summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
Diffstat
-rw-r--r--MAINTAINERS4
-rwxr-xr-xMAKEALL1
-rw-r--r--Makefile2
-rw-r--r--board/mpc8641hpcn/mpc8641hpcn.c4
-rw-r--r--board/sbc8641d/Makefile52
-rw-r--r--board/sbc8641d/config.mk30
-rw-r--r--board/sbc8641d/init.S192
-rw-r--r--board/sbc8641d/sbc8641d.c406
-rw-r--r--board/sbc8641d/u-boot.lds135
-rw-r--r--cpu/mpc86xx/cpu_init.c4
-rw-r--r--cpu/mpc86xx/interrupts.c51
-rw-r--r--cpu/mpc86xx/start.S85
-rw-r--r--cpu/mpc86xx/traps.c8
-rw-r--r--doc/README.sbc8641d28
-rw-r--r--drivers/fsl_pci_init.c46
-rw-r--r--drivers/pci_auto.c2
-rw-r--r--include/asm-ppc/immap_86xx.h16
-rw-r--r--include/asm-ppc/processor.h5
-rw-r--r--include/configs/sbc8641d.h604
19 files changed, 1538 insertions, 137 deletions
diff --git a/MAINTAINERS b/MAINTAINERS
index 865f6fe0e1..5b17739b58 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -179,6 +179,10 @@ Howard Gray <mvsensor@matrix-vision.de>
MVS1 MPC823
+Joe Hamman <joe.hamman@embeddedspecialties.com>
+
+ sbc8641d MPC8641D
+
Klaus Heydeck <heydeck@kieback-peter.de>
KUP4K MPC855
diff --git a/MAKEALL b/MAKEALL
index 129c14c9f9..7fb10b3648 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -335,6 +335,7 @@ LIST_85xx=" \
LIST_86xx=" \
MPC8641HPCN \
+ SBC8641D \
"
#########################################################################
diff --git a/Makefile b/Makefile
index eef51cc447..f51688961b 100644
--- a/Makefile
+++ b/Makefile
@@ -1866,6 +1866,8 @@ TQM8560_config: unconfig
MPC8641HPCN_config: unconfig
@$(MKCONFIG) $(@:_config=) ppc mpc86xx mpc8641hpcn
+sbc8641d_config: unconfig
+ @./mkconfig $(@:_config=) ppc mpc86xx sbc8641d
#########################################################################
## 74xx/7xx Systems
diff --git a/board/mpc8641hpcn/mpc8641hpcn.c b/board/mpc8641hpcn/mpc8641hpcn.c
index d2182aba5f..1bfbe88b5a 100644
--- a/board/mpc8641hpcn/mpc8641hpcn.c
+++ b/board/mpc8641hpcn/mpc8641hpcn.c
@@ -268,8 +268,8 @@ void pci_init_board(void)
* Activate ULI1575 legacy chip by performing a fake
* memory access. Needed to make ULI RTC work.
*/
- in_be32((unsigned *) CFG_PCI1_MEM_BASE
- + CFG_PCI1_MEM_SIZE - 0x1000000);
+ in_be32((unsigned *) ((char *)(CFG_PCI1_MEM_BASE
+ + CFG_PCI1_MEM_SIZE - 0x1000000)));
} else {
puts("PCI-EXPRESS 1: Disabled\n");
diff --git a/board/sbc8641d/Makefile b/board/sbc8641d/Makefile
new file mode 100644
index 0000000000..a90b725db4
--- /dev/null
+++ b/board/sbc8641d/Makefile
@@ -0,0 +1,52 @@
+#
+# (C) Copyright 2001
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := $(BOARD).o
+SOBJS := init.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+ rm -f $(OBJS) $(SOBJS)
+
+.PHONY: distclean
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude ($obj).depend
+
+#########################################################################
diff --git a/board/sbc8641d/config.mk b/board/sbc8641d/config.mk
new file mode 100644
index 0000000000..dd1754d2bc
--- /dev/null
+++ b/board/sbc8641d/config.mk
@@ -0,0 +1,30 @@
+# Copyright 2004 Freescale Semiconductor.
+# Modified by Jeff Brown
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# sbc8641 board
+# default CCSRBAR is at 0xff700000
+#
+TEXT_BASE = 0xfff00000
+
+PLATFORM_CPPFLAGS += -DCONFIG_MPC86xx=1
+PLATFORM_CPPFLAGS += -DCONFIG_MPC8641=1 -maltivec -mabi=altivec -msoft-float
diff --git a/board/sbc8641d/init.S b/board/sbc8641d/init.S
new file mode 100644
index 0000000000..c151d7eff8
--- /dev/null
+++ b/board/sbc8641d/init.S
@@ -0,0 +1,192 @@
+/*
+ * Copyright 2007 Wind River Systemes, Inc. <www.windriver.com>
+ * Copyright 2007 Embedded Specialties, Inc.
+ * Joe Hamman joe.hamman@embeddedspecialties.com
+ *
+ * Copyright 2004 Freescale Semiconductor.
+ * Jeff Brown
+ * Srikanth Srinivasan (srikanth.srinivasan@freescale.com)
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <ppc_asm.tmpl>
+#include <ppc_defs.h>
+#include <asm/cache.h>
+#include <asm/mmu.h>
+#include <config.h>
+#include <mpc86xx.h>
+
+/*
+ * LAW(Local Access Window) configuration:
+ *
+ * 0x0000_0000 0x0fff_ffff DDR1 256M
+ * 0x1000_0000 0x1fff_ffff DDR2 256M
+ * 0xe000_0000 0xffff_ffff LBC 512M
+ *
+ * Notes:
+ * CCSRBAR doesn't need a configured Local Access Window.
+ * If flash is 8M at default position (last 8M), no LAW needed.
+ */
+
+# DDR Bank 1
+# #define LAWBAR1 ((CFG_DDR_SDRAM_BASE>>12) & 0xffffff)
+# #define LAWAR1 (LAWAR_EN | LAWAR_TRGT_IF_DDR1 | (LAWAR_SIZE & LAWAR_SIZE_256M))
+
+# DDR Bank 2
+# #define LAWBAR2 ((CFG_DDR_SDRAM_BASE2>>12) & 0xffffff)
+# #define LAWAR2 (LAWAR_EN | LAWAR_TRGT_IF_DDR2 | (LAWAR_SIZE & LAWAR_SIZE_256M))
+
+# LBC
+# #define LAWBAR3 ((0xe0000000>>12) & 0xffffff)
+# #define LAWAR3 (LAWAR_EN & (LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_512M)))
+
+/*
+ * LAW (Local Access Window) configuration:
+ *
+ * 0x0000_0000 DDR 256M
+ * 0x1000_0000 DDR2 256M
+ * 0x8000_0000 PCI1 MEM 512M
+ * 0xa000_0000 PCI2 MEM 512M
+ * 0xc000_0000 RapidIO 512M
+ * 0xe200_0000 PCI1 IO 16M
+ * 0xe300_0000 PCI2 IO 16M
+ * 0xf800_0000 CCSRBAR 2M
+ * 0xfe00_0000 FLASH (boot bank) 32M
+ *
+ */
+
+#define LAWBAR1 ((CFG_DDR_SDRAM_BASE>>12) & 0xffffff)
+#define LAWAR1 (LAWAR_EN | LAWAR_TRGT_IF_DDR1 | (LAWAR_SIZE & LAWAR_SIZE_256M))
+
+#define LAWBAR2 ((CFG_PCI1_MEM_BASE>>12) & 0xffffff)
+#define LAWAR2 (LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_512M))
+
+#define LAWBAR3 ((CFG_PCI2_MEM_BASE>>12) & 0xffffff)
+#define LAWAR3 (~LAWAR_EN & (LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_512M)))
+
+#define LAWBAR4 ((0xf8000000>>12) & 0xffffff)
+#define LAWAR4 (LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_2M))
+
+#define LAWBAR5 ((CFG_PCI1_IO_BASE>>12) & 0xffffff)
+#define LAWAR5 (LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_16M))
+
+#define LAWBAR6 ((CFG_PCI2_IO_BASE>>12) & 0xffffff)
+#define LAWAR6 (~LAWAR_EN &( LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_16M)))
+
+#define LAWBAR7 ((0xfe000000 >>12) & 0xffffff)
+#define LAWAR7 (LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_32M))
+
+#define LAWBAR8 ((CFG_DDR_SDRAM_BASE2>>12) & 0xffffff)
+#define LAWAR8 (LAWAR_EN | LAWAR_TRGT_IF_DDR2 | (LAWAR_SIZE & LAWAR_SIZE_256M))
+
+#define LAWBAR9 ((CFG_RIO_MEM_BASE>>12) & 0xfffff)
