Age | Commit message (Expand) | Author |
2000-01-01 | Rename piece-wise-linear variables for clarity, dropping reference to obsolet... | Mike |
2000-01-01 | replace pol_norm and pol_complement with NO/YES for clarity | Mike |
2000-01-01 | rename "polarity" variables to "inverted" for clarity | Mike |
2000-01-01 | added a 100 ns minimum dead time requirement | Mike |
2000-01-01 | more specific errors during cal min/max check, and more initial cal points | Mike |
2000-01-01 | make self-cal min count configurable | mjc |
2000-01-01 | make self-cal reference frequency configurable | Mike |
2000-01-01 | added ability to increase output-on delay | Mike |
2016-12-12 | Revert force-output-on during timing cal option. Too complex, little reward. | Michael J. Chudobiak |
1970-01-01 | allow option to force output on during timing cal | root |
2000-01-01 | Additional PRF points for 0.1 Hz operation | mjc |
2000-01-01 | version bumpINSTRUMENT_6_2_17 | root |
2000-01-01 | fixed incorrect init of burst, prf integers | root |
2000-01-01 | choose initial PW cal points assuming DDU #2 removed | root |
2000-01-01 | fix last patch | root |
2016-09-09 | additional initial cal point per range for burst mode | Michael J. Chudobiak |
1970-01-01 | add PW distortion for AVR-E, AVIR, AVL. 0% at max amplitude, 100% below set v...INSTRUMENT_6_2_11b | root |
1970-01-01 | added volt_ctrl_delay, for 2CHPP on CH2 | root |
1970-01-01 | added support for sequential vs binary attenuator stages | root |
2016-04-06 | add toggle_trig_at_boot for IL710 initialization | Michael J. Chudobiak |
1970-01-01 | show FW version and controller type (BB or OL) at startupINSTRUMENT_6_2_03 | root |
1970-01-01 | add mutex around remounting, and add debug messagesINSTRUMENT_6_2_02 | root |
2000-01-01 | remount root mount without hard-coded partition name | root |
1970-01-01 | fix rs232 and flash initialization | root |
1970-01-01 | file root normally read-only now, for safe power-off. Major OS changes too.INSTRUMENT_6_2_00 | root |
1970-01-01 | first attempt at adding min/max-only rise time, for -KTA-TRA | root |
1970-01-01 | add support for double-external-trigger mode in KMPF | root |
1970-01-01 | allow amplitude to be in a limited negative-only range (AVR-CD2-B) | root |
1970-01-01 | Allow 64-char model numbersINSTRUMENT_6_0_10 | root |
2014-10-23 | AVR-D4-B mods: if min+max ampl both positive, do not reset to zero | Michael J. Chudobiak |
2014-08-26 | Do not reset fix_pw_dac_val defaults until unit is fully programmed | Michael J. Chudobiak |
2014-08-14 | remove AVRQ-3-B supportINSTRUMENT_6_0_4 | Michael J. Chudobiak |
1970-01-01 | set *rcl amplitudes to safe values if fixed amplitudes used | root |
2014-08-13 | first attempt at better AVRQ amplitude handling | Michael J. Chudobiak |
1970-01-01 | limit maximum PRF if offset is high in 101x-OT unitsINSTRUMENT_6_0_2d | root |
1970-01-01 | fixed setting of initial/rst burst separationINSTRUMENT_6_0_2b | root |
2014-05-20 | Fix the compile error I introduced by calling initFlashValues before it's dec...INSTRUMENT_5_0_12 | daniel |
2014-05-20 | Ofcourse that won't work as it'll break the CRC, so we truncate the last byte... | Daniel Palmer |
2014-05-20 | If the struct coming in from disk is smaller than the request size don't read... | Daniel Palmer |
2014-05-20 | - Fix the mhash cmake file for Debian/armhf | Daniel Palmer |
1999-12-31 | add config option to force monotonic TRIG-OUT delay when externally triggered. | root |
1999-12-31 | make CH2 delay changes actually workINSTRUMENT_5_0_9 | root |
2014-03-26 | use PCB 205A for CH2 delay, I2C address changes | Michael J. Chudobiak |
1999-12-31 | Revert "Revert "add possibility to ignore voltage polarity set by user"" | root |
1999-12-31 | Revert "add possibility to ignore voltage polarity set by user" | root |
1999-12-31 | add possibility to ignore voltage polarity set by user | root |
2013-10-02 | Revert "added chans_opposite_polarities for AVR-D3-B-MS1 error checking" | Michael J. Chudobiak |
2013-10-02 | added chans_opposite_polarities for AVR-D3-B-MS1 error checking | Michael J. Chudobiak |
1999-12-31 | fix to make diag:eprom:reset XXXX take effect right away | root |
2013-08-09 | add ew_xtra_rly config setting to flash | Michael J. Chudobiak |