Age | Commit message (Expand) | Author |
2000-01-01 | Allow up to 16 DACs, by adding PCB 313A | Mike |
2000-01-01 | define new I2C ports for PCB 313A DAC board | Mike |
2000-01-01 | version bumpINSTRUMENT_6_4_03c | Mike |
2000-01-01 | make drive polarity of zout relay configurable for -R50 units and PCB 308AINSTRUMENT_6_4_03b | Mike |
2000-01-01 | version bumpINSTRUMENT_6_4_02 | Mike |
2000-01-01 | Use 500 ns PW for IL710 initialization, to force use of PGC-P,-N in AVR-E3-W3 | Mike |
2018-05-07 | version bumpINSTRUMENT_6_4_01 | Michael J. Chudobiak |
2018-05-07 | add ability to just copy old-style ampl and os initial config data to new 32-... | Michael J. Chudobiak |
2018-05-07 | added more address comments | Michael J. Chudobiak |
2018-05-03 | Removed missed hard-coded range sizesINSTRUMENT_6_4_00b | Michael J. Chudobiak |
2018-05-03 | use correct version formatINSTRUMENT_6_4_00 | Michael J. Chudobiak |
2018-05-03 | version bump, new series | Michael J. Chudobiak |
2018-05-03 | add diag:eprom:resize to copy old 10-point data into new 32-point arrays | root |
2018-05-03 | Use correct range size in flash init. Old unused vars not initialized any more. | Michael J. Chudobiak |
2018-05-03 | use new variables and range sizes (but not initialized correctly yet) | Michael J. Chudobiak |
2018-05-03 | add address locations to comments for new expanded arrays | Michael J. Chudobiak |
2018-05-03 | Add new variables with 32 entries per range. Not used yet. | Michael J. Chudobiak |
2018-05-03 | original number of points in each range was 10 | Michael J. Chudobiak |
2000-01-01 | version bumpINSTRUMENT_6_2_37 | Mike |
2000-01-01 | Add commands to add EA distort voltages based on existing ampl cal points | Mike |
2000-01-01 | First attempt at handling pwl_distort automatically when adding ampl cal points | Mike |
2000-01-01 | make all aux error messages configurableINSTRUMENT_6_2_36c | Mike |
2000-01-01 | Version bumpINSTRUMENT_6_2_36bINSTRUMENT_6_2_36 | Mike |
2000-01-01 | Thermal sensor can be used for interlock. Updated error message. | Mike |
2000-01-01 | version bumpINSTRUMENT_6_2_35 | Mike |
2000-01-01 | Longer gate reset time before cal interval. Needed for highest delays? | Mike |
2000-01-01 | tagged for 6.2.34INSTRUMENT_6_2_34 | Mike |
2000-01-01 | separate minimum equiv offset from ampl, for AVIR-4-B-OT | Mike |
2000-01-01 | version bumpINSTRUMENT_6_2_33 | Mike |
2000-01-01 | int func should be void | Mike |
2000-01-01 | remove one cal point from bottom PRF range | Mike |
2000-01-01 | version bumpINSTRUMENT_6_2_32 | Mike |
2000-01-01 | toggle non-voltage-controlled range at startup, because it is more likely to ... | Mike |
2000-01-01 | better abstraction of method of switching voltage-controlled PW range, for cl... | Mike |
2000-01-01 | version bumpINSTRUMENT_6_2_31 | Mike |
2000-01-01 | better limits on freq/pw for large burst sep calibration | Mike |
2000-01-01 | limit double pulse mode delay to 50% of periodINSTRUMENT_6_2_30c | Mike |
2000-01-01 | enforce double pulse minimum spacingINSTRUMENT_6_2_30b | Mike |
2000-01-01 | version bumpINSTRUMENT_6_2_30 | Mike |
2000-01-01 | throw error if burst mode and double pulse mode enabled at the same time | Mike |
2000-01-01 | version bumpINSTRUMENT_6_2_29 | Mike |
2017-10-05 | renamed some variables in cal_add for clarity | Michael J. Chudobiak |
2017-10-05 | auto-handle the EA V1 distort data when deleting an ampl cal point | root |
2017-10-05 | rename variables in cal_del for clarity | Michael J. Chudobiak |
2017-10-05 | set aux word when setting nominal amplitude, for EA V1INSTRUMENT_6_2_28b | Michael J. Chudobiak |
2000-01-01 | version bumpINSTRUMENT_6_2_28 | Mike |
2000-01-01 | implement ampl-dependent arbitrary voltage output - for AVR-E5-B S/N 13618 | Mike |
2000-01-01 | store distortion dac values, not floats | Mike |
2000-01-01 | added variables for ampl-dependent distortion output | Mike |
2000-01-01 | Rename piece-wise-linear variables for clarity, dropping reference to obsolet... | Mike |