diff options
477 files changed, 1198 insertions, 4323 deletions
@@ -2204,52 +2204,7 @@ The following options need to be configured: If you do not have i2c muxes on your board, omit this define. -- Legacy I2C Support: CONFIG_HARD_I2C - - NOTE: It is intended to move drivers to CONFIG_SYS_I2C which - provides the following compelling advantages: - - - more than one i2c adapter is usable - - approved multibus support - - better i2c mux support - - ** Please consider updating your I2C driver now. ** - - These enable legacy I2C serial bus commands. Defining - CONFIG_HARD_I2C will include the appropriate I2C driver - for the selected CPU. - - This will allow you to use i2c commands at the u-boot - command line (as long as you set CONFIG_CMD_I2C in - CONFIG_COMMANDS) and communicate with i2c based realtime - clock chips. See common/cmd_i2c.c for a description of the - command line interface. - - CONFIG_HARD_I2C selects a hardware I2C controller. - - There are several other quantities that must also be - defined when you define CONFIG_HARD_I2C. - - In both cases you will need to define CONFIG_SYS_I2C_SPEED - to be the frequency (in Hz) at which you wish your i2c bus - to run and CONFIG_SYS_I2C_SLAVE to be the address of this node (ie - the CPU's i2c node address). - - Now, the u-boot i2c code for the mpc8xx - (arch/powerpc/cpu/mpc8xx/i2c.c) sets the CPU up as a master node - and so its address should therefore be cleared to 0 (See, - eg, MPC823e User's Manual p.16-473). So, set - CONFIG_SYS_I2C_SLAVE to 0. - - CONFIG_SYS_I2C_INIT_MPC5XXX - - When a board is reset during an i2c bus transfer - chips might think that the current transfer is still - in progress. Reset the slave devices by sending start - commands until the slave device responds. - - That's all that's required for CONFIG_HARD_I2C. - +- Legacy I2C Support: If you use the software i2c interface (CONFIG_SYS_I2C_SOFT) then the following macros need to be defined (examples are from include/configs/lwmon.h): @@ -2338,23 +2293,6 @@ The following options need to be configured: custom i2c_init_board() routine in boards/xxx/board.c is run early in the boot sequence. - CONFIG_SYS_I2C_BOARD_LATE_INIT - - An alternative to CONFIG_SYS_I2C_INIT_BOARD. If this option is - defined a custom i2c_board_late_init() routine in - boards/xxx/board.c is run AFTER the operations in i2c_init() - is completed. This callpoint can be used to unreset i2c bus - using CPU i2c controller register accesses for CPUs whose i2c - controller provide such a method. It is called at the end of - i2c_init() to allow i2c_init operations to setup the i2c bus - controller on the CPU (e.g. setting bus speed & slave address). - - CONFIG_I2CFAST (PPC405GP|PPC405EP only) - - This option enables configuration of bi_iic_fast[] flags - in u-boot bd_info structure based on u-boot environment - variable "i2cfast". (see also i2cfast) - CONFIG_I2C_MULTI_BUS This option allows the use of multiple I2C buses, each of which @@ -3708,11 +3646,6 @@ Configuration Settings: If defined, don't allow the -f switch to env set override variable access flags. -- CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC (OMAP only) - This is set by OMAP boards for the max time that reset should - be asserted. See doc/README.omap-reset-time for details on how - the value can be calculated on a given board. - - CONFIG_USE_STDINT If stdint.h is available with your toolchain you can define this option to enable it. You can provide option 'USE_STDINT=1' when diff --git a/arch/Kconfig b/arch/Kconfig index 160accdbcb..826e346f98 100644 --- a/arch/Kconfig +++ b/arch/Kconfig @@ -84,6 +84,7 @@ config X86 select DM_GPIO select DM_SPI select DM_SPI_FLASH + select USB_EHCI_HCD config XTENSA bool "Xtensa architecture" diff --git a/arch/arm/cpu/arm926ejs/omap/Makefile b/arch/arm/cpu/arm926ejs/omap/Makefile deleted file mode 100644 index add923276c..0000000000 --- a/arch/arm/cpu/arm926ejs/omap/Makefile +++ /dev/null @@ -1,10 +0,0 @@ -# -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y = timer.o -obj-$(CONFIG_DISPLAY_CPUINFO) += cpuinfo.o -obj-y += reset.o diff --git a/arch/arm/cpu/arm926ejs/omap/cpuinfo.c b/arch/arm/cpu/arm926ejs/omap/cpuinfo.c deleted file mode 100644 index 587d99a2bb..0000000000 --- a/arch/arm/cpu/arm926ejs/omap/cpuinfo.c +++ /dev/null @@ -1,242 +0,0 @@ -/* - * OMAP1 CPU identification code - * - * Copyright (C) 2004 Nokia Corporation - * Written by Tony Lindgren <tony@atomide.com> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ - -#include <common.h> -#include <command.h> -#include <linux/compiler.h> - -#if defined(CONFIG_OMAP) - -#define omap_readw(x) *(volatile unsigned short *)(x) -#define omap_readl(x) *(volatile unsigned long *)(x) - -#define OMAP_DIE_ID_0 0xfffe1800 -#define OMAP_DIE_ID_1 0xfffe1804 -#define OMAP_PRODUCTION_ID_0 0xfffe2000 -#define OMAP_PRODUCTION_ID_1 0xfffe2004 -#define OMAP32_ID_0 0xfffed400 -#define OMAP32_ID_1 0xfffed404 - -struct omap_id { - u16 jtag_id; /* Used to determine OMAP type */ - u8 die_rev; /* Processor revision */ - u32 omap_id; /* OMAP revision */ - u32 type; /* Cpu id bits [31:08], cpu class bits [07:00] */ -}; - -/* Register values to detect the OMAP version */ -static struct omap_id omap_ids[] = { - { .jtag_id = 0xb574, .die_rev = 0x2, .omap_id = 0x03310315, .type = 0x03100000}, - { .jtag_id = 0x355f, .die_rev = 0x0, .omap_id = 0x03320000, .type = 0x07300100}, - { .jtag_id = 0xb55f, .die_rev = 0x0, .omap_id = 0x03320000, .type = 0x07300300}, - { .jtag_id = 0xb470, .die_rev = 0x0, .omap_id = 0x03310100, .type = 0x15100000}, - { .jtag_id = 0xb576, .die_rev = 0x0, .omap_id = 0x03320000, .type = 0x16100000}, - { .jtag_id = 0xb576, .die_rev = 0x2, .omap_id = 0x03320100, .type = 0x16110000}, - { .jtag_id = 0xb576, .die_rev = 0x3, .omap_id = 0x03320100, .type = 0x16100c00}, - { .jtag_id = 0xb576, .die_rev = 0x0, .omap_id = 0x03320200, .type = 0x16100d00}, - { .jtag_id = 0xb613, .die_rev = 0x0, .omap_id = 0x03320300, .type = 0x1610ef00}, - { .jtag_id = 0xb613, .die_rev = 0x0, .omap_id = 0x03320300, .type = 0x1610ef00}, - { .jtag_id = 0xb576, .die_rev = 0x1, .omap_id = 0x03320100, .type = 0x16110000}, - { .jtag_id = 0xb58c, .die_rev = 0x2, .omap_id = 0x03320200, .type = 0x16110b00}, - { .jtag_id = 0xb58c, .die_rev = 0x3, .omap_id = 0x03320200, .type = 0x16110c00}, - { .jtag_id = 0xb65f, .die_rev = 0x0, .omap_id = 0x03320400, .type = 0x16212300}, - { .jtag_id = 0xb65f, .die_rev = 0x1, .omap_id = 0x03320400, .type = 0x16212300}, - { .jtag_id = 0xb65f, .die_rev = 0x1, .omap_id = 0x03320500, .type = 0x16212300}, - { .jtag_id = 0xb5f7, .die_rev = 0x0, .omap_id = 0x03330000, .type = 0x17100000}, - { .jtag_id = 0xb5f7, .die_rev = 0x1, .omap_id = 0x03330100, .type = 0x17100000}, - { .jtag_id = 0xb5f7, .die_rev = 0x2, .omap_id = 0x03330100, .type = 0x17100000}, -}; - -/* - * Get OMAP type from PROD_ID. - * 1710 has the PROD_ID in bits 15:00, not in 16:01 as documented in TRM. - * 1510 PROD_ID is empty, and 1610 PROD_ID does not make sense. - * Undocumented register in TEST BLOCK is used as fallback; This seems to - * work on 1510, 1610 & 1710. The official way hopefully will work in future - * processors. - */ -static u16 omap_get_jtag_id(void) -{ - u32 prod_id, omap_id; - - prod_id = omap_readl(OMAP_PRODUCTION_ID_1); - omap_id = omap_readl(OMAP32_ID_1); - - /* Check for unusable OMAP_PRODUCTION_ID_1 on 1611B/5912 and 730 */ - if (((prod_id >> 20) == 0) || (prod_id == omap_id)) - prod_id = 0; - else - prod_id &= 0xffff; - - if (prod_id) - return prod_id; - - /* Use OMAP32_ID_1 as fallback */ - prod_id = ((omap_id >> 12) & 0xffff); - - return prod_id; -} - -/* - * Get OMAP revision from DIE_REV. - * Early 1710 processors may have broken OMAP_DIE_ID, it contains PROD_ID. - * Undocumented register in the TEST BLOCK is used as fallback. - * REVISIT: This does not seem to work on 1510 - */ -static u8 omap_get_die_rev(void) -{ - u32 die_rev; - - die_rev = omap_readl(OMAP_DIE_ID_1); - - /* Check for broken OMAP_DIE_ID on early 1710 */ - if (((die_rev >> 12) & 0xffff) == omap_get_jtag_id()) - die_rev = 0; - - die_rev = (die_rev >> 17) & 0xf; - if (die_rev) - return die_rev; - - die_rev = (omap_readl(OMAP32_ID_1) >> 28) & 0xf; - - return die_rev; -} - -static unsigned long dpll1(void) -{ - unsigned short pll_ctl_val = omap_readw(DPLL_CTL_REG); - unsigned long rate; - - rate = CONFIG_SYS_CLK_FREQ; /* Base xtal rate */ - if (pll_ctl_val & 0x10) { - /* PLL enabled, apply multiplier and divisor */ - if (pll_ctl_val & 0xf80) - rate *= (pll_ctl_val & 0xf80) >> 7; - rate /= ((pll_ctl_val & 0x60) >> 5) + 1; - } else { - /* PLL disabled, apply bypass divisor */ - switch (pll_ctl_val & 0xc) { - case 0: - break; - case 0x4: - rate /= 2; - break; - default: - rate /= 4; - break; - } - } - - return rate; -} - -static unsigned long armcore(void) -{ - unsigned short arm_ckctl = omap_readw(ARM_CKCTL); - - return (dpll1() >> ((arm_ckctl & 0x0030) >> 4)); -} - -int print_cpuinfo (void) -{ - int i; - u16 jtag_id; - u8 die_rev; - u32 omap_id; - u8 cpu_type; - __maybe_unused u32 system_serial_high; - __maybe_unused u32 system_serial_low; - u32 system_rev = 0; - - jtag_id = omap_get_jtag_id(); - die_rev = omap_get_die_rev(); - omap_id = omap_readl(OMAP32_ID_0); - -#ifdef DEBUG - printf("OMAP_DIE_ID_0: 0x%08x\n", omap_readl(OMAP_DIE_ID_0)); - printf("OMAP_DIE_ID_1: 0x%08x DIE_REV: %i\n", - omap_readl(OMAP_DIE_ID_1), - (omap_readl(OMAP_DIE_ID_1) >> 17) & 0xf); - printf("OMAP_PRODUCTION_ID_0: 0x%08x\n", omap_readl(OMAP_PRODUCTION_ID_0)); - printf("OMAP_PRODUCTION_ID_1: 0x%08x JTAG_ID: 0x%04x\n", - omap_readl(OMAP_PRODUCTION_ID_1), - omap_readl(OMAP_PRODUCTION_ID_1) & 0xffff); - printf("OMAP32_ID_0: 0x%08x\n", omap_readl(OMAP32_ID_0)); - printf("OMAP32_ID_1: 0x%08x\n", omap_readl(OMAP32_ID_1)); - printf("JTAG_ID: 0x%04x DIE_REV: %i\n", jtag_id, die_rev); -#endif - - system_serial_high = omap_readl(OMAP_DIE_ID_0); - system_serial_low = omap_readl(OMAP_DIE_ID_1); - - /* First check only the major version in a safe way */ - for (i = 0; i < ARRAY_SIZE(omap_ids); i++) { - if (jtag_id == (omap_ids[i].jtag_id)) { - system_rev = omap_ids[i].type; - break; - } - } - - /* Check if we can find the die revision */ - for (i = 0; i < ARRAY_SIZE(omap_ids); i++) { - if (jtag_id == omap_ids[i].jtag_id && die_rev == omap_ids[i].die_rev) { - system_rev = omap_ids[i].type; - break; - } - } - - /* Finally check also the omap_id */ - for (i = 0; i < ARRAY_SIZE(omap_ids); i++) { - if (jtag_id == omap_ids[i].jtag_id - && die_rev == omap_ids[i].die_rev - && omap_id == omap_ids[i].omap_id) { - system_rev = omap_ids[i].type; - break; - } - } - - /* Add the cpu class info (7xx, 15xx, 16xx, 24xx) */ - cpu_type = system_rev >> 24; - - switch (cpu_type) { - case 0x07: - system_rev |= 0x07; - break; - case 0x03: - case 0x15: - system_rev |= 0x15; - break; - case 0x16: - case 0x17: - system_rev |= 0x16; - break; - case 0x24: - system_rev |= 0x24; - break; - default: - printf("Unknown OMAP cpu type: 0x%02x\n", cpu_type); - } - - printf("CPU: OMAP%04x", system_rev >> 16); - if ((system_rev >> 8) & 0xff) - printf("%x", (system_rev >> 8) & 0xff); -#ifdef DEBUG - printf(" revision %i handled as %02xxx id: %08x%08x", - die_rev, system_rev & 0xff, system_serial_low, system_serial_high); -#endif - printf(" at %ld.%01ld MHz (DPLL1=%ld.%01ld MHz)\n", - armcore() / 1000000, (armcore() / 100000) % 10, - dpll1() / 1000000, (dpll1() / 100000) % 10); - - return 0; -} - -#endif /* #if defined(CONFIG_OMAP) */ diff --git a/arch/arm/cpu/arm926ejs/omap/reset.S b/arch/arm/cpu/arm926ejs/omap/reset.S deleted file mode 100644 index 1c557b0d91..0000000000 --- a/arch/arm/cpu/arm926ejs/omap/reset.S +++ /dev/null @@ -1,29 +0,0 @@ -/* - * armboot - Startup Code for ARM926EJS CPU-core - * - * Copyright (c) 2003 Texas Instruments - * - * ----- Adapted for OMAP1610 OMAP730 from ARM925t code ------ - * - * Copyright (c) 2001 Marius Gröger <mag@sysgo.de> - * Copyright (c) 2002 Alex Züpke <azu@sysgo.de> - * Copyright (c) 2002 Gary Jennejohn <garyj@denx.de> - * Copyright (c) 2003 Richard Woodruff <r-woodruff2@ti.com> - * Copyright (c) 2003 Kshitij <kshitij@ti.com> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - - .align 5 -.globl reset_cpu -reset_cpu: - ldr r1, rstctl1 /* get clkm1 reset ctl */ - mov r3, #0x0 - strh r3, [r1] /* clear it */ - mov r3, #0x8 - strh r3, [r1] /* force dsp+arm reset */ -_loop_forever: - b _loop_forever - -rstctl1: - .word 0xfffece10 diff --git a/arch/arm/cpu/arm926ejs/omap/timer.c b/arch/arm/cpu/arm926ejs/omap/timer.c deleted file mode 100644 index b9715656c8..0000000000 --- a/arch/arm/cpu/arm926ejs/omap/timer.c +++ /dev/null @@ -1,152 +0,0 @@ -/* - * (C) Copyright 2003 - * Texas Instruments <www.ti.com> - * - * (C) Copyright 2002 - * Sysgo Real-Time Solutions, GmbH <www.elinos.com> - * Marius Groeger <mgroeger@sysgo.de> - * - * (C) Copyright 2002 - * Sysgo Real-Time Solutions, GmbH <www.elinos.com> - * Alex Zuepke <azu@sysgo.de> - * - * (C) Copyright 2002-2004 - * Gary Jennejohn, DENX Software Engineering, <garyj@denx.de> - * - * (C) Copyright 2004 - * Philippe Robin, ARM Ltd. <philippe.robin@arm.com> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <asm/io.h> - -#define TIMER_CLOCK (CONFIG_SYS_CLK_FREQ / (2 << CONFIG_SYS_PTV)) -#define TIMER_LOAD_VAL 0xffffffff - -/* macro to read the 32 bit timer */ -#define READ_TIMER readl(CONFIG_SYS_TIMERBASE+8) \ - / (TIMER_CLOCK / CONFIG_SYS_HZ) - -DECLARE_GLOBAL_DATA_PTR; - -#define timestamp gd->arch.tbl -#define lastdec gd->arch.lastinc - -int timer_init (void) -{ - int32_t val; - - /* Start the decrementer ticking down from 0xffffffff */ - *((int32_t *) (CONFIG_SYS_TIMERBASE + LOAD_TIM)) = TIMER_LOAD_VAL; - val = MPUTIM_ST | MPUTIM_AR | MPUTIM_CLOCK_ENABLE | (CONFIG_SYS_PTV << MPUTIM_PTV_BIT); - *((int32_t *) (CONFIG_SYS_TIMERBASE + CNTL_TIMER)) = val; - - /* init the timestamp and lastdec value */ - reset_timer_masked(); - - return 0; -} - -/* - * timer without interrupts - */ -ulong get_timer (ulong base) -{ - return get_timer_masked () - base; -} - -/* delay x useconds AND preserve advance timestamp value */ -void __udelay (unsigned long usec) -{ - ulong tmo, tmp; - - if(usec >= 1000){ /* if "big" number, spread normalization to seconds */ - tmo = usec / 1000; /* start to normalize for usec to ticks per sec */ - tmo *= CONFIG_SYS_HZ; /* find number of "ticks" to wait to achieve target */ - tmo /= 1000; /* finish normalize. */ - }else{ /* else small number, don't kill it prior to HZ multiply */ - tmo = usec * CONFIG_SYS_HZ; - tmo /= (1000*1000); - } - - tmp = get_timer (0); /* get current timestamp */ - if( (tmo + tmp + 1) < tmp ) /* if setting this fordward will roll time stamp */ - reset_timer_masked (); /* reset "advancing" timestamp to 0, set lastdec value */ - else - tmo += tmp; /* else, set advancing stamp wake up time */ - - while (get_timer_masked () < tmo)/* loop till event */ - /*NOP*/; -} - -void reset_timer_masked (void) -{ - /* reset time */ - lastdec = READ_TIMER; /* capure current decrementer value time */ - timestamp = 0; /* start "advancing" time stamp from 0 */ -} - -ulong get_timer_masked (void) -{ - ulong now = READ_TIMER; /* current tick value */ - - if (lastdec >= now) { /* normal mode (non roll) */ - /* normal mode */ - timestamp += lastdec - now; /* move stamp fordward with absoulte diff ticks */ - } else { /* we have overflow of the count down timer */ - /* nts = ts + ld + (TLV - now) - * ts=old stamp, ld=time that passed before passing through -1 - * (TLV-now) amount of time after passing though -1 - * nts = new "advancing time stamp"...it could also roll and cause problems. - */ - timestamp += lastdec + (TIMER_LOAD_VAL / (TIMER_CLOCK / - CONFIG_SYS_HZ)) - now; - } - lastdec = now; - - return timestamp; -} - -/* waits specified delay value and resets timestamp */ -void udelay_masked (unsigned long usec) -{ - ulong tmo; - ulong endtime; - signed long diff; - - if (usec >= 1000) { /* if "big" number, spread normalization to seconds */ - tmo = usec / 1000; /* start to normalize for usec to ticks per sec */ - tmo *= CONFIG_SYS_HZ; /* find number of "ticks" to wait to achieve target */ - tmo /= 1000; /* finish normalize. */ - } else { /* else small number, don't kill it prior to HZ multiply */ - tmo = usec * CONFIG_SYS_HZ; - tmo /= (1000*1000); - } - - endtime = get_timer_masked () + tmo; - - do { - ulong now = get_timer_masked (); - diff = endtime - now; - } while (diff >= 0); -} - -/* - * This function is derived from PowerPC code (read timebase as long long). - * On ARM it just returns the timer value. - */ -unsigned long long get_ticks(void) -{ - return get_timer(0); -} - -/* - * This function is derived from PowerPC code (timebase clock frequency). - * On ARM it returns the number of timer ticks per second. - */ -ulong get_tbclk (void) -{ - return CONFIG_SYS_HZ; -} diff --git a/arch/arm/cpu/armv8/start.S b/arch/arm/cpu/armv8/start.S index 62d97f7e88..354468b905 100644 --- a/arch/arm/cpu/armv8/start.S +++ b/arch/arm/cpu/armv8/start.S @@ -86,12 +86,12 @@ save_boot_params_ret: 0: /* - * Enalbe SMPEN bit for coherency. + * Enable SMPEN bit for coherency. * This register is not architectural but at the moment * this bit should be set for A53/A57/A72. */ #ifdef CONFIG_ARMV8_SET_SMPEN - mrs x0, S3_1_c15_c2_1 /* cpuactlr_el1 */ + mrs x0, S3_1_c15_c2_1 /* cpuectlr_el1 */ orr x0, x0, #0x40 msr S3_1_c15_c2_1, x0 #endif diff --git a/arch/arm/include/asm/arch-armada100/config.h b/arch/arm/include/asm/arch-armada100/config.h index 6ebc759f4b..113e1c73f3 100644 --- a/arch/arm/include/asm/arch-armada100/config.h +++ b/arch/arm/include/asm/arch-armada100/config.h @@ -24,17 +24,5 @@ #define MV_UART_CONSOLE_BASE ARMD1_UART1_BASE #define CONFIG_SYS_NS16550_IER (1 << 6) /* Bit 6 in UART_IER register represents UART Unit Enable */ -/* - * I2C definition - */ -#ifdef CONFIG_CMD_I2C -#define CONFIG_I2C_MV 1 -#define CONFIG_MV_I2C_NUM 2 -#define CONFIG_I2C_MULTI_BUS 1 -#define CONFIG_MV_I2C_REG {0xd4011000, 0xd4025000} -#define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 0 -#define CONFIG_SYS_I2C_SLAVE 0xfe -#endif #endif /* _ARMD1_CONFIG_H */ diff --git a/arch/arm/include/asm/arch-mx7ulp/clock.h b/arch/arm/include/asm/arch-mx7ulp/clock.h index 170a9b3a7c..6424fafe14 100644 --- a/arch/arm/include/asm/arch-mx7ulp/clock.h +++ b/arch/arm/include/asm/arch-mx7ulp/clock.h @@ -34,7 +34,7 @@ u32 imx_get_i2cclk(unsigned i2c_num); #ifdef CONFIG_MXC_OCOTP void enable_ocotp_clk(unsigned char enable); #endif -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD void enable_usboh3_clk(unsigned char enable); #endif void init_clk_usdhc(u32 index); diff --git a/arch/arm/include/asm/arch-omap5/clock.h b/arch/arm/include/asm/arch-omap5/clock.h index 7ea7199f2b..0c99bbdc93 100644 --- a/arch/arm/include/asm/arch-omap5/clock.h +++ b/arch/arm/include/asm/arch-omap5/clock.h @@ -370,13 +370,6 @@ #define DPLL_NO_LOCK 0 #define DPLL_LOCK 1 -/* - * MAX value for PRM_RSTTIME[9:0]RSTTIME1 stored is 0x3ff. - * 0x3ff is in the no of FUNC_32K_CLK cycles. Converting cycles - * into microsec and passing the value. - */ -#define CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC 31219 - #if defined(CONFIG_DRA7XX) #define V_OSCK 20000000 /* Clock output from T2 */ #else diff --git a/arch/arm/include/asm/arch-sunxi/clock_sun6i.h b/arch/arm/include/asm/arch-sunxi/clock_sun6i.h index faa14791f9..d328df9597 100644 --- a/arch/arm/include/asm/arch-sunxi/clock_sun6i.h +++ b/arch/arm/include/asm/arch-sunxi/clock_sun6i.h @@ -84,7 +84,8 @@ struct sunxi_ccm_reg { u32 lcd0_ch0_clk_cfg; /* 0x118 LCD0 CH0 module clock */ u32 lcd1_ch0_clk_cfg; /* 0x11c LCD1 CH0 module clock */ #endif - u32 reserved14[3]; + u32 tve_clk_cfg; /* 0x120 H3/H5 TVE module clock */ + u32 reserved14[2]; u32 lcd0_ch1_clk_cfg; /* 0x12c LCD0 CH1 module clock */ u32 lcd1_ch1_clk_cfg; /* 0x130 LCD1 CH1 module clock */ u32 csi0_clk_cfg; /* 0x134 CSI0 module clock */ @@ -307,6 +308,7 @@ struct sunxi_ccm_reg { #define AHB_GATE_OFFSET_DE_BE0 12 #define AHB_GATE_OFFSET_DE 12 #define AHB_GATE_OFFSET_HDMI 11 +#define AHB_GATE_OFFSET_TVE 9 #ifndef CONFIG_SUNXI_DE2 #define AHB_GATE_OFFSET_LCD1 5 #define AHB_GATE_OFFSET_LCD0 4 @@ -415,6 +417,9 @@ struct sunxi_ccm_reg { #define CCM_HDMI_SLOW_CTRL_DDC_GATE (1 << 31) +#define CCM_TVE_CTRL_GATE (0x1 << 31) +#define CCM_TVE_CTRL_M(n) ((((n) - 1) & 0xf) << 0) + #if defined(CONFIG_MACH_SUN50I) #define MBUS_CLK_DEFAULT 0x81000002 /* PLL6x2 / 3 */ #elif defined(CONFIG_MACH_SUN8I) @@ -448,6 +453,7 @@ struct sunxi_ccm_reg { #define AHB_RESET_OFFSET_DE 12 #define AHB_RESET_OFFSET_HDMI 11 #define AHB_RESET_OFFSET_HDMI2 10 +#define AHB_RESET_OFFSET_TVE 9 #ifndef CONFIG_SUNXI_DE2 #define AHB_RESET_OFFSET_LCD1 5 #define AHB_RESET_OFFSET_LCD0 4 diff --git a/arch/arm/include/asm/arch-sunxi/display.h b/arch/arm/include/asm/arch-sunxi/display.h index 93803addfb..e10197784e 100644 --- a/arch/arm/include/asm/arch-sunxi/display.h +++ b/arch/arm/include/asm/arch-sunxi/display.h @@ -225,52 +225,6 @@ struct sunxi_hdmi_reg { }; /* - * This is based on the A10s User Manual, and the A10s only supports - * composite video and not vga like the A10 / A20 does, still other - * than the removed vga out capability the tvencoder seems to be the same. - * "unknown#" registers are registers which are used in the A10 kernel code, - * but not documented in the A10s User Manual. - */ -struct sunxi_tve_reg { - u32 gctrl; /* 0x000 */ - u32 cfg0; /* 0x004 */ - u32 dac_cfg0; /* 0x008 */ - u32 filter; /* 0x00c */ - u32 chroma_freq; /* 0x010 */ - u32 porch_num; /* 0x014 */ - u32 unknown0; /* 0x018 */ - u32 line_num; /* 0x01c */ - u32 blank_black_level; /* 0x020 */ - u32 unknown1; /* 0x024, seems to be 1 byte per dac */ - u8 res0[0x08]; /* 0x028 */ - u32 auto_detect_en; /* 0x030 */ - u32 auto_detect_int_status; /* 0x034 */ - u32 auto_detect_status; /* 0x038 */ - u32 auto_detect_debounce; /* 0x03c */ - u32 csc_reg0; /* 0x040 */ - u32 csc_reg1; /* 0x044 */ - u32 csc_reg2; /* 0x048 */ - u32 csc_reg3; /* 0x04c */ - u8 res1[0xb0]; /* 0x050 */ - u32 color_burst; /* 0x100 */ - u32 vsync_num; /* 0x104 */ - u32 notch_freq; /* 0x108 */ - u32 cbr_level; /* 0x10c */ - u32 burst_phase; /* 0x110 */ - u32 burst_width; /* 0x114 */ - u32 unknown2; /* 0x118 */ - u32 sync_vbi_level; /* 0x11c */ - u32 white_level; /* 0x120 */ - u32 active_num; /* 0x124 */ - u32 chroma_bw_gain; /* 0x128 */ - u32 notch_width; /* 0x12c */ - u32 resync_num; /* 0x130 */ - u32 slave_para; /* 0x134 */ - u32 cfg1; /* 0x138 */ - u32 cfg2; /* 0x13c */ -}; - -/* * DE-FE register constants. */ #define SUNXI_DE_FE_WIDTH(x) (((x) - 1) << 0) @@ -394,67 +348,6 @@ struct sunxi_tve_reg { #define SUNXI_HMDI_DDC_LINE_CTRL_SCL_ENABLE (1 << 8) #define SUNXI_HMDI_DDC_LINE_CTRL_SDA_ENABLE (1 << 9) -/* - * TVE register constants. - */ -#define SUNXI_TVE_GCTRL_ENABLE (1 << 0) -/* - * Select input 0 to disable dac, 1 - 4 to feed dac from tve0, 5 - 8 to feed - * dac from tve1. When using tve1 the mux value must be written to both tve0's - * and tve1's gctrl reg. - */ -#define SUNXI_TVE_GCTRL_DAC_INPUT_MASK(dac) (0xf << (((dac) + 1) * 4)) -#define SUNXI_TVE_GCTRL_DAC_INPUT(dac, sel) ((sel) << (((dac) + 1) * 4)) -#define SUNXI_TVE_CFG0_VGA 0x20000000 -#define SUNXI_TVE_CFG0_PAL 0x07030001 -#define SUNXI_TVE_CFG0_NTSC 0x07030000 -#define SUNXI_TVE_DAC_CFG0_VGA 0x403e1ac7 -#ifdef CONFIG_MACH_SUN5I -#define SUNXI_TVE_DAC_CFG0_COMPOSITE 0x433f0009 -#else -#define SUNXI_TVE_DAC_CFG0_COMPOSITE 0x403f0008 -#endif -#define SUNXI_TVE_FILTER_COMPOSITE 0x00000120 -#define SUNXI_TVE_CHROMA_FREQ_PAL_M 0x21e6efe3 -#define SUNXI_TVE_CHROMA_FREQ_PAL_NC 0x21f69446 -#define SUNXI_TVE_PORCH_NUM_PAL 0x008a0018 -#define SUNXI_TVE_PORCH_NUM_NTSC 0x00760020 -#define SUNXI_TVE_LINE_NUM_PAL 0x00160271 -#define SUNXI_TVE_LINE_NUM_NTSC 0x0016020d -#define SUNXI_TVE_BLANK_BLACK_LEVEL_PAL 0x00fc00fc -#define SUNXI_TVE_BLANK_BLACK_LEVEL_NTSC 0x00f0011a -#define SUNXI_TVE_UNKNOWN1_VGA 0x00000000 -#define SUNXI_TVE_UNKNOWN1_COMPOSITE 0x18181818 -#define SUNXI_TVE_AUTO_DETECT_EN_DET_EN(dac) (1 << ((dac) + 0)) -#define SUNXI_TVE_AUTO_DETECT_EN_INT_EN(dac) (1 << ((dac) + 16)) -#define SUNXI_TVE_AUTO_DETECT_INT_STATUS(dac) (1 << ((dac) + 0)) -#define SUNXI_TVE_AUTO_DETECT_STATUS_SHIFT(dac) ((dac) * 8) -#define SUNXI_TVE_AUTO_DETECT_STATUS_MASK(dac) (3 << ((dac) * 8)) -#define SUNXI_TVE_AUTO_DETECT_STATUS_NONE 0 -#define SUNXI_TVE_AUTO_DETECT_STATUS_CONNECTED 1 -#define SUNXI_TVE_AUTO_DETECT_STATUS_SHORT_GND 3 -#define SUNXI_TVE_AUTO_DETECT_DEBOUNCE_SHIFT(d) ((d) * 8) -#define SUNXI_TVE_AUTO_DETECT_DEBOUNCE_MASK(d) (0xf << ((d) * 8)) -#define SUNXI_TVE_CSC_REG0_ENABLE (1 << 31) -#define SUNXI_TVE_CSC_REG0 0x08440832 -#define SUNXI_TVE_CSC_REG1 0x3b6dace1 -#define SUNXI_TVE_CSC_REG2 0x0e1d13dc -#define SUNXI_TVE_CSC_REG3 0x00108080 -#define SUNXI_TVE_COLOR_BURST_PAL_M 0x00000000 -#define SUNXI_TVE_CBR_LEVEL_PAL 0x00002828 -#define SUNXI_TVE_CBR_LEVEL_NTSC 0x0000004f -#define SUNXI_TVE_BURST_PHASE_NTSC 0x00000000 -#define SUNXI_TVE_BURST_WIDTH_COMPOSITE 0x0016447e -#define SUNXI_TVE_UNKNOWN2_PAL 0x0000e0e0 -#define SUNXI_TVE_UNKNOWN2_NTSC 0x0000a0a0 -#define SUNXI_TVE_SYNC_VBI_LEVEL_NTSC 0x001000f0 -#define SUNXI_TVE_ACTIVE_NUM_COMPOSITE 0x000005a0 -#define SUNXI_TVE_CHROMA_BW_GAIN_COMP 0x00000002 -#define SUNXI_TVE_NOTCH_WIDTH_COMPOSITE 0x00000101 -#define SUNXI_TVE_RESYNC_NUM_PAL 0x800d000c -#define SUNXI_TVE_RESYNC_NUM_NTSC 0x000e000c -#define SUNXI_TVE_SLAVE_PARA_COMPOSITE 0x00000000 - int sunxi_simplefb_setup(void *blob); #endif /* _SUNXI_DISPLAY_H */ diff --git a/arch/arm/include/asm/arch-sunxi/tve.h b/arch/arm/include/asm/arch-sunxi/tve.h new file mode 100644 index 0000000000..41a14a68e4 --- /dev/null +++ b/arch/arm/include/asm/arch-sunxi/tve.h @@ -0,0 +1,131 @@ +/* + * Sunxi TV encoder register and constant defines + * + * (C) Copyright 2014 Hans de Goede <hdegoede@redhat.com> + * (C) Copyright 2017 Jernej Skrabec <jernej.skrabec@siol.net> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef _TVE_H +#define _TVE_H + +enum tve_mode { + tve_mode_vga, + tve_mode_composite_pal, + tve_mode_composite_ntsc, + tve_mode_composite_pal_m, + tve_mode_composite_pal_nc, +}; + +/* + * This is based on the A10s User Manual, and the A10s only supports + * composite video and not vga like the A10 / A20 does, still other + * than the removed vga out capability the tvencoder seems to be the same. + * "unknown#" registers are registers which are used in the A10 kernel code, + * but not documented in the A10s User Manual. + */ +struct sunxi_tve_reg { + u32 gctrl; /* 0x000 */ + u32 cfg0; /* 0x004 */ + u32 dac_cfg0; /* 0x008 */ + u32 filter; /* 0x00c */ + u32 chroma_freq; /* 0x010 */ + u32 porch_num; /* 0x014 */ + u32 unknown0; /* 0x018 */ + u32 line_num; /* 0x01c */ + u32 blank_black_level; /* 0x020 */ + u32 unknown1; /* 0x024, seems to be 1 byte per dac */ + u8 res0[0x08]; /* 0x028 */ + u32 auto_detect_en; /* 0x030 */ + u32 auto_detect_int_status; /* 0x034 */ + u32 auto_detect_status; /* 0x038 */ + u32 auto_detect_debounce; /* 0x03c */ + u32 csc_reg0; /* 0x040 */ + u32 csc_reg1; /* 0x044 */ + u32 csc_reg2; /* 0x048 */ + u32 csc_reg3; /* 0x04c */ + u8 res1[0xb0]; /* 0x050 */ + u32 color_burst; /* 0x100 */ + u32 vsync_num; /* 0x104 */ + u32 notch_freq; /* 0x108 */ + u32 cbr_level; /* 0x10c */ + u32 burst_phase; /* 0x110 */ + u32 burst_width; /* 0x114 */ + u32 unknown2; /* 0x118 */ + u32 sync_vbi_level; /* 0x11c */ + u32 white_level; /* 0x120 */ + u32 active_num; /* 0x124 */ + u32 chroma_bw_gain; /* 0x128 */ + u32 notch_width; /* 0x12c */ + u32 resync_num; /* 0x130 */ + u32 slave_para; /* 0x134 */ + u32 cfg1; /* 0x138 */ + u32 cfg2; /* 0x13c */ +}; + +/* + * TVE register constants. + */ +#define SUNXI_TVE_GCTRL_ENABLE (1 << 0) +/* + * Select input 0 to disable dac, 1 - 4 to feed dac from tve0, 5 - 8 to feed + * dac from tve1. When using tve1 the mux value must be written to both tve0's + * and tve1's gctrl reg. + */ +#define SUNXI_TVE_GCTRL_DAC_INPUT_MASK(dac) (0xf << (((dac) + 1) * 4)) +#define SUNXI_TVE_GCTRL_DAC_INPUT(dac, sel) ((sel) << (((dac) + 1) * 4)) +#define SUNXI_TVE_CFG0_VGA 0x20000000 +#define SUNXI_TVE_CFG0_PAL 0x07030001 +#define SUNXI_TVE_CFG0_NTSC 0x07030000 +#define SUNXI_TVE_DAC_CFG0_VGA 0x403e1ac7 +#ifdef CONFIG_MACH_SUN5I +#define SUNXI_TVE_DAC_CFG0_COMPOSITE 0x433f0009 +#else +#define SUNXI_TVE_DAC_CFG0_COMPOSITE 0x403f0008 +#endif +#define SUNXI_TVE_FILTER_COMPOSITE 0x00000120 +#define SUNXI_TVE_CHROMA_FREQ_PAL_M 0x21e6efe3 +#define SUNXI_TVE_CHROMA_FREQ_PAL_NC 0x21f69446 +#define SUNXI_TVE_PORCH_NUM_PAL 0x008a0018 +#define SUNXI_TVE_PORCH_NUM_NTSC 0x00760020 +#define SUNXI_TVE_LINE_NUM_PAL 0x00160271 +#define SUNXI_TVE_LINE_NUM_NTSC 0x0016020d +#define SUNXI_TVE_BLANK_BLACK_LEVEL_PAL 0x00fc00fc +#define SUNXI_TVE_BLANK_BLACK_LEVEL_NTSC 0x00f0011a +#define SUNXI_TVE_UNKNOWN1_VGA 0x00000000 +#define SUNXI_TVE_UNKNOWN1_COMPOSITE 0x18181818 +#define SUNXI_TVE_AUTO_DETECT_EN_DET_EN(dac) (1 << ((dac) + 0)) +#define SUNXI_TVE_AUTO_DETECT_EN_INT_EN(dac) (1 << ((dac) + 16)) +#define SUNXI_TVE_AUTO_DETECT_INT_STATUS(dac) (1 << ((dac) + 0)) +#define SUNXI_TVE_AUTO_DETECT_STATUS_SHIFT(dac) ((dac) * 8) +#define SUNXI_TVE_AUTO_DETECT_STATUS_MASK(dac) (3 << ((dac) * 8)) +#define SUNXI_TVE_AUTO_DETECT_STATUS_NONE 0 +#define SUNXI_TVE_AUTO_DETECT_STATUS_CONNECTED 1 +#define SUNXI_TVE_AUTO_DETECT_STATUS_SHORT_GND 3 +#define SUNXI_TVE_AUTO_DETECT_DEBOUNCE_SHIFT(d) ((d) * 8) +#define SUNXI_TVE_AUTO_DETECT_DEBOUNCE_MASK(d) (0xf << ((d) * 8)) +#define SUNXI_TVE_CSC_REG0_ENABLE (1 << 31) +#define SUNXI_TVE_CSC_REG0 0x08440832 +#define SUNXI_TVE_CSC_REG1 0x3b6dace1 +#define SUNXI_TVE_CSC_REG2 0x0e1d13dc +#define SUNXI_TVE_CSC_REG3 0x00108080 +#define SUNXI_TVE_COLOR_BURST_PAL_M 0x00000000 +#define SUNXI_TVE_CBR_LEVEL_PAL 0x00002828 +#define SUNXI_TVE_CBR_LEVEL_NTSC 0x0000004f +#define SUNXI_TVE_BURST_PHASE_NTSC 0x00000000 +#define SUNXI_TVE_BURST_WIDTH_COMPOSITE 0x0016447e +#define SUNXI_TVE_UNKNOWN2_PAL 0x0000e0e0 +#define SUNXI_TVE_UNKNOWN2_NTSC 0x0000a0a0 +#define SUNXI_TVE_SYNC_VBI_LEVEL_NTSC 0x001000f0 +#define SUNXI_TVE_ACTIVE_NUM_COMPOSITE 0x000005a0 +#define SUNXI_TVE_CHROMA_BW_GAIN_COMP 0x00000002 +#define SUNXI_TVE_NOTCH_WIDTH_COMPOSITE 0x00000101 +#define SUNXI_TVE_RESYNC_NUM_PAL 0x800d000c +#define SUNXI_TVE_RESYNC_NUM_NTSC 0x000e000c +#define SUNXI_TVE_SLAVE_PARA_COMPOSITE 0x00000000 + +void tvencoder_mode_set(struct sunxi_tve_reg * const tve, enum tve_mode mode); +void tvencoder_enable(struct sunxi_tve_reg * const tve); + +#endif /* _TVE_H */ diff --git a/arch/arm/include/asm/spl.h b/arch/arm/include/asm/spl.h index a0bda28104..5d7f7e6ec5 100644 --- a/arch/arm/include/asm/spl.h +++ b/arch/arm/include/asm/spl.h @@ -7,7 +7,7 @@ #ifndef _ASM_SPL_H_ #define _ASM_SPL_H_ -#if defined(CONFIG_OMAP) \ +#if defined(CONFIG_ARCH_OMAP2PLUS) \ || defined(CONFIG_EXYNOS4) || defined(CONFIG_EXYNOS5) \ || defined(CONFIG_EXYNOS4210) /* Platform-specific defines */ diff --git a/arch/arm/mach-at91/arm926ejs/at91sam9x5_devices.c b/arch/arm/mach-at91/arm926ejs/at91sam9x5_devices.c index 8de086efd6..a939b1fb8d 100644 --- a/arch/arm/mach-at91/arm926ejs/at91sam9x5_devices.c +++ b/arch/arm/mach-at91/arm926ejs/at91sam9x5_devices.c @@ -161,7 +161,7 @@ void at91_spi1_hw_init(unsigned long cs_mask) } #endif -#if defined(CONFIG_USB_OHCI_NEW) || defined(CONFIG_USB_EHCI) +#if defined(CONFIG_USB_OHCI_NEW) || defined(CONFIG_USB_EHCI_HCD) void at91_uhp_hw_init(void) { /* Enable VBus on UHP ports */ diff --git a/arch/arm/mach-kirkwood/include/mach/config.h b/arch/arm/mach-kirkwood/include/mach/config.h index b786df0aaf..c7beb58e80 100644 --- a/arch/arm/mach-kirkwood/include/mach/config.h +++ b/arch/arm/mach-kirkwood/include/mach/config.h @@ -89,7 +89,6 @@ * USB/EHCI */ #ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI_MARVELL #define CONFIG_EHCI_IS_TDI #endif /* CONFIG_CMD_USB */ diff --git a/arch/arm/mach-omap2/omap3/Kconfig b/arch/arm/mach-omap2/omap3/Kconfig index 933fcba37c..7b298d671d 100644 --- a/arch/arm/mach-omap2/omap3/Kconfig +++ b/arch/arm/mach-omap2/omap3/Kconfig @@ -1,5 +1,21 @@ if OMAP34XX +# We only enable the clocks for the GPIO banks that a given board requies. +config OMAP3_GPIO_2 + bool + +config OMAP3_GPIO_3 + bool + +config OMAP3_GPIO_4 + bool + +config OMAP3_GPIO_5 + bool + +config OMAP3_GPIO_6 + bool + choice prompt "OMAP3 board select" optional @@ -9,18 +25,28 @@ config TARGET_AM3517_EVM config TARGET_MT_VENTOUX bool "TeeJet Mt.Ventoux" + select OMAP3_GPIO_4 + select OMAP3_GPIO_5 if USB_EHCI_HCD config TARGET_OMAP3_BEAGLE bool "TI OMAP3 BeagleBoard" select DM select DM_SERIAL select DM_GPIO + select OMAP3_GPIO_5 + select OMAP3_GPIO_6 config TARGET_CM_T35 bool "CompuLab CM-T3530 and CM-T3730 boards" + select OMAP3_GPIO_2 + select OMAP3_GPIO_5 + select OMAP3_GPIO_6 if LED_STATUS config TARGET_CM_T3517 bool "CompuLab CM-T3517 boards" + select OMAP3_GPIO_2 + select OMAP3_GPIO_5 + select OMAP3_GPIO_6 if LED_STATUS config TARGET_DEVKIT8000 bool "TimLL OMAP3 Devkit8000" @@ -36,12 +62,20 @@ config TARGET_OMAP3_IGEP00X0 select DM select DM_SERIAL select DM_GPIO + select OMAP3_GPIO_3 + select OMAP3_GPIO_5 + select OMAP3_GPIO_6 config TARGET_OMAP3_OVERO bool "OMAP35xx Gumstix Overo" select DM select DM_SERIAL select DM_GPIO + select OMAP3_GPIO_2 + select OMAP3_GPIO_3 + select OMAP3_GPIO_4 + select OMAP3_GPIO_5 + select OMAP3_GPIO_6 config TARGET_OMAP3_ZOOM1 bool "TI Zoom1" @@ -54,16 +88,22 @@ config TARGET_AM3517_CRANE config TARGET_OMAP3_PANDORA bool "OMAP3 Pandora" + select OMAP3_GPIO_4 + select OMAP3_GPIO_6 config TARGET_ECO5PK bool "ECO5PK" + select OMAP3_GPIO_5 if USB_EHCI_HCD config TARGET_TRICORDER bool "Tricorder" + select OMAP3_GPIO_2 config TARGET_MCX bool "MCX" select BOARD_LATE_INIT + select OMAP3_GPIO_2 if USB_EHCI_HCD + select OMAP3_GPIO_5 if USB_EHCI_HCD config TARGET_OMAP3_LOGIC bool "OMAP3 Logic" @@ -71,15 +111,24 @@ config TARGET_OMAP3_LOGIC select DM select DM_SERIAL select DM_GPIO + select OMAP3_GPIO_4 + select OMAP3_GPIO_6 config TARGET_NOKIA_RX51 bool "Nokia RX51" config TARGET_TAO3530 bool "TAO3530" + select OMAP3_GPIO_2 + select OMAP3_GPIO_3 + select OMAP3_GPIO_4 + select OMAP3_GPIO_5 + select OMAP3_GPIO_6 config TARGET_TWISTER bool "Twister" + select OMAP3_GPIO_2 + select OMAP3_GPIO_5 if USB_EHCI_HCD config TARGET_OMAP3_CAIRO bool "QUIPOS CAIRO" @@ -92,6 +141,11 @@ config TARGET_SNIPER select DM select DM_SERIAL select DM_GPIO + select OMAP3_GPIO_2 + select OMAP3_GPIO_3 + select OMAP3_GPIO_4 + select OMAP3_GPIO_5 + select OMAP3_GPIO_6 endchoice diff --git a/arch/arm/mach-omap2/omap5/Kconfig b/arch/arm/mach-omap2/omap5/Kconfig index c89c438305..1a66abdeb2 100644 --- a/arch/arm/mach-omap2/omap5/Kconfig +++ b/arch/arm/mach-omap2/omap5/Kconfig @@ -63,6 +63,23 @@ config TI_SECURE_EMIF_PROTECTED_REGION_SIZE using hardware memory firewalls. This value must be smaller than the TI_SECURE_EMIF_TOTAL_REGION_SIZE value. +config OMAP_PLATFORM_RESET_TIME_MAX_USEC + int "Something" + range 0 31219 + default 31219 + help + Most OMAPs' provide a way to specify the time for which the reset + should be held low while the voltages and Oscillator outputs + stabilize. + This time is mostly board and PMIC dependent. Hence the boards are + expected to specify a pre-computed time using the above option. + This value can be computed using a summation of the below 3 + parameters + 1: Time taken by the Osciallator to stop and restart + 2: PMIC OTP time + 3: Voltage ramp time, which can be derived using the PMIC slew rate + and value of voltage ramp needed. + if TARGET_DRA7XX_EVM || TARGET_AM57XX_EVM menu "Voltage Domain OPP selections" diff --git a/arch/arm/mach-omap2/omap5/hwinit.c b/arch/arm/mach-omap2/omap5/hwinit.c index 839d79d102..afe59e0b58 100644 --- a/arch/arm/mach-omap2/omap5/hwinit.c +++ b/arch/arm/mach-omap2/omap5/hwinit.c @@ -414,12 +414,13 @@ void setup_warmreset_time(void) { u32 rst_time, rst_val; -#ifndef CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC - rst_time = CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC; -#else - rst_time = CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC; -#endif - rst_time = usec_to_32k(rst_time) << RSTTIME1_SHIFT; + /* + * MAX value for PRM_RSTTIME[9:0]RSTTIME1 stored is 0x3ff. + * 0x3ff is in the no of FUNC_32K_CLK cycles. Converting cycles + * into microsec and passing the value. + */ + rst_time = usec_to_32k(CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC) + << RSTTIME1_SHIFT; if (rst_time > RSTTIME1_MASK) rst_time = RSTTIME1_MASK; diff --git a/arch/arm/mach-omap2/vc.c b/arch/arm/mach-omap2/vc.c index a68f1d145d..b7f79800de 100644 --- a/arch/arm/mach-omap2/vc.c +++ b/arch/arm/mach-omap2/vc.c @@ -19,14 +19,6 @@ #include <asm/arch/sys_proto.h> #include <asm/arch/clock.h> -/* - * Define Master code if there are multiple masters on the I2C_SR bus. - * Normally not required - */ -#ifndef CONFIG_OMAP_VC_I2C_HS_MCODE -#define CONFIG_OMAP_VC_I2C_HS_MCODE 0x0 -#endif - /* Register defines and masks for VC IP Block */ /* PRM_VC_CFG_I2C_MODE */ #define PRM_VC_CFG_I2C_MODE_DFILTEREN_BIT (0x1 << 6) @@ -84,8 +76,10 @@ static void omap_vc_init(u16 speed_khz) (cycles_low << PRM_VC_CFG_I2C_CLK_SCLL_SHIFT); writel(val, (*prcm)->prm_vc_cfg_i2c_clk); - val = CONFIG_OMAP_VC_I2C_HS_MCODE << - PRM_VC_CFG_I2C_MODE_HSMCODE_SHIFT; + /* + * Master code if there are multiple masters on the I2C_SR bus. + */ + val = 0x0 << PRM_VC_CFG_I2C_MODE_HSMCODE_SHIFT; /* No HS mode for now */ val &= ~PRM_VC_CFG_I2C_MODE_HSMODEEN_BIT; writel(val, (*prcm)->prm_vc_cfg_i2c_mode); diff --git a/arch/arm/mach-uniphier/clk/clk-ld11.c b/arch/arm/mach-uniphier/clk/clk-ld11.c index 36aa787984..0266e7e66b 100644 --- a/arch/arm/mach-uniphier/clk/clk-ld11.c +++ b/arch/arm/mach-uniphier/clk/clk-ld11.c @@ -33,7 +33,7 @@ void uniphier_ld11_clk_init(void) /* TODO: use "mmc-pwrseq-emmc" */ writel(1, SDCTRL_EMMC_HW_RESET); -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD { /* FIXME: the current clk driver can not handle parents */ u32 tmp; diff --git a/arch/arm/mach-uniphier/clk/clk-ld4.c b/arch/arm/mach-uniphier/clk/clk-ld4.c index 62b6927732..def87c1aac 100644 --- a/arch/arm/mach-uniphier/clk/clk-ld4.c +++ b/arch/arm/mach-uniphier/clk/clk-ld4.c @@ -31,7 +31,7 @@ void uniphier_ld4_clk_init(void) #ifdef CONFIG_UNIPHIER_ETH tmp |= SC_CLKCTRL_CEN_ETHER; #endif -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD tmp |= SC_CLKCTRL_CEN_MIO | SC_CLKCTRL_CEN_STDMAC; #endif #ifdef CONFIG_NAND_DENALI diff --git a/arch/arm/mach-uniphier/clk/clk-pro4.c b/arch/arm/mach-uniphier/clk/clk-pro4.c index 92b73384ab..19be4f3145 100644 --- a/arch/arm/mach-uniphier/clk/clk-pro4.c +++ b/arch/arm/mach-uniphier/clk/clk-pro4.c @@ -46,7 +46,7 @@ void uniphier_pro4_clk_init(void) #ifdef CONFIG_UNIPHIER_ETH tmp |= SC_CLKCTRL_CEN_ETHER; #endif -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD tmp |= SC_CLKCTRL_CEN_MIO | SC_CLKCTRL_CEN_STDMAC; #endif #ifdef CONFIG_NAND_DENALI diff --git a/arch/powerpc/Kconfig b/arch/powerpc/Kconfig index 0033c35261..01e9008d0a 100644 --- a/arch/powerpc/Kconfig +++ b/arch/powerpc/Kconfig @@ -32,6 +32,7 @@ config MPC85xx select CREATE_ARCH_SYMLINK select SYS_FSL_DDR select SYS_FSL_DDR_BE + imply USB_EHCI_HCD if USB config MPC86xx bool "MPC86xx" diff --git a/arch/powerpc/cpu/mpc512x/Makefile b/arch/powerpc/cpu/mpc512x/Makefile index 98991c688b..933deebdae 100644 --- a/arch/powerpc/cpu/mpc512x/Makefile +++ b/arch/powerpc/cpu/mpc512x/Makefile @@ -9,7 +9,6 @@ obj-y := cpu.o obj-y += traps.o obj-y += cpu_init.o obj-y += fixed_sdram.o -obj-y += i2c.o obj-y += interrupts.o obj-y += iopin.o obj-y += serial.o diff --git a/arch/powerpc/cpu/mpc512x/i2c.c b/arch/powerpc/cpu/mpc512x/i2c.c deleted file mode 100644 index 15d519a116..0000000000 --- a/arch/powerpc/cpu/mpc512x/i2c.c +++ /dev/null @@ -1,386 +0,0 @@ -/* - * (C) Copyright 2003 - 2009 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - * - * Based on the MPC5xxx code. - */ - -#include <common.h> -#include <asm/io.h> - -DECLARE_GLOBAL_DATA_PTR; - -#ifdef CONFIG_HARD_I2C - -#include <i2c.h> - -/* by default set I2C bus 0 active */ -static unsigned int bus_num __attribute__ ((section (".data"))) = 0; - -#define I2C_TIMEOUT 100 -#define I2C_RETRIES 3 - -struct mpc512x_i2c_tap { - int scl2tap; - int tap2tap; -}; - -static int mpc_reg_in(volatile u32 *reg); -static void mpc_reg_out(volatile u32 *reg, int val, int mask); -static int wait_for_bb(void); -static int wait_for_pin(int *status); -static int do_address(uchar chip, char rdwr_flag); -static int send_bytes(uchar chip, char *buf, int len); -static int receive_bytes(uchar chip, char *buf, int len); -static int mpc_get_fdr(int); - -static int mpc_reg_in (volatile u32 *reg) -{ - int ret = in_be32(reg) >> 24; - - return ret; -} - -static void mpc_reg_out (volatile u32 *reg, int val, int mask) -{ - if (!mask) { - out_be32(reg, val << 24); - } else { - clrsetbits_be32(reg, mask << 24, (val & mask) << 24); - } -} - -static int wait_for_bb (void) -{ - volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR; - volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num]; - int timeout = I2C_TIMEOUT; - int status; - - status = mpc_reg_in (®s->msr); - - while (timeout-- && (status & I2C_BB)) { - mpc_reg_out (®s->mcr, I2C_STA, I2C_STA); - (void)mpc_reg_in(®s->mdr); - mpc_reg_out (®s->mcr, 0, I2C_STA); - mpc_reg_out (®s->mcr, 0, 0); - mpc_reg_out (®s->mcr, I2C_EN, 0); - - udelay (1000); - status = mpc_reg_in (®s->msr); - } - - return (status & I2C_BB); -} - -static int wait_for_pin (int *status) -{ - volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR; - volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num]; - int timeout = I2C_TIMEOUT; - - *status = mpc_reg_in (®s->msr); - - while (timeout-- && !