| Age | Commit message (Expand) | Author |
|---|
| 2000-01-01 | choose initial PW cal points assuming DDU #2 removed | root |
| 2000-01-01 | toggle both polarities of trigger lines on optocoupler boot toggleINSTRUMENT_6_2_15 | root |
| 2000-01-01 | version bump | root |
| 2000-01-01 | try to turn output off on power fail | root |
| 2000-01-01 | version bumpINSTRUMENT_6_2_14 | root |
| 2000-01-01 | fix last patch | root |
| 2016-09-09 | additional initial cal point per range for burst mode | Michael J. Chudobiak |
| 2016-09-09 | additional address comments in flash for clarity | Michael J. Chudobiak |
| 1970-01-01 | bumped versionINSTRUMENT_6_2_13 | root |
| 1970-01-01 | fix non-working linear interpolation, = vs == | root |
| 2000-01-01 | set minimum allowed PRF during PW/delay calibration | root |
| 2000-01-01 | version bump to 6.2.12INSTRUMENT_6_2_12 | root |
| 2000-01-01 | remove failed 3 point interpolation scheme | root |
| 2000-01-01 | add, but don't use, 3 pt inversion interpolation - doesn't work well! | root |
| 2000-01-01 | separate function for inverse interpolation of X given desired Y | root |
| 2000-01-01 | separate function for linear interpolation of X given desired Y | root |
| 1970-01-01 | add PW distortion for AVR-E, AVIR, AVL. 0% at max amplitude, 100% below set v...INSTRUMENT_6_2_11b | root |
| 1970-01-01 | version bumpINSTRUMENT_6_2_11 | root |
| 1970-01-01 | fix error in pw/delay control introduced by voltage-controlled 2CH delay | root |
| 1970-01-01 | version bump, for 2CHPPINSTRUMENT_6_2_10 | root |
| 1970-01-01 | for 2CHPP CH2 delay cal, use existing parameters | root |
| 1970-01-01 | use delay magnitude to set test PRF since it can be negative, and simplify ex... | root |
| 1970-01-01 | first attempt at implementing CH2 2CHPP delay function | root |
| 1970-01-01 | added volt_ctrl_delay, for 2CHPP on CH2 | root |
| 1970-01-01 | move attenuator code out of CH1-only block, so it works for CH2INSTRUMENT_6_2_09c | root |
| 1970-01-01 | use XTR1 and XTR4 for dual-channel single attenuators, not XTR1 and XTR2 | root |
| 1970-01-01 | do not set XTR polarity line for CH2 if not dual-polarity, to save XTR lines | root |
| 1970-01-01 | add missing headerINSTRUMENT_6_2_09b | root |
| 1970-01-01 | version bumpINSTRUMENT_6_2_09 | root |
| 1970-01-01 | handle default delay better for CH2 of 2CHPP | root |
| 1970-01-01 | accept only simple positive integers in commands, reverses last commit | root |
| 1970-01-01 | accept user int parameters in floating format for scpi compliance | root |
| 1970-01-01 | stronger checking of numeric parameter formats | root |
| 1970-01-01 | version bumpINSTRUMENT_6_2_08 | root |
| 1970-01-01 | hide delay feature on AVR-EBT1-B by setting max_delay to 0.0 | root |
| 1970-01-01 | version bumpINSTRUMENT_6_2_07 | root |
| 1970-01-01 | fix numeric string detection in parameter/units by anchoring regex | root |
| 2016-04-29 | tagged for 6.2.06INSTRUMENT_6_2_06 | Michael J. Chudobiak |
| 2016-04-29 | implement CH2 attenuator ranges | Michael J. Chudobiak |
| 1970-01-01 | version bumpINSTRUMENT_6_2_05 | root |
| 1970-01-01 | added support for sequential vs binary attenuator stages | root |
| 2000-01-01 | version bumpINSTRUMENT_6_2_04 | root |
| 2000-01-01 | toggle trigger at boot, if specified, for IL710 | root |
| 2016-04-06 | add toggle_trig_at_boot for IL710 initialization | Michael J. Chudobiak |
| 1970-01-01 | show FW version and controller type (BB or OL) at startupINSTRUMENT_6_2_03 | root |
| 2000-01-01 | enable power_fail for olimex boards (tie LCD conn pin 14 on EVB to gnd) | root |
| 2000-01-01 | add printf showing if TNT4882 found, for debugging | root |
| 2016-02-18 | different serial ports on Olimex | Michael J. Chudobiak |
| 2000-01-01 | enable most bus features on Olimex | root |
| 2000-01-01 | pre-release bump | root |
