diff options
| -rw-r--r-- | board/csb226/Makefile | 10 | ||||
| -rw-r--r-- | board/csb226/config.mk | 15 | ||||
| -rw-r--r-- | board/csb226/csb226.c | 22 | ||||
| -rw-r--r-- | board/csb226/lowlevel_init.S | 437 | ||||
| -rw-r--r-- | include/configs/csb226.h | 4 |
5 files changed, 18 insertions, 470 deletions
diff --git a/board/csb226/Makefile b/board/csb226/Makefile index c12dbea9cd..5e1332bae4 100644 --- a/board/csb226/Makefile +++ b/board/csb226/Makefile @@ -26,17 +26,15 @@ include $(TOPDIR)/config.mk LIB = $(obj)lib$(BOARD).a COBJS := csb226.o flash.o -SOBJS := lowlevel_init.o -SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +SRCS := $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(COBJS)) -SOBJS := $(addprefix $(obj),$(SOBJS)) -$(LIB): $(obj).depend $(OBJS) $(SOBJS) - $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS) +$(LIB): $(obj).depend $(OBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) clean: - rm -f $(SOBJS) $(OBJS) + rm -f $(OBJS) distclean: clean rm -f $(LIB) core *.bak $(obj).depend diff --git a/board/csb226/config.mk b/board/csb226/config.mk deleted file mode 100644 index 9e4655585d..0000000000 --- a/board/csb226/config.mk +++ /dev/null @@ -1,15 +0,0 @@ -# -# Linux-Kernel is expected to be at c000'8000, entry c000'8000 -# -# we load ourself to c170'0000, the upper 1 MB of second bank -# -# download areas is c800'0000 -# - -# This is the address where U-Boot lives in flash: -#CONFIG_SYS_TEXT_BASE = 0 - -# FIXME: armboot does only work correctly when being compiled -# for the addresses _after_ relocation to RAM!! Otherwhise the -# .bss segment is assumed in flash... -CONFIG_SYS_TEXT_BASE = 0xa1fe0000 diff --git a/board/csb226/csb226.c b/board/csb226/csb226.c index 6eed9ad676..dd29e62659 100644 --- a/board/csb226/csb226.c +++ b/board/csb226/csb226.c @@ -69,8 +69,9 @@ int misc_init_r(void) int board_init (void) { - /* memory and cpu-speed are setup before relocation */ - /* so we do _nothing_ here */ + /* We have RAM, disable cache */ + dcache_disable(); + icache_disable(); /* arch number of CSB226 board */ gd->bd->bi_arch_number = MACH_TYPE_CSB226; @@ -82,21 +83,20 @@ int board_init (void) } -/** - * dram_init: - setup dynamic RAM - * - * @return: 0 in case of success - */ +extern void pxa_dram_init(void); +int dram_init(void) +{ + pxa_dram_init(); + gd->ram_size = PHYS_SDRAM_1_SIZE; + return 0; +} -int dram_init (void) +void dram_init_banksize(void) { gd->bd->bi_dram[0].start = PHYS_SDRAM_1; gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE; - - return 0; } - /** * csb226_set_led: - switch LEDs on or off * diff --git a/board/csb226/lowlevel_init.S b/board/csb226/lowlevel_init.S deleted file mode 100644 index 55169be45e..0000000000 --- a/board/csb226/lowlevel_init.S +++ /dev/null @@ -1,437 +0,0 @@ -/* - * Most of this taken from Redboot hal_platform_setup.h with cleanup - * - * NOTE: I haven't clean this up considerably, just enough to get