(*status & I2C_IF)) { - udelay (1000); - *status = mpc_reg_in (®s->msr); - } - - if (!(*status & I2C_IF)) { - return -1; - } - - mpc_reg_out (®s->msr, 0, I2C_IF); - - return 0; -} - -static int do_address (uchar chip, char rdwr_flag) -{ - volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR; - volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num]; - int status; - - chip <<= 1; - - if (rdwr_flag) { - chip |= 1; - } - - mpc_reg_out (®s->mcr, I2C_TX, I2C_TX); - mpc_reg_out (®s->mdr, chip, 0); - - if (wait_for_pin (&status)) { - return -2; - } - - if (status & I2C_RXAK) { - return -3; - } - - return 0; -} - -static int send_bytes (uchar chip, char *buf, int len) -{ - volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR; - volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num]; - int wrcount; - int status; - - for (wrcount = 0; wrcount < len; ++wrcount) { - - mpc_reg_out (®s->mdr, buf[wrcount], 0); - - if (wait_for_pin (&status)) { - break; - } - - if (status & I2C_RXAK) { - break; - } - - } - - return !(wrcount == len); -} - -static int receive_bytes (uchar chip, char *buf, int len) -{ - volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR; - volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num]; - int dummy = 1; - int rdcount = 0; - int status; - int i; - - mpc_reg_out (®s->mcr, 0, I2C_TX); - - for (i = 0; i < len; ++i) { - buf[rdcount] = mpc_reg_in (®s->mdr); - - if (dummy) { - dummy = 0; - } else { - rdcount++; - } - - if (wait_for_pin (&status)) { - return -4; - } - } - - mpc_reg_out (®s->mcr, I2C_TXAK, I2C_TXAK); - buf[rdcount++] = mpc_reg_in (®s->mdr); - - if (wait_for_pin (&status)) { - return -5; - } - - mpc_reg_out (®s->mcr, 0, I2C_TXAK); - - return 0; -} - -/**************** I2C API ****************/ - -void i2c_init (int speed, int saddr) -{ - volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR; - int i; - - for (i = 0; i < I2C_BUS_CNT; i++){ - volatile i2c512x_dev_t *regs = &im->i2c.dev[i]; - - mpc_reg_out (®s->mcr, 0, 0); - - /* Set clock */ - mpc_reg_out (®s->mfdr, mpc_get_fdr (speed), 0); - mpc_reg_out (®s->madr, saddr << 1, 0); - - /* Enable module */ - mpc_reg_out (®s->mcr, I2C_EN, I2C_INIT_MASK); - mpc_reg_out (®s->msr, 0, I2C_IF); - } - - /* Disable interrupts */ - out_be32(&im->i2c.icr, 0); - - /* Turn off filters */ - out_be32(&im->i2c.mifr, 0); -} - -static int mpc_get_fdr (int speed) -{ - static int fdr = -1; - - if (fdr == -1) { - ulong best_speed = 0; - ulong divider; - ulong ips, scl; - ulong bestmatch = 0xffffffffUL; - int best_i = 0, best_j = 0, i, j; - int SCL_Tap[] = { 9, 10, 12, 15, 5, 6, 7, 8}; - struct mpc512x_i2c_tap scltap[] = { - {4, 1}, - {4, 2}, - {6, 4}, - {6, 8}, - {14, 16}, - {30, 32}, - {62, 64}, - {126, 128} - }; - - ips = gd->arch.ips_clk; - for (i = 7; i >= 0; i--) { - for (j = 7; j >= 0; j--) { - scl = 2 * (scltap[j].scl2tap + - (SCL_Tap[i] - 1) * scltap[j].tap2tap - + 2); - if (ips <= speed*scl) { - if ((speed*scl - ips) < bestmatch) { - bestmatch = speed*scl - ips; - best_i = i; - best_j = j; - best_speed = ips/scl; - } - } - } - } - divider = (best_i & 3) | ((best_i & 4) << 3) | (best_j << 2); - if (gd->flags & GD_FLG_RELOC) { - fdr = divider; - } else { - debug("%ld kHz, \n", best_speed / 1000); - return divider; - } - } - - return fdr; -} - -int i2c_probe (uchar chip) -{ - volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR; - volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num]; - int i; - - for (i = 0; i < I2C_RETRIES; i++) { - mpc_reg_out (®s->mcr, I2C_STA, I2C_STA); - - if (! do_address (chip, 0)) { - mpc_reg_out (®s->mcr, 0, I2C_STA); - udelay (500); - break; - } - - mpc_reg_out (®s->mcr, 0, I2C_STA); - udelay (500); - } - - return (i == I2C_RETRIES); -} - -int i2c_read (uchar chip, uint addr, int alen, uchar *buf, int len) -{ - volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR; - volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num]; - char xaddr[4]; - int ret = -1; - - xaddr[0] = (addr >> 24) & 0xFF; - xaddr[1] = (addr >> 16) & 0xFF; - xaddr[2] = (addr >> 8) & 0xFF; - xaddr[3] = addr & 0xFF; - - if (wait_for_bb ()) { - printf ("i2c_read: bus is busy\n"); - goto Done; - } - - mpc_reg_out (®s->mcr, I2C_STA, I2C_STA); - if (do_address (chip, 0)) { - printf ("i2c_read: failed to address chip\n"); - goto Done; - } - - if (send_bytes (chip, &xaddr[4-alen], alen)) { - printf ("i2c_read: send_bytes failed\n"); - goto Done; - } - - mpc_reg_out (®s->mcr, I2C_RSTA, I2C_RSTA); - if (do_address (chip, 1)) { - printf ("i2c_read: failed to address chip\n"); - goto Done; - } - - if (receive_bytes (chip, (char *)buf, len)) { - printf ("i2c_read: receive_bytes failed\n"); - goto Done; - } - - ret = 0; -Done: - mpc_reg_out (®s->mcr, 0, I2C_STA); - return ret; -} - -int i2c_write (uchar chip, uint addr, int alen, uchar *buf, int len) -{ - volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR; - volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num]; - char xaddr[4]; - int ret = -1; - - xaddr[0] = (addr >> 24) & 0xFF; - xaddr[1] = (addr >> 16) & 0xFF; - xaddr[2] = (addr >> 8) & 0xFF; - xaddr[3] = addr & 0xFF; - - if (wait_for_bb ()) { - printf ("i2c_write: bus is busy\n"); - goto Done; - } - - mpc_reg_out (®s->mcr, I2C_STA, I2C_STA); - if (do_address (chip, 0)) { - printf ("i2c_write: failed to address chip\n"); - goto Done; - } - - if (send_bytes (chip, &xaddr[4-alen], alen)) { - printf ("i2c_write: send_bytes failed\n"); - goto Done; - } - - if (send_bytes (chip, (char *)buf, len)) { - printf ("i2c_write: send_bytes failed\n"); - goto Done; - } - - ret = 0; -Done: - mpc_reg_out (®s->mcr, 0, I2C_STA); - return ret; -} - -int i2c_set_bus_num (unsigned int bus) -{ - if (bus >= I2C_BUS_CNT) { - return -1; - } - bus_num = bus; - - return 0; -} - -unsigned int i2c_get_bus_num (void) -{ - return bus_num; -} - -#endif /* CONFIG_HARD_I2C */ diff --git a/arch/powerpc/cpu/mpc5xxx/Makefile b/arch/powerpc/cpu/mpc5xxx/Makefile index 5c67e1d37d..88e3b2e3ae 100644 --- a/arch/powerpc/cpu/mpc5xxx/Makefile +++ b/arch/powerpc/cpu/mpc5xxx/Makefile @@ -9,7 +9,6 @@ extra-y = start.o extra-y += traps.o obj-y += io.o obj-y += firmware_sc_task_bestcomm.impl.o -obj-y += i2c.o obj-y += cpu.o obj-y += cpu_init.o obj-y += ide.o diff --git a/arch/powerpc/cpu/mpc5xxx/i2c.c b/arch/powerpc/cpu/mpc5xxx/i2c.c deleted file mode 100644 index 73601ae184..0000000000 --- a/arch/powerpc/cpu/mpc5xxx/i2c.c +++ /dev/null @@ -1,456 +0,0 @@ -/* - * (C) Copyright 2003 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> - -DECLARE_GLOBAL_DATA_PTR; - -#ifdef CONFIG_HARD_I2C - -#include <mpc5xxx.h> -#include <i2c.h> - -#if !defined(CONFIG_I2C_MULTI_BUS) -#if (CONFIG_SYS_I2C_MODULE == 2) -#define I2C_BASE MPC5XXX_I2C2 -#elif (CONFIG_SYS_I2C_MODULE == 1) -#define I2C_BASE MPC5XXX_I2C1 -#else -#error CONFIG_SYS_I2C_MODULE is not properly configured -#endif -#else -static unsigned int i2c_bus_num __attribute__ ((section (".data"))) = - CONFIG_SYS_SPD_BUS_NUM; -static unsigned int i2c_bus_speed[2] = {CONFIG_SYS_I2C_SPEED, - CONFIG_SYS_I2C_SPEED}; - -static const unsigned long i2c_dev[2] = { - MPC5XXX_I2C1, - MPC5XXX_I2C2, -}; - -#define I2C_BASE ((struct mpc5xxx_i2c *)i2c_dev[i2c_bus_num]) -#endif - -#define I2C_TIMEOUT 6667 -#define I2C_RETRIES 3 - -struct mpc5xxx_i2c_tap { - int scl2tap; - int tap2tap; -}; - -static int mpc_reg_in (volatile u32 *reg); -static void mpc_reg_out (volatile u32 *reg, int val, int mask); -static int wait_for_bb (void); -static int wait_for_pin (int *status); -static int do_address (uchar chip, char rdwr_flag); -static int send_bytes (uchar chip, char *buf, int len); -static int receive_bytes (uchar chip, char *buf, int len); -static int mpc_get_fdr (int); - -static int mpc_reg_in(volatile u32 *reg) -{ - int ret = *reg >> 24; - __asm__ __volatile__ ("eieio"); - return ret; -} - -static void mpc_reg_out(volatile u32 *reg, int val, int mask) -{ - int tmp; - - if (!mask) { - *reg = val << 24; - } else { - tmp = mpc_reg_in(reg); - *reg = ((tmp & ~mask) | (val & mask)) << 24; - } - __asm__ __volatile__ ("eieio"); - - return; -} - -static int wait_for_bb(void) -{ - struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE; - int timeout = I2C_TIMEOUT; - int status; - - status = mpc_reg_in(®s->msr); - - while (timeout-- && (status & I2C_BB)) { - mpc_reg_out(®s->mcr, I2C_STA, I2C_STA); - (void)mpc_reg_in(®s->mdr); - mpc_reg_out(®s->mcr, 0, I2C_STA); - mpc_reg_out(®s->mcr, 0, 0); - mpc_reg_out(®s->mcr, I2C_EN, 0); - udelay(15); - status = mpc_reg_in(®s->msr); - } - - return (status & I2C_BB); -} - -static int wait_for_pin(int *status) -{ - struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE; - int timeout = I2C_TIMEOUT; - - *status = mpc_reg_in(®s->msr); - - while (timeout-- && !(*status & I2C_IF)) { - udelay(15); - *status = mpc_reg_in(®s->msr); - } - - if (!(*status & I2C_IF)) { - return -1; - } - - mpc_reg_out(®s->msr, 0, I2C_IF); - - return 0; -} - -static int do_address(uchar chip, char rdwr_flag) -{ - struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE; - int status; - - chip <<= 1; - - if (rdwr_flag) { - chip |= 1; - } - - mpc_reg_out(®s->mcr, I2C_TX, I2C_TX); - mpc_reg_out(®s->mdr, chip, 0); - - if (wait_for_pin(&status)) { - return -2; - } - - if (status & I2C_RXAK) { - return -3; - } - - return 0; -} - -static int send_bytes(uchar chip, char *buf, int len) -{ - struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE; - int wrcount; - int status; - - for (wrcount = 0; wrcount < len; ++wrcount) { - - mpc_reg_out(®s->mdr, buf[wrcount], 0); - - if (wait_for_pin(&status)) { - break; - } - - if (status & I2C_RXAK) { - break; - } - - } - - return !(wrcount == len); -} - -static int receive_bytes(uchar chip, char *buf, int len) -{ - struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE; - int dummy = 1; - int rdcount = 0; - int status; - int i; - - mpc_reg_out(®s->mcr, 0, I2C_TX); - - for (i = 0; i < len; ++i) { - buf[rdcount] = mpc_reg_in(®s->mdr); - - if (dummy) { - dummy = 0; - } else { - rdcount++; - } - - - if (wait_for_pin(&status)) { - return -4; - } - } - - mpc_reg_out(®s->mcr, I2C_TXAK, I2C_TXAK); - buf[rdcount++] = mpc_reg_in(®s->mdr); - - if (wait_for_pin(&status)) { - return -5; - } - - mpc_reg_out(®s->mcr, 0, I2C_TXAK); - - return 0; -} - -#if defined(CONFIG_SYS_I2C_INIT_MPC5XXX) - -#define FDR510(x) (u8) (((x & 0x20) >> 3) | (x & 0x3)) -#define FDR432(x) (u8) ((x & 0x1C) >> 2) -/* - * Reset any i2c devices that may have been interrupted during a system reset. - * Normally this would be accomplished by clocking the line until SCL and SDA - * are released and then sending a start condtiion (From an Atmel datasheet). - * There is no direct access to the i2c pins so instead create start commands - * through the i2c interface. Send a start command then delay for the SDA Hold - * time, repeat this by disabling/enabling the bus a total of 9 times. - */ -static void send_reset(void) -{ - struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE; - int i; - u32 delay; - u8 fdr; - int SDA_Tap[] = { 3, 3, 4, 4, 1, 1, 2, 2}; - struct mpc5xxx_i2c_tap scltap[] = { - {4, 1}, - {4, 2}, - {6, 4}, - {6, 8}, - {14, 16}, - {30, 32}, - {62, 64}, - {126, 128} - }; - - fdr = (u8)mpc_reg_in(®s->mfdr); - - delay = scltap[FDR432(fdr)].scl2tap + ((SDA_Tap[FDR510(fdr)] - 1) * \ - scltap[FDR432(fdr)].tap2tap) + 3; - - for (i = 0; i < 9; i++) { - mpc_reg_out(®s->mcr, I2C_EN|I2C_STA|I2C_TX, I2C_INIT_MASK); - udelay(delay); - mpc_reg_out(®s->mcr, 0, I2C_INIT_MASK); - udelay(delay); - } - - mpc_reg_out(®s->mcr, I2C_EN, I2C_INIT_MASK); -} -#endif /* CONFIG_SYS_I2c_INIT_MPC5XXX */ - -/**************** I2C API ****************/ - -void i2c_init(int speed, int saddr) -{ - struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE; - - mpc_reg_out(®s->mcr, 0, 0); - mpc_reg_out(®s->madr, saddr << 1, 0); - - /* Set clock - */ - mpc_reg_out(®s->mfdr, mpc_get_fdr(speed), 0); - - /* Enable module - */ - mpc_reg_out(®s->mcr, I2C_EN, I2C_INIT_MASK); - mpc_reg_out(®s->msr, 0, I2C_IF); - -#if defined(CONFIG_SYS_I2C_INIT_MPC5XXX) - send_reset(); -#endif - return; -} - -static int mpc_get_fdr(int speed) -{ - static int fdr = -1; - - if (fdr == -1) { - ulong best_speed = 0; - ulong divider; - ulong ipb, scl; - ulong bestmatch = 0xffffffffUL; - int best_i = 0, best_j = 0, i, j; - int SCL_Tap[] = { 9, 10, 12, 15, 5, 6, 7, 8}; - struct mpc5xxx_i2c_tap scltap[] = { - {4, 1}, - {4, 2}, - {6, 4}, - {6, 8}, - {14, 16}, - {30, 32}, - {62, 64}, - {126, 128} - }; - - ipb = gd->arch.ipb_clk; - for (i = 7; i >= 0; i--) { - for (j = 7; j >= 0; j--) { - scl = 2 * (scltap[j].scl2tap + - (SCL_Tap[i] - 1) * scltap[j].tap2tap + 2); - if (ipb <= speed*scl) { - if ((speed*scl - ipb) < bestmatch) { - bestmatch = speed*scl - ipb; - best_i = i; - best_j = j; - best_speed = ipb/scl; - } - } - } - } - divider = (best_i & 3) | ((best_i & 4) << 3) | (best_j << 2); - if (gd->flags & GD_FLG_RELOC) { - fdr = divider; - } else { - printf("%ld kHz, ", best_speed / 1000); - return divider; - } - } - - return fdr; -} - -int i2c_probe(uchar chip) -{ - struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE; - int i; - - for (i = 0; i < I2C_RETRIES; i++) { - mpc_reg_out(®s->mcr, I2C_STA, I2C_STA); - - if (! do_address(chip, 0)) { - mpc_reg_out(®s->mcr, 0, I2C_STA); - udelay(500); - break; - } - - mpc_reg_out(®s->mcr, 0, I2C_STA); - udelay(500); - } - - return (i == I2C_RETRIES); -} - -int i2c_read(uchar chip, uint addr, int alen, uchar *buf, int len) -{ - char xaddr[4]; - struct mpc5xxx_i2c * regs = (struct mpc5xxx_i2c *)I2C_BASE; - int ret = -1; - - xaddr[0] = (addr >> 24) & 0xFF; - xaddr[1] = (addr >> 16) & 0xFF; - xaddr[2] = (addr >> 8) & 0xFF; - xaddr[3] = addr & 0xFF; - - if (wait_for_bb()) { - printf("i2c_read: bus is busy\n"); - goto Done; - } - - mpc_reg_out(®s->mcr, I2C_STA, I2C_STA); - if (do_address(chip, 0)) { - printf("i2c_read: failed to address chip\n"); - goto Done; - } - - if (send_bytes(chip, &xaddr[4-alen], alen)) { - printf("i2c_read: send_bytes failed\n"); - goto Done; - } - - mpc_reg_out(®s->mcr, I2C_RSTA, I2C_RSTA); - if (do_address(chip, 1)) { - printf("i2c_read: failed to address chip\n"); - goto Done; - } - - if (receive_bytes(chip, (char *)buf, len)) { - printf("i2c_read: receive_bytes failed\n"); - goto Done; - } - - ret = 0; -Done: - mpc_reg_out(®s->mcr, 0, I2C_STA); - return ret; -} - -int i2c_write(uchar chip, uint addr, int alen, uchar *buf, int len) -{ - char xaddr[4]; - struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE; - int ret = -1; - - xaddr[0] = (addr >> 24) & 0xFF; - xaddr[1] = (addr >> 16) & 0xFF; - xaddr[2] = (addr >> 8) & 0xFF; - xaddr[3] = addr & 0xFF; - - if (wait_for_bb()) { - printf("i2c_write: bus is busy\n"); - goto Done; - } - - mpc_reg_out(®s->mcr, I2C_STA, I2C_STA); - if (do_address(chip, 0)) { - printf("i2c_write: failed to address chip\n"); - goto Done; - } - - if (send_bytes(chip, &xaddr[4-alen], alen)) { - printf("i2c_write: send_bytes failed\n"); - goto Done; - } - - if (send_bytes(chip, (char *)buf, len)) { - printf("i2c_write: send_bytes failed\n"); - goto Done; - } - - ret = 0; -Done: - mpc_reg_out(®s->mcr, 0, I2C_STA); - return ret; -} - -#if defined(CONFIG_I2C_MULTI_BUS) -int i2c_set_bus_num(unsigned int bus) -{ - if (bus > 1) - return -1; - - i2c_bus_num = bus; - i2c_init(i2c_bus_speed[bus], CONFIG_SYS_I2C_SLAVE); - return 0; -} - -int i2c_set_bus_speed(unsigned int speed) -{ - i2c_init(speed, CONFIG_SYS_I2C_SLAVE); - return 0; -} - -unsigned int i2c_get_bus_num(void) -{ - return i2c_bus_num; -} - -unsigned int i2c_get_bus_speed(void) -{ - return i2c_bus_speed[i2c_bus_num]; -} -#endif - - -#endif /* CONFIG_HARD_I2C */ diff --git a/arch/powerpc/cpu/mpc8260/Makefile b/arch/powerpc/cpu/mpc8260/Makefile index 83adc4c436..72dd8aba25 100644 --- a/arch/powerpc/cpu/mpc8260/Makefile +++ b/arch/powerpc/cpu/mpc8260/Makefile @@ -7,7 +7,7 @@ extra-y = start.o obj-y = traps.o serial_smc.o serial_scc.o cpu.o cpu_init.o speed.o \ - interrupts.o ether_fcc.o i2c.o commproc.o \ + interrupts.o ether_fcc.o commproc.o \ bedbug_603e.o pci.o spi.o kgdb.o obj-$(CONFIG_ETHER_ON_SCC) += ether_scc.o diff --git a/arch/powerpc/cpu/mpc8260/commproc.c b/arch/powerpc/cpu/mpc8260/commproc.c index 484bd17745..ff69881089 100644 --- a/arch/powerpc/cpu/mpc8260/commproc.c +++ b/arch/powerpc/cpu/mpc8260/commproc.c @@ -41,10 +41,6 @@ m8260_cpm_reset(void) do { /* Spin until command processed */ __asm__ __volatile__ ("eieio"); } while ((immr->im_cpm.cp_cpcr & CPM_CR_FLG) && ++count < 1000000); - -#ifdef CONFIG_HARD_I2C - immr->im_dprambase16[PROFF_I2C_BASE / sizeof(u16)] = 0; -#endif } /* Allocate some memory from the dual ported ram. diff --git a/arch/powerpc/cpu/mpc8260/i2c.c b/arch/powerpc/cpu/mpc8260/i2c.c deleted file mode 100644 index a0de101329..0000000000 --- a/arch/powerpc/cpu/mpc8260/i2c.c +++ /dev/null @@ -1,741 +0,0 @@ -/* - * (C) Copyright 2000 - * Paolo Scaffardi, AIRVENT SAM s.p.a - RIMINI(ITALY), arsenio@tin.it - * - * (C) Copyright 2000 Sysgo Real-Time Solutions, GmbH <www.elinos.com> - * Marius Groeger <mgroeger@sysgo.de> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <console.h> - -#if defined(CONFIG_HARD_I2C) - -#include <asm/cpm_8260.h> -#include <i2c.h> - -DECLARE_GLOBAL_DATA_PTR; - -#if defined(CONFIG_I2C_MULTI_BUS) -static unsigned int i2c_bus_num __attribute__ ((section(".data"))) = 0; -#endif /* CONFIG_I2C_MULTI_BUS */ - -/* uSec to wait between polls of the i2c */ -#define DELAY_US 100 -/* uSec to wait for the CPM to start processing the buffer */ -#define START_DELAY_US 1000 - -/* - * tx/rx per-byte timeout: we delay DELAY_US uSec between polls so the - * timeout will be (tx_length + rx_length) * DELAY_US * TOUT_LOOP - */ -#define TOUT_LOOP 5 - -/* - * Set default values - */ -#ifndef CONFIG_SYS_I2C_SPEED -#define CONFIG_SYS_I2C_SPEED 50000 -#endif - - -typedef void (*i2c_ecb_t) (int, int, void *); /* error callback function */ - -/* This structure keeps track of the bd and buffer space usage. */ -typedef struct i2c_state { - int rx_idx; /* index to next free Rx BD */ - int tx_idx; /* index to next free Tx BD */ - void *rxbd; /* pointer to next free Rx BD */ - void *txbd; /* pointer to next free Tx BD */ - int tx_space; /* number of Tx bytes left */ - unsigned char *tx_buf; /* pointer to free Tx area */ - i2c_ecb_t err_cb; /* error callback function */ - void *cb_data; /* private data to be passed */ -} i2c_state_t; - -/* flags for i2c_send() and i2c_receive() */ -#define I2CF_ENABLE_SECONDARY 0x01 /* secondary_address is valid */ -#define I2CF_START_COND 0x02 /* tx: generate start condition */ -#define I2CF_STOP_COND 0x04 /* tx: generate stop condition */ - -/* return codes */ -#define I2CERR_NO_BUFFERS 1 /* no more BDs or buffer space */ -#define I2CERR_MSG_TOO_LONG 2 /* tried to send/receive to much data */ -#define I2CERR_TIMEOUT 3 /* timeout in i2c_doio() */ -#define I2CERR_QUEUE_EMPTY 4 /* i2c_doio called without send/rcv */ -#define I2CERR_IO_ERROR 5 /* had an error during comms */ - -/* error callback flags */ -#define I2CECB_RX_ERR 0x10 /* this is a receive error */ -#define I2CECB_RX_OV 0x02 /* receive overrun error */ -#define I2CECB_RX_MASK 0x0f /* mask for error bits */ -#define I2CECB_TX_ERR 0x20 /* this is a transmit error */ -#define I2CECB_TX_CL 0x01 /* transmit collision error */ -#define I2CECB_TX_UN 0x02 /* transmit underflow error */ -#define I2CECB_TX_NAK 0x04 /* transmit no ack error */ -#define I2CECB_TX_MASK 0x0f /* mask for error bits */ -#define I2CECB_TIMEOUT 0x40 /* this is a timeout error */ - -#define ERROR_I2C_NONE 0 -#define ERROR_I2C_LENGTH 1 - -#define I2C_WRITE_BIT 0x00 -#define I2C_READ_BIT 0x01 - -#define I2C_RXTX_LEN 128 /* maximum tx/rx buffer length */ - - -#define NUM_RX_BDS 4 -#define NUM_TX_BDS 4 -#define MAX_TX_SPACE 256 - -typedef struct I2C_BD { - unsigned short status; - unsigned short length; - unsigned char *addr; -} I2C_BD; - -#define BD_I2C_TX_START 0x0400 /* special status for i2c: Start condition */ - -#define BD_I2C_TX_CL 0x0001 /* collision error */ -#define BD_I2C_TX_UN 0x0002 /* underflow error */ -#define BD_I2C_TX_NAK 0x0004 /* no acknowledge error */ -#define BD_I2C_TX_ERR (BD_I2C_TX_NAK|BD_I2C_TX_UN|BD_I2C_TX_CL) - -#define BD_I2C_RX_ERR BD_SC_OV - -/* - * Returns the best value of I2BRG to meet desired clock speed of I2C with - * input parameters (clock speed, filter, and predivider value). - * It returns computer speed value and the difference between it and desired - * speed. - */ -static inline int -i2c_roundrate(int hz, int speed, int filter, int modval, - int *brgval, int *totspeed) -{ - int moddiv = 1 << (5 - (modval & 3)), brgdiv, div; - - debug("\t[I2C] trying hz=%d, speed=%d, filter=%d, modval=%d\n", - hz, speed, filter, modval); - - div = moddiv * speed; - brgdiv = (hz + div - 1) / div; - - debug("\t\tmoddiv=%d, brgdiv=%d\n", moddiv, brgdiv); - - *brgval = ((brgdiv + 1) / 2) - 3 - (2 * filter); - - if ((*brgval < 0) || (*brgval > 255)) { - debug("\t\trejected brgval=%d\n", *brgval); - return -1; - } - - brgdiv = 2 * (*brgval + 3 + (2 * filter)); - div = moddiv * brgdiv; - *totspeed = hz / div; - - debug("\t\taccepted brgval=%d, totspeed=%d\n", *brgval, *totspeed); - - return 0; -} - -/* - * Sets the I2C clock predivider and divider to meet required clock speed. - */ -static int i2c_setrate(int hz, int speed) -{ - immap_t *immap = (immap_t *)CONFIG_SYS_IMMR; - volatile i2c8260_t *i2c = (i2c8260_t *)&immap->im_i2c; - int brgval, - modval, /* 0-3 */ - bestspeed_diff = speed, - bestspeed_brgval = 0, - bestspeed_modval = 0, - bestspeed_filter = 0, - totspeed, - filter = 0; /* Use this fixed value */ - - for (modval = 0; modval < 4; modval++) { - if (i2c_roundrate(hz, speed, filter, modval, &brgval, &totspeed) - == 0) { - int diff = speed - totspeed; - - if ((diff >= 0) && (diff < bestspeed_diff)) { - bestspeed_diff = diff; - bestspeed_modval = modval; - bestspeed_brgval = brgval; - bestspeed_filter = filter; - } - } - } - - debug("[I2C] Best is:\n"); - debug("[I2C] CPU=%dhz RATE=%d F=%d I2MOD=%08x I2BRG=%08x DIFF=%dhz\n", - hz, speed, bestspeed_filter, bestspeed_modval, bestspeed_brgval, - bestspeed_diff); - - i2c->i2c_i2mod |= ((bestspeed_modval & 3) << 1) | - (bestspeed_filter << 3); - i2c->i2c_i2brg = bestspeed_brgval & 0xff; - - debug("[I2C] i2mod=%08x i2brg=%08x\n", i2c->i2c_i2mod, - i2c->i2c_i2brg); - - return 1; -} - -void i2c_init(int speed, int slaveadd) -{ - volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR; - volatile cpm8260_t *cp = (cpm8260_t *)&immap->im_cpm; - volatile i2c8260_t *i2c = (i2c8260_t *)&immap->im_i2c; - volatile iic_t *iip; - ulong rbase, tbase; - volatile I2C_BD *rxbd, *txbd; - uint dpaddr; - -#ifdef CONFIG_SYS_I2C_INIT_BOARD - /* - * call board specific i2c bus reset routine before accessing the - * environment, which might be in a chip on that bus. For details - * about this problem see doc/I2C_Edge_Conditions. - */ - i2c_init_board(); -#endif - - dpaddr = immap->im_dprambase16[PROFF_I2C_BASE / sizeof(u16)]; - if (dpaddr == 0) { - /* need to allocate dual port ram */ - dpaddr = m8260_cpm_dpalloc(64 + - (NUM_RX_BDS * sizeof(I2C_BD)) + - (NUM_TX_BDS * sizeof(I2C_BD)) + - MAX_TX_SPACE, 64); - immap->im_dprambase16[PROFF_I2C_BASE / sizeof(u16)] = - dpaddr; - } - - /* - * initialise data in dual port ram: - * - * dpaddr -> parameter ram (64 bytes) - * rbase -> rx BD (NUM_RX_BDS * sizeof(I2C_BD) bytes) - * tbase -> tx BD (NUM_TX_BDS * sizeof(I2C_BD) bytes) - * tx buffer (MAX_TX_SPACE bytes) - */ - - iip = (iic_t *)&immap->im_dprambase[dpaddr]; - memset((void *)iip, 0, sizeof(iic_t)); - - rbase = dpaddr + 64; - tbase = rbase + NUM_RX_BDS * sizeof(I2C_BD); - - /* Disable interrupts */ - i2c->i2c_i2mod = 0x00; - i2c->i2c_i2cmr = 0x00; - i2c->i2c_i2cer = 0xff; - i2c->i2c_i2add = slaveadd; - - /* - * Set the I2C BRG Clock division factor from desired i2c rate - * and current CPU rate (we assume sccr dfbgr field is 0; - * divide BRGCLK by 1) - */ - debug("[I2C] Setting rate...\n"); - i2c_setrate(gd->arch.brg_clk, CONFIG_SYS_I2C_SPEED); - - /* Set I2C controller in master mode */ - i2c->i2c_i2com = 0x01; - - /* Initialize Tx/Rx parameters */ - iip->iic_rbase = rbase; - iip->iic_tbase = tbase; - rxbd = (I2C_BD *)((unsigned char *) &immap-> - im_dprambase[iip->iic_rbase]); - txbd = (I2C_BD *)((unsigned char *) &immap-> - im_dprambase[iip->iic_tbase]); - - debug("[I2C] rbase = %04x\n", iip->iic_rbase); - debug("[I2C] tbase = %04x\n", iip->iic_tbase); - debug("[I2C] rxbd = %08x\n", (int) rxbd); - debug("[I2C] txbd = %08x\n", (int) txbd); - - /* Set big endian byte order */ - iip->iic_tfcr = 0x10; - iip->iic_rfcr = 0x10; - - /* Set maximum receive size. */ - iip->iic_mrblr = I2C_RXTX_LEN; - - cp->cp_cpcr = mk_cr_cmd(CPM_CR_I2C_PAGE, - CPM_CR_I2C_SBLOCK, - 0x00, CPM_CR_INIT_TRX) | CPM_CR_FLG; - do { - __asm__ __volatile__("eieio"); - } while (cp->cp_cpcr & CPM_CR_FLG); - - /* Clear events and interrupts */ - i2c->i2c_i2cer = 0xff; - i2c->i2c_i2cmr = 0x00; -} - -static -void i2c_newio(i2c_state_t *state) -{ - volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR; - volatile iic_t *iip; - uint dpaddr; - - debug("[I2C] i2c_newio\n"); - - dpaddr = immap->im_dprambase16[PROFF_I2C_BASE / sizeof(u16)]; - iip = (iic_t *)&immap->im_dprambase[dpaddr]; - state->rx_idx = 0; - state->tx_idx = 0; - state->rxbd = (void *)&immap->im_dprambase[iip->iic_rbase]; - state->txbd = (void *)&immap->im_dprambase[iip->iic_tbase]; - state->tx_space = MAX_TX_SPACE; - state->tx_buf = (uchar *)state->txbd + NUM_TX_BDS * sizeof(I2C_BD); - state->err_cb = NULL; - state->cb_data = NULL; - - debug("[I2C] rxbd = %08x\n", (int)state->rxbd); - debug("[I2C] txbd = %08x\n", (int)state->txbd); - debug("[I2C] tx_buf = %08x\n", (int)state->tx_buf); - - /* clear the buffer memory */ - memset((char *) state->tx_buf, 0, MAX_TX_SPACE); -} - -static -int i2c_send(i2c_state_t *state, - unsigned char address, - unsigned char secondary_address, - unsigned int flags, unsigned short size, unsigned char *dataout) -{ - volatile I2C_BD *txbd; - int i, j; - - debug("[I2C] i2c_send add=%02d sec=%02d flag=%02d size=%d\n", - address, secondary_address, flags, size); - - /* trying to send message larger than BD */ - if (size > I2C_RXTX_LEN) - return I2CERR_MSG_TOO_LONG; - - /* no more free bds */ - if (state->tx_idx >= NUM_TX_BDS || state->tx_space < (2 + size)) - return I2CERR_NO_BUFFERS; - - txbd = (I2C_BD *)state->txbd; - txbd->addr = state->tx_buf; - - debug("[I2C] txbd = %08x\n", (int) txbd); - - if (flags & I2CF_START_COND) { - debug("[I2C] Formatting addresses...\n"); - if (flags & I2CF_ENABLE_SECONDARY) { - /* Length of message plus dest addresses */ - txbd->length = size + 2; - txbd->addr[0] = address << 1; - txbd->addr[1] = secondary_address; - i = 2; - } else { - /* Length of message plus dest address */ - txbd->length = size + 1; - /* Write destination address to BD */ - txbd->addr[0] = address << 1; - i = 1; - } - } else { - txbd->length = size; /* Length of message */ - i = 0; - } - - /* set up txbd */ - txbd->status = BD_SC_READY; - if (flags & I2CF_START_COND) - txbd->status |= BD_I2C_TX_START; - if (flags & I2CF_STOP_COND) - txbd->status |= BD_SC_LAST | BD_SC_WRAP; - - /* Copy data to send into buffer */ - debug("[I2C] copy data...\n"); - for (j = 0; j < size; i++, j++) - txbd->addr[i] = dataout[j]; - - debug("[I2C] txbd: length=0x%04x status=0x%04x addr[0]=0x%02x addr[1]=0x%02x\n", - txbd->length, txbd->status, txbd->addr[0], txbd->addr[1]); - - /* advance state */ - state->tx_buf += txbd->length; - state->tx_space -= txbd->length; - state->tx_idx++; - state->txbd = (void *) (txbd + 1); - - return 0; -} - -static -int i2c_receive(i2c_state_t *state, - unsigned char address, - unsigned char secondary_address, - unsigned int flags, - unsigned short size_to_expect, unsigned char *datain) -{ - volatile I2C_BD *rxbd, *txbd; - - debug("[I2C] i2c_receive %02d %02d %02d\n", address, - secondary_address, flags); - - /* Expected to receive too much */ - if (size_to_expect > I2C_RXTX_LEN) - return I2CERR_MSG_TOO_LONG; - - /* no more free bds */ - if (state->tx_idx >= NUM_TX_BDS || state->rx_idx >= NUM_RX_BDS - || state->tx_space < 2) - return I2CERR_NO_BUFFERS; - - rxbd = (I2C_BD *) state->rxbd; - txbd = (I2C_BD *) state->txbd; - - debug("[I2C] rxbd = %08x\n", (int) rxbd); - debug("[I2C] txbd = %08x\n", (int) txbd); - - txbd->addr = state->tx_buf; - - /* set up TXBD for destination address */ - if (flags & I2CF_ENABLE_SECONDARY) { - txbd->length = 2; - txbd->addr[0] = address << 1; /* Write data */ - txbd->addr[1] = secondary_address; /* Internal address */ - txbd->status = BD_SC_READY; - } else { - txbd->length = 1 + size_to_expect; - txbd->addr[0] = (address << 1) | 0x01; - txbd->status = BD_SC_READY; - memset(&txbd->addr[1], 0, txbd->length); - } - - /* set up rxbd for reception */ - rxbd->status = BD_SC_EMPTY; - rxbd->length = size_to_expect; - rxbd->addr = datain; - - txbd->status |= BD_I2C_TX_START; - if (flags & I2CF_STOP_COND) { - txbd->status |= BD_SC_LAST | BD_SC_WRAP; - rxbd->status |= BD_SC_WRAP; - } - - debug("[I2C] txbd: length=0x%04x status=0x%04x addr[0]=0x%02x addr[1]=0x%02x\n", - txbd->length, txbd->status, txbd->addr[0], txbd->addr[1]); - debug("[I2C] rxbd: length=0x%04x status=0x%04x addr[0]=0x%02x addr[1]=0x%02x\n", - rxbd->length, rxbd->status, rxbd->addr[0], rxbd->addr[1]); - - /* advance state */ - state->tx_buf += txbd->length; - state->tx_space -= txbd->length; - state->tx_idx++; - state->txbd = (void *) (txbd + 1); - state->rx_idx++; - state->rxbd = (void *) (rxbd + 1); - - return 0; -} - - -static -int i2c_doio(i2c_state_t *state) -{ - volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR; - volatile iic_t *iip; - volatile i2c8260_t *i2c = (i2c8260_t *)&immap->im_i2c; - volatile I2C_BD *txbd, *rxbd; - int n, i, b, rxcnt = 0, rxtimeo = 0, txcnt = 0, txtimeo = 0, rc = 0; - uint dpaddr; - - debug("[I2C] i2c_doio\n"); - - if (state->tx_idx <= 0 && state->rx_idx <= 0) { - debug("[I2C] No I/O is queued\n"); - return I2CERR_QUEUE_EMPTY; - } - - dpaddr = immap->im_dprambase16[PROFF_I2C_BASE / sizeof(u16)]; - iip = (iic_t *)&immap->im_dprambase[dpaddr]; - iip->iic_rbptr = iip->iic_rbase; - iip->iic_tbptr = iip->iic_tbase; - - /* Enable I2C */ - debug("[I2C] Enabling I2C...\n"); - i2c->i2c_i2mod |= 0x01; - - /* Begin transmission */ - i2c->i2c_i2com |= 0x80; - - /* Loop until transmit & receive completed */ - - n = state->tx_idx; - - if (n > 0) { - - txbd = ((I2C_BD *) state->txbd) - n; - for (i = 0; i < n; i++) { - txtimeo += TOUT_LOOP * txbd->length; - txbd++; - } - - txbd--; /* wait until last in list is done */ - - debug("[I2C] Transmitting...(txbd=0x%08lx)\n", - (ulong) txbd); - - udelay(START_DELAY_US); /* give it time to start */ - while ((txbd->status & BD_SC_READY) && (++txcnt < txtimeo)) { - udelay(DELAY_US); - if (ctrlc()) - return -1; - __asm__ __volatile__("eieio"); - } - } - - n = state->rx_idx; - - if (txcnt < txtimeo && n > 0) { - - rxbd = ((I2C_BD *) state->rxbd) - n; - for (i = 0; i < n; i++) { - rxtimeo += TOUT_LOOP * rxbd->length; - rxbd++; - } - - rxbd--; /* wait until last in list is done */ - - debug("[I2C] Receiving...(rxbd=0x%08lx)\n", (ulong) rxbd); - - udelay(START_DELAY_US); /* give it time to start */ - while ((rxbd->status & BD_SC_EMPTY) && (++rxcnt < rxtimeo)) { - udelay(DELAY_US); - if (ctrlc()) - return -1; - __asm__ __volatile__("eieio"); - } - } - - /* Turn off I2C */ - i2c->i2c_i2mod &= ~0x01; - - n = state->tx_idx; - - if (n > 0) { - for (i = 0; i < n; i++) { - txbd = ((I2C_BD *) state->txbd) - (n - i); - b = txbd->status & BD_I2C_TX_ERR; - if (b != 0) { - if (state->err_cb != NULL) - (*state->err_cb) (I2CECB_TX_ERR | b, - i, state->cb_data); - if (rc == 0) - rc = I2CERR_IO_ERROR; - } - } - } - - n = state->rx_idx; - - if (n > 0) { - for (i = 0; i < n; i++) { - rxbd = ((I2C_BD *) state->rxbd) - (n - i); - b = rxbd->status & BD_I2C_RX_ERR; - if (b != 0) { - if (state->err_cb != NULL) - (*state->err_cb) (I2CECB_RX_ERR | b, - i, state->cb_data); - if (rc == 0) - rc = I2CERR_IO_ERROR; - } - } - } - - if ((txtimeo > 0 && txcnt >= txtimeo) || - (rxtimeo > 0 && rxcnt >= rxtimeo)) { - if (state->err_cb != NULL) - (*state->err_cb) (I2CECB_TIMEOUT, -1, state->cb_data); - if (rc == 0) - rc = I2CERR_TIMEOUT; - } - - return rc; -} - -static void i2c_probe_callback(int flags, int xnum, void *data) -{ - /* - * the only acceptable errors are a transmit NAK or a receive - * overrun - tx NAK means the device does not exist, rx OV - * means the device must have responded to the slave address - * even though the transfer failed - */ - if (flags == (I2CECB_TX_ERR | I2CECB_TX_NAK)) - *(int *) data |= 1; - if (flags == (I2CECB_RX_ERR | I2CECB_RX_OV)) - *(int *) data |= 2; -} - -int i2c_probe(uchar chip) -{ - i2c_state_t state; - int rc, err_flag; - uchar buf[1]; - - i2c_newio(&state); - - state.err_cb = i2c_probe_callback; - state.cb_data = (void *) &err_flag; - err_flag = 0; - - rc = i2c_receive(&state, chip, 0, I2CF_START_COND | I2CF_STOP_COND, 1, - buf); - - if (rc != 0) - return rc; /* probe failed */ - - rc = i2c_doio(&state); - - if (rc == 0) - return 0; /* device exists - read succeeded */ - - if (rc == I2CERR_TIMEOUT) - return -1; /* device does not exist - timeout */ - - if (rc != I2CERR_IO_ERROR || err_flag == 0) - return rc; /* probe failed */ - - if (err_flag & 1) - return -1; /* device does not exist - had transmit NAK */ - - return 0; /* device exists - had receive overrun */ -} - - -int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len) -{ - i2c_state_t state; - uchar xaddr[4]; - int rc; - - xaddr[0] = (addr >> 24) & 0xFF; - xaddr[1] = (addr >> 16) & 0xFF; - xaddr[2] = (addr >> 8) & 0xFF; - xaddr[3] = addr & 0xFF; - -#ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW - /* - * EEPROM chips that implement "address overflow" are ones - * like Catalyst 24WC04/08/16 which has 9/10/11 bits of address - * and the extra bits end up in the "chip address" bit slots. - * This makes a 24WC08 (1Kbyte) chip look like four 256 byte - * chips. - * - * Note that we consider the length of the address field to still - * be one byte because the extra address bits are hidden in the - * chip address. - */ - chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW); -#endif - - i2c_newio(&state); - - rc = i2c_send(&state, chip, 0, I2CF_START_COND, alen, - &xaddr[4 - alen]); - if (rc != 0) { - printf("i2c_read: i2c_send failed (%d)\n", rc); - return 1; - } - - rc = i2c_receive(&state, chip, 0, I2CF_STOP_COND, len, buffer); - if (rc != 0) { - printf("i2c_read: i2c_receive failed (%d)\n", rc); - return 1; - } - - rc = i2c_doio(&state); - if (rc != 0) { - printf("i2c_read: i2c_doio failed (%d)\n", rc); - return 1; - } - return 0; -} - -int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len) -{ - i2c_state_t state; - uchar xaddr[4]; - int rc; - - xaddr[0] = (addr >> 24) & 0xFF; - xaddr[1] = (addr >> 16) & 0xFF; - xaddr[2] = (addr >> 8) & 0xFF; - xaddr[3] = addr & 0xFF; - -#ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW - /* - * EEPROM chips that implement "address overflow" are ones - * like Catalyst 24WC04/08/16 which has 9/10/11 bits of address - * and the extra bits end up in the "chip address" bit slots. - * This makes a 24WC08 (1Kbyte) chip look like four 256 byte - * chips. - * - * Note that we consider the length of the address field to still - * be one byte because the extra address bits are hidden in the - * chip address. - */ - chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW); -#endif - - i2c_newio(&state); - - rc = i2c_send(&state, chip, 0, I2CF_START_COND, alen, - &xaddr[4 - alen]); - if (rc != 0) { - printf("i2c_write: first i2c_send failed (%d)\n", rc); - return 1; - } - - rc = i2c_send(&state, 0, 0, I2CF_STOP_COND, len, buffer); - if (rc != 0) { - printf("i2c_write: second i2c_send failed (%d)\n", rc); - return 1; - } - - rc = i2c_doio(&state); - if (rc != 0) { - printf("i2c_write: i2c_doio failed (%d)\n", rc); - return 1; - } - return 0; -} - -#if defined(CONFIG_I2C_MULTI_BUS) -/* - * Functions for multiple I2C bus handling - */ -unsigned int i2c_get_bus_num(void) -{ - return i2c_bus_num; -} - -int i2c_set_bus_num(unsigned int bus) -{ - if (bus >= CONFIG_SYS_MAX_I2C_BUS) - return -1; - i2c_bus_num = bus; - return 0; -} - -#endif /* CONFIG_I2C_MULTI_BUS */ -#endif /* CONFIG_HARD_I2C */ diff --git a/arch/powerpc/cpu/mpc8xx/Makefile b/arch/powerpc/cpu/mpc8xx/Makefile index 6f81fee571..fc91a054f0 100644 --- a/arch/powerpc/cpu/mpc8xx/Makefile +++ b/arch/powerpc/cpu/mpc8xx/Makefile @@ -14,7 +14,6 @@ obj-y += cpu.o obj-y += cpu_init.o obj-y += fec.o obj-$(CONFIG_OF_LIBFDT) += fdt.o -obj-y += i2c.o obj-y += interrupts.o obj-y += scc.o obj-y += serial.o diff --git a/arch/powerpc/cpu/mpc8xx/i2c.c b/arch/powerpc/cpu/mpc8xx/i2c.c deleted file mode 100644 index 54d5cb5130..0000000000 --- a/arch/powerpc/cpu/mpc8xx/i2c.c +++ /dev/null @@ -1,672 +0,0 @@ -/* - * (C) Copyright 2000 - * Paolo Scaffardi, AIRVENT SAM s.p.a - RIMINI(ITALY), arsenio@tin.it - * - * (C) Copyright 2000 Sysgo Real-Time Solutions, GmbH <www.elinos.com> - * Marius Groeger <mgroeger@sysgo.de> - * - * SPDX-License-Identifier: GPL-2.0+ - * - * Back ported to the 8xx platform (from the 8260 platform) by - * Murray.Jensen@cmst.csiro.au, 27-Jan-01. - */ - -#include <common.h> -#include <console.h> - -#ifdef CONFIG_HARD_I2C - -#include <commproc.h> -#include <i2c.h> - -DECLARE_GLOBAL_DATA_PTR; - -/* tx/rx timeout (we need the i2c early, so we don't use get_timer()) */ -#define TOUT_LOOP 1000000 - -#define NUM_RX_BDS 4 -#define NUM_TX_BDS 4 -#define MAX_TX_SPACE 256 -#define I2C_RXTX_LEN 128 /* maximum tx/rx buffer length */ - -typedef struct I2C_BD { - unsigned short status; - unsigned short length; - unsigned char *addr; -} I2C_BD; - -#define BD_I2C_TX_START 0x0400 /* special status for i2c: Start condition */ - -#define BD_I2C_TX_CL 0x0001 /* collision error */ -#define BD_I2C_TX_UN 0x0002 /* underflow error */ -#define BD_I2C_TX_NAK 0x0004 /* no acknowledge error */ -#define BD_I2C_TX_ERR (BD_I2C_TX_NAK|BD_I2C_TX_UN|BD_I2C_TX_CL) - -#define BD_I2C_RX_ERR BD_SC_OV - -typedef void (*i2c_ecb_t) (int, int); /* error callback function */ - -/* This structure keeps track of the bd and buffer space usage. */ -typedef struct i2c_state { - int rx_idx; /* index to next free Rx BD */ - int tx_idx; /* index to next free Tx BD */ - void *rxbd; /* pointer to next free Rx BD */ - void *txbd; /* pointer to next free Tx BD */ - int tx_space; /* number of Tx bytes left */ - unsigned char *tx_buf; /* pointer to free Tx area */ - i2c_ecb_t err_cb; /* error callback function */ -} i2c_state_t; - - -/* flags for i2c_send() and i2c_receive() */ -#define I2CF_ENABLE_SECONDARY 0x01 /* secondary_address is valid */ -#define I2CF_START_COND 0x02 /* tx: generate start condition */ -#define I2CF_STOP_COND 0x04 /* tx: generate stop condition */ - -/* return codes */ -#define I2CERR_NO_BUFFERS 0x01 /* no more BDs or buffer space */ -#define I2CERR_MSG_TOO_LONG 0x02 /* tried to send/receive to much data */ -#define I2CERR_TIMEOUT 0x03 /* timeout in i2c_doio() */ -#define I2CERR_QUEUE_EMPTY 0x04 /* i2c_doio called without send/receive */ - -/* error callback flags */ -#define I2CECB_RX_ERR 0x10 /* this is a receive error */ -#define I2CECB_RX_ERR_OV 0x02 /* receive overrun error */ -#define I2CECB_RX_MASK 0x0f /* mask for error bits */ -#define I2CECB_TX_ERR 0x20 /* this is a transmit error */ -#define I2CECB_TX_CL 0x01 /* transmit collision error */ -#define I2CECB_TX_UN 0x02 /* transmit underflow error */ -#define I2CECB_TX_NAK 0x04 /* transmit no ack error */ -#define I2CECB_TX_MASK 0x0f /* mask for error bits */ -#define I2CECB_TIMEOUT 0x40 /* this is a timeout error */ - -/* - * Returns the best value of I2BRG to meet desired clock speed of I2C with - * input parameters (clock speed, filter, and predivider value). - * It returns computer speed value and the difference between it and desired - * speed. - */ -static inline int -i2c_roundrate(int hz, int speed, int filter, int modval, - int *brgval, int *totspeed) -{ - int moddiv = 1 << (5 - (modval & 3)), brgdiv, div; - - debug("\t[I2C] trying hz=%d, speed=%d, filter=%d, modval=%d\n", - hz, speed, filter, modval); - - div = moddiv * speed; - brgdiv = (hz + div - 1) / div; - - debug("\t\tmoddiv=%d, brgdiv=%d\n", moddiv, brgdiv); - - *brgval = ((brgdiv + 1) / 2) - 3 - (2 * filter); - - if ((*brgval < 0) || (*brgval > 255)) { - debug("\t\trejected brgval=%d\n", *brgval); - return -1; - } - - brgdiv = 2 * (*brgval + 3 + (2 * filter)); - div = moddiv * brgdiv; - *totspeed = hz / div; - - debug("\t\taccepted brgval=%d, totspeed=%d\n", *brgval, *totspeed); - - return 0; -} - -/* - * Sets the I2C clock predivider and divider to meet required clock speed. - */ -static int i2c_setrate(int hz, int speed) -{ - immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; - volatile i2c8xx_t *i2c = (i2c8xx_t *) & immap->im_i2c; - int brgval, - modval, /* 0-3 */ - bestspeed_diff = speed, - bestspeed_brgval = 0, - bestspeed_modval = 0, - bestspeed_filter = 0, - totspeed, - filter = 0; /* Use this fixed value */ - - for (modval = 0; modval < 4; modval++) { - if (i2c_roundrate - (hz, speed, filter, modval, &brgval, &totspeed) == 0) { - int diff = speed - totspeed; - - if ((diff >= 0) && (diff < bestspeed_diff)) { - bestspeed_diff = diff; - bestspeed_modval = modval; - bestspeed_brgval = brgval; - bestspeed_filter = filter; - } - } - } - - debug("[I2C] Best is:\n"); - debug("[I2C] CPU=%dhz RATE=%d F=%d I2MOD=%08x I2BRG=%08x DIFF=%dhz\n", - hz, - speed, - bestspeed_filter, - bestspeed_modval, - bestspeed_brgval, - bestspeed_diff); - - i2c->i2c_i2mod |= - ((bestspeed_modval & 3) << 1) | (bestspeed_filter << 3); - i2c->i2c_i2brg = bestspeed_brgval & 0xff; - - debug("[I2C] i2mod=%08x i2brg=%08x\n", - i2c->i2c_i2mod, - i2c->i2c_i2brg); - - return 1; -} - -void i2c_init(int speed, int slaveaddr) -{ - volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; - volatile cpm8xx_t *cp = (cpm8xx_t *)&immap->im_cpm; - volatile i2c8xx_t *i2c = (i2c8xx_t *)&immap->im_i2c; - volatile iic_t *iip = (iic_t *)&cp->cp_dparam[PROFF_IIC]; - ulong rbase, tbase; - volatile I2C_BD *rxbd, *txbd; - uint dpaddr; - -#ifdef CONFIG_SYS_I2C_INIT_BOARD - /* call board specific i2c bus reset routine before accessing the */ - /* environment, which might be in a chip on that bus. For details */ - /* about this problem see doc/I2C_Edge_Conditions. */ - i2c_init_board(); -#endif - -#ifdef CONFIG_SYS_I2C_UCODE_PATCH - iip = (iic_t *)&cp->cp_dpmem[iip->iic_rpbase]; -#else - /* Disable relocation */ - iip->iic_rpbase = 0; -#endif - - dpaddr = CPM_I2C_BASE; - - /* - * initialise data in dual port ram: - * - * dpaddr->rbase -> rx BD (NUM_RX_BDS * sizeof(I2C_BD) bytes) - * tbase -> tx BD (NUM_TX_BDS * sizeof(I2C_BD) bytes) - * tx buffer (MAX_TX_SPACE bytes) - */ - - rbase = dpaddr; - tbase = rbase + NUM_RX_BDS * sizeof(I2C_BD); - - /* Initialize Port B I2C pins. */ - cp->cp_pbpar |= 0x00000030; - cp->cp_pbdir |= 0x00000030; - cp->cp_pbodr |= 0x00000030; - - /* Disable interrupts */ - i2c->i2c_i2mod = 0x00; - i2c->i2c_i2cmr = 0x00; - i2c->i2c_i2cer = 0xff; - i2c->i2c_i2add = slaveaddr; - - /* - * Set the I2C BRG Clock division factor from desired i2c rate - * and current CPU rate (we assume sccr dfbgr field is 0; - * divide BRGCLK by 1) - */ - debug("[I2C] Setting rate...