diff options
| -rw-r--r-- | arch/powerpc/cpu/mpc85xx/cpu.c | 11 | ||||
| -rw-r--r-- | arch/powerpc/cpu/mpc85xx/cpu_init.c | 19 | ||||
| -rw-r--r-- | arch/powerpc/cpu/mpc85xx/cpu_init_nand.c | 15 | ||||
| -rw-r--r-- | arch/powerpc/cpu/mpc85xx/fsl_corenet_serdes.c | 106 | ||||
| -rw-r--r-- | arch/powerpc/cpu/mpc85xx/speed.c | 8 | ||||
| -rw-r--r-- | arch/powerpc/include/asm/config_mpc85xx.h | 14 | ||||
| -rw-r--r-- | arch/powerpc/include/asm/fsl_ddr_sdram.h | 1 | ||||
| -rw-r--r-- | arch/powerpc/include/asm/immap_85xx.h | 53 | ||||
| -rw-r--r-- | board/freescale/corenet_ds/tlb.c | 12 | ||||
| -rw-r--r-- | board/freescale/p1022ds/p1022ds.c | 56 | ||||
| -rw-r--r-- | boards.cfg | 1 | ||||
| -rw-r--r-- | doc/README.p1022ds | 24 | ||||
| -rw-r--r-- | doc/README.p4080ds | 32 | ||||
| -rw-r--r-- | drivers/mmc/fsl_esdhc.c | 8 | ||||
| -rw-r--r-- | drivers/qe/uec.c | 37 | ||||
| -rw-r--r-- | include/configs/MPC8536DS.h | 18 | ||||
| -rw-r--r-- | include/configs/MPC8569MDS.h | 12 | ||||
| -rw-r--r-- | include/configs/MPC8572DS.h | 18 | ||||
| -rw-r--r-- | include/configs/P1022DS.h | 17 | ||||
| -rw-r--r-- | include/configs/P1_P2_RDB.h | 12 | ||||
| -rw-r--r-- | include/configs/P2020DS.h | 14 | ||||
| -rw-r--r-- | include/configs/corenet_ds.h | 50 | ||||
| -rw-r--r-- | include/fsl_esdhc.h | 15 |
23 files changed, 394 insertions, 159 deletions
diff --git a/arch/powerpc/cpu/mpc85xx/cpu.c b/arch/powerpc/cpu/mpc85xx/cpu.c index 49ea6cc752..f5b39c067c 100644 --- a/arch/powerpc/cpu/mpc85xx/cpu.c +++ b/arch/powerpc/cpu/mpc85xx/cpu.c @@ -299,6 +299,16 @@ void mpc85xx_reginfo(void) /* Common ddr init for non-corenet fsl 85xx platforms */ #ifndef CONFIG_FSL_CORENET +#if defined(CONFIG_SYS_RAMBOOT) && !defined(CONFIG_SYS_INIT_L2_ADDR) +phys_size_t initdram(int board_type) +{ +#if defined(CONFIG_SPD_EEPROM) || defined(CONFIG_DDR_SPD) + return fsl_ddr_sdram_size(); +#else + return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024; +#endif +} +#else /* CONFIG_SYS_RAMBOOT */ phys_size_t initdram(int board_type) { phys_size_t dram_size = 0; @@ -348,6 +358,7 @@ phys_size_t initdram(int board_type) puts("DDR: "); return dram_size; } +#endif /* CONFIG_SYS_RAMBOOT */ #endif #if CONFIG_POST & CONFIG_SYS_POST_MEMORY diff --git a/arch/powerpc/cpu/mpc85xx/cpu_init.c b/arch/powerpc/cpu/mpc85xx/cpu_init.c index 5642cd7b05..6f256cf7a7 100644 --- a/arch/powerpc/cpu/mpc85xx/cpu_init.c +++ b/arch/powerpc/cpu/mpc85xx/cpu_init.c @@ -145,6 +145,22 @@ static void enable_cpc(void) for (i = 0; i < CONFIG_SYS_NUM_CPC; i++, cpc++) { u32 cpccfg0 = in_be32(&cpc->cpccfg0); size += CPC_CFG0_SZ_K(cpccfg0); +#ifdef CONFIG_RAMBOOT_PBL + if (in_be32(&cpc->cpcsrcr0) & CPC_SRCR0_SRAMEN) { + /* find and disable LAW of SRAM */ + struct law_entry law = find_law(CONFIG_SYS_INIT_L3_ADDR); + + if (law.index == -1) { + printf("\nFatal error happened\n"); + return; + } + disable_law(law.index); + + clrbits_be32(&cpc->cpchdbcr0, CPC_HDBCR0_CDQ_SPEC_DIS); + out_be32(&cpc->cpccsr0, 0); + out_be32(&cpc->cpcsrcr0, 0); + } +#endif #ifdef CONFIG_SYS_FSL_ERRATUM_CPC_A002 setbits_be32(&cpc->cpchdbcr0, CPC_HDBCR0_TAG_ECC_SCRUB_DIS); @@ -168,6 +184,9 @@ void invalidate_cpc(void) cpc_corenet_t *cpc = (cpc_corenet_t *)CONFIG_SYS_FSL_CPC_ADDR; for (i = 0; i < CONFIG_SYS_NUM_CPC; i++, cpc++) { + /* skip CPC when it used as all SRAM */ + if (in_be32(&cpc->cpcsrcr0) & CPC_SRCR0_SRAMEN) + continue; /* Flash invalidate the CPC and clear all the locks */ out_be32(&cpc->cpccsr0, CPC_CSR0_FI | CPC_CSR0_LFC); while (in_be32(&cpc->cpccsr0) & (CPC_CSR0_FI | CPC_CSR0_LFC)) diff --git a/arch/powerpc/cpu/mpc85xx/cpu_init_nand.c b/arch/powerpc/cpu/mpc85xx/cpu_init_nand.c index 8fb27abc55..796d398426 100644 --- a/arch/powerpc/cpu/mpc85xx/cpu_init_nand.c +++ b/arch/powerpc/cpu/mpc85xx/cpu_init_nand.c @@ -33,17 +33,15 @@ void cpu_init_f(void) */ out_be32(&lbc->lcrr, LCRR_DBYP | LCRR_CLKDIV_8); -#if defined(CONFIG_NAND_BR_PRELIM) && defined(CONFIG_NAND_OR_PRELIM) - set_lbc_br(0, CONFIG_NAND_BR_PRELIM); - set_lbc_or(0, CONFIG_NAND_OR_PRELIM); +#if defined(CONFIG_SYS_NAND_BR_PRELIM) && defined(CONFIG_SYS_NAND_OR_PRELIM) + set_lbc_br(0, CONFIG_SYS_NAND_BR_PRELIM); + set_lbc_or(0, CONFIG_SYS_NAND_OR_PRELIM); #else -#error CONFIG_NAND_BR_PRELIM, CONFIG_NAND_OR_PRELIM must be defined +#error CONFIG_SYS_NAND_BR_PRELIM, CONFIG_SYS_NAND_OR_PRELIM must be defined #endif #if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L2_ADDR) ccsr_l2cache_t *l2cache = (void *)CONFIG_SYS_MPC85xx_L2_ADDR; - char *l2srbar; - int i; out_be32(&l2cache->l2srbar0, CONFIG_SYS_INIT_L2_ADDR); @@ -54,10 +52,5 @@ void cpu_init_f(void) /* set L2E=1 & L2SRAM=001 */ out_be32(&l2cache->l2ctl, (MPC85xx_L2CTL_L2E | MPC85xx_L2CTL_L2SRAM_ENTIRE)); - - /* Initialize L2 SRAM to zero */ - l2srbar = (char *)CONFIG_SYS_INIT_L2_ADDR; - for (i = 0; i < CONFIG_SYS_L2_SIZE; i++) - l2srbar[i] = 0; #endif } diff --git a/arch/powerpc/cpu/mpc85xx/fsl_corenet_serdes.c b/arch/powerpc/cpu/mpc85xx/fsl_corenet_serdes.c index 7fc00d8c6f..f58d6d617c 100644 --- a/arch/powerpc/cpu/mpc85xx/fsl_corenet_serdes.c +++ b/arch/powerpc/cpu/mpc85xx/fsl_corenet_serdes.c @@ -109,10 +109,13 @@ int serdes_lane_enabled(int lane) return 0; #ifdef CONFIG_SYS_P4080_ERRATUM_SERDES8 - if (!IS_SVR_REV(get_svr(), 1, 0)) - if (bank > 0) - return !