+#define LAWAR9 (LAWAR_EN | LAWAR_TRGT_IF_RIO | (LAWAR_SIZE & LAWAR_SIZE_512M))
+
+ .section .bootpg, "ax"
+ .globl law_entry
+law_entry:
+ lis r7,CFG_CCSRBAR@h
+ ori r7,r7,CFG_CCSRBAR@l
+
+ addi r4,r7,0
+ addi r5,r7,0
+
+ /* Skip LAWAR0, start at LAWAR1 */
+ lis r6,LAWBAR1@h
+ ori r6,r6,LAWBAR1@l
+ stwu r6, 0xc28(r4)
+
+ lis r6,LAWAR1@h
+ ori r6,r6,LAWAR1@l
+ stwu r6, 0xc30(r5)
+
+ /* LAWBAR2, LAWAR2 */
+ lis r6,LAWBAR2@h
+ ori r6,r6,LAWBAR2@l
+ stwu r6, 0x20(r4)
+
+ lis r6,LAWAR2@h
+ ori r6,r6,LAWAR2@l
+ stwu r6, 0x20(r5)
+
+ /* LAWBAR3, LAWAR3 */
+ lis r6,LAWBAR3@h
+ ori r6,r6,LAWBAR3@l
+ stwu r6, 0x20(r4)
+
+ lis r6,LAWAR3@h
+ ori r6,r6,LAWAR3@l
+ stwu r6, 0x20(r5)
+
+ /* LAWBAR4, LAWAR4 */
+ lis r6,LAWBAR4@h
+ ori r6,r6,LAWBAR4@l
+ stwu r6, 0x20(r4)
+
+ lis r6,LAWAR4@h
+ ori r6,r6,LAWAR4@l
+ stwu r6, 0x20(r5)
+
+ /* LAWBAR5, LAWAR5 */
+ lis r6,LAWBAR5@h
+ ori r6,r6,LAWBAR5@l
+ stwu r6, 0x20(r4)
+
+ lis r6,LAWAR5@h
+ ori r6,r6,LAWAR5@l
+ stwu r6, 0x20(r5)
+
+ /* LAWBAR6, LAWAR6 */
+ lis r6,LAWBAR6@h
+ ori r6,r6,LAWBAR6@l
+ stwu r6, 0x20(r4)
+
+ lis r6,LAWAR6@h
+ ori r6,r6,LAWAR6@l
+ stwu r6, 0x20(r5)
+
+ /* LAWBAR7, LAWAR7 */
+ lis r6,LAWBAR7@h
+ ori r6,r6,LAWBAR7@l
+ stwu r6, 0x20(r4)
+
+ lis r6,LAWAR7@h
+ ori r6,r6,LAWAR7@l
+ stwu r6, 0x20(r5)
+
+ /* LAWBAR8, LAWAR8 */
+ lis r6,LAWBAR8@h
+ ori r6,r6,LAWBAR8@l
+ stwu r6, 0x20(r4)
+
+ lis r6,LAWAR8@h
+ ori r6,r6,LAWAR8@l
+ stwu r6, 0x20(r5)
+
+ /* LAWBAR9, LAWAR9 */
+ lis r6,LAWBAR9@h
+ ori r6,r6,LAWBAR9@l
+ stwu r6, 0x20(r4)
+
+ lis r6,LAWAR9@h
+ ori r6,r6,LAWAR9@l
+ stwu r6, 0x20(r5)
+
+ blr
diff --git a/board/sbc8641d/sbc8641d.c b/board/sbc8641d/sbc8641d.c
new file mode 100644
index 0000000000..7adc42faec
--- /dev/null
+++ b/board/sbc8641d/sbc8641d.c
@@ -0,0 +1,406 @@
+/*
+ * Copyright 2007 Wind River Systemes, Inc. <www.windriver.com>
+ * Copyright 2007 Embedded Specialties, Inc.
+ * Joe Hamman joe.hamman@embeddedspecialties.com
+ *
+ * Copyright 2004 Freescale Semiconductor.
+ * Jeff Brown
+ * Srikanth Srinivasan (srikanth.srinivasan@freescale.com)
+ *
+ * (C) Copyright 2002 Scott McNutt <smcnutt@artesyncp.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <pci.h>
+#include <asm/processor.h>
+#include <asm/immap_86xx.h>
+#include <asm/immap_fsl_pci.h>
+#include <spd.h>
+
+#if defined(CONFIG_OF_FLAT_TREE)
+#include <ft_build.h>
+extern void ft_cpu_setup (void *blob, bd_t * bd);
+#endif
+
+#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
+extern void ddr_enable_ecc (unsigned int dram_size);
+#endif
+
+#if defined(CONFIG_SPD_EEPROM)
+#include "spd_sdram.h"
+#endif
+
+void sdram_init (void);
+long int fixed_sdram (void);
+
+int board_early_init_f (void)
+{
+ return 0;
+}
+
+int checkboard (void)
+{
+ puts ("Board: Wind River SBC8641D\n");
+
+ return 0;
+}
+
+long int initdram (int board_type)
+{
+ long dram_size = 0;
+
+#if defined(CONFIG_SPD_EEPROM)
+ dram_size = spd_sdram ();
+#else
+ dram_size = fixed_sdram ();
+#endif
+
+#if defined(CFG_RAMBOOT)
+ puts (" DDR: ");
+ return dram_size;
+#endif
+
+#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
+ /*
+ * Initialize and enable DDR ECC.
+ */
+ ddr_enable_ecc (dram_size);
+#endif
+
+ puts (" DDR: ");
+ return dram_size;
+}
+
+#if defined(CFG_DRAM_TEST)
+int testdram (void)
+{
+ uint *pstart = (uint *) CFG_MEMTEST_START;
+ uint *pend = (uint *) CFG_MEMTEST_END;
+ uint *p;
+
+ puts ("SDRAM test phase 1:\n");
+ for (p = pstart; p < pend; p++)
+ *p = 0xaaaaaaaa;
+
+ for (p = pstart; p < pend; p++) {
+ if (*p != 0xaaaaaaaa) {
+ printf ("SDRAM test fails at: %08x\n", (uint) p);
+ return 1;
+ }
+ }
+
+ puts ("SDRAM test phase 2:\n");
+ for (p = pstart; p < pend; p++)
+ *p = 0x55555555;
+
+ for (p = pstart; p < pend; p++) {
+ if (*p != 0x55555555) {
+ printf ("SDRAM test fails at: %08x\n", (uint) p);
+ return 1;
+ }
+ }
+
+ puts ("SDRAM test passed.\n");
+ return 0;
+}
+#endif
+
+#if !defined(CONFIG_SPD_EEPROM)
+/*
+ * Fixed sdram init -- doesn't use serial presence detect.
+ */
+long int fixed_sdram (void)
+{
+#if !defined(CFG_RAMBOOT)
+ volatile immap_t *immap = (immap_t *) CFG_IMMR;
+ volatile ccsr_ddr_t *ddr = &immap->im_ddr1;
+
+ ddr->cs0_bnds = CFG_DDR_CS0_BNDS;
+ ddr->cs1_bnds = CFG_DDR_CS1_BNDS;
+ ddr->cs2_bnds = CFG_DDR_CS2_BNDS;
+ ddr->cs3_bnds = CFG_DDR_CS3_BNDS;
+ ddr->cs0_config = CFG_DDR_CS0_CONFIG;
+ ddr->cs1_config = CFG_DDR_CS1_CONFIG;
+ ddr->cs2_config = CFG_DDR_CS2_CONFIG;
+ ddr->cs3_config = CFG_DDR_CS3_CONFIG;
+ ddr->ext_refrec = CFG_DDR_EXT_REFRESH;
+ ddr->timing_cfg_0 = CFG_DDR_TIMING_0;
+ ddr->timing_cfg_1 = CFG_DDR_TIMING_1;
+ ddr->timing_cfg_2 = CFG_DDR_TIMING_2;
+ ddr->sdram_cfg_1 = CFG_DDR_CFG_1A;
+ ddr->sdram_cfg_2 = CFG_DDR_CFG_2;
+ ddr->sdram_mode_1 = CFG_DDR_MODE_1;
+ ddr->sdram_mode_2 = CFG_DDR_MODE_2;
+ ddr->sdram_mode_cntl = CFG_DDR_MODE_CTL;
+ ddr->sdram_interval = CFG_DDR_INTERVAL;
+ ddr->sdram_data_init = CFG_DDR_DATA_INIT;
+ ddr->sdram_clk_cntl = CFG_DDR_CLK_CTRL;
+
+ asm ("sync;isync");
+
+ udelay (500);
+
+ ddr->sdram_cfg_1 = CFG_DDR_CFG_1B;
+ asm ("sync; isync");
+
+ udelay (500);
+ ddr = &immap->im_ddr2;
+
+ ddr->cs0_bnds = CFG_DDR2_CS0_BNDS;
+ ddr->cs1_bnds = CFG_DDR2_CS1_BNDS;
+ ddr->cs2_bnds = CFG_DDR2_CS2_BNDS;
+ ddr->cs3_bnds = CFG_DDR2_CS3_BNDS;
+ ddr->cs0_config = CFG_DDR2_CS0_CONFIG;
+ ddr->cs1_config = CFG_DDR2_CS1_CONFIG;
+ ddr->cs2_config = CFG_DDR2_CS2_CONFIG;
+ ddr->cs3_config = CFG_DDR2_CS3_CONFIG;
+ ddr->ext_refrec = CFG_DDR2_EXT_REFRESH;
+ ddr->timing_cfg_0 = CFG_DDR2_TIMING_0;
+ ddr->timing_cfg_1 = CFG_DDR2_TIMING_1;
+ ddr->timing_cfg_2 = CFG_DDR2_TIMING_2;
+ ddr->sdram_cfg_1 = CFG_DDR2_CFG_1A;
+ ddr->sdram_cfg_2 = CFG_DDR2_CFG_2;
+ ddr->sdram_mode_1 = CFG_DDR2_MODE_1;
+ ddr->sdram_mode_2 = CFG_DDR2_MODE_2;
+ ddr->sdram_mode_cntl = CFG_DDR2_MODE_CTL;
+ ddr->sdram_interval = CFG_DDR2_INTERVAL;
+ ddr->sdram_data_init = CFG_DDR2_DATA_INIT;
+ ddr->sdram_clk_cntl = CFG_DDR2_CLK_CTRL;
+
+ asm ("sync;isync");
+
+ udelay (500);
+
+ ddr->sdram_cfg_1 = CFG_DDR2_CFG_1B;
+ asm ("sync; isync");
+
+ udelay (500);
+#endif
+ return CFG_SDRAM_SIZE * 1024 * 1024;
+}
+#endif /* !defined(CONFIG_SPD_EEPROM) */
+
+#if defined(CONFIG_PCI)
+/*
+ * Initialize PCI Devices, report devices found.
