summaryrefslogtreecommitdiff
path: root/globals.h
AgeCommit message (Collapse)Author
2000-01-01Allow up to 16 DACs, by adding PCB 313AMike
2000-01-01make drive polarity of zout relay configurable for -R50 units and PCB 308AINSTRUMENT_6_4_03bMike
2018-05-07add ability to just copy old-style ampl and os initial config data to new ↵Michael J. Chudobiak
32-ranges
2018-05-07added more address commentsMichael J. Chudobiak
2018-05-03use new variables and range sizes (but not initialized correctly yet)Michael J. Chudobiak
2018-05-03add address locations to comments for new expanded arraysMichael J. Chudobiak
2018-05-03Add new variables with 32 entries per range. Not used yet.Michael J. Chudobiak
2018-05-03original number of points in each range was 10Michael J. Chudobiak
2000-01-01Add commands to add EA distort voltages based on existing ampl cal pointsMike
2000-01-01make all aux error messages configurableINSTRUMENT_6_2_36cMike
2000-01-01separate minimum equiv offset from ampl, for AVIR-4-B-OTMike
2000-01-01enforce double pulse minimum spacingINSTRUMENT_6_2_30bMike
2000-01-01throw error if burst mode and double pulse mode enabled at the same timeMike
2000-01-01store distortion dac values, not floatsMike
2000-01-01added variables for ampl-dependent distortion outputMike
2000-01-01Rename piece-wise-linear variables for clarity, dropping reference to ↵Mike
obsolete 12bit values
2000-01-01replace pol_norm and pol_complement with NO/YES for clarityMike
2000-01-01rename "polarity" variables to "inverted" for clarityMike
2000-01-01added a 100 ns minimum dead time requirementMike
2000-01-01more specific errors during cal min/max check, and more initial cal pointsMike
1970-01-01Enforce minimum ampl magnitude (based on zero_equiv_ampl) in AVRQ -AHV, -XHV ↵mjc
options
2000-01-01make self-cal min count configurablemjc
2000-01-01make self-cal reference frequency configurableMike
2000-01-01added ability to increase output-on delayMike
2016-12-12Revert force-output-on during timing cal option. Too complex, little reward.Michael J. Chudobiak
1970-01-01allow option to force output on during timing calroot
2000-01-01Additional PRF points for 0.1 Hz operationmjc
2016-09-09additional address comments in flash for clarityMichael J. Chudobiak
1970-01-01add PW distortion for AVR-E, AVIR, AVL. 0% at max amplitude, 100% below set ↵INSTRUMENT_6_2_11broot
value
1970-01-01added volt_ctrl_delay, for 2CHPP on CH2root
1970-01-01added support for sequential vs binary attenuator stagesroot
2016-04-06add toggle_trig_at_boot for IL710 initializationMichael J. Chudobiak
1970-01-01show FW version and controller type (BB or OL) at startupINSTRUMENT_6_2_03root
2000-01-01abstract the hardware identification checksroot
2000-01-01allow longer root device namesroot
2000-01-01close model file properlyroot
2000-01-01add code to detect beaglebone vs olimexroot
1970-01-01turn output off when switching attenuator rangesroot
2015-10-07purge obsolete AVMP-4-B PW range control mode, bump versionINSTRUMENT_6_0_27Michael J. Chudobiak
1970-01-01first attempt at adding min/max-only rise time, for -KTA-TRAroot
1970-01-01add support for double-external-trigger mode in KMPFroot
1970-01-01show error message on LCD if GPIB chip not detectedINSTRUMENT_6_0_15root
1970-01-01Allow 64-char model numbersINSTRUMENT_6_0_10root
2014-08-14remove AVRQ-3-B supportINSTRUMENT_6_0_4Michael J. Chudobiak
1970-01-01throw error if old-AVRQ-style high zero equiv ampl is set. obsolete.root
1970-01-01throw error if obsolete ampl min/max-only mode is enabledroot
2014-08-13first attempt at better AVRQ amplitude handlingMichael J. Chudobiak
1970-01-01limit maximum PRF if offset is high in 101x-OT unitsINSTRUMENT_6_0_2droot
1999-12-31add config option to force monotonic TRIG-OUT delay when externally triggered.root
2014-03-26use PCB 205A for CH2 delay, I2C address changesMichael J. Chudobiak
generated by cgit (git 2.34.1) at 2024-12-29 09:12:03 +0000