Instrument.git - The instrument daemon

Age	Commit message (Collapse)	Author
2000-01-01	store distortion dac values, not floats	Mike

2000-01-01	added variables for ampl-dependent distortion output	Mike

2000-01-01	Rename piece-wise-linear variables for clarity, dropping reference to ↵	Mike
	obsolete 12bit values
2000-01-01	replace pol_norm and pol_complement with NO/YES for clarity	Mike

2000-01-01	rename "polarity" variables to "inverted" for clarity	Mike

2000-01-01	added a 100 ns minimum dead time requirement	Mike

2000-01-01	more specific errors during cal min/max check, and more initial cal points	Mike

2000-01-01	make self-cal min count configurable	mjc

2000-01-01	make self-cal reference frequency configurable	Mike

2000-01-01	added ability to increase output-on delay	Mike

2016-12-12	Revert force-output-on during timing cal option. Too complex, little reward.	Michael J. Chudobiak

1970-01-01	allow option to force output on during timing cal	root

2000-01-01	Additional PRF points for 0.1 Hz operation	mjc

2000-01-01	version bumpINSTRUMENT_6_2_17	root

2000-01-01	fixed incorrect init of burst, prf integers	root

2000-01-01	choose initial PW cal points assuming DDU #2 removed	root

2000-01-01	fix last patch	root

2016-09-09	additional initial cal point per range for burst mode	Michael J. Chudobiak

1970-01-01	add PW distortion for AVR-E, AVIR, AVL. 0% at max amplitude, 100% below set ↵INSTRUMENT_6_2_11b	root
	value
1970-01-01	added volt_ctrl_delay, for 2CHPP on CH2	root

1970-01-01	added support for sequential vs binary attenuator stages	root

2016-04-06	add toggle_trig_at_boot for IL710 initialization	Michael J. Chudobiak

1970-01-01	show FW version and controller type (BB or OL) at startupINSTRUMENT_6_2_03	root

1970-01-01	add mutex around remounting, and add debug messagesINSTRUMENT_6_2_02	root

2000-01-01	remount root mount without hard-coded partition name	root

1970-01-01	fix rs232 and flash initialization	root

1970-01-01	file root normally read-only now, for safe power-off. Major OS changes too.INSTRUMENT_6_2_00	root

1970-01-01	first attempt at adding min/max-only rise time, for -KTA-TRA	root

1970-01-01	add support for double-external-trigger mode in KMPF	root

1970-01-01	allow amplitude to be in a limited negative-only range (AVR-CD2-B)	root

1970-01-01	Allow 64-char model numbersINSTRUMENT_6_0_10	root

2014-10-23	AVR-D4-B mods: if min+max ampl both positive, do not reset to zero	Michael J. Chudobiak

2014-08-26	Do not reset fix_pw_dac_val defaults until unit is fully programmed	Michael J. Chudobiak

2014-08-14	remove AVRQ-3-B supportINSTRUMENT_6_0_4	Michael J. Chudobiak

1970-01-01	set *rcl amplitudes to safe values if fixed amplitudes used	root

2014-08-13	first attempt at better AVRQ amplitude handling	Michael J. Chudobiak

1970-01-01	limit maximum PRF if offset is high in 101x-OT unitsINSTRUMENT_6_0_2d	root

1970-01-01	fixed setting of initial/rst burst separationINSTRUMENT_6_0_2b	root

2014-05-20	Fix the compile error I introduced by calling initFlashValues before it's ↵INSTRUMENT_5_0_12	daniel
	declared
2014-05-20	Ofcourse that won't work as it'll break the CRC, so we truncate the last ↵	Daniel Palmer
	byte after checking the whole thing is correct
2014-05-20	If the struct coming in from disk is smaller than the request size don't ↵	Daniel Palmer
	read the last byte. This stops it from running over a byte that is now where the flash end used to be.
2014-05-20	- Fix the mhash cmake file for Debian/armhf	Daniel Palmer
	- Proposed single line solution to handle flash struct changes
1999-12-31	add config option to force monotonic TRIG-OUT delay when externally triggered.	root

1999-12-31	make CH2 delay changes actually workINSTRUMENT_5_0_9	root

2014-03-26	use PCB 205A for CH2 delay, I2C address changes	Michael J. Chudobiak

1999-12-31	Revert "Revert "add possibility to ignore voltage polarity set by user""	root
	This reverts commit 623db64a55a04e531bb847fa02ef20ce1a05a10c.
1999-12-31	Revert "add possibility to ignore voltage polarity set by user"	root
	This reverts commit 401fd942b84f8a1a8cb48e6c38ebe3dae1ab42ef.
1999-12-31	add possibility to ignore voltage polarity set by user	root

2013-10-02	Revert "added chans_opposite_polarities for AVR-D3-B-MS1 error checking"	Michael J. Chudobiak
	This reverts commit e1678aa56d0d1deaf003e0a04f09d26000d9eca5.
2013-10-02	added chans_opposite_polarities for AVR-D3-B-MS1 error checking	Michael J. Chudobiak