\n"); - i2c_setrate(gd->cpu_clk, CONFIG_SYS_I2C_SPEED); - - /* Set I2C controller in master mode */ - i2c->i2c_i2com = 0x01; - - /* Set SDMA bus arbitration level to 5 (SDCR) */ - immap->im_siu_conf.sc_sdcr = 0x0001; - - /* Initialize Tx/Rx parameters */ - iip->iic_rbase = rbase; - iip->iic_tbase = tbase; - rxbd = (I2C_BD *) ((unsigned char *) &cp->cp_dpmem[iip->iic_rbase]); - txbd = (I2C_BD *) ((unsigned char *) &cp->cp_dpmem[iip->iic_tbase]); - - debug("[I2C] rbase = %04x\n", iip->iic_rbase); - debug("[I2C] tbase = %04x\n", iip->iic_tbase); - debug("[I2C] rxbd = %08x\n", (int)rxbd); - debug("[I2C] txbd = %08x\n", (int)txbd); - - /* Set big endian byte order */ - iip->iic_tfcr = 0x10; - iip->iic_rfcr = 0x10; - - /* Set maximum receive size. */ - iip->iic_mrblr = I2C_RXTX_LEN; - -#ifdef CONFIG_SYS_I2C_UCODE_PATCH - /* - * Initialize required parameters if using microcode patch. - */ - iip->iic_rbptr = iip->iic_rbase; - iip->iic_tbptr = iip->iic_tbase; - iip->iic_rstate = 0; - iip->iic_tstate = 0; -#else - cp->cp_cpcr = mk_cr_cmd(CPM_CR_CH_I2C, CPM_CR_INIT_TRX) | CPM_CR_FLG; - do { - __asm__ __volatile__("eieio"); - } while (cp->cp_cpcr & CPM_CR_FLG); -#endif - - /* Clear events and interrupts */ - i2c->i2c_i2cer = 0xff; - i2c->i2c_i2cmr = 0x00; -} - -static void i2c_newio(i2c_state_t *state) -{ - volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR; - volatile cpm8xx_t *cp = (cpm8xx_t *)&immap->im_cpm; - volatile iic_t *iip = (iic_t *)&cp->cp_dparam[PROFF_IIC]; - - debug("[I2C] i2c_newio\n"); - -#ifdef CONFIG_SYS_I2C_UCODE_PATCH - iip = (iic_t *)&cp->cp_dpmem[iip->iic_rpbase]; -#endif - state->rx_idx = 0; - state->tx_idx = 0; - state->rxbd = (void *)&cp->cp_dpmem[iip->iic_rbase]; - state->txbd = (void *)&cp->cp_dpmem[iip->iic_tbase]; - state->tx_space = MAX_TX_SPACE; - state->tx_buf = (uchar *)state->txbd + NUM_TX_BDS * sizeof(I2C_BD); - state->err_cb = NULL; - - debug("[I2C] rxbd = %08x\n", (int)state->rxbd); - debug("[I2C] txbd = %08x\n", (int)state->txbd); - debug("[I2C] tx_buf = %08x\n", (int)state->tx_buf); - - /* clear the buffer memory */ - memset((char *)state->tx_buf, 0, MAX_TX_SPACE); -} - -static int -i2c_send(i2c_state_t *state, - unsigned char address, - unsigned char secondary_address, - unsigned int flags, unsigned short size, unsigned char *dataout) -{ - volatile I2C_BD *txbd; - int i, j; - - debug("[I2C] i2c_send add=%02d sec=%02d flag=%02d size=%d\n", - address, secondary_address, flags, size); - - /* trying to send message larger than BD */ - if (size > I2C_RXTX_LEN) - return I2CERR_MSG_TOO_LONG; - - /* no more free bds */ - if (state->tx_idx >= NUM_TX_BDS || state->tx_space < (2 + size)) - return I2CERR_NO_BUFFERS; - - txbd = (I2C_BD *) state->txbd; - txbd->addr = state->tx_buf; - - debug("[I2C] txbd = %08x\n", (int)txbd); - - if (flags & I2CF_START_COND) { - debug("[I2C] Formatting addresses...\n"); - if (flags & I2CF_ENABLE_SECONDARY) { - /* Length of msg + dest addr */ - txbd->length = size + 2; - - txbd->addr[0] = address << 1; - txbd->addr[1] = secondary_address; - i = 2; - } else { - /* Length of msg + dest addr */ - txbd->length = size + 1; - /* Write dest addr to BD */ - txbd->addr[0] = address << 1; - i = 1; - } - } else { - txbd->length = size; /* Length of message */ - i = 0; - } - - /* set up txbd */ - txbd->status = BD_SC_READY; - if (flags & I2CF_START_COND) - txbd->status |= BD_I2C_TX_START; - if (flags & I2CF_STOP_COND) - txbd->status |= BD_SC_LAST | BD_SC_WRAP; - - /* Copy data to send into buffer */ - debug("[I2C] copy data...\n"); - for(j = 0; j < size; i++, j++) - txbd->addr[i] = dataout[j]; - - debug("[I2C] txbd: length=0x%04x status=0x%04x addr[0]=0x%02x addr[1]=0x%02x\n", - txbd->length, - txbd->status, - txbd->addr[0], - txbd->addr[1]); - - /* advance state */ - state->tx_buf += txbd->length; - state->tx_space -= txbd->length; - state->tx_idx++; - state->txbd = (void *) (txbd + 1); - - return 0; -} - -static int -i2c_receive(i2c_state_t *state, - unsigned char address, - unsigned char secondary_address, - unsigned int flags, - unsigned short size_to_expect, unsigned char *datain) -{ - volatile I2C_BD *rxbd, *txbd; - - debug("[I2C] i2c_receive %02d %02d %02d\n", - address, secondary_address, flags); - - /* Expected to receive too much */ - if (size_to_expect > I2C_RXTX_LEN) - return I2CERR_MSG_TOO_LONG; - - /* no more free bds */ - if (state->tx_idx >= NUM_TX_BDS || state->rx_idx >= NUM_RX_BDS - || state->tx_space < 2) - return I2CERR_NO_BUFFERS; - - rxbd = (I2C_BD *) state->rxbd; - txbd = (I2C_BD *) state->txbd; - - debug("[I2C] rxbd = %08x\n", (int)rxbd); - debug("[I2C] txbd = %08x\n", (int)txbd); - - txbd->addr = state->tx_buf; - - /* set up TXBD for destination address */ - if (flags & I2CF_ENABLE_SECONDARY) { - txbd->length = 2; - txbd->addr[0] = address << 1; /* Write data */ - txbd->addr[1] = secondary_address; /* Internal address */ - txbd->status = BD_SC_READY; - } else { - txbd->length = 1 + size_to_expect; - txbd->addr[0] = (address << 1) | 0x01; - txbd->status = BD_SC_READY; - memset(&txbd->addr[1], 0, txbd->length); - } - - /* set up rxbd for reception */ - rxbd->status = BD_SC_EMPTY; - rxbd->length = size_to_expect; - rxbd->addr = datain; - - txbd->status |= BD_I2C_TX_START; - if (flags & I2CF_STOP_COND) { - txbd->status |= BD_SC_LAST | BD_SC_WRAP; - rxbd->status |= BD_SC_WRAP; - } - - debug("[I2C] txbd: length=0x%04x status=0x%04x addr[0]=0x%02x addr[1]=0x%02x\n", - txbd->length, - txbd->status, - txbd->addr[0], - txbd->addr[1]); - debug("[I2C] rxbd: length=0x%04x status=0x%04x addr[0]=0x%02x addr[1]=0x%02x\n", - rxbd->length, - rxbd->status, - rxbd->addr[0], - rxbd->addr[1]); - - /* advance state */ - state->tx_buf += txbd->length; - state->tx_space -= txbd->length; - state->tx_idx++; - state->txbd = (void *) (txbd + 1); - state->rx_idx++; - state->rxbd = (void *) (rxbd + 1); - - return 0; -} - - -static int i2c_doio(i2c_state_t *state) -{ - volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR; - volatile cpm8xx_t *cp = (cpm8xx_t *)&immap->im_cpm; - volatile i2c8xx_t *i2c = (i2c8xx_t *)&immap->im_i2c; - volatile iic_t *iip = (iic_t *)&cp->cp_dparam[PROFF_IIC]; - volatile I2C_BD *txbd, *rxbd; - volatile int j = 0; - - debug("[I2C] i2c_doio\n"); - -#ifdef CONFIG_SYS_I2C_UCODE_PATCH - iip = (iic_t *)&cp->cp_dpmem[iip->iic_rpbase]; -#endif - - if (state->tx_idx <= 0 && state->rx_idx <= 0) { - debug("[I2C] No I/O is queued\n"); - return I2CERR_QUEUE_EMPTY; - } - - iip->iic_rbptr = iip->iic_rbase; - iip->iic_tbptr = iip->iic_tbase; - - /* Enable I2C */ - debug("[I2C] Enabling I2C...\n"); - i2c->i2c_i2mod |= 0x01; - - /* Begin transmission */ - i2c->i2c_i2com |= 0x80; - - /* Loop until transmit & receive completed */ - - if (state->tx_idx > 0) { - txbd = ((I2C_BD*)state->txbd) - 1; - - debug("[I2C] Transmitting...(txbd=0x%08lx)\n", - (ulong)txbd); - - while ((txbd->status & BD_SC_READY) && (j++ < TOUT_LOOP)) { - if (ctrlc()) - return (-1); - - __asm__ __volatile__("eieio"); - } - } - - if ((state->rx_idx > 0) && (j < TOUT_LOOP)) { - rxbd = ((I2C_BD*)state->rxbd) - 1; - - debug("[I2C] Receiving...(rxbd=0x%08lx)\n", - (ulong)rxbd); - - while ((rxbd->status & BD_SC_EMPTY) && (j++ < TOUT_LOOP)) { - if (ctrlc()) - return (-1); - - __asm__ __volatile__("eieio"); - } - } - - /* Turn off I2C */ - i2c->i2c_i2mod &= ~0x01; - - if (state->err_cb != NULL) { - int n, i, b; - - /* - * if we have an error callback function, look at the - * error bits in the bd status and pass them back - */ - - if ((n = state->tx_idx) > 0) { - for (i = 0; i < n; i++) { - txbd = ((I2C_BD *) state->txbd) - (n - i); - if ((b = txbd->status & BD_I2C_TX_ERR) != 0) - (*state->err_cb) (I2CECB_TX_ERR | b, - i); - } - } - - if ((n = state->rx_idx) > 0) { - for (i = 0; i < n; i++) { - rxbd = ((I2C_BD *) state->rxbd) - (n - i); - if ((b = rxbd->status & BD_I2C_RX_ERR) != 0) - (*state->err_cb) (I2CECB_RX_ERR | b, - i); - } - } - - if (j >= TOUT_LOOP) - (*state->err_cb) (I2CECB_TIMEOUT, 0); - } - - return (j >= TOUT_LOOP) ? I2CERR_TIMEOUT : 0; -} - -static int had_tx_nak; - -static void i2c_test_callback(int flags, int xnum) -{ - if ((flags & I2CECB_TX_ERR) && (flags & I2CECB_TX_NAK)) - had_tx_nak = 1; -} - -int i2c_probe(uchar chip) -{ - i2c_state_t state; - int rc; - uchar buf[1]; - - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); - - i2c_newio(&state); - - state.err_cb = i2c_test_callback; - had_tx_nak = 0; - - rc = i2c_receive(&state, chip, 0, I2CF_START_COND | I2CF_STOP_COND, 1, - buf); - - if (rc != 0) - return (rc); - - rc = i2c_doio(&state); - - if ((rc != 0) && (rc != I2CERR_TIMEOUT)) - return (rc); - - return (had_tx_nak); -} - -int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len) -{ - i2c_state_t state; - uchar xaddr[4]; - int rc; - - xaddr[0] = (addr >> 24) & 0xFF; - xaddr[1] = (addr >> 16) & 0xFF; - xaddr[2] = (addr >> 8) & 0xFF; - xaddr[3] = addr & 0xFF; - -#ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW - /* - * EEPROM chips that implement "address overflow" are ones like - * Catalyst 24WC04/08/16 which has 9/10/11 bits of address and the - * extra bits end up in the "chip address" bit slots. This makes - * a 24WC08 (1Kbyte) chip look like four 256 byte chips. - * - * Note that we consider the length of the address field to still - * be one byte because the extra address bits are hidden in the - * chip address. - */ - chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW); -#endif - - i2c_newio(&state); - - rc = i2c_send(&state, chip, 0, I2CF_START_COND, alen, - &xaddr[4 - alen]); - if (rc != 0) { - printf("i2c_read: i2c_send failed (%d)\n", rc); - return 1; - } - - rc = i2c_receive(&state, chip, 0, I2CF_STOP_COND, len, buffer); - if (rc != 0) { - printf("i2c_read: i2c_receive failed (%d)\n", rc); - return 1; - } - - rc = i2c_doio(&state); - if (rc != 0) { - printf("i2c_read: i2c_doio failed (%d)\n", rc); - return 1; - } - return 0; -} - -int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len) -{ - i2c_state_t state; - uchar xaddr[4]; - int rc; - - xaddr[0] = (addr >> 24) & 0xFF; - xaddr[1] = (addr >> 16) & 0xFF; - xaddr[2] = (addr >> 8) & 0xFF; - xaddr[3] = addr & 0xFF; - -#ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW - /* - * EEPROM chips that implement "address overflow" are ones like - * Catalyst 24WC04/08/16 which has 9/10/11 bits of address and the - * extra bits end up in the "chip address" bit slots. This makes - * a 24WC08 (1Kbyte) chip look like four 256 byte chips. - * - * Note that we consider the length of the address field to still - * be one byte because the extra address bits are hidden in the - * chip address. - */ - chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW); -#endif - - i2c_newio(&state); - - rc = i2c_send(&state, chip, 0, I2CF_START_COND, alen, - &xaddr[4 - alen]); - if (rc != 0) { - printf("i2c_write: first i2c_send failed (%d)\n", rc); - return 1; - } - - rc = i2c_send(&state, 0, 0, I2CF_STOP_COND, len, buffer); - if (rc != 0) { - printf("i2c_write: second i2c_send failed (%d)\n", rc); - return 1; - } - - rc = i2c_doio(&state); - if (rc != 0) { - printf("i2c_write: i2c_doio failed (%d)\n", rc); - return 1; - } - return 0; -} - -#endif /* CONFIG_HARD_I2C */ diff --git a/board/alphaproject/ap_sh4a_4a/ap_sh4a_4a.c b/board/alphaproject/ap_sh4a_4a/ap_sh4a_4a.c index 31418a1f96..9205c22e0b 100644 --- a/board/alphaproject/ap_sh4a_4a/ap_sh4a_4a.c +++ b/board/alphaproject/ap_sh4a_4a/ap_sh4a_4a.c @@ -156,17 +156,7 @@ int board_init(void) int board_late_init(void) { - u8 mac[6]; - - /* Read Mac Address and set*/ - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); - i2c_set_bus_num(CONFIG_SYS_I2C_MODULE); - - /* Read MAC address */ - i2c_read(0x50, 0x0, 0, mac, 6); - - if (is_valid_ethaddr(mac)) - eth_setenv_enetaddr("ethaddr", mac); + printf("Cannot use I2C to get MAC address\n"); return 0; } diff --git a/board/atmel/at91sam9x5ek/at91sam9x5ek.c b/board/atmel/at91sam9x5ek/at91sam9x5ek.c index c661c77f83..81c2aad1a5 100644 --- a/board/atmel/at91sam9x5ek/at91sam9x5ek.c +++ b/board/atmel/at91sam9x5ek/at91sam9x5ek.c @@ -212,7 +212,7 @@ int board_init(void) at91sam9x5ek_nand_hw_init(); #endif -#if defined(CONFIG_USB_OHCI_NEW) || defined(CONFIG_USB_EHCI) +#if defined(CONFIG_USB_OHCI_NEW) || defined(CONFIG_USB_EHCI_HCD) at91_uhp_hw_init(); #endif #ifdef CONFIG_LCD diff --git a/board/cm5200/cm5200.c b/board/cm5200/cm5200.c index 7b862355c8..0c647bbd3d 100644 --- a/board/cm5200/cm5200.c +++ b/board/cm5200/cm5200.c @@ -161,14 +161,7 @@ int dram_init(void) */ static void read_hw_id(hw_id_t hw_id) { - int i; - for (i = 0; i < HW_ID_ELEM_COUNT; ++i) - if (i2c_read(CONFIG_SYS_I2C_EEPROM, - hw_id_format[i].offset, - 2, - (uchar *)&hw_id[i][0], - hw_id_format[i].length) != 0) - printf("ERROR: can't read HW ID from EEPROM\n"); + printf("ERROR: can't read HW ID from EEPROM\n"); } @@ -221,7 +214,7 @@ static void compose_module_name(hw_id_t hw_id, char *buf) strcat(buf, tmp); } - +#if defined(CONFIG_SYS_I2C_SOFT) /* * Compose string with hostname. * buf is assumed to have enough space, and be null-terminated. @@ -237,7 +230,7 @@ static void compose_hostname(hw_id_t hw_id, char *buf) *p = tolower(*p); } - +#endif #ifdef CONFIG_OF_BOARD_SETUP /* @@ -270,15 +263,6 @@ int checkboard(void) hw_id_t hw_id_tmp; char module_name_tmp[MODULE_NAME_MAXLEN] = ""; - /* - * We need I2C to access HW ID data from EEPROM, so we call i2c_init() - * here despite the fact that it will be called again later on. We - * also use a little trick to silence I2C-related output. - */ - gd->flags |= GD_FLG_SILENT; - i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); - gd->flags &= ~GD_FLG_SILENT; - read_hw_id(hw_id_tmp); identify_module(hw_id_tmp); /* this sets gd->board_type */ compose_module_name(hw_id_tmp, module_name_tmp); @@ -311,7 +295,7 @@ int board_early_init_r(void) #ifdef CONFIG_MISC_INIT_R int misc_init_r(void) { -#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT) +#if defined(CONFIG_SYS_I2C_SOFT) uchar buf[6]; char str[18]; char hostname[MODULE_NAME_MAXLEN]; @@ -334,16 +318,16 @@ int misc_init_r(void) " device at address %02X:%04X\n", CONFIG_SYS_I2C_EEPROM, CONFIG_MAC_OFFSET); } -#endif /* defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT) */ - if (!getenv("ethaddr")) - printf(LOG_PREFIX "MAC address not set, networking is not " - "operational\n"); - - /* set the hostname appropriate to the module we're running on */ hostname[0] = 0x00; + /* set the hostname appropriate to the module we're running on */ compose_hostname(hw_id, hostname); setenv("hostname", hostname); +#endif /* defined(CONFIG_SYS_I2C_SOFT) */ + if (!getenv("ethaddr")) + printf(LOG_PREFIX "MAC address not set, networking is not " + "operational\n"); + return 0; } #endif /* CONFIG_MISC_INIT_R */ diff --git a/board/cm5200/cmd_cm5200.c b/board/cm5200/cmd_cm5200.c index 9c40ad7b2a..60097dc8c7 100644 --- a/board/cm5200/cmd_cm5200.c +++ b/board/cm5200/cmd_cm5200.c @@ -13,34 +13,6 @@ #ifdef CONFIG_CMD_BSP -static int do_i2c_test(char * const argv[]) -{ - unsigned char temp, temp1; - - printf("Starting I2C Test\n" - "Please set Jumper:\nI2C SDA 2-3\nI2C SCL 2-3\n\n" - "Please press any key to start\n\n"); - getc(); - - temp = 0xf0; /* set io 0-4 as output */ - i2c_write(CONFIG_SYS_I2C_IO, 3, 1, (uchar *)&temp, 1); - - printf("Press I2C4-7. LED I2C0-3 should have the same state\n\n" - "Press any key to stop\n\n"); - - while (!tstc()) { - i2c_read(CONFIG_SYS_I2C_IO, 0, 1, (uchar *)&temp, 1); - temp1 = (temp >> 4) & 0x03; - temp1 |= (temp >> 3) & 0x08; /* S302 -> LED303 */ - temp1 |= (temp >> 5) & 0x04; /* S303 -> LED302 */ - temp = temp1; - i2c_write(CONFIG_SYS_I2C_IO, 1, 1, (uchar *)&temp, 1); - } - getc(); - - return 0; -} - static int do_usb_test(char * const argv[]) { int i; @@ -387,9 +359,7 @@ static int cmd_fkt(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) switch (argc) { case 2: - if (strncmp(argv[1], "i2c", 3) == 0) - rcode = do_i2c_test(argv); - else if (strncmp(argv[1], "led", 3) == 0) + if (strncmp(argv[1], "led", 3) == 0) rcode = do_led_test(argv); else if (strncmp(argv[1], "usb", 3) == 0) rcode = do_usb_test(argv); diff --git a/board/compulab/cm_t54/cm_t54.c b/board/compulab/cm_t54/cm_t54.c index 456ff247e9..6437718415 100644 --- a/board/compulab/cm_t54/cm_t54.c +++ b/board/compulab/cm_t54/cm_t54.c @@ -181,7 +181,7 @@ int board_eth_init(bd_t *bis) } #endif -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD static struct omap_usbhs_board_data usbhs_bdata = { .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED, .port_mode[1] = OMAP_EHCI_PORT_MODE_HSIC, diff --git a/board/davedenx/aria/aria.c b/board/davedenx/aria/aria.c index e3441cad4e..e389819e9d 100644 --- a/board/davedenx/aria/aria.c +++ b/board/davedenx/aria/aria.c @@ -29,9 +29,6 @@ int misc_init_r(void) { u32 tmp; - /* we use I2C-2 for on-board eeprom */ - i2c_set_bus_num(2); - tmp = in_be32((u32*)CONFIG_SYS_ARIA_FPGA_BASE); printf("FPGA: %u-%u.%u.%u\n", (tmp & 0xFF000000) >> 24, diff --git a/board/esd/mecp5123/mecp5123.c b/board/esd/mecp5123/mecp5123.c index 66dc407bae..78a6b66110 100644 --- a/board/esd/mecp5123/mecp5123.c +++ b/board/esd/mecp5123/mecp5123.c @@ -18,17 +18,7 @@ DECLARE_GLOBAL_DATA_PTR; int eeprom_write_enable(unsigned dev_addr, int state) { - volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR; - - if (dev_addr != CONFIG_SYS_I2C_EEPROM_ADDR) - return -1; - - if (state == 0) - setbits_be32(&im->gpio.gpdat, 0x00100000); - else - clrbits_be32(&im->gpio.gpdat, 0x00100000); - - return 0; + return -ENOSYS; } int board_early_init_f(void) diff --git a/board/freescale/m52277evb/README b/board/freescale/m52277evb/README index 92a83849ac..89e033e1c5 100644 --- a/board/freescale/m52277evb/README +++ b/board/freescale/m52277evb/README @@ -83,7 +83,6 @@ CONFIG_MCFTMR -- define to use DMA timer CONFIG_MCFPIT -- define to use PIT timer CONFIG_SYS_I2C_FSL -- define to use FSL common I2C driver -CONFIG_HARD_I2C -- define for I2C hardware support CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged CONFIG_SYS_I2C_SPEED -- define for I2C speed CONFIG_SYS_I2C_SLAVE -- define for I2C slave address diff --git a/board/freescale/m53017evb/README b/board/freescale/m53017evb/README index 224e79c46a..2fca12c417 100644 --- a/board/freescale/m53017evb/README +++ b/board/freescale/m53017evb/README @@ -91,7 +91,6 @@ CONFIG_MCFTMR -- define to use DMA timer CONFIG_MCFPIT -- define to use PIT timer CONFIG_SYS_I2C_FSL -- define to use FSL common I2C driver -CONFIG_HARD_I2C -- define for I2C hardware support CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged CONFIG_SYS_I2C_SPEED -- define for I2C speed CONFIG_SYS_I2C_SLAVE -- define for I2C slave address diff --git a/board/freescale/m5373evb/README b/board/freescale/m5373evb/README index 582e0c3d9e..757f0abdd7 100644 --- a/board/freescale/m5373evb/README +++ b/board/freescale/m5373evb/README @@ -90,7 +90,6 @@ CONFIG_MCFTMR -- define to use DMA timer CONFIG_MCFPIT -- define to use PIT timer CONFIG_SYS_I2C_FSL -- define to use FSL common I2C driver -CONFIG_HARD_I2C -- define for I2C hardware support CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged CONFIG_SYS_I2C_SPEED -- define for I2C speed CONFIG_SYS_I2C_SLAVE -- define for I2C slave address diff --git a/board/freescale/m54455evb/README b/board/freescale/m54455evb/README index c563ad99a7..4a8719333a 100644 --- a/board/freescale/m54455evb/README +++ b/board/freescale/m54455evb/README @@ -113,7 +113,6 @@ CONFIG_MCFTMR -- define to use DMA timer CONFIG_MCFPIT -- define to use PIT timer CONFIG_SYS_FSL_I2C -- define to use FSL common I2C driver -CONFIG_HARD_I2C -- define for I2C hardware support CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged CONFIG_SYS_I2C_SPEED -- define for I2C speed CONFIG_SYS_I2C_SLAVE -- define for I2C slave address diff --git a/board/freescale/m547xevb/README b/board/freescale/m547xevb/README index 30c5dedafe..ce7b27b8b2 100644 --- a/board/freescale/m547xevb/README +++ b/board/freescale/m547xevb/README @@ -98,7 +98,6 @@ CONFIG_DOS_PARTITION -- enable DOS read/write CONFIG_SLTTMR -- define to use SLT timer CONFIG_SYS_I2C_FSL -- define to use FSL common I2C driver -CONFIG_HARD_I2C -- define for I2C hardware support CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged CONFIG_SYS_I2C_SPEED -- define for I2C speed CONFIG_SYS_I2C_SLAVE -- define for I2C slave address diff --git a/board/freescale/mpc5121ads/mpc5121ads.c b/board/freescale/mpc5121ads/mpc5121ads.c index f87579f193..d729056fd0 100644 --- a/board/freescale/mpc5121ads/mpc5121ads.c +++ b/board/freescale/mpc5121ads/mpc5121ads.c @@ -174,27 +174,6 @@ int dram_init(void) int misc_init_r(void) { - u8 tmp_val; - - /* Using this for DIU init before the driver in linux takes over - * Enable the TFP410 Encoder (I2C address 0x38) - */ - - i2c_set_bus_num(2); - tmp_val = 0xBF; - i2c_write(0x38, 0x08, 1, &tmp_val, sizeof(tmp_val)); - /* Verify if enabled */ - tmp_val = 0; - i2c_read(0x38, 0x08, 1, &tmp_val, sizeof(tmp_val)); - debug("DVI Encoder Read: 0x%02x\n", tmp_val); - - tmp_val = 0x10; - i2c_write(0x38, 0x0A, 1, &tmp_val, sizeof(tmp_val)); - /* Verify if enabled */ - tmp_val = 0; - i2c_read(0x38, 0x0A, 1, &tmp_val, sizeof(tmp_val)); - debug("DVI Encoder Read: 0x%02x\n", tmp_val); - return 0; } diff --git a/board/gumstix/duovero/duovero.c b/board/gumstix/duovero/duovero.c index ea32f4a333..fefcde87ae 100644 --- a/board/gumstix/duovero/duovero.c +++ b/board/gumstix/duovero/duovero.c @@ -24,7 +24,7 @@ static void setup_net_chip(void); #endif -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD #include <usb.h> #include <asm/arch/ehci.h> #include <asm/ehci-omap.h> @@ -206,7 +206,7 @@ int board_eth_init(bd_t *bis) return rc; } -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD static struct omap_usbhs_board_data usbhs_bdata = { .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, diff --git a/board/htkw/mcx/mcx.c b/board/htkw/mcx/mcx.c index 12358f1b61..1deb2bdd8b 100644 --- a/board/htkw/mcx/mcx.c +++ b/board/htkw/mcx/mcx.c @@ -19,7 +19,7 @@ #include <asm/arch/clock.h> #include <errno.h> #include <i2c.h> -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD #include <usb.h> #include <asm/ehci-omap.h> #endif @@ -33,7 +33,7 @@ DECLARE_GLOBAL_DATA_PTR; /* Address of the framebuffer in RAM. */ #define FB_START_ADDRESS 0x88000000 -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD static struct omap_usbhs_board_data usbhs_bdata = { .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, .port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED, diff --git a/board/ifm/ac14xx/ac14xx.c b/board/ifm/ac14xx/ac14xx.c index 348613736d..cd79e804a0 100644 --- a/board/ifm/ac14xx/ac14xx.c +++ b/board/ifm/ac14xx/ac14xx.c @@ -17,7 +17,6 @@ #include <i2c.h> #endif -static int eeprom_diag; static int mac_diag; static int gpio_diag; @@ -136,7 +135,6 @@ struct __attribute__ ((__packed__)) eeprom_layout { #define HW_COMP_MAINCPU 2 static struct eeprom_layout eeprom_content; -static int eeprom_was_read; /* has_been_read */ static int eeprom_is_valid; static int eeprom_version; @@ -153,53 +151,7 @@ static int eeprom_version; static int read_eeprom(void) { - int eeprom_datalen; - int ret; - - if (eeprom_was_read) - return 0; - - eeprom_is_valid = 0; - ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, - CONFIG_SYS_I2C_EEPROM_ADDR_LEN, - (uchar *)&eeprom_content, sizeof(eeprom_content)); - if (eeprom_diag) { - printf("DIAG: %s() read rc[%d], size[%d]\n", - __func__, ret, sizeof(eeprom_content)); - } - - if (ret != 0) - return -1; - - eeprom_was_read = 1; - - /* - * check validity of EEPROM content - * (check version, length, optionally checksum) - */ - eeprom_is_valid = 1; - eeprom_datalen = get_eeprom_field_int(eeprom_content.len); - eeprom_version = get_eeprom_field_int(eeprom_content.version); - - if (eeprom_diag) { - printf("DIAG: %s() magic[%c%c%c] len[%d] ver[%d] type[%d]\n", - __func__, eeprom_content.magic[0], - eeprom_content.magic[1], eeprom_content.magic[2], - eeprom_datalen, eeprom_version, eeprom_content.type); - } - if (strncmp(eeprom_content.magic, "ifm", strlen("ifm")) != 0) - eeprom_is_valid = 0; - if (eeprom_datalen < sizeof(struct eeprom_layout) - 5) - eeprom_is_valid = 0; - if ((eeprom_version != 1) && (eeprom_version != 2)) - eeprom_is_valid = 0; - if (eeprom_content.type != HW_COMP_MAINCPU) - eeprom_is_valid = 0; - - if (eeprom_diag) - printf("DIAG: %s() valid[%d]\n", __func__, eeprom_is_valid); - - return ret; + return -ENOSYS; } int mac_read_from_eeprom(void) @@ -324,9 +276,6 @@ int misc_init_r(void) char *s; int want_recovery; - /* we use bus I2C-0 for the on-board eeprom */ - i2c_set_bus_num(0); - /* setup GPIO directions and initial values */ gpio_configure(); diff --git a/board/keymile/km82xx/km82xx.c b/board/keymile/km82xx/km82xx.c index 51b4571d40..f5a98b33e7 100644 --- a/board/keymile/km82xx/km82xx.c +++ b/board/keymile/km82xx/km82xx.c @@ -153,13 +153,8 @@ const iop_conf_t iop_conf_tab[4][32] = { { 0, 0, 0, 0, 0, 0 }, /* PD18 */ { 0, 0, 0, 0, 0, 0 }, /* PD17 */ { 0, 0, 0, 0, 0, 0 }, /* PD16 */ -#if defined(CONFIG_HARD_I2C) - { 1, 1, 1, 0, 1, 0 }, /* PD15 I2C SDA */ - { 1, 1, 1, 0, 1, 0 }, /* PD14 I2C SCL */ -#else { 1, 0, 0, 0, 1, 1 }, /* PD15 */ { 1, 0, 0, 1, 1, 1 }, /* PD14 */ -#endif { 0, 0, 0, 0, 0, 0 }, /* PD13 */ { 0, 0, 0, 0, 0, 0 }, /* PD12 */ { 0, 0, 0, 0, 0, 0 }, /* PD11 */ diff --git a/board/keymile/km_arm/km_arm.c b/board/keymile/km_arm/km_arm.c index 079509c979..85785ffc02 100644 --- a/board/keymile/km_arm/km_arm.c +++ b/board/keymile/km_arm/km_arm.c @@ -76,10 +76,6 @@ static const u32 kwmpp_config[] = { MPP8_GPIO, /* SDA */ MPP9_GPIO, /* SCL */ #endif -#if defined(CONFIG_HARD_I2C) - MPP8_TW_SDA, - MPP9_TW_SCK, -#endif MPP10_UART0_TXD, MPP11_UART0_RXD, MPP12_GPO, /* Reserved */ diff --git a/board/logicpd/omap3som/Kconfig b/board/logicpd/omap3som/Kconfig index 03d272a806..68d40dcd62 100644 --- a/board/logicpd/omap3som/Kconfig +++ b/board/logicpd/omap3som/Kconfig @@ -9,4 +9,6 @@ config SYS_VENDOR config SYS_CONFIG_NAME default "omap3_logic" +source "board/ti/common/Kconfig" + endif diff --git a/board/overo/overo.c b/board/overo/overo.c index f1a3d73062..adf33cfd37 100644 --- a/board/overo/overo.c +++ b/board/overo/overo.c @@ -27,7 +27,7 @@ #include <asm/mach-types.h> #include "overo.h" -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD #include <usb.h> #include <asm/ehci-omap.h> #endif @@ -393,7 +393,7 @@ void board_mmc_power_init(void) } #endif -#if defined(CONFIG_USB_EHCI) +#if defined(CONFIG_USB_EHCI_HCD) static struct omap_usbhs_board_data usbhs_bdata = { .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED, .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, @@ -420,4 +420,4 @@ int ehci_hcd_stop(void) return omap_ehci_hcd_stop(); } -#endif /* CONFIG_USB_EHCI */ +#endif /* CONFIG_USB_EHCI_HCD */ diff --git a/board/pdm360ng/pdm360ng.c b/board/pdm360ng/pdm360ng.c index 9db31d3312..371bcd9e6b 100644 --- a/board/pdm360ng/pdm360ng.c +++ b/board/pdm360ng/pdm360ng.c @@ -169,36 +169,6 @@ int misc_init_r(void) clrsetbits_be32(&im->gpio.gpdat, 0x01000000, 0x00040000); #endif -#if defined(CONFIG_HARD_I2C) - if (!getenv("ethaddr")) { - uchar buf[6]; - uchar ifm_oui[3] = { 0, 2, 1, }; - int ret; - - /* I2C-0 for on-board eeprom */ - i2c_set_bus_num(CONFIG_SYS_I2C_EEPROM_BUS_NUM); - - /* Read ethaddr from EEPROM */ - ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, - CONFIG_SYS_I2C_EEPROM_MAC_OFFSET, 1, buf, 6); - if (ret != 0) { - printf("Error: Unable to read MAC from I2C" - " EEPROM at address %02X:%02X\n", - CONFIG_SYS_I2C_EEPROM_ADDR, - CONFIG_SYS_I2C_EEPROM_MAC_OFFSET); - return 1; - } - - /* Owned by IFM ? */ - if (memcmp(buf, ifm_oui, sizeof(ifm_oui))) { - printf("Illegal MAC address in EEPROM: %pM\n", buf); - return 1; - } - - eth_setenv_enetaddr("ethaddr", buf); - } -#endif /* defined(CONFIG_HARD_I2C) */ - return 0; } diff --git a/board/quipos/cairo/cairo.c b/board/quipos/cairo/cairo.c index 5fce45e879..6cf54095f5 100644 --- a/board/quipos/cairo/cairo.c +++ b/board/quipos/cairo/cairo.c @@ -26,18 +26,6 @@ DECLARE_GLOBAL_DATA_PTR; /* - * MUSB port on OMAP3EVM Rev >= E requires extvbus programming. - */ -u8 omap3_evm_need_extvbus(void) -{ - u8 retval = 0; - - /* TODO: verify if cairo handheld platform needs extvbus programming */ - - return retval; -} - -/* * Routine: board_init * Description: Early hardware init. */ diff --git a/board/renesas/r0p7734/r0p7734.c b/board/renesas/r0p7734/r0p7734.c index 360e0a1a6f..d0b4537513 100644 --- a/board/renesas/r0p7734/r0p7734.c +++ b/board/renesas/r0p7734/r0p7734.c @@ -44,17 +44,7 @@ int board_init(void) int board_late_init(void) { - u8 mac[6]; - - /* Read Mac Address and set*/ - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); - i2c_set_bus_num(CONFIG_SYS_I2C_MODULE); - - /* Read MAC address */ - i2c_read(0x50, 0x10, 0, mac, 6); - - if (is_valid_ethaddr(mac)) - eth_setenv_enetaddr("ethaddr", mac); + printf("Cannot get MAC address from I2C\n"); return 0; } diff --git a/board/technexion/tao3530/tao3530.c b/board/technexion/tao3530/tao3530.c index 21944c73e2..c5966e3571 100644 --- a/board/technexion/tao3530/tao3530.c +++ b/board/technexion/tao3530/tao3530.c @@ -195,7 +195,7 @@ void board_mmc_power_init(void) } #endif -#if defined(CONFIG_USB_EHCI) && !defined(CONFIG_SPL_BUILD) +#if defined(CONFIG_USB_EHCI_HCD) && !defined(CONFIG_SPL_BUILD) /* Call usb_stop() before starting the kernel */ void show_boot_progress(int val) { @@ -219,4 +219,4 @@ int ehci_hcd_stop(int index) { return omap_ehci_hcd_stop(); } -#endif /* CONFIG_USB_EHCI */ +#endif /* CONFIG_USB_EHCI_HCD */ diff --git a/board/technexion/twister/twister.c b/board/technexion/twister/twister.c index ad4b02a753..25aeebc8d0 100644 --- a/board/technexion/twister/twister.c +++ b/board/technexion/twister/twister.c @@ -19,7 +19,7 @@ #include <spl.h> #include <mmc.h> #include <asm/gpio.h> -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD #include <usb.h> #include <asm/ehci-omap.h> #endif @@ -46,7 +46,7 @@ static const u32 gpmc_XR16L2751[] = { XR16L2751_GPMC_CONFIG6, }; -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD static struct omap_usbhs_board_data usbhs_bdata = { .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, diff --git a/board/teejet/mt_ventoux/mt_ventoux.c b/board/teejet/mt_ventoux/mt_ventoux.c index 6b05541964..6e73ae114a 100644 --- a/board/teejet/mt_ventoux/mt_ventoux.c +++ b/board/teejet/mt_ventoux/mt_ventoux.c @@ -23,7 +23,7 @@ #include <i2c.h> #include <spartan3.h> #include <asm/gpio.h> -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD #include <usb.h> #include <asm/ehci-omap.h> #endif @@ -95,7 +95,7 @@ static const u32 gpmc_fpga[] = { FPGA_GPMC_CONFIG6, }; -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD static struct omap_usbhs_board_data usbhs_bdata = { .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, diff --git a/board/ti/am335x/board.c b/board/ti/am335x/board.c index 3e81521399..517965c0f0 100644 --- a/board/ti/am335x/board.c +++ b/board/ti/am335x/board.c @@ -72,7 +72,8 @@ void do_board_detect(void) enable_i2c0_pin_mux(); i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); - if (ti_i2c_eeprom_am_get(-1, CONFIG_SYS_I2C_EEPROM_ADDR)) + if (ti_i2c_eeprom_am_get(CONFIG_EEPROM_BUS_ADDRESS, + CONFIG_EEPROM_CHIP_ADDRESS)) printf("ti_i2c_eeprom_init failed\n"); } #endif diff --git a/board/ti/am43xx/board.c b/board/ti/am43xx/board.c index f633e2f85d..f44103d4d6 100644 --- a/board/ti/am43xx/board.c +++ b/board/ti/am43xx/board.c @@ -42,7 +42,8 @@ static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE; #ifdef CONFIG_TI_I2C_BOARD_DETECT void do_board_detect(void) { - if (ti_i2c_eeprom_am_get(-1, CONFIG_SYS_I2C_EEPROM_ADDR)) + if (ti_i2c_eeprom_am_get(CONFIG_EEPROM_BUS_ADDRESS, + CONFIG_EEPROM_CHIP_ADDRESS)) printf("ti_i2c_eeprom_init failed\n"); } #endif diff --git a/board/ti/beagle/beagle.c b/board/ti/beagle/beagle.c index dc38a80f59..00d127e21b 100644 --- a/board/ti/beagle/beagle.c +++ b/board/ti/beagle/beagle.c @@ -36,7 +36,7 @@ #include "beagle.h" #include <command.h> -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD #include <usb.h> #include <asm/ehci-omap.h> #endif @@ -538,7 +538,7 @@ void board_mmc_power_init(void) } #endif -#if defined(CONFIG_USB_EHCI) && !defined(CONFIG_SPL_BUILD) +#if defined(CONFIG_USB_EHCI_HCD) && !defined(CONFIG_SPL_BUILD) /* Call usb_stop() before starting the kernel */ void show_boot_progress(int val) { @@ -563,7 +563,7 @@ int ehci_hcd_stop(int index) return omap_ehci_hcd_stop(); } -#endif /* CONFIG_USB_EHCI */ +#endif /* CONFIG_USB_EHCI_HCD */ #if defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET) int board_eth_init(bd_t *bis) diff --git a/board/ti/omap5_uevm/evm.c b/board/ti/omap5_uevm/evm.c index 447f82c4ee..b6cc417333 100644 --- a/board/ti/omap5_uevm/evm.c +++ b/board/ti/omap5_uevm/evm.c @@ -20,7 +20,7 @@ #include "mux_data.h" -#if defined(CONFIG_USB_EHCI) || defined(CONFIG_USB_XHCI_OMAP) +#if defined(CONFIG_USB_EHCI_HCD) || defined(CONFIG_USB_XHCI_OMAP) #include <sata.h> #include <usb.h> #include <asm/gpio.h> @@ -151,7 +151,7 @@ int board_eth_init(bd_t *bis) return 0; } -#if defined(CONFIG_USB_EHCI) || defined(CONFIG_USB_XHCI_OMAP) +#if defined(CONFIG_USB_EHCI_HCD) || defined(CONFIG_USB_XHCI_OMAP) static void enable_host_clocks(void) { int auxclk; @@ -220,7 +220,7 @@ int board_mmc_init(bd_t *bis) } #endif -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD static struct omap_usbhs_board_data usbhs_bdata = { .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED, .port_mode[1] = OMAP_EHCI_PORT_MODE_HSIC, diff --git a/board/ti/panda/panda.c b/board/ti/panda/panda.c index 4db8f82a57..72aabb242c 100644 --- a/board/ti/panda/panda.c +++ b/board/ti/panda/panda.c @@ -15,7 +15,7 @@ #include "panda_mux_data.h" -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD #include <usb.h> #include <asm/arch/ehci.h> #include <asm/ehci-omap.h> @@ -301,7 +301,7 @@ void board_mmc_power_init(void) #endif #endif -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD static struct omap_usbhs_board_data usbhs_bdata = { .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, diff --git a/board/tqc/tqm5200/tqm5200.c b/board/tqc/tqm5200/tqm5200.c index 92db093dbf..c48ab11fc4 100644 --- a/board/tqc/tqm5200/tqm5200.c +++ b/board/tqc/tqm5200/tqm5200.c @@ -486,20 +486,14 @@ int board_early_init_f (void) static int tfp410_read_reg(int reg, uchar *buf) { - if (i2c_read(CONFIG_SYS_TFP410_ADDR, reg, 1, buf, 1) != 0) { - puts ("Error reading the chip.\n"); - return 1; - } - return 0; + puts("Error reading the chip.\n"); + return -ENOSYS; } static int tfp410_write_reg(int reg, uchar buf) { - if (i2c_write(CONFIG_SYS_TFP410_ADDR, reg, 1, &buf, 1) != 0) { - puts ("Error writing the chip.\n"); - return 1; - } - return 0; + puts("Error writing the chip.\n"); + return -ENOSYS; } typedef struct _tfp410_config { @@ -525,12 +519,9 @@ static int charon_last_stage_init(void) { volatile struct mpc5xxx_lpb *lpb = (struct mpc5xxx_lpb *) MPC5XXX_LPB; - int oldbus = i2c_get_bus_num(); uchar buf; int i = 0; - i2c_set_bus_num(CONFIG_SYS_TFP410_BUS); - /* check version */ if (tfp410_read_reg(TFP410_REG_DEV_ID_H, &buf) != 0) return -1; @@ -551,7 +542,6 @@ static int charon_last_stage_init(void) i++; } printf("TFP410 initialized.