Age | Commit message (Expand) | Author |
2000-01-01 | Fix crashes caused by uninitialized pointer | Mike |
2000-01-01 | reduce ampl_zero_equiv by a factor of 10 in -LV attenuator modeINSTRUMENT_6_4_27c | Mike |
2000-01-01 | extended delay when switching attenuators in -LV units | Mike |
2000-01-01 | only use attenuators in switchable zout units whem zout is 50 OhmsINSTRUMENT_6_4_27b | Mike |
2000-01-01 | simplify checks for enabled switchable_zout | Mike |
2000-01-01 | misc fixes to max zout checksINSTRUMENT_6_4_27 | Mike |
2000-01-01 | version bump | Mike |
2000-01-01 | first attempt at adding lower duty limit when ZOUT=MAX, for -LV option | Mike |
2000-01-01 | version bumpINSTRUMENT_6_4_26 | Mike |
2000-01-01 | toggle min PW module on powerup also, due to use of IL710 in PCB 340A/B | Mike |
2000-01-01 | version bumpINSTRUMENT_6_4_25 | Mike |
2000-01-01 | Test encoder against min change and min speed, for free-rolling defective enc... | Mike |
2000-01-01 | version bumpINSTRUMENT_6_4_24 | Mike |
2000-01-01 | Do not switch polarity relay line in dual-chan dual-pol units, if CH2 ignores... | Mike |
2000-01-01 | Major reworking. Set_VI_Control now stores its calculation results for later ...INSTRUMENT_6_4_23d | Mike |
2000-01-01 | fully implement disable timing cal percentage check | Mike |
2000-01-01 | debug messages showing XTR line changesINSTRUMENT_6_4_23c | Mike |
2000-01-01 | remove broken CH2 TTL/ECL logic code, not used in any instruments now | Mike |
2000-01-01 | +/- button not working as expected first press after turn-on, fixed. Better d... | Mike |
2000-01-01 | Allow CH2 DLY to control trigger PW (for -2CHX). Better debug messages.INSTRUMENT_6_4_23b | Mike |
2000-01-01 | version bumpINSTRUMENT_6_4_23 | Mike |
2000-01-01 | Dump valid points to console when querying range info, to debug errant cal po... | Mike |
2000-01-01 | version bumpINSTRUMENT_6_4_22 | Mike |
2000-01-01 | add ability to temporarily disable timing cal percentage check, for burst/sep... | Mike |
2000-01-01 | version bumpINSTRUMENT_6_4_21 | Mike |
2020-07-27 | add support for new jig pin on keypad 104G | Michael J. Chudobiak |
2000-01-01 | version bumpINSTRUMENT_6_4_20 | Mike |
2000-01-01 | Only ignore polarity when shown to user. Use polarity when considering calibr... | Mike |
2000-01-01 | let rise time go to the lowest hardware-possible value, not just the specifie...INSTRUMENT_6_4_19c | Mike |
2000-01-01 | reduce min rise time cal points to reflect faster 266D | Mike |
2000-01-01 | same as last, missed a spotINSTRUMENT_6_4_19b | Mike |
2000-01-01 | tagged for 6.4.19INSTRUMENT_6_4_19 | Mike |
2000-01-01 | ampl_zero_equiv can be large in some AVRQ units, use smallest_allowed_number ... | Mike |
2000-01-01 | fix encoder clearingINSTRUMENT_6_4_18b | Mike |
2000-01-01 | version bumpINSTRUMENT_6_4_18 | Mike |
2000-01-01 | ignore tiniest encoder steps | Mike |
2020-03-18 | version bumpINSTRUMENT_6_4_17 | Michael J. Chudobiak |
2020-03-18 | add an "ALIVE" output, to switch on VCC2 in AVRQ (for example) | Michael J. Chudobiak |
2000-01-01 | version bumpINSTRUMENT_6_4_16 | Mike |
2000-01-01 | allow mult/div by 10 of burst count values | Mike |
2000-01-01 | Simplify needlessly complex error handling when adjusting encoder | Mike |
2000-01-01 | Simplify needlessly complex error handling when mult/div menu values | Mike |
2000-01-01 | Don't move arrow if only one mode. Fix amplitude mode list.INSTRUMENT_6_4_15b | Mike |
2000-01-01 | version bumpINSTRUMENT_6_4_15 | Mike |
2000-01-01 | tidy amplitude menu code | Mike |
2000-01-01 | Don't write GPIB address to flash until CHANGE button pressed, to avoid weird... | Mike |
2000-01-01 | version bumpINSTRUMENT_6_4_14 | Mike |
2000-01-01 | another divide-by-zero error | Mike |
2000-01-01 | version bumpINSTRUMENT_6_4_13 | Mike |
2019-07-16 | forward port of avg_error calc divide-by-zero fix from AVR-8A-B-P-QTKB repair | Michael J. Chudobiak |