(srds_lpd_b[bank] & - (8 >> (lane - (6 + 4 * bank)))); + /* + * For banks two and three, use the srds_lpd_b[] array instead of the + * RCW, because this array contains the real values of SRDS_LPD_B2 and + * SRDS_LPD_B3. + */ + if (bank > 0) + return !(srds_lpd_b[bank] & (8 >> (lane - (6 + 4 * bank)))); #endif return !(in_be32(&gur->rcwsr[word]) & (0x80000000 >> bit)); @@ -303,15 +306,19 @@ void fsl_serdes_init(void) } #ifdef CONFIG_SYS_P4080_ERRATUM_SERDES8 - if (!IS_SVR_REV(get_svr(), 1, 0)) - for (bank = 1; bank < ARRAY_SIZE(srds_lpd_b); bank++) { - sprintf(srds_lpd_opt, "fsl_srds_lpd_b%u", bank + 1); - srds_lpd_arg = hwconfig_subarg_f("serdes", srds_lpd_opt, - &arglen, buf); - if (srds_lpd_arg) - srds_lpd_b[bank] = simple_strtoul(srds_lpd_arg, - NULL, 0); - } + /* + * Store the values of the fsl_srds_lpd_b2 and fsl_srds_lpd_b3 + * hwconfig options into the srds_lpd_b[] array. See README.p4080ds + * for a description of these options. + */ + for (bank = 1; bank < ARRAY_SIZE(srds_lpd_b); bank++) { + sprintf(srds_lpd_opt, "fsl_srds_lpd_b%u", bank + 1); + srds_lpd_arg = + hwconfig_subarg_f("serdes", srds_lpd_opt, &arglen, buf); + if (srds_lpd_arg) + srds_lpd_b[bank] = + simple_strtoul(srds_lpd_arg, NULL, 0) & 0xf; + } #endif /* Look for banks with all lanes disabled, and power down the bank. */ @@ -324,32 +331,12 @@ void fsl_serdes_init(void) } #ifdef CONFIG_SYS_P4080_ERRATUM_SERDES8 - if (IS_SVR_REV(get_svr(), 1, 0)) { - /* At least one bank must be disabled due to SERDES8. If - * no bank is found to be disabled based on lane - * disables, disable bank 3 because we can't turn off its - * lanes in the RCW without disabling MDIO due to erratum - * GEN8. - * - * This means that if you are relying on bank 3 being - * disabled to avoid SERDES8, in some cases you cannot - * also disable all lanes of another bank, or else bank - * 3 won't be disabled, leaving you with a configuration - * that isn't valid according to SERDES8 (e.g. if banks - * 2 and 3 have the same clock, and bank 1 is disabled - * instead of 3). - */ - for (bank = 0; bank < SRDS_MAX_BANK; bank++) { - if (!have_bank[bank]) - break; - } - - if (bank == SRDS_MAX_BANK) - have_bank[FSL_SRDS_BANK_3] = 0; - } else { - if (have_bank[FSL_SRDS_BANK_2]) - have_bank[FSL_SRDS_BANK_3] = 1; - } + /* + * Bank two uses the clock from bank three, so if bank two is enabled, + * then bank three must also be enabled. + */ + if (have_bank[FSL_SRDS_BANK_2]) + have_bank[FSL_SRDS_BANK_3] = 1; #endif for (bank = 0; bank < SRDS_MAX_BANK; bank++) { @@ -455,19 +442,16 @@ void fsl_serdes_init(void) bank = idx; #ifdef CONFIG_SYS_P4080_ERRATUM_SERDES8 - if (!IS_SVR_REV(get_svr(), 1, 0)) { - /* - * Change bank init order to 0, 2, 1, so that the - * third bank's PLL is established before we - * start the second bank which shares the third - * bank's PLL. - */ + /* + * Change bank init order to 0, 2, 1, so that the third bank's + * PLL is established before we start the second bank. The + * second bank uses the third bank's PLL. + */ - if (idx == 1) - bank = FSL_SRDS_BANK_3; - else if (idx == 2) - bank = FSL_SRDS_BANK_2; - } + if (idx == 1) + bank = FSL_SRDS_BANK_3; + else if (idx == 2) + bank = FSL_SRDS_BANK_2; #endif /* Skip disabled banks */ @@ -475,14 +459,18 @@ void fsl_serdes_init(void) continue; #ifdef CONFIG_SYS_P4080_ERRATUM_SERDES8 - if (!IS_SVR_REV(get_svr(), 1, 0)) { - if (idx == 1) { - p4080_erratum_serdes8(srds_regs, gur, - serdes8_devdisr, - serdes8_devdisr2, cfg); - } else if (idx == 2) { - enable_bank(gur, FSL_SRDS_BANK_2); - } + if (idx == 1) { + /* + * Re-enable devices on banks two and three that were + * disabled by the RCW, and then enable bank three. The + * devices need to be enabled before either bank is + * powered up. + */ + p4080_erratum_serdes8(srds_regs, gur, serdes8_devdisr, + serdes8_devdisr2, cfg); + } else if (idx == 2) { + /* Eable bank two now that bank three is enabled. */ + enable_bank(gur, FSL_SRDS_BANK_2); } #endif diff --git a/arch/powerpc/cpu/mpc85xx/speed.c b/arch/powerpc/cpu/mpc85xx/speed.c index e530494102..c4c156d737 100644 --- a/arch/powerpc/cpu/mpc85xx/speed.c +++ b/arch/powerpc/cpu/mpc85xx/speed.c @@ -28,6 +28,7 @@ #include <common.h> #include <ppc_asm.tmpl> +#include <linux/compiler.h> #include <asm/processor.h> #include <asm/io.h> @@ -156,7 +157,7 @@ void get_sys_info (sys_info_t * sysInfo) #endif int i; #ifdef CONFIG_QE - u32 qe_ratio; + __maybe_unused u32 qe_ratio; #endif plat_ratio = (gur->porpllsr) & 0x0000003e; @@ -184,10 +185,15 @@ void get_sys_info (sys_info_t * sysInfo) #endif #ifdef CONFIG_QE +#if defined(CONFIG_P1012) || defined(CONFIG_P1016) || \ + defined(CONFIG_P1021) || defined(CONFIG_P1025) + sysInfo->freqQE = sysInfo->freqSystemBus; +#else qe_ratio = ((gur->porpllsr) & MPC85xx_PORPLLSR_QE_RATIO) >> MPC85xx_PORPLLSR_QE_RATIO_SHIFT; sysInfo->freqQE = qe_ratio * CONFIG_SYS_CLK_FREQ; #endif +#endif #ifdef CONFIG_SYS_DPAA_FMAN sysInfo->freqFMan[0] = sysInfo->freqSystemBus; diff --git a/arch/powerpc/include/asm/config_mpc85xx.h b/arch/powerpc/include/asm/config_mpc85xx.h index 4228161c62..41fd86c4e2 100644 --- a/arch/powerpc/include/asm/config_mpc85xx.h +++ b/arch/powerpc/include/asm/config_mpc85xx.h @@ -88,6 +88,7 @@ #elif defined(CONFIG_P1010) #define CONFIG_MAX_CPUS 1 +#define CONFIG_FSL_SDHC_V2_3 #define CONFIG_SYS_FSL_NUM_LAWS 12 #define CONFIG_TSECV2 #define CONFIG_SYS_FSL_SEC_COMPAT 4 @@ -115,6 +116,9 @@ #define CONFIG_SYS_FSL_SEC_COMPAT 2 #define CONFIG_SYS_FSL_ERRATUM_ELBC_A001 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 +#define QE_MURAM_SIZE 0x6000UL +#define MAX_QE_RISC 1 +#define QE_NUM_OF_SNUM 28 /* P1013 is single core version of P1022 */ #elif defined(CONFIG_P1013) @@ -128,6 +132,7 @@ #elif defined(CONFIG_P1014) #define CONFIG_MAX_CPUS 1 +#define CONFIG_FSL_SDHC_V2_3 #define CONFIG_SYS_FSL_NUM_LAWS 12 #define CONFIG_TSECV2 #define CONFIG_SYS_FSL_SEC_COMPAT 4 @@ -155,6 +160,9 @@ #define CONFIG_SYS_FSL_SEC_COMPAT 2 #define CONFIG_SYS_FSL_ERRATUM_ELBC_A001 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 +#define QE_MURAM_SIZE 0x6000UL +#define MAX_QE_RISC 1 +#define QE_NUM_OF_SNUM 28 /* P1017 is single core version of P1023 */ #elif defined(CONFIG_P1017) @@ -185,6 +193,9 @@ #define CONFIG_SYS_FSL_SEC_COMPAT 2 #define CONFIG_SYS_FSL_ERRATUM_ELBC_A001 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 +#define QE_MURAM_SIZE 0x6000UL +#define MAX_QE_RISC 1 +#define QE_NUM_OF_SNUM 28 #elif defined(CONFIG_P1022) #define CONFIG_MAX_CPUS 2 @@ -225,6 +236,9 @@ #define CONFIG_SYS_FSL_SEC_COMPAT 2 #define CONFIG_SYS_FSL_ERRATUM_ELBC_A001 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 +#define QE_MURAM_SIZE 0x6000UL +#define MAX_QE_RISC 1 +#define QE_NUM_OF_SNUM 28 /* P2010 is single core version of P2020 */ #elif defined(CONFIG_P2010) diff --git a/arch/powerpc/include/asm/fsl_ddr_sdram.h b/arch/powerpc/include/asm/fsl_ddr_sdram.h index 99dddb4f00..127a84039c 100644 --- a/arch/powerpc/include/asm/fsl_ddr_sdram.h +++ b/arch/powerpc/include/asm/fsl_ddr_sdram.h @@ -271,6 +271,7 @@ typedef struct memctl_options_s { } memctl_options_t; extern phys_size_t fsl_ddr_sdram(void); +extern phys_size_t fsl_ddr_sdram_size(void); extern int fsl_use_spd(void); extern void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs, unsigned int ctrl_num); diff --git a/arch/powerpc/include/asm/immap_85xx.h b/arch/powerpc/include/asm/immap_85xx.h index d26d648b13..b51017b550 100644 --- a/arch/powerpc/include/asm/immap_85xx.h +++ b/arch/powerpc/include/asm/immap_85xx.h @@ -1923,7 +1923,31 @@ typedef struct ccsr_gur { #define MPC85xx_PMUXCR_SD_DATA 0x80000000 #define MPC85xx_PMUXCR_SDHC_CD 0x40000000 #define MPC85xx_PMUXCR_SDHC_WP 0x20000000 +#define MPC85xx_PMUXCR_TDM_ENA 0x00800000 +#define MPC85xx_PMUXCR_QE0 0x00008000 +#define MPC85xx_PMUXCR_QE1 0x00004000 +#define MPC85xx_PMUXCR_QE2 0x00002000 +#define MPC85xx_PMUXCR_QE3 0x00001000 +#define MPC85xx_PMUXCR_QE4 0x00000800 +#define MPC85xx_PMUXCR_QE5 0x00000400 +#define MPC85xx_PMUXCR_QE6 0x00000200 +#define MPC85xx_PMUXCR_QE7 0x00000100 +#define MPC85xx_PMUXCR_QE8 0x00000080 +#define MPC85xx_PMUXCR_QE9 0x00000040 +#define MPC85xx_PMUXCR_QE10 0x00000020 +#define MPC85xx_PMUXCR_QE11 0x00000010 +#define MPC85xx_PMUXCR_QE12 0x00000008 +#if defined(CONFIG_P1013) || defined(CONFIG_P1022) +#define MPC85xx_PMUXCR_TDM_MASK 0x0001cc00 +#define MPC85xx_PMUXCR_TDM 0x00014800 +#define MPC85xx_PMUXCR_SPI_MASK 0x00600000 +#define MPC85xx_PMUXCR_SPI 0x00000000 +#endif u32 pmuxcr2; /* Alt. function signal multiplex control 2 */ +#if defined(CONFIG_P1013) || defined(CONFIG_P1022) +#define MPC85xx_PMUXCR2_ETSECUSB_MASK 0x001f1000 +#define MPC85xx_PMUXCR2_USB 0x00150000 +#endif u8 res6[8]; u32 devdisr; /* Device disable control */ #define MPC85xx_DEVDISR_PCI1 0x80000000 @@ -1956,32 +1980,43 @@ typedef struct ccsr_gur { u8 res9[12]; u32 pvr; /* Processor version */ u32 svr; /* System version */ - u8 res10a[8]; + u8 res10[8]; u32 rstcr; /* Reset control */ #if defined(CONFIG_MPC8568)||defined(CONFIG_MPC8569) - u8 res10b[76]; + u8 res11a[76]; par_io_t qe_par_io[7]; - u8 res10c[1600]; + u8 res11b[1600]; +#elif defined(CONFIG_P1012) || defined(CONFIG_P1016) || \ + defined(CONFIG_P1021) || defined(CONFIG_P1025) + u8 res11a[12]; + u32 iovselsr; + u8 res11b[60]; + par_io_t qe_par_io[3]; + u8 res11c[1496]; #else - u8 res10b[1868]; + u8 res11a[1868]; #endif u32 clkdvdr; /* Clock Divide register */ - u8 res10d[1532]; + u8 res12[1532]; u32 clkocr; /* Clock out select */ - u8 res11[12]; + u8 res13[12]; u32 ddrdllcr; /* DDR DLL control */ - u8 res12[12]; + u8 res14[12]; u32 lbcdllcr; /* LBC DLL control */ - u8 res13[248]; + u8 res15[248]; u32 lbiuiplldcr0; /* LBIU PLL Debug Reg 0 */ u32 lbiuiplldcr1; /* LBIU PLL Debug Reg 1 */ u32 ddrioovcr; /* DDR IO Override Control */ u32 tsec12ioovcr; /* eTSEC 1/2 IO override control */ u32 tsec34ioovcr; /* eTSEC 3/4 IO override control */ - u8 res15[61648]; + u8 res16[52]; + u32 sdhcdcr; /* SDHC debug control register */ + u8 res17[61592]; } ccsr_gur_t; #endif +#define SDHCDCR_CD_INV 0x80000000 /* invert SDHC card detect */ + typedef struct serdes_corenet { struct { u32 rstctl; /* Reset Control Register */ diff --git a/board/freescale/corenet_ds/tlb.c b/board/freescale/corenet_ds/tlb.c index 1ae0416248..fe77e798a8 100644 --- a/board/freescale/corenet_ds/tlb.c +++ b/board/freescale/corenet_ds/tlb.c @@ -1,5 +1,5 @@ /* - * Copyright 2008-2010 Freescale Semiconductor, Inc. + * Copyright 2008-2011 Freescale Semiconductor, Inc. * * (C) Copyright 2000 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. @@ -51,9 +51,19 @@ struct fsl_e_tlb_entry tlb_table[] = { /* TLB 1 */ /* *I*** - Covers boot page */ +#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR) + /* + * *I*G - L3SRAM. When L3 is used as 1M SRAM, the address of the + * SRAM is at 0xfff00000, it covered the 0xfffff000. + */ + SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_1M, 1), +#else SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 0, BOOKE_PAGESZ_4K, 1), +#endif /* *I*G* - CCSRBAR */ SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, diff --git a/board/freescale/p1022ds/p1022ds.c b/board/freescale/p1022ds/p1022ds.c index 6f20dc3b9b..8b78404b85 100644 --- a/board/freescale/p1022ds/p1022ds.c +++ b/board/freescale/p1022ds/p1022ds.c @@ -93,11 +93,19 @@ int checkboard(void) /* Choose the 11.2896Mhz codec reference clock */ #define CONFIG_PIXIS_BRDCFG1_AUDCLK_11 0x01 +/* Connect to USB2 */ +#define CONFIG_PIXIS_BRDCFG0_USB2 0x10 +/* Connect to TFM bus */ +#define CONFIG_PIXIS_BRDCFG1_TDM 0x0c +/* Connect to SPI */ +#define CONFIG_PIXIS_BRDCFG0_SPI 0x80 + int misc_init_r(void) { u8 temp; const char *audclk; size_t arglen; + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); /* For DVI, enable the TFP410 Encoder. */ @@ -115,22 +123,48 @@ int misc_init_r(void) return -1; debug("DVI Encoder Read: 0x%02x\n",temp); + /* Enable the USB2 in PMUXCR2 and FGPA */ + if (hwconfig("usb2")) { + clrsetbits_be32(&gur->pmuxcr2, MPC85xx_PMUXCR2_ETSECUSB_MASK, + MPC85xx_PMUXCR2_USB); + setbits_8(&pixis->brdcfg0, CONFIG_PIXIS_BRDCFG0_USB2); + } + + /* tdm and audio can not enable simultaneous*/ + if (hwconfig("tdm") && hwconfig("audclk")){ + printf("WARNING: TDM and AUDIO can not be enabled simultaneous !\n"); + return -1; + } + + /* Enable the TDM in PMUXCR and FGPA */ + if (hwconfig("tdm")) { + clrsetbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_TDM_MASK, + MPC85xx_PMUXCR_TDM); + setbits_8(&pixis->brdcfg1, CONFIG_PIXIS_BRDCFG1_TDM); + /* TDM need some configration option by SPI */ + clrsetbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_SPI_MASK, + MPC85xx_PMUXCR_SPI); + setbits_8(&pixis->brdcfg0, CONFIG_PIXIS_BRDCFG0_SPI); + } + /* * Enable the reference clock for the WM8776 codec, and route the MUX * pins for SSI. The default is the 12.288 MHz clock */ - temp = in_8(&pixis->brdcfg1) & ~(CONFIG_PIXIS_BRDCFG1_SSI_TDM_MASK | - CONFIG_PIXIS_BRDCFG1_AUDCLK_MASK); - temp |= CONFIG_PIXIS_BRDCFG1_SSI_TDM_SSI; - - audclk = hwconfig_arg("audclk", &arglen); - /* Check the first two chars only */ - if (audclk && (strncmp(audclk, "11", 2) == 0)) - temp |= CONFIG_PIXIS_BRDCFG1_AUDCLK_11; - else - temp |= CONFIG_PIXIS_BRDCFG1_AUDCLK_12; - out_8(&pixis->brdcfg1, temp); + if (hwconfig("audclk")) { + temp = in_8(&pixis->brdcfg1) & ~(CONFIG_PIXIS_BRDCFG1_SSI_TDM_MASK | + CONFIG_PIXIS_BRDCFG1_AUDCLK_MASK); + temp |= CONFIG_PIXIS_BRDCFG1_SSI_TDM_SSI; + + audclk = hwconfig_arg("audclk", &arglen); + /* Check the first two chars only */ + if (audclk && (strncmp(audclk, "11", 2) == 0)) + temp |= CONFIG_PIXIS_BRDCFG1_AUDCLK_11; + else + temp |= CONFIG_PIXIS_BRDCFG1_AUDCLK_12; + setbits_8(&pixis->brdcfg1, temp); + } return 0; } diff --git a/boards.cfg b/boards.cfg index 8db62e2c90..a45bd83a15 100644 --- a/boards.cfg +++ b/boards.cfg @@ -545,6 +545,7 @@ P2020RDB_NAND powerpc mpc85xx p1_p2_rdb freesca P2020RDB_SDCARD powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P2020RDB,SDCARD P2020RDB_SPIFLASH powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P2020RDB,SPIFLASH P4080DS powerpc mpc85xx corenet_ds freescale +P4080DS_RAMBOOT_PBL powerpc mpc85xx corenet_ds freescale - P4080DS:RAMBOOT_PBL,SYS_TEXT_BASE=0xFFF80000 mpq101 powerpc mpc85xx mpq101 mercury - mpq101 stxgp3 powerpc mpc85xx stxgp3 stx stxssa powerpc mpc85xx stxssa stx - stxssa diff --git a/doc/README.p1022ds b/doc/README.p1022ds new file mode 100644 index 0000000000..473ecf6217 --- /dev/null +++ b/doc/README.p1022ds @@ -0,0 +1,24 @@ +Overview +-------- +P1022ds is a Low End Dual core platform supporting the P1022 processor +of QorIQ series. P1022 is an e500 based dual core SOC. + + +Pin Multiplex(hwconfig setting) +------------------------------- +Add the environment 'usb2', 'audclk' and 'tdm' to support pin multiplex +via hwconfig, i.e: +'setenv hwconfig usb2' to enable USB2 and disable eTsec2 +'setenv hwconfig tdm' to enable TDM and disable Audio +'setenv hwconfig audclk:12' to enable Audio(codec clock sources is 12MHz) + and disable TDM +'setenv hwconfig 'usb2;tdm' to enable USB2 and TDM, disable eTsec2 and Audio +'setenv hwconfig 'usb2;audclk:11' to enable USB2 and Audio(codec clock sources + is 11MHz), disable eTsec2 and TDM + +Warning: TDM and AUDIO can not enable simultaneous ! +and AUDIO codec clock sources only setting as 11MHz or 12MHz ! +'setenv hwconfig 'audclk:12;tdm' --- error ! +'setenv hwconfig 'audclk:11;tdm' --- error ! +'setenv hwconfig 'audclk:10' --- error ! + diff --git a/doc/README.p4080ds b/doc/README.p4080ds new file mode 100644 