summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2000-01-01only use attenuators in switchable zout units whem zout is 50 OhmsINSTRUMENT_6_4_27bMike
2000-01-01simplify checks for enabled switchable_zoutMike
2000-01-01misc fixes to max zout checksINSTRUMENT_6_4_27Mike
2000-01-01version bumpMike
2000-01-01first attempt at adding lower duty limit when ZOUT=MAX, for -LV optionMike
2000-01-01version bumpINSTRUMENT_6_4_26Mike
2000-01-01toggle min PW module on powerup also, due to use of IL710 in PCB 340A/BMike
2000-01-01version bumpINSTRUMENT_6_4_25Mike
2000-01-01Test encoder against min change and min speed, for free-rolling defective ↵Mike
encoders
2000-01-01version bumpINSTRUMENT_6_4_24Mike
2000-01-01Do not switch polarity relay line in dual-chan dual-pol units, if CH2 ↵Mike
ignores POL (like AVRK-DPF)
2000-01-01Major reworking. Set_VI_Control now stores its calculation results for later ↵INSTRUMENT_6_4_23dMike
reference. This fixes the problem of adding cal points to parameters with large adjustments. The x values are now correct, but the user must still manually compensate for y changes.
2000-01-01fully implement disable timing cal percentage checkMike
2000-01-01debug messages showing XTR line changesINSTRUMENT_6_4_23cMike
2000-01-01remove broken CH2 TTL/ECL logic code, not used in any instruments nowMike
2000-01-01+/- button not working as expected first press after turn-on, fixed. Better ↵Mike
debugging messages.
2000-01-01Allow CH2 DLY to control trigger PW (for -2CHX). Better debug messages.INSTRUMENT_6_4_23bMike
2000-01-01version bumpINSTRUMENT_6_4_23Mike
2000-01-01Dump valid points to console when querying range info, to debug errant cal ↵Mike
points
2000-01-01version bumpINSTRUMENT_6_4_22Mike
2000-01-01add ability to temporarily disable timing cal percentage check, for ↵Mike
burst/sep/dly2
2000-01-01version bumpINSTRUMENT_6_4_21Mike
2020-07-27add support for new jig pin on keypad 104GMichael J. Chudobiak
2000-01-01version bumpINSTRUMENT_6_4_20Mike
2000-01-01Only ignore polarity when shown to user. Use polarity when considering ↵Mike
calibration ranges.
2000-01-01let rise time go to the lowest hardware-possible value, not just the ↵INSTRUMENT_6_4_19cMike
specified minimum - for AVRQ
2000-01-01reduce min rise time cal points to reflect faster 266DMike
2000-01-01same as last, missed a spotINSTRUMENT_6_4_19bMike
2000-01-01tagged for 6.4.19INSTRUMENT_6_4_19Mike
2000-01-01ampl_zero_equiv can be large in some AVRQ units, use smallest_allowed_number ↵Mike
for comparisons instead
2000-01-01fix encoder clearingINSTRUMENT_6_4_18bMike
2000-01-01version bumpINSTRUMENT_6_4_18Mike
2000-01-01ignore tiniest encoder stepsMike
2020-03-18version bumpINSTRUMENT_6_4_17Michael J. Chudobiak
2020-03-18add an "ALIVE" output, to switch on VCC2 in AVRQ (for example)Michael J. Chudobiak
2000-01-01version bumpINSTRUMENT_6_4_16Mike
2000-01-01allow mult/div by 10 of burst count valuesMike
2000-01-01Simplify needlessly complex error handling when adjusting encoderMike
2000-01-01Simplify needlessly complex error handling when mult/div menu valuesMike
2000-01-01Don't move arrow if only one mode. Fix amplitude mode list.INSTRUMENT_6_4_15bMike
2000-01-01version bumpINSTRUMENT_6_4_15Mike
2000-01-01tidy amplitude menu codeMike
2000-01-01Don't write GPIB address to flash until CHANGE button pressed, to avoid ↵Mike
weird pauses
2000-01-01version bumpINSTRUMENT_6_4_14Mike
2000-01-01another divide-by-zero errorMike
2000-01-01version bumpINSTRUMENT_6_4_13Mike
2019-07-16forward port of avg_error calc divide-by-zero fix from AVR-8A-B-P-QTKB repairMichael J. Chudobiak
2000-01-01version bumpINSTRUMENT_6_4_12Mike
2000-01-01do not reset state before calibrating rise time in AVRQMike
2019-01-08version bumpINSTRUMENT_6_4_11Michael J. Chudobiak
generated by cgit (git 2.34.1) at 2024-12-23 09:02:57 +0000