| Age | Commit message (Expand) | Author |
|---|
| 2000-01-01 | reduce ampl_zero_equiv by a factor of 10 in -LV attenuator modeINSTRUMENT_6_4_27c | Mike |
| 2000-01-01 | misc fixes to max zout checksINSTRUMENT_6_4_27 | Mike |
| 2000-01-01 | first attempt at adding lower duty limit when ZOUT=MAX, for -LV option | Mike |
| 2000-01-01 | Allow CH2 DLY to control trigger PW (for -2CHX). Better debug messages.INSTRUMENT_6_4_23b | Mike |
| 2020-07-27 | add support for new jig pin on keypad 104G | Michael J. Chudobiak |
| 2000-01-01 | let rise time go to the lowest hardware-possible value, not just the specifie...INSTRUMENT_6_4_19c | Mike |
| 2000-01-01 | another divide-by-zero error | Mike |
| 2019-07-16 | forward port of avg_error calc divide-by-zero fix from AVR-8A-B-P-QTKB repair | Michael J. Chudobiak |
| 2000-01-01 | fix duty cycle calculation when calibrating amplitude | Mike |
| 2018-08-14 | only check pw_rc limit if greater than zeroINSTRUMENT_6_4_05b | Michael J. Chudobiak |
| 2000-01-01 | most error checks now used rationalized limit-check functions | Mike |
| 2000-01-01 | Revert portion of last for burst control. Deal with later. Report error only ... | Mike |
| 2000-01-01 | use standard functions to do simple positive min/max error checks | Mike |
| 2000-01-01 | rename some error messages that flag inappropriate config values | Mike |
| 2000-01-01 | calculate freq-based limits and errors in all modes, not just internal trigge... | Mike |
| 2000-01-01 | added hvps_avg_curr_limit for AVR-8F-B | Mike |
| 2000-01-01 | add cap_for_pw_rc_limit for AVR-8F-B | Mike |
| 2000-01-01 | Add commands to add EA distort voltages based on existing ampl cal points | Mike |
| 2000-01-01 | make all aux error messages configurableINSTRUMENT_6_2_36c | Mike |
| 2000-01-01 | Thermal sensor can be used for interlock. Updated error message. | Mike |
| 2000-01-01 | separate minimum equiv offset from ampl, for AVIR-4-B-OT | Mike |
| 2000-01-01 | limit double pulse mode delay to 50% of periodINSTRUMENT_6_2_30c | Mike |
| 2000-01-01 | enforce double pulse minimum spacingINSTRUMENT_6_2_30b | Mike |
| 2000-01-01 | throw error if burst mode and double pulse mode enabled at the same time | Mike |
| 2000-01-01 | Do not account for invertedness when calculating duty cycle. Units with inver...INSTRUMENT_6_2_27b | Mike |
| 2000-01-01 | simplified YES/NO logic | Mike |
| 2000-01-01 | replace pol_norm and pol_complement with NO/YES for clarity | Mike |
| 2000-01-01 | rename "polarity" variables to "inverted" for clarity | Mike |
| 2000-01-01 | added a 100 ns minimum dead time requirement | Mike |
| 2000-01-01 | more useful error message when setting CH2 delay cal | Mike |
| 2000-01-01 | more specific errors during cal min/max check, and more initial cal points | Mike |
| 1970-01-01 | Enforce minimum ampl magnitude (based on zero_equiv_ampl) in AVRQ -AHV, -XHV ... | mjc |
| 2015-10-07 | purge obsolete AVMP-4-B PW range control mode, bump versionINSTRUMENT_6_0_27 | Michael J. Chudobiak |
| 1970-01-01 | first attempt at adding min/max-only rise time, for -KTA-TRA | root |
| 1970-01-01 | show error message on LCD if GPIB chip not detectedINSTRUMENT_6_0_15 | root |
| 2014-08-14 | remove AVRQ-3-B supportINSTRUMENT_6_0_4 | Michael J. Chudobiak |
| 1970-01-01 | account for min/max fixed amplitudes in error checker | root |
| 1970-01-01 | throw error if old-AVRQ-style high zero equiv ampl is set. obsolete. | root |
| 1970-01-01 | throw error if obsolete ampl min/max-only mode is enabled | root |
| 2014-08-13 | first attempt at better AVRQ amplitude handling | Michael J. Chudobiak |
| 1970-01-01 | limit maximum PRF if offset is high in 101x-OT unitsINSTRUMENT_6_0_2d | root |
| 1999-12-31 | Permit negative delays on CH1 of dual-delay units, for -KMPD | root |
| 1999-12-31 | add config option to force monotonic TRIG-OUT delay when externally triggered. | root |
| 2013-10-02 | Revert "added chans_opposite_polarities for AVR-D3-B-MS1 error checking" | Michael J. Chudobiak |
| 2013-10-02 | Revert "calculate ch1 min/max ampl correctly in AVR-D3-B" | Michael J. Chudobiak |
| 1999-12-31 | calculate ch1 min/max ampl correctly in AVR-D3-B | root |
| 2013-10-02 | added chans_opposite_polarities for AVR-D3-B-MS1 error checking | Michael J. Chudobiak |
| 2013-08-08 | finish ab_mode chankey changes | Michael J. Chudobiak |
| 2013-08-08 | rename ab_mode vars to pw_ctrl_mode, and remove ab_mode chankey | Michael J. Chudobiak |
| 2013-06-25 | forward-port multi-channel min/max fixes from 4.16 | Michael J. Chudobiak |
