Instrument.git - The instrument daemon

Age	Commit message (Collapse)	Author
2000-01-01	throw error if burst mode and double pulse mode enabled at the same time	Mike

2000-01-01	version bumpINSTRUMENT_6_2_29	Mike

2017-10-05	renamed some variables in cal_add for clarity	Michael J. Chudobiak

2017-10-05	auto-handle the EA V1 distort data when deleting an ampl cal point	root

2017-10-05	rename variables in cal_del for clarity	Michael J. Chudobiak

2017-10-05	set aux word when setting nominal amplitude, for EA V1INSTRUMENT_6_2_28b	Michael J. Chudobiak

2000-01-01	version bumpINSTRUMENT_6_2_28	Mike

2000-01-01	implement ampl-dependent arbitrary voltage output - for AVR-E5-B S/N 13618	Mike

2000-01-01	store distortion dac values, not floats	Mike

2000-01-01	added variables for ampl-dependent distortion output	Mike

2000-01-01	Rename piece-wise-linear variables for clarity, dropping reference to ↵	Mike
	obsolete 12bit values
2000-01-01	Do not account for invertedness when calculating duty cycle. Units with ↵INSTRUMENT_6_2_27b	Mike
	invert function are limited by time base circuit, not by average power.
2000-01-01	simplified YES/NO logic	Mike

2000-01-01	replace pol_norm and pol_complement with NO/YES for clarity	Mike

2000-01-01	rename "polarity" variables to "inverted" for clarity	Mike

2000-01-01	bump versionINSTRUMENT_6_2_27	Mike

2000-01-01	added a 100 ns minimum dead time requirement	Mike

2000-01-01	bump versionINSTRUMENT_6_2_26b	Mike

2000-01-01	set advance mode for delay test modeINSTRUMENT_6_2_26	Mike

2000-01-01	don't enable delay test mode for CH2INSTRUMENT_6_2_25b	Mike

2000-01-01	don't do as many error checks when delay word/range is overriddenINSTRUMENT_6_2_25	Mike

2000-01-01	more useful error message when setting CH2 delay cal	Mike

2000-01-01	more specific errors during cal min/max check, and more initial cal points	Mike

2017-05-25	version bumpINSTRUMENT_6_2_24	Michael J. Chudobiak

2017-05-23	fix min/max cal point check for units with non-zero rst amplitude (AVRQ-5-B-AHV)	Michael J. Chudobiak

1970-01-01	version bumpINSTRUMENT_6_2_23	mjc

1970-01-01	Enforce minimum ampl magnitude (based on zero_equiv_ampl) in AVRQ -AHV, -XHV ↵	mjc
	options
2000-01-01	version bumpINSTRUMENT_6_2_22	mjc

2000-01-01	self-cal needs at least 2 periods for PW cal measurement time	mjc

2000-01-01	version bumpINSTRUMENT_6_2_21	mjc

2000-01-01	make self-cal min count configurable	mjc

2000-01-01	make self-cal reference frequency configurable	Mike

2000-01-01	added ability to increase output-on delay	Mike

2000-01-01	added get_float_with_min function	Mike

2000-01-01	added get_bounded_float function	Mike

2017-03-22	reduced minimum self-cal measurement from 100us to 40us (0.25% resolution)	Michael J. Chudobiak

2016-12-12	version bumpINSTRUMENT_6_2_20	Michael J. Chudobiak

2016-12-12	Revert force-output-on during timing cal option. Too complex, little reward.	Michael J. Chudobiak

1970-01-01	version bumpINSTRUMENT_6_2_19	root

1970-01-01	allow option to force output on during timing cal	root

2000-01-01	version bumpINSTRUMENT_6_2_18	mjc

2000-01-01	Additional PRF points for 0.1 Hz operation	mjc

2000-01-01	version bumpINSTRUMENT_6_2_17	root

2000-01-01	fixed incorrect init of burst, prf integers	root

2000-01-01	version bumpINSTRUMENT_6_2_16	root

2000-01-01	choose initial PW cal points assuming DDU #2 removed	root

2000-01-01	toggle both polarities of trigger lines on optocoupler boot toggleINSTRUMENT_6_2_15	root

2000-01-01	version bump	root

2000-01-01	try to turn output off on power fail	root

2000-01-01	version bumpINSTRUMENT_6_2_14	root