| Age | Commit message (Expand) | Author |
|---|
| 2018-05-03 | add address locations to comments for new expanded arrays | Michael J. Chudobiak |
| 2018-05-03 | Add new variables with 32 entries per range. Not used yet. | Michael J. Chudobiak |
| 2018-05-03 | original number of points in each range was 10 | Michael J. Chudobiak |
| 2000-01-01 | Add commands to add EA distort voltages based on existing ampl cal points | Mike |
| 2000-01-01 | make all aux error messages configurableINSTRUMENT_6_2_36c | Mike |
| 2000-01-01 | separate minimum equiv offset from ampl, for AVIR-4-B-OT | Mike |
| 2000-01-01 | enforce double pulse minimum spacingINSTRUMENT_6_2_30b | Mike |
| 2000-01-01 | throw error if burst mode and double pulse mode enabled at the same time | Mike |
| 2000-01-01 | store distortion dac values, not floats | Mike |
| 2000-01-01 | added variables for ampl-dependent distortion output | Mike |
| 2000-01-01 | Rename piece-wise-linear variables for clarity, dropping reference to obsolet... | Mike |
| 2000-01-01 | replace pol_norm and pol_complement with NO/YES for clarity | Mike |
| 2000-01-01 | rename "polarity" variables to "inverted" for clarity | Mike |
| 2000-01-01 | added a 100 ns minimum dead time requirement | Mike |
| 2000-01-01 | more specific errors during cal min/max check, and more initial cal points | Mike |
| 1970-01-01 | Enforce minimum ampl magnitude (based on zero_equiv_ampl) in AVRQ -AHV, -XHV ... | mjc |
| 2000-01-01 | make self-cal min count configurable | mjc |
| 2000-01-01 | make self-cal reference frequency configurable | Mike |
| 2000-01-01 | added ability to increase output-on delay | Mike |
| 2016-12-12 | Revert force-output-on during timing cal option. Too complex, little reward. | Michael J. Chudobiak |
| 1970-01-01 | allow option to force output on during timing cal | root |
| 2000-01-01 | Additional PRF points for 0.1 Hz operation | mjc |
| 2016-09-09 | additional address comments in flash for clarity | Michael J. Chudobiak |
| 1970-01-01 | add PW distortion for AVR-E, AVIR, AVL. 0% at max amplitude, 100% below set v...INSTRUMENT_6_2_11b | root |
| 1970-01-01 | added volt_ctrl_delay, for 2CHPP on CH2 | root |
| 1970-01-01 | added support for sequential vs binary attenuator stages | root |
| 2016-04-06 | add toggle_trig_at_boot for IL710 initialization | Michael J. Chudobiak |
| 1970-01-01 | show FW version and controller type (BB or OL) at startupINSTRUMENT_6_2_03 | root |
| 2000-01-01 | abstract the hardware identification checks | root |
| 2000-01-01 | allow longer root device names | root |
| 2000-01-01 | close model file properly | root |
| 2000-01-01 | add code to detect beaglebone vs olimex | root |
| 1970-01-01 | turn output off when switching attenuator ranges | root |
| 2015-10-07 | purge obsolete AVMP-4-B PW range control mode, bump versionINSTRUMENT_6_0_27 | Michael J. Chudobiak |
| 1970-01-01 | first attempt at adding min/max-only rise time, for -KTA-TRA | root |
| 1970-01-01 | add support for double-external-trigger mode in KMPF | root |
| 1970-01-01 | show error message on LCD if GPIB chip not detectedINSTRUMENT_6_0_15 | root |
| 1970-01-01 | Allow 64-char model numbersINSTRUMENT_6_0_10 | root |
| 2014-08-14 | remove AVRQ-3-B supportINSTRUMENT_6_0_4 | Michael J. Chudobiak |
| 1970-01-01 | throw error if old-AVRQ-style high zero equiv ampl is set. obsolete. | root |
| 1970-01-01 | throw error if obsolete ampl min/max-only mode is enabled | root |
| 2014-08-13 | first attempt at better AVRQ amplitude handling | Michael J. Chudobiak |
| 1970-01-01 | limit maximum PRF if offset is high in 101x-OT unitsINSTRUMENT_6_0_2d | root |
| 1999-12-31 | add config option to force monotonic TRIG-OUT delay when externally triggered. | root |
| 2014-03-26 | use PCB 205A for CH2 delay, I2C address changes | Michael J. Chudobiak |
| 1999-12-31 | Revert "Revert "add possibility to ignore voltage polarity set by user"" | root |
| 1999-12-31 | Revert "add possibility to ignore voltage polarity set by user" | root |
| 1999-12-31 | add possibility to ignore voltage polarity set by user | root |
| 2013-10-02 | Revert "added chans_opposite_polarities for AVR-D3-B-MS1 error checking" | Michael J. Chudobiak |
| 2013-10-02 | added chans_opposite_polarities for AVR-D3-B-MS1 error checking | Michael J. Chudobiak |