\n"); - i2c_set_bus_num(oldbus); /* set deadcycle for cs3 to 0 */ setbits_be32(&lpb->cs_deadcycle, 0xffffcfff); diff --git a/cmd/eeprom.c b/cmd/eeprom.c index 0a0e4a2c1c..e43566bc56 100644 --- a/cmd/eeprom.c +++ b/cmd/eeprom.c @@ -73,11 +73,9 @@ void eeprom_init(int bus) #endif /* I2C EEPROM */ -#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C) #if defined(CONFIG_SYS_I2C) if (bus >= 0) i2c_set_bus_num(bus); -#endif i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); #endif } diff --git a/common/board_f.c b/common/board_f.c index d9431ee79a..a212f2b539 100644 --- a/common/board_f.c +++ b/common/board_f.c @@ -184,7 +184,7 @@ __weak int dram_init_banksize(void) return 0; } -#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C) +#if defined(CONFIG_SYS_I2C) static int init_func_i2c(void) { puts("I2C: "); @@ -740,7 +740,9 @@ static const init_fnc_t init_sequence_f[] = { /* get CPU and bus clocks according to the environment variable */ get_clocks, /* get CPU and bus clocks (etc.) */ #endif +#if !defined(CONFIG_M68K) timer_init, /* initialize timer */ +#endif #if defined(CONFIG_BOARD_POSTCLK_INIT) board_postclk_init, #endif @@ -765,7 +767,7 @@ static const init_fnc_t init_sequence_f[] = { misc_init_f, #endif INIT_FUNC_WATCHDOG_RESET -#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C) +#if defined(CONFIG_SYS_I2C) init_func_i2c, #endif #if defined(CONFIG_HARD_SPI) diff --git a/common/board_r.c b/common/board_r.c index 9f34b85a74..28f32c3885 100644 --- a/common/board_r.c +++ b/common/board_r.c @@ -485,24 +485,7 @@ static int initr_env(void) /* Initialize from environment */ load_addr = getenv_ulong("loadaddr", 16, load_addr); -#if defined(CONFIG_SYS_EXTBDINFO) -#if defined(CONFIG_405GP) || defined(CONFIG_405EP) -#if defined(CONFIG_I2CFAST) - /* - * set bi_iic_fast for linux taking environment variable - * "i2cfast" into account - */ - { - char *s = getenv("i2cfast"); - if (s && ((*s == 'y') || (*s == 'Y'))) { - gd->bd->bi_iic_fast[0] = 1; - gd->bd->bi_iic_fast[1] = 1; - } - } -#endif /* CONFIG_I2CFAST */ -#endif /* CONFIG_405GP, CONFIG_405EP */ -#endif /* CONFIG_SYS_EXTBDINFO */ return 0; } diff --git a/common/edid.c b/common/edid.c index e08e420920..19410aa4fc 100644 --- a/common/edid.c +++ b/common/edid.c @@ -85,6 +85,7 @@ static void decode_timing(u8 *buf, struct display_timing *timing) uint x_mm, y_mm; unsigned int ha, hbl, hso, hspw, hborder; unsigned int va, vbl, vso, vspw, vborder; + struct edid_detailed_timing *t = (struct edid_detailed_timing *)buf; /* Edid contains pixel clock in terms of 10KHz */ set_entry(&timing->pixelclock, (buf[0] + (buf[1] << 8)) * 10000); @@ -111,6 +112,19 @@ static void decode_timing(u8 *buf, struct display_timing *timing) set_entry(&timing->vback_porch, vbl - vso - vspw); set_entry(&timing->vsync_len, vspw); + timing->flags = 0; + if (EDID_DETAILED_TIMING_FLAG_HSYNC_POLARITY(*t)) + timing->flags |= DISPLAY_FLAGS_HSYNC_HIGH; + else + timing->flags |= DISPLAY_FLAGS_HSYNC_LOW; + if (EDID_DETAILED_TIMING_FLAG_VSYNC_POLARITY(*t)) + timing->flags |= DISPLAY_FLAGS_VSYNC_HIGH; + else + timing->flags |= DISPLAY_FLAGS_VSYNC_LOW; + + if (EDID_DETAILED_TIMING_FLAG_INTERLACED(*t)) + timing->flags = DISPLAY_FLAGS_INTERLACED; + debug("Detailed mode clock %u Hz, %d mm x %d mm\n" " %04x %04x %04x %04x hborder %x\n" " %04x %04x %04x %04x vborder %x\n", @@ -122,6 +136,39 @@ static void decode_timing(u8 *buf, struct display_timing *timing) va + vbl, vborder); } +/** + * Check if HDMI vendor specific data block is present in CEA block + * @param info CEA extension block + * @return true if block is found + */ +static bool cea_is_hdmi_vsdb_present(struct edid_cea861_info *info) +{ + u8 end, i = 0; + + /* check for end of data block */ + end = info->dtd_offset; + if (end == 0) + end = 127; + if (end < 4 || end > 127) + return false; + end -= 4; + + while (i < end) { + /* Look for vendor specific data block of appropriate size */ + if ((EDID_CEA861_DB_TYPE(*info, i) == EDID_CEA861_DB_VENDOR) && + (EDID_CEA861_DB_LEN(*info, i) >= 5)) { + u8 *db = &info->data[i + 1]; + u32 oui = db[0] | (db[1] << 8) | (db[2] << 16); + + if (oui == HDMI_IEEE_OUI) + return true; + } + i += EDID_CEA861_DB_LEN(*info, i) + 1; + } + + return false; +} + int edid_get_timing(u8 *buf, int buf_size, struct display_timing *timing, int *panel_bits_per_colourp) { @@ -167,6 +214,15 @@ int edid_get_timing(u8 *buf, int buf_size, struct display_timing *timing, ((edid->video_input_definition & 0x70) >> 3) + 4; } + timing->hdmi_monitor = false; + if (edid->extension_flag && (buf_size >= EDID_EXT_SIZE)) { + struct edid_cea861_info *info = + (struct edid_cea861_info *)(buf + sizeof(*edid)); + + if (info->extension_tag == EDID_CEA861_EXTENSION_TAG) + timing->hdmi_monitor = cea_is_hdmi_vsdb_present(info); + } + return 0; } diff --git a/common/lcd.c b/common/lcd.c index 783626e3d5..2405146cf0 100644 --- a/common/lcd.c +++ b/common/lcd.c @@ -704,7 +704,7 @@ int lcd_display_bitmap(ulong bmp_image, int x, int y) } break; #endif /* CONFIG_BMP_16BPP */ -#if defined(CONFIG_BMP_24BMP) +#if defined(CONFIG_BMP_24BPP) case 24: for (i = 0; i < height; ++i) { for (j = 0; j < width; j++) { @@ -716,7 +716,7 @@ int lcd_display_bitmap(ulong bmp_image, int x, int y) fb -= lcd_line_length + width * (bpix / 8); } break; -#endif /* CONFIG_BMP_24BMP */ +#endif /* CONFIG_BMP_24BPP */ #if defined(CONFIG_BMP_32BPP) case 32: for (i = 0; i < height; ++i) { diff --git a/common/spl/Kconfig b/common/spl/Kconfig index e82a87947b..5ed3f19ac3 100644 --- a/common/spl/Kconfig +++ b/common/spl/Kconfig @@ -693,6 +693,20 @@ config SPL_YMODEM_SUPPORT means of transmitting U-Boot over a serial line for using in SPL, with a checksum to ensure correctness. +config SPL_ATF_SUPPORT + bool "Support ARM Trusted Firmware" + depends on SPL && ARM64 + help + ATF(ARM Trusted Firmware) is a component for ARM arch64 which which + is loaded by SPL(which is considered as BL2 in ATF terminology). + More detail at: https://github.com/ARM-software/arm-trusted-firmware + +config SPL_ATF_TEXT_BASE + depends on SPL_ATF_SUPPORT + hex "ATF BL31 base address" + help + This is the base address in memory for ATF BL31 text and entry point. + config TPL_ENV_SUPPORT bool "Support an environment" depends on TPL diff --git a/common/spl/Makefile b/common/spl/Makefile index 1933cbdfed..b3b34d6277 100644 --- a/common/spl/Makefile +++ b/common/spl/Makefile @@ -20,6 +20,7 @@ endif obj-$(CONFIG_SPL_UBI) += spl_ubi.o obj-$(CONFIG_SPL_NET_SUPPORT) += spl_net.o obj-$(CONFIG_SPL_MMC_SUPPORT) += spl_mmc.o +obj-$(CONFIG_SPL_ATF_SUPPORT) += spl_atf.o obj-$(CONFIG_SPL_USB_SUPPORT) += spl_usb.o obj-$(CONFIG_SPL_FAT_SUPPORT) += spl_fat.o obj-$(CONFIG_SPL_EXT_SUPPORT) += spl_ext.o diff --git a/common/spl/spl.c b/common/spl/spl.c index df984b8efd..0a49766f21 100644 --- a/common/spl/spl.c +++ b/common/spl/spl.c @@ -415,6 +415,11 @@ void board_init_r(gd_t *dummy1, ulong dummy2) gd->malloc_ptr / 1024); #endif + if (IS_ENABLED(CONFIG_SPL_ATF_SUPPORT)) { + debug("loaded - jumping to U-Boot via ATF BL31.\n"); + bl31_entry(); + } + debug("loaded - jumping to U-Boot...\n"); spl_board_prepare_for_boot(); jump_to_image_no_args(&spl_image); diff --git a/common/spl/spl_atf.c b/common/spl/spl_atf.c new file mode 100644 index 0000000000..6e8f928044 --- /dev/null +++ b/common/spl/spl_atf.c @@ -0,0 +1,97 @@ +/* + * Reference to the ARM TF Project, + * plat/arm/common/arm_bl2_setup.c + * Portions copyright (c) 2013-2016, ARM Limited and Contributors. All rights + * reserved. + * Copyright (C) 2016 Rockchip Electronic Co.,Ltd + * Written by Kever Yang <kever.yang@rock-chips.com> + * + * SPDX-License-Identifier: BSD-3-Clause + */ + +#include <common.h> +#include <atf_common.h> +#include <errno.h> +#include <spl.h> + +static struct bl2_to_bl31_params_mem bl31_params_mem; +static struct bl31_params *bl2_to_bl31_params; + +/** + * bl2_plat_get_bl31_params() - prepare params for bl31. + * + * This function assigns a pointer to the memory that the platform has kept + * aside to pass platform specific and trusted firmware related information + * to BL31. This memory is allocated by allocating memory to + * bl2_to_bl31_params_mem structure which is a superset of all the + * structure whose information is passed to BL31 + * NOTE: This function should be called only once and should be done + * before generating params to BL31 + * + * @return bl31 params structure pointer + */ +struct bl31_params *bl2_plat_get_bl31_params(void) +{ + struct entry_point_info *bl33_ep_info; + + /* + * Initialise the memory for all the arguments that needs to + * be passed to BL31 + */ + memset(&bl31_params_mem, 0, sizeof(struct bl2_to_bl31_params_mem)); + + /* Assign memory for TF related information */ + bl2_to_bl31_params = &bl31_params_mem.bl31_params; + SET_PARAM_HEAD(bl2_to_bl31_params, ATF_PARAM_BL31, ATF_VERSION_1, 0); + + /* Fill BL31 related information */ + SET_PARAM_HEAD(bl2_to_bl31_params->bl31_image_info, + ATF_PARAM_IMAGE_BINARY, ATF_VERSION_1, 0); + + /* Fill BL32 related information if it exists */ +#ifdef BL32_BASE + bl2_to_bl31_params->bl32_ep_info = &bl31_params_mem.bl32_ep_info; + SET_PARAM_HEAD(bl2_to_bl31_params->bl32_ep_info, ATF_PARAM_EP, + ATF_VERSION_1, 0); + bl2_to_bl31_params->bl32_image_info = &bl31_params_mem.bl32_image_info; + SET_PARAM_HEAD(bl2_to_bl31_params->bl32_image_info, + ATF_PARAM_IMAGE_BINARY, ATF_VERSION_1, 0); +#endif /* BL32_BASE */ + + /* Fill BL33 related information */ + bl2_to_bl31_params->bl33_ep_info = &bl31_params_mem.bl33_ep_info; + bl33_ep_info = &bl31_params_mem.bl33_ep_info; + SET_PARAM_HEAD(bl33_ep_info, ATF_PARAM_EP, ATF_VERSION_1, + ATF_EP_NON_SECURE); + + /* BL33 expects to receive the primary CPU MPID (through x0) */ + bl33_ep_info->args.arg0 = 0xffff & read_mpidr(); + bl33_ep_info->pc = CONFIG_SYS_TEXT_BASE; + bl33_ep_info->spsr = SPSR_64(MODE_EL2, MODE_SP_ELX, + DISABLE_ALL_EXECPTIONS); + + bl2_to_bl31_params->bl33_image_info = &bl31_params_mem.bl33_image_info; + SET_PARAM_HEAD(bl2_to_bl31_params->bl33_image_info, + ATF_PARAM_IMAGE_BINARY, ATF_VERSION_1, 0); + + return bl2_to_bl31_params; +} + +void raw_write_daif(unsigned int daif) +{ + __asm__ __volatile__("msr DAIF, %0\n\t" : : "r" (daif) : "memory"); +} + +void bl31_entry(void) +{ + struct bl31_params *bl31_params; + void (*entry)(struct bl31_params *params, void *plat_params) = NULL; + + bl31_params = bl2_plat_get_bl31_params(); + entry = (void *)CONFIG_SPL_ATF_TEXT_BASE; + + raw_write_daif(SPSR_EXCEPTION_MASK); + dcache_disable(); + + entry(bl31_params, NULL); +} diff --git a/common/stdio.c b/common/stdio.c index 4d30017530..ee4f0bda9e 100644 --- a/common/stdio.c +++ b/common/stdio.c @@ -21,7 +21,7 @@ #include <logbuff.h> #endif -#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C) +#if defined(CONFIG_SYS_I2C) #include <i2c.h> #endif @@ -346,9 +346,6 @@ int stdio_add_devices(void) #ifdef CONFIG_SYS_I2C i2c_init_all(); #else -#if defined(CONFIG_HARD_I2C) - i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); -#endif #endif #ifdef CONFIG_DM_VIDEO /* diff --git a/common/usb_storage.c b/common/usb_storage.c index 83279c449d..03171f74cb 100644 --- a/common/usb_storage.c +++ b/common/usb_storage.c @@ -100,7 +100,7 @@ struct us_data { trans_cmnd transport; /* transport routine */ }; -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD /* * The U-Boot EHCI driver can handle any transfer length as long as there is * enough free heap space left, but the SCSI READ(10) and WRITE(10) commands are diff --git a/configs/MPC8315ERDB_defconfig b/configs/MPC8315ERDB_defconfig index dbe060f001..38417e7964 100644 --- a/configs/MPC8315ERDB_defconfig +++ b/configs/MPC8315ERDB_defconfig @@ -16,5 +16,6 @@ CONFIG_CMD_EXT2=y CONFIG_MTD_NOR_FLASH=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/MPC8349ITX_LOWBOOT_defconfig b/configs/MPC8349ITX_LOWBOOT_defconfig index a97ce25a28..4a7ff1b9eb 100644 --- a/configs/MPC8349ITX_LOWBOOT_defconfig +++ b/configs/MPC8349ITX_LOWBOOT_defconfig @@ -20,5 +20,6 @@ CONFIG_CMD_FAT=y CONFIG_MTD_NOR_FLASH=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/MPC8349ITX_defconfig b/configs/MPC8349ITX_defconfig index c61f260dc3..7c67d8c01e 100644 --- a/configs/MPC8349ITX_defconfig +++ b/configs/MPC8349ITX_defconfig @@ -20,5 +20,6 @@ CONFIG_CMD_FAT=y CONFIG_MTD_NOR_FLASH=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/MPC837XEMDS_HOST_defconfig b/configs/MPC837XEMDS_HOST_defconfig index 774ecb81b5..787ac9dbce 100644 --- a/configs/MPC837XEMDS_HOST_defconfig +++ b/configs/MPC837XEMDS_HOST_defconfig @@ -17,5 +17,6 @@ CONFIG_CMD_FAT=y CONFIG_MTD_NOR_FLASH=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/MPC837XERDB_defconfig b/configs/MPC837XERDB_defconfig index 717fee1cfe..2f3e7b0162 100644 --- a/configs/MPC837XERDB_defconfig +++ b/configs/MPC837XERDB_defconfig @@ -17,5 +17,6 @@ CONFIG_CMD_FAT=y CONFIG_MTD_NOR_FLASH=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/MiniFAP_defconfig b/configs/MiniFAP_defconfig index 7d719f81f5..02ca577e28 100644 --- a/configs/MiniFAP_defconfig +++ b/configs/MiniFAP_defconfig @@ -10,7 +10,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -19,7 +18,6 @@ CONFIG_CMD_PING=y CONFIG_CMD_SNTP=y CONFIG_CMD_BMP=y CONFIG_CMD_BSP=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/O2D300_defconfig b/configs/O2D300_defconfig index 38101f05df..c0e9541b87 100644 --- a/configs/O2D300_defconfig +++ b/configs/O2D300_defconfig @@ -4,7 +4,6 @@ CONFIG_TARGET_O2D300=y CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/O2DNT2_RAMBOOT_defconfig b/configs/O2DNT2_RAMBOOT_defconfig index 83006e5582..8cff44cf36 100644 --- a/configs/O2DNT2_RAMBOOT_defconfig +++ b/configs/O2DNT2_RAMBOOT_defconfig @@ -8,7 +8,6 @@ CONFIG_HUSH_PARSER=y CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press password to stop\n" CONFIG_AUTOBOOT_STOP_STR="++++++++++" -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/O2DNT2_defconfig b/configs/O2DNT2_defconfig index 4202d85203..f29abb83bc 100644 --- a/configs/O2DNT2_defconfig +++ b/configs/O2DNT2_defconfig @@ -7,7 +7,6 @@ CONFIG_HUSH_PARSER=y CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press password to stop\n" CONFIG_AUTOBOOT_STOP_STR="++++++++++" -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/O2D_defconfig b/configs/O2D_defconfig index b84a1c8839..534cfe12e2 100644 --- a/configs/O2D_defconfig +++ b/configs/O2D_defconfig @@ -4,7 +4,6 @@ CONFIG_TARGET_O2D=y CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/O2I_defconfig b/configs/O2I_defconfig index efcc769ff4..acf42abe29 100644 --- a/configs/O2I_defconfig +++ b/configs/O2I_defconfig @@ -4,7 +4,6 @@ CONFIG_TARGET_O2I=y CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/O2MNT_O2M110_defconfig b/configs/O2MNT_O2M110_defconfig index abdc53df21..de647c76b9 100644 --- a/configs/O2MNT_O2M110_defconfig +++ b/configs/O2MNT_O2M110_defconfig @@ -5,7 +5,6 @@ CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_EXTRA_OPTIONS="IFM_SENSOR_TYPE=\"O2M110\"" CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/O2MNT_O2M112_defconfig b/configs/O2MNT_O2M112_defconfig index 06089fe3cf..b243e9cc0e 100644 --- a/configs/O2MNT_O2M112_defconfig +++ b/configs/O2MNT_O2M112_defconfig @@ -5,7 +5,6 @@ CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_EXTRA_OPTIONS="IFM_SENSOR_TYPE=\"O2M112\"" CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/O2MNT_O2M113_defconfig b/configs/O2MNT_O2M113_defconfig index 1ea3f3a09b..1584058289 100644 --- a/configs/O2MNT_O2M113_defconfig +++ b/configs/O2MNT_O2M113_defconfig @@ -5,7 +5,6 @@ CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_EXTRA_OPTIONS="IFM_SENSOR_TYPE=\"O2M113\"" CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/O2MNT_defconfig b/configs/O2MNT_defconfig index 0209085605..20bd31466e 100644 --- a/configs/O2MNT_defconfig +++ b/configs/O2MNT_defconfig @@ -4,7 +4,6 @@ CONFIG_TARGET_O2MNT=y CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/O3DNT_defconfig b/configs/O3DNT_defconfig index 5ce4140859..ea769e7edc 100644 --- a/configs/O3DNT_defconfig +++ b/configs/O3DNT_defconfig @@ -4,7 +4,6 @@ CONFIG_TARGET_O3DNT=y CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/TQM5200S_HIGHBOOT_defconfig b/configs/TQM5200S_HIGHBOOT_defconfig index d0cd50a63c..d07596add0 100644 --- a/configs/TQM5200S_HIGHBOOT_defconfig +++ b/configs/TQM5200S_HIGHBOOT_defconfig @@ -7,7 +7,6 @@ CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -15,7 +14,6 @@ CONFIG_CMD_MII=y CONFIG_CMD_PING=y CONFIG_CMD_SNTP=y CONFIG_CMD_BSP=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/TQM5200S_defconfig b/configs/TQM5200S_defconfig index 5324a9a11c..af3225554b 100644 --- a/configs/TQM5200S_defconfig +++ b/configs/TQM5200S_defconfig @@ -7,7 +7,6 @@ CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -15,7 +14,6 @@ CONFIG_CMD_MII=y CONFIG_CMD_PING=y CONFIG_CMD_SNTP=y CONFIG_CMD_BSP=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/TQM5200_B_HIGHBOOT_defconfig b/configs/TQM5200_B_HIGHBOOT_defconfig index 2f933e6cab..37d6767f28 100644 --- a/configs/TQM5200_B_HIGHBOOT_defconfig +++ b/configs/TQM5200_B_HIGHBOOT_defconfig @@ -10,7 +10,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -19,7 +18,6 @@ CONFIG_CMD_PING=y CONFIG_CMD_SNTP=y CONFIG_CMD_BMP=y CONFIG_CMD_BSP=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/TQM5200_B_defconfig b/configs/TQM5200_B_defconfig index f204484f59..5e0cf9ea47 100644 --- a/configs/TQM5200_B_defconfig +++ b/configs/TQM5200_B_defconfig @@ -10,7 +10,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -19,7 +18,6 @@ CONFIG_CMD_PING=y CONFIG_CMD_SNTP=y CONFIG_CMD_BMP=y CONFIG_CMD_BSP=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/TQM5200_STK100_defconfig b/configs/TQM5200_STK100_defconfig index db9bb8a30d..7b4b030d74 100644 --- a/configs/TQM5200_STK100_defconfig +++ b/configs/TQM5200_STK100_defconfig @@ -10,7 +10,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -19,7 +18,6 @@ CONFIG_CMD_PING=y CONFIG_CMD_SNTP=y CONFIG_CMD_BMP=y CONFIG_CMD_BSP=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/TQM5200_defconfig b/configs/TQM5200_defconfig index eec60f1be4..4792639653 100644 --- a/configs/TQM5200_defconfig +++ b/configs/TQM5200_defconfig @@ -9,7 +9,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -18,7 +17,6 @@ CONFIG_CMD_PING=y CONFIG_CMD_SNTP=y CONFIG_CMD_BMP=y CONFIG_CMD_BSP=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/a4m072_defconfig b/configs/a4m072_defconfig index ce5edcbf01..0054d4cddb 100644 --- a/configs/a4m072_defconfig +++ b/configs/a4m072_defconfig @@ -7,7 +7,6 @@ CONFIG_HUSH_PARSER=y CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="autoboot in %d seconds\n" CONFIG_AUTOBOOT_DELAY_STR="asdfg" -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y diff --git a/configs/ac14xx_defconfig b/configs/ac14xx_defconfig index e3b7793e04..930ec8acf2 100644 --- a/configs/ac14xx_defconfig +++ b/configs/ac14xx_defconfig @@ -5,7 +5,6 @@ CONFIG_FIT=y CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_PROMPT="ac14xx> " CONFIG_CMD_ASKENV=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/alt_defconfig b/configs/alt_defconfig index b8e2864ff4..04dda72532 100644 --- a/configs/alt_defconfig +++ b/configs/alt_defconfig @@ -25,4 +25,5 @@ CONFIG_SPI_FLASH_BAR=y CONFIG_SPI_FLASH_SPANSION=y CONFIG_BAUDRATE=38400 CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y diff --git a/configs/ap_sh4a_4a_defconfig b/configs/ap_sh4a_4a_defconfig index 75cf53fe21..41c8be9120 100644 --- a/configs/ap_sh4a_4a_defconfig +++ b/configs/ap_sh4a_4a_defconfig @@ -13,7 +13,6 @@ CONFIG_VERSION_VARIABLE=y # CONFIG_CMD_ENV_EXISTS is not set # CONFIG_CMD_LOADB is not set # CONFIG_CMD_LOADS is not set -CONFIG_CMD_I2C=y # CONFIG_CMD_FPGA is not set # CONFIG_CMD_ECHO is not set # CONFIG_CMD_ITEST is not set diff --git a/configs/apalis-tk1_defconfig b/configs/apalis-tk1_defconfig index 648be92fcb..74cea3170e 100644 --- a/configs/apalis-tk1_defconfig +++ b/configs/apalis-tk1_defconfig @@ -38,6 +38,7 @@ CONFIG_PMIC_AS3722=y CONFIG_SYS_NS16550=y CONFIG_USB=y CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_CI_UDC=y diff --git a/configs/apalis_imx6_defconfig b/configs/apalis_imx6_defconfig index d4dc1d3865..90829b4949 100644 --- a/configs/apalis_imx6_defconfig +++ b/configs/apalis_imx6_defconfig @@ -40,7 +40,6 @@ CONFIG_CMD_EXT4=y CONFIG_CMD_FAT=y CONFIG_CMD_FS_GENERIC=y CONFIG_USB=y -CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_CI_UDC=y diff --git a/configs/apalis_imx6_nospl_com_defconfig b/configs/apalis_imx6_nospl_com_defconfig index 87affc0bdb..ef9ca60b42 100644 --- a/configs/apalis_imx6_nospl_com_defconfig +++ b/configs/apalis_imx6_nospl_com_defconfig @@ -33,7 +33,6 @@ CONFIG_CMD_EXT4=y CONFIG_CMD_FAT=y CONFIG_CMD_FS_GENERIC=y CONFIG_USB=y -CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_CI_UDC=y diff --git a/configs/apalis_imx6_nospl_it_defconfig b/configs/apalis_imx6_nospl_it_defconfig index 97a4d2c1ed..f48bd17c42 100644 --- a/configs/apalis_imx6_nospl_it_defconfig +++ b/configs/apalis_imx6_nospl_it_defconfig @@ -33,7 +33,6 @@ CONFIG_CMD_EXT4=y CONFIG_CMD_FAT=y CONFIG_CMD_FS_GENERIC=y CONFIG_USB=y -CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_CI_UDC=y diff --git a/configs/apalis_t30_defconfig b/configs/apalis_t30_defconfig index a31b912968..8557df9c3f 100644 --- a/configs/apalis_t30_defconfig +++ b/configs/apalis_t30_defconfig @@ -37,6 +37,7 @@ CONFIG_PCI_TEGRA=y CONFIG_SYS_NS16550=y CONFIG_USB=y CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_CI_UDC=y diff --git a/configs/apx4devkit_defconfig b/configs/apx4devkit_defconfig index e2061a2cce..8bc1770ec2 100644 --- a/configs/apx4devkit_defconfig +++ b/configs/apx4devkit_defconfig @@ -14,18 +14,17 @@ CONFIG_HUSH_PARSER=y # CONFIG_CMD_IMLS is not set # CONFIG_CMD_FLASH is not set CONFIG_CMD_MMC=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_PING=y CONFIG_CMD_CACHE=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_UBI=y CONFIG_MMC_MXS=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/aria_defconfig b/configs/aria_defconfig index 963661ab2d..0f1432f9a8 100644 --- a/configs/aria_defconfig +++ b/configs/aria_defconfig @@ -5,7 +5,6 @@ CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/arndale_defconfig b/configs/arndale_defconfig index a2cde44386..0f2aa16e0e 100644 --- a/configs/arndale_defconfig +++ b/configs/arndale_defconfig @@ -34,4 +34,5 @@ CONFIG_USB=y CONFIG_DM_USB=y CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_DWC3=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y diff --git a/configs/aspenite_defconfig b/configs/aspenite_defconfig index 26654426ed..0ac39eabd2 100644 --- a/configs/aspenite_defconfig +++ b/configs/aspenite_defconfig @@ -6,7 +6,6 @@ CONFIG_BOOTDELAY=3 CONFIG_BOARD_EARLY_INIT_F=y # CONFIG_CMD_IMLS is not set # CONFIG_CMD_FLASH is not set -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set # CONFIG_CMD_NET is not set # CONFIG_CMD_NFS is not set diff --git a/configs/beaver_defconfig b/configs/beaver_defconfig index 0365246ee5..76359c9d2f 100644 --- a/configs/beaver_defconfig +++ b/configs/beaver_defconfig @@ -42,6 +42,7 @@ CONFIG_SYS_NS16550=y CONFIG_TEGRA20_SLINK=y CONFIG_USB=y CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_CI_UDC=y diff --git a/configs/brppt1_mmc_defconfig b/configs/brppt1_mmc_defconfig index 7d92c13940..1bdbf90495 100644 --- a/configs/brppt1_mmc_defconfig +++ b/configs/brppt1_mmc_defconfig @@ -57,4 +57,5 @@ CONFIG_USB_MUSB_HOST=y CONFIG_USB_STORAGE=y CONFIG_SYS_WHITE_ON_BLACK=y CONFIG_LCD=y +CONFIG_OMAP_WATCHDOG=y CONFIG_OF_LIBFDT=y diff --git a/configs/brppt1_nand_defconfig b/configs/brppt1_nand_defconfig index 9abe61760e..ed7432d7f4 100644 --- a/configs/brppt1_nand_defconfig +++ b/configs/brppt1_nand_defconfig @@ -57,4 +57,5 @@ CONFIG_USB_MUSB_HOST=y CONFIG_USB_STORAGE=y CONFIG_SYS_WHITE_ON_BLACK=y CONFIG_LCD=y +CONFIG_OMAP_WATCHDOG=y CONFIG_OF_LIBFDT=y diff --git a/configs/brppt1_spi_defconfig b/configs/brppt1_spi_defconfig index 79bb9057bf..02b5ff60e2 100644 --- a/configs/brppt1_spi_defconfig +++ b/configs/brppt1_spi_defconfig @@ -65,4 +65,5 @@ CONFIG_USB_MUSB_HOST=y CONFIG_USB_STORAGE=y CONFIG_SYS_WHITE_ON_BLACK=y CONFIG_LCD=y +CONFIG_OMAP_WATCHDOG=y CONFIG_OF_LIBFDT=y diff --git a/configs/cam5200_defconfig b/configs/cam5200_defconfig index 92985ab3d6..46a24f56ab 100644 --- a/configs/cam5200_defconfig +++ b/configs/cam5200_defconfig @@ -7,14 +7,12 @@ CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_PING=y CONFIG_CMD_SNTP=y CONFIG_CMD_BSP=y -CONFIG_CMD_DATE=y CONFIG_MAC_PARTITION=y CONFIG_DOS_PARTITION=y CONFIG_ISO_PARTITION=y diff --git a/configs/cam5200_niosflash_defconfig b/configs/cam5200_niosflash_defconfig index 32bc58ee9b..6b9877ff21 100644 --- a/configs/cam5200_niosflash_defconfig +++ b/configs/cam5200_niosflash_defconfig @@ -7,14 +7,12 @@ CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_PING=y CONFIG_CMD_SNTP=y CONFIG_CMD_BSP=y -CONFIG_CMD_DATE=y CONFIG_MAC_PARTITION=y CONFIG_DOS_PARTITION=y CONFIG_ISO_PARTITION=y diff --git a/configs/cardhu_defconfig b/configs/cardhu_defconfig index 77dac784e3..76e861a3a2 100644 --- a/configs/cardhu_defconfig +++ b/configs/cardhu_defconfig @@ -37,4 +37,5 @@ CONFIG_SYS_NS16550=y CONFIG_TEGRA20_SLINK=y CONFIG_USB=y CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y diff --git a/configs/cei-tk1-som_defconfig b/configs/cei-tk1-som_defconfig index dd6fd498b7..c1b4486d87 100644 --- a/configs/cei-tk1-som_defconfig +++ b/configs/cei-tk1-som_defconfig @@ -43,6 +43,7 @@ CONFIG_SYS_NS16550=y CONFIG_TEGRA114_SPI=y CONFIG_USB=y CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_CI_UDC=y diff --git a/configs/charon_defconfig b/configs/charon_defconfig index ec22a6368f..8a1429037a 100644 --- a/configs/charon_defconfig +++ b/configs/charon_defconfig @@ -9,7 +9,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y diff --git a/configs/cm5200_defconfig b/configs/cm5200_defconfig index 7d8d01aaaa..d3369f4455 100644 --- a/configs/cm5200_defconfig +++ b/configs/cm5200_defconfig @@ -6,7 +6,6 @@ CONFIG_BOOTDELAY=5 CONFIG_SILENT_CONSOLE=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y diff --git a/configs/cm_fx6_defconfig b/configs/cm_fx6_defconfig index 33b53160a7..5a371c7e81 100644 --- a/configs/cm_fx6_defconfig +++ b/configs/cm_fx6_defconfig @@ -52,7 +52,6 @@ CONFIG_SPI_FLASH_STMICRO=y CONFIG_SPI_FLASH_SST=y CONFIG_SPI_FLASH_WINBOND=y CONFIG_USB=y -CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_USB_KEYBOARD=y CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y diff --git a/configs/cm_t35_defconfig b/configs/cm_t35_defconfig index b9a79408a2..868d175d22 100644 --- a/configs/cm_t35_defconfig +++ b/configs/cm_t35_defconfig @@ -35,6 +35,7 @@ CONFIG_LED_STATUS_BOOT=0 CONFIG_MMC_OMAP_HS=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_LCD=y CONFIG_OF_LIBFDT=y diff --git a/configs/cm_t54_defconfig b/configs/cm_t54_defconfig index d7fd995f7a..067945636f 100644 --- a/configs/cm_t54_defconfig +++ b/configs/cm_t54_defconfig @@ -2,6 +2,7 @@ CONFIG_ARM=y CONFIG_ARCH_OMAP2PLUS=y CONFIG_OMAP54XX=y CONFIG_TARGET_CM_T54=y +CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC=16296 # CONFIG_SPL_NAND_SUPPORT is not set CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=3 @@ -37,5 +38,6 @@ CONFIG_EFI_PARTITION=y CONFIG_MMC_OMAP_HS=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/colibri_imx6_defconfig b/configs/colibri_imx6_defconfig index 6ab2b9d6ef..47e8198e77 100644 --- a/configs/colibri_imx6_defconfig +++ b/configs/colibri_imx6_defconfig @@ -40,7 +40,6 @@ CONFIG_CMD_EXT4=y CONFIG_CMD_FAT=y CONFIG_CMD_FS_GENERIC=y CONFIG_USB=y -CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_CI_UDC=y diff --git a/configs/colibri_imx6_nospl_defconfig b/configs/colibri_imx6_nospl_defconfig index 93897fff96..52e0d50411 100644 --- a/configs/colibri_imx6_nospl_defconfig +++ b/configs/colibri_imx6_nospl_defconfig @@ -33,7 +33,6 @@ CONFIG_CMD_EXT4=y CONFIG_CMD_FAT=y CONFIG_CMD_FS_GENERIC=y CONFIG_USB=y -CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_CI_UDC=y diff --git a/configs/colibri_t20_defconfig b/configs/colibri_t20_defconfig index 5f6114ed6d..db0224b929 100644 --- a/configs/colibri_t20_defconfig +++ b/configs/colibri_t20_defconfig @@ -41,6 +41,7 @@ CONFIG_PWM_TEGRA=y CONFIG_SYS_NS16550=y CONFIG_USB=y CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_ULPI_VIEWPORT=y CONFIG_USB_ULPI=y CONFIG_USB_STORAGE=y diff --git a/configs/colibri_t30_defconfig b/configs/colibri_t30_defconfig index 0071a923e4..41cc0ed340 100644 --- a/configs/colibri_t30_defconfig +++ b/configs/colibri_t30_defconfig @@ -32,6 +32,7 @@ CONFIG_DFU_RAM=y CONFIG_SYS_NS16550=y CONFIG_USB=y CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_CI_UDC=y diff --git a/configs/colibri_vf_defconfig b/configs/colibri_vf_defconfig index 78c478f420..b69ce65224 100644 --- a/configs/colibri_vf_defconfig +++ b/configs/colibri_vf_defconfig @@ -46,6 +46,7 @@ CONFIG_DM_SPI=y CONFIG_FSL_DSPI=y CONFIG_USB=y CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_CI_UDC=y diff --git a/configs/corvus_defconfig b/configs/corvus_defconfig index ec6d1a445d..36e6608c43 100644 --- a/configs/corvus_defconfig +++ b/configs/corvus_defconfig @@ -34,6 +34,7 @@ CONFIG_OF_EMBED=y CONFIG_DFU_NAND=y # CONFIG_MMC is not set CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_ATMEL_USBA=y diff --git a/configs/d2net_v2_defconfig b/configs/d2net_v2_defconfig index 54ace36a99..67a791d991 100644 --- a/configs/d2net_v2_defconfig +++ b/configs/d2net_v2_defconfig @@ -27,5 +27,6 @@ CONFIG_SPI_FLASH=y CONFIG_SPI_FLASH_MACRONIX=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/dalmore_defconfig b/configs/dalmore_defconfig index 8aae0e15dc..739cfa96cf 100644 --- a/configs/dalmore_defconfig +++ b/configs/dalmore_defconfig @@ -37,6 +37,7 @@ CONFIG_SYS_NS16550=y CONFIG_TEGRA114_SPI=y CONFIG_USB=y CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_CI_UDC=y diff --git a/configs/digsy_mtc_RAMBOOT_defconfig b/configs/digsy_mtc_RAMBOOT_defconfig index 0d11eec75a..86b2b0d804 100644 --- a/configs/digsy_mtc_RAMBOOT_defconfig +++ b/configs/digsy_mtc_RAMBOOT_defconfig @@ -13,7 +13,6 @@ CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n" CONFIG_AUTOBOOT_DELAY_STR="d" CONFIG_AUTOBOOT_STOP_STR=" " CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -21,7 +20,6 @@ CONFIG_CMD_MII=y CONFIG_CMD_PING=y CONFIG_CMD_BMP=y CONFIG_CMD_CACHE=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/digsy_mtc_defconfig b/configs/digsy_mtc_defconfig index dc17ab4406..85b7f850f7 100644 --- a/configs/digsy_mtc_defconfig +++ b/configs/digsy_mtc_defconfig @@ -11,7 +11,6 @@ CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="autoboot in %d seconds\n" CONFIG_AUTOBOOT_DELAY_STR=" " CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -19,7 +18,6 @@ CONFIG_CMD_MII=y CONFIG_CMD_PING=y CONFIG_CMD_BMP=y CONFIG_CMD_CACHE=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/digsy_mtc_rev5_RAMBOOT_defconfig b/configs/digsy_mtc_rev5_RAMBOOT_defconfig index 4ab11c755b..7ec8650aca 100644 --- a/configs/digsy_mtc_rev5_RAMBOOT_defconfig +++ b/configs/digsy_mtc_rev5_RAMBOOT_defconfig @@ -13,7 +13,6 @@ CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n" CONFIG_AUTOBOOT_DELAY_STR="d" CONFIG_AUTOBOOT_STOP_STR=" " CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -21,7 +20,6 @@ CONFIG_CMD_MII=y CONFIG_CMD_PING=y CONFIG_CMD_BMP=y CONFIG_CMD_CACHE=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/digsy_mtc_rev5_defconfig b/configs/digsy_mtc_rev5_defconfig index 1f3f3c8bb6..b4b8533063 100644 --- a/configs/digsy_mtc_rev5_defconfig +++ b/configs/digsy_mtc_rev5_defconfig @@ -13,7 +13,6 @@ CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n" CONFIG_AUTOBOOT_DELAY_STR="d" CONFIG_AUTOBOOT_STOP_STR=" " CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -21,7 +20,6 @@ CONFIG_CMD_MII=y CONFIG_CMD_PING=y CONFIG_CMD_BMP=y CONFIG_CMD_CACHE=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/dns325_defconfig b/configs/dns325_defconfig index a363292350..87ef896591 100644 --- a/configs/dns325_defconfig +++ b/configs/dns325_defconfig @@ -21,5 +21,6 @@ CONFIG_ISO_PARTITION=y # CONFIG_MMC is not set CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/dockstar_defconfig b/configs/dockstar_defconfig index e1ce9a5089..14eee484e0 100644 --- a/configs/dockstar_defconfig +++ b/configs/dockstar_defconfig @@ -19,5 +19,6 @@ CONFIG_ISO_PARTITION=y # CONFIG_MMC is not set CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/draco_defconfig b/configs/draco_defconfig index 2ecdd3c8f6..0e50b3109e 100644 --- a/configs/draco_defconfig +++ b/configs/draco_defconfig @@ -65,3 +65,4 @@ CONFIG_USB_GADGET_DOWNLOAD=y CONFIG_G_DNL_MANUFACTURER="Siemens AG" CONFIG_G_DNL_VENDOR_NUM=0x0908 CONFIG_G_DNL_PRODUCT_NUM=0x02d2 +CONFIG_OMAP_WATCHDOG=y diff --git a/configs/dreamplug_defconfig b/configs/dreamplug_defconfig index c8b8ce3dd0..e30ba0dace 100644 --- a/configs/dreamplug_defconfig +++ b/configs/dreamplug_defconfig @@ -23,5 +23,6 @@ CONFIG_SPI_FLASH=y CONFIG_SPI_FLASH_MACRONIX=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/ds109_defconfig b/configs/ds109_defconfig index 16f0585657..e9f67ae455 100644 --- a/configs/ds109_defconfig +++ b/configs/ds109_defconfig @@ -18,3 +18,5 @@ CONFIG_SPI_FLASH=y CONFIG_SPI_FLASH_BAR=y CONFIG_SPI_FLASH_STMICRO=y CONFIG_SYS_NS16550=y +CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y diff --git a/configs/ds414_defconfig b/configs/ds414_defconfig index c956ce04ef..b637483720 100644 --- a/configs/ds414_defconfig +++ b/configs/ds414_defconfig @@ -40,4 +40,5 @@ CONFIG_DEBUG_UART_CLOCK=250000000 CONFIG_DEBUG_UART_SHIFT=2 CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y diff --git a/configs/duovero_defconfig b/configs/duovero_defconfig index 840b3f2057..9e0ac20985 100644 --- a/configs/duovero_defconfig +++ b/configs/duovero_defconfig @@ -26,5 +26,6 @@ CONFIG_SPL_PARTITION_UUIDS=y CONFIG_MMC_OMAP_HS=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/e2220-1170_defconfig b/configs/e2220-1170_defconfig index c5563a4461..7c51cc485c 100644 --- a/configs/e2220-1170_defconfig +++ b/configs/e2220-1170_defconfig @@ -32,6 +32,7 @@ CONFIG_SYS_NS16550=y CONFIG_TEGRA114_SPI=y CONFIG_USB=y CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_CI_UDC=y diff --git a/configs/eco5pk_defconfig b/configs/eco5pk_defconfig index 2f3d814163..61ac94bbba 100644 --- a/configs/eco5pk_defconfig +++ b/configs/eco5pk_defconfig @@ -24,5 +24,7 @@ CONFIG_CMD_UBI=y CONFIG_MMC_OMAP_HS=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y +# CONFIG_USB_EHCI_OMAP is not set CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/edminiv2_defconfig b/configs/edminiv2_defconfig index cc83b68d04..51c9ba5f0e 100644 --- a/configs/edminiv2_defconfig +++ b/configs/edminiv2_defconfig @@ -21,4 +21,5 @@ CONFIG_ISO_PARTITION=y CONFIG_MTD_NOR_FLASH=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y diff --git a/configs/etamin_defconfig b/configs/etamin_defconfig index 7e0b1923b8..b6911fd717 100644 --- a/configs/etamin_defconfig +++ b/configs/etamin_defconfig @@ -65,3 +65,4 @@ CONFIG_USB_GADGET_DOWNLOAD=y CONFIG_G_DNL_MANUFACTURER="Siemens AG" CONFIG_G_DNL_VENDOR_NUM=0x0908 CONFIG_G_DNL_PRODUCT_NUM=0x02d2 +CONFIG_OMAP_WATCHDOG=y diff --git a/configs/fo300_defconfig b/configs/fo300_defconfig index b4f334a436..00418153be 100644 --- a/configs/fo300_defconfig +++ b/configs/fo300_defconfig @@ -12,7 +12,6 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -21,7 +20,6 @@ CONFIG_CMD_PING=y CONFIG_CMD_SNTP=y CONFIG_CMD_BMP=y CONFIG_CMD_BSP=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/goflexhome_defconfig b/configs/goflexhome_defconfig index dbd81331a8..046435a995 100644 --- a/configs/goflexhome_defconfig +++ b/configs/goflexhome_defconfig @@ -22,5 +22,6 @@ CONFIG_ISO_PARTITION=y # CONFIG_MMC is not set CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/gose_defconfig b/configs/gose_defconfig index 761d75896d..5627a18631 100644 --- a/configs/gose_defconfig +++ b/configs/gose_defconfig @@ -25,4 +25,5 @@ CONFIG_SPI_FLASH_BAR=y CONFIG_SPI_FLASH_SPANSION=y CONFIG_BAUDRATE=38400 CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y diff --git a/configs/gplugd_defconfig b/configs/gplugd_defconfig index 97bb976803..75e980979c 100644 --- a/configs/gplugd_defconfig +++ b/configs/gplugd_defconfig @@ -6,7 +6,6 @@ CONFIG_BOOTDELAY=3 CONFIG_BOARD_EARLY_INIT_F=y # CONFIG_CMD_IMLS is not set # CONFIG_CMD_FLASH is not set -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_FPGA is not set # CONFIG_CMD_SETEXPR is not set @@ -19,5 +18,6 @@ CONFIG_ISO_PARTITION=y # CONFIG_MMC is not set CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/gurnard_defconfig b/configs/gurnard_defconfig index 7d91fad27e..2c6f52494a 100644 --- a/configs/gurnard_defconfig +++ b/configs/gurnard_defconfig @@ -20,6 +20,7 @@ CONFIG_CMD_GPIO=y # CONFIG_CMD_SETEXPR is not set CONFIG_OF_CONTROL=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_DM_VIDEO=y CONFIG_CMD_DHRYSTONE=y diff --git a/configs/guruplug_defconfig b/configs/guruplug_defconfig index c09d3a61e1..f2c22bfd54 100644 --- a/configs/guruplug_defconfig +++ b/configs/guruplug_defconfig @@ -23,5 +23,6 @@ CONFIG_ISO_PARTITION=y # CONFIG_MMC is not set CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/harmony_defconfig b/configs/harmony_defconfig index 6163353621..e9b8ac26a6 100644 --- a/configs/harmony_defconfig +++ b/configs/harmony_defconfig @@ -34,6 +34,7 @@ CONFIG_PWM_TEGRA=y CONFIG_SYS_NS16550=y CONFIG_USB=y CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_ULPI_VIEWPORT=y CONFIG_USB_ULPI=y CONFIG_USB_STORAGE=y diff --git a/configs/ib62x0_defconfig b/configs/ib62x0_defconfig index 2e08690981..f454277678 100644 --- a/configs/ib62x0_defconfig +++ b/configs/ib62x0_defconfig @@ -22,5 +22,6 @@ CONFIG_ISO_PARTITION=y # CONFIG_MMC is not set CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/iconnect_defconfig b/configs/iconnect_defconfig index 409c836fd6..7e0b444b54 100644 --- a/configs/iconnect_defconfig +++ b/configs/iconnect_defconfig @@ -18,5 +18,6 @@ CONFIG_ISO_PARTITION=y # CONFIG_MMC is not set CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/inetspace_v2_defconfig b/configs/inetspace_v2_defconfig index 0f115066db..bee04903fe 100644 --- a/configs/inetspace_v2_defconfig +++ b/configs/inetspace_v2_defconfig @@ -27,5 +27,6 @@ CONFIG_SPI_FLASH=y CONFIG_SPI_FLASH_MACRONIX=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/ipek01_defconfig b/configs/ipek01_defconfig index cac9326b6c..690bc0f461 100644 --- a/configs/ipek01_defconfig +++ b/configs/ipek01_defconfig @@ -7,13 +7,11 @@ CONFIG_BOOTDELAY=5 # CONFIG_CONSOLE_MUX is not set CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_BMP=y -CONFIG_CMD_DATE=y CONFIG_CMD_FAT=y # CONFIG_MMC is not set CONFIG_MTD_NOR_FLASH=y diff --git a/configs/jetson-tk1_defconfig b/configs/jetson-tk1_defconfig index 2c3f1748d8..982aec48e7 100644 --- a/configs/jetson-tk1_defconfig +++ b/configs/jetson-tk1_defconfig @@ -43,6 +43,7 @@ CONFIG_SYS_NS16550=y CONFIG_TEGRA114_SPI=y CONFIG_USB=y CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_CI_UDC=y diff --git a/configs/koelsch_defconfig b/configs/koelsch_defconfig index e6b1684408..465a6be8e7 100644 --- a/configs/koelsch_defconfig +++ b/configs/koelsch_defconfig @@ -25,4 +25,5 @@ CONFIG_SPI_FLASH_BAR=y CONFIG_SPI_FLASH_SPANSION=y CONFIG_BAUDRATE=38400 CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y diff --git a/configs/lager_defconfig b/configs/lager_defconfig index a123b37546..c2f216bd51 100644 --- a/configs/lager_defconfig +++ b/configs/lager_defconfig @@ -25,4 +25,5 @@ CONFIG_SPI_FLASH_BAR=y CONFIG_SPI_FLASH_SPANSION=y CONFIG_BAUDRATE=38400 CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y diff --git a/configs/liteboard_defconfig b/configs/liteboard_defconfig index f09647132d..e550cf250a 100644 --- a/configs/liteboard_defconfig +++ b/configs/liteboard_defconfig @@ -27,4 +27,5 @@ CONFIG_CMD_EXT4=y CONFIG_CMD_EXT4_WRITE=y CONFIG_CMD_FAT=y CONFIG_CMD_FS_GENERIC=y +CONFIG_USB=y CONFIG_OF_LIBFDT=y diff --git a/configs/lschlv2_defconfig b/configs/lschlv2_defconfig index 8804149fc3..124bf24c4b 100644 --- a/configs/lschlv2_defconfig +++ b/configs/lschlv2_defconfig @@ -30,5 +30,6 @@ CONFIG_SPI_FLASH=y CONFIG_SPI_FLASH_STMICRO=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/lsxhl_defconfig b/configs/lsxhl_defconfig index 918d2e973f..398c6b59ec 100644 --- a/configs/lsxhl_defconfig +++ b/configs/lsxhl_defconfig @@ -21,5 +21,6 @@ CONFIG_SPI_FLASH=y CONFIG_SPI_FLASH_STMICRO=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/lwmon5_defconfig b/configs/lwmon5_defconfig index 429a81f6b7..5fc5916124 100644 --- a/configs/lwmon5_defconfig +++ b/configs/lwmon5_defconfig @@ -31,6 +31,7 @@ CONFIG_MTD_NOR_FLASH=y # CONFIG_PCI is not set CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_CONSOLE_EXTRA_INFO=y CONFIG_OF_LIBFDT=y diff --git a/configs/m28evk_defconfig b/configs/m28evk_defconfig index 6acbd77d5f..fbd106ef92 100644 --- a/configs/m28evk_defconfig +++ b/configs/m28evk_defconfig @@ -22,7 +22,6 @@ CONFIG_CMD_GREPENV=y CONFIG_CMD_MMC=y CONFIG_CMD_SF=y CONFIG_CMD_SPI=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y CONFIG_CMD_GPIO=y CONFIG_CMD_DHCP=y @@ -40,5 +39,6 @@ CONFIG_MMC_MXS=y CONFIG_SPI_FLASH=y CONFIG_SPI_FLASH_STMICRO=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/ma5d4evk_defconfig b/configs/ma5d4evk_defconfig index adeab1a0e9..a267c9a55f 100644 --- a/configs/ma5d4evk_defconfig +++ b/configs/ma5d4evk_defconfig @@ -36,6 +36,7 @@ CONFIG_CMD_FAT=y CONFIG_CMD_FS_GENERIC=y CONFIG_SPI_FLASH=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_ATMEL_USBA=y diff --git a/configs/mccmon6_nor_defconfig b/configs/mccmon6_nor_defconfig index 77a4035384..7744fcb535 100644 --- a/configs/mccmon6_nor_defconfig +++ b/configs/mccmon6_nor_defconfig @@ -32,4 +32,5 @@ CONFIG_MTD_NOR_FLASH=y CONFIG_SPI_FLASH=y CONFIG_SPI_FLASH_SPANSION=y CONFIG_DM_THERMAL=y +CONFIG_USB=y CONFIG_OF_LIBFDT=y diff --git a/configs/mccmon6_sd_defconfig b/configs/mccmon6_sd_defconfig index 332eddfa38..1118caa0a9 100644 --- a/configs/mccmon6_sd_defconfig +++ b/configs/mccmon6_sd_defconfig @@ -33,4 +33,5 @@ CONFIG_MTD_NOR_FLASH=y CONFIG_SPI_FLASH=y CONFIG_SPI_FLASH_SPANSION=y CONFIG_DM_THERMAL=y +CONFIG_USB=y CONFIG_OF_LIBFDT=y diff --git a/configs/mcx_defconfig b/configs/mcx_defconfig