+ */
+
+#ifndef CONFIG_PCI_PNP
+static struct pci_config_table pci_fsl86xxads_config_table[] = {
+ {PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
+ PCI_IDSEL_NUMBER, PCI_ANY_ID,
+ pci_cfgfunc_config_device, {PCI_ENET0_IOADDR,
+ PCI_ENET0_MEMADDR,
+ PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER}},
+ {}
+};
+#endif
+
+static struct pci_controller pci1_hose = {
+#ifndef CONFIG_PCI_PNP
+ config_table:pci_mpc86xxcts_config_table
+#endif
+};
+#endif /* CONFIG_PCI */
+
+#ifdef CONFIG_PCI2
+static struct pci_controller pci2_hose;
+#endif /* CONFIG_PCI2 */
+
+int first_free_busno = 0;
+
+void pci_init_board(void)
+{
+ volatile immap_t *immap = (immap_t *) CFG_CCSRBAR;
+ volatile ccsr_gur_t *gur = &immap->im_gur;
+ uint devdisr = gur->devdisr;
+ uint io_sel = (gur->pordevsr & MPC86xx_PORDEVSR_IO_SEL) >> 16;
+
+#ifdef CONFIG_PCI1
+{
+ volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CFG_PCI1_ADDR;
+ extern void fsl_pci_init(struct pci_controller *hose);
+ struct pci_controller *hose = &pci1_hose;
+#ifdef DEBUG
+ uint host1_agent = (gur->porbmsr & MPC86xx_PORBMSR_HA) >> 17;
+ uint pex1_agent = (host1_agent == 0) || (host1_agent == 1);
+#endif
+ if ((io_sel == 2 || io_sel == 3 || io_sel == 5
+ || io_sel == 6 || io_sel == 7 || io_sel == 0xF)
+ && !(devdisr & MPC86xx_DEVDISR_PCIEX1)) {
+ debug("PCI-EXPRESS 1: %s \n", pex1_agent ? "Agent" : "Host");
+ debug("0x%08x=0x%08x ", &pci->pme_msg_det, pci->pme_msg_det);
+ if (pci->pme_msg_det) {
+ pci->pme_msg_det = 0xffffffff;
+ debug(" with errors. Clearing. Now 0x%08x",
+ pci->pme_msg_det);
+ }
+ debug("\n");
+
+ /* inbound */
+ pci_set_region(hose->regions + 0,
+ CFG_PCI_MEMORY_BUS,
+ CFG_PCI_MEMORY_PHYS,
+ CFG_PCI_MEMORY_SIZE,
+ PCI_REGION_MEM | PCI_REGION_MEMORY);
+
+ /* outbound memory */
+ pci_set_region(hose->regions + 1,
+ CFG_PCI1_MEM_BASE,
+ CFG_PCI1_MEM_PHYS,
+ CFG_PCI1_MEM_SIZE,
+ PCI_REGION_MEM);
+
+ /* outbound io */
+ pci_set_region(hose->regions + 2,
+ CFG_PCI1_IO_BASE,
+ CFG_PCI1_IO_PHYS,
+ CFG_PCI1_IO_SIZE,
+ PCI_REGION_IO);
+
+ hose->region_count = 3;
+
+ hose->first_busno=first_free_busno;
+ pci_setup_indirect(hose, (int) &pci->cfg_addr, (int) &pci->cfg_data);
+
+ fsl_pci_init(hose);
+
+ first_free_busno=hose->last_busno+1;
+ printf (" PCI-EXPRESS 1 on bus %02x - %02x\n",
+ hose->first_busno,hose->last_busno);
+
+ } else {
+ puts("PCI-EXPRESS 1: Disabled\n");
+ }
+}
+#else
+ puts("PCI-EXPRESS1: Disabled\n");
+#endif /* CONFIG_PCI1 */
+
+#ifdef CONFIG_PCI2
+{
+ volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CFG_PCI2_ADDR;
+ extern void fsl_pci_init(struct pci_controller *hose);
+ struct pci_controller *hose = &pci2_hose;
+
+
+ /* inbound */
+ pci_set_region(hose->regions + 0,
+ CFG_PCI_MEMORY_BUS,
+ CFG_PCI_MEMORY_PHYS,
+ CFG_PCI_MEMORY_SIZE,
+ PCI_REGION_MEM | PCI_REGION_MEMORY);
+
+ /* outbound memory */
+ pci_set_region(hose->regions + 1,
+ CFG_PCI2_MEM_BASE,
+ CFG_PCI2_MEM_PHYS,
+ CFG_PCI2_MEM_SIZE,
+ PCI_REGION_MEM);
+
+ /* outbound io */
+ pci_set_region(hose->regions + 2,
+ CFG_PCI2_IO_BASE,
+ CFG_PCI2_IO_PHYS,
+ CFG_PCI2_IO_SIZE,
+ PCI_REGION_IO);
+
+ hose->region_count = 3;
+
+ hose->first_busno=first_free_busno;
+ pci_setup_indirect(hose, (int) &pci->cfg_addr, (int) &pci->cfg_data);
+
+ fsl_pci_init(hose);
+
+ first_free_busno=hose->last_busno+1;
+ printf (" PCI-EXPRESS 2 on bus %02x - %02x\n",
+ hose->first_busno,hose->last_busno);
+}
+#else
+ puts("PCI-EXPRESS 2: Disabled\n");
+#endif /* CONFIG_PCI2 */
+
+}
+
+#if defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup (void *blob, bd_t * bd)
+{
+ u32 *p;
+ int len;
+
+ ft_cpu_setup (blob, bd);
+
+ p = ft_get_prop (blob, "/memory/reg", &len);
+ if (p != NULL) {
+ *p++ = cpu_to_be32 (bd->bi_memstart);
+ *p = cpu_to_be32 (bd->bi_memsize);
+ }
+}
+#endif
+
+void sbc8641d_reset_board (void)
+{
+ puts ("Resetting board....\n");
+}
+
+/*
+ * get_board_sys_clk
+ * Clock is fixed at 1GHz on this board. Used for CONFIG_SYS_CLK_FREQ
+ */
+
+unsigned long get_board_sys_clk (ulong dummy)
+{
+ int i;
+ ulong val = 0;
+
+ i = 5;
+ i &= 0x07;
+
+ switch (i) {
+ case 0:
+ val = 33000000;
+ break;
+ case 1:
+ val = 40000000;
+ break;
+ case 2:
+ val = 50000000;
+ break;
+ case 3:
+ val = 66000000;
+ break;
+ case 4:
+ val = 83000000;
+ break;
+ case 5:
+ val = 100000000;
+ break;
+ case 6:
+ val = 134000000;
+ break;
+ case 7:
+ val = 166000000;
+ break;
+ }
+
+ return val;
+}
diff --git a/board/sbc8641d/u-boot.lds b/board/sbc8641d/u-boot.lds
new file mode 100644
index 0000000000..fd0f35039f
--- /dev/null
+++ b/board/sbc8641d/u-boot.lds
@@ -0,0 +1,135 @@
+/*
+ * Copyright 2006, 2007 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+
+SECTIONS
+{
+
+ /* Read-only sections, merged into text segment: */
+ .interp : { *(.interp) }
+ .hash : { *(.hash) }
+ .dynsym : { *(.dynsym) }
+ .dynstr : { *(.dynstr) }
+ .rel.text : { *(.rel.text) }
+ .rela.text : { *(.rela.text) }
+ .rel.data : { *(.rel.data) }
+ .rela.data : { *(.rela.data) }
+ .rel.rodata : { *(.rel.rodata) }
+ .rela.rodata : { *(.rela.rodata) }
+ .rel.got : { *(.rel.got) }
+ .rela.got : { *(.rela.got) }
+ .rel.ctors : { *(.rel.ctors) }
+ .rela.ctors : { *(.rela.ctors) }
+ .rel.dtors : { *(.rel.dtors) }
+ .rela.dtors : { *(.rela.dtors) }