it - * running. See hal_platform_setup.h for the source. See - * board/cradle/lowlevel_init.S for another PXA250 setup that is - * much cleaner. - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#include <config.h> -#include <version.h> -#include <asm/arch/pxa-regs.h> - -DRAM_SIZE: .long CONFIG_SYS_DRAM_SIZE - -/* wait for coprocessor write complete */ - .macro CPWAIT reg - mrc p15,0,\reg,c2,c0,0 - mov \reg,\reg - sub pc,pc,#4 - .endm - -_TEXT_BASE: - .word CONFIG_SYS_TEXT_BASE - - -/* - * Memory setup - */ - -.globl lowlevel_init -lowlevel_init: - - mov r10, lr - - /* Set up GPIO pins first ----------------------------------------- */ - - ldr r0, =GPSR0 - ldr r1, =CONFIG_SYS_GPSR0_VAL - str r1, [r0] - - ldr r0, =GPSR1 - ldr r1, =CONFIG_SYS_GPSR1_VAL - str r1, [r0] - - ldr r0, =GPSR2 - ldr r1, =CONFIG_SYS_GPSR2_VAL - str r1, [r0] - - ldr r0, =GPCR0 - ldr r1, =CONFIG_SYS_GPCR0_VAL - str r1, [r0] - - ldr r0, =GPCR1 - ldr r1, =CONFIG_SYS_GPCR1_VAL - str r1, [r0] - - ldr r0, =GPCR2 - ldr r1, =CONFIG_SYS_GPCR2_VAL - str r1, [r0] - - ldr r0, =GPDR0 - ldr r1, =CONFIG_SYS_GPDR0_VAL - str r1, [r0] - - ldr r0, =GPDR1 - ldr r1, =CONFIG_SYS_GPDR1_VAL - str r1, [r0] - - ldr r0, =GPDR2 - ldr r1, =CONFIG_SYS_GPDR2_VAL - str r1, [r0] - - ldr r0, =GAFR0_L - ldr r1, =CONFIG_SYS_GAFR0_L_VAL - str r1, [r0] - - ldr r0, =GAFR0_U - ldr r1, =CONFIG_SYS_GAFR0_U_VAL - str r1, [r0] - - ldr r0, =GAFR1_L - ldr r1, =CONFIG_SYS_GAFR1_L_VAL - str r1, [r0] - - ldr r0, =GAFR1_U - ldr r1, =CONFIG_SYS_GAFR1_U_VAL - str r1, [r0] - - ldr r0, =GAFR2_L - ldr r1, =CONFIG_SYS_GAFR2_L_VAL - str r1, [r0] - - ldr r0, =GAFR2_U - ldr r1, =CONFIG_SYS_GAFR2_U_VAL - str r1, [r0] - - ldr r0, =PSSR /* enable GPIO pins */ - ldr r1, =CONFIG_SYS_PSSR_VAL - str r1, [r0] - -/* ldr r3, =MSC1 / low - bank 2 Lubbock Registers / SRAM */ -/* ldr r2, =CONFIG_SYS_MSC1_VAL / high - bank 3 Ethernet Controller */ -/* str r2, [r3] / need to set MSC1 before trying to write to the HEX LEDs */ -/* ldr r2, [r3] / need to read it back to make sure the value latches (see MSC section of manual) */ -/* */ -/* ldr r1, =LED_BLANK */ -/* mov r0, #0xFF */ -/* str r0, [r1] / turn on hex leds */ -/* */ -/*loop: */ -/* */ -/* ldr r0, =0xB0070001 */ -/* ldr r1, =_LED */ -/* str r0, [r1] / hex display */ - - - /* ---------------------------------------------------------------- */ - /* Enable memory interface */ - /* */ - /* The sequence below is based on the recommended init steps */ - /* detailed in the Intel PXA250 Operating Systems Developers Guide, */ - /* Chapter 10. */ - /* ---------------------------------------------------------------- */ - - /* ---------------------------------------------------------------- */ - /* Step 1: Wait for at least 200 microsedonds to allow internal */ - /* clocks to settle. Only necessary after hard reset... */ - /* FIXME: can be optimized later */ - /* ---------------------------------------------------------------- */ - - ldr r3, =OSCR /* reset the OS Timer Count to zero */ - mov r2, #0 - str r2, [r3] - ldr r4, =0x300 /* really 0x2E1 is about 200usec, */ - /* so 0x300 should be plenty */ -1: - ldr r2, [r3] - cmp r4, r2 - bgt 1b - -mem_init: - - ldr r1, =MEMC_BASE /* get memory controller base addr. */ - - /* ---------------------------------------------------------------- */ - /* Step 2a: Initialize Asynchronous static memory controller */ - /* ---------------------------------------------------------------- */ - - /* MSC registers: timing, bus width, mem type */ - - /* MSC0: nCS(0,1) */ - ldr r2, =CONFIG_SYS_MSC0_VAL - str r2, [r1, #MSC0_OFFSET] - ldr r2, [r1, #MSC0_OFFSET] /* read back to ensure */ - /* that data latches */ - /* MSC1: nCS(2,3) */ - ldr r2, =CONFIG_SYS_MSC1_VAL - str r2, [r1, #MSC1_OFFSET] - ldr r2, [r1, #MSC1_OFFSET] - - /* MSC2: nCS(4,5) */ - ldr r2, =CONFIG_SYS_MSC2_VAL - str r2, [r1, #MSC2_OFFSET] - ldr r2, [r1, #MSC2_OFFSET] - - /* ---------------------------------------------------------------- */ - /* Step 2b: Initialize Card Interface */ - /* ---------------------------------------------------------------- */ - - /* MECR: Memory Expansion Card Register */ - ldr r2, =CONFIG_SYS_MECR_VAL - str r2, [r1, #MECR_OFFSET] - ldr r2, [r1, #MECR_OFFSET] - - /* MCMEM0: Card Interface slot 0 timing */ - ldr r2, =CONFIG_SYS_MCMEM0_VAL - str r2, [r1, #MCMEM0_OFFSET] - ldr r2, [r1, #MCMEM0_OFFSET] - - /* MCMEM1: Card Interface slot 1 timing */ - ldr r2, =CONFIG_SYS_MCMEM1_VAL - str r2, [r1, #MCMEM1_OFFSET] - ldr r2, [r1, #MCMEM1_OFFSET] - - /* MCATT0: Card Interface Attribute Space Timing, slot 0 */ - ldr r2, =CONFIG_SYS_MCATT0_VAL - str r2, [r1, #MCATT0_OFFSET] - ldr r2, [r1, #MCATT0_OFFSET] - - /* MCATT1: Card Interface Attribute Space Timing, slot 1 */ - ldr r2, =CONFIG_SYS_MCATT1_VAL - str r2, [r1, #MCATT1_OFFSET] - ldr r2, [r1, #MCATT1_OFFSET] - - /* MCIO0: Card Interface I/O Space Timing, slot 0 */ - ldr r2, =CONFIG_SYS_MCIO0_VAL - str r2, [r1, #MCIO0_OFFSET] - ldr r2, [r1, #MCIO0_OFFSET] - - /* MCIO1: Card Interface I/O Space Timing, slot 1 */ - ldr r2, =CONFIG_SYS_MCIO1_VAL - str r2, [r1, #MCIO1_OFFSET] - ldr r2, [r1, #MCIO1_OFFSET] - - /* ---------------------------------------------------------------- */ - /* Step 2c: Write FLYCNFG FIXME: what's that??? */ - /* ---------------------------------------------------------------- */ - - /* test if we run from flash or RAM - RAM/BDI: don't setup RAM */ - adr r3, mem_init /* r0 <- current position of code */ - ldr r2, =mem_init - cmp r3, r2 /* skip init if in place */ - beq initirqs - - - /* ---------------------------------------------------------------- */ - /* Step 2d: Initialize Timing for Sync Memory (SDCLK0) */ - /* ---------------------------------------------------------------- */ - - /* Before accessing MDREFR we need a valid DRI field, so we set */ - /* this to power on defaults + DRI field. */ - - ldr r3, =CONFIG_SYS_MDREFR_VAL - ldr r2, =0xFFF - and r3, r3, r2 - ldr r4, =0x03ca4000 - orr r4, r4, r3 - - str r4, [r1, #MDREFR_OFFSET] /* write back MDREFR */ - ldr r4, [r1, #MDREFR_OFFSET] - - - /* ---------------------------------------------------------------- */ - /* Step 3: Initialize Synchronous Static Memory (Flash/Peripherals) */ - /* ---------------------------------------------------------------- */ - - /* Initialize SXCNFG register. Assert the enable bits */ - - /* Write SXMRS to cause an MRS command to all enabled banks of */ - /* synchronous static memory. Note that SXLCR need not be written */ - /* at this time. */ - - /* FIXME: we use async mode for now */ - - - /* ---------------------------------------------------------------- */ - /* Step 4: Initialize SDRAM */ - /* ---------------------------------------------------------------- */ - - /* Step 4a: assert MDREFR:K?RUN and configure */ - /* MDREFR:K1DB2 and MDREFR:K2DB2 as desired. */ - - ldr r4, =CONFIG_SYS_MDREFR_VAL - str r4, [r1, #MDREFR_OFFSET] /* write back MDREFR */ - ldr r4, [r1, #MDREFR_OFFSET] - - /* Step 4b: de-assert MDREFR:SLFRSH. */ - - bic r4, r4, #(MDREFR_SLFRSH) - - str r4, [r1, #MDREFR_OFFSET] /* write back MDREFR */ - ldr r4, [r1, #MDREFR_OFFSET] - - - /* Step 4c: assert MDREFR:E1PIN and E0PIO */ - - orr r4, r4, #(MDREFR_E1PIN|MDREFR_E0PIN) - - str r4, [r1, #MDREFR_OFFSET] /* write back MDREFR */ - ldr r4, [r1, #MDREFR_OFFSET] - - - /* Step 4d: write MDCNFG with MDCNFG:DEx deasserted (set to 0), to */ - /* configure but not enable each SDRAM partition pair. */ - - ldr r4, =CONFIG_SYS_MDCNFG_VAL - bic r4, r4, #(MDCNFG_DE0|MDCNFG_DE1) - - str r4, [r1, #MDCNFG_OFFSET] /* write back MDCNFG */ - ldr r4, [r1, #MDCNFG_OFFSET] - - - /* Step 4e: Wait for the clock to the SDRAMs to stabilize, */ - /* 100..200 µsec. */ - - ldr r3, =OSCR /* reset the OS Timer Count to zero */ - mov r2, #0 - str r2, [r3] - ldr r4, =0x300 /* really 0x2E1 is about 200usec, */ - /* so 0x300 should be plenty */ -1: - ldr r2, [r3] - cmp r4, r2 - bgt 1b - - - /* Step 4f: Trigger a number (usually 8) refresh cycles by */ - /* attempting non-burst read or write accesses to disabled */ - /* SDRAM, as commonly specified in the power up sequence */ - /* documented in SDRAM data sheets. The address(es) used */ - /* for this purpose must not be cacheable. */ - - /* There should 9 writes, since the first write doesn't */ - /* trigger a refresh cycle on PXA250. See Intel PXA250 and */ - /* PXA210 Processors Specification Update, */ - /* Jan 2003, Errata #116, page 30. */ - - - ldr r3, =CONFIG_SYS_DRAM_BASE - str r2, [r3] - str r2, [r3] - str r2, [r3] - str r2, [r3] - str r2, [r3] - str r2, [r3] - str r2, [r3] - str r2, [r3] - str r2, [r3] - - /* Step 4g: Write MDCNFG with enable bits asserted */ - /* (MDCNFG:DEx set to 1). */ - - ldr r3, [r1, #MDCNFG_OFFSET] - orr r3, r3, #(MDCNFG_DE0|MDCNFG_DE1) - str r3, [r1, #MDCNFG_OFFSET] - - /* Step 4h: Write MDMRS. */ - - ldr