index 3cc1a2ba14..349df80f05 100644 --- a/configs/mcx_defconfig +++ b/configs/mcx_defconfig @@ -33,6 +33,7 @@ CONFIG_CMD_UBI=y CONFIG_MMC_OMAP_HS=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_ULPI_VIEWPORT_OMAP=y CONFIG_USB_ULPI=y CONFIG_USB_STORAGE=y diff --git a/configs/mecp5123_defconfig b/configs/mecp5123_defconfig index ebf5415464..db52077e1a 100644 --- a/configs/mecp5123_defconfig +++ b/configs/mecp5123_defconfig @@ -6,12 +6,10 @@ CONFIG_BOOTDELAY=5 CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_PING=y -CONFIG_CMD_DATE=y CONFIG_CMD_FAT=y # CONFIG_MMC is not set CONFIG_MTD_NOR_FLASH=y diff --git a/configs/medcom-wide_defconfig b/configs/medcom-wide_defconfig index a811506f29..e30ac758dd 100644 --- a/configs/medcom-wide_defconfig +++ b/configs/medcom-wide_defconfig @@ -32,6 +32,7 @@ CONFIG_PWM_TEGRA=y CONFIG_SYS_NS16550=y CONFIG_USB=y CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_DM_VIDEO=y CONFIG_VIDEO_TEGRA20=y diff --git a/configs/motionpro_defconfig b/configs/motionpro_defconfig index 91384a6259..5040ea5742 100644 --- a/configs/motionpro_defconfig +++ b/configs/motionpro_defconfig @@ -8,12 +8,10 @@ CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press \"<Esc><Esc>\" to stop\n" CONFIG_AUTOBOOT_STOP_STR="\x1b\x1b" CONFIG_CMD_ASKENV=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_PING=y -CONFIG_CMD_DATE=y CONFIG_CMD_FAT=y CONFIG_CMD_BEDBUG=y CONFIG_LED_STATUS=y diff --git a/configs/mpc5121ads_defconfig b/configs/mpc5121ads_defconfig index c0af8127b5..a6bfc71f5e 100644 --- a/configs/mpc5121ads_defconfig +++ b/configs/mpc5121ads_defconfig @@ -6,13 +6,11 @@ CONFIG_BOOTDELAY=5 CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_PING=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_MAC_PARTITION=y @@ -20,5 +18,6 @@ CONFIG_ISO_PARTITION=y # CONFIG_MMC is not set CONFIG_MTD_NOR_FLASH=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/mpc5121ads_rev2_defconfig b/configs/mpc5121ads_rev2_defconfig index ad46e02e94..61c366a294 100644 --- a/configs/mpc5121ads_rev2_defconfig +++ b/configs/mpc5121ads_rev2_defconfig @@ -7,13 +7,11 @@ CONFIG_BOOTDELAY=5 CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_PING=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_MAC_PARTITION=y @@ -22,5 +20,6 @@ CONFIG_ISO_PARTITION=y CONFIG_MTD_NOR_FLASH=y # CONFIG_PCI is not set CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/mt_ventoux_defconfig b/configs/mt_ventoux_defconfig index 08e400cc4e..484086837a 100644 --- a/configs/mt_ventoux_defconfig +++ b/configs/mt_ventoux_defconfig @@ -29,6 +29,7 @@ CONFIG_CMD_UBI=y CONFIG_MMC_OMAP_HS=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_ULPI_VIEWPORT_OMAP=y CONFIG_USB_ULPI=y CONFIG_USB_STORAGE=y diff --git a/configs/mx23_olinuxino_defconfig b/configs/mx23_olinuxino_defconfig index feaa0876ef..795de14740 100644 --- a/configs/mx23_olinuxino_defconfig +++ b/configs/mx23_olinuxino_defconfig @@ -30,5 +30,6 @@ CONFIG_LED_STATUS_BOOT=0 CONFIG_LED_STATUS_CMD=y CONFIG_MMC_MXS=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/mx23evk_defconfig b/configs/mx23evk_defconfig index 2e71dd9742..7eb1791d6c 100644 --- a/configs/mx23evk_defconfig +++ b/configs/mx23evk_defconfig @@ -28,5 +28,6 @@ CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_MMC_MXS=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/mx28evk_auart_console_defconfig b/configs/mx28evk_auart_console_defconfig index d7a1d684c8..710ae4711d 100644 --- a/configs/mx28evk_auart_console_defconfig +++ b/configs/mx28evk_auart_console_defconfig @@ -37,5 +37,6 @@ CONFIG_MMC_MXS=y CONFIG_SPI_FLASH=y CONFIG_SPI_FLASH_SST=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/mx28evk_defconfig b/configs/mx28evk_defconfig index c5fe5595bc..95ac31adaf 100644 --- a/configs/mx28evk_defconfig +++ b/configs/mx28evk_defconfig @@ -38,5 +38,6 @@ CONFIG_MMC_MXS=y CONFIG_SPI_FLASH=y CONFIG_SPI_FLASH_SST=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/mx28evk_nand_defconfig b/configs/mx28evk_nand_defconfig index f878bafa00..3b955401ca 100644 --- a/configs/mx28evk_nand_defconfig +++ b/configs/mx28evk_nand_defconfig @@ -37,5 +37,6 @@ CONFIG_MMC_MXS=y CONFIG_SPI_FLASH=y CONFIG_SPI_FLASH_SST=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/mx28evk_spi_defconfig b/configs/mx28evk_spi_defconfig index 5203349c7a..1b5de66553 100644 --- a/configs/mx28evk_spi_defconfig +++ b/configs/mx28evk_spi_defconfig @@ -37,5 +37,6 @@ CONFIG_MMC_MXS=y CONFIG_SPI_FLASH=y CONFIG_SPI_FLASH_SST=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/mx35pdk_defconfig b/configs/mx35pdk_defconfig index 655a1a5224..0da348adff 100644 --- a/configs/mx35pdk_defconfig +++ b/configs/mx35pdk_defconfig @@ -21,5 +21,6 @@ CONFIG_EFI_PARTITION=y # CONFIG_PARTITION_UUIDS is not set CONFIG_MTD_NOR_FLASH=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/mx6sllevk_defconfig b/configs/mx6sllevk_defconfig index a87dec8e3a..949ce91804 100644 --- a/configs/mx6sllevk_defconfig +++ b/configs/mx6sllevk_defconfig @@ -39,5 +39,4 @@ CONFIG_DM_REGULATOR_FIXED=y CONFIG_DM_REGULATOR_GPIO=y CONFIG_USB=y CONFIG_DM_USB=y -CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y diff --git a/configs/mx6sllevk_plugin_defconfig b/configs/mx6sllevk_plugin_defconfig index 41ecf92322..60a4431083 100644 --- a/configs/mx6sllevk_plugin_defconfig +++ b/configs/mx6sllevk_plugin_defconfig @@ -40,5 +40,4 @@ CONFIG_DM_REGULATOR_FIXED=y CONFIG_DM_REGULATOR_GPIO=y CONFIG_USB=y CONFIG_DM_USB=y -CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y diff --git a/configs/nas220_defconfig b/configs/nas220_defconfig index 7a02538301..8e9c13a37c 100644 --- a/configs/nas220_defconfig +++ b/configs/nas220_defconfig @@ -24,5 +24,6 @@ CONFIG_EFI_PARTITION=y # CONFIG_MMC is not set CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/net2big_v2_defconfig b/configs/net2big_v2_defconfig index 5e41e02a02..b43ad161f8 100644 --- a/configs/net2big_v2_defconfig +++ b/configs/net2big_v2_defconfig @@ -27,5 +27,6 @@ CONFIG_SPI_FLASH=y CONFIG_SPI_FLASH_MACRONIX=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/netspace_lite_v2_defconfig b/configs/netspace_lite_v2_defconfig index 2d04fb5979..3c3fc99e94 100644 --- a/configs/netspace_lite_v2_defconfig +++ b/configs/netspace_lite_v2_defconfig @@ -27,5 +27,6 @@ CONFIG_SPI_FLASH=y CONFIG_SPI_FLASH_MACRONIX=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/netspace_max_v2_defconfig b/configs/netspace_max_v2_defconfig index 6c730fc7d8..4605be3cd2 100644 --- a/configs/netspace_max_v2_defconfig +++ b/configs/netspace_max_v2_defconfig @@ -27,5 +27,6 @@ CONFIG_SPI_FLASH=y CONFIG_SPI_FLASH_MACRONIX=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/netspace_v2_defconfig b/configs/netspace_v2_defconfig index 4b3c851842..2103a1c8db 100644 --- a/configs/netspace_v2_defconfig +++ b/configs/netspace_v2_defconfig @@ -27,5 +27,6 @@ CONFIG_SPI_FLASH=y CONFIG_SPI_FLASH_MACRONIX=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/nsa310s_defconfig b/configs/nsa310s_defconfig index 4a0f9455cb..3269b85e88 100644 --- a/configs/nsa310s_defconfig +++ b/configs/nsa310s_defconfig @@ -21,5 +21,6 @@ CONFIG_ISO_PARTITION=y # CONFIG_MMC is not set CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/nyan-big_defconfig b/configs/nyan-big_defconfig index 42fe120786..c01d5f5285 100644 --- a/configs/nyan-big_defconfig +++ b/configs/nyan-big_defconfig @@ -52,6 +52,7 @@ CONFIG_TEGRA114_SPI=y CONFIG_TPM_TIS_INFINEON=y CONFIG_USB=y CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_CI_UDC=y diff --git a/configs/odroid-xu3_defconfig b/configs/odroid-xu3_defconfig index dab4cc1443..fed24ec90d 100644 --- a/configs/odroid-xu3_defconfig +++ b/configs/odroid-xu3_defconfig @@ -36,6 +36,7 @@ CONFIG_USB=y CONFIG_DM_USB=y CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_DWC3=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_DWC3=y CONFIG_USB_DWC3_GADGET=y CONFIG_USB_DWC3_PHY_SAMSUNG=y diff --git a/configs/odroid_defconfig b/configs/odroid_defconfig index a28058ad6a..f4e9e9af5b 100644 --- a/configs/odroid_defconfig +++ b/configs/odroid_defconfig @@ -49,6 +49,7 @@ CONFIG_DM_REGULATOR=y CONFIG_DM_REGULATOR_MAX77686=y CONFIG_USB=y CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_DWC2_OTG=y diff --git a/configs/omap3_beagle_defconfig b/configs/omap3_beagle_defconfig index 46846b2ccc..64971c139c 100644 --- a/configs/omap3_beagle_defconfig +++ b/configs/omap3_beagle_defconfig @@ -34,6 +34,7 @@ CONFIG_LED_STATUS_CMD=y CONFIG_MMC_OMAP_HS=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_MUSB_GADGET=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y diff --git a/configs/omap3_ha_defconfig b/configs/omap3_ha_defconfig index 911021b747..6194a66ce7 100644 --- a/configs/omap3_ha_defconfig +++ b/configs/omap3_ha_defconfig @@ -24,5 +24,6 @@ CONFIG_CMD_FAT=y CONFIG_MMC_OMAP_HS=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/omap3_logic_defconfig b/configs/omap3_logic_defconfig index 561bdfbceb..50450c9653 100644 --- a/configs/omap3_logic_defconfig +++ b/configs/omap3_logic_defconfig @@ -1,11 +1,11 @@ CONFIG_ARM=y CONFIG_ARCH_OMAP2PLUS=y +CONFIG_TI_COMMON_CMD_OPTIONS=y CONFIG_SYS_MALLOC_F_LEN=0x2000 CONFIG_OMAP34XX=y CONFIG_TARGET_OMAP3_LOGIC=y CONFIG_SPL_STACK_R_ADDR=0x82000000 CONFIG_DEFAULT_DEVICE_TREE="logicpd-torpedo-37xx-devkit" -CONFIG_FIT=y CONFIG_SYS_EXTRA_OPTIONS="NAND" CONFIG_SYS_CONSOLE_INFO_QUIET=y CONFIG_VERSION_VARIABLE=y @@ -16,29 +16,14 @@ CONFIG_SPL_MTD_SUPPORT=y CONFIG_SPL_OS_BOOT=y CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="OMAP Logic # " -CONFIG_CMD_BOOTZ=y # CONFIG_CMD_IMI is not set # CONFIG_CMD_IMLS is not set -CONFIG_CMD_ASKENV=y # CONFIG_CMD_FLASH is not set -CONFIG_CMD_MMC=y -CONFIG_CMD_PART=y -CONFIG_CMD_SPI=y -CONFIG_CMD_I2C=y +# CONFIG_CMD_USB is not set # CONFIG_CMD_FPGA is not set -CONFIG_CMD_GPIO=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y CONFIG_CMD_CACHE=y -CONFIG_CMD_EXT2=y -CONFIG_CMD_EXT4=y -CONFIG_CMD_EXT4_WRITE=y -CONFIG_CMD_FAT=y -CONFIG_CMD_FS_GENERIC=y CONFIG_CMD_UBI=y CONFIG_ISO_PARTITION=y -CONFIG_EFI_PARTITION=y CONFIG_OF_CONTROL=y # CONFIG_BLK is not set CONFIG_DM_I2C=y diff --git a/configs/omap3_overo_defconfig b/configs/omap3_overo_defconfig index daea034ba9..3be4a1d0b3 100644 --- a/configs/omap3_overo_defconfig +++ b/configs/omap3_overo_defconfig @@ -42,5 +42,6 @@ CONFIG_EFI_PARTITION=y CONFIG_MMC_OMAP_HS=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/omap4_panda_defconfig b/configs/omap4_panda_defconfig index af459fcfde..8fdf76076c 100644 --- a/configs/omap4_panda_defconfig +++ b/configs/omap4_panda_defconfig @@ -25,5 +25,6 @@ CONFIG_CMD_EXT4_WRITE=y CONFIG_MMC_OMAP_HS=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/omap5_uevm_defconfig b/configs/omap5_uevm_defconfig index 865845ee9c..bd799b7dc3 100644 --- a/configs/omap5_uevm_defconfig +++ b/configs/omap5_uevm_defconfig @@ -2,6 +2,7 @@ CONFIG_ARM=y CONFIG_ARCH_OMAP2PLUS=y CONFIG_OMAP54XX=y CONFIG_TARGET_OMAP5_UEVM=y +CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC=16296 # CONFIG_SPL_NAND_SUPPORT is not set CONFIG_ARMV7_LPAE=y CONFIG_SYS_CONSOLE_INFO_QUIET=y @@ -36,6 +37,7 @@ CONFIG_DFU_RAM=y CONFIG_MMC_OMAP_HS=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_DWC3=y CONFIG_USB_DWC3_GADGET=y CONFIG_USB_DWC3_OMAP=y diff --git a/configs/omapl138_lcdk_defconfig b/configs/omapl138_lcdk_defconfig index 752ff5d860..0629f9636f 100644 --- a/configs/omapl138_lcdk_defconfig +++ b/configs/omapl138_lcdk_defconfig @@ -15,7 +15,6 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_SPL=y CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0xb5 CONFIG_HUSH_PARSER=y -CONFIG_SYS_PROMPT="U-Boot > " # CONFIG_CMD_IMLS is not set # CONFIG_CMD_FLASH is not set # CONFIG_CMD_GPIO is not set diff --git a/configs/openrd_base_defconfig b/configs/openrd_base_defconfig index 2abf3ab6a1..84d3f89850 100644 --- a/configs/openrd_base_defconfig +++ b/configs/openrd_base_defconfig @@ -20,5 +20,6 @@ CONFIG_CMD_UBI=y CONFIG_ISO_PARTITION=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/openrd_client_defconfig b/configs/openrd_client_defconfig index 8b3f25fd95..57cbb3a0b9 100644 --- a/configs/openrd_client_defconfig +++ b/configs/openrd_client_defconfig @@ -20,5 +20,6 @@ CONFIG_CMD_UBI=y CONFIG_ISO_PARTITION=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/openrd_ultimate_defconfig b/configs/openrd_ultimate_defconfig index ba774738fc..4bc2dcee4e 100644 --- a/configs/openrd_ultimate_defconfig +++ b/configs/openrd_ultimate_defconfig @@ -20,5 +20,6 @@ CONFIG_CMD_UBI=y CONFIG_ISO_PARTITION=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/opos6uldev_defconfig b/configs/opos6uldev_defconfig index 4f8f659321..1a9d6cddc3 100644 --- a/configs/opos6uldev_defconfig +++ b/configs/opos6uldev_defconfig @@ -75,7 +75,6 @@ CONFIG_MXC_UART=y CONFIG_IMX_THERMAL=y CONFIG_USB=y CONFIG_DM_USB=y -CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_CI_UDC=y diff --git a/configs/p2371-0000_defconfig b/configs/p2371-0000_defconfig index 0ff4c13aa0..d78f4450e8 100644 --- a/configs/p2371-0000_defconfig +++ b/configs/p2371-0000_defconfig @@ -33,6 +33,7 @@ CONFIG_SYS_NS16550=y CONFIG_TEGRA114_SPI=y CONFIG_USB=y CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_CI_UDC=y diff --git a/configs/p2371-2180_defconfig b/configs/p2371-2180_defconfig index 4dfb02db20..e409a3909b 100644 --- a/configs/p2371-2180_defconfig +++ b/configs/p2371-2180_defconfig @@ -38,6 +38,7 @@ CONFIG_SYS_NS16550=y CONFIG_TEGRA114_SPI=y CONFIG_USB=y CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_CI_UDC=y diff --git a/configs/p2571_defconfig b/configs/p2571_defconfig index e49a42f45b..daf9165659 100644 --- a/configs/p2571_defconfig +++ b/configs/p2571_defconfig @@ -33,6 +33,7 @@ CONFIG_SYS_NS16550=y CONFIG_TEGRA114_SPI=y CONFIG_USB=y CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_CI_UDC=y diff --git a/configs/paz00_defconfig b/configs/paz00_defconfig index 0ad0974d34..9386df83a8 100644 --- a/configs/paz00_defconfig +++ b/configs/paz00_defconfig @@ -31,6 +31,7 @@ CONFIG_PWM_TEGRA=y CONFIG_SYS_NS16550=y CONFIG_USB=y CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_DM_VIDEO=y CONFIG_VIDEO_TEGRA20=y diff --git a/configs/pcm030_LOWBOOT_defconfig b/configs/pcm030_LOWBOOT_defconfig index d19908ca8f..2933326e5d 100644 --- a/configs/pcm030_LOWBOOT_defconfig +++ b/configs/pcm030_LOWBOOT_defconfig @@ -4,11 +4,9 @@ CONFIG_TARGET_PCM030=y CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_EXTRA_OPTIONS="SYS_TEXT_BASE=0xFF000000" CONFIG_BOOTDELAY=3 -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y -CONFIG_CMD_DATE=y # CONFIG_MMC is not set CONFIG_MTD_NOR_FLASH=y CONFIG_USB=y diff --git a/configs/pcm030_defconfig b/configs/pcm030_defconfig index ef5c85888c..ff9f4e9f4f 100644 --- a/configs/pcm030_defconfig +++ b/configs/pcm030_defconfig @@ -4,11 +4,9 @@ CONFIG_TARGET_PCM030=y CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=3 CONFIG_SYS_PROMPT="uboot> " -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y -CONFIG_CMD_DATE=y # CONFIG_MMC is not set CONFIG_MTD_NOR_FLASH=y CONFIG_USB=y diff --git a/configs/pdm360ng_defconfig b/configs/pdm360ng_defconfig index f45a90caf9..4ef0df1aa8 100644 --- a/configs/pdm360ng_defconfig +++ b/configs/pdm360ng_defconfig @@ -10,13 +10,11 @@ CONFIG_SILENT_CONSOLE=y # CONFIG_CONSOLE_MUX is not set CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_PING=y CONFIG_CMD_BMP=y -CONFIG_CMD_DATE=y # CONFIG_MMC is not set CONFIG_MTD_NOR_FLASH=y # CONFIG_PCI is not set diff --git a/configs/picosam9g45_defconfig b/configs/picosam9g45_defconfig index ab4415e522..f34dfe9fdb 100644 --- a/configs/picosam9g45_defconfig +++ b/configs/picosam9g45_defconfig @@ -32,6 +32,7 @@ CONFIG_CMD_DHCP=y CONFIG_CMD_PING=y CONFIG_CMD_FAT=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_LCD=y CONFIG_OF_LIBFDT=y diff --git a/configs/plutux_defconfig b/configs/plutux_defconfig index 0c6c65e9d8..f0fdde713a 100644 --- a/configs/plutux_defconfig +++ b/configs/plutux_defconfig @@ -27,4 +27,5 @@ CONFIG_SPL_DM=y CONFIG_SYS_NS16550=y CONFIG_USB=y CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y diff --git a/configs/pogo_e02_defconfig b/configs/pogo_e02_defconfig index 029ecc8dc8..7699e0c5e6 100644 --- a/configs/pogo_e02_defconfig +++ b/configs/pogo_e02_defconfig @@ -19,5 +19,6 @@ CONFIG_ISO_PARTITION=y # CONFIG_MMC is not set CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/porter_defconfig b/configs/porter_defconfig index 206ba472fa..a50d9ed99b 100644 --- a/configs/porter_defconfig +++ b/configs/porter_defconfig @@ -25,4 +25,5 @@ CONFIG_SPI_FLASH_BAR=y CONFIG_SPI_FLASH_SPANSION=y CONFIG_BAUDRATE=38400 CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y diff --git a/configs/pxm2_defconfig b/configs/pxm2_defconfig index c40684a81d..67bdfd63f2 100644 --- a/configs/pxm2_defconfig +++ b/configs/pxm2_defconfig @@ -72,3 +72,4 @@ CONFIG_G_DNL_PRODUCT_NUM=0x02d2 # CONFIG_VIDEO_SW_CURSOR is not set CONFIG_SYS_CONSOLE_BG_COL=0xff CONFIG_SYS_CONSOLE_FG_COL=0x00 +CONFIG_OMAP_WATCHDOG=y diff --git a/configs/r0p7734_defconfig b/configs/r0p7734_defconfig index c5c3d52718..91b08dc24f 100644 --- a/configs/r0p7734_defconfig +++ b/configs/r0p7734_defconfig @@ -13,7 +13,6 @@ CONFIG_VERSION_VARIABLE=y # CONFIG_CMD_ENV_EXISTS is not set # CONFIG_CMD_LOADB is not set # CONFIG_CMD_LOADS is not set -CONFIG_CMD_I2C=y # CONFIG_CMD_FPGA is not set # CONFIG_CMD_ECHO is not set # CONFIG_CMD_ITEST is not set diff --git a/configs/rastaban_defconfig b/configs/rastaban_defconfig index 01848c5702..f77d4d4087 100644 --- a/configs/rastaban_defconfig +++ b/configs/rastaban_defconfig @@ -65,3 +65,4 @@ CONFIG_USB_GADGET_DOWNLOAD=y CONFIG_G_DNL_MANUFACTURER="Siemens AG" CONFIG_G_DNL_VENDOR_NUM=0x0908 CONFIG_G_DNL_PRODUCT_NUM=0x02d2 +CONFIG_OMAP_WATCHDOG=y diff --git a/configs/sama5d2_ptc_nandflash_defconfig b/configs/sama5d2_ptc_nandflash_defconfig index 9694632d2c..239bfdd66b 100644 --- a/configs/sama5d2_ptc_nandflash_defconfig +++ b/configs/sama5d2_ptc_nandflash_defconfig @@ -19,4 +19,5 @@ CONFIG_CMD_SF=y # CONFIG_MMC is not set CONFIG_SPI_FLASH=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y diff --git a/configs/sama5d2_ptc_spiflash_defconfig b/configs/sama5d2_ptc_spiflash_defconfig index 30e8500edf..21014b937c 100644 --- a/configs/sama5d2_ptc_spiflash_defconfig +++ b/configs/sama5d2_ptc_spiflash_defconfig @@ -20,4 +20,5 @@ CONFIG_CMD_SF=y # CONFIG_MMC is not set CONFIG_SPI_FLASH=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y diff --git a/configs/sansa_fuze_plus_defconfig b/configs/sansa_fuze_plus_defconfig index ff5a0823d4..80531fe6d4 100644 --- a/configs/sansa_fuze_plus_defconfig +++ b/configs/sansa_fuze_plus_defconfig @@ -27,6 +27,7 @@ CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_MMC_MXS=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_GADGET=y CONFIG_CI_UDC=y CONFIG_OF_LIBFDT=y diff --git a/configs/sc_sps_1_defconfig b/configs/sc_sps_1_defconfig index e2a8e3c762..827f4eeccb 100644 --- a/configs/sc_sps_1_defconfig +++ b/configs/sc_sps_1_defconfig @@ -24,5 +24,6 @@ CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_MMC_MXS=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/seaboard_defconfig b/configs/seaboard_defconfig index 9e50f702bf..00fc117f4a 100644 --- a/configs/seaboard_defconfig +++ b/configs/seaboard_defconfig @@ -31,6 +31,7 @@ CONFIG_PWM_TEGRA=y CONFIG_SYS_NS16550=y CONFIG_USB=y CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_ULPI_VIEWPORT=y CONFIG_USB_ULPI=y CONFIG_USB_STORAGE=y diff --git a/configs/sheevaplug_defconfig b/configs/sheevaplug_defconfig index b3280557ca..fa99d51505 100644 --- a/configs/sheevaplug_defconfig +++ b/configs/sheevaplug_defconfig @@ -23,5 +23,6 @@ CONFIG_CMD_UBI=y CONFIG_ISO_PARTITION=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/silk_defconfig b/configs/silk_defconfig index 293b08eaba..d161c3bb88 100644 --- a/configs/silk_defconfig +++ b/configs/silk_defconfig @@ -25,4 +25,5 @@ CONFIG_SPI_FLASH_BAR=y CONFIG_SPI_FLASH_SPANSION=y CONFIG_BAUDRATE=38400 CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y diff --git a/configs/smdk5250_defconfig b/configs/smdk5250_defconfig index ff52a3757a..c51df50678 100644 --- a/configs/smdk5250_defconfig +++ b/configs/smdk5250_defconfig @@ -48,6 +48,7 @@ CONFIG_USB=y CONFIG_DM_USB=y CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_DWC3=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_VIDEO_BRIDGE=y CONFIG_ERRNO_STR=y diff --git a/configs/snow_defconfig b/configs/snow_defconfig index 0ea2393bf6..8050f24fbb 100644 --- a/configs/snow_defconfig +++ b/configs/snow_defconfig @@ -66,6 +66,7 @@ CONFIG_USB=y CONFIG_DM_USB=y CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_DWC3=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_DM_VIDEO=y CONFIG_VIDCONSOLE_AS_LCD=y diff --git a/configs/socrates_defconfig b/configs/socrates_defconfig index 9e00d65034..07114ecba4 100644 --- a/configs/socrates_defconfig +++ b/configs/socrates_defconfig @@ -24,6 +24,7 @@ CONFIG_CMD_EXT2=y CONFIG_MTD_NOR_FLASH=y CONFIG_SYS_NS16550=y CONFIG_USB=y +# CONFIG_USB_EHCI_HCD is not set CONFIG_USB_STORAGE=y CONFIG_CONSOLE_EXTRA_INFO=y CONFIG_OF_LIBFDT=y diff --git a/configs/spring_defconfig b/configs/spring_defconfig index d9fd8ca362..716f8c00e6 100644 --- a/configs/spring_defconfig +++ b/configs/spring_defconfig @@ -66,6 +66,7 @@ CONFIG_USB=y CONFIG_DM_USB=y CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_DWC3=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_DM_VIDEO=y CONFIG_VIDCONSOLE_AS_LCD=y diff --git a/configs/stout_defconfig b/configs/stout_defconfig index aaa85022ed..48989aaea6 100644 --- a/configs/stout_defconfig +++ b/configs/stout_defconfig @@ -25,4 +25,5 @@ CONFIG_SPI_FLASH_BAR=y CONFIG_SPI_FLASH_SPANSION=y CONFIG_BAUDRATE=38400 CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y diff --git a/configs/tao3530_defconfig b/configs/tao3530_defconfig index 24244134c7..feb8fe690f 100644 --- a/configs/tao3530_defconfig +++ b/configs/tao3530_defconfig @@ -24,5 +24,6 @@ CONFIG_CMD_FAT=y CONFIG_MMC_OMAP_HS=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT=y diff --git a/configs/tec-ng_defconfig b/configs/tec-ng_defconfig index cd9b507803..91fd3d5f9f 100644 --- a/configs/tec-ng_defconfig +++ b/configs/tec-ng_defconfig @@ -33,4 +33,5 @@ CONFIG_SYS_NS16550=y CONFIG_TEGRA20_SLINK=y CONFIG_USB=y CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y diff --git a/configs/tec_defconfig b/configs/tec_defconfig index 1dd8a1ec20..5c394b73f5 100644 --- a/configs/tec_defconfig +++ b/configs/tec_defconfig @@ -32,6 +32,7 @@ CONFIG_PWM_TEGRA=y CONFIG_SYS_NS16550=y CONFIG_USB=y CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_DM_VIDEO=y CONFIG_VIDEO_TEGRA20=y diff --git a/configs/thuban_defconfig b/configs/thuban_defconfig index dd61ead647..914f70fd6a 100644 --- a/configs/thuban_defconfig +++ b/configs/thuban_defconfig @@ -65,3 +65,4 @@ CONFIG_USB_GADGET_DOWNLOAD=y CONFIG_G_DNL_MANUFACTURER="Siemens AG" CONFIG_G_DNL_VENDOR_NUM=0x0908 CONFIG_G_DNL_PRODUCT_NUM=0x02d2 +CONFIG_OMAP_WATCHDOG=y diff --git a/configs/trimslice_defconfig b/configs/trimslice_defconfig index 455f4b2819..e4074a0bd7 100644 --- a/configs/trimslice_defconfig +++ b/configs/trimslice_defconfig @@ -37,4 +37,5 @@ CONFIG_SYS_NS16550=y CONFIG_TEGRA20_SFLASH=y CONFIG_USB=y CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y diff --git a/configs/twister_defconfig b/configs/twister_defconfig index ba7b68b317..62d7d17ca9 100644 --- a/configs/twister_defconfig +++ b/configs/twister_defconfig @@ -26,6 +26,7 @@ CONFIG_CMD_UBI=y CONFIG_MMC_OMAP_HS=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_ULPI_VIEWPORT_OMAP=y CONFIG_USB_ULPI=y CONFIG_USB_STORAGE=y diff --git a/configs/v38b_defconfig b/configs/v38b_defconfig index db4c47c3d2..18dc039d93 100644 --- a/configs/v38b_defconfig +++ b/configs/v38b_defconfig @@ -3,13 +3,11 @@ CONFIG_MPC5xxx=y CONFIG_TARGET_V38B=y CONFIG_BOOTDELAY=3 CONFIG_BOARD_EARLY_INIT_F=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_PING=y -CONFIG_CMD_DATE=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y CONFIG_MAC_PARTITION=y diff --git a/configs/vct_platinum_defconfig b/configs/vct_platinum_defconfig index 27b29fb94e..259b48f5aa 100644 --- a/configs/vct_platinum_defconfig +++ b/configs/vct_platinum_defconfig @@ -14,4 +14,5 @@ CONFIG_CMD_FAT=y CONFIG_MTD_NOR_FLASH=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y diff --git a/configs/vct_platinum_onenand_defconfig b/configs/vct_platinum_onenand_defconfig index 4896c6b459..6d2d14f8a2 100644 --- a/configs/vct_platinum_onenand_defconfig +++ b/configs/vct_platinum_onenand_defconfig @@ -17,4 +17,5 @@ CONFIG_CMD_FAT=y CONFIG_CMD_UBI=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y diff --git a/configs/vct_premium_defconfig b/configs/vct_premium_defconfig index d5927b383b..3996d9da50 100644 --- a/configs/vct_premium_defconfig +++ b/configs/vct_premium_defconfig @@ -14,4 +14,5 @@ CONFIG_CMD_FAT=y CONFIG_MTD_NOR_FLASH=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y diff --git a/configs/vct_premium_onenand_defconfig b/configs/vct_premium_onenand_defconfig index e0c8a7176e..6bbdc3b0e6 100644 --- a/configs/vct_premium_onenand_defconfig +++ b/configs/vct_premium_onenand_defconfig @@ -17,4 +17,5 @@ CONFIG_CMD_FAT=y CONFIG_CMD_UBI=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y diff --git a/configs/venice2_defconfig b/configs/venice2_defconfig index 1b0e646474..97960e720e 100644 --- a/configs/venice2_defconfig +++ b/configs/venice2_defconfig @@ -37,6 +37,7 @@ CONFIG_SYS_NS16550=y CONFIG_TEGRA114_SPI=y CONFIG_USB=y CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_CI_UDC=y diff --git a/configs/ventana_defconfig b/configs/ventana_defconfig index 486861b461..8d3e54e8d7 100644 --- a/configs/ventana_defconfig +++ b/configs/ventana_defconfig @@ -30,6 +30,7 @@ CONFIG_PWM_TEGRA=y CONFIG_SYS_NS16550=y CONFIG_USB=y CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_ULPI_VIEWPORT=y CONFIG_USB_ULPI=y CONFIG_USB_STORAGE=y diff --git a/configs/vinco_defconfig b/configs/vinco_defconfig index dc7f2c6697..c8da54d9b6 100644 --- a/configs/vinco_defconfig +++ b/configs/vinco_defconfig @@ -25,6 +25,7 @@ CONFIG_SPI_FLASH=y CONFIG_NETDEVICES=y CONFIG_ETH_DESIGNWARE=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_ATMEL_USBA=y diff --git a/configs/whistler_defconfig b/configs/whistler_defconfig index 6c27b36235..3ebfb79895 100644 --- a/configs/whistler_defconfig +++ b/configs/whistler_defconfig @@ -27,4 +27,5 @@ CONFIG_SPL_DM=y CONFIG_SYS_NS16550=y CONFIG_USB=y CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y diff --git a/configs/x600_defconfig b/configs/x600_defconfig index 01565ec33b..3aaba16c2e 100644 --- a/configs/x600_defconfig +++ b/configs/x600_defconfig @@ -36,6 +36,7 @@ CONFIG_MTD_NOR_FLASH=y CONFIG_NETDEVICES=y CONFIG_ETH_DESIGNWARE=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y CONFIG_USE_TINY_PRINTF=y CONFIG_OF_LIBFDT=y diff --git a/configs/xfi3_defconfig b/configs/xfi3_defconfig index ce1ad56c0b..398d32f701 100644 --- a/configs/xfi3_defconfig +++ b/configs/xfi3_defconfig @@ -26,6 +26,7 @@ CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_MMC_MXS=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_GADGET=y CONFIG_CI_UDC=y CONFIG_OF_LIBFDT=y diff --git a/configs/zmx25_defconfig b/configs/zmx25_defconfig index 54e8dde1cf..7a939036d9 100644 --- a/configs/zmx25_defconfig +++ b/configs/zmx25_defconfig @@ -18,4 +18,5 @@ CONFIG_CMD_FAT=y # CONFIG_MMC is not set CONFIG_MTD_NOR_FLASH=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y diff --git a/doc/README.omap-reset-time b/doc/README.omap-reset-time deleted file mode 100644 index 0c974bacae..0000000000 --- a/doc/README.omap-reset-time +++ /dev/null @@ -1,20 +0,0 @@ -README on how reset time on OMAPs should be calculated - -CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC: -Most OMAPs' provide a way to specify the time for -which the reset should be held low while the voltages -and Oscillator outputs stabilize. - -This time is mostly board and PMIC dependent. Hence the -boards are expected to specify a pre-computed time -using the above option, (the details on how to compute -the value are given below) without which a default time -as specified by CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC -is used. - -The value for CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC -can be computed using a summation of the below 3 parameters --1- Time taken by the Osciallator to stop and restart --2- PMIC OTP time --3- Voltage ramp time, which can be derived using the -PMIC slew rate and value of voltage ramp needed. diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig index 325d053931..15135e538d 100644 --- a/drivers/gpio/Kconfig +++ b/drivers/gpio/Kconfig @@ -95,6 +95,14 @@ config MSM_GPIO - APQ8016 - MSM8916 +config OMAP_GPIO + bool "TI OMAP GPIO driver" + depends on ARCH_OMAP2PLUS + default y + help + Support GPIO controllers on the TI OMAP3/4/5 and related (such as + AM335x/AM43xx/AM57xx/DRA7xx/etc) families of SoCs. + config PM8916_GPIO bool "Qualcomm PM8916 PMIC GPIO/keypad driver" depends on DM_GPIO && PMIC_PM8916 diff --git a/drivers/i2c/fsl_i2c.c b/drivers/i2c/fsl_i2c.c index a1406baa87..ff3dc25927 100644 --- a/drivers/i2c/fsl_i2c.c +++ b/drivers/i2c/fsl_i2c.c @@ -284,15 +284,6 @@ static void __i2c_init(const struct fsl_i2c_base *base, int speed, int break; } - -#ifdef CONFIG_SYS_I2C_BOARD_LATE_INIT - /* Call board specific i2c bus reset routine AFTER the bus has been - * initialized. Use either this callpoint or i2c_init_board; - * which is called before i2c_init operations. - * For details about this problem see doc/I2C_Edge_Conditions. - */ - i2c_board_late_init(); -#endif } static int diff --git a/drivers/i2c/fti2c010.c b/drivers/i2c/fti2c010.c index b35d0d2d9c..4da959fa53 100644 --- a/drivers/i2c/fti2c010.c +++ b/drivers/i2c/fti2c010.c @@ -146,15 +146,6 @@ static void fti2c010_init(struct i2c_adapter *adap, int speed, int slaveaddr) set_i2c_bus_speed(chip, speed); /* slave init, don't care */ - -#ifdef CONFIG_SYS_I2C_BOARD_LATE_INIT - /* Call board specific i2c bus reset routine AFTER the bus has been - * initialized. Use either this callpoint or i2c_init_board; - * which is called before fti2c010_init operations. - * For details about this problem see doc/I2C_Edge_Conditions. - */ - i2c_board_late_init(); -#endif } /* diff --git a/drivers/i2c/mxc_i2c.c b/drivers/i2c/mxc_i2c.c index 13ec0e63b1..b68e82770b 100644 --- a/drivers/i2c/mxc_i2c.c +++ b/drivers/i2c/mxc_i2c.c @@ -69,10 +69,6 @@ DECLARE_GLOBAL_DATA_PTR; #define I2SR_IIF_CLEAR (0 << 1) #endif -#if defined(CONFIG_HARD_I2C) && !defined(CONFIG_SYS_I2C_BASE) -#error "define CONFIG_SYS_I2C_BASE to use the mxc_i2c driver" -#endif - #ifdef I2C_QUIRK_REG static u16 i2c_clk_div[60][2] = { { 20, 0x00 }, { 22, 0x01 }, { 24, 0x02 }, { 26, 0x03 }, diff --git a/drivers/i2c/omap24xx_i2c.c b/drivers/i2c/omap24xx_i2c.c index a23737ab78..4b8397a890 100644 --- a/drivers/i2c/omap24xx_i2c.c +++ b/drivers/i2c/omap24xx_i2c.c @@ -122,7 +122,7 @@ static int wait_for_bb(struct i2c *i2c_base, int waitdelay) u16 stat; writew(0xFFFF, &i2c_base->stat); /* clear current interrupts...*/ -#if defined(CONFIG_OMAP243X) || defined(CONFIG_OMAP34XX) +#if defined(CONFIG_OMAP34XX) while ((stat = readw(&i2c_base->stat) & I2C_STAT_BB) && timeout--) { #else /* Read RAW status */ @@ -153,7 +153,7 @@ static u16 wait_for_event(struct i2c *i2c_base, int waitdelay) do { udelay(waitdelay); -#if defined(CONFIG_OMAP243X) || defined(CONFIG_OMAP34XX) +#if defined(CONFIG_OMAP34XX) status = readw(&i2c_base->stat); #else /* Read RAW status */ @@ -338,7 +338,7 @@ retry: /* own address */ writew(slaveadd, &i2c_base->oa); -#if defined(CONFIG_OMAP243X) || defined(CONFIG_OMAP34XX) +#if defined(CONFIG_OMAP34XX) /* * Have to enable interrupts for OMAP2/3, these IPs don't have * an 'irqstatus_raw' register and we shall have to poll 'stat' diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig index a7d56e605d..d8c107e206 100644 --- a/drivers/power/Kconfig +++ b/drivers/power/Kconfig @@ -311,6 +311,7 @@ config SY8106A_VOUT1_VOLT config TWL4030_POWER depends on OMAP34XX bool "Enable driver for TI TWL4030 power management chip" + imply CMD_POWEROFF ---help--- The TWL4030 in a combination audio CODEC/power management with GPIO and it is commonly used with the OMAP3 family of processors diff --git a/drivers/serial/ns16550.c b/drivers/serial/ns16550.c index ca55df78b7..0eb7c02561 100644 --- a/drivers/serial/ns16550.c +++ b/drivers/serial/ns16550.c @@ -175,21 +175,17 @@ void NS16550_init(NS16550_t com_port, int baud_divisor) ; serial_out(CONFIG_SYS_NS16550_IER, &com_port->ier); -#if defined(CONFIG_OMAP) || defined(CONFIG_AM33XX) || \ - defined(CONFIG_TI81XX) || defined(CONFIG_AM43XX) +#if defined(CONFIG_ARCH_OMAP2PLUS) serial_out(0x7, &com_port->mdr1); /* mode select reset TL16C750*/ #endif serial_out(UART_MCRVAL, &com_port->mcr); serial_out(ns16550_getfcr(com_port), &com_port->fcr); if (baud_divisor != -1) NS16550_setbrg(com_port, baud_divisor); -#if defined(CONFIG_OMAP) || \ - defined(CONFIG_AM33XX) || defined(CONFIG_SOC_DA8XX) || \ - defined(CONFIG_TI81XX) || defined(CONFIG_AM43XX) - +#if defined(CONFIG_ARCH_OMAP2PLUS) || defined(CONFIG_SOC_DA8XX) /* /16 is proper to hit 115200 with 48MHz */ serial_out(0, &com_port->mdr1); -#endif /* CONFIG_OMAP */ +#endif #if defined(CONFIG_SOC_KEYSTONE) serial_out(UART_REG_VAL_PWREMU_MGMT_UART_ENABLE, &com_port->regC); #endif diff --git a/drivers/spi/omap3_spi.c b/drivers/spi/omap3_spi.c index 76d376ac44..3caea151c5 100644 --- a/drivers/spi/omap3_spi.c +++ b/drivers/spi/omap3_spi.c @@ -568,7 +568,8 @@ struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs, priv->freq = max_hz; priv->mode = mode; priv->wordlen = priv->slave.wordlen; -#ifdef CONFIG_OMAP3_SPI_D0_D1_SWAPPED +#if 0 + /* Please migrate to DM_SPI support for this feature. */ priv->pin_dir = MCSPI_PINDIR_D0_OUT_D1_IN; #endif diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig index fb5aa6f889..9a67e43c2d 100644 --- a/drivers/usb/host/Kconfig +++ b/drivers/usb/host/Kconfig @@ -57,6 +57,7 @@ endif # USB_XHCI_HCD config USB_EHCI_HCD bool "EHCI HCD (USB 2.0) support" + default y if ARCH_MX5 || ARCH_MX6 select USB_HOST ---help--- The Enhanced Host Controller Interface (EHCI) is standard for USB 2.0 @@ -74,12 +75,6 @@ config USB_EHCI_HCD You may want to read <file:Documentation/usb/ehci.txt>. -config USB_EHCI - bool - default USB_EHCI_HCD - ---help--- - TODO: rename after most boards switch to Kconfig - if USB_EHCI_HCD config USB_EHCI_ATMEL @@ -90,8 +85,8 @@ config USB_EHCI_ATMEL Enables support for the on-chip EHCI controller on Atmel chips. config USB_EHCI_MARVELL - bool "Support for MVEBU (AXP / A38x) on-chip EHCI USB controller" - depends on ARCH_MVEBU + bool "Support for Marvell on-chip EHCI USB controller" + depends on ARCH_MVEBU || KIRKWOOD || ORION5X default y ---help--- Enables support for the on-chip EHCI controller on MVEBU SoCs. @@ -110,6 +105,14 @@ config USB_EHCI_MX7 ---help--- Enables support for the on-chip EHCI controller on i.MX7 SoCs. +config USB_EHCI_OMAP + bool "Support for OMAP3+ on-chip EHCI USB controller" + depends on ARCH_OMAP2PLUS + default y + ---help--- + Enables support for the on-chip EHCI controller on OMAP3 and later + SoCs. + if USB_EHCI_MX7 config MXC_USB_OTG_HACTIVE diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile index 58c0cf54c2..bf354fe8d5 100644 --- a/drivers/usb/host/Makefile +++ b/drivers/usb/host/Makefile @@ -24,7 +24,7 @@ obj-$(CONFIG_USB_OHCI_LPC32XX) += ohci-lpc32xx.o obj-$(CONFIG_USB_OHCI_GENERIC) += ohci-generic.o # echi -obj-$(CONFIG_USB_EHCI) += ehci-hcd.o +obj-$(CONFIG_USB_EHCI_HCD) += ehci-hcd.o obj-$(CONFIG_USB_EHCI_ARMADA100) += ehci-armada100.o utmi-armada100.o obj-$(CONFIG_USB_EHCI_ATMEL) += ehci-atmel.o ifdef CONFIG_MPC512X diff --git a/drivers/usb/musb-new/linux-compat.h b/drivers/usb/musb-new/linux-compat.h index 9244977579..4dae83ed68 100644 --- a/drivers/usb/musb-new/linux-compat.h +++ b/drivers/usb/musb-new/linux-compat.h @@ -30,7 +30,7 @@ #define CONFIG_SOC_OMAP3430 #endif -#ifdef CONFIG_OMAP4430 +#ifdef CONFIG_OMAP44XX #define CONFIG_ARCH_OMAP4 #endif diff --git a/drivers/usb/musb-new/omap2430.c b/drivers/usb/musb-new/omap2430.c index 684ad9539a..ba22dfe6cb 100644 --- a/drivers/usb/musb-new/omap2430.c +++ b/drivers/usb/musb-new/omap2430.c @@ -441,7 +441,7 @@ static int omap2430_musb_enable(struct musb *musb) twl6030_usb_device_settings(); #endif -#ifdef CONFIG_OMAP4430 +#ifdef CONFIG_OMAP44XX u32 *usbotghs_control = (u32 *)((*ctrl)->control_usbotghs_ctrl); *usbotghs_control = USBOTGHS_CONTROL_AVALID | USBOTGHS_CONTROL_VBUSVALID | USBOTGHS_CONTROL_IDDIG; diff --git a/drivers/usb/musb/omap3.c b/drivers/usb/musb/omap3.c index 97da529b44..57889ef0e7 100644 --- a/drivers/usb/musb/omap3.c +++ b/drivers/usb/musb/omap3.c @@ -55,7 +55,7 @@ static struct omap3_otg_regs *otg; #define OMAP3_OTG_SYSSTATUS_RESETDONE 0x0001 /* OMAP4430 has an internal PHY, use it */ -#ifdef CONFIG_OMAP4430 +#ifdef CONFIG_OMAP44XX #define OMAP3_OTG_INTERFSEL_OMAP 0x0000 #else #define OMAP3_OTG_INTERFSEL_OMAP 0x0001 @@ -118,11 +118,11 @@ int musb_platform_init(void) stdby &= ~OMAP3_OTG_FORCESTDBY_STANDBY; writel(stdby, &otg->forcestdby); -#ifdef CONFIG_OMAP3_EVM +#ifdef CONFIG_TARGET_OMAP3_EVM musb_cfg.extvbus = omap3_evm_need_extvbus(); #endif -#ifdef CONFIG_OMAP4430 +#ifdef CONFIG_OMAP44XX u32 *usbotghs_control = (u32 *)((*ctrl)->control_usbotghs_ctrl); *usbotghs_control = 0x15; diff --git a/drivers/usb/musb/omap3.h b/drivers/usb/musb/omap3.h index ae645c72de..d91ad0a85b 100644 --- a/drivers/usb/musb/omap3.h +++ b/drivers/usb/musb/omap3.h @@ -32,7 +32,7 @@ int musb_platform_init(void); -#ifdef CONFIG_OMAP3_EVM +#ifdef CONFIG_TARGET_OMAP3_EVM extern u8 omap3_evm_need_extvbus(void); #endif diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig index 446cca90d4..61dfed8c06 100644 --- a/drivers/video/Kconfig +++ b/drivers/video/Kconfig @@ -619,4 +619,13 @@ config LCD CONFIG option. See the README for details. Drives which have been converted to driver model will instead used CONFIG_DM_VIDEO. +config VIDEO_DW_HDMI + bool + help + Enables the common driver code for the Designware HDMI TX + block found in SoCs from various vendors. + As this does not provide any functionality by itself (but + rather requires a SoC-specific glue driver to call it), it + can not be enabled from the configuration menu. + endmenu diff --git a/drivers/video/Makefile b/drivers/video/Makefile index a80af3104d..58f5de5200 100644 --- a/drivers/video/Makefile +++ b/drivers/video/Makefile @@ -57,6 +57,7 @@ obj-$(CONFIG_VIDEO_VESA) += vesa.o obj-$(CONFIG_FORMIKE) += formike.o obj-$(CONFIG_LG4573) += lg4573.o obj-$(CONFIG_AM335X_LCD) += am335x-fb.o +obj-$(CONFIG_VIDEO_DW_HDMI) += dw_hdmi.o obj-${CONFIG_VIDEO_TEGRA124} += tegra124/ obj-${CONFIG_EXYNOS_FB} += exynos/ diff --git a/drivers/video/dw_hdmi.c b/drivers/video/dw_hdmi.c index 8a53109823..6039d676c5 100644 --- a/drivers/video/dw_hdmi.c +++ b/drivers/video/dw_hdmi.c @@ -414,13 +414,9 @@ static void hdmi_av_composer(struct dw_hdmi *hdmi, HDMI_FC_INVIDCONF_DE_IN_POLARITY_ACTIVE_HIGH : HDMI_FC_INVIDCONF_DE_IN_POLARITY_ACTIVE_LOW); - /* - * TODO(sjg@chromium.org>: Need to check for HDMI / DVI - * inv_val |= (edid->hdmi_monitor_detected ? - * HDMI_FC_INVIDCONF_DVI_MODEZ_HDMI_MODE : - * HDMI_FC_INVIDCONF_DVI_MODEZ_DVI_MODE); - */ - inv_val |= HDMI_FC_INVIDCONF_DVI_MODEZ_HDMI_MODE; + inv_val |= (edid->hdmi_monitor ? + HDMI_FC_INVIDCONF_DVI_MODEZ_HDMI_MODE : + HDMI_FC_INVIDCONF_DVI_MODEZ_DVI_MODE); inv_val |= HDMI_FC_INVIDCONF_R_V_BLANK_IN_OSC_ACTIVE_LOW; @@ -459,7 +455,7 @@ static void hdmi_av_composer(struct dw_hdmi *hdmi, } /* hdmi initialization step b.4 */ -static void hdmi_enable_video_path(struct dw_hdmi *hdmi) +static void hdmi_enable_video_path(struct dw_hdmi *hdmi, bool audio) { uint clkdis; @@ -484,8 +480,10 @@ static void hdmi_enable_video_path(struct dw_hdmi *hdmi) clkdis &= ~HDMI_MC_CLKDIS_TMDSCLK_DISABLE; hdmi_write(hdmi, clkdis, HDMI_MC_CLKDIS); - clkdis &= ~HDMI_MC_CLKDIS_AUDCLK_DISABLE; - hdmi_write(hdmi, clkdis, HDMI_MC_CLKDIS); + if (audio) { + clkdis &= ~HDMI_MC_CLKDIS_AUDCLK_DISABLE; + hdmi_write(hdmi, clkdis, HDMI_MC_CLKDIS); + } } /* workaround to clear the overflow condition */ @@ -716,7 +714,8 @@ int dw_hdmi_enable(struct dw_hdmi *hdmi, const struct display_timing *edid) { int ret; - debug("hdmi, mode info : clock %d hdis %d vdis %d\n", + debug("%s, mode info : clock %d hdis %d vdis %d\n", + edid->hdmi_monitor ? "hdmi" : "dvi", edid->pixelclock.typ, edid->hactive.typ, edid->vactive.typ); hdmi_av_composer(hdmi, edid); @@ -725,11 +724,13 @@ int