+ .rel.bss : { *(.rel.bss) }
+ .rela.bss : { *(.rela.bss) }
+ .rel.plt : { *(.rel.plt) }
+ .rela.plt : { *(.rela.plt) }
+ .init : { *(.init) }
+ .plt : { *(.plt) }
+ .text :
+ {
+ cpu/mpc86xx/start.o (.text)
+ board/sbc8641d/init.o (.bootpg)
+ cpu/mpc86xx/traps.o (.text)
+ cpu/mpc86xx/interrupts.o (.text)
+ cpu/mpc86xx/cpu_init.o (.text)
+ cpu/mpc86xx/cpu.o (.text)
+ cpu/mpc86xx/speed.o (.text)
+ common/dlmalloc.o (.text)
+ lib_generic/crc32.o (.text)
+ lib_ppc/extable.o (.text)
+ lib_generic/zlib.o (.text)
+ *(.text)
+ *(.fixup)
+ *(.got1)
+ }
+ _etext = .;
+ PROVIDE (etext = .);
+ .rodata :
+ {
+ *(.rodata)
+ *(.rodata1)
+ *(.rodata.str1.4)
+ *(.eh_frame)
+ }
+ .fini : { *(.fini) } =0
+ .ctors : { *(.ctors) }
+ .dtors : { *(.dtors) }
+
+ /* Read-write section, merged into data segment: */
+ . = (. + 0x00FF) & 0xFFFFFF00;
+ _erotext = .;
+ PROVIDE (erotext = .);
+ .reloc :
+ {
+ *(.got)
+ _GOT2_TABLE_ = .;
+ *(.got2)
+ _FIXUP_TABLE_ = .;
+ *(.fixup)
+ }
+ __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
+ __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
+
+ .data :
+ {
+ *(.data)
+ *(.data1)
+ *(.sdata)
+ *(.sdata2)
+ *(.dynamic)
+ CONSTRUCTORS
+ }
+ _edata = .;
+ PROVIDE (edata = .);
+
+ . = .;
+ __u_boot_cmd_start = .;
+ .u_boot_cmd : { *(.u_boot_cmd) }
+ __u_boot_cmd_end = .;
+
+ . = .;
+ __start___ex_table = .;
+ __ex_table : { *(__ex_table) }
+ __stop___ex_table = .;
+
+ . = ALIGN(256);
+ __init_begin = .;
+ .text.init : { *(.text.init) }
+ .data.init : { *(.data.init) }
+ . = ALIGN(256);
+ __init_end = .;
+
+ __bss_start = .;
+ .bss :
+ {
+ *(.sbss) *(.scommon)
+ *(.dynbss)
+ *(.bss)
+ *(COMMON)
+ }
+ _end = . ;
+ PROVIDE (end = .);
+}
diff --git a/cpu/mpc86xx/cpu_init.c b/cpu/mpc86xx/cpu_init.c
index 4673d05e71..c8e4666694 100644
--- a/cpu/mpc86xx/cpu_init.c
+++ b/cpu/mpc86xx/cpu_init.c
@@ -104,8 +104,8 @@ void cpu_init_f(void)
/* enable the timebase bit in HID0 */
set_hid0(get_hid0() | 0x4000000);
- /* enable SYNCBE | ABE bits in HID1 */
- set_hid1(get_hid1() | 0x00000C00);
+ /* enable EMCP, SYNCBE | ABE bits in HID1 */
+ set_hid1(get_hid1() | 0x80000C00);
}
/*
diff --git a/cpu/mpc86xx/interrupts.c b/cpu/mpc86xx/interrupts.c
index 08e0675fee..d9f634fdab 100644
--- a/cpu/mpc86xx/interrupts.c
+++ b/cpu/mpc86xx/interrupts.c
@@ -8,7 +8,7 @@
* (C) Copyright 2003 Motorola Inc. (MPC85xx port)
* Xianghua Xiao (X.Xiao@motorola.com)
*
- * (C) Copyright 2004 Freescale Semiconductor. (MPC86xx Port)
+ * (C) Copyright 2004, 2007 Freescale Semiconductor. (MPC86xx Port)
* Jeff Brown
* Srikanth Srinivasan (srikanth.srinivasan@freescale.com)
*
@@ -80,25 +80,10 @@ int interrupt_init(void)
{
int ret;
- /*
- * The IRQ0 on Rev 2 is pulled high (low in Rev 1.x) to
- * implement PEX10 errata. As INT is active high, it
- * will cause core to take 0x500 interrupt.
- *
- * Due to the PIC's default pass through mode, as soon
- * as interrupts are enabled (MSR[EE] = 1), an interrupt
- * will be taken and u-boot will hang. This is due to a
- * hardware change (per an errata fix) on new revisions
- * of the board with Rev 2.x parts.
- *
- * Setting the PIC to mixed mode prevents the hang.
- */
- if ((get_svr() & 0xf0) == 0x20) {
- volatile immap_t *immr = (immap_t *)CFG_IMMR;
- immr->im_pic.gcr = MPC86xx_PICGCR_RST;
- while (immr->im_pic.gcr & MPC86xx_PICGCR_RST);
- immr->im_pic.gcr = MPC86xx_PICGCR_MODE;
- }
+ volatile immap_t *immr = (immap_t *)CFG_IMMR;
+ immr->im_pic.gcr = MPC86xx_PICGCR_RST;
+ while (immr->im_pic.gcr & MPC86xx_PICGCR_RST);
+ immr->im_pic.gcr = MPC86xx_PICGCR_MODE;
/* call cpu specific function from $(CPU)/interrupts.c */
ret = interrupt_init_cpu(&decrementer_count);
@@ -119,6 +104,30 @@ int interrupt_init(void)
get_msr(),
get_dec());
+#ifdef CONFIG_INTERRUPTS
+ volatile ccsr_pic_t *pic = &immr->im_pic;
+
+ pic->iivpr1 = 0x810001; /* 50220 enable mcm interrupts */
+ debug("iivpr1@%x = %x\n", &pic->iivpr1, pic->iivpr1);
+
+ pic->iivpr2 = 0x810002; /* 50240 enable ddr interrupts */
+ debug("iivpr2@%x = %x\n", &pic->iivpr2, pic->iivpr2);
+
+ pic->iivpr3 = 0x810003; /* 50260 enable lbc interrupts */
+ debug("iivpr3@%x = %x\n", &pic->iivpr3, pic->iivpr3);
+
+#if defined(CONFIG_PCI1) || defined(CONFIG_PCIE1)
+ pic->iivpr8 = 0x810008; /* enable pcie1 interrupts */
+ debug("iivpr8@%x = %x\n", &pic->iivpr8, pic->iivpr8);
+#endif
+#if defined(CONFIG_PCI2) || defined(CONFIG_PCIE2)
+ pic->iivpr9 = 0x810009; /* enable pcie2 interrupts */
+ debug("iivpr9@%x = %x\n", &pic->iivpr9, pic->iivpr9);
+#endif
+
+ pic->ctpr = 0; /* 40080 clear current task priority register */
+#endif
+
return 0;
}
@@ -158,8 +167,6 @@ void timer_interrupt(struct pt_regs *regs)
timestamp++;
- ppcDcbf((unsigned long)&timestamp);
-
/* Restore Decrementer Count */
set_dec(decrementer_count);
diff --git a/cpu/mpc86xx/start.S b/cpu/mpc86xx/start.S
index 412745bdae..c83310a333 100644
--- a/cpu/mpc86xx/start.S
+++ b/cpu/mpc86xx/start.S
@@ -1,5 +1,5 @@
/*
- * Copyright 2004 Freescale Semiconductor.
+ * Copyright 2004, 2007 Freescale Semiconductor.
* Srikanth Srinivasan <srikanth.srinivaan@freescale.com>
*
* See file CREDITS for list of people who contributed to this
@@ -44,11 +44,9 @@
#define CONFIG_IDENT_STRING ""
#endif
-/* We don't want the MMU yet.
