summaryrefslogtreecommitdiff
path: root/flash.c
AgeCommit message (Collapse)Author
2016-12-12Revert force-output-on during timing cal option. Too complex, little reward.Michael J. Chudobiak
1970-01-01allow option to force output on during timing calroot
2000-01-01Additional PRF points for 0.1 Hz operationmjc
2000-01-01version bumpINSTRUMENT_6_2_17root
2000-01-01fixed incorrect init of burst, prf integersroot
2000-01-01choose initial PW cal points assuming DDU #2 removedroot
2000-01-01fix last patchroot
2016-09-09additional initial cal point per range for burst modeMichael J. Chudobiak
1970-01-01add PW distortion for AVR-E, AVIR, AVL. 0% at max amplitude, 100% below set ↵INSTRUMENT_6_2_11broot
value
1970-01-01added volt_ctrl_delay, for 2CHPP on CH2root
1970-01-01added support for sequential vs binary attenuator stagesroot
2016-04-06add toggle_trig_at_boot for IL710 initializationMichael J. Chudobiak
1970-01-01show FW version and controller type (BB or OL) at startupINSTRUMENT_6_2_03root
1970-01-01add mutex around remounting, and add debug messagesINSTRUMENT_6_2_02root
2000-01-01remount root mount without hard-coded partition nameroot
1970-01-01fix rs232 and flash initializationroot
1970-01-01file root normally read-only now, for safe power-off. Major OS changes too.INSTRUMENT_6_2_00root
1970-01-01first attempt at adding min/max-only rise time, for -KTA-TRAroot
1970-01-01add support for double-external-trigger mode in KMPFroot
1970-01-01allow amplitude to be in a limited negative-only range (AVR-CD2-B)root
1970-01-01Allow 64-char model numbersINSTRUMENT_6_0_10root
2014-10-23AVR-D4-B mods: if min+max ampl both positive, do not reset to zeroMichael J. Chudobiak
2014-08-26Do not reset fix_pw_dac_val defaults until unit is fully programmedMichael J. Chudobiak
2014-08-14remove AVRQ-3-B supportINSTRUMENT_6_0_4Michael J. Chudobiak
1970-01-01set *rcl amplitudes to safe values if fixed amplitudes usedroot
2014-08-13first attempt at better AVRQ amplitude handlingMichael J. Chudobiak
1970-01-01limit maximum PRF if offset is high in 101x-OT unitsINSTRUMENT_6_0_2droot
1970-01-01fixed setting of initial/rst burst separationINSTRUMENT_6_0_2broot
2014-05-20Fix the compile error I introduced by calling initFlashValues before it's ↵INSTRUMENT_5_0_12daniel
declared
2014-05-20Ofcourse that won't work as it'll break the CRC, so we truncate the last ↵Daniel Palmer
byte after checking the whole thing is correct
2014-05-20If the struct coming in from disk is smaller than the request size don't ↵Daniel Palmer
read the last byte. This stops it from running over a byte that is now where the flash end used to be.
2014-05-20- Fix the mhash cmake file for Debian/armhfDaniel Palmer
- Proposed single line solution to handle flash struct changes
1999-12-31add config option to force monotonic TRIG-OUT delay when externally triggered.root
1999-12-31make CH2 delay changes actually workINSTRUMENT_5_0_9root
2014-03-26use PCB 205A for CH2 delay, I2C address changesMichael J. Chudobiak
1999-12-31Revert "Revert "add possibility to ignore voltage polarity set by user""root
This reverts commit 623db64a55a04e531bb847fa02ef20ce1a05a10c.
1999-12-31Revert "add possibility to ignore voltage polarity set by user"root
This reverts commit 401fd942b84f8a1a8cb48e6c38ebe3dae1ab42ef.
1999-12-31add possibility to ignore voltage polarity set by userroot
2013-10-02Revert "added chans_opposite_polarities for AVR-D3-B-MS1 error checking"Michael J. Chudobiak
This reverts commit e1678aa56d0d1deaf003e0a04f09d26000d9eca5.
2013-10-02added chans_opposite_polarities for AVR-D3-B-MS1 error checkingMichael J. Chudobiak
1999-12-31fix to make diag:eprom:reset XXXX take effect right awayroot
2013-08-09add ew_xtra_rly config setting to flashMichael J. Chudobiak
2013-08-08added basic parser support for EW mode, and added ew_enabled to flashMichael J. Chudobiak
2013-08-08rename ab_mode vars to pw_ctrl_mode, and remove ab_mode chankeyMichael J. Chudobiak
2013-08-08rename ab_mode_allowed to pw_ab_mode_enabledMichael J. Chudobiak
2013-04-26Add two defines to allow the frozen struct size to be either smaller or ↵daniel
bigger than the target.
1999-12-31use narrower fixed PW on high PRF units like AVM-6-BINSTRUMENT_5_0_4root
1999-12-31astyle fixesroot
1999-12-31when using attenuators, do not go to very top of raw ampl rangeINSTRUMENT_5_0_2root
2013-04-02added attenuator ranges to flashMichael J. Chudobiak