_27c | Mike |
| 2000-01-01 | extended delay when switching attenuators in -LV units | Mike |
| 2000-01-01 | only use attenuators in switchable zout units whem zout is 50 OhmsINSTRUMENT_6_4_27b | Mike |
| 2000-01-01 | simplify checks for enabled switchable_zout | Mike |
| 2000-01-01 | misc fixes to max zout checksINSTRUMENT_6_4_27 | Mike |
| 2000-01-01 | version bump | Mike |
| 2000-01-01 | first attempt at adding lower duty limit when ZOUT=MAX, for -LV option | Mike |
| 2000-01-01 | version bumpINSTRUMENT_6_4_26 | Mike |
| 2000-01-01 | toggle min PW module on powerup also, due to use of IL710 in PCB 340A/B | Mike |
| 2000-01-01 | version bumpINSTRUMENT_6_4_25 | Mike |
| 2000-01-01 | Test encoder against min change and min speed, for free-rolling defective enc... | Mike |
| 2000-01-01 | version bumpINSTRUMENT_6_4_24 | Mike |
| 2000-01-01 | Do not switch polarity relay line in dual-chan dual-pol units, if CH2 ignores... | Mike |
| 2000-01-01 | Major reworking. Set_VI_Control now stores its calculation results for later ...INSTRUMENT_6_4_23d | Mike |
| 2000-01-01 | fully implement disable timing cal percentage check | Mike |
| 2000-01-01 | debug messages showing XTR line changesINSTRUMENT_6_4_23c | Mike |
| 2000-01-01 | remove broken CH2 TTL/ECL logic code, not used in any instruments now | Mike |
| 2000-01-01 | +/- button not working as expected first press after turn-on, fixed. Better d... | Mike |
| 2000-01-01 | Allow CH2 DLY to control trigger PW (for -2CHX). Better debug messages.INSTRUMENT_6_4_23b | Mike |
| 2000-01-01 | version bumpINSTRUMENT_6_4_23 | Mike |
| 2000-01-01 | Dump valid points to console when querying range info, to debug errant cal po... | Mike |
| 2000-01-01 | version bumpINSTRUMENT_6_4_22 | Mike |
| 2000-01-01 | add ability to temporarily disable timing cal percentage check, for burst/sep... | Mike |
| 2000-01-01 | version bumpINSTRUMENT_6_4_21 | Mike |
| 2020-07-27 | add support for new jig pin on keypad 104G | Michael J. Chudobiak |
| 2000-01-01 | version bumpINSTRUMENT_6_4_20 | Mike |
| 2000-01-01 | Only ignore polarity when shown to user. Use polarity when considering calibr... | Mike |
| 2000-01-01 | let rise time go to the lowest hardware-possible value, not just the specifie...INSTRUMENT_6_4_19c | Mike |