-*/
-#undef MSR_KERNEL
-/* Machine Check and Recoverable Interr. */
-#define MSR_KERNEL ( MSR_ME | MSR_RI )
+/*
+ * Need MSR_DR | MSR_IR enabled to access I/O (printf) in exceptions
+ */
/*
* Set up GOT: Global Offset Table
@@ -195,17 +193,21 @@ boot_warm:
bl secondary_cpu_setup
#endif
+1:
+#ifdef CFG_RAMBOOT
/* disable everything */
-1: li r0, 0
+ li r0, 0
mtspr HID0, r0
sync
mtmsr 0
+#endif
+
bl invalidate_bats
sync
#ifdef CFG_L2
/* init the L2 cache */
- addis r3, r0, L2_INIT@h
+ lis r3, L2_INIT@h
ori r3, r3, L2_INIT@l
mtspr l2cr, r3
/* invalidate the L2 cache */
@@ -241,69 +243,9 @@ in_flash:
bl setup_ccsrbar
#endif
-
- /* -- MPC8641 Rev 1.0 MCM Errata fixups -- */
-
- /* skip fixups if not Rev 1.0 */
- mfspr r4, SVR
- rlwinm r4,r4,0,24,31
- cmpwi r4,0x10
- bne 1f
-
- lis r3,MCM_ABCR@ha
- lwz r4,MCM_ABCR@l(r3) /* ABCR -> r4 */
-
- /* set ABCR[A_STRM_CNT] = 0 */
- rlwinm r4,r4,0,0,29
-
- /* set ABCR[ARB_POLICY] to 0x1 (round-robin) */
- addi r0,r0,1
- rlwimi r4,r0,12,18,19
-
- stw r4,MCM_ABCR@l(r3) /* r4 -> ABCR */
- sync
-
- /* Set DBCR[ERD_DIS] */
- lis r3,MCM_DBCR@ha
- lwz r4,MCM_DBCR@l(r3)
- oris r4, r4, 0x4000
- stw r4,MCM_DBCR@l(r3)
- sync
-1:
/* setup the law entries */
bl law_entry
sync
-
-
-#if (EMULATOR_RUN == 1)
- /* On the emulator we want to adjust these ASAP */
- /* otherwise things are sloooow */
- /* Setup OR0 (LALE FIX)*/
- lis r3, CFG_CCSRBAR@h
- ori r3, r3, 0x5004
- li r4, 0x0FF3
- stw r4, 0(r3)
- sync
-
- /* Setup LCRR */
- lis r3, CFG_CCSRBAR@h
- ori r3, r3, 0x50D4
- lis r4, 0x8000
- ori r4, r4, 0x0002
- stw r4, 0(r3)
- sync
-#endif
-#if 1
- /* make sure timer enabled in guts register too */
- lis r3, CFG_CCSRBAR@h
- oris r3,r3, 0xE
- ori r3,r3,0x0070
- lwz r4, 0(r3)
- lis r5,0xFFFC
- ori r5,r5,0x5FFF
- and r4,r4,r5
- stw r4,0(r3)
-#endif
/*
* Cache must be enabled here for stack-in-cache trick.
* This means we need to enable the BATS.
@@ -346,8 +288,6 @@ in_flash:
#ifdef RUN_DIAG
- /* Sri: Code to run the diagnostic automatically */
-
/* Load PX_AUX register address in r4 */
lis r4, 0xf810
ori r4, r4, 0x6
@@ -392,6 +332,7 @@ diag_done:
.globl invalidate_bats
invalidate_bats:
+ li r0, 0
/* invalidate BATs */
mtspr IBAT0U, r0
mtspr IBAT1U, r0
@@ -1040,6 +981,7 @@ trap_init:
mfmsr r7
li r8,MSR_IP
andc r7,r7,r8
+ ori r7,r7,MSR_ME /* Enable Machine Check */
mtmsr r7
mtlr r4 /* restore link register */
@@ -1224,8 +1166,9 @@ secondary_cpu_setup:
sync
isync
- /*SYNCBE|ABE in HID1*/
+ /* MCP|SYNCBE|ABE in HID1 */
mfspr r4, HID1
+ oris r4, r4, 0x8000
ori r4, r4, 0x0C00
mtspr HID1, r4
sync
diff --git a/cpu/mpc86xx/traps.c b/cpu/mpc86xx/traps.c
index fab1975834..c84bfbf6aa 100644
--- a/cpu/mpc86xx/traps.c
+++ b/cpu/mpc86xx/traps.c
@@ -130,8 +130,11 @@ MachineCheckException(struct pt_regs *regs)
printf("Machine check in kernel mode.\n");
printf("Caused by (from msr): ");
printf("regs %p ", regs);
- switch (regs->msr & 0x000F0000) {
- case (0x80000000 >> 12):
+ switch ( regs->msr & 0x001F0000) {
+ case (0x80000000>>11):
+ printf("MSS error. MSSSR0: %08x\n", mfspr(SPRN_MSSSR0));
+ break;
+ case (0x80000000>>12):
printf("Machine check signal - probably due to mm fault\n"
"with mmu off\n");
break;
@@ -209,6 +212,7 @@ UnknownException(struct pt_regs *regs)
if (debugger_exception_handler && (*debugger_exception_handler) (regs))
return;
#endif
+ printf("UnknownException regs@%x\n", regs);
printf("Bad trap at PC: %lx, SR: %lx, vector=%lx\n",
regs->nip, regs->msr, regs->trap);
_exception(0, regs);
diff --git a/doc/README.sbc8641d b/doc/README.sbc8641d
new file mode 100644
index 0000000000..a051466a11
--- /dev/null
+++ b/doc/README.sbc8641d
@@ -0,0 +1,28 @@
+Wind River SBC8641D reference board
+===========================
+
+Created 06/14/2007 Joe Hamman
+Copyright 2007, Embedded Specialties, Inc.
+Copyright 2007 Wind River Systemes, Inc.
+-----------------------------
+
+1. Building U-Boot
+------------------
+The SBC8641D code is known to build using ELDK 4.1.
+
+ $ make sbc8641d_config
+ Configuring for sbc8641d board...
+
+ $ make
+
+
+2. Switch and Jumper Settings
+-----------------------------
+All Jumpers & Switches are in their default positions. Please refer to
+the board documentation for details. Some settings control CPU voltages
+and settings may change with board revisions.
+
+3. Known limitations
+--------------------
+PCI:
+ The PCI command may hang if no boards are present in either slot.
diff --git a/drivers/fsl_pci_init.c b/drivers/fsl_pci_init.c
index 1d1f6df997..1084dc6b78 100644
--- a/drivers/fsl_pci_init.c
+++ b/drivers/fsl_pci_init.c
@@ -15,7 +15,7 @@
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
-#define DEBUG
+
#include <common.h>
#ifdef CONFIG_FSL_PCI_INIT
@@ -93,7 +93,11 @@ fsl_pci_init(struct pci_controller *hose)
hose->current_busno = hose->first_busno;
pci->pedr = 0xffffffff; /* Clear any errors */
- pci->peer = 0xffffffff; /* Enable Error Interupts */
+ pci->peer = ~0x20140; /* Enable All Error Interupts except
+ * - Master abort (pci)
+ * - Master PERR (pci)
+ * - ICCA (PCIe)
+ */
pci_hose_read_config_dword (hose, dev, PCI_DCR, &temp32);
temp32 |= 0xf000e; /* set URR, FER, NFER (but not CER) */
pci_hose_write_config_dword(hose, dev, PCI_DCR, temp32);
@@ -108,7 +112,7 @@ fsl_pci_init(struct pci_controller *hose)
if (!enabled) {
debug("....PCIE link error. Skipping scan."