index 0000000000..3ed59a8cff --- /dev/null +++ b/doc/README.p4080ds @@ -0,0 +1,32 @@ +Overview +-------- +The P4080DS is a Freescale reference board that hosts the eight-core P4080 SOC. + +SerDes hwconfig configuration +----------------------------- +The P4080 RCW includes three sets of bits the specify which SerDes lanes +should be powered down: SRDS_LPD_B1 (for bank one), SRDS_LPD_B2 (for bank two), +and SRDS_LPD_B3 (for bank three). Each of these contains four bits, one for +each lane in the bank. SerDes Erratum SERDES8 requires that SRDS_LPD_B2 and +SRDS_LPD_B3 be set to 0b1111. This forces banks two and three to be powered +down at reset. + +To re-enable these banks in U-Boot, two hwconfig are available: +"fsl_srds_lpd_b2" and "fsl_srds_lpd_b3". The value passed via fsl_srds_lpd_b2 +is written into SRDS_LPD_B2, and the value passed via fsl_srds_lpd_b3 is into +SRDS_LPD_B3. Each bit represents one of each bank, and a value of '1' +indicates that the lane should be powered down. + +For example, to indicate that both SerDes banks 2 and 3 are powered down, add +the following to hwconfig: + + serdes:fsl_srds_lpd_b2=0xf,fsl_srds_lpd_b3=0xf + +The "0xf" is a mask that corresponds to the 4 lanes A-D. The most significant +bit corresponds to lane A. To indicate that just lane A of bank 3 is to be +powered down, use: + + serdes:fsl_srds_lpd_b3=8 + +These options should be specified only if U-Boot does not automatically power +on the correct lanes. diff --git a/drivers/mmc/fsl_esdhc.c b/drivers/mmc/fsl_esdhc.c index 0962ac4476..4f1b5150c9 100644 --- a/drivers/mmc/fsl_esdhc.c +++ b/drivers/mmc/fsl_esdhc.c @@ -178,14 +178,14 @@ static int esdhc_setup_data(struct mmc *mmc, struct mmc_data *data) wml_value = data->blocksize/4; if (data->flags & MMC_DATA_READ) { - if (wml_value > 0x10) - wml_value = 0x10; + if (wml_value > WML_RD_WML_MAX) + wml_value = WML_RD_WML_MAX_VAL; esdhc_clrsetbits32(®s->wml, WML_RD_WML_MASK, wml_value); esdhc_write32(®s->dsaddr, (u32)data->dest); } else { - if (wml_value > 0x80) - wml_value = 0x80; + if (wml_value > WML_WR_WML_MAX) + wml_value = WML_WR_WML_MAX_VAL; if ((esdhc_read32(®s->prsstat) & PRSSTAT_WPSPL) == 0) { printf("\nThe SD card is locked. Can not write to a locked card.\n\n"); return TIMEOUT; diff --git a/drivers/qe/uec.c b/drivers/qe/uec.c index 282ab23751..811e3fc315 100644 --- a/drivers/qe/uec.c +++ b/drivers/qe/uec.c @@ -1,5 +1,5 @@ /* - * Copyright (C) 2006-2010 Freescale Semiconductor, Inc. + * Copyright (C) 2006-2011 Freescale Semiconductor, Inc. * * Dave Liu <daveliu@freescale.com> * @@ -588,9 +588,27 @@ static void phy_change(struct eth_device *dev) { uec_private_t *uec = (uec_private_t *)dev->priv; +#if defined(CONFIG_P1012) || defined(CONFIG_P1016) || \ + defined(CONFIG_P1021) || defined(CONFIG_P1025) + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + + /* QE9 and QE12 need to be set for enabling QE MII managment signals */ + setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_QE9); + setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_QE12); +#endif + /* Update the link, speed, duplex */ uec->mii_info->phyinfo->read_status(uec->mii_info); +#if defined(CONFIG_P1012) || defined(CONFIG_P1016) || \ + defined(CONFIG_P1021) || defined(CONFIG_P1025) + /* + * QE12 is muxed with LBCTL, it needs to be released for enabling + * LBCTL signal for LBC usage. + */ + clrbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_QE12); +#endif + /* Adjust the interface according to speed */ adjust_link(dev); } @@ -1198,10 +1216,21 @@ static int uec_init(struct eth_device* dev, bd_t *bd) uec_private_t *uec; int err, i; struct phy_info *curphy; +#if defined(CONFIG_P1012) || defined(CONFIG_P1016) || \ + defined(CONFIG_P1021) || defined(CONFIG_P1025) + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); +#endif uec = (uec_private_t *)dev->priv; if (uec->the_first_run == 0) { +#if defined(CONFIG_P1012) || defined(CONFIG_P1016) || \ + defined(CONFIG_P1021) || defined(CONFIG_P1025) + /* QE9 and QE12 need to be set for enabling QE MII managment signals */ + setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_QE9); + setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_QE12); +#endif + err = init_phy(dev); if (err) { printf("%s: Cannot initialize PHY, aborting.\n", @@ -1228,6 +1257,12 @@ static int uec_init(struct eth_device* dev, bd_t *bd) udelay(100000); } while (1); +#if defined(CONFIG_P1012) || defined(CONFIG_P1016) || \ + defined(CONFIG_P1021) || defined(CONFIG_P1025) + /* QE12 needs to be released for enabling LBCTL signal*/ + clrbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_QE12); +#endif + if (err || i <= 0) printf("warning: %s: timeout on PHY link\n", dev->name); diff --git a/include/configs/MPC8536DS.h b/include/configs/MPC8536DS.h index 333a1ea6ce..9b3e032924 100644 --- a/include/configs/MPC8536DS.h +++ b/include/configs/MPC8536DS.h @@ -361,13 +361,13 @@ #define CONFIG_SYS_NAND_U_BOOT_RELOC_SP ((CONFIG_SYS_INIT_L2_END - 1) & ~0xF) /* NAND flash config */ -#define CONFIG_NAND_BR_PRELIM \ +#define CONFIG_SYS_NAND_BR_PRELIM \ (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ | BR_PS_8 /* Port Size = 8 bit */ \ | BR_MS_FCM /* MSEL = FCM */ \ | BR_V) /* valid */ -#define CONFIG_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \ +#define CONFIG_SYS_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \ | OR_FCM_PGS /* Large Page*/ \ | OR_FCM_CSCT \ | OR_FCM_CST \ @@ -377,15 +377,15 @@ | OR_FCM_EHTR) #ifdef CONFIG_RAMBOOT_NAND -#define CONFIG_SYS_BR0_PRELIM CONFIG_NAND_BR_PRELIM /* NAND Base Address */ -#define CONFIG_SYS_OR0_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */ +#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ +#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ #define CONFIG_SYS_BR2_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ #define CONFIG_SYS_OR2_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ #else #define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ #define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ -#define CONFIG_SYS_BR2_PRELIM CONFIG_NAND_BR_PRELIM /* NAND Base Address */ -#define CONFIG_SYS_OR2_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */ +#define CONFIG_SYS_BR2_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ +#define CONFIG_SYS_OR2_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ #endif #define CONFIG_SYS_BR4_PRELIM \ @@ -394,14 +394,14 @@ | BR_PS_8 /* Port Size = 8 bit */ \ | BR_MS_FCM /* MSEL = FCM */ \ | BR_V) /* valid */ -#define CONFIG_SYS_OR4_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */ +#define CONFIG_SYS_OR4_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ #define CONFIG_SYS_BR5_PRELIM \ (BR_PHYS_ADDR((CONFIG_SYS_NAND_BASE_PHYS + 0x80000)) \ | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ | BR_PS_8 /* Port Size = 8 bit */ \ | BR_MS_FCM /* MSEL = FCM */ \ | BR_V) /* valid */ -#define CONFIG_SYS_OR5_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */ +#define CONFIG_SYS_OR5_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ #define CONFIG_SYS_BR6_PRELIM \ (BR_PHYS_ADDR((CONFIG_SYS_NAND_BASE_PHYS + 0xc0000)) \ @@ -409,7 +409,7 @@ | BR_PS_8 /* Port Size = 8 bit */ \ | BR_MS_FCM /* MSEL = FCM */ \ | BR_V) /* valid */ -#define CONFIG_SYS_OR6_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */ +#define CONFIG_SYS_OR6_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ /* Serial Port - controlled on board with jumper J8 * open - index 2 diff --git a/include/configs/MPC8569MDS.h b/include/configs/MPC8569MDS.h index 5f804254fd..5a7e99ee64 100644 --- a/include/configs/MPC8569MDS.h +++ b/include/configs/MPC8569MDS.h @@ -240,12 +240,12 @@ extern unsigned long get_clock_freq(void); #define CONFIG_CMD_NAND 1 #define CONFIG_NAND_FSL_ELBC 1 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) -#define CONFIG_NAND_BR_PRELIM (CONFIG_SYS_NAND_BASE_PHYS \ +#define CONFIG_SYS_NAND_BR_PRELIM (CONFIG_SYS_NAND_BASE_PHYS \ | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ | BR_PS_8 /* Port Size = 8 bit */ \ | BR_MS_FCM /* MSEL = FCM */ \ | BR_V) /* valid */ -#define CONFIG_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \ +#define CONFIG_SYS_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \ | OR_FCM_CSCT \ | OR_FCM_CST \ | OR_FCM_CHT \ @@ -254,15 +254,15 @@ extern unsigned long get_clock_freq(void); | OR_FCM_EHTR) #ifdef CONFIG_RAMBOOT_NAND -#define CONFIG_SYS_BR0_PRELIM CONFIG_NAND_BR_PRELIM /* NAND Base Address */ -#define CONFIG_SYS_OR0_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */ +#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ +#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM/* NAND Options */ #define CONFIG_SYS_BR3_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ #define CONFIG_SYS_OR3_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ #else #define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ #define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ -#define CONFIG_SYS_BR3_PRELIM CONFIG_NAND_BR_PRELIM /* NAND Base Address */ -#define CONFIG_SYS_OR3_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */ +#define CONFIG_SYS_BR3_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ +#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ #endif #define CONFIG_SYS_LBC_LCRR 0x00000004 /* LB clock ratio reg */ diff --git a/include/configs/MPC8572DS.h b/include/configs/MPC8572DS.h index 8c0d06ab86..d93185c8a2 100644 --- a/include/configs/MPC8572DS.h +++ b/include/configs/MPC8572DS.h @@ -362,12 +362,12 @@ /* NAND flash config */ -#define CONFIG_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ +#define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ | BR_PS_8 /* Port Size = 8 bit */ \ | BR_MS_FCM /* MSEL = FCM */ \ | BR_V) /* valid */ -#define CONFIG_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \ +#define CONFIG_SYS_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \ | OR_FCM_PGS /* Large Page*/ \ | OR_FCM_CSCT \ | OR_FCM_CST \ @@ -377,35 +377,35 @@ | OR_FCM_EHTR) #ifdef CONFIG_RAMBOOT_NAND -#define CONFIG_SYS_BR0_PRELIM CONFIG_NAND_BR_PRELIM /* NAND Base Address */ -#define CONFIG_SYS_OR0_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */ +#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ +#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ #define CONFIG_SYS_BR2_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ #define