Instrument.git - The instrument daemon

Age	Commit message (Collapse)	Author
2000-01-01	Sleep time is now fraction of max based on DAC changeINSTRUMENT_6_4_33	Mike

2023-11-10	add an amplitude settling time for SN 14256 repair and future units	Michael J. Chudobiak

2000-01-01	misc fixes to max zout checksINSTRUMENT_6_4_27	Mike

2000-01-01	first attempt at adding lower duty limit when ZOUT=MAX, for -LV option	Mike

2000-01-01	Major reworking. Set_VI_Control now stores its calculation results for later ↵INSTRUMENT_6_4_23d	Mike
	reference. This fixes the problem of adding cal points to parameters with large adjustments. The x values are now correct, but the user must still manually compensate for y changes.
2000-01-01	+/- button not working as expected first press after turn-on, fixed. Better ↵	Mike
	debugging messages.
2000-01-01	Allow CH2 DLY to control trigger PW (for -2CHX). Better debug messages.INSTRUMENT_6_4_23b	Mike

2000-01-01	add ability to temporarily disable timing cal percentage check, for ↵	Mike
	burst/sep/dly2
2020-07-27	add support for new jig pin on keypad 104G	Michael J. Chudobiak

2019-01-08	always enable vxi now	Michael J. Chudobiak

2000-01-01	make max step size deviation configurableINSTRUMENT_6_4_08b	Mike

2000-01-01	better monitor averaging (for AVO-8E3 S/N 13790) with auto-reset of average	Mike

2000-01-01	make force_output_fully_off work properly for 2-channel unitsINSTRUMENT_6_4_07b	Mike

2000-01-01	Split inputs into separate lines when multiple interactive commands are received	Mike

2000-01-01	most error checks now used rationalized limit-check functions	Mike

2000-01-01	use standard functions to do simple positive min/max error checks	Mike

2000-01-01	rename some error messages that flag inappropriate config values	Mike

2000-01-01	added hvps_avg_curr_limit for AVR-8F-B	Mike

2000-01-01	add cap_for_pw_rc_limit for AVR-8F-B	Mike

2000-01-01	Allow up to 16 DACs, by adding PCB 313A	Mike

2000-01-01	make drive polarity of zout relay configurable for -R50 units and PCB 308AINSTRUMENT_6_4_03b	Mike

2018-05-07	add ability to just copy old-style ampl and os initial config data to new ↵	Michael J. Chudobiak
	32-ranges
2018-05-07	added more address comments	Michael J. Chudobiak

2018-05-03	use new variables and range sizes (but not initialized correctly yet)	Michael J. Chudobiak

2018-05-03	add address locations to comments for new expanded arrays	Michael J. Chudobiak

2018-05-03	Add new variables with 32 entries per range. Not used yet.	Michael J. Chudobiak

2018-05-03	original number of points in each range was 10	Michael J. Chudobiak

2000-01-01	Add commands to add EA distort voltages based on existing ampl cal points	Mike

2000-01-01	make all aux error messages configurableINSTRUMENT_6_2_36c	Mike

2000-01-01	separate minimum equiv offset from ampl, for AVIR-4-B-OT	Mike

2000-01-01	enforce double pulse minimum spacingINSTRUMENT_6_2_30b	Mike

2000-01-01	throw error if burst mode and double pulse mode enabled at the same time	Mike

2000-01-01	store distortion dac values, not floats	Mike

2000-01-01	added variables for ampl-dependent distortion output	Mike

2000-01-01	Rename piece-wise-linear variables for clarity, dropping reference to ↵	Mike
	obsolete 12bit values
2000-01-01	replace pol_norm and pol_complement with NO/YES for clarity	Mike

2000-01-01	rename "polarity" variables to "inverted" for clarity	Mike

2000-01-01	added a 100 ns minimum dead time requirement	Mike

2000-01-01	more specific errors during cal min/max check, and more initial cal points	Mike

1970-01-01	Enforce minimum ampl magnitude (based on zero_equiv_ampl) in AVRQ -AHV, -XHV ↵	mjc
	options
2000-01-01	make self-cal min count configurable	mjc

2000-01-01	make self-cal reference frequency configurable	Mike

2000-01-01	added ability to increase output-on delay	Mike

2016-12-12	Revert force-output-on during timing cal option. Too complex, little reward.	Michael J. Chudobiak

1970-01-01	allow option to force output on during timing cal	root

2000-01-01	Additional PRF points for 0.1 Hz operation	mjc

2016-09-09	additional address comments in flash for clarity	Michael J. Chudobiak

1970-01-01	add PW distortion for AVR-E, AVIR, AVL. 0% at max amplitude, 100% below set ↵INSTRUMENT_6_2_11b	root
	value
1970-01-01	added volt_ctrl_delay, for 2CHPP on CH2	root

1970-01-01	added support for sequential vs binary attenuator stages	root