dw_hdmi_enable(struct dw_hdmi *hdmi, const struct display_timing *edid) if (ret) return ret; - hdmi_enable_video_path(hdmi); + hdmi_enable_video_path(hdmi, edid->hdmi_monitor); - hdmi_audio_fifo_reset(hdmi); - hdmi_audio_set_format(hdmi); - hdmi_audio_set_samplerate(hdmi, edid->pixelclock.typ); + if (edid->hdmi_monitor) { + hdmi_audio_fifo_reset(hdmi); + hdmi_audio_set_format(hdmi); + hdmi_audio_set_samplerate(hdmi, edid->pixelclock.typ); + } hdmi_video_packetize(hdmi); hdmi_video_sample(hdmi); diff --git a/drivers/video/rockchip/Kconfig b/drivers/video/rockchip/Kconfig index 9267b28781..80e399f7d7 100644 --- a/drivers/video/rockchip/Kconfig +++ b/drivers/video/rockchip/Kconfig @@ -35,6 +35,7 @@ config DISPLAY_ROCKCHIP_LVDS config DISPLAY_ROCKCHIP_HDMI bool "HDMI port" + select VIDEO_DW_HDMI depends on VIDEO_ROCKCHIP help This enables High-Definition Multimedia Interface display support. diff --git a/drivers/video/rockchip/Makefile b/drivers/video/rockchip/Makefile index c742902ddb..cd54b12a4e 100644 --- a/drivers/video/rockchip/Makefile +++ b/drivers/video/rockchip/Makefile @@ -9,6 +9,6 @@ ifdef CONFIG_VIDEO_ROCKCHIP obj-y += rk_vop.o obj-$(CONFIG_DISPLAY_ROCKCHIP_EDP) += rk_edp.o obj-$(CONFIG_DISPLAY_ROCKCHIP_LVDS) += rk_lvds.o -obj-$(CONFIG_DISPLAY_ROCKCHIP_HDMI) += rk_hdmi.o ../dw_hdmi.o +obj-$(CONFIG_DISPLAY_ROCKCHIP_HDMI) += rk_hdmi.o obj-$(CONFIG_DISPLAY_ROCKCHIP_MIPI) += rk_mipi.o endif diff --git a/drivers/video/sunxi/Makefile b/drivers/video/sunxi/Makefile index b8afd892ad..dbaab61b59 100644 --- a/drivers/video/sunxi/Makefile +++ b/drivers/video/sunxi/Makefile @@ -5,5 +5,5 @@ # SPDX-License-Identifier: GPL-2.0+ # -obj-$(CONFIG_VIDEO_SUNXI) += sunxi_display.o lcdc.o ../videomodes.o +obj-$(CONFIG_VIDEO_SUNXI) += sunxi_display.o lcdc.o tve.o ../videomodes.o obj-$(CONFIG_VIDEO_DE2) += sunxi_de2.o sunxi_dw_hdmi.o lcdc.o ../dw_hdmi.o diff --git a/drivers/video/sunxi/sunxi_display.c b/drivers/video/sunxi/sunxi_display.c index 92c9d06054..de768ba94a 100644 --- a/drivers/video/sunxi/sunxi_display.c +++ b/drivers/video/sunxi/sunxi_display.c @@ -14,6 +14,7 @@ #include <asm/arch/gpio.h> #include <asm/arch/lcdc.h> #include <asm/arch/pwm.h> +#include <asm/arch/tve.h> #include <asm/global_data.h> #include <asm/gpio.h> #include <asm/io.h> @@ -929,63 +930,19 @@ static void sunxi_tvencoder_mode_set(void) switch (sunxi_display.monitor) { case sunxi_monitor_vga: - writel(SUNXI_TVE_GCTRL_DAC_INPUT(0, 1) | - SUNXI_TVE_GCTRL_DAC_INPUT(1, 2) | - SUNXI_TVE_GCTRL_DAC_INPUT(2, 3), &tve->gctrl); - writel(SUNXI_TVE_CFG0_VGA, &tve->cfg0); - writel(SUNXI_TVE_DAC_CFG0_VGA, &tve->dac_cfg0); - writel(SUNXI_TVE_UNKNOWN1_VGA, &tve->unknown1); + tvencoder_mode_set(tve, tve_mode_vga); break; case sunxi_monitor_composite_pal_nc: - writel(SUNXI_TVE_CHROMA_FREQ_PAL_NC, &tve->chroma_freq); - /* Fall through */ + tvencoder_mode_set(tve, tve_mode_composite_pal_nc); + break; case sunxi_monitor_composite_pal: - writel(SUNXI_TVE_GCTRL_DAC_INPUT(0, 1) | - SUNXI_TVE_GCTRL_DAC_INPUT(1, 2) | - SUNXI_TVE_GCTRL_DAC_INPUT(2, 3) | - SUNXI_TVE_GCTRL_DAC_INPUT(3, 4), &tve->gctrl); - writel(SUNXI_TVE_CFG0_PAL, &tve->cfg0); - writel(SUNXI_TVE_DAC_CFG0_COMPOSITE, &tve->dac_cfg0); - writel(SUNXI_TVE_FILTER_COMPOSITE, &tve->filter); - writel(SUNXI_TVE_PORCH_NUM_PAL, &tve->porch_num); - writel(SUNXI_TVE_LINE_NUM_PAL, &tve->line_num); - writel(SUNXI_TVE_BLANK_BLACK_LEVEL_PAL, &tve->blank_black_level); - writel(SUNXI_TVE_UNKNOWN1_COMPOSITE, &tve->unknown1); - writel(SUNXI_TVE_CBR_LEVEL_PAL, &tve->cbr_level); - writel(SUNXI_TVE_BURST_WIDTH_COMPOSITE, &tve->burst_width); - writel(SUNXI_TVE_UNKNOWN2_PAL, &tve->unknown2); - writel(SUNXI_TVE_ACTIVE_NUM_COMPOSITE, &tve->active_num); - writel(SUNXI_TVE_CHROMA_BW_GAIN_COMP, &tve->chroma_bw_gain); - writel(SUNXI_TVE_NOTCH_WIDTH_COMPOSITE, &tve->notch_width); - writel(SUNXI_TVE_RESYNC_NUM_PAL, &tve->resync_num); - writel(SUNXI_TVE_SLAVE_PARA_COMPOSITE, &tve->slave_para); + tvencoder_mode_set(tve, tve_mode_composite_pal); break; case sunxi_monitor_composite_pal_m: - writel(SUNXI_TVE_CHROMA_FREQ_PAL_M, &tve->chroma_freq); - writel(SUNXI_TVE_COLOR_BURST_PAL_M, &tve->color_burst); - /* Fall through */ + tvencoder_mode_set(tve, tve_mode_composite_pal_m); + break; case sunxi_monitor_composite_ntsc: - writel(SUNXI_TVE_GCTRL_DAC_INPUT(0, 1) | - SUNXI_TVE_GCTRL_DAC_INPUT(1, 2) | - SUNXI_TVE_GCTRL_DAC_INPUT(2, 3) | - SUNXI_TVE_GCTRL_DAC_INPUT(3, 4), &tve->gctrl); - writel(SUNXI_TVE_CFG0_NTSC, &tve->cfg0); - writel(SUNXI_TVE_DAC_CFG0_COMPOSITE, &tve->dac_cfg0); - writel(SUNXI_TVE_FILTER_COMPOSITE, &tve->filter); - writel(SUNXI_TVE_PORCH_NUM_NTSC, &tve->porch_num); - writel(SUNXI_TVE_LINE_NUM_NTSC, &tve->line_num); - writel(SUNXI_TVE_BLANK_BLACK_LEVEL_NTSC, &tve->blank_black_level); - writel(SUNXI_TVE_UNKNOWN1_COMPOSITE, &tve->unknown1); - writel(SUNXI_TVE_CBR_LEVEL_NTSC, &tve->cbr_level); - writel(SUNXI_TVE_BURST_PHASE_NTSC, &tve->burst_phase); - writel(SUNXI_TVE_BURST_WIDTH_COMPOSITE, &tve->burst_width); - writel(SUNXI_TVE_UNKNOWN2_NTSC, &tve->unknown2); - writel(SUNXI_TVE_SYNC_VBI_LEVEL_NTSC, &tve->sync_vbi_level); - writel(SUNXI_TVE_ACTIVE_NUM_COMPOSITE, &tve->active_num); - writel(SUNXI_TVE_CHROMA_BW_GAIN_COMP, &tve->chroma_bw_gain); - writel(SUNXI_TVE_NOTCH_WIDTH_COMPOSITE, &tve->notch_width); - writel(SUNXI_TVE_RESYNC_NUM_NTSC, &tve->resync_num); - writel(SUNXI_TVE_SLAVE_PARA_COMPOSITE, &tve->slave_para); + tvencoder_mode_set(tve, tve_mode_composite_ntsc); break; case sunxi_monitor_none: case sunxi_monitor_dvi: @@ -995,14 +952,6 @@ static void sunxi_tvencoder_mode_set(void) } } -static void sunxi_tvencoder_enable(void) -{ - struct sunxi_tve_reg * const tve = - (struct sunxi_tve_reg *)SUNXI_TVE0_BASE; - - setbits_le32(&tve->gctrl, SUNXI_TVE_GCTRL_ENABLE); -} - #endif /* CONFIG_VIDEO_VGA || defined CONFIG_VIDEO_COMPOSITE */ static void sunxi_drc_init(void) @@ -1080,6 +1029,8 @@ static void sunxi_mode_set(const struct ctfb_res_modes *mode, int __maybe_unused clk_div, clk_double; struct sunxi_lcdc_reg * const lcdc = (struct sunxi_lcdc_reg *)SUNXI_LCD0_BASE; + struct sunxi_tve_reg * __maybe_unused const tve = + (struct sunxi_tve_reg *)SUNXI_TVE0_BASE; switch (sunxi_display.monitor) { case sunxi_monitor_none: @@ -1134,7 +1085,7 @@ static void sunxi_mode_set(const struct ctfb_res_modes *mode, sunxi_tvencoder_mode_set(); sunxi_composer_enable(); lcdc_enable(lcdc, sunxi_display.depth); - sunxi_tvencoder_enable(); + tvencoder_enable(tve); #elif defined CONFIG_VIDEO_VGA_VIA_LCD sunxi_composer_mode_set(mode, address); sunxi_lcdc_tcon0_mode_set(mode, true); @@ -1153,7 +1104,7 @@ static void sunxi_mode_set(const struct ctfb_res_modes *mode, sunxi_tvencoder_mode_set(); sunxi_composer_enable(); lcdc_enable(lcdc, sunxi_display.depth); - sunxi_tvencoder_enable(); + tvencoder_enable(tve); #endif break; } diff --git a/drivers/video/sunxi/tve.c b/drivers/video/sunxi/tve.c new file mode 100644 index 0000000000..adea78a69a --- /dev/null +++ b/drivers/video/sunxi/tve.c @@ -0,0 +1,86 @@ +/* + * TV encoder driver for Allwinner SoCs. + * + * (C) Copyright 2013-2014 Luc Verhaegen <libv@skynet.be> + * (C) Copyright 2014-2015 Hans de Goede <hdegoede@redhat.com> + * (C) Copyright 2017 Jernej Skrabec <jernej.skrabec@siol.net> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> + +#include <asm/arch/tve.h> +#include <asm/io.h> + +void tvencoder_mode_set(struct sunxi_tve_reg * const tve, enum tve_mode mode) +{ + switch (mode) { + case tve_mode_vga: + writel(SUNXI_TVE_GCTRL_DAC_INPUT(0, 1) | + SUNXI_TVE_GCTRL_DAC_INPUT(1, 2) | + SUNXI_TVE_GCTRL_DAC_INPUT(2, 3), &tve->gctrl); + writel(SUNXI_TVE_CFG0_VGA, &tve->cfg0); + writel(SUNXI_TVE_DAC_CFG0_VGA, &tve->dac_cfg0); + writel(SUNXI_TVE_UNKNOWN1_VGA, &tve->unknown1); + break; + case tve_mode_composite_pal_nc: + writel(SUNXI_TVE_CHROMA_FREQ_PAL_NC, &tve->chroma_freq); + /* Fall through */ + case tve_mode_composite_pal: + writel(SUNXI_TVE_GCTRL_DAC_INPUT(0, 1) | + SUNXI_TVE_GCTRL_DAC_INPUT(1, 2) | + SUNXI_TVE_GCTRL_DAC_INPUT(2, 3) | + SUNXI_TVE_GCTRL_DAC_INPUT(3, 4), &tve->gctrl); + writel(SUNXI_TVE_CFG0_PAL, &tve->cfg0); + writel(SUNXI_TVE_DAC_CFG0_COMPOSITE, &tve->dac_cfg0); + writel(SUNXI_TVE_FILTER_COMPOSITE, &tve->filter); + writel(SUNXI_TVE_PORCH_NUM_PAL, &tve->porch_num); + writel(SUNXI_TVE_LINE_NUM_PAL, &tve->line_num); + writel(SUNXI_TVE_BLANK_BLACK_LEVEL_PAL, + &tve->blank_black_level); + writel(SUNXI_TVE_UNKNOWN1_COMPOSITE, &tve->unknown1); + writel(SUNXI_TVE_CBR_LEVEL_PAL, &tve->cbr_level); + writel(SUNXI_TVE_BURST_WIDTH_COMPOSITE, &tve->burst_width); + writel(SUNXI_TVE_UNKNOWN2_PAL, &tve->unknown2); + writel(SUNXI_TVE_ACTIVE_NUM_COMPOSITE, &tve->active_num); + writel(SUNXI_TVE_CHROMA_BW_GAIN_COMP, &tve->chroma_bw_gain); + writel(SUNXI_TVE_NOTCH_WIDTH_COMPOSITE, &tve->notch_width); + writel(SUNXI_TVE_RESYNC_NUM_PAL, &tve->resync_num); + writel(SUNXI_TVE_SLAVE_PARA_COMPOSITE, &tve->slave_para); + break; + case tve_mode_composite_pal_m: + writel(SUNXI_TVE_CHROMA_FREQ_PAL_M, &tve->chroma_freq); + writel(SUNXI_TVE_COLOR_BURST_PAL_M, &tve->color_burst); + /* Fall through */ + case tve_mode_composite_ntsc: + writel(SUNXI_TVE_GCTRL_DAC_INPUT(0, 1) | + SUNXI_TVE_GCTRL_DAC_INPUT(1, 2) | + SUNXI_TVE_GCTRL_DAC_INPUT(2, 3) | + SUNXI_TVE_GCTRL_DAC_INPUT(3, 4), &tve->gctrl); + writel(SUNXI_TVE_CFG0_NTSC, &tve->cfg0); + writel(SUNXI_TVE_DAC_CFG0_COMPOSITE, &tve->dac_cfg0); + writel(SUNXI_TVE_FILTER_COMPOSITE, &tve->filter); + writel(SUNXI_TVE_PORCH_NUM_NTSC, &tve->porch_num); + writel(SUNXI_TVE_LINE_NUM_NTSC, &tve->line_num); + writel(SUNXI_TVE_BLANK_BLACK_LEVEL_NTSC, + &tve->blank_black_level); + writel(SUNXI_TVE_UNKNOWN1_COMPOSITE, &tve->unknown1); + writel(SUNXI_TVE_CBR_LEVEL_NTSC, &tve->cbr_level); + writel(SUNXI_TVE_BURST_PHASE_NTSC, &tve->burst_phase); + writel(SUNXI_TVE_BURST_WIDTH_COMPOSITE, &tve->burst_width); + writel(SUNXI_TVE_UNKNOWN2_NTSC, &tve->unknown2); + writel(SUNXI_TVE_SYNC_VBI_LEVEL_NTSC, &tve->sync_vbi_level); + writel(SUNXI_TVE_ACTIVE_NUM_COMPOSITE, &tve->active_num); + writel(SUNXI_TVE_CHROMA_BW_GAIN_COMP, &tve->chroma_bw_gain); + writel(SUNXI_TVE_NOTCH_WIDTH_COMPOSITE, &tve->notch_width); + writel(SUNXI_TVE_RESYNC_NUM_NTSC, &tve->resync_num); + writel(SUNXI_TVE_SLAVE_PARA_COMPOSITE, &tve->slave_para); + break; + } +} + +void tvencoder_enable(struct sunxi_tve_reg * const tve) +{ + setbits_le32(&tve->gctrl, SUNXI_TVE_GCTRL_ENABLE); +} diff --git a/drivers/video/video_bmp.c b/drivers/video/video_bmp.c index 32a4e7f8a9..f803067da3 100644 --- a/drivers/video/video_bmp.c +++ b/drivers/video/video_bmp.c @@ -316,7 +316,7 @@ int video_bmp_display(struct udevice *dev, ulong bmp_image, int x, int y, } break; #endif /* CONFIG_BMP_16BPP */ -#if defined(CONFIG_BMP_24BMP) +#if defined(CONFIG_BMP_24BPP) case 24: for (i = 0; i < height; ++i) { for (j = 0; j < width; j++) { @@ -328,7 +328,7 @@ int video_bmp_display(struct udevice *dev, ulong bmp_image, int x, int y, fb -= priv->line_length + width * (bpix / 8); } break; -#endif /* CONFIG_BMP_24BMP */ +#endif /* CONFIG_BMP_24BPP */ #if defined(CONFIG_BMP_32BPP) case 32: for (i = 0; i < height; ++i) { diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig index bdaf5d4101..22a7c4f801 100644 --- a/drivers/watchdog/Kconfig +++ b/drivers/watchdog/Kconfig @@ -12,6 +12,14 @@ config BCM2835_WDT This provides basic infrastructure to support BCM2835/2836 watchdog hardware, with a max timeout of ~15secs. +config OMAP_WATCHDOG + bool "TI OMAP watchdog driver" + depends on ARCH_OMAP2PLUS + select HW_WATCHDOG + default y if AM33XX + help + Say Y here to enable the OMAP3+ watchdog driver. + config ULP_WATCHDOG bool "i.MX7ULP watchdog" help diff --git a/include/atf_common.h b/include/atf_common.h new file mode 100644 index 0000000000..8c513e7c3e --- /dev/null +++ b/include/atf_common.h @@ -0,0 +1,183 @@ +/* + * This is from the ARM TF Project, + * Repository: https://github.com/ARM-software/arm-trusted-firmware.git + * File: include/common/bl_common.h + * Portions copyright (c) 2013-2016, ARM Limited and Contributors. All rights + * reserved. + * Copyright (C) 2016-2017 Rockchip Electronic Co.,Ltd + * + * SPDX-License-Identifier: BSD-3-Clause + */ + +#ifndef __BL_COMMON_H__ +#define __BL_COMMON_H__ + +#define ATF_PARAM_EP 0x01 +#define ATF_PARAM_IMAGE_BINARY 0x02 +#define ATF_PARAM_BL31 0x03 + +#define ATF_VERSION_1 0x01 + +#define ATF_EP_SECURE 0x0 +#define ATF_EP_NON_SECURE 0x1 + +#define SET_PARAM_HEAD(_p, _type, _ver, _attr) do { \ + (_p)->h.type = (uint8_t)(_type); \ + (_p)->h.version = (uint8_t)(_ver); \ + (_p)->h.size = (uint16_t)sizeof(*_p); \ + (_p)->h.attr = (uint32_t)(_attr) ; \ + } while (0) + +#define MODE_RW_SHIFT 0x4 +#define MODE_RW_MASK 0x1 +#define MODE_RW_64 0x0 +#define MODE_RW_32 0x1 + +#define MODE_EL_SHIFT 0x2 +#define MODE_EL_MASK 0x3 +#define MODE_EL3 0x3 +#define MODE_EL2 0x2 +#define MODE_EL1 0x1 +#define MODE_EL0 0x0 + +#define MODE_SP_SHIFT 0x0 +#define MODE_SP_MASK 0x1 +#define MODE_SP_EL0 0x0 +#define MODE_SP_ELX 0x1 + +#define SPSR_DAIF_SHIFT 6 +#define SPSR_DAIF_MASK 0x0f + +#define SPSR_64(el, sp, daif) \ + (MODE_RW_64 << MODE_RW_SHIFT | \ + ((el) & MODE_EL_MASK) << MODE_EL_SHIFT | \ + ((sp) & MODE_SP_MASK) << MODE_SP_SHIFT | \ + ((daif) & SPSR_DAIF_MASK) << SPSR_DAIF_SHIFT) + +#define SPSR_FIQ (1 << 6) +#define SPSR_IRQ (1 << 7) +#define SPSR_SERROR (1 << 8) +#define SPSR_DEBUG (1 << 9) +#define SPSR_EXCEPTION_MASK (SPSR_FIQ | SPSR_IRQ | SPSR_SERROR | SPSR_DEBUG) + +#define DAIF_FIQ_BIT (1<<0) +#define DAIF_IRQ_BIT (1<<1) +#define DAIF_ABT_BIT (1<<2) +#define DAIF_DBG_BIT (1<<3) +#define DISABLE_ALL_EXECPTIONS \ + (DAIF_FIQ_BIT | DAIF_IRQ_BIT | DAIF_ABT_BIT | DAIF_DBG_BIT) + +#ifndef __ASSEMBLY__ + +/******************************************************************************* + * Structure used for telling the next BL how much of a particular type of + * memory is available for its use and how much is already used. + ******************************************************************************/ +struct aapcs64_params { + unsigned long arg0; + unsigned long arg1; + unsigned long arg2; + unsigned long arg3; + unsigned long arg4; + unsigned long arg5; + unsigned long arg6; + unsigned long arg7; +}; + +/*************************************************************************** + * This structure provides version information and the size of the + * structure, attributes for the structure it represents + ***************************************************************************/ +struct param_header { + uint8_t type; /* type of the structure */ + uint8_t version; /* version of this structure */ + uint16_t size; /* size of this structure in bytes */ + uint32_t attr; /* attributes: unused bits SBZ */ +}; + +/***************************************************************************** + * This structure represents the superset of information needed while + * switching exception levels. The only two mechanisms to do so are + * ERET & SMC. Security state is indicated using bit zero of header + * attribute + * NOTE: BL1 expects entrypoint followed by spsr at an offset from the start + * of this structure defined by the macro `ENTRY_POINT_INFO_PC_OFFSET` while + * processing SMC to jump to BL31. + *****************************************************************************/ +struct entry_point_info { + struct param_header h; + uintptr_t pc; + uint32_t spsr; + struct aapcs64_params args; +}; + +/***************************************************************************** + * Image info binary provides information from the image loader that + * can be used by the firmware to manage available trusted RAM. + * More advanced firmware image formats can provide additional + * information that enables optimization or greater flexibility in the + * common firmware code + *****************************************************************************/ +struct atf_image_info { + struct param_header h; + uintptr_t image_base; /* physical address of base of image */ + uint32_t image_size; /* bytes read from image file */ +}; + +/***************************************************************************** + * The image descriptor struct definition. + *****************************************************************************/ +struct image_desc { + /* Contains unique image id for the image. */ + unsigned int image_id; + /* + * This member contains Image state information. + * Refer IMAGE_STATE_XXX defined above. + */ + unsigned int state; + uint32_t copied_size; /* image size copied in blocks */ + struct atf_image_info atf_image_info; + struct entry_point_info ep_info; +}; + +/******************************************************************************* + * This structure represents the superset of information that can be passed to + * BL31 e.g. while passing control to it from BL2. The BL32 parameters will be + * populated only if BL2 detects its presence. A pointer to a structure of this + * type should be passed in X0 to BL31's cold boot entrypoint. + * + * Use of this structure and the X0 parameter is not mandatory: the BL31 + * platform code can use other mechanisms to provide the necessary information + * about BL32 and BL33 to the common and SPD code. + * + * BL31 image information is mandatory if this structure is used. If either of + * the optional BL32 and BL33 image information is not provided, this is + * indicated by the respective image_info pointers being zero. + ******************************************************************************/ +struct bl31_params { + struct param_header h; + struct atf_image_info *bl31_image_info; + struct entry_point_info *bl32_ep_info; + struct atf_image_info *bl32_image_info; + struct entry_point_info *bl33_ep_info; + struct atf_image_info *bl33_image_info; +}; + +/******************************************************************************* + * This structure represents the superset of information that is passed to + * BL31, e.g. while passing control to it from BL2, bl31_params + * and other platform specific params + ******************************************************************************/ +struct bl2_to_bl31_params_mem { + struct bl31_params bl31_params; + struct atf_image_info bl31_image_info; + struct atf_image_info bl32_image_info; + struct atf_image_info bl33_image_info; + struct entry_point_info bl33_ep_info; + struct entry_point_info bl32_ep_info; + struct entry_point_info bl31_ep_info; +}; + +#endif /*__ASSEMBLY__*/ + +#endif /* __BL_COMMON_H__ */ diff --git a/include/common.h b/include/common.h index 83e4037a86..45f190a600 100644 --- a/include/common.h +++ b/include/common.h @@ -499,9 +499,19 @@ void reset_phy (void); void fdc_hw_init (void); /* $(BOARD)/eeprom.c */ +#ifdef CONFIG_CMD_EEPROM void eeprom_init (int bus); int eeprom_read (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt); int eeprom_write (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt); +#else +/* + * Some EEPROM code is depecated because it used the legacy I2C interface. Add + * some macros here so we don't have to touch every one of those uses + */ +#define eeprom_init(bus) +#define eeprom_read(dev_addr, offset, buffer, cnt) ((void)-ENOSYS) +#define eeprom_write(dev_addr, offset, buffer, cnt) ((void)-ENOSYS) +#endif /* * Set this up regardless of board diff --git a/include/configs/B4860QDS.h b/include/configs/B4860QDS.h index abfdbc9276..2041b7bb3e 100644 --- a/include/configs/B4860QDS.h +++ b/include/configs/B4860QDS.h @@ -723,9 +723,7 @@ unsigned long get_board_ddr_clk(void); #define CONFIG_HAS_FSL_DR_USB #ifdef CONFIG_HAS_FSL_DR_USB -#define CONFIG_USB_EHCI - -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD #define CONFIG_USB_EHCI_FSL #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #endif diff --git a/include/configs/BSC9131RDB.h b/include/configs/BSC9131RDB.h index 6f333e75ef..72dc8ba710 100644 --- a/include/configs/BSC9131RDB.h +++ b/include/configs/BSC9131RDB.h @@ -334,9 +334,7 @@ extern unsigned long get_sdram_size(void); #define CONFIG_SHA_HW_ACCEL #endif -#define CONFIG_USB_EHCI - -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_USB_EHCI_FSL #define CONFIG_HAS_FSL_DR_USB diff --git a/include/configs/BSC9132QDS.h b/include/configs/BSC9132QDS.h index 9097932581..1b956fc7da 100644 --- a/include/configs/BSC9132QDS.h +++ b/include/configs/BSC9132QDS.h @@ -476,8 +476,7 @@ combinations. this should be removed later #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR #endif -#define CONFIG_USB_EHCI /* USB */ -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_USB_EHCI_FSL #define CONFIG_HAS_FSL_DR_USB diff --git a/include/configs/M52277EVB.h b/include/configs/M52277EVB.h index 7f5eecaad5..3f7c1c9988 100644 --- a/include/configs/M52277EVB.h +++ b/include/configs/M52277EVB.h @@ -88,7 +88,6 @@ /* USB */ #ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI #define CONFIG_SYS_USB_EHCI_REGS_BASE 0xFC0B0000 #define CONFIG_SYS_USB_EHCI_CPU_INIT #endif diff --git a/include/configs/M54418TWR.h b/include/configs/M54418TWR.h index 1817571efe..7b162cccef 100644 --- a/include/configs/M54418TWR.h +++ b/include/configs/M54418TWR.h @@ -166,7 +166,6 @@ /* I2c */ #undef CONFIG_SYS_FSL_I2C -#undef CONFIG_HARD_I2C /* I2C with hardware support */ #undef CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ /* I2C speed and slave address */ #define CONFIG_SYS_I2C_SPEED 80000 diff --git a/include/configs/MPC8315ERDB.h b/include/configs/MPC8315ERDB.h index 493e3fa646..fbe033afb1 100644 --- a/include/configs/MPC8315ERDB.h +++ b/include/configs/MPC8315ERDB.h @@ -366,7 +366,6 @@ #define CONFIG_HAS_FSL_DR_USB #define CONFIG_SYS_SCCR_USBDRCM 3 -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_FSL #define CONFIG_USB_PHY_TYPE "utmi" #define CONFIG_EHCI_HCD_INIT_AFTER_RESET diff --git a/include/configs/MPC8349ITX.h b/include/configs/MPC8349ITX.h index 719c27966a..6d35d705ec 100644 --- a/include/configs/MPC8349ITX.h +++ b/include/configs/MPC8349ITX.h @@ -148,7 +148,6 @@ /* * Support USB */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_FSL /* Current USB implementation supports the only USB controller, diff --git a/include/configs/MPC837XEMDS.h b/include/configs/MPC837XEMDS.h index 85b7c48fdf..fcced0eb86 100644 --- a/include/configs/MPC837XEMDS.h +++ b/include/configs/MPC837XEMDS.h @@ -376,7 +376,6 @@ extern int board_pci_host_broken(void); #define CONFIG_PQ_MDS_PIB 1 /* PQ MDS Platform IO Board */ #define CONFIG_HAS_FSL_DR_USB 1 /* fixup device tree for the DR USB */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_FSL #define CONFIG_EHCI_HCD_INIT_AFTER_RESET diff --git a/include/configs/MPC837XERDB.h b/include/configs/MPC837XERDB.h index d39dc1b465..607b9266d2 100644 --- a/include/configs/MPC837XERDB.h +++ b/include/configs/MPC837XERDB.h @@ -651,7 +651,6 @@ #define CONFIG_ENV_OVERWRITE #define CONFIG_HAS_FSL_DR_USB -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_FSL #define CONFIG_EHCI_HCD_INIT_AFTER_RESET diff --git a/include/configs/MPC8536DS.h b/include/configs/MPC8536DS.h index aeb9f0bbaf..8375ead394 100644 --- a/include/configs/MPC8536DS.h +++ b/include/configs/MPC8536DS.h @@ -609,9 +609,7 @@ */ #define CONFIG_HAS_FSL_MPH_USB #ifdef CONFIG_HAS_FSL_MPH_USB -#define CONFIG_USB_EHCI - -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_USB_EHCI_FSL #endif diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h index 8f7e056606..b186e012d3 100644 --- a/include/configs/MPC8544DS.h +++ b/include/configs/MPC8544DS.h @@ -359,9 +359,8 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); /* * USB */ -#define CONFIG_USB_EHCI -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD #define CONFIG_USB_EHCI_PCI #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_PCI_EHCI_DEVICE 0 diff --git a/include/configs/MPC8572DS.h b/include/configs/MPC8572DS.h index e6aca11e50..2c1be228ee 100644 --- a/include/configs/MPC8572DS.h +++ b/include/configs/MPC8572DS.h @@ -559,9 +559,8 @@ /* * USB */ -#define CONFIG_USB_EHCI -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD #define CONFIG_USB_EHCI_PCI #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_PCI_EHCI_DEVICE 0 diff --git a/include/configs/P1010RDB.h b/include/configs/P1010RDB.h index 95b42208e9..867004fb48 100644 --- a/include/configs/P1010RDB.h +++ b/include/configs/P1010RDB.h @@ -670,9 +670,7 @@ extern unsigned long get_sdram_size(void); #define CONFIG_HAS_FSL_DR_USB #if defined(CONFIG_HAS_FSL_DR_USB) -#define CONFIG_USB_EHCI - -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_USB_EHCI_FSL #endif @@ -733,7 +731,7 @@ extern unsigned long get_sdram_size(void); #undef CONFIG_WATCHDOG /* watchdog disabled */ -#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) \ +#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI_HCD) \ || defined(CONFIG_FSL_SATA) #endif diff --git a/include/configs/P1022DS.h b/include/configs/P1022DS.h index db66c309e7..0763cf312e 100644 --- a/include/configs/P1022DS.h +++ b/include/configs/P1022DS.h @@ -606,9 +606,7 @@ */ #define CONFIG_HAS_FSL_DR_USB #ifdef CONFIG_HAS_FSL_DR_USB -#define CONFIG_USB_EHCI - -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_USB_EHCI_FSL #endif diff --git a/include/configs/P1023RDB.h b/include/configs/P1023RDB.h index 787b8d206e..8821be3410 100644 --- a/include/configs/P1023RDB.h +++ b/include/configs/P1023RDB.h @@ -253,9 +253,7 @@ extern unsigned long get_clock_freq(void); */ #define CONFIG_HAS_FSL_DR_USB #ifdef CONFIG_HAS_FSL_DR_USB -#define CONFIG_USB_EHCI - -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_USB_EHCI_FSL #endif diff --git a/include/configs/P2041RDB.h b/include/configs/P2041RDB.h index c3e3fae44f..7629fe8eb4 100644 --- a/include/configs/P2041RDB.h +++ b/include/configs/P2041RDB.h @@ -594,7 +594,6 @@ unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_HAS_FSL_MPH_USB #if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB) -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_FSL #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #endif diff --git a/include/configs/T102xQDS.h b/include/configs/T102xQDS.h index 4da829d838..42e692c4a0 100644 --- a/include/configs/T102xQDS.h +++ b/include/configs/T102xQDS.h @@ -637,7 +637,6 @@ unsigned long get_board_ddr_clk(void); #define CONFIG_HAS_FSL_DR_USB #ifdef CONFIG_HAS_FSL_DR_USB -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_FSL #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #endif diff --git a/include/configs/T102xRDB.h b/include/configs/T102xRDB.h index 3b55404cda..c2175bda34 100644 --- a/include/configs/T102xRDB.h +++ b/include/configs/T102xRDB.h @@ -641,7 +641,6 @@ unsigned long get_board_ddr_clk(void); #define CONFIG_HAS_FSL_DR_USB #ifdef CONFIG_HAS_FSL_DR_USB -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_FSL #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #endif diff --git a/include/configs/T1040QDS.h b/include/configs/T1040QDS.h index b2810b65f9..25658871e4 100644 --- a/include/configs/T1040QDS.h +++ b/include/configs/T1040QDS.h @@ -527,9 +527,7 @@ unsigned long get_board_ddr_clk(void); #define CONFIG_HAS_FSL_DR_USB #ifdef CONFIG_HAS_FSL_DR_USB -#define CONFIG_USB_EHCI - -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD #define CONFIG_USB_EHCI_FSL #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #endif diff --git a/include/configs/T104xRDB.h b/include/configs/T104xRDB.h index 5577408015..d2ece40d4a 100644 --- a/include/configs/T104xRDB.h +++ b/include/configs/T104xRDB.h @@ -637,9 +637,7 @@ $(SRCTREE)/board/freescale/t104xrdb/t1042d4_sd_rcw.cfg #define CONFIG_HAS_FSL_DR_USB #ifdef CONFIG_HAS_FSL_DR_USB -#define CONFIG_USB_EHCI - -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD #define CONFIG_USB_EHCI_FSL #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #endif diff --git a/include/configs/T208xQDS.h b/include/configs/T208xQDS.h index a32ddeed1d..02fd37d5cb 100644 --- a/include/configs/T208xQDS.h +++ b/include/configs/T208xQDS.h @@ -12,7 +12,6 @@ #define __T208xQDS_H #define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */ -#define CONFIG_USB_EHCI #if defined(CONFIG_ARCH_T2080) #define CONFIG_FSL_SATA_V2 #define CONFIG_SYS_SRIO /* Enable Serial RapidIO Support */ @@ -702,7 +701,7 @@ unsigned long get_board_ddr_clk(void); /* * USB */ -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD #define CONFIG_USB_EHCI_FSL #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_HAS_FSL_DR_USB diff --git a/include/configs/T208xRDB.h b/include/configs/T208xRDB.h index 90ce554035..faa1111e9f 100644 --- a/include/configs/T208xRDB.h +++ b/include/configs/T208xRDB.h @@ -12,7 +12,6 @@ #define __T2080RDB_H #define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */ -#define CONFIG_USB_EHCI #define CONFIG_FSL_SATA_V2 /* High Level Configuration Options */ @@ -652,7 +651,7 @@ unsigned long get_board_ddr_clk(void); /* * USB */ -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD #define CONFIG_USB_EHCI_FSL #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_HAS_FSL_DR_USB diff --git a/include/configs/T4240QDS.h b/include/configs/T4240QDS.h index 9d4baaa79f..5d030d1179 100644 --- a/include/configs/T4240QDS.h +++ b/include/configs/T4240QDS.h @@ -507,7 +507,6 @@ unsigned long get_board_ddr_clk(void); /* * USB */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_FSL #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_HAS_FSL_DR_USB diff --git a/include/configs/T4240RDB.h b/include/configs/T4240RDB.h index cc1f79940c..8ebfde19f9 100644 --- a/include/configs/T4240RDB.h +++ b/include/configs/T4240RDB.h @@ -685,7 +685,6 @@ unsigned long get_board_ddr_clk(void); /* * USB */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_FSL #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_HAS_FSL_DR_USB diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h index 13f4ef67e1..19e0b1be1b 100644 --- a/include/configs/TQM5200.h +++ b/include/configs/TQM5200.h @@ -124,8 +124,7 @@ #ifndef CONFIG_CAM5200 /* POST support */ #define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ - CONFIG_SYS_POST_CPU | \ - CONFIG_SYS_POST_I2C) + CONFIG_SYS_POST_CPU) #endif #ifdef CONFIG_POST @@ -144,7 +143,6 @@ /* * Command line configuration. */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_JFFS2 #define CONFIG_CMD_REGINFO @@ -279,54 +277,6 @@ #endif /* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#ifdef CONFIG_TQM5200_REV100 -#define CONFIG_SYS_I2C_MODULE 1 /* Select I2C module #1 for rev. 100 board */ -#else -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #2 for all other revs */ -#endif - -/* - * I2C clock frequency - * - * Please notice, that the resulting clock frequency could differ from the - * configured value. This is because the I2C clock is derived from system - * clock over a frequency divider with only a few divider values. U-Boot - * calculates the best approximation for CONFIG_SYS_I2C_SPEED. However the calculated - * approximation allways lies below the configured value, never above. - */ -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work - * also). For other EEPROMs configuration should be verified. On Mini-FAP the - * EEPROM (24C64) is on the same I2C address (but on other I2C bus), so the - * same configuration could be used. - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20 - -/* - * HW-Monitor configuration on Mini-FAP - */ -#if defined (CONFIG_MINIFAP) -#define CONFIG_SYS_I2C_HWMON_ADDR 0x2C -#endif - -/* List of I2C addresses to be verified by POST */ -#if defined (CONFIG_MINIFAP) -#undef CONFIG_SYS_POST_I2C_ADDRS -#define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_EEPROM_ADDR, \ - CONFIG_SYS_I2C_HWMON_ADDR, \ - CONFIG_SYS_I2C_SLAVE} -#endif - -/* * Flash configuration */ #define CONFIG_SYS_FLASH_BASE 0xFC000000 @@ -545,18 +495,6 @@ #endif /* - * RTC configuration - */ -#if defined (CONFIG_STK52XX) && !defined (CONFIG_STK52XX_REV100) -# define CONFIG_RTC_M41T11 1 -# define CONFIG_SYS_I2C_RTC_ADDR 0x68 -# define CONFIG_SYS_M41T11_BASE_YEAR 1900 /* because Linux uses the same base - year */ -#else -# define CONFIG_RTC_MPC5200 1 /* use internal MPC5200 RTC */ -#endif - -/* * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ diff --git a/include/configs/UCP1020.h b/include/configs/UCP1020.h index c60743acd0..cd46db4f6f 100644 --- a/include/configs/UCP1020.h +++ b/include/configs/UCP1020.h @@ -453,11 +453,9 @@ #define CONFIG_HAS_FSL_DR_USB #if defined(CONFIG_HAS_FSL_DR_USB) -#define CONFIG_USB_EHCI - #define CONFIG_USB_MAX_CONTROLLER_COUNT 1 -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_USB_EHCI_FSL #endif diff --git a/include/configs/a4m072.h b/include/configs/a4m072.h index 79099518e7..2ea43ffce1 100644 --- a/include/configs/a4m072.h +++ b/include/configs/a4m072.h @@ -81,7 +81,6 @@ /* * Command line configuration. */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_IDE #if defined(CONFIG_PCI) @@ -146,25 +145,6 @@ #undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ /* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ - -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 /* 1010010x */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 -#define CONFIG_SYS_EEPROM_WREN 1 -#define CONFIG_SYS_EEPROM_WP GPIO_PSC2_4 - -/* * Flash configuration */ #define CONFIG_SYS_FLASH_BASE 0xFE000000 diff --git a/include/configs/ac14xx.h b/include/configs/ac14xx.h index ee015bb83d..2a46e9b864 100644 --- a/include/configs/ac14xx.h +++ b/include/configs/ac14xx.h @@ -336,29 +336,12 @@ #define CONFIG_CMDLINE_EDITING 1 /* command line history */ -/* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_I2C_MULTI_BUS - -/* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 0x7F - /* * IIM - IC Identification Module */ #undef CONFIG_FSL_IIM /* - * EEPROM configuration for Atmel AT24C01: - * 8-bit addresses, 30ms write delay, 32-Byte Page Write Mode - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 30 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 - -/* * Ethernet configuration */ #define CONFIG_MPC512x_FEC 1 @@ -384,7 +367,6 @@ #define CONFIG_LOADS_ECHO 1 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 -#define CONFIG_CMD_EEPROM #undef CONFIG_CMD_FUSE #undef CONFIG_CMD_IDE #define CONFIG_CMD_JFFS2 diff --git a/include/configs/advantech_dms-ba16.h b/include/configs/advantech_dms-ba16.h index 52f8475669..b76f376a04 100644 --- a/include/configs/advantech_dms-ba16.h +++ b/include/configs/advantech_dms-ba16.h @@ -55,8 +55,6 @@ #define CONFIG_BOUNCE_BUFFER /* USB Configs */ -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MX6 #define CONFIG_USB_STORAGE #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET diff --git a/include/configs/alt.h b/include/configs/alt.h index d8a66f2d7d..16525087f1 100644 --- a/include/configs/alt.h +++ b/include/configs/alt.h @@ -81,7 +81,6 @@ #define CONFIG_SYS_I2C_POWERIC_ADDR 0x58 /* da9063 */ /* USB */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_RMOBILE #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 diff --git a/include/configs/am3517_crane.h b/include/configs/am3517_crane.h index 8be49af9f1..5de39cf740 100644 --- a/include/configs/am3517_crane.h +++ b/include/configs/am3517_crane.h @@ -16,9 +16,6 @@ /* * High Level Configuration Options */ -#define CONFIG_OMAP 1 /* in a TI OMAP core */ -#define CONFIG_OMAP3_AM3517CRANE 1 /* working with CRANEBOARD */ - #define CONFIG_EMIF4 /* The chip has EMIF4 controller */ #include <asm/arch/cpu.h> /* get chip and board defs */ diff --git a/include/configs/am3517_evm.h b/include/configs/am3517_evm.h index 7490f2b5ea..feb7b6eb97 100644 --- a/include/configs/am3517_evm.h +++ b/include/configs/am3517_evm.h @@ -13,10 +13,6 @@ #ifndef __CONFIG_H #define __CONFIG_H -/* High Level Configuration Options */ - -#define CONFIG_OMAP - #define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */ #define CONFIG_EMIF4 /* The chip has EMIF4 controller */ @@ -49,9 +45,6 @@ /* Hardware drivers */ -/* OMAP GPIO configuration */ -#define CONFIG_OMAP_GPIO - /* NS16550 Configuration */ #define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */ #define CONFIG_SYS_NS16550_SERIAL diff --git a/include/configs/ap_sh4a_4a.h b/include/configs/ap_sh4a_4a.h index 5f5882dc8e..d3d72b634d 100644 --- a/include/configs/ap_sh4a_4a.h +++ b/include/configs/ap_sh4a_4a.h @@ -35,20 +35,6 @@ #define CONFIG_BITBANGMII #define CONFIG_BITBANGMII_MULTI -/* I2C */ -#define CONFIG_SH_SH7734_I2C 1 -#define CONFIG_HARD_I2C 1 -#define CONFIG_I2C_MULTI_BUS 1 -#define CONFIG_SYS_MAX_I2C_BUS 2 -#define CONFIG_SYS_I2C_MODULE 0 -#define CONFIG_SYS_I2C_SPEED 400000 /* 400 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x50 -#define CONFIG_SH_I2C_DATA_HIGH 4 -#define CONFIG_SH_I2C_DATA_LOW 5 -#define CONFIG_SH_I2C_CLOCK 500000000 -#define CONFIG_SH_I2C_BASE0 0xFFC70000 -#define CONFIG_SH_I2C_BASE1 0xFFC71000 - /* undef to save memory */ #define CONFIG_SYS_LONGHELP /* Monitor Command Prompt */ diff --git a/include/configs/apalis-tk1.h b/include/configs/apalis-tk1.h index c6c956e1ee..2c49729caa 100644 --- a/include/configs/apalis-tk1.h +++ b/include/configs/apalis-tk1.h @@ -36,7 +36,6 @@ #define CONFIG_SYS_MMC_ENV_PART 1 /* USB host support */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_TEGRA /* PCI host support */ diff --git a/include/configs/apalis_t30.h b/include/configs/apalis_t30.h index e2acc6e8c9..cdb50cc28b 100644 --- a/include/configs/apalis_t30.h +++ b/include/configs/apalis_t30.h @@ -33,7 +33,6 @@ #define CONFIG_SYS_MMC_ENV_PART 1 /* USB host support */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_TEGRA /* PCI host support */ diff --git a/include/configs/apx4devkit.h b/include/configs/apx4devkit.h index a4c7847dab..cce39f27c7 100644 --- a/include/configs/apx4devkit.h +++ b/include/configs/apx4devkit.h @@ -79,12 +79,6 @@ #define CONFIG_USB_MAX_CONTROLLER_COUNT 1 #endif -/* RTC */ -#ifdef CONFIG_CMD_DATE -#define CONFIG_RTC_PCF8563 -#define CONFIG_SYS_I2C_RTC_ADDR 0x51 -#endif - /* Boot Linux */ #define CONFIG_BOOTFILE "uImage" #define CONFIG_BOOTCOMMAND "run bootcmd_nand" diff --git a/include/configs/aria.h b/include/configs/aria.h index 94f6605d46..4d946fc44a 100644 --- a/include/configs/aria.h +++ b/include/configs/aria.h @@ -340,32 +340,12 @@ #endif -/* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_I2C_MULTI_BUS - -/* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#if 0 -#define CONFIG_SYS_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */ -#endif - /* * IIM - IC Identification Module */ #undef CONFIG_FSL_IIM /* - * EEPROM configuration for Atmel AT24C32A-10TQ-2.7: - * 16-bit addresses, 10ms write delay, 32-Byte Page Write Mode - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 - -/* * Ethernet configuration */ #define CONFIG_MPC512x_FEC 1 @@ -392,7 +372,6 @@ #define CONFIG_LOADS_ECHO 1 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 -#define CONFIG_CMD_EEPROM #undef CONFIG_CMD_FUSE #undef CONFIG_CMD_IDE #define CONFIG_CMD_JFFS2 diff --git a/include/configs/aristainetos-common.h b/include/configs/aristainetos-common.h index 4d16d33585..7360e11ff1 100644 --- a/include/configs/aristainetos-common.h +++ b/include/configs/aristainetos-common.h @@ -202,8 +202,6 @@ #define CONFIG_RTC_M41T11 /* USB Configs */ -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MX6 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* For OTG port */ #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) diff --git a/include/configs/at91sam9x5ek.h b/include/configs/at91sam9x5ek.h index 52a051a137..a5489cd28c 100644 --- a/include/configs/at91sam9x5ek.h +++ b/include/configs/at91sam9x5ek.h @@ -51,7 +51,7 @@ #define CONFIG_CMD_NAND /* - * define CONFIG_USB_EHCI to enable USB Hi-Speed (aka 2.0) + * define CONFIG_USB_EHCI_HCD to enable USB Hi-Speed (aka 2.0) * NB: in this case, USB 1.1 devices won't be recognized. */ @@ -99,7 +99,7 @@ /* USB */ #ifdef CONFIG_CMD_USB -#ifndef CONFIG_USB_EHCI +#ifndef CONFIG_USB_EHCI_HCD #define CONFIG_USB_ATMEL #define CONFIG_USB_ATMEL_CLK_SEL_UPLL #define CONFIG_USB_OHCI_NEW diff --git a/include/configs/axs10x.h b/include/configs/axs10x.h index 768e8fbfa4..66e8cd5e9a 100644 --- a/include/configs/axs10x.h +++ b/include/configs/axs10x.h @@ -100,7 +100,7 @@ /* * Environment settings */ -#define CONFIG_ENV_IS_IN_EEPROM +#define CONFIG_ENV_IS_NOWHERE #define CONFIG_ENV_SIZE SZ_512 #define CONFIG_ENV_OFFSET 0 diff --git a/include/configs/beaver.h b/include/configs/beaver.h index cc32861169..f3d7a2fad2 100644 --- a/include/configs/beaver.h +++ b/include/configs/beaver.h @@ -39,7 +39,6 @@ #define CONFIG_SPI_FLASH_SIZE (4 << 20) /* USB Host support */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_TEGRA /* USB networking support */ diff --git a/include/configs/brppt1.h b/include/configs/brppt1.h index 0c1a54d7ba..521d097f8a 