CONFIG_SYS_OR2_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ #else #define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ #define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ -#define CONFIG_SYS_BR2_PRELIM CONFIG_NAND_BR_PRELIM /* NAND Base Address */ -#define CONFIG_SYS_OR2_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */ +#define CONFIG_SYS_BR2_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ +#define CONFIG_SYS_OR2_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ #endif #define CONFIG_SYS_BR4_PRELIM (BR_PHYS_ADDR((CONFIG_SYS_NAND_BASE_PHYS + 0x40000))\ | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ | BR_PS_8 /* Port Size = 8 bit */ \ | BR_MS_FCM /* MSEL = FCM */ \ | BR_V) /* valid */ -#define CONFIG_SYS_OR4_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */ +#define CONFIG_SYS_OR4_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ #define CONFIG_SYS_BR5_PRELIM (BR_PHYS_ADDR((CONFIG_SYS_NAND_BASE_PHYS + 0x80000))\ | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ | BR_PS_8 /* Port Size = 8 bit */ \ | BR_MS_FCM /* MSEL = FCM */ \ | BR_V) /* valid */ -#define CONFIG_SYS_OR5_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */ +#define CONFIG_SYS_OR5_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ #define CONFIG_SYS_BR6_PRELIM (BR_PHYS_ADDR((CONFIG_SYS_NAND_BASE_PHYS + 0xc0000))\ | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ | BR_PS_8 /* Port Size = 8 bit */ \ | BR_MS_FCM /* MSEL = FCM */ \ | BR_V) /* valid */ -#define CONFIG_SYS_OR6_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */ +#define CONFIG_SYS_OR6_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ /* Serial Port - controlled on board with jumper J8 diff --git a/include/configs/P1022DS.h b/include/configs/P1022DS.h index e78bcc54c5..fb2a41ce24 100644 --- a/include/configs/P1022DS.h +++ b/include/configs/P1022DS.h @@ -219,6 +219,22 @@ #undef CONFIG_SYS_FLASH_EMPTY_INFO #endif +#ifndef CONFIG_DIU +#define CONFIG_ATI +#endif + +#ifdef CONFIG_ATI +#define VIDEO_IO_OFFSET CONFIG_SYS_PCIE1_IO_VIRT +#define CONFIG_VIDEO +#define CONFIG_BIOSEMU +#define CONFIG_VIDEO_SW_CURSOR +#define CONFIG_ATI_RADEON_FB +#define CONFIG_VIDEO_LOGO +#define CONFIG_SYS_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET +#define CONFIG_CFB_CONSOLE +#define CONFIG_VGA_AS_SINGLE_DEVICE +#endif + /* * Pass open firmware flat tree */ @@ -492,6 +508,7 @@ "dium=mw e002c01c\0" \ "diuerr=md e002c014 1\0" \ "othbootargs=diufb=15M video=fslfb:1280x1024-32@60,monitor=0 tty0\0" \ + "hwconfig=esdhc;audclk:12\0" \ "monitor=0-DVI\0" #define CONFIG_HDBOOT \ diff --git a/include/configs/P1_P2_RDB.h b/include/configs/P1_P2_RDB.h index 4103e8b96b..cccf84d105 100644 --- a/include/configs/P1_P2_RDB.h +++ b/include/configs/P1_P2_RDB.h @@ -303,13 +303,13 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_NAND_U_BOOT_RELOC_SP ((CONFIG_SYS_INIT_L2_END - 1) & ~0xF) /* NAND flash config */ -#define CONFIG_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ +#define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ | BR_PS_8 /* Port Size = 8 bit */ \ | BR_MS_FCM /* MSEL = FCM */ \ | BR_V) /* valid */ -#define CONFIG_NAND_OR_PRELIM (0xFFF80000 /* length 32K */ \ +#define CONFIG_SYS_NAND_OR_PRELIM (0xFFF80000 /* length 32K */ \ | OR_FCM_CSCT \ | OR_FCM_CST \ | OR_FCM_CHT \ @@ -318,15 +318,15 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); | OR_FCM_EHTR) #ifdef CONFIG_RAMBOOT_NAND -#define CONFIG_SYS_BR0_PRELIM CONFIG_NAND_BR_PRELIM /* NAND Base Address */ -#define CONFIG_SYS_OR0_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */ +#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ +#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ #define CONFIG_SYS_BR1_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ #define CONFIG_SYS_OR1_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ #else #define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ #define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ -#define CONFIG_SYS_BR1_PRELIM CONFIG_NAND_BR_PRELIM /* NAND Base Address */ -#define CONFIG_SYS_OR1_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */ +#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ +#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ #endif #define CONFIG_SYS_VSC7385_BASE 0xffb00000 diff --git a/include/configs/P2020DS.h b/include/configs/P2020DS.h index 30da7b1d45..47f1f18006 100644 --- a/include/configs/P2020DS.h +++ b/include/configs/P2020DS.h @@ -326,12 +326,12 @@ #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) /* NAND flash config */ -#define CONFIG_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ +#define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ | BR_PS_8 /* Port Size = 8bit */ \ | BR_MS_FCM /* MSEL = FCM */ \ | BR_V) /* valid */ -#define CONFIG_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \ +#define CONFIG_SYS_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \ | OR_FCM_PGS /* Large Page*/ \ | OR_FCM_CSCT \ | OR_FCM_CST \ @@ -342,28 +342,28 @@ #define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ #define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ -#define CONFIG_SYS_BR2_PRELIM CONFIG_NAND_BR_PRELIM /* NAND Base Address */ -#define CONFIG_SYS_OR2_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */ +#define CONFIG_SYS_BR2_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ +#define CONFIG_SYS_OR2_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ #define CONFIG_SYS_BR4_PRELIM (BR_PHYS_ADDR((CONFIG_SYS_NAND_BASE_PHYS + 0x40000))\ | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ | BR_PS_8 /* Port Size = 8bit */ \ | BR_MS_FCM /* MSEL = FCM */ \ | BR_V) /* valid */ -#define CONFIG_SYS_OR4_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */ +#define CONFIG_SYS_OR4_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ #define CONFIG_SYS_BR5_PRELIM (BR_PHYS_ADDR((CONFIG_SYS_NAND_BASE_PHYS + 0x80000))\ | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ | BR_PS_8 /* Port Size = 8bit */ \ | BR_MS_FCM /* MSEL = FCM */ \ | BR_V) /* valid */ -#define CONFIG_SYS_OR5_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */ +#define CONFIG_SYS_OR5_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ #define CONFIG_SYS_BR6_PRELIM (BR_PHYS_ADDR((CONFIG_SYS_NAND_BASE_PHYS + 0xc0000))\ | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ | BR_PS_8 /* Port Size = 8bit */ \ | BR_MS_FCM /* MSEL = FCM */ \ | BR_V) /* valid */ -#define CONFIG_SYS_OR6_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */ +#define CONFIG_SYS_OR6_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ /* Serial Port - controlled on board with jumper J8 * open - index 2 diff --git a/include/configs/corenet_ds.h b/include/configs/corenet_ds.h index 7bafa05b19..4e2b3fb983 100644 --- a/include/configs/corenet_ds.h +++ b/include/configs/corenet_ds.h @@ -28,6 +28,11 @@ #include "../board/freescale/common/ics307_clk.h" +#ifdef CONFIG_RAMBOOT_PBL +#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE +#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc +#endif + /* High Level Configuration Options */ #define CONFIG_BOOKE #define CONFIG_E500 /* BOOKE e500 family */ @@ -63,12 +68,17 @@ #define CONFIG_ENV_OVERWRITE +#if defined(CONFIG_RAMBOOT_PBL) + #define CONFIG_SYS_NO_FLASH /* Store ENV in memory only */ +#endif + #ifdef CONFIG_SYS_NO_FLASH #define CONFIG_ENV_IS_NOWHERE #else #define CONFIG_ENV_IS_IN_FLASH #define CONFIG_FLASH_CFI_DRIVER #define CONFIG_SYS_FLASH_CFI +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) #endif #define CONFIG_SYS_CLK_FREQ get_board_sys_clk() /* sysclk for MPC85xx */ @@ -100,6 +110,18 @@ #define CONFIG_PANIC_HANG /* do not reset board on panic */ /* + * Config the L3 Cache as L3 SRAM + */ +#define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_INIT_L3_ADDR_PHYS (0xf00000000ull | CONFIG_RAMBOOT_TEXT_BASE) +#else +#define CONFIG_SYS_INIT_L3_ADDR_PHYS CONFIG_SYS_INIT_L3_ADDR +#endif +#define CONFIG_SYS_L3_SIZE (1024 << 10) +#define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE) + +/* * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) */ @@ -192,6 +214,10 @@ #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ +#if defined(CONFIG_RAMBOOT_PBL) +#define CONFIG_SYS_RAMBOOT +#endif + #define CONFIG_SYS_FLASH_EMPTY_INFO #define CONFIG_SYS_FLASH_AMD_CHECK_DQ7 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS} @@ -390,33 +416,10 @@ #endif #ifdef CONFIG_PCI - -/*PCIE video card used*/ -#define VIDEO_IO_OFFSET CONFIG_SYS_PCIE1_IO_VIRT - -/* video */ -#define CONFIG_VIDEO - -#ifdef CONFIG_VIDEO -#define CONFIG_BIOSEMU -#define CONFIG_CFB_CONSOLE -#define CONFIG_VIDEO_SW_CURSOR -#define CONFIG_VGA_AS_SINGLE_DEVICE -#define CONFIG_ATI_RADEON_FB -#define CONFIG_VIDEO_LOGO -#define CONFIG_SYS_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET -#endif - #define CONFIG_NET_MULTI #define CONFIG_PCI_PNP /* do pci plug-and-play */ #define CONFIG_E1000 -#ifndef CONFIG_PCI_PNP -#define PCI_ENET0_IOADDR CONFIG_SYS_PCI1_IO_BUS -#define PCI_ENET0_MEMADDR CONFIG_SYS_PCI1_IO_BUS -#define PCI_IDSEL_NUMBER 0x11 /* IDSEL = AD11 */ -#endif - #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ #define CONFIG_DOS_PARTITION #endif /* CONFIG_PCI */ @@ -462,7 +465,6 @@ /* * Environment */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) #define CONFIG_ENV_SIZE 0x2000 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ diff --git a/include/fsl_esdhc.h b/include/fsl_esdhc.h index 477bbd792e..8418bf7f47 100644 --- a/include/fsl_esdhc.h +++ b/include/fsl_esdhc.h @@ -2,7 +2,7 @@ * FSL SD/MMC Defines *------------------------------------------------------------------- * - * Copyright 2007-2008,2010 Freescale Semiconductor, Inc + * Copyright 2007-2008,2010-2011 Freescale Semiconductor, Inc * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as @@ -135,8 +135,21 @@ #define WML 0x2e044 #define WML_WRITE 0x00010000 +#ifdef CONFIG_FSL_SDHC_V2_3 +#define WML_RD_WML_MAX 0x80 +#define WML_WR_WML_MAX 0x80 +#define WML_RD_WML_MAX_VAL 0x0 +#define WML_WR_WML_MAX_VAL 0x0 +#define WML_RD_WML_MASK 0x7f +#define WML_WR_WML_MASK 0x7f0000 +#else +#define WML_RD_WML_MAX 0x10 +#define WML_WR_WML_MAX 0x80 +#define WML_RD_WML_MAX_VAL 0x10 +#define WML_WR_WML_MAX_VAL 0x80 #define WML_RD_WML_MASK 0xff #define WML_WR_WML_MASK 0xff0000 +#endif #define BLKATTR 0x2e004 #define BLKATTR_CNT(x) ((x & 0xffff) << 16) |