summaryrefslogtreecommitdiff
path: root/flash.c
AgeCommit message (Collapse)Author
2000-01-01first attempt at adding lower duty limit when ZOUT=MAX, for -LV optionMike
2020-07-27add support for new jig pin on keypad 104GMichael J. Chudobiak
2000-01-01reduce min rise time cal points to reflect faster 266DMike
2019-01-08always enable vxi nowMichael J. Chudobiak
2018-11-23enable VXI on unprogrammed boards, for testing without GPIBMichael J. Chudobiak
2000-01-01make max step size deviation configurableINSTRUMENT_6_4_08bMike
2000-01-01added hvps_avg_curr_limit for AVR-8F-BMike
2000-01-01add cap_for_pw_rc_limit for AVR-8F-BMike
2000-01-01make drive polarity of zout relay configurable for -R50 units and PCB 308AINSTRUMENT_6_4_03bMike
2018-05-03Use correct range size in flash init. Old unused vars not initialized any more.Michael J. Chudobiak
2018-05-03use new variables and range sizes (but not initialized correctly yet)Michael J. Chudobiak
2018-05-03original number of points in each range was 10Michael J. Chudobiak
2000-01-01First attempt at handling pwl_distort automatically when adding ampl cal pointsMike
2000-01-01make all aux error messages configurableINSTRUMENT_6_2_36cMike
2000-01-01separate minimum equiv offset from ampl, for AVIR-4-B-OTMike
2000-01-01remove one cal point from bottom PRF rangeMike
2000-01-01enforce double pulse minimum spacingINSTRUMENT_6_2_30bMike
2000-01-01store distortion dac values, not floatsMike
2000-01-01added variables for ampl-dependent distortion outputMike
2000-01-01Rename piece-wise-linear variables for clarity, dropping reference to ↵Mike
obsolete 12bit values
2000-01-01replace pol_norm and pol_complement with NO/YES for clarityMike
2000-01-01rename "polarity" variables to "inverted" for clarityMike
2000-01-01added a 100 ns minimum dead time requirementMike
2000-01-01more specific errors during cal min/max check, and more initial cal pointsMike
2000-01-01make self-cal min count configurablemjc
2000-01-01make self-cal reference frequency configurableMike
2000-01-01added ability to increase output-on delayMike
2016-12-12Revert force-output-on during timing cal option. Too complex, little reward.Michael J. Chudobiak
1970-01-01allow option to force output on during timing calroot
2000-01-01Additional PRF points for 0.1 Hz operationmjc
2000-01-01version bumpINSTRUMENT_6_2_17root
2000-01-01fixed incorrect init of burst, prf integersroot
2000-01-01choose initial PW cal points assuming DDU #2 removedroot
2000-01-01fix last patchroot
2016-09-09additional initial cal point per range for burst modeMichael J. Chudobiak
1970-01-01add PW distortion for AVR-E, AVIR, AVL. 0% at max amplitude, 100% below set ↵INSTRUMENT_6_2_11broot
value
1970-01-01added volt_ctrl_delay, for 2CHPP on CH2root
1970-01-01added support for sequential vs binary attenuator stagesroot
2016-04-06add toggle_trig_at_boot for IL710 initializationMichael J. Chudobiak
1970-01-01show FW version and controller type (BB or OL) at startupINSTRUMENT_6_2_03root
1970-01-01add mutex around remounting, and add debug messagesINSTRUMENT_6_2_02root
2000-01-01remount root mount without hard-coded partition nameroot
1970-01-01fix rs232 and flash initializationroot
1970-01-01file root normally read-only now, for safe power-off. Major OS changes too.INSTRUMENT_6_2_00root
1970-01-01first attempt at adding min/max-only rise time, for -KTA-TRAroot
1970-01-01add support for double-external-trigger mode in KMPFroot
1970-01-01allow amplitude to be in a limited negative-only range (AVR-CD2-B)root
1970-01-01Allow 64-char model numbersINSTRUMENT_6_0_10root
2014-10-23AVR-D4-B mods: if min+max ampl both positive, do not reset to zeroMichael J. Chudobiak
2014-08-26Do not reset fix_pw_dac_val defaults until unit is fully programmedMichael J. Chudobiak
generated by cgit (git 2.34.1) at 2024-12-23 08:08:48 +0000