summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2017-10-05set aux word when setting nominal amplitude, for EA V1INSTRUMENT_6_2_28bMichael J. Chudobiak
2000-01-01version bumpINSTRUMENT_6_2_28Mike
2000-01-01implement ampl-dependent arbitrary voltage output - for AVR-E5-B S/N 13618Mike
2000-01-01store distortion dac values, not floatsMike
2000-01-01added variables for ampl-dependent distortion outputMike
2000-01-01Rename piece-wise-linear variables for clarity, dropping reference to ↵Mike
obsolete 12bit values
2000-01-01Do not account for invertedness when calculating duty cycle. Units with ↵INSTRUMENT_6_2_27bMike
invert function are limited by time base circuit, not by average power.
2000-01-01simplified YES/NO logicMike
2000-01-01replace pol_norm and pol_complement with NO/YES for clarityMike
2000-01-01rename "polarity" variables to "inverted" for clarityMike
2000-01-01bump versionINSTRUMENT_6_2_27Mike
2000-01-01added a 100 ns minimum dead time requirementMike
2000-01-01bump versionINSTRUMENT_6_2_26bMike
2000-01-01set advance mode for delay test modeINSTRUMENT_6_2_26Mike
2000-01-01don't enable delay test mode for CH2INSTRUMENT_6_2_25bMike
2000-01-01don't do as many error checks when delay word/range is overriddenINSTRUMENT_6_2_25Mike
2000-01-01more useful error message when setting CH2 delay calMike
2000-01-01more specific errors during cal min/max check, and more initial cal pointsMike
2017-05-25version bumpINSTRUMENT_6_2_24Michael J. Chudobiak
2017-05-23fix min/max cal point check for units with non-zero rst amplitude (AVRQ-5-B-AHV)Michael J. Chudobiak
1970-01-01version bumpINSTRUMENT_6_2_23mjc
1970-01-01Enforce minimum ampl magnitude (based on zero_equiv_ampl) in AVRQ -AHV, -XHV ↵mjc
options
2000-01-01version bumpINSTRUMENT_6_2_22mjc
2000-01-01self-cal needs at least 2 periods for PW cal measurement timemjc
2000-01-01version bumpINSTRUMENT_6_2_21mjc
2000-01-01make self-cal min count configurablemjc
2000-01-01make self-cal reference frequency configurableMike
2000-01-01added ability to increase output-on delayMike
2000-01-01added get_float_with_min functionMike
2000-01-01added get_bounded_float functionMike
2017-03-22reduced minimum self-cal measurement from 100us to 40us (0.25% resolution)Michael J. Chudobiak
2016-12-12version bumpINSTRUMENT_6_2_20Michael J. Chudobiak
2016-12-12Revert force-output-on during timing cal option. Too complex, little reward.Michael J. Chudobiak
1970-01-01version bumpINSTRUMENT_6_2_19root
1970-01-01allow option to force output on during timing calroot
2000-01-01version bumpINSTRUMENT_6_2_18mjc
2000-01-01Additional PRF points for 0.1 Hz operationmjc
2000-01-01version bumpINSTRUMENT_6_2_17root
2000-01-01fixed incorrect init of burst, prf integersroot
2000-01-01version bumpINSTRUMENT_6_2_16root
2000-01-01choose initial PW cal points assuming DDU #2 removedroot
2000-01-01toggle both polarities of trigger lines on optocoupler boot toggleINSTRUMENT_6_2_15root
2000-01-01version bumproot
2000-01-01try to turn output off on power failroot
2000-01-01version bumpINSTRUMENT_6_2_14root
2000-01-01fix last patchroot
2016-09-09additional initial cal point per range for burst modeMichael J. Chudobiak
2016-09-09additional address comments in flash for clarityMichael J. Chudobiak
1970-01-01bumped versionINSTRUMENT_6_2_13root
1970-01-01fix non-working linear interpolation, = vs ==root