100644 --- a/include/configs/brppt1.h +++ b/include/configs/brppt1.h @@ -20,9 +20,6 @@ #define CONFIG_LCD_DT_SIMPLEFB #define LCD_BPP LCD_COLOR32 -#define CONFIG_HW_WATCHDOG -#define CONFIG_OMAP_WATCHDOG - /* Bootcount using the RTC block */ #define CONFIG_SYS_BOOTCOUNT_ADDR 0x44E3E000 #define CONFIG_BOOTCOUNT_LIMIT diff --git a/include/configs/brxre1.h b/include/configs/brxre1.h index 49f223a32a..99846890e0 100644 --- a/include/configs/brxre1.h +++ b/include/configs/brxre1.h @@ -21,7 +21,7 @@ #define CONFIG_VIDEO_BMP_GZIP #define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (1366*767*4) -#define CONFIG_BMP_24BMP +#define CONFIG_BMP_24BPP #define CONFIG_BMP_32BPP /* memory */ diff --git a/include/configs/bur_am335x_common.h b/include/configs/bur_am335x_common.h index 3742514a6e..7aad7ea51f 100644 --- a/include/configs/bur_am335x_common.h +++ b/include/configs/bur_am335x_common.h @@ -13,7 +13,6 @@ #define __BUR_AM335X_COMMON_H__ /* ------------------------------------------------------------------------- */ #define CONFIG_AM33XX -#define CONFIG_OMAP #define CONFIG_MAX_RAM_BANK_SIZE (1024 << 20) /* 1GB */ /* Timer information */ @@ -76,8 +75,6 @@ #define CONFIG_SYS_OMAP24_I2C_SPEED 100000 #define CONFIG_SYS_OMAP24_I2C_SLAVE 1 #define CONFIG_SYS_I2C_OMAP24XX -/* GPIO */ -#define CONFIG_OMAP_GPIO /* * Our platforms make use of SPL to initalize the hardware (primarily diff --git a/include/configs/cardhu.h b/include/configs/cardhu.h index e338f9bdd2..f1b5a71edf 100644 --- a/include/configs/cardhu.h +++ b/include/configs/cardhu.h @@ -43,7 +43,6 @@ #define CONFIG_SPI_FLASH_SIZE (4 << 20) /* USB Host support */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_TEGRA /* USB networking support */ diff --git a/include/configs/cei-tk1-som.h b/include/configs/cei-tk1-som.h index 8185926590..fd8df46776 100644 --- a/include/configs/cei-tk1-som.h +++ b/include/configs/cei-tk1-som.h @@ -38,7 +38,6 @@ #define CONFIG_SPI_FLASH_SIZE (4 << 20) /* USB Host support */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_TEGRA /* USB networking support */ diff --git a/include/configs/cgtqmx6eval.h b/include/configs/cgtqmx6eval.h index e05db3ed8a..cad1357f5c 100644 --- a/include/configs/cgtqmx6eval.h +++ b/include/configs/cgtqmx6eval.h @@ -61,8 +61,6 @@ #define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08 /* USB Configs */ -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MX6 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_USB_HOST_ETHER #define CONFIG_USB_ETHER_ASIX diff --git a/include/configs/cm5200.h b/include/configs/cm5200.h index 0073cb5373..3a7d826837 100644 --- a/include/configs/cm5200.h +++ b/include/configs/cm5200.h @@ -44,7 +44,7 @@ /* * POST support */ -#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | CONFIG_SYS_POST_CPU | CONFIG_SYS_POST_I2C) +#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | CONFIG_SYS_POST_CPU) #define MPC5XXX_SRAM_POST_SIZE (MPC5XXX_SRAM_SIZE - 4) /* List of I2C addresses to be verified by POST */ #define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_SLAVE, \ @@ -200,16 +200,6 @@ "-(config)" /* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #2 */ -#define CONFIG_SYS_I2C_SPEED 40000 /* 40 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x0 -#define CONFIG_SYS_I2C_IO 0x38 /* PCA9554AD I2C I/O port address */ -#define CONFIG_SYS_I2C_EEPROM 0x53 /* I2C EEPROM device address */ - -/* * RTC configuration */ #define CONFIG_RTC_MPC5200 1 /* use internal MPC5200 RTC */ diff --git a/include/configs/cm_t35.h b/include/configs/cm_t35.h index dfdad6c3d0..1898e3837d 100644 --- a/include/configs/cm_t35.h +++ b/include/configs/cm_t35.h @@ -22,8 +22,6 @@ /* * High Level Configuration Options */ -#define CONFIG_OMAP /* in a TI OMAP core */ -#define CONFIG_OMAP_GPIO #define CONFIG_CM_T3X /* working with CM-T35 and CM-T3730 */ #define CONFIG_SDRC /* The chip has SDRC controller */ @@ -77,8 +75,6 @@ /* USB */ #define CONFIG_USB_OMAP3 -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_OMAP #define CONFIG_USB_MUSB_UDC #define CONFIG_TWL4030_USB @@ -248,14 +244,7 @@ #define CONFIG_SPLASHIMAGE_GUARD -/* GPIO banks */ -#ifdef CONFIG_LED_STATUS -#define CONFIG_OMAP3_GPIO_6 /* GPIO186 is in GPIO bank 6 */ -#endif - /* Display Configuration */ -#define CONFIG_OMAP3_GPIO_2 -#define CONFIG_OMAP3_GPIO_5 #define CONFIG_VIDEO_OMAP3 #define LCD_BPP LCD_COLOR16 diff --git a/include/configs/cm_t3517.h b/include/configs/cm_t3517.h index e12dc020ff..0df7d4269c 100644 --- a/include/configs/cm_t3517.h +++ b/include/configs/cm_t3517.h @@ -13,7 +13,6 @@ /* * High Level Configuration Options */ -#define CONFIG_OMAP /* in a TI OMAP core */ #define CONFIG_CM_T3517 /* working with CM-T3517 */ #define CONFIG_SYS_TEXT_BASE 0x80008000 @@ -80,15 +79,11 @@ #define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\ 115200} -#define CONFIG_OMAP_GPIO - /* USB */ #define CONFIG_USB_MUSB_AM35X #ifndef CONFIG_USB_MUSB_AM35X #define CONFIG_USB_OMAP3 -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_OMAP #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 146 #define CONFIG_OMAP_EHCI_PHY2_RESET_GPIO 147 #else /* !CONFIG_USB_MUSB_AM35X */ @@ -250,14 +245,7 @@ /* Status LED */ #define GREEN_LED_GPIO 186 /* CM-T3517 Green LED is GPIO186 */ -/* GPIO banks */ -#ifdef CONFIG_LED_STATUS -#define CONFIG_OMAP3_GPIO_6 /* GPIO186 is in GPIO bank 6 */ -#endif - /* Display Configuration */ -#define CONFIG_OMAP3_GPIO_2 -#define CONFIG_OMAP3_GPIO_5 #define CONFIG_VIDEO_OMAP3 #define LCD_BPP LCD_COLOR16 diff --git a/include/configs/cm_t54.h b/include/configs/cm_t54.h index 477aa07bd8..ccaa568009 100644 --- a/include/configs/cm_t54.h +++ b/include/configs/cm_t54.h @@ -58,8 +58,6 @@ #define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \ CONFIG_SYS_SCSI_MAX_LUN) /* USB UHH support options */ -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_OMAP #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET @@ -86,9 +84,6 @@ #define CONFIG_USB_ETHER_ASIX #define CONFIG_USB_ETHER_MCS7830 -/* Max time to hold reset on this board, see doc/README.omap-reset-time */ -#define CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC 16296 - /* * Miscellaneous configurable options */ diff --git a/include/configs/colibri_t20.h b/include/configs/colibri_t20.h index 023e75cf33..03f6863169 100644 --- a/include/configs/colibri_t20.h +++ b/include/configs/colibri_t20.h @@ -25,7 +25,6 @@ #define CONFIG_SYS_I2C_TEGRA /* USB host support */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_TEGRA #define CONFIG_USB_MAX_CONTROLLER_COUNT 3 diff --git a/include/configs/colibri_t30.h b/include/configs/colibri_t30.h index bc1904418d..853cd52878 100644 --- a/include/configs/colibri_t30.h +++ b/include/configs/colibri_t30.h @@ -33,7 +33,6 @@ #define CONFIG_SYS_MMC_ENV_PART 1 /* USB host support */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_TEGRA /* USB networking support */ diff --git a/include/configs/colibri_vf.h b/include/configs/colibri_vf.h index c7f174839f..28383f49da 100644 --- a/include/configs/colibri_vf.h +++ b/include/configs/colibri_vf.h @@ -191,7 +191,6 @@ #endif /* USB Host Support */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_VF #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET diff --git a/include/configs/controlcenterd.h b/include/configs/controlcenterd.h index b52f300af9..7535ad5a62 100644 --- a/include/configs/controlcenterd.h +++ b/include/configs/controlcenterd.h @@ -291,7 +291,6 @@ /* * USB */ -#define CONFIG_USB_EHCI #define CONFIG_HAS_FSL_DR_USB #define CONFIG_USB_EHCI_FSL diff --git a/include/configs/corenet_ds.h b/include/configs/corenet_ds.h index f42ba795ea..7e606cd794 100644 --- a/include/configs/corenet_ds.h +++ b/include/configs/corenet_ds.h @@ -608,7 +608,6 @@ #define CONFIG_HAS_FSL_MPH_USB #if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB) -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_FSL #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #endif diff --git a/include/configs/corvus.h b/include/configs/corvus.h index bb1d0d7715..71b428f1f7 100644 --- a/include/configs/corvus.h +++ b/include/configs/corvus.h @@ -96,8 +96,6 @@ #define CONFIG_AT91_WANTS_COMMON_PHY /* USB */ -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_ATMEL #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 2 /* USB DFU support */ diff --git a/include/configs/cyrus.h b/include/configs/cyrus.h index 904da1a8ac..435929723b 100644 --- a/include/configs/cyrus.h +++ b/include/configs/cyrus.h @@ -426,7 +426,6 @@ #define CONFIG_HAS_FSL_MPH_USB #if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB) -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_FSL #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_EHCI_IS_TDI diff --git a/include/configs/dalmore.h b/include/configs/dalmore.h index f3ff9e7494..96a2df806a 100644 --- a/include/configs/dalmore.h +++ b/include/configs/dalmore.h @@ -35,7 +35,6 @@ #define CONFIG_SPI_FLASH_SIZE (4 << 20) /* USB Host support */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_TEGRA /* USB networking support */ diff --git a/include/configs/devkit8000.h b/include/configs/devkit8000.h index e72cee0c00..5884d5c67c 100644 --- a/include/configs/devkit8000.h +++ b/include/configs/devkit8000.h @@ -16,7 +16,6 @@ #define __CONFIG_H /* High Level Configuration Options */ -#define CONFIG_OMAP3_DEVKIT8000 1 /* working with DevKit8000 */ #define CONFIG_MACH_TYPE MACH_TYPE_DEVKIT8000 /* diff --git a/include/configs/digsy_mtc.h b/include/configs/digsy_mtc.h index 2b56945dd9..ab546c50cd 100644 --- a/include/configs/digsy_mtc.h +++ b/include/configs/digsy_mtc.h @@ -85,7 +85,6 @@ /* * Command line configuration. */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_IDE #define CONFIG_CMD_IRQ #define CONFIG_CMD_PCI @@ -206,36 +205,6 @@ #define CONFIG_BOOTCOMMAND "run mtcb_start" /* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_MODULE 1 -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70 - -/* - * RTC configuration - */ -#if defined(CONFIG_DIGSY_REV5) -#define CONFIG_SYS_I2C_RTC_ADDR 0x56 -#define CONFIG_RTC_RV3029 -/* Enable 5k Ohm trickle charge resistor */ -#define CONFIG_SYS_RV3029_TCR 0x20 -#else -#define CONFIG_RTC_DS1337 -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 -#define CONFIG_SYS_DS1339_TCR_VAL 0xAB /* diode + 4k resistor */ -#endif - -/* * Flash configuration */ #define CONFIG_SYS_FLASH_CFI 1 diff --git a/include/configs/draco.h b/include/configs/draco.h index 896d14f99a..ba6a43062a 100644 --- a/include/configs/draco.h +++ b/include/configs/draco.h @@ -45,9 +45,6 @@ #define CONFIG_FACTORYSET -/* Watchdog */ -#define CONFIG_OMAP_WATCHDOG - /* Define own nand partitions */ #define CONFIG_ENV_OFFSET_REDUND 0x2E0000 #define CONFIG_ENV_SIZE_REDUND 0x2000 diff --git a/include/configs/ds414.h b/include/configs/ds414.h index d1d4bf0156..2c83a716a3 100644 --- a/include/configs/ds414.h +++ b/include/configs/ds414.h @@ -74,8 +74,6 @@ #endif #if !defined(CONFIG_USB_XHCI_HCD) -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MARVELL #define CONFIG_EHCI_IS_TDI #endif diff --git a/include/configs/duovero.h b/include/configs/duovero.h index 4bb81e5d9c..f142231689 100644 --- a/include/configs/duovero.h +++ b/include/configs/duovero.h @@ -25,8 +25,6 @@ #define CONFIG_SYS_DEFAULT_LPDDR2_TIMINGS /* USB UHH support options */ -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_OMAP #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 1 diff --git a/include/configs/e2220-1170.h b/include/configs/e2220-1170.h index b6a758f0b2..f88045436f 100644 --- a/include/configs/e2220-1170.h +++ b/include/configs/e2220-1170.h @@ -33,7 +33,6 @@ #define CONFIG_SPI_FLASH_SIZE (4 << 20) /* USB2.0 Host support */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_TEGRA /* USB networking support */ diff --git a/include/configs/eco5pk.h b/include/configs/eco5pk.h index 03cc74c596..3d7a168bc4 100644 --- a/include/configs/eco5pk.h +++ b/include/configs/eco5pk.h @@ -15,8 +15,6 @@ #include "tam3517-common.h" -#undef CONFIG_USB_EHCI -#undef CONFIG_USB_EHCI_OMAP #undef CONFIG_USB_OMAP3 /* Our console port is port3 */ diff --git a/include/configs/edminiv2.h b/include/configs/edminiv2.h index f7ac3027dd..d1c7b937e3 100644 --- a/include/configs/edminiv2.h +++ b/include/configs/edminiv2.h @@ -171,8 +171,6 @@ * Common USB/EHCI configuration */ #ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI /* Enable EHCI USB support */ -#define CONFIG_USB_EHCI_MARVELL #define ORION5X_USB20_HOST_PORT_BASE ORION5X_USB20_PORT0_BASE #define CONFIG_SUPPORT_VFAT #endif /* CONFIG_CMD_USB */ diff --git a/include/configs/embestmx6boards.h b/include/configs/embestmx6boards.h index 68d48b2e6a..749a9e3bc1 100644 --- a/include/configs/embestmx6boards.h +++ b/include/configs/embestmx6boards.h @@ -35,8 +35,6 @@ #define CONFIG_SYS_I2C_SPEED 100000 /* USB Configs */ -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MX6 #define CONFIG_USB_HOST_ETHER #define CONFIG_USB_ETHER_ASIX #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 diff --git a/include/configs/etamin.h b/include/configs/etamin.h index 40c57948cc..a0152a4a43 100644 --- a/include/configs/etamin.h +++ b/include/configs/etamin.h @@ -116,9 +116,6 @@ #define CONFIG_SYS_DCACHE_OFF #endif -/* Watchdog */ -#define CONFIG_OMAP_WATCHDOG - /* Define own nand partitions */ #define CONFIG_ENV_OFFSET_REDUND 0xB80000 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE diff --git a/include/configs/exynos5250-common.h b/include/configs/exynos5250-common.h index aee9fea9da..8e8cdf359b 100644 --- a/include/configs/exynos5250-common.h +++ b/include/configs/exynos5250-common.h @@ -26,7 +26,6 @@ #define CONFIG_SYS_INIT_SP_ADDR CONFIG_IRAM_STACK /* USB */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_EXYNOS #define CONFIG_USB_XHCI_EXYNOS diff --git a/include/configs/ge_bx50v3.h b/include/configs/ge_bx50v3.h index 776910c6cd..198259b3c0 100644 --- a/include/configs/ge_bx50v3.h +++ b/include/configs/ge_bx50v3.h @@ -68,8 +68,6 @@ /* USB Configs */ #ifdef CONFIG_USB -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MX6 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) diff --git a/include/configs/gose.h b/include/configs/gose.h index 8956841fbe..8a1d6d3407 100644 --- a/include/configs/gose.h +++ b/include/configs/gose.h @@ -78,7 +78,6 @@ #define CONFIG_SYS_I2C_POWERIC_ADDR 0x58 /* da9063 */ /* USB */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_RMOBILE #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 diff --git a/include/configs/gplugd.h b/include/configs/gplugd.h index 3ec7649a1d..f2260eae56 100644 --- a/include/configs/gplugd.h +++ b/include/configs/gplugd.h @@ -82,7 +82,6 @@ #define CONFIG_ENV_SIZE 0x4000 #ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_ARMADA100 #define CONFIG_EHCI_IS_TDI #endif /* CONFIG_CMD_USB */ diff --git a/include/configs/gw_ventana.h b/include/configs/gw_ventana.h index 92eded6cda..1c18a380fe 100644 --- a/include/configs/gw_ventana.h +++ b/include/configs/gw_ventana.h @@ -156,8 +156,6 @@ #define CONFIG_ARP_TIMEOUT 200UL /* USB Configs */ -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MX6 #define CONFIG_USB_HOST_ETHER #define CONFIG_USB_ETHER_ASIX #define CONFIG_USB_ETHER_SMSC95XX diff --git a/include/configs/harmony.h b/include/configs/harmony.h index 1a5d4b1dd5..c17d7fad79 100644 --- a/include/configs/harmony.h +++ b/include/configs/harmony.h @@ -36,7 +36,6 @@ #define CONFIG_ENV_OFFSET (SZ_512M - SZ_128K) /* 128K sector size */ /* USB Host support */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_TEGRA /* USB networking support */ diff --git a/include/configs/ids8313.h b/include/configs/ids8313.h index 6b6bbbd5c0..7ffc9d1dd9 100644 --- a/include/configs/ids8313.h +++ b/include/configs/ids8313.h @@ -165,7 +165,6 @@ #define CONFIG_TSEC2 #define CONFIG_TSEC_ENET #define CONFIG_HARD_SPI -#define CONFIG_HARD_I2C /* * NOR FLASH setup diff --git a/include/configs/ipek01.h b/include/configs/ipek01.h index aff4adf5d0..ece72c6aa1 100644 --- a/include/configs/ipek01.h +++ b/include/configs/ipek01.h @@ -150,29 +150,6 @@ #define OF_SOC "soc5200@f0000000" #define OF_TBCLK (bd->bi_busfreq / 4) -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ - -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x53 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 - -/* - * RTC configuration - */ -#define CONFIG_RTC_PCF8563 -#define CONFIG_SYS_I2C_RTC_ADDR 0x51 - #define CONFIG_SYS_FLASH_BASE 0xFC000000 #define CONFIG_SYS_FLASH_SIZE 0x01000000 #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + \ diff --git a/include/configs/jetson-tk1.h b/include/configs/jetson-tk1.h index b31ba6a4ee..89f6cbc85b 100644 --- a/include/configs/jetson-tk1.h +++ b/include/configs/jetson-tk1.h @@ -34,7 +34,6 @@ #define CONFIG_SPI_FLASH_SIZE (4 << 20) /* USB Host support */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_TEGRA /* USB networking support */ diff --git a/include/configs/jupiter.h b/include/configs/jupiter.h index 0d97317c7f..4461623118 100644 --- a/include/configs/jupiter.h +++ b/include/configs/jupiter.h @@ -127,25 +127,6 @@ #define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000" #endif -#if 0 -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ - -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70 -#endif - /* * Flash configuration */ diff --git a/include/configs/kc1.h b/include/configs/kc1.h index 85bc0e3fb7..343685a652 100644 --- a/include/configs/kc1.h +++ b/include/configs/kc1.h @@ -24,13 +24,6 @@ #define CONFIG_SYS_PL310_BASE 0x48242000 /* - * Platform - */ - -#define CONFIG_OMAP -#define CONFIG_OMAP4430 - -/* * Board */ @@ -61,12 +54,6 @@ #define CONFIG_SYS_MALLOC_LEN (1024 * 1024 + CONFIG_ENV_SIZE) /* - * GPIO - */ - -#define CONFIG_OMAP_GPIO - -/* * I2C */ diff --git a/include/configs/koelsch.h b/include/configs/koelsch.h index 1ca564f983..2166e2c8f2 100644 --- a/include/configs/koelsch.h +++ b/include/configs/koelsch.h @@ -78,7 +78,6 @@ #define CONFIG_SYS_I2C_POWERIC_ADDR 0x58 /* da9063 */ /* USB */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_RMOBILE #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 diff --git a/include/configs/lager.h b/include/configs/lager.h index b619d153c9..bf1352d941 100644 --- a/include/configs/lager.h +++ b/include/configs/lager.h @@ -80,7 +80,6 @@ #define CONFIG_SYS_TMU_CLK_DIV 4 /* USB */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_RMOBILE #define CONFIG_USB_MAX_CONTROLLER_COUNT 3 diff --git a/include/configs/liteboard.h b/include/configs/liteboard.h index 2294106802..016d54f138 100644 --- a/include/configs/liteboard.h +++ b/include/configs/liteboard.h @@ -137,8 +137,6 @@ /* USB Configs */ #ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MX6 #define CONFIG_USB_STORAGE #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) diff --git a/include/configs/ls1012aqds.h b/include/configs/ls1012aqds.h index 8d7e54305d..2b3833d61b 100644 --- a/include/configs/ls1012aqds.h +++ b/include/configs/ls1012aqds.h @@ -115,7 +115,6 @@ /*#define CONFIG_HAS_FSL_DR_USB*/ #ifdef CONFIG_HAS_FSL_DR_USB -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_FSL #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #endif diff --git a/include/configs/ls1021aqds.h b/include/configs/ls1021aqds.h index 373de40d29..333bb26623 100644 --- a/include/configs/ls1021aqds.h +++ b/include/configs/ls1021aqds.h @@ -402,7 +402,6 @@ unsigned long get_board_ddr_clk(void); /*#define CONFIG_HAS_FSL_DR_USB*/ #ifdef CONFIG_HAS_FSL_DR_USB -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_FSL #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #endif diff --git a/include/configs/ls1021atwr.h b/include/configs/ls1021atwr.h index 1ff3d9ee9e..81f38a30a4 100644 --- a/include/configs/ls1021atwr.h +++ b/include/configs/ls1021atwr.h @@ -40,7 +40,6 @@ /*#define CONFIG_HAS_FSL_DR_USB*/ #ifdef CONFIG_HAS_FSL_DR_USB -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_FSL #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #endif diff --git a/include/configs/lwmon5.h b/include/configs/lwmon5.h index 911192da7a..6893bf24ff 100644 --- a/include/configs/lwmon5.h +++ b/include/configs/lwmon5.h @@ -362,7 +362,6 @@ /* * USB/EHCI */ -#define CONFIG_USB_EHCI /* Enable EHCI USB support */ #define CONFIG_USB_EHCI_PPC4XX /* on PPC4xx platform */ #define CONFIG_SYS_PPC4XX_USB_ADDR 0xe0000300 #define CONFIG_EHCI_MMIO_BIG_ENDIAN diff --git a/include/configs/m28evk.h b/include/configs/m28evk.h index f6fa599e6b..c4717238bb 100644 --- a/include/configs/m28evk.h +++ b/include/configs/m28evk.h @@ -16,7 +16,6 @@ /* U-Boot Commands */ #define CONFIG_FAT_WRITE -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_NAND #define CONFIG_CMD_NAND_TRIMFFS @@ -63,11 +62,6 @@ #define CONFIG_FEC_MXC #endif -/* EEPROM */ -#ifdef CONFIG_CMD_EEPROM -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#endif - /* RTC */ #ifdef CONFIG_CMD_DATE /* Use the internal RTC in the MXS chip */ diff --git a/include/configs/m53evk.h b/include/configs/m53evk.h index d85de5fa17..c729e0938f 100644 --- a/include/configs/m53evk.h +++ b/include/configs/m53evk.h @@ -162,7 +162,6 @@ * USB */ #ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_MX5 #define CONFIG_USB_HOST_ETHER #define CONFIG_USB_ETHER_ASIX diff --git a/include/configs/ma5d4evk.h b/include/configs/ma5d4evk.h index db58f735bc..8413c5c234 100644 --- a/include/configs/ma5d4evk.h +++ b/include/configs/ma5d4evk.h @@ -102,8 +102,6 @@ * USB */ #ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_ATMEL #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 /* USB device */ diff --git a/include/configs/manroland/mpc5200-common.h b/include/configs/manroland/mpc5200-common.h new file mode 100644 index 0000000000..68874dc029 --- /dev/null +++ b/include/configs/manroland/mpc5200-common.h @@ -0,0 +1,176 @@ +/* + * (C) Copyright 2009 + * Heiko Schocher, DENX Software Engineering, hs@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __MANROLAND_MPC52XX__COMMON_H +#define __MANROLAND_MPC52XX__COMMON_H + +/* + * High Level Configuration Options + * (easy to change) + */ +#define CONFIG_MPC5200 1 /* MPC5200 CPU */ + +/* ... running at 33.000000MHz */ +#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 + +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + +/* + * Serial console configuration + */ +#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200,\ + 230400 } + +#if (CONFIG_SYS_TEXT_BASE == 0xFFF00000) /* Boot low */ +# define CONFIG_SYS_LOWBOOT 1 +#endif + +/* + * IPB Bus clocking configuration. + */ +#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ + +/* + * Flash configuration + */ +#define CONFIG_SYS_FLASH_BASE 0xFF800000 + +#define CONFIG_SYS_FLASH_SIZE 0x00800000 /* 8 MByte */ + +#define CONFIG_ENV_ADDR (CONFIG_SYS_TEXT_BASE+0x40000) /* second sector */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks + (= chip selects) */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout [ms]*/ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout [ms]*/ + +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_CFI_AMD_RESET + +/* + * Environment settings + */ +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_SIZE 0x4000 +#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) + +/* + * Memory map + */ +#define CONFIG_SYS_MBAR 0xF0000000 +#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 + +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE -\ + GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SRAM_BASE 0x80100000 /* CS 1 */ +#define CONFIG_SYS_DISPLAY_BASE 0x80600000 /* CS 3 */ + +/* Settings for XLB = 132 MHz */ +#define SDRAM_DDR 1 +#define SDRAM_MODE 0x018D0000 +#define SDRAM_EMODE 0x40090000 +#define SDRAM_CONTROL 0x714f0f00 +#define SDRAM_CONFIG1 0x73722930 +#define SDRAM_CONFIG2 0x47770000 +#define SDRAM_TAPDELAY 0x10000000 + +/* Use ON-Chip SRAM until RAM will be available */ +#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM +#ifdef CONFIG_POST +/* preserve space for the post_word at end of on-chip SRAM */ +#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_POST_SIZE +#else +#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE +#endif + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +# define CONFIG_SYS_RAMBOOT 1 +#endif + +#define CONFIG_SYS_MONITOR_LEN (192 << 10) +#define CONFIG_SYS_MALLOC_LEN (512 << 10) +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) + +/* + * Ethernet configuration + */ +#define CONFIG_MPC5xxx_FEC 1 +#define CONFIG_MPC5xxx_FEC_MII100 +#define CONFIG_PHY_ADDR 0x00 +#define CONFIG_MII 1 + +/*use Hardware WDT */ +#define CONFIG_HW_WATCHDOG + +#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ +#if defined(CONFIG_CMD_KGDB) +# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/* + * Various low-level settings + */ +#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI +#define CONFIG_SYS_HID0_FINAL HID0_ICE + +#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE +#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE + +/* 8Mbit SRAM @0x80100000 */ +#define CONFIG_SYS_CS1_START CONFIG_SYS_SRAM_BASE + +#define CONFIG_SYS_CS_BURST 0x00000000 +#define CONFIG_SYS_CS_DEADCYCLE 0x33333333 + +/*----------------------------------------------------------------------- + * IDE/ATA stuff Supports IDE harddisk + *----------------------------------------------------------------------- + */ + +#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ + +#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ +#undef CONFIG_IDE_LED /* LED for ide not supported */ + +#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ + +#define CONFIG_IDE_PREINIT 1 + +#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 + +#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA + +/* Offset for data I/O */ +#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) + +/* Offset for normal register accesses */ +#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) + +/* Offset for alternate registers */ +#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) + +/* Interval between registers */ +#define CONFIG_SYS_ATA_STRIDE 4 + +#define CONFIG_ATAPI 1 + +#define OF_CPU "PowerPC,5200@0" +#define OF_SOC "soc5200@f0000000" +#define OF_TBCLK (bd->bi_busfreq / 4) +#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000" +#define CONFIG_OF_IDE_FIXUP + +#endif /* __MANROLAND_MPC52XX__COMMON_H */ diff --git a/include/configs/mccmon6.h b/include/configs/mccmon6.h index 9e5c29f92f..4b9b5312bf 100644 --- a/include/configs/mccmon6.h +++ b/include/configs/mccmon6.h @@ -98,8 +98,6 @@ "128k@0x19C0000(swupdate-kernel-dtb.nor)" /* USB Configs */ -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MX6 #define CONFIG_USB_STORAGE #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) diff --git a/include/configs/mcx.h b/include/configs/mcx.h index e4f2a02dcf..c70e68c5b0 100644 --- a/include/configs/mcx.h +++ b/include/configs/mcx.h @@ -12,9 +12,6 @@ /* * High Level Configuration Options */ -#define CONFIG_OMAP /* in a TI OMAP core */ -#define CONFIG_OMAP3_MCX /* working with mcx */ -#define CONFIG_OMAP_GPIO #define CONFIG_MACH_TYPE MACH_TYPE_MCX @@ -76,10 +73,6 @@ 115200} /* EHCI */ -#define CONFIG_OMAP3_GPIO_2 -#define CONFIG_OMAP3_GPIO_5 -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_OMAP #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 57 #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 #define CONFIG_USB_HOST_ETHER diff --git a/include/configs/mecp5123.h b/include/configs/mecp5123.h index 1a9cb675df..fe94e663c5 100644 --- a/include/configs/mecp5123.h +++ b/include/configs/mecp5123.h @@ -241,27 +241,12 @@ #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -/* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed */ -#define CONFIG_SYS_I2C_SLAVE 0x7F /* slave address */ - /* * IIM - IC Identification Module */ #undef CONFIG_FSL_IIM /* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* 16-bit EEPROM address */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* Atmel: AT24C32A-10TQ-2.7 */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* 10ms of delay */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* 32-Byte Page Write Mode */ -#define CONFIG_SYS_EEPROM_WREN /* Use EEPROM write protect */ - -/* * Ethernet configuration */ #define CONFIG_MPC512x_FEC 1 @@ -280,7 +265,7 @@ /* * Environment */ -#define CONFIG_ENV_IS_IN_EEPROM /* Store env in I2C EEPROM */ +#define CONFIG_ENV_IS_NOWHERE /* Store env in I2C EEPROM */ #define CONFIG_ENV_SIZE 0x1000 #define CONFIG_ENV_OFFSET 0x0000 /* environment starts here */ @@ -288,7 +273,6 @@ #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ #define CONFIG_CMD_REGINFO -#define CONFIG_CMD_EEPROM #undef CONFIG_CMD_FUSE #undef CONFIG_CMD_IDE #define CONFIG_CMD_JFFS2 diff --git a/include/configs/medcom-wide.h b/include/configs/medcom-wide.h index b9b666fd3e..d2165828d3 100644 --- a/include/configs/medcom-wide.h +++ b/include/configs/medcom-wide.h @@ -29,7 +29,6 @@ #define CONFIG_ENV_OFFSET (SZ_512M - SZ_128K) /* 128K sectors */ /* USB host support */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_TEGRA /* USB networking support */ diff --git a/include/configs/motionpro.h b/include/configs/motionpro.h index 136db0dd26..cb5c346807 100644 --- a/include/configs/motionpro.h +++ b/include/configs/motionpro.h @@ -34,7 +34,6 @@ * Command line configuration. */ #define CONFIG_CMD_DTT -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_IDE #define CONFIG_CMD_IMMAP #define CONFIG_CMD_JFFS2 @@ -256,21 +255,6 @@ #define CONFIG_SYS_ATA_STRIDE 4 /* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 2 /* select I2C module #2 */ -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 1 /* 2 bytes per write cycle */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 /* 2ms/cycle + 3ms extra */ - -/* * RTC configuration */ #define CONFIG_RTC_DS1337 1 @@ -284,12 +268,6 @@ #define LED_ON 0x00000010 /* - * Temperature sensor - */ -#define CONFIG_DTT_LM75 1 -#define CONFIG_DTT_SENSORS { 0x49 } - -/* * Environment settings */ #define CONFIG_ENV_IS_IN_FLASH 1 diff --git a/include/configs/mpc5121ads.h b/include/configs/mpc5121ads.h index dafb724e3f..7919320c88 100644 --- a/include/configs/mpc5121ads.h +++ b/include/configs/mpc5121ads.h @@ -327,29 +327,12 @@ #endif -/* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#if 0 -#define CONFIG_SYS_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */ -#endif - /* * IIM - IC Identification Module */ #undef CONFIG_FSL_IIM /* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* 16-bit EEPROM address */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* Atmel: AT24C32A-10TQ-2.7 */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* 10ms of delay */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* 32-Byte Page Write Mode */ - -/* * Ethernet configuration */ #define CONFIG_MPC512x_FEC 1 @@ -369,7 +352,6 @@ */ #if defined(CONFIG_CMD_USB) -#define CONFIG_USB_EHCI /* Enable EHCI Support */ #define CONFIG_USB_EHCI_FSL /* On a FSL platform */ #define CONFIG_EHCI_MMIO_BIG_ENDIAN /* With big-endian regs */ #define CONFIG_EHCI_DESC_BIG_ENDIAN @@ -396,7 +378,6 @@ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_IDE #define CONFIG_CMD_JFFS2 #define CONFIG_CMD_REGINFO diff --git a/include/configs/mt_ventoux.h b/include/configs/mt_ventoux.h index dfebde20ec..2e373175dc 100644 --- a/include/configs/mt_ventoux.h +++ b/include/configs/mt_ventoux.h @@ -24,7 +24,6 @@ #define CONFIG_BOOTFILE "uImage" #define CONFIG_AUTO_COMPLETE -#define CONFIG_OMAP3_GPIO_4 #define CONFIG_HOSTNAME mt_ventoux /* diff --git a/include/configs/mv-common.h b/include/configs/mv-common.h index 814f0dd7ca..d000d7617a 100644 --- a/include/configs/mv-common.h +++ b/include/configs/mv-common.h @@ -121,7 +121,6 @@ * Common USB/EHCI configuration */ #if defined(CONFIG_CMD_USB) && !defined(CONFIG_DM) -#define CONFIG_USB_EHCI /* Enable EHCI USB support */ #define CONFIG_SUPPORT_VFAT #endif /* CONFIG_CMD_USB */ diff --git a/include/configs/mx35pdk.h b/include/configs/mx35pdk.h index 79d92bb06a..e60b96f7dc 100644 --- a/include/configs/mx35pdk.h +++ b/include/configs/mx35pdk.h @@ -199,7 +199,6 @@ #define CONFIG_SYS_NAND_LARGEPAGE /* EHCI driver */ -#define CONFIG_USB_EHCI #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 1 #define CONFIG_EHCI_IS_TDI #define CONFIG_EHCI_HCD_INIT_AFTER_RESET diff --git a/include/configs/mx51evk.h b/include/configs/mx51evk.h index dfd7ea9d45..54bc563467 100644 --- a/include/configs/mx51evk.h +++ b/include/configs/mx51evk.h @@ -73,7 +73,6 @@ #define CONFIG_FEC_MXC_PHYADDR 0x1F /* USB Configs */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_MX5 #define CONFIG_USB_HOST_ETHER #define CONFIG_USB_ETHER_ASIX diff --git a/include/configs/mx53cx9020.h b/include/configs/mx53cx9020.h index 3094402d15..151c4b3faf 100644 --- a/include/configs/mx53cx9020.h +++ b/include/configs/mx53cx9020.h @@ -45,7 +45,6 @@ #define CONFIG_FEC_MXC_PHYADDR 0x1F /* USB Configs */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_MX5 #define CONFIG_USB_STORAGE #define CONFIG_USB_HOST_ETHER diff --git a/include/configs/mx53loco.h b/include/configs/mx53loco.h index 945be5835b..1b6d868d04 100644 --- a/include/configs/mx53loco.h +++ b/include/configs/mx53loco.h @@ -42,7 +42,6 @@ #define CONFIG_FEC_MXC_PHYADDR 0x1F /* USB Configs */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_MX5 #define CONFIG_USB_HOST_ETHER #define CONFIG_USB_ETHER_ASIX diff --git a/include/configs/mx6cuboxi.h b/include/configs/mx6cuboxi.h index 84fdf656cd..b2cecc5d0e 100644 --- a/include/configs/mx6cuboxi.h +++ b/include/configs/mx6cuboxi.h @@ -44,8 +44,6 @@ #define CONFIG_IMX_VIDEO_SKIP /* USB */ -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MX6 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) #define CONFIG_MXC_USB_FLAGS 0 diff --git a/include/configs/mx6qarm2.h b/include/configs/mx6qarm2.h index 9f42735571..de5dc1c451 100644 --- a/include/configs/mx6qarm2.h +++ b/include/configs/mx6qarm2.h @@ -128,8 +128,6 @@ /* USB Configs */ #ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MX6 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_USB_HOST_ETHER #define CONFIG_USB_ETHER_ASIX diff --git a/include/configs/mx6qsabreauto.h b/include/configs/mx6qsabreauto.h index ef7675c688..635c04acf9 100644 --- a/include/configs/mx6qsabreauto.h +++ b/include/configs/mx6qsabreauto.h @@ -15,8 +15,6 @@ #define CONFIG_MMCROOT "/dev/mmcblk0p2" /* USB Configs */ -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MX6 #define CONFIG_USB_HOST_ETHER #define CONFIG_USB_ETHER_ASIX #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 diff --git a/include/configs/mx6sabresd.h b/include/configs/mx6sabresd.h index 598ab9aa2e..a8c0e03582 100644 --- a/include/configs/mx6sabresd.h +++ b/include/configs/mx6sabresd.h @@ -63,8 +63,6 @@ /* USB Configs */ #ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MX6 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_USB_HOST_ETHER #define CONFIG_USB_ETHER_ASIX diff --git a/include/configs/mx6slevk.h b/include/configs/mx6slevk.h index 2fff7995ea..6ab76bb8fa 100644 --- a/include/configs/mx6slevk.h +++ b/include/configs/mx6slevk.h @@ -159,8 +159,6 @@ /* USB Configs */ #ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MX6 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_USB_HOST_ETHER #define CONFIG_USB_ETHER_ASIX diff --git a/include/configs/mx6sxsabreauto.h b/include/configs/mx6sxsabreauto.h index 971f6c2f31..3e73dad9a3 100644 --- a/include/configs/mx6sxsabreauto.h +++ b/include/configs/mx6sxsabreauto.h @@ -149,8 +149,6 @@ #define CONFIG_PHY_ATHEROS #ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MX6 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_USB_HOST_ETHER #define CONFIG_USB_ETHER_ASIX diff --git a/include/configs/mx6sxsabresd.h b/include/configs/mx6sxsabresd.h index dafa946e47..b39ab729d8 100644 --- a/include/configs/mx6sxsabresd.h +++ b/include/configs/mx6sxsabresd.h @@ -167,8 +167,6 @@ #define CONFIG_PHY_ATHEROS #ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MX6 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_USB_HOST_ETHER #define CONFIG_USB_ETHER_ASIX diff --git a/include/configs/mx6ul_14x14_evk.h b/include/configs/mx6ul_14x14_evk.h index 240d3a226c..2c40decf49 100644 --- a/include/configs/mx6ul_14x14_evk.h +++ b/include/configs/mx6ul_14x14_evk.h @@ -186,8 +186,6 @@ /* USB Configs */ #ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MX6 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) #define CONFIG_MXC_USB_FLAGS 0 diff --git a/include/configs/mxs.h b/include/configs/mxs.h index fdf596f82f..041dcde38e 100644 --- a/include/configs/mxs.h +++ b/include/configs/mxs.h @@ -126,16 +126,6 @@ #endif #endif -/* I2C */ -#ifdef CONFIG_CMD_I2C -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_MXS -#define CONFIG_HARD_I2C -#ifndef CONFIG_SYS_I2C_SPEED -#define CONFIG_SYS_I2C_SPEED 400000 -#endif -#endif - /* LCD */ #ifdef CONFIG_VIDEO #define CONFIG_VIDEO_MXS @@ -168,7 +158,6 @@ /* USB */ #ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_MXS #define CONFIG_EHCI_IS_TDI #endif diff --git a/include/configs/nas220.h b/include/configs/nas220.h index 861cb5df57..7004176c4a 100644 --- a/include/configs/nas220.h +++ b/include/configs/nas220.h @@ -94,7 +94,6 @@ * USB/EHCI */ #ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI /* Enable EHCI USB support */ #define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */ #define CONFIG_EHCI_IS_TDI #define CONFIG_SUPPORT_VFAT diff --git a/include/configs/nitrogen6x.h b/include/configs/nitrogen6x.h index cacc1b81f0..13625286c5 100644 --- a/include/configs/nitrogen6x.h +++ b/include/configs/nitrogen6x.h @@ -74,8 +74,6 @@ #define CONFIG_PHY_MICREL_KSZ9021 /* USB Configs */ -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MX6 #define CONFIG_USB_HOST_ETHER #define CONFIG_USB_ETHER_ASIX #define CONFIG_USB_ETHER_MCS7830 diff --git a/include/configs/nokia_rx51.h b/include/configs/nokia_rx51.h index f51bfc34c1..5e2d5991e7 100644 --- a/include/configs/nokia_rx51.h +++ b/include/configs/nokia_rx51.h @@ -22,10 +22,6 @@ /* * High Level Configuration Options */ - -#define CONFIG_OMAP /* in a TI OMAP core */ -#define CONFIG_OMAP3430 /* which is in a 3430 */ -#define CONFIG_OMAP3_RX51 /* working with RX51 */ #define CONFIG_SYS_L2CACHE_OFF /* pretend there is no L2 CACHE */ #define CONFIG_MACH_TYPE MACH_TYPE_NOKIA_RX51 @@ -129,7 +125,6 @@ #define CONFIG_TWL4030_LED #define CONFIG_TWL4030_KEYPAD -#define CONFIG_OMAP_GPIO #define GPIO_SLIDE 71 /* diff --git a/include/configs/novena.h b/include/configs/novena.h index df0efbca92..e0ed304586 100644 --- a/include/configs/novena.h +++ b/include/configs/novena.h @@ -135,8 +135,6 @@ /* USB Configs */ #ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MX6 #define CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP #define CONFIG_USB_HOST_ETHER #define CONFIG_USB_ETHER_ASIX diff --git a/include/configs/nyan-big.h b/include/configs/nyan-big.h index d9d4f2d583..b5357ea15c 100644 --- a/include/configs/nyan-big.h +++ b/include/configs/nyan-big.h @@ -39,7 +39,6 @@ #define CONFIG_SPI_FLASH_SIZE (4 << 20) /* USB Host support */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_TEGRA /* USB networking support */ diff --git a/include/configs/o2dnt-common.h b/include/configs/o2dnt-common.h index e2881a7177..1b4200bcbf 100644 --- a/include/configs/o2dnt-common.h +++ b/include/configs/o2dnt-common.h @@ -68,7 +68,6 @@ /* * Supported commands */ -#define CONFIG_CMD_EEPROM #ifdef CONFIG_PCI #define CONFIG_CMD_PCI #endif @@ -173,27 +172,6 @@ #endif /* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 1 /* Select I2C module #1 or #2 */ -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration: - * - * O2DNT board is equiped with Ramtron FRAM device FM24CL16 - * 16 Kib Ferroelectric Nonvolatile serial RAM memory - * organized as 2048 x 8 bits and addressable as eight I2C devices - * 0x50 ... 