diff options
| -rw-r--r-- | arch/arm/cpu/armv7/mx5/lowlevel_init.S | 95 |
1 files changed, 65 insertions, 30 deletions
diff --git a/arch/arm/cpu/armv7/mx5/lowlevel_init.S b/arch/arm/cpu/armv7/mx5/lowlevel_init.S index 529e35b440..d0bab4545a 100644 --- a/arch/arm/cpu/armv7/mx5/lowlevel_init.S +++ b/arch/arm/cpu/armv7/mx5/lowlevel_init.S @@ -162,9 +162,9 @@ setup_pll_func: .endm .macro init_clock +#if defined (CONFIG_MX51) ldr r0, =CCM_BASE_ADDR -#if defined(CONFIG_MX51) /* Gate of clocks to the peripherals first */ ldr r1, =0x3FFFFFFF str r1, [r0, #CLKCTL_CCGR0] @@ -190,21 +190,6 @@ setup_pll_func: 1: ldr r1, [r0, #CLKCTL_CDHIPR] cmp r1, #0x0 bne 1b -#else - ldr r1, =0x3FFFFFFF - str r1, [r0, #CLKCTL_CCGR0] - str r4, [r0, #CLKCTL_CCGR1] - str r4, [r0, #CLKCTL_CCGR2] - str r4, [r0, #CLKCTL_CCGR3] - str r4, [r0, #CLKCTL_CCGR7] - - ldr r1, =0x00030000 - str r1, [r0, #CLKCTL_CCGR4] - ldr r1, =0x00FFF030 - str r1, [r0, #CLKCTL_CCGR5] - ldr r1, =0x0F00030F - str r1, [r0, #CLKCTL_CCGR6] -#endif /* Switch ARM to step clock */ mov r1, #0x4 @@ -217,7 +202,6 @@ setup_pll_func: setup_pll PLL1_BASE_ADDR, 800 #endif -#if defined(CONFIG_MX51) setup_pll PLL3_BASE_ADDR, 665 /* Switch peripheral to PLL 3 */ @@ -234,7 +218,7 @@ setup_pll_func: str r1, [r0, #CLKCTL_CBCDR] ldr r1, =0x000020C0 | CONFIG_SYS_DDR_CLKSEL str r1, [r0, #CLKCTL_CBCMR] -#endif + setup_pll PLL3_BASE_ADDR, 216 /* Set the platform clock dividers */ @@ -244,21 +228,17 @@ setup_pll_func: ldr r0, =CCM_BASE_ADDR -#if defined(CONFIG_MX51) /* Run 3.0 at Full speed, for other TO's wait till we increase VDDGP */ ldr r3, [r4, #ROM_SI_REV] cmp r3, #0x10 movls r1, #0x1 movhi r1, #0 -#else - mov r1, #0 -#endif + str r1, [r0, #CLKCTL_CACRR] /* Switch ARM back to PLL 1 */ str r4, [r0, #CLKCTL_CCSR] -#if defined(CONFIG_MX51) /* setup the rest */ /* Use lp_apm (24MHz) source for perclk */ ldr r1, =0x000020C2 | CONFIG_SYS_DDR_CLKSEL @@ -266,7 +246,6 @@ setup_pll_func: /* ddr clock from PLL 1, all perclk dividers are 1 since using 24MHz */ ldr r1, =CONFIG_SYS_CLKTL_CBCDR str r1, [r0, #CLKCTL_CBCDR] -#endif /* Restore the default values in the Gate registers */ ldr r1, =0xFFFFFFFF @@ -277,17 +256,72 @@ setup_pll_func: str r1, [r0, #CLKCTL_CCGR4] str r1, [r0, #CLKCTL_CCGR5] str r1, [r0, #CLKCTL_CCGR6] -#if defined(CONFIG_MX53) - str r1, [r0, #CLKCTL_CCGR7] -#endif -#if defined(CONFIG_MX51) /* Use PLL 2 for UART's, get 66.5MHz from it */ ldr r1, =0xA5A2A020 str r1, [r0, #CLKCTL_CSCMR1] ldr r1, =0x00C30321 str r1, [r0, #CLKCTL_CSCDR1] -#elif defined(CONFIG_MX53) + /* make sure divider effective */ +1: ldr r1, [r0, #CLKCTL_CDHIPR] + cmp r1, #0x0 + bne 1b + + str r4, [r0, #CLKCTL_CCDR] + + /* for cko - for ARM div by 8 */ + mov r1, #0x000A0000 + add r1, r1, #0x00000F0 + str r1, [r0, #CLKCTL_CCOSR] +#else /* CONFIG_MX53 */ + ldr r0, =CCM_BASE_ADDR + + /* Gate of clocks to the peripherals first */ + ldr r1, =0x3FFFFFFF + str r1, [r0, #CLKCTL_CCGR0] + str r4, [r0, #CLKCTL_CCGR1] + str r4, [r0, #CLKCTL_CCGR2] + str r4, [r0, #CLKCTL_CCGR3] + str r4, [r0, #CLKCTL_CCGR7] + ldr r1, =0x00030000 + str r1, [r0, #CLKCTL_CCGR4] + ldr r1, =0x00FFF030 + str r1, [r0, #CLKCTL_CCGR5] + ldr r1, =0x0F00030F + str r1, [r0, #CLKCTL_CCGR6] + + /* Switch ARM to step clock */ + mov r1, #0x4 + str r1, [r0, #CLKCTL_CCSR] + + setup_pll PLL1_BASE_ADDR, 800 + + setup_pll PLL3_BASE_ADDR, 216 + + /* Set the platform clock dividers */ + ldr r0, =ARM_BASE_ADDR + ldr r1, =0x00000725 + str r1, [r0, #0x14] + + ldr r0, =CCM_BASE_ADDR + + mov r1, #0 + str r1, [r0, #CLKCTL_CACRR] + + /* Switch ARM back to PLL 1 */ + str r4, [r0, #CLKCTL_CCSR] + + /* Restore the default values in the Gate registers */ + ldr r1, =0xFFFFFFFF + str r1, [r0, #CLKCTL_CCGR0] + str r1, [r0, #CLKCTL_CCGR1] + str r1, [r0, #CLKCTL_CCGR2] + str r1, [r0, #CLKCTL_CCGR3] + str r1, [r0, #CLKCTL_CCGR4] + str r1, [r0, #CLKCTL_CCGR5] + str r1, [r0, #CLKCTL_CCGR6] + str r1, [r0, #CLKCTL_CCGR7] + /* Switch peripheral to PLL2 */ ldr r0, =CCM_BASE_ADDR ldr r1, =0x00808145 @@ -306,7 +340,7 @@ setup_pll_func: and r1, r1, #0xffffffc0 orr r1, r1, #0x0a str r1, [r0, #CLKCTL_CSCDR1] -#endif + /* make sure divider effective */ 1: ldr r1, [r0, #CLKCTL_CDHIPR] cmp r1, #0x0 @@ -318,6 +352,7 @@ setup_pll_func: mov r1, #0x000A0000 add r1, r1, #0x00000F0 str r1, [r0, #CLKCTL_CCOSR] +#endif /* CONFIG_MX53 */ .endm .macro setup_wdog |