- "LTSSM=0x%02x\n", temp16);
+ "LTSSM=0x%02x\n", ltssm);
hose->last_busno = hose->first_busno;
return;
}
@@ -118,61 +122,41 @@ fsl_pci_init(struct pci_controller *hose)
#ifdef DEBUG
pci_hose_read_config_word(hose, dev, PCI_LSR, &temp16);
neg_link_w = (temp16 & 0x3f0 ) >> 4;
- debug("...PCIE LTSSM=0x%x, Negotiated link width=%d\n",
+ printf("...PCIE LTSSM=0x%x, Negotiated link width=%d\n",
ltssm, neg_link_w);
#endif
hose->current_busno++; /* Start scan with secondary */
pciauto_prescan_setup_bridge(hose, dev, hose->current_busno);
- } else {
-#if 0
-/* done in pci_hose_config_device() */
- pci_hose_read_config_word(hose, dev, PCI_COMMAND, &temp16);
- temp16 |= PCI_COMMAND_SERR | PCI_COMMAND_MASTER |
- PCI_COMMAND_MEMORY | PCI_COMMAND_IO;
- pci_hose_write_config_word(hose, dev, PCI_COMMAND, temp16);
- pci_hose_write_config_word(hose, dev, PCI_STATUS, 0xffff);
- pci_hose_write_config_byte(hose, dev, PCI_LATENCY_TIMER, 0x80);
-#endif
}
/* Call setup to allocate PCSRBAR window */
pciauto_setup_device(hose, dev, 1, hose->pci_mem,
hose->pci_prefetch, hose->pci_io);
-
+#ifndef CONFIG_PCI_NOSCAN
printf (" Scanning PCI bus %02x\n", hose->current_busno);
hose->last_busno = pci_hose_scan_bus(hose,hose->current_busno);
if ( bridge ) { /* update limit regs and subordinate busno */
pciauto_postscan_setup_bridge(hose, dev, hose->last_busno);
}
+#else
+ hose->last_busno = hose->current_busno;
+#endif
/* Clear all error indications */
- if (pci->pme_msg_det && pci->pme_msg_det != 0xffffffff) {
- debug("pci_fsl_init: pme_msg_det@%x=%x. Clearing\n",
- &pci->pme_msg_det, pci->pme_msg_det);
- pci->pme_msg_det = 0xffffffff;
- }
-
- if (pci->pedr) {
- debug("pci_fsl_init: pedr@%x=%x. Clearing\n",
- &pci->pedr, pci->pedr);
- pci->pedr = 0xffffffff;
- }
+ pci->pme_msg_det = 0xffffffff;
+ pci->pedr = 0xffffffff;
pci_hose_read_config_word (hose, dev, PCI_DSR, &temp16);
if (temp16) {
- debug("pci_fsl_init: PCI_DSR@%x=%x. Clearing\n",
- PCI_DSR, temp16);
pci_hose_write_config_word(hose, dev,
- PCI_DSR, 0xffff);
+ PCI_DSR, 0xffff);
}
pci_hose_read_config_word (hose, dev, PCI_SEC_STATUS, &temp16);
if (temp16) {
- debug("pci_fsl_init: PCI_SEC_STATUS@%x=%x. Clearing\n",
- PCI_SEC_STATUS, temp16);
pci_hose_write_config_word(hose, dev, PCI_SEC_STATUS, 0xffff);
}
}
diff --git a/drivers/pci_auto.c b/drivers/pci_auto.c
index a3c609ba49..2378553be5 100644
--- a/drivers/pci_auto.c
+++ b/drivers/pci_auto.c
@@ -94,7 +94,7 @@ void pciauto_setup_device(struct pci_controller *hose,
pci_hose_read_config_dword(hose, dev, PCI_COMMAND, &cmdstat);
cmdstat = (cmdstat & ~(PCI_COMMAND_IO | PCI_COMMAND_MEMORY)) | PCI_COMMAND_MASTER;
- for (bar = PCI_BASE_ADDRESS_0; bar <= PCI_BASE_ADDRESS_0 + (bars_num*4); bar += 4) {
+ for (bar = PCI_BASE_ADDRESS_0; bar < PCI_BASE_ADDRESS_0 + (bars_num*4); bar += 4) {
/* Tickle the BAR and get the response */
pci_hose_write_config_dword(hose, dev, bar, 0xffffffff);
pci_hose_read_config_dword(hose, dev, bar, &bar_response);
diff --git a/include/asm-ppc/immap_86xx.h b/include/asm-ppc/immap_86xx.h
index 0e3fc3403d..169725b923 100644
--- a/include/asm-ppc/immap_86xx.h
+++ b/include/asm-ppc/immap_86xx.h
@@ -1257,9 +1257,12 @@ typedef struct ccsr_gur {
uint porpllsr; /* 0xe0000 - POR PLL ratio status register */
uint porbmsr; /* 0xe0004 - POR boot mode status register */
#define MPC86xx_PORBMSR_HA 0x00060000
+#define MPC85xx_PORBMSR_HA 0x00070000
uint porimpscr; /* 0xe0008 - POR I/O impedance status and control register */
uint pordevsr; /* 0xe000c - POR I/O device status regsiter */
-#define MPC86xx_PORDEVSR_IO_SEL 0x000F0000
+#define MPC86xx_PORDEVSR_IO_SEL 0x000F0000
+#define MPC85xx_PORDEVSR_IO_SEL 0x00380000 /* 85xx platform type */
+#define MPC86xx_PORDEVSR_CORE1TE 0x00000080 /* ASMP (Core1 addr trans) */
uint pordbgmsr; /* 0xe0010 - POR debug mode status register */
char res1[12];
uint gpporcr; /* 0xe0020 - General-purpose POR configuration register */
@@ -1273,8 +1276,11 @@ typedef struct ccsr_gur {
uint pmuxcr; /* 0xe0060 - Alternate function signal multiplex control */
char res6[12];
uint devdisr; /* 0xe0070 - Device disable control */
-#define MPC86xx_DEVDISR_PCIEX1 0x80000000
-#define MPC86xx_DEVDISR_PCIEX2 0x40000000
+#define MPC86xx_DEVDISR_PCIEX1 0x80000000
+#define MPC86xx_DEVDISR_PCIEX2 0x40000000
+#define MPC86xx_DEVDISR_PCI1 0x80000000
+#define MPC86xx_DEVDISR_PCIE1 0x40000000
+#define MPC86xx_DEVDISR_PCIE2 0x20000000
char res7[12];
uint powmgtcsr; /* 0xe0080 - Power management status and control register */
char res8[12];
@@ -1282,7 +1288,9 @@ typedef struct ccsr_gur {
char res9[12];
uint pvr; /* 0xe00a0 - Processor version register */
uint svr; /* 0xe00a4 - System version register */
- char res10[3416];
+ char res10a[1880];
+ uint clkdvdr; /* 0xe0800 - Clock Divide register */
+ char res10b[1532];
uint clkocr; /* 0xe0e00 - Clock out select register */
char res11[12];
uint ddrdllcr; /* 0xe0e10 - DDR DLL control register */
diff --git a/include/asm-ppc/processor.h b/include/asm-ppc/processor.h
index 71e2e847a4..9be5a279e2 100644
--- a/include/asm-ppc/processor.h
+++ b/include/asm-ppc/processor.h
@@ -464,7 +464,8 @@
#define ESR_ST 0x00800000 /* Store Operation */
#if defined(CONFIG_MPC86xx)
-#define SPRN_MSSCRO 0x3f6
+#define SPRN_MSSCR0 0x3f6
+#define SPRN_MSSSR0 0x3f7
#endif
@@ -531,7 +532,7 @@
#define LR SPRN_LR
#define MBAR SPRN_MBAR /* System memory base address */
#if defined(CONFIG_MPC86xx)
-#define MSSCR0 SPRN_MSSCRO
+#define MSSCR0 SPRN_MSSCR0
#endif
#if defined(CONFIG_E500) || defined(CONFIG_MPC86xx)
#define PIR SPRN_PIR
diff --git a/include/configs/sbc8641d.h b/include/configs/sbc8641d.h
new file mode 100644
index 0000000000..68d31ca1db
--- /dev/null
+++ b/include/configs/sbc8641d.h
@@ -0,0 +1,604 @@
+/*
+ * Copyright 2007 Wind River Systems <www.windriver.com>
+ * Copyright 2007 Embedded Specialties, Inc.
+ * Joe Hamman <joe.hamman@embeddedspecialties.com>
+ *
+ * Copyright 2006 Freescale Semiconductor.
+ *
+ * Srikanth Srinivasan (srikanth.srinivasan@freescale.com)
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * SBC8641D board configuration file
+ *
+ * Make sure you change the MAC address and other network params first,
+ * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file.
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* High Level Configuration Options */
+#define CONFIG_MPC86xx 1 /* MPC86xx */
+#define CONFIG_MPC8641 1 /* MPC8641 specific */
+#define CONFIG_SBC8641D 1 /* SBC8641D board specific */
+#define CONFIG_NUM_CPUS 2 /* Number of CPUs in the system */
+#define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */
+
+#ifdef RUN_DIAG
+#define CFG_DIAG_ADDR 0xff800000
+#endif
+
+#define CFG_RESET_ADDRESS 0xfff00100
+
+#define CONFIG_PCI 1 /* Enable PCIE */
+#define CONFIG_PCI1 1 /* PCIE controler 1 (slot 1) */
+#define CONFIG_PCI2 1 /* PCIE controler 2 (slot 2) */
+#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
+
+#define CONFIG_TSEC_ENET /* tsec ethernet support */
+#define CONFIG_ENV_OVERWRITE
+
+#undef CONFIG_SPD_EEPROM /* Do not use SPD EEPROM for DDR setup*/
+#undef CONFIG_DDR_DLL /* possible DLL fix needed */
+#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
+#undef CONFIG_DDR_ECC /* only for ECC DDR module */
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
+#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
+#define CONFIG_NUM_DDR_CONTROLLERS 2
+#define CACHE_LINE_INTERLEAVING 0x20000000
+#define PAGE_INTERLEAVING 0x21000000
+#define BANK_INTERLEAVING 0x22000000
+#define SUPER_BANK_INTERLEAVING 0x23000000
+
+
+#define CONFIG_ALTIVEC 1
+
+/*
+ * L2CR setup -- make sure this is right for your board!