0x57 each 256 bytes in size - * - */ -#define CONFIG_SYS_I2C_FRAM -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -/* * There is no write delay with FRAM, write operations are performed at bus * speed. Thus, no status polling or write delay is needed. */ diff --git a/include/configs/odroid.h b/include/configs/odroid.h index 6cc7dd16a2..afc7c5e35f 100644 --- a/include/configs/odroid.h +++ b/include/configs/odroid.h @@ -188,7 +188,6 @@ #define CONFIG_LIB_HW_RAND /* USB */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_EXYNOS #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 diff --git a/include/configs/odroid_xu3.h b/include/configs/odroid_xu3.h index 40b48f70ab..246fb808a9 100644 --- a/include/configs/odroid_xu3.h +++ b/include/configs/odroid_xu3.h @@ -41,7 +41,6 @@ #define CONFIG_DEFAULT_CONSOLE "console=ttySAC2,115200n8\0" /* USB */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_EXYNOS /* DFU */ diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h index c69b32531c..0d48d4ecc1 100644 --- a/include/configs/omap3_beagle.h +++ b/include/configs/omap3_beagle.h @@ -55,9 +55,7 @@ #define CONFIG_FASTBOOT_BUF_SIZE 0x07000000 /* USB EHCI */ -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_OMAP #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 147 #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 @@ -66,10 +64,6 @@ #define CONFIG_USB_ETHER_MCS7830 #define CONFIG_USB_ETHER_SMSC95XX -/* GPIO banks */ -#define CONFIG_OMAP3_GPIO_5 /* GPIO128..159 is in GPIO bank 5 */ -#define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO bank 6 */ - /* commands to include */ #define MTDIDS_DEFAULT "nand0=nand" diff --git a/include/configs/omap3_evm.h b/include/configs/omap3_evm.h index bf5b2f5139..d8ca6225d6 100644 --- a/include/configs/omap3_evm.h +++ b/include/configs/omap3_evm.h @@ -83,13 +83,9 @@ /* * High level configuration options */ -#define CONFIG_OMAP /* This is TI OMAP core */ -#define CONFIG_OMAP_GPIO #define CONFIG_SDRC /* The chip has SDRC controller */ -#define CONFIG_OMAP3_EVM /* This is a OMAP3 EVM */ - /* * Clock related definitions */ diff --git a/include/configs/omap3_igep00x0.h b/include/configs/omap3_igep00x0.h index 70d337e6f1..59da726bd6 100644 --- a/include/configs/omap3_igep00x0.h +++ b/include/configs/omap3_igep00x0.h @@ -37,11 +37,6 @@ #endif #endif -/* GPIO banks */ -#define CONFIG_OMAP3_GPIO_3 /* GPIO64 .. 95 is in GPIO bank 3 */ -#define CONFIG_OMAP3_GPIO_5 /* GPIO128..159 is in GPIO bank 5 */ -#define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO bank 6 */ - /* USB */ #define CONFIG_USB_MUSB_UDC 1 #define CONFIG_USB_OMAP3 1 diff --git a/include/configs/omap3_logic.h b/include/configs/omap3_logic.h index 772fc60c9c..f8978037f2 100644 --- a/include/configs/omap3_logic.h +++ b/include/configs/omap3_logic.h @@ -23,6 +23,7 @@ * DM support in SPL */ #undef CONFIG_DM_MMC +#undef CONFIG_DM_MMC_OPS #undef OMAP_HSMMC_USE_GPIO /* select serial console configuration for SPL */ @@ -49,10 +50,6 @@ /* Hardware drivers */ -/* GPIO banks */ -#define CONFIG_OMAP3_GPIO_4 /* GPIO 96..128 is in GPIO bank 4 */ -#define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO bank 6 */ - #define CONFIG_USB_OMAP3 /* commands to include */ diff --git a/include/configs/omap3_overo.h b/include/configs/omap3_overo.h index ebf7dd0c01..111aec58d3 100644 --- a/include/configs/omap3_overo.h +++ b/include/configs/omap3_overo.h @@ -40,18 +40,9 @@ #define CONFIG_TWL4030_LED /* USB EHCI */ -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_OMAP #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 183 #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 -/* Initialize GPIOs by default */ -#define CONFIG_OMAP3_GPIO_2 /* GPIO32..63 is in GPIO Bank 2 */ -#define CONFIG_OMAP3_GPIO_3 /* GPIO64..95 is in GPIO Bank 3 */ -#define CONFIG_OMAP3_GPIO_4 /* GPIO96..127 is in GPIO Bank 4 */ -#define CONFIG_OMAP3_GPIO_5 /* GPIO128..159 is in GPIO Bank 5 */ -#define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO Bank 6 */ - /* commands to include */ #ifdef CONFIG_NAND diff --git a/include/configs/omap3_pandora.h b/include/configs/omap3_pandora.h index ba7d3cdef5..efee5b0c3f 100644 --- a/include/configs/omap3_pandora.h +++ b/include/configs/omap3_pandora.h @@ -35,10 +35,6 @@ /* TWL4030 LED */ #define CONFIG_TWL4030_LED -/* Initialize GPIOs by default */ -#define CONFIG_OMAP3_GPIO_4 /* GPIO96..127 is in GPIO Bank 4 */ -#define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO Bank 6 */ - /* * NS16550 Configuration */ diff --git a/include/configs/omap3_zoom1.h b/include/configs/omap3_zoom1.h index aa27a9e68a..6c869c4c07 100644 --- a/include/configs/omap3_zoom1.h +++ b/include/configs/omap3_zoom1.h @@ -13,11 +13,6 @@ #ifndef __CONFIG_H #define __CONFIG_H -/* - * High Level Configuration Options - */ -#define CONFIG_OMAP3_ZOOM1 1 /* working with Zoom MDK Rev1 */ - #define CONFIG_NAND #define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */ #include <asm/arch/cpu.h> /* get chip and board defs */ diff --git a/include/configs/omap4_panda.h b/include/configs/omap4_panda.h index a6078daca6..e1263b68bc 100644 --- a/include/configs/omap4_panda.h +++ b/include/configs/omap4_panda.h @@ -17,8 +17,6 @@ */ /* USB UHH support options */ -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_OMAP #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 1 diff --git a/include/configs/omap5_uevm.h b/include/configs/omap5_uevm.h index 533bb02c5e..d8b0c023b9 100644 --- a/include/configs/omap5_uevm.h +++ b/include/configs/omap5_uevm.h @@ -52,8 +52,6 @@ #define CONFIG_SYS_I2C_TCA642X_ADDR 0x22 /* USB UHH support options */ -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_OMAP #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET @@ -68,9 +66,6 @@ #define CONSOLEDEV "ttyO2" -/* Max time to hold reset on this board, see doc/README.omap-reset-time */ -#define CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC 16296 - #define CONFIG_SCSI #define CONFIG_LIBATA #define CONFIG_SCSI_AHCI diff --git a/include/configs/ot1200.h b/include/configs/ot1200.h index b4d2b0a871..34da90f20b 100644 --- a/include/configs/ot1200.h +++ b/include/configs/ot1200.h @@ -55,8 +55,6 @@ #define CONFIG_SYS_FSL_USDHC_NUM 2 /* USB Configs */ -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MX6 #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 diff --git a/include/configs/p1_p2_rdb_pc.h b/include/configs/p1_p2_rdb_pc.h index d995d0448c..638e9da028 100644 --- a/include/configs/p1_p2_rdb_pc.h +++ b/include/configs/p1_p2_rdb_pc.h @@ -823,9 +823,7 @@ #define CONFIG_HAS_FSL_DR_USB #if defined(CONFIG_HAS_FSL_DR_USB) -#define CONFIG_USB_EHCI - -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_USB_EHCI_FSL #endif diff --git a/include/configs/p1_twr.h b/include/configs/p1_twr.h index dad0616517..427629f409 100644 --- a/include/configs/p1_twr.h +++ b/include/configs/p1_twr.h @@ -394,9 +394,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_HAS_FSL_DR_USB #if defined(CONFIG_HAS_FSL_DR_USB) -#define CONFIG_USB_EHCI - -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_USB_EHCI_FSL #endif diff --git a/include/configs/p2371-0000.h b/include/configs/p2371-0000.h index 897add3dd0..b106439071 100644 --- a/include/configs/p2371-0000.h +++ b/include/configs/p2371-0000.h @@ -33,7 +33,6 @@ #define CONFIG_SPI_FLASH_SIZE (4 << 20) /* USB2.0 Host support */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_TEGRA /* USB networking support */ diff --git a/include/configs/p2371-2180.h b/include/configs/p2371-2180.h index 3cf0c87be4..22fc122cc3 100644 --- a/include/configs/p2371-2180.h +++ b/include/configs/p2371-2180.h @@ -33,7 +33,6 @@ #define CONFIG_SPI_FLASH_SIZE (4 << 20) /* USB2.0 Host support */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_TEGRA /* USB networking support */ diff --git a/include/configs/p2571.h b/include/configs/p2571.h index 76fb7cec87..974fd3f59f 100644 --- a/include/configs/p2571.h +++ b/include/configs/p2571.h @@ -34,7 +34,6 @@ #define CONFIG_SPI_FLASH_SIZE (4 << 20) /* USB2.0 Host support */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_TEGRA /* USB networking support */ diff --git a/include/configs/paz00.h b/include/configs/paz00.h index 2e8cbd94cf..87a8557ea9 100644 --- a/include/configs/paz00.h +++ b/include/configs/paz00.h @@ -29,7 +29,6 @@ #define CONFIG_SYS_MMC_ENV_PART 2 /* USB Host support */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_TEGRA /* USB networking support */ diff --git a/include/configs/pcm030.h b/include/configs/pcm030.h index 6d8a2338a2..406f3e547a 100644 --- a/include/configs/pcm030.h +++ b/include/configs/pcm030.h @@ -49,7 +49,6 @@ Serial console configuration /* * Command line configuration. */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_JFFS2 #define CONFIG_CMD_PCI @@ -121,31 +120,6 @@ IPB Bus clocking configuration. #define CONFIG_SYS_XLB_PIPELINING 1 /*--------------------------------------------------------------------------- - I2C configuration ----------------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/*--------------------------------------------------------------------------- - EEPROM CAT24WC32 configuration ----------------------------------------------------------------------------*/ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 /* 1010100x */ -#define CONFIG_SYS_I2C_FACT_ADDR 0x52 /* EEPROM CAT24WC32 */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */ -#define CONFIG_SYS_EEPROM_SIZE 2048 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 15 - -/*--------------------------------------------------------------------------- -RTC configuration ----------------------------------------------------------------------------*/ -#define RTC -#define CONFIG_RTC_PCF8563 1 -#define CONFIG_SYS_I2C_RTC_ADDR 0x51 - -/*--------------------------------------------------------------------------- Flash configuration ---------------------------------------------------------------------------*/ @@ -172,11 +146,10 @@ RTC configuration Environment settings ---------------------------------------------------------------------------*/ -/* pcm030 ships with environment is EEPROM by default */ -#define CONFIG_ENV_IS_IN_EEPROM 1 +#define CONFIG_ENV_IS_NOWHERE #define CONFIG_ENV_OFFSET 0x00 /* environment starts at the */ /*beginning of the EEPROM */ -#define CONFIG_ENV_SIZE CONFIG_SYS_EEPROM_SIZE +#define CONFIG_ENV_SIZE 2048 #define CONFIG_ENV_OVERWRITE 1 diff --git a/include/configs/pdm360ng.h b/include/configs/pdm360ng.h index 501611dde7..4bd8236b33 100644 --- a/include/configs/pdm360ng.h +++ b/include/configs/pdm360ng.h @@ -302,34 +302,11 @@ #define CONFIG_SYS_PDM360NG_COPROC_BAUDRATE 38400 /* - * I2C - */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_I2C_CMD_TREE -/* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* * IIM - IC Identification Module */ #undef CONFIG_FSL_IIM /* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* 16-bit EEPROM addr */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* ST AT24C01 */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* 10ms of delay */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* 16-Byte Write Mode */ - -/* - * MAC addr in EEPROM - */ -#define CONFIG_SYS_I2C_EEPROM_BUS_NUM 0 -#define CONFIG_SYS_I2C_EEPROM_MAC_OFFSET 0x10 -/* * Enabled only to delete "ethaddr" before testing * "ethaddr" setting from EEPROM */ @@ -345,12 +322,6 @@ #define CONFIG_HAS_ETH0 /* - * Configure on-board RTC - */ -#define CONFIG_RTC_M41T62 /* use M41T00 rtc via i2c */ -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ - -/* * Environment */ #define CONFIG_ENV_IS_IN_FLASH 1 @@ -367,7 +338,6 @@ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_REGINFO #undef CONFIG_CMD_FUSE diff --git a/include/configs/pico-imx6ul.h b/include/configs/pico-imx6ul.h index 26b1b1147c..8d78f49c96 100644 --- a/include/configs/pico-imx6ul.h +++ b/include/configs/pico-imx6ul.h @@ -37,8 +37,6 @@ #define CONFIG_SUPPORT_EMMC_BOOT /* USB Configs */ -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MX6 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) #define CONFIG_MXC_USB_FLAGS 0 diff --git a/include/configs/picosam9g45.h b/include/configs/picosam9g45.h index 733768aa7b..998a7a344b 100644 --- a/include/configs/picosam9g45.h +++ b/include/configs/picosam9g45.h @@ -98,8 +98,6 @@ #define CONFIG_AT91_WANTS_COMMON_PHY /* USB */ -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_ATMEL #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 2 #define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */ diff --git a/include/configs/platinum.h b/include/configs/platinum.h index 6687c38c99..9c2182cbea 100644 --- a/include/configs/platinum.h +++ b/include/configs/platinum.h @@ -52,8 +52,6 @@ #define CONFIG_PHYLIB /* USB config */ -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MX6 #define CONFIG_MXC_USB_PORT 1 #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) #define CONFIG_MXC_USB_FLAGS 0 diff --git a/include/configs/plutux.h b/include/configs/plutux.h index 911cad8cdd..ff396eceb9 100644 --- a/include/configs/plutux.h +++ b/include/configs/plutux.h @@ -29,7 +29,6 @@ #define CONFIG_ENV_OFFSET (SZ_512M - SZ_128K) /* 128K sectors */ /* USB host support */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_TEGRA /* USB networking support */ diff --git a/include/configs/porter.h b/include/configs/porter.h index fabab73680..ac21411178 100644 --- a/include/configs/porter.h +++ b/include/configs/porter.h @@ -82,7 +82,6 @@ #define CONFIG_SYS_I2C_POWERIC_ADDR 0x58 /* da9063 */ /* USB */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_RMOBILE #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 diff --git a/include/configs/pxm2.h b/include/configs/pxm2.h index 57f034f0df..e8e0c7edd8 100644 --- a/include/configs/pxm2.h +++ b/include/configs/pxm2.h @@ -42,9 +42,6 @@ #define CONFIG_FACTORYSET -/* Watchdog */ -#define CONFIG_OMAP_WATCHDOG - #ifndef CONFIG_SPL_BUILD /* Use common default */ diff --git a/include/configs/r0p7734.h b/include/configs/r0p7734.h index 642572fc95..b159b1ed8d 100644 --- a/include/configs/r0p7734.h +++ b/include/configs/r0p7734.h @@ -40,20 +40,6 @@ # define CONFIG_SMC911X_BASE (0x84000000) #endif -/* I2C */ -#define CONFIG_SH_SH7734_I2C 1 -#define CONFIG_HARD_I2C 1 -#define CONFIG_I2C_MULTI_BUS 1 -#define CONFIG_SYS_MAX_I2C_BUS 2 -#define CONFIG_SYS_I2C_MODULE 0 -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x50 -#define CONFIG_SH_I2C_DATA_HIGH 4 -#define CONFIG_SH_I2C_DATA_LOW 5 -#define CONFIG_SH_I2C_CLOCK 500000000 -#define CONFIG_SH_I2C_BASE0 0xFFC70000 -#define CONFIG_SH_I2C_BASE1 0xFFC7100 - /* undef to save memory */ #define CONFIG_SYS_LONGHELP /* Monitor Command Prompt */ diff --git a/include/configs/rastaban.h b/include/configs/rastaban.h index 99fe1616e5..0820f6fc7a 100644 --- a/include/configs/rastaban.h +++ b/include/configs/rastaban.h @@ -49,9 +49,6 @@ #define CONFIG_FACTORYSET -/* Watchdog */ -#define CONFIG_OMAP_WATCHDOG - /* Define own nand partitions */ #define CONFIG_ENV_OFFSET_REDUND 0x2E0000 #define CONFIG_ENV_SIZE_REDUND 0x2000 diff --git a/include/configs/rut.h b/include/configs/rut.h index 8cfb73d781..e676a5acd4 100644 --- a/include/configs/rut.h +++ b/include/configs/rut.h @@ -110,10 +110,6 @@ #endif /* CONFIG_SPL_BUILD */ -#ifdef CONFIG_SPL_BUILD -#undef CONFIG_HW_WATCHDOG -#endif - #if defined(CONFIG_VIDEO) #define CONFIG_VIDEO_DA8XX #define CONFIG_SPLASH_SCREEN diff --git a/include/configs/s32v234evb.h b/include/configs/s32v234evb.h index 398b3aa343..33487cd86f 100644 --- a/include/configs/s32v234evb.h +++ b/include/configs/s32v234evb.h @@ -97,16 +97,6 @@ #define CONFIG_PHY_MICREL #endif -#if 0 /* Disable until the I2C driver will be updated */ - -/* I2C Configs */ -#define CONFIG_CMD_I2C -#define CONFIG_HARD_I2C -#define CONFIG_I2C_MXC -#define CONFIG_SYS_I2C_BASE I2C0_BASE_ADDR -#define CONFIG_SYS_I2C_SPEED 100000 -#endif - #if 0 /* Disable until the FLASH will be implemented */ #define CONFIG_SYS_USE_NAND #endif diff --git a/include/configs/sama5d2_ptc.h b/include/configs/sama5d2_ptc.h index 16bafc0990..7d20d65bf3 100644 --- a/include/configs/sama5d2_ptc.h +++ b/include/configs/sama5d2_ptc.h @@ -66,8 +66,6 @@ #define CONFIG_CMD_USB #ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_ATMEL #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 #endif diff --git a/include/configs/seaboard.h b/include/configs/seaboard.h index 207b59118d..afc2c7dfe9 100644 --- a/include/configs/seaboard.h +++ b/include/configs/seaboard.h @@ -37,7 +37,6 @@ #define CONFIG_SYS_MMC_ENV_PART 2 /* USB Host support */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_TEGRA /* USB networking support */ diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h index f5b03caf83..c39bb24420 100644 --- a/include/configs/sequoia.h +++ b/include/configs/sequoia.h @@ -192,16 +192,13 @@ /* USB */ #ifdef CONFIG_440EPX - -#undef CONFIG_USB_EHCI /* OHCI by default */ - -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD #define CONFIG_USB_EHCI_PPC4XX #define CONFIG_SYS_PPC4XX_USB_ADDR 0xe0000300 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_EHCI_MMIO_BIG_ENDIAN #define CONFIG_EHCI_DESC_BIG_ENDIAN -#else /* CONFIG_USB_EHCI */ +#else /* CONFIG_USB_EHCI_HCD */ #define CONFIG_USB_OHCI_NEW #define CONFIG_SYS_OHCI_BE_CONTROLLER diff --git a/include/configs/siemens-am33x-common.h b/include/configs/siemens-am33x-common.h index 508b849472..5bb471c8f6 100644 --- a/include/configs/siemens-am33x-common.h +++ b/include/configs/siemens-am33x-common.h @@ -15,7 +15,6 @@ #define __CONFIG_SIEMENS_AM33X_COMMON_H #define CONFIG_AM33XX -#define CONFIG_OMAP #include <asm/arch/omap.h> @@ -548,13 +547,6 @@ #endif #endif -#define CONFIG_OMAP_GPIO - -/* Gpio cmd support */ - -/* Watchdog */ -#define CONFIG_HW_WATCHDOG - /* Reboot after 60 sec if bootcmd fails */ #define CONFIG_RESET_TO_RETRY #define CONFIG_BOOT_RETRY_TIME 60 diff --git a/include/configs/silk.h b/include/configs/silk.h index 4fc270fcc2..84108fd523 100644 --- a/include/configs/silk.h +++ b/include/configs/silk.h @@ -82,7 +82,6 @@ #define CONFIG_SYS_I2C_POWERIC_ADDR 0x58 /* da9063 */ /* USB */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_RMOBILE #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 diff --git a/include/configs/snapper9g45.h b/include/configs/snapper9g45.h index 952c6f546f..99b5b23d29 100644 --- a/include/configs/snapper9g45.h +++ b/include/configs/snapper9g45.h @@ -61,8 +61,6 @@ #define CONFIG_TFTP_TSIZE /* USB */ -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_ATMEL #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 2 /* MMC */ diff --git a/include/configs/sniper.h b/include/configs/sniper.h index 5214827ad9..c56169dcff 100644 --- a/include/configs/sniper.h +++ b/include/configs/sniper.h @@ -19,12 +19,6 @@ #define CONFIG_ARM_ARCH_CP15_ERRATA /* - * Platform - */ - -#define CONFIG_OMAP - -/* * Board */ @@ -62,17 +56,6 @@ #define CONFIG_SYS_MALLOC_LEN (1024 * 1024 + CONFIG_ENV_SIZE) /* - * GPIO - */ - -#define CONFIG_OMAP_GPIO -#define CONFIG_OMAP3_GPIO_2 -#define CONFIG_OMAP3_GPIO_3 -#define CONFIG_OMAP3_GPIO_4 -#define CONFIG_OMAP3_GPIO_5 -#define CONFIG_OMAP3_GPIO_6 - -/* * I2C */ diff --git a/include/configs/stout.h b/include/configs/stout.h index 90258c2f42..16f3ce8647 100644 --- a/include/configs/stout.h +++ b/include/configs/stout.h @@ -84,7 +84,6 @@ #define CONFIG_SYS_TMU_CLK_DIV 4 /* USB */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_RMOBILE #define CONFIG_USB_MAX_CONTROLLER_COUNT 3 diff --git a/include/configs/sun4i.h b/include/configs/sun4i.h index 3dfd95ad77..bd349694c6 100644 --- a/include/configs/sun4i.h +++ b/include/configs/sun4i.h @@ -12,7 +12,7 @@ * A10 specific configuration */ -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD #define CONFIG_USB_EHCI_SUNXI #endif diff --git a/include/configs/sun50i.h b/include/configs/sun50i.h index 1b7bfb6c22..b7b67a1ddc 100644 --- a/include/configs/sun50i.h +++ b/include/configs/sun50i.h @@ -11,7 +11,7 @@ * A64 specific configuration */ -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD #define CONFIG_USB_EHCI_SUNXI #define CONFIG_USB_MAX_CONTROLLER_COUNT 1 #endif diff --git a/include/configs/sun5i.h b/include/configs/sun5i.h index ec8f3199ba..0535d6a7f3 100644 --- a/include/configs/sun5i.h +++ b/include/configs/sun5i.h @@ -12,7 +12,7 @@ * High Level Configuration Options */ -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD #define CONFIG_USB_EHCI_SUNXI #endif diff --git a/include/configs/sun6i.h b/include/configs/sun6i.h index 6c1eca4d26..8b9adb1be6 100644 --- a/include/configs/sun6i.h +++ b/include/configs/sun6i.h @@ -15,7 +15,7 @@ * A31 specific configuration */ -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD #define CONFIG_USB_EHCI_SUNXI #endif diff --git a/include/configs/sun7i.h b/include/configs/sun7i.h index 5455901efe..12c96230c2 100644 --- a/include/configs/sun7i.h +++ b/include/configs/sun7i.h @@ -13,7 +13,7 @@ * A20 specific configuration */ -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD #define CONFIG_USB_EHCI_SUNXI #endif diff --git a/include/configs/sun8i.h b/include/configs/sun8i.h index 6ac42acaea..47f2813240 100644 --- a/include/configs/sun8i.h +++ b/include/configs/sun8i.h @@ -13,7 +13,7 @@ * A23 specific configuration */ -#ifdef CONFIG_USB_EHCI +#ifdef CONFIG_USB_EHCI_HCD #define CONFIG_USB_EHCI_SUNXI #endif diff --git a/include/configs/tam3517-common.h b/include/configs/tam3517-common.h index 0bdf52eb68..34ce122489 100644 --- a/include/configs/tam3517-common.h +++ b/include/configs/tam3517-common.h @@ -13,8 +13,6 @@ /* * High Level Configuration Options */ -#define CONFIG_OMAP /* in a TI OMAP core */ -#define CONFIG_OMAP_GPIO #define CONFIG_SYS_TEXT_BASE 0x80008000 @@ -43,7 +41,6 @@ /* * DDR related */ -#define CONFIG_OMAP3_MICRON_DDR /* Micron DDR */ #define CONFIG_SYS_CS0_SIZE (256 * 1024 * 1024) /* @@ -69,9 +66,6 @@ #define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\ 115200} /* EHCI */ -#define CONFIG_OMAP3_GPIO_5 -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_OMAP #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 25 #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 diff --git a/include/configs/tao3530.h b/include/configs/tao3530.h index 9bb4a1a8c0..ae6c768c22 100644 --- a/include/configs/tao3530.h +++ b/include/configs/tao3530.h @@ -16,9 +16,6 @@ /* * High Level Configuration Options */ -#define CONFIG_OMAP /* in a TI OMAP core */ - -#define CONFIG_OMAP_GPIO #define CONFIG_SDRC /* Has an SDRC controller */ @@ -64,13 +61,6 @@ /* allow to overwrite serial and ethaddr */ #define CONFIG_ENV_OVERWRITE -/* GPIO banks */ -#define CONFIG_OMAP3_GPIO_2 /* GPIO32 ..63 is in GPIO bank 2 */ -#define CONFIG_OMAP3_GPIO_3 /* GPIO64 ..95 is in GPIO bank 3 */ -#define CONFIG_OMAP3_GPIO_4 /* GPIO96 ..127 is in GPIO bank 4 */ -#define CONFIG_OMAP3_GPIO_5 /* GPIO128..159 is in GPIO bank 5 */ -#define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO bank 6 */ - /* commands to include */ #define CONFIG_CMD_MTDPARTS /* Enable MTD parts commands */ #define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ @@ -238,8 +228,6 @@ */ /* USB EHCI */ -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_OMAP #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 162 #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 diff --git a/include/configs/tbs2910.h b/include/configs/tbs2910.h index b4a14eae7c..9720a09b32 100644 --- a/include/configs/tbs2910.h +++ b/include/configs/tbs2910.h @@ -93,8 +93,6 @@ /* USB */ #ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MX6 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) diff --git a/include/configs/tec-ng.h b/include/configs/tec-ng.h index 06d8720df2..6406d39698 100644 --- a/include/configs/tec-ng.h +++ b/include/configs/tec-ng.h @@ -33,7 +33,6 @@ #define CONFIG_SPI_FLASH_SIZE (4 << 20) /* USB Host support */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_TEGRA /* USB networking support */ diff --git a/include/configs/tec.h b/include/configs/tec.h index b380a69bdf..8ffdbec9d1 100644 --- a/include/configs/tec.h +++ b/include/configs/tec.h @@ -29,7 +29,6 @@ #define CONFIG_ENV_OFFSET (SZ_512M - SZ_128K) /* 128K sectors */ /* USB host support */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_TEGRA /* USB networking support */ diff --git a/include/configs/tegra-common-post.h b/include/configs/tegra-common-post.h index ab4136ab13..1a4a7e2320 100644 --- a/include/configs/tegra-common-post.h +++ b/include/configs/tegra-common-post.h @@ -123,9 +123,6 @@ #endif /* remove USB */ -#ifdef CONFIG_USB_EHCI -#undef CONFIG_USB_EHCI -#endif #ifdef CONFIG_USB_EHCI_TEGRA #undef CONFIG_USB_EHCI_TEGRA #endif diff --git a/include/configs/thuban.h b/include/configs/thuban.h index 8c37d7cace..cea84acd03 100644 --- a/include/configs/thuban.h +++ b/include/configs/thuban.h @@ -42,9 +42,6 @@ #define CONFIG_FACTORYSET -/* Watchdog */ -#define CONFIG_OMAP_WATCHDOG - /* Define own nand partitions */ #define CONFIG_ENV_OFFSET_REDUND 0x2E0000 #define CONFIG_ENV_SIZE_REDUND 0x2000 diff --git a/include/configs/ti814x_evm.h b/include/configs/ti814x_evm.h index baf818ba1a..60322b1938 100644 --- a/include/configs/ti814x_evm.h +++ b/include/configs/ti814x_evm.h @@ -18,7 +18,6 @@ #define CONFIG_TI81XX #define CONFIG_TI814X -#define CONFIG_OMAP #include <asm/arch/omap.h> @@ -110,8 +109,6 @@ #define CONFIG_SYS_LOAD_ADDR 0x81000000 /* Default */ -#define CONFIG_OMAP_GPIO - /** * Physical Memory Map */ diff --git a/include/configs/ti816x_evm.h b/include/configs/ti816x_evm.h index b7ec200e06..51b09d4b56 100644 --- a/include/configs/ti816x_evm.h +++ b/include/configs/ti816x_evm.h @@ -12,7 +12,6 @@ #define CONFIG_TI81XX #define CONFIG_TI816X -#define CONFIG_OMAP #define CONFIG_ARCH_CPU_INIT @@ -50,7 +49,6 @@ #define CONFIG_SYS_LOAD_ADDR 0x81000000 /* Default load address */ #define CONFIG_CMD_ASKENV -#define CONFIG_OMAP_GPIO #define CONFIG_FS_FAT diff --git a/include/configs/ti_am335x_common.h b/include/configs/ti_am335x_common.h index e4c3c807f2..bf44121a0f 100644 --- a/include/configs/ti_am335x_common.h +++ b/include/configs/ti_am335x_common.h @@ -47,10 +47,6 @@ */ #define CONFIG_SYS_BOOTCOUNT_ADDR 0x44E3E000 -/* Enable the HW watchdog, since we can use this with bootcount */ -#define CONFIG_HW_WATCHDOG -#define CONFIG_OMAP_WATCHDOG - /* * SPL related defines. The Public RAM memory map the ROM defines the * area between 0x402F0400 and 0x4030B800 as a download area and diff --git a/include/configs/ti_armv7_omap.h b/include/configs/ti_armv7_omap.h index de14b8575a..b4565daf41 100644 --- a/include/configs/ti_armv7_omap.h +++ b/include/configs/ti_armv7_omap.h @@ -12,9 +12,6 @@ #ifndef __CONFIG_TI_ARMV7_OMAP_H__ #define __CONFIG_TI_ARMV7_OMAP_H__ -/* Common defines for all OMAP architecture based SoCs */ -#define CONFIG_OMAP - /* I2C IP block */ #define CONFIG_SYS_OMAP24_I2C_SPEED 100000 #define CONFIG_SYS_OMAP24_I2C_SLAVE 1 @@ -23,9 +20,6 @@ /* SPI IP Block */ #define CONFIG_OMAP3_SPI -/* GPIO block */ -#define CONFIG_OMAP_GPIO - /* * GPMC NAND block. We support 1 device and the physical address to * access CS0 at is 0x8000000. diff --git a/include/configs/ti_omap4_common.h b/include/configs/ti_omap4_common.h index b85db500b5..1a6551e24d 100644 --- a/include/configs/ti_omap4_common.h +++ b/include/configs/ti_omap4_common.h @@ -12,10 +12,6 @@ #ifndef __CONFIG_TI_OMAP4_COMMON_H #define __CONFIG_TI_OMAP4_COMMON_H -/* - * High Level Configuration Options - */ -#define CONFIG_OMAP4430 1 /* which is in a 4430 */ #define CONFIG_MISC_INIT_R #ifndef CONFIG_SYS_L2CACHE_OFF diff --git a/include/configs/titanium.h b/include/configs/titanium.h index 2c05f9c930..79e37e2cef 100644 --- a/include/configs/titanium.h +++ b/include/configs/titanium.h @@ -50,8 +50,6 @@ #define CONFIG_PHY_MICREL_KSZ9021 /* USB Configs */ -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MX6 #define CONFIG_MXC_USB_PORT 1 #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) #define CONFIG_MXC_USB_FLAGS 0 diff --git a/include/configs/tqma6.h b/include/configs/tqma6.h index e662e65204..738693c0c0 100644 --- a/include/configs/tqma6.h +++ b/include/configs/tqma6.h @@ -81,8 +81,6 @@ #define CONFIG_SYS_FSL_ESDHC_ADDR 0 /* USB Configs */ -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MX6 #define CONFIG_USB_HOST_ETHER #define CONFIG_USB_ETHER_SMSC95XX #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) diff --git a/include/configs/tricorder.h b/include/configs/tricorder.h index 9741ca5fc9..8fe4165a77 100644 --- a/include/configs/tricorder.h +++ b/include/configs/tricorder.h @@ -16,9 +16,6 @@ #ifndef __CONFIG_H #define __CONFIG_H -/* High Level Configuration Options */ -#define CONFIG_OMAP /* in a TI OMAP core */ - #define CONFIG_MACH_TYPE MACH_TYPE_TRICORDER /* * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM @@ -49,14 +46,6 @@ /* Hardware drivers */ -/* GPIO support */ -#define CONFIG_OMAP_GPIO - -/* GPIO banks */ -#define CONFIG_OMAP3_GPIO_2 /* GPIO32..63 are in GPIO bank 2 */ - -/* LED support */ - /* NS16550 Configuration */ #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE (-4) diff --git a/include/configs/trimslice.h b/include/configs/trimslice.h index 2c37107a3c..ab9c5c3ab8 100644 --- a/include/configs/trimslice.h +++ b/include/configs/trimslice.h @@ -36,7 +36,6 @@ #define CONFIG_ENV_OFFSET (SZ_1M - CONFIG_ENV_SIZE) /* USB Host support */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_TEGRA /* USB networking support */ diff --git a/include/configs/twister.h b/include/configs/twister.h index 30ad241f7f..a7de75ec6f 100644 --- a/include/configs/twister.h +++ b/include/configs/twister.h @@ -45,7 +45,4 @@ #define CONFIG_SYS_SPL_ARGS_ADDR (PHYS_SDRAM_1 + 0x100) #define CONFIG_SPL_BOARD_INIT -/* gpio 55 is used as SPL_OS_BOOT_KEY */ -#define CONFIG_OMAP3_GPIO_2 - #endif /* __CONFIG_H */ diff --git a/include/configs/usbarmory.h b/include/configs/usbarmory.h index 58b62d2448..f725b79cd4 100644 --- a/include/configs/usbarmory.h +++ b/include/configs/usbarmory.h @@ -41,7 +41,6 @@ #define CONFIG_SYS_FSL_ESDHC_NUM 1 /* USB */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_MX5 #define CONFIG_MXC_USB_PORT 1 #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) diff --git a/include/configs/v38b.h b/include/configs/v38b.h index cc0007827d..0bc0ae517a 100644 --- a/include/configs/v38b.h +++ b/include/configs/v38b.h @@ -135,27 +135,6 @@ #undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ /* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70 - -/* - * RTC configuration - */ -#define CONFIG_SYS_I2C_RTC_ADDR 0x51 - -/* * Flash configuration - use CFI driver */ #define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ diff --git a/include/configs/vct.h b/include/configs/vct.h index 9db6fee6e7..b1dccdf666 100644 --- a/include/configs/vct.h +++ b/include/configs/vct.h @@ -99,7 +99,6 @@ /* * USB/EHCI */ -#define CONFIG_USB_EHCI /* Enable EHCI USB support */ #define CONFIG_USB_EHCI_VCT /* on VCT platform */ #define CONFIG_EHCI_MMIO_BIG_ENDIAN #define CONFIG_EHCI_DESC_BIG_ENDIAN diff --git a/include/configs/venice2.h b/include/configs/venice2.h index 9e83863c0a..850a9bd49a 100644 --- a/include/configs/venice2.h +++ b/include/configs/venice2.h @@ -34,7 +34,6 @@ #define CONFIG_SPI_FLASH_SIZE (4 << 20) /* USB Host support */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_TEGRA /* USB networking support */ diff --git a/include/configs/ventana.h b/include/configs/ventana.h index 0e851a1b10..1ab6476f3c 100644 --- a/include/configs/ventana.h +++ b/include/configs/ventana.h @@ -27,7 +27,6 @@ #define CONFIG_SYS_MMC_ENV_PART 2 /* USB Host support */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_TEGRA /* USB networking support */ diff --git a/include/configs/vinco.h b/include/configs/vinco.h index c146f773db..dc35b289d4 100644 --- a/include/configs/vinco.h +++ b/include/configs/vinco.h @@ -66,8 +66,6 @@ /* USB */ #ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_ATMEL #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 #endif diff --git a/include/configs/vining_2000.h b/include/configs/vining_2000.h index 9a517a9738..78e14b38c1 100644 --- a/include/configs/vining_2000.h +++ b/include/configs/vining_2000.h @@ -76,8 +76,6 @@ #define CONFIG_PHY_ATHEROS #ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MX6 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_USB_HOST_ETHER #define CONFIG_USB_ETHER_ASIX diff --git a/include/configs/wandboard.h b/include/configs/wandboard.h index 47daf724ab..3e0ea71e69 100644 --- a/include/configs/wandboard.h +++ b/include/configs/wandboard.h @@ -50,8 +50,6 @@ #define CONFIG_SYS_FSL_ESDHC_ADDR 0 /* USB Configs */ -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MX6 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) #define CONFIG_MXC_USB_FLAGS 0 diff --git a/include/configs/warp.h b/include/configs/warp.h index 5274b274a4..afe3eaed46 100644 --- a/include/configs/warp.h +++ b/include/configs/warp.h @@ -58,8 +58,6 @@ /* USB Configs */ #ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MX6 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) #define CONFIG_MXC_USB_FLAGS 0 diff --git a/include/configs/whistler.h b/include/configs/whistler.h index 429e5b6a32..9f350d556a 100644 --- a/include/configs/whistler.h +++ b/include/configs/whistler.h @@ -36,7 +36,6 @@ #define CONFIG_SYS_MMC_ENV_PART 2 /* USB Host support */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_TEGRA /* USB networking support */ diff --git a/include/configs/x600.h b/include/configs/x600.h index 6e52e56222..bf6fafce98 100644 --- a/include/configs/x600.h +++ b/include/configs/x600.h @@ -100,7 +100,6 @@ #define CONFIG_FPGA_COUNT 1 /* USB EHCI options */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_SPEAR #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 diff --git a/include/configs/x86-common.h b/include/configs/x86-common.h index 653a30d3bd..29be55a840 100644 --- a/include/configs/x86-common.h +++ b/include/configs/x86-common.h @@ -134,7 +134,6 @@ /*----------------------------------------------------------------------- * USB configuration */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_PCI #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 12 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 diff --git a/include/configs/xpedite550x.h b/include/configs/xpedite550x.h index 2793a9bfb9..ad4247ab48 100644 --- a/include/configs/xpedite550x.h +++ b/include/configs/xpedite550x.h @@ -332,7 +332,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); /* * USB */ -#define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_FSL #define CONFIG_EHCI_HCD_INIT_AFTER_RESET diff --git a/include/configs/xpress.h b/include/configs/xpress.h index e3ae4e8f74..e13b792f38 100644 --- a/include/configs/xpress.h +++ b/include/configs/xpress.h @@ -64,8 +64,6 @@ #define CONFIG_MMCROOT "/dev/mmcblk0p2" /* USDHC2 */ /* USB Configs */ -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MX6 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) #define CONFIG_MXC_USB_FLAGS 0 diff --git a/include/configs/zmx25.h b/include/configs/zmx25.h index c61c353901..c1daf65621 100644 --- a/include/configs/zmx25.h +++ b/include/configs/zmx25.h @@ -82,7 +82,6 @@ * USB */ #ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI /* Enable EHCI USB support */ #define CONFIG_USB_EHCI_MXC #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_MXC_USB_PORT 1 diff --git a/include/edid.h b/include/edid.h index 8b022fa98a..a9f2f3d3ab 100644 --- a/include/edid.h +++ b/include/edid.h @@ -19,6 +19,9 @@ #define EDID_SIZE 128 #define EDID_EXT_SIZE 256 +/* OUI of HDMI vendor specific data block */ +#define HDMI_IEEE_OUI 0x000c03 + #define GET_BIT(_x, _pos) \ (((_x) >> (_pos)) & 1) #define GET_BITS(_x, _pos_msb, _pos_lsb) \ @@ -234,6 +237,13 @@ struct edid1_info { unsigned char checksum; } __attribute__ ((__packed__)); +enum edid_cea861_db_types { + EDID_CEA861_DB_AUDIO = 0x01, + EDID_CEA861_DB_VIDEO = 0x02, + EDID_CEA861_DB_VENDOR = 0x03, + EDID_CEA861_DB_SPEAKER = 0x04, +}; + struct edid_cea861_info { unsigned char extension_tag; #define EDID_CEA861_EXTENSION_TAG 0x02 @@ -251,6 +261,10 @@ struct edid_cea861_info { #define EDID_CEA861_DTD_COUNT(_x) \ GET_BITS(((_x).dtd_count), 3, 0) unsigned char data[124]; +#define EDID_CEA861_DB_TYPE(_x, offset) \ + GET_BITS((_x).data[offset], 7, 5) +#define EDID_CEA861_DB_LEN(_x, offset) \ + GET_BITS((_x).data[offset], 4, 0) } __attribute__ ((__packed__)); /** diff --git a/include/fdtdec.h b/include/fdtdec.h index b0e5b2767d..3000ecbb58 100644 --- a/include/fdtdec.h +++ b/include/fdtdec.h @@ -967,6 +967,7 @@ struct display_timing { struct timing_entry vsync_len; /* ver. sync len */ enum display_flags flags; /* display flags */ + bool hdmi_monitor; /* is hdmi monitor? */ }; /** diff --git a/include/i2c.h b/include/i2c.h index cd7f61e1c1..a88cc7cddf 100644 --- a/include/i2c.h +++ b/include/i2c.h @@ -706,9 +706,6 @@ void i2c_early_init_f(void); #endif void i2c_init(int speed, int slaveaddr); void i2c_init_board(void); -#ifdef CONFIG_SYS_I2C_BOARD_LATE_INIT -void i2c_board_late_init(void); -#endif #ifdef CONFIG_SYS_I2C /* diff --git a/include/spl.h b/include/spl.h index d1638e9d7c..ffadce93c7 100644 --- a/include/spl.h +++ b/include/spl.h @@ -267,4 +267,5 @@ int spl_dfu_cmd(int usbctrl, char *dfu_alt_info, char *interface, char *devstr); int spl_mmc_load_image(struct spl_image_info *spl_image, struct spl_boot_device *bootdev); +void bl31_entry(void); #endif diff --git a/include/usb.h b/include/usb.h index 02a0ccdd77..62f051fe53 100644 --- a/include/usb.h +++ b/include/usb.h @@ -187,7 +187,8 @@ int submit_control_msg(struct usb_device *dev, unsigned long pipe, void *buffer, int submit_int_msg(struct usb_device *dev, unsigned long pipe, void *buffer, int transfer_len, int interval); -#if defined CONFIG_USB_EHCI || defined CONFIG_USB_MUSB_HOST || defined(CONFIG_DM_USB) +#if defined CONFIG_USB_EHCI_HCD || defined CONFIG_USB_MUSB_HOST \ + || defined(CONFIG_DM_USB) struct int_queue *create_int_queue(struct usb_device *dev, unsigned long pipe, int queuesize, int elementsize, void *buffer, int interval); int destroy_int_queue(struct usb_device *dev, struct int_queue *queue); diff --git a/scripts/Makefile.extrawarn b/scripts/Makefile.extrawarn index 7b2cffce52..90dc149df3 100644 --- a/scripts/Makefile.extrawarn +++ b/scripts/Makefile.extrawarn @@ -58,9 +58,23 @@ endif KBUILD_CFLAGS += $(warning) +dtc-warning-2 += $(call dtc-option,-Wnode_name_chars_strict) +dtc-warning-2 += $(call dtc-option,-Wproperty_name_chars_strict) + +dtc-warning := $(dtc-warning-$(findstring 1, $(KBUILD_ENABLE_EXTRA_GCC_CHECKS))) +dtc-warning += $(dtc-warning-$(findstring 2, $(KBUILD_ENABLE_EXTRA_GCC_CHECKS))) +dtc-warning += $(dtc-warning-$(findstring 3, $(KBUILD_ENABLE_EXTRA_GCC_CHECKS))) + +DTC_FLAGS += $(dtc-warning) + else # Disable noisy checks by default DTC_FLAGS += $(call dtc-option,-Wno-unit_address_vs_reg) +DTC_FLAGS += $(call dtc-option,-Wno-simple_bus_reg) +DTC_FLAGS += $(call dtc-option,-Wno-unit_address_format) +DTC_FLAGS += $(call dtc-option,-Wno-pci_bridge) +DTC_FLAGS += $(call dtc-option,-Wno-pci_device_bus_num) +DTC_FLAGS += $(call dtc-option,-Wno-pci_device_reg) endif diff --git a/scripts/config_whitelist.txt b/scripts/config_whitelist.txt index 7646bb6842..fa9c3fc8cb 100644 --- a/scripts/config_whitelist.txt +++ b/scripts/config_whitelist.txt @@ -236,7 +236,6 @@ CONFIG_BL1_SIZE CONFIG_BL2_OFFSET CONFIG_BL2_SIZE CONFIG_BMP_16BPP -CONFIG_BMP_24BMP CONFIG_BMP_24BPP CONFIG_BMP_32BPP CONFIG_BOARDDIR @@ -617,7 +616,6 @@ CONFIG_DEEP_SLEEP CONFIG_DEFAULT CONFIG_DEFAULT_CONSOLE CONFIG_DEFAULT_IMMR -CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC CONFIG_DEFAULT_SPI_BUS CONFIG_DEFAULT_SPI_CS CONFIG_DEFAULT_SPI_MODE @@ -1134,7 +1132,6 @@ CONFIG_G_DNL_UMS_VENDOR_NUM CONFIG_H264_FREQ CONFIG_H8300 CONFIG_HALEAKALA -CONFIG_HARD_I2C CONFIG_HARD_SPI CONFIG_HASH_VERIFY CONFIG_HAS_DATAFLASH @@ -1320,7 +1317,6 @@ CONFIG_HW_ENV_SETTINGS CONFIG_HW_WATCHDOG CONFIG_HW_WATCHDOG_TIMEOUT_MS CONFIG_I2C -CONFIG_I2CFAST CONFIG_I2C_CHIPADDRESS CONFIG_I2C_CMD_TREE CONFIG_I2C_ENV_EEPROM_BUS @@ -1980,33 +1976,12 @@ CONFIG_OF_SPI CONFIG_OF_SPI_FLASH CONFIG_OF_STDOUT_PATH CONFIG_OF_SUPPORT_OLD_DEVICE_TREES -CONFIG_OMAP -CONFIG_OMAP3430 -CONFIG_OMAP3_AM3517CRANE -CONFIG_OMAP3_DEVKIT8000 -CONFIG_OMAP3_EVM -CONFIG_OMAP3_GPIO_2 -CONFIG_OMAP3_GPIO_3 -CONFIG_OMAP3_GPIO_4 -CONFIG_OMAP3_GPIO_5 -CONFIG_OMAP3_GPIO_6 -CONFIG_OMAP3_LOGIC_USE_NEW_PRODUCT_ID -CONFIG_OMAP3_MCX -CONFIG_OMAP3_MICRON_DDR -CONFIG_OMAP3_RX51 -CONFIG_OMAP3_SPI_D0_D1_SWAPPED -CONFIG_OMAP3_ZOOM1 -CONFIG_OMAP4430 CONFIG_OMAP_EHCI_PHY1_RESET_GPIO CONFIG_OMAP_EHCI_PHY2_RESET_GPIO CONFIG_OMAP_EHCI_PHY3_RESET_GPIO -CONFIG_OMAP_GPIO -CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC CONFIG_OMAP_USB2PHY2_HOST CONFIG_OMAP_USB3PHY1_HOST CONFIG_OMAP_USB_PHY -CONFIG_OMAP_VC_I2C_HS_MCODE -CONFIG_OMAP_WATCHDOG CONFIG_OPTREX_BW CONFIG_ORIGEN CONFIG_OS1_ENV_ADDR @@ -4223,7 +4198,6 @@ CONFIG_SYS_I2C_BASE2 CONFIG_SYS_I2C_BASE3 CONFIG_SYS_I2C_BASE4 CONFIG_SYS_I2C_BASE5 -CONFIG_SYS_I2C_BOARD_LATE_INIT CONFIG_SYS_I2C_BOOT_EEPROM_ADDR CONFIG_SYS_I2C_BUSES CONFIG_SYS_I2C_BUS_MAX @@ -6307,7 +6281,6 @@ CONFIG_USB_EHCI_KIRKWOOD CONFIG_USB_EHCI_MX5 CONFIG_USB_EHCI_MXC CONFIG_USB_EHCI_MXS -CONFIG_USB_EHCI_OMAP CONFIG_USB_EHCI_PCI CONFIG_USB_EHCI_PPC4XX CONFIG_USB_EHCI_RMOBILE |