r2, =CONFIG_SYS_MDMRS_VAL - str r2, [r1, #MDMRS_OFFSET] - - - /* We are finished with Intel's memory controller initialisation */ - - /* ---------------------------------------------------------------- */ - /* Disable (mask) all interrupts at interrupt controller */ - /* ---------------------------------------------------------------- */ - -initirqs: - - mov r1, #0 /* clear int. level register (IRQ, not FIQ) */ - ldr r2, =ICLR - str r1, [r2] - - ldr r2, =ICMR /* mask all interrupts at the controller */ - str r1, [r2] - - - /* ---------------------------------------------------------------- */ - /* Clock initialisation */ - /* ---------------------------------------------------------------- */ - -initclks: - - /* Disable the peripheral clocks, and set the core clock frequency */ - /* (hard-coding at 398.12MHz for now). */ - - /* Turn Off ALL on-chip peripheral clocks for re-configuration */ - /* Note: See label 'ENABLECLKS' for the re-enabling */ - ldr r1, =CKEN - mov r2, #0 - str r2, [r1] - - - /* default value in case no valid rotary switch setting is found */ - ldr r2, =(CCCR_L27|CCCR_M2|CCCR_N10) /* DEFAULT: {200/200/100} */ - - /* ... and write the core clock config register */ - ldr r1, =CCCR - str r2, [r1] - - /* enable the 32Khz oscillator for RTC and PowerManager */ -/* - ldr r1, =OSCC - mov r2, #OSCC_OON - str r2, [r1] -*/ - /* NOTE: spin here until OSCC.OOK get set, meaning the PLL */ - /* has settled. */ -60: - ldr r2, [r1] - ands r2, r2, #1 - beq 60b - - /* ---------------------------------------------------------------- */ - /* */ - /* ---------------------------------------------------------------- */ - - /* Save SDRAM size */ - ldr r1, =DRAM_SIZE - str r8, [r1] - - /* Interrupt init: Mask all interrupts */ - ldr r0, =ICMR /* enable no sources */ - mov r1, #0 - str r1, [r0] - - /* FIXME */ - -#ifndef DEBUG - /*Disable software and data breakpoints */ - mov r0,#0 - mcr p15,0,r0,c14,c8,0 /* ibcr0 */ - mcr p15,0,r0,c14,c9,0 /* ibcr1 */ - mcr p15,0,r0,c14,c4,0 /* dbcon */ - - /*Enable all debug functionality */ - mov r0,#0x80000000 - mcr p14,0,r0,c10,c0,0 /* dcsr */ -#endif - - /* ---------------------------------------------------------------- */ - /* End lowlevel_init */ - /* ---------------------------------------------------------------- */ - -endlowlevel_init: - - mov pc, lr diff --git a/include/configs/csb226.h b/include/configs/csb226.h index 169ec34771..72e47ce7a8 100644 --- a/include/configs/csb226.h +++ b/include/configs/csb226.h @@ -45,7 +45,7 @@ /* we will never enable dcache, because we have to setup MMU first */ #define CONFIG_SYS_NO_DCACHE - +#define CONFIG_SYS_TEXT_BASE 0x0 /* * Hardware drivers */ @@ -471,6 +471,8 @@ #define CONFIG_SYS_MDCNFG_VAL 0x09a909a9 #define CONFIG_SYS_MDREFR_VAL 0x038ff030 #define CONFIG_SYS_MDMRS_VAL 0x00220022 +#define CONFIG_SYS_FLYCNFG_VAL 0x00000000 +#define CONFIG_SYS_SXCNFG_VAL 0x00000000 /* * PCMCIA and CF Interfaces |