+ */
+#define CFG_L2
+#define L2_INIT 0
+#define L2_ENABLE (L2CR_L2E)
+
+#ifndef CONFIG_SYS_CLK_FREQ
+#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0)
+#endif
+
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
+
+#undef CFG_DRAM_TEST /* memory test, takes time */
+#define CFG_MEMTEST_START 0x00200000 /* memtest region */
+#define CFG_MEMTEST_END 0x00400000
+
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
+#define CFG_CCSRBAR 0xf8000000 /* relocated CCSRBAR */
+#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
+
+#define CFG_PCI1_ADDR (CFG_CCSRBAR+0x8000)
+#define CFG_PCI2_ADDR (CFG_CCSRBAR+0x9000)
+
+/*
+ * DDR Setup
+ */
+#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */
+#define CFG_DDR_SDRAM_BASE2 0x10000000 /* DDR bank 2 */
+#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
+#define CFG_SDRAM_BASE2 CFG_DDR_SDRAM_BASE2
+#define CONFIG_VERY_BIG_RAM
+
+#define MPC86xx_DDR_SDRAM_CLK_CNTL
+
+#if defined(CONFIG_SPD_EEPROM)
+ /*
+ * Determine DDR configuration from I2C interface.
+ */
+ #define SPD_EEPROM_ADDRESS1 0x51 /* DDR DIMM */
+ #define SPD_EEPROM_ADDRESS2 0x52 /* DDR DIMM */
+ #define SPD_EEPROM_ADDRESS3 0x53 /* DDR DIMM */
+ #define SPD_EEPROM_ADDRESS4 0x54 /* DDR DIMM */
+
+#else
+ /*
+ * Manually set up DDR1 & DDR2 parameters
+ */
+
+ #define CFG_SDRAM_SIZE 512 /* DDR is 512MB */
+
+ #define CFG_DDR_CS0_BNDS 0x0000000F
+ #define CFG_DDR_CS1_BNDS 0x00000000
+ #define CFG_DDR_CS2_BNDS 0x00000000
+ #define CFG_DDR_CS3_BNDS 0x00000000
+ #define CFG_DDR_CS0_CONFIG 0x80010102
+ #define CFG_DDR_CS1_CONFIG 0x00000000
+ #define CFG_DDR_CS2_CONFIG 0x00000000
+ #define CFG_DDR_CS3_CONFIG 0x00000000
+ #define CFG_DDR_EXT_REFRESH 0x00000000
+ #define CFG_DDR_TIMING_0 0x00220802
+ #define CFG_DDR_TIMING_1 0x38377322
+ #define CFG_DDR_TIMING_2 0x002040c7
+ #define CFG_DDR_CFG_1A 0x43008008
+ #define CFG_DDR_CFG_2 0x24401000
+ #define CFG_DDR_MODE_1 0x23c00542
+ #define CFG_DDR_MODE_2 0x00000000
+ #define CFG_DDR_MODE_CTL 0x00000000
+ #define CFG_DDR_INTERVAL 0x05080100
+ #define CFG_DDR_DATA_INIT 0x00000000
+ #define CFG_DDR_CLK_CTRL 0x03800000
+ #define CFG_DDR_CFG_1B 0xC3008008
+
+ #define CFG_DDR2_CS0_BNDS 0x0010001F
+ #define CFG_DDR2_CS1_BNDS 0x00000000
+ #define CFG_DDR2_CS2_BNDS 0x00000000
+ #define CFG_DDR2_CS3_BNDS 0x00000000
+ #define CFG_DDR2_CS0_CONFIG 0x80010102
+ #define CFG_DDR2_CS1_CONFIG 0x00000000
+ #define CFG_DDR2_CS2_CONFIG 0x00000000
+ #define CFG_DDR2_CS3_CONFIG 0x00000000
+ #define CFG_DDR2_EXT_REFRESH 0x00000000
+ #define CFG_DDR2_TIMING_0 0x00220802
+ #define CFG_DDR2_TIMING_1 0x38377322
+ #define CFG_DDR2_TIMING_2 0x002040c7
+ #define CFG_DDR2_CFG_1A 0x43008008
+ #define CFG_DDR2_CFG_2 0x24401000
+ #define CFG_DDR2_MODE_1 0x23c00542
+ #define CFG_DDR2_MODE_2 0x00000000
+ #define CFG_DDR2_MODE_CTL 0x00000000
+ #define CFG_DDR2_INTERVAL 0x05080100
+ #define CFG_DDR2_DATA_INIT 0x00000000
+ #define CFG_DDR2_CLK_CTRL 0x03800000
+ #define CFG_DDR2_CFG_1B 0xC3008008
+
+
+#endif
+
+/* #define CFG_ID_EEPROM 1
+#define ID_EEPROM_ADDR 0x57 */
+
+/*
+ * The SBC8641D contains 16MB flash space at ff000000.
+ */
+#define CFG_FLASH_BASE 0xff000000 /* start of FLASH 16M */
+
+/* Flash */
+#define CFG_BR0_PRELIM 0xff001001 /* port size 16bit */
+#define CFG_OR0_PRELIM 0xff006e65 /* 16MB Boot Flash area */
+
+/* 64KB EEPROM */
+#define CFG_BR1_PRELIM 0xf0000801 /* port size 16bit */
+#define CFG_OR1_PRELIM 0xffff6e65 /* 64K EEPROM area */
+
+/* EPLD - User switches, board id, LEDs */
+#define CFG_BR2_PRELIM 0xf1000801 /* port size 16bit */
+#define CFG_OR2_PRELIM 0xfff06e65 /* EPLD (switches, board ID, LEDs) area */
+
+/* Local bus SDRAM 128MB */
+#define CFG_BR3_PRELIM 0xe0001861 /* port size ?bit */
+#define CFG_OR3_PRELIM 0xfc006cc0 /* 128MB local bus SDRAM area (1st half) */
+#define CFG_BR4_PRELIM 0xe4001861 /* port size ?bit */
+#define CFG_OR4_PRELIM 0xfc006cc0 /* 128MB local bus SDRAM area (2nd half) */
+
+/* Disk on Chip (DOC) 128MB */
+#define CFG_BR5_PRELIM 0xe8001001 /* port size ?bit */
+#define CFG_OR5_PRELIM 0xf8006e65 /* 128MB local bus SDRAM area (2nd half) */
+
+/* LCD */
+#define CFG_BR6_PRELIM 0xf4000801 /* port size ?bit */
+#define CFG_OR6_PRELIM 0xfff06e65 /* 128MB local bus SDRAM area (2nd half) */
+
+/* Control logic & misc peripherals */
+#define CFG_BR7_PRELIM 0xf2000801 /* port size ?bit */
+#define CFG_OR7_PRELIM 0xfff06e65 /* 128MB local bus SDRAM area (2nd half) */
+
+#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
+#define CFG_MAX_FLASH_SECT 131 /* sectors per device */
+
+#undef CFG_FLASH_CHECKSUM
+#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+
+#define CFG_FLASH_CFI_DRIVER
+#define CFG_FLASH_CFI
+#define CFG_WRITE_SWAPPED_DATA
+#define CFG_FLASH_EMPTY_INFO
+#define CFG_FLASH_PROTECTION
+
+#undef CONFIG_CLOCKS_IN_MHZ
+
+#define CONFIG_L1_INIT_RAM
+#define CFG_INIT_RAM_LOCK 1
+#ifndef CFG_INIT_RAM_LOCK
+#define CFG_INIT_RAM_ADDR 0x0fd00000 /* Initial RAM address */
+#else
+#define CFG_INIT_RAM_ADDR 0xf8400000 /* Initial RAM address */
+#endif
+#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
+
+#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+
+/* Serial Port */
+#define CONFIG_CONS_INDEX 1
+#undef CONFIG_SERIAL_SOFTWARE_FIFO
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE 1
+#define CFG_NS16550_CLK get_bus_freq(0)
+
+#define CFG_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+
+#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
+#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
+
+/* Use the HUSH parser */
+#define CFG_HUSH_PARSER
+#ifdef CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+/*
+ * Pass open firmware flat tree to kernel
+ */
+#define CONFIG_OF_FLAT_TREE 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+/* maximum size of the flat tree (8K) */
+#define OF_FLAT_TREE_MAX_SIZE 8192
+
+#define OF_CPU "PowerPC,8641@0"
+#define OF_SOC "soc@f8000000"
+#define OF_TBCLK (bd->bi_busfreq / 4)
+#define OF_STDOUT_PATH "/soc@f8000000/serial@4500"
+
+#define CFG_64BIT_VSPRINTF 1
+#define CFG_64BIT_STRTOUL 1
+
+/*
+ * I2C
+ */
+#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C /* I2C with hardware support*/
+#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SLAVE 0x7F
+#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CFG_I2C_OFFSET 0x3100
+
+/*
+ * RapidIO MMU
+ */
+#define CFG_RIO_MEM_BASE 0xc0000000 /* base address */
+#define CFG_RIO_MEM_PHYS CFG_RIO_MEM_BASE
+#define CFG_RIO_MEM_SIZE 0x20000000 /* 128M */
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CFG_PCI1_MEM_BASE 0x80000000
+#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
+#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
+#define CFG_PCI1_IO_BASE 0xe2000000
+#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE
+#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */
+
+/* PCI view of System Memory */
+#define CFG_PCI_MEMORY_BUS 0x00000000
+#define CFG_PCI_MEMORY_PHYS 0x00000000
