| Age | Commit message (Expand) | Author |
|---|
| 2000-01-01 | Dump valid points to console when querying range info, to debug errant cal po... | Mike |
| 2000-01-01 | add ability to temporarily disable timing cal percentage check, for burst/sep... | Mike |
| 2000-01-01 | Only ignore polarity when shown to user. Use polarity when considering calibr... | Mike |
| 2000-01-01 | let rise time go to the lowest hardware-possible value, not just the specifie...INSTRUMENT_6_4_19c | Mike |
| 2000-01-01 | same as last, missed a spotINSTRUMENT_6_4_19b | Mike |
| 2000-01-01 | ignore tiniest encoder steps | Mike |
| 2020-03-18 | add an "ALIVE" output, to switch on VCC2 in AVRQ (for example) | Michael J. Chudobiak |
| 2000-01-01 | do not reset state before calibrating rise time in AVRQ | Mike |
| 2000-01-01 | fix min/max ampl/vout balancing when nulling delay shift calINSTRUMENT_6_4_10b | Mike |
| 2000-01-01 | fix ampl min/max checks when max_ampl is limited by max_vout (some -OT units) | Mike |
| 2000-01-01 | make force_output_fully_off work properly for 2-channel unitsINSTRUMENT_6_4_07b | Mike |
| 2000-01-01 | implement full control of DACs 8-15 | Mike |
| 2000-01-01 | Allow up to 16 DACs, by adding PCB 313A | Mike |
| 2000-01-01 | make drive polarity of zout relay configurable for -R50 units and PCB 308AINSTRUMENT_6_4_03b | Mike |
| 2018-05-03 | Removed missed hard-coded range sizesINSTRUMENT_6_4_00b | Michael J. Chudobiak |
| 2018-05-03 | use new variables and range sizes (but not initialized correctly yet) | Michael J. Chudobiak |
| 2018-05-03 | original number of points in each range was 10 | Michael J. Chudobiak |
| 2000-01-01 | Add commands to add EA distort voltages based on existing ampl cal points | Mike |
| 2000-01-01 | First attempt at handling pwl_distort automatically when adding ampl cal points | Mike |
| 2000-01-01 | Longer gate reset time before cal interval. Needed for highest delays? | Mike |
| 2000-01-01 | separate minimum equiv offset from ampl, for AVIR-4-B-OT | Mike |
| 2000-01-01 | int func should be void | Mike |
| 2000-01-01 | better abstraction of method of switching voltage-controlled PW range, for cl... | Mike |
| 2000-01-01 | better limits on freq/pw for large burst sep calibration | Mike |
| 2017-10-05 | renamed some variables in cal_add for clarity | Michael J. Chudobiak |
| 2017-10-05 | auto-handle the EA V1 distort data when deleting an ampl cal point | root |
| 2017-10-05 | rename variables in cal_del for clarity | Michael J. Chudobiak |
| 2017-10-05 | set aux word when setting nominal amplitude, for EA V1INSTRUMENT_6_2_28b | Michael J. Chudobiak |
| 2000-01-01 | implement ampl-dependent arbitrary voltage output - for AVR-E5-B S/N 13618 | Mike |
| 2000-01-01 | Rename piece-wise-linear variables for clarity, dropping reference to obsolet... | Mike |
| 2000-01-01 | replace pol_norm and pol_complement with NO/YES for clarity | Mike |
| 2000-01-01 | rename "polarity" variables to "inverted" for clarity | Mike |
| 2000-01-01 | set advance mode for delay test modeINSTRUMENT_6_2_26 | Mike |
| 2000-01-01 | don't enable delay test mode for CH2INSTRUMENT_6_2_25b | Mike |
| 2000-01-01 | don't do as many error checks when delay word/range is overriddenINSTRUMENT_6_2_25 | Mike |
| 2000-01-01 | more specific errors during cal min/max check, and more initial cal points | Mike |
| 2017-05-23 | fix min/max cal point check for units with non-zero rst amplitude (AVRQ-5-B-AHV) | Michael J. Chudobiak |
| 1970-01-01 | Enforce minimum ampl magnitude (based on zero_equiv_ampl) in AVRQ -AHV, -XHV ... | mjc |
| 2000-01-01 | self-cal needs at least 2 periods for PW cal measurement time | mjc |
| 2000-01-01 | make self-cal min count configurable | mjc |
| 2000-01-01 | make self-cal reference frequency configurable | Mike |
| 2000-01-01 | added ability to increase output-on delay | Mike |
| 2000-01-01 | added get_float_with_min function | Mike |
| 2000-01-01 | added get_bounded_float function | Mike |
| 2017-03-22 | reduced minimum self-cal measurement from 100us to 40us (0.25% resolution) | Michael J. Chudobiak |
| 2016-12-12 | Revert force-output-on during timing cal option. Too complex, little reward. | Michael J. Chudobiak |
| 1970-01-01 | allow option to force output on during timing cal | root |
| 1970-01-01 | fix non-working linear interpolation, = vs == | root |
| 2000-01-01 | set minimum allowed PRF during PW/delay calibration | root |
| 2000-01-01 | remove failed 3 point interpolation scheme | root |
