Instrument.git - The instrument daemon

Age	Commit message (Collapse)	Author
2018-05-03	use correct version formatINSTRUMENT_6_4_00	Michael J. Chudobiak

2018-05-03	version bump, new series	Michael J. Chudobiak

2018-05-03	add diag:eprom:resize to copy old 10-point data into new 32-point arrays	root

2018-05-03	Use correct range size in flash init. Old unused vars not initialized any more.	Michael J. Chudobiak

2018-05-03	use new variables and range sizes (but not initialized correctly yet)	Michael J. Chudobiak

2018-05-03	add address locations to comments for new expanded arrays	Michael J. Chudobiak

2018-05-03	Add new variables with 32 entries per range. Not used yet.	Michael J. Chudobiak

2018-05-03	original number of points in each range was 10	Michael J. Chudobiak

2000-01-01	version bumpINSTRUMENT_6_2_37	Mike

2000-01-01	Add commands to add EA distort voltages based on existing ampl cal points	Mike

2000-01-01	First attempt at handling pwl_distort automatically when adding ampl cal points	Mike

2000-01-01	make all aux error messages configurableINSTRUMENT_6_2_36c	Mike

2000-01-01	Version bumpINSTRUMENT_6_2_36b INSTRUMENT_6_2_36	Mike

2000-01-01	Thermal sensor can be used for interlock. Updated error message.	Mike

2000-01-01	version bumpINSTRUMENT_6_2_35	Mike

2000-01-01	Longer gate reset time before cal interval. Needed for highest delays?	Mike

2000-01-01	tagged for 6.2.34INSTRUMENT_6_2_34	Mike

2000-01-01	separate minimum equiv offset from ampl, for AVIR-4-B-OT	Mike

2000-01-01	version bumpINSTRUMENT_6_2_33	Mike

2000-01-01	int func should be void	Mike

2000-01-01	remove one cal point from bottom PRF range	Mike

2000-01-01	version bumpINSTRUMENT_6_2_32	Mike

2000-01-01	toggle non-voltage-controlled range at startup, because it is more likely to ↵	Mike
	have IL710
2000-01-01	better abstraction of method of switching voltage-controlled PW range, for ↵	Mike
	clarity
2000-01-01	version bumpINSTRUMENT_6_2_31	Mike

2000-01-01	better limits on freq/pw for large burst sep calibration	Mike

2000-01-01	limit double pulse mode delay to 50% of periodINSTRUMENT_6_2_30c	Mike

2000-01-01	enforce double pulse minimum spacingINSTRUMENT_6_2_30b	Mike

2000-01-01	version bumpINSTRUMENT_6_2_30	Mike

2000-01-01	throw error if burst mode and double pulse mode enabled at the same time	Mike

2000-01-01	version bumpINSTRUMENT_6_2_29	Mike

2017-10-05	renamed some variables in cal_add for clarity	Michael J. Chudobiak

2017-10-05	auto-handle the EA V1 distort data when deleting an ampl cal point	root

2017-10-05	rename variables in cal_del for clarity	Michael J. Chudobiak

2017-10-05	set aux word when setting nominal amplitude, for EA V1INSTRUMENT_6_2_28b	Michael J. Chudobiak

2000-01-01	version bumpINSTRUMENT_6_2_28	Mike

2000-01-01	implement ampl-dependent arbitrary voltage output - for AVR-E5-B S/N 13618	Mike

2000-01-01	store distortion dac values, not floats	Mike

2000-01-01	added variables for ampl-dependent distortion output	Mike

2000-01-01	Rename piece-wise-linear variables for clarity, dropping reference to ↵	Mike
	obsolete 12bit values
2000-01-01	Do not account for invertedness when calculating duty cycle. Units with ↵INSTRUMENT_6_2_27b	Mike
	invert function are limited by time base circuit, not by average power.
2000-01-01	simplified YES/NO logic	Mike

2000-01-01	replace pol_norm and pol_complement with NO/YES for clarity	Mike

2000-01-01	rename "polarity" variables to "inverted" for clarity	Mike

2000-01-01	bump versionINSTRUMENT_6_2_27	Mike

2000-01-01	added a 100 ns minimum dead time requirement	Mike

2000-01-01	bump versionINSTRUMENT_6_2_26b	Mike

2000-01-01	set advance mode for delay test modeINSTRUMENT_6_2_26	Mike

2000-01-01	don't enable delay test mode for CH2INSTRUMENT_6_2_25b	Mike

2000-01-01	don't do as many error checks when delay word/range is overriddenINSTRUMENT_6_2_25	Mike