+#define CFG_PCI_MEMORY_SIZE 0x80000000
+
+#define CFG_PCI2_MEM_BASE 0xa0000000
+#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE
+#define CFG_PCI2_MEM_SIZE 0x10000000 /* 256M */
+#define CFG_PCI2_IO_BASE 0xe3000000
+#define CFG_PCI2_IO_PHYS CFG_PCI2_IO_BASE
+#define CFG_PCI2_IO_SIZE 0x1000000 /* 16M */
+
+#if defined(CONFIG_PCI)
+
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+
+#undef CFG_SCSI_SCAN_BUS_REVERSE
+
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+
+#undef CONFIG_EEPRO100
+#undef CONFIG_TULIP
+
+#if !defined(CONFIG_PCI_PNP)
+ #define PCI_ENET0_IOADDR 0xe0000000
+ #define PCI_ENET0_MEMADDR 0xe0000000
+ #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
+#endif
+
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+
+#define CONFIG_DOS_PARTITION
+#undef CONFIG_SCSI_AHCI
+
+#ifdef CONFIG_SCSI_AHCI
+#define CONFIG_SATA_ULI5288
+#define CFG_SCSI_MAX_SCSI_ID 4
+#define CFG_SCSI_MAX_LUN 1
+#define CFG_SCSI_MAX_DEVICE (CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN)
+#define CFG_SCSI_MAXDEVICE CFG_SCSI_MAX_DEVICE
+#endif
+
+#endif /* CONFIG_PCI */
+
+#if defined(CONFIG_TSEC_ENET)
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI 1
+#endif
+
+/* #define CONFIG_MII 1 */ /* MII PHY management */
+
+#define CONFIG_TSEC1 1
+#define CONFIG_TSEC1_NAME "eTSEC1"
+#define CONFIG_TSEC2 1
+#define CONFIG_TSEC2_NAME "eTSEC2"
+#define CONFIG_TSEC3 1
+#define CONFIG_TSEC3_NAME "eTSEC3"
+#define CONFIG_TSEC4 1
+#define CONFIG_TSEC4_NAME "eTSEC4"
+
+#define TSEC1_PHY_ADDR 0x1F
+#define TSEC2_PHY_ADDR 0x00
+#define TSEC3_PHY_ADDR 0x01
+#define TSEC4_PHY_ADDR 0x02
+#define TSEC1_PHYIDX 0
+#define TSEC2_PHYIDX 0
+#define TSEC3_PHYIDX 0
+#define TSEC4_PHYIDX 0
+
+#define CFG_TBIPA_VALUE 0x1e /* Set TBI address not to conflict with TSEC1_PHY_ADDR */
+
+#define CONFIG_ETHPRIME "eTSEC1"
+
+#endif /* CONFIG_TSEC_ENET */
+
+/*
+ * BAT0 2G Cacheable, non-guarded
+ * 0x0000_0000 2G DDR
+ */
+#define CFG_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CFG_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP)
+#define CFG_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE )
+#define CFG_IBAT0U CFG_DBAT0U
+
+/*
+ * BAT1 1G Cache-inhibited, guarded
+ * 0x8000_0000 512M PCI-Express 1 Memory
+ * 0xa000_0000 512M PCI-Express 2 Memory
+ * Changed it for operating from 0xd0000000
+ */
+#define CFG_DBAT1L ( CFG_PCI1_MEM_BASE | BATL_PP_RW \
+ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT1U (CFG_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_IBAT1L (CFG_PCI1_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT1U CFG_DBAT1U
+
+/*
+ * BAT2 512M Cache-inhibited, guarded
+ * 0xc000_0000 512M RapidIO Memory
+ */
+#define CFG_DBAT2L (CFG_RIO_MEM_BASE | BATL_PP_RW \
+ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT2U (CFG_RIO_MEM_BASE | BATU_BL_512M | BATU_VS | BATU_VP)
+#define CFG_IBAT2L (CFG_RIO_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT2U CFG_DBAT2U
+
+/*
+ * BAT3 4M Cache-inhibited, guarded
+ * 0xf800_0000 4M CCSR
+ */
+#define CFG_DBAT3L ( CFG_CCSRBAR | BATL_PP_RW \
+ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT3U (CFG_CCSRBAR | BATU_BL_4M | BATU_VS | BATU_VP)
+#define CFG_IBAT3L (CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT3U CFG_DBAT3U
+
+/*
+ * BAT4 32M Cache-inhibited, guarded
+ * 0xe200_0000 16M PCI-Express 1 I/O
+ * 0xe300_0000 16M PCI-Express 2 I/0
+ * Note that this is at 0xe0000000
+ */
+#define CFG_DBAT4L ( CFG_PCI1_IO_BASE | BATL_PP_RW \
+ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT4U (CFG_PCI1_IO_BASE | BATU_BL_32M | BATU_VS | BATU_VP)
+#define CFG_IBAT4L (CFG_PCI1_IO_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT4U CFG_DBAT4U
+
+/*
+ * BAT5 128K Cacheable, non-guarded
+ * 0xe401_0000 128K Init RAM for stack in the CPU DCache (no backing memory)
+ */
+#define CFG_DBAT5L (CFG_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CFG_DBAT5U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
+#define CFG_IBAT5L CFG_DBAT5L
+#define CFG_IBAT5U CFG_DBAT5U
+
+/*
+ * BAT6 32M Cache-inhibited, guarded
+ * 0xfe00_0000 32M FLASH
+ */
+#define CFG_DBAT6L ((CFG_FLASH_BASE & 0xfe000000) | BATL_PP_RW \
+ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT6U ((CFG_FLASH_BASE & 0xfe000000) | BATU_BL_32M | BATU_VS | BATU_VP)
+#define CFG_IBAT6L ((CFG_FLASH_BASE & 0xfe000000) | BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CFG_IBAT6U CFG_DBAT6U
+
+#define CFG_DBAT7L 0x00000000
+#define CFG_DBAT7U 0x00000000
+#define CFG_IBAT7L 0x00000000
+#define CFG_IBAT7U 0x00000000
+
+/*
+ * Environment
+ */
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
+#define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
+#define CFG_ENV_SIZE 0x2000
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+#include <config_cmd_default.h>
+ #define CONFIG_CMD_PING
+ #define CONFIG_CMD_I2C
+
+#if defined(CONFIG_PCI)
+ #define CONFIG_CMD_PCI
+#endif
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_LOAD_ADDR 0x2000000 /* default load address */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+ #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+ #define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
+
+/* Cache Configuration */
+#define CFG_DCACHE_SIZE 32768
+#define CFG_CACHELINE_SIZE 32
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
+#endif
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+
+/* The mac addresses for all ethernet interface */
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_ETHADDR 02:E0:0C:00:00:01
+#define CONFIG_ETH1ADDR 02:E0:0C:00:01:FD
+#define CONFIG_ETH2ADDR 02:E0:0C:00:02:FD
+#define CONFIG_ETH3ADDR 02:E0:0C:00:03:FD
+#endif
+
+#define CONFIG_HAS_ETH1 1
+#define CONFIG_HAS_ETH2 1
+#define CONFIG_HAS_ETH3 1
+
+#define CONFIG_IPADDR 192.168.0.50
+
+#define CONFIG_HOSTNAME sbc8641d
+#define CONFIG_ROOTPATH /opt/eldk/ppc_74xx
+#define CONFIG_BOOTFILE uImage
+
+#define CONFIG_SERVERIP 192.168.0.2
+#define CONFIG_GATEWAYIP 192.168.0.1
+#define CONFIG_NETMASK 255.255.255.0
+
+/* default location for tftp and bootm */
+#define CONFIG_LOADADDR 1000000
+
+#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
+#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "consoledev=ttyS0\0" \
+ "ramdiskaddr=2000000\0" \
+ "ramdiskfile=uRamdisk\0" \
+ "dtbaddr=400000\0" \
+ "dtbfile=sbc8641d.dtb\0" \
+ "en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \
+ "dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \
+ "maxcpus=1"
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $dtbaddr $dtbfile;" \
+ "bootm $loadaddr - $dtbaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $dtbaddr $dtbfile;" \
+ "bootm $loadaddr $ramdiskaddr $dtbaddr"
+
+#define CONFIG_FLASHBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "bootm ffd00000 ffb00000 ffa00000"
+
+#define CONFIG_BOOTCOMMAND CONFIG_FLASHBOOTCOMMAND
+
+#endif /* __CONFIG_H */
generated by cgit (git 2.34.1) at 2024-12-29 10:06:36 +0000