diff options
Diffstat (limited to 'README')
| -rw-r--r-- | README | 122 |
1 files changed, 119 insertions, 3 deletions
@@ -815,6 +815,8 @@ The following options need to be configured: CONFIG_CMD_EDITENV edit env variable CONFIG_CMD_EEPROM * EEPROM read/write support CONFIG_CMD_ELF * bootelf, bootvx + CONFIG_CMD_ENV_CALLBACK * display details about env callbacks + CONFIG_CMD_ENV_FLAGS * display details about env flags CONFIG_CMD_EXPORTENV * export the environment CONFIG_CMD_EXT2 * ext2 command support CONFIG_CMD_EXT4 * ext4 command support @@ -824,8 +826,10 @@ The following options need to be configured: CONFIG_CMD_FDOS * Dos diskette Support CONFIG_CMD_FLASH flinfo, erase, protect CONFIG_CMD_FPGA FPGA device initialization support + CONFIG_CMD_GETTIME * Get time since boot CONFIG_CMD_GO * the 'go' command (exec code) CONFIG_CMD_GREPENV * search environment + CONFIG_CMD_HASH * calculate hash / digest CONFIG_CMD_HWFLOW * RTS/CTS hw flow control CONFIG_CMD_I2C * I2C serial bus support CONFIG_CMD_IDE * IDE harddisk support @@ -860,6 +864,7 @@ The following options need to be configured: CONFIG_CMD_PING * send ICMP ECHO_REQUEST to network host CONFIG_CMD_PORTIO * Port I/O + CONFIG_CMD_READ * Read raw data from partition CONFIG_CMD_REGINFO * Register dump CONFIG_CMD_RUN run command in env variable CONFIG_CMD_SAVES * save S record dump @@ -1481,10 +1486,29 @@ CBFS (Coreboot Filesystem) support Normally display is black on white background; define CONFIG_SYS_WHITE_ON_BLACK to get it inverted. + CONFIG_LCD_ALIGNMENT + + Normally the LCD is page-aligned (tyically 4KB). If this is + defined then the LCD will be aligned to this value instead. + For ARM it is sometimes useful to use MMU_SECTION_SIZE + here, since it is cheaper to change data cache settings on + a per-section basis. + + CONFIG_CONSOLE_SCROLL_LINES + + When the console need to be scrolled, this is the number of + lines to scroll by. It defaults to 1. Increasing this makes + the console jump but can help speed up operation when scrolling + is slow. + CONFIG_LCD_BMP_RLE8 Support drawing of RLE8-compressed bitmaps on the LCD. + CONFIG_I2C_EDID + + Enables an 'i2c edid' command which can read EDID + information over I2C from an attached LCD display. - Splash Screen Support: CONFIG_SPLASH_SCREEN @@ -2179,6 +2203,11 @@ CBFS (Coreboot Filesystem) support serial# is unaffected by this, i. e. it remains read-only.] + The same can be accomplished in a more flexible way + for any variable by configuring the type of access + to allow for those variables in the ".flags" variable + or define CONFIG_ENV_FLAGS_LIST_STATIC. + - Protected RAM: CONFIG_PRAM @@ -2409,6 +2438,23 @@ CBFS (Coreboot Filesystem) support A better solution is to properly configure the firewall, but sometimes that is not allowed. +- Hashing support: + CONFIG_CMD_HASH + + This enables a generic 'hash' command which can produce + hashes / digests from a few algorithms (e.g. SHA1, SHA256). + + CONFIG_HASH_VERIFY + + Enable the hash verify command (hash -v). This adds to code + size a little. + + CONFIG_SHA1 - support SHA1 hashing + CONFIG_SHA256 - support SHA256 hashing + + Note: There is also a sha1sum command, which should perhaps + be deprecated in favour of 'hash sha1'. + - Show boot progress: CONFIG_SHOW_BOOT_PROGRESS @@ -2943,9 +2989,6 @@ Configuration Settings: non page size aligned address and this could cause major problems. -- CONFIG_SYS_TFTP_LOADADDR: - Default load address for network file downloads - - CONFIG_SYS_LOADS_BAUD_CHANGE: Enable temporary baudrate change while serial download @@ -3087,6 +3130,49 @@ Configuration Settings: cases. This setting can be used to tune behaviour; see lib/hashtable.c for details. +- CONFIG_ENV_FLAGS_LIST_DEFAULT +- CONFIG_ENV_FLAGS_LIST_STATIC + Enable validation of the values given to enviroment variables when + calling env set. Variables can be restricted to only decimal, + hexadecimal, or boolean. If CONFIG_CMD_NET is also defined, + the variables can also be restricted to IP address or MAC address. + + The format of the list is: + type_attribute = [s|d|x|b|i|m] + access_atribute = [a|r|o|c] + attributes = type_attribute[access_atribute] + entry = variable_name[:attributes] + list = entry[,list] + + The type attributes are: + s - String (default) + d - Decimal + x - Hexadecimal + b - Boolean ([1yYtT|0nNfF]) + i - IP address + m - MAC address + + The access attributes are: + a - Any (default) + r - Read-only + o - Write-once + c - Change-default + + - CONFIG_ENV_FLAGS_LIST_DEFAULT + Define this to a list (string) to define the ".flags" + envirnoment variable in the default or embedded environment. + + - CONFIG_ENV_FLAGS_LIST_STATIC + Define this to a list (string) to define validation that + should be done if an entry is not found in the ".flags" + environment variable. To override a setting in the static + list, simply add an entry for the same variable name to the + ".flags" variable. + +- CONFIG_ENV_ACCESS_IGNORE_FORCE + If defined, don't allow the -f switch to env set override variable + access flags. + The following definitions that deal with the placement and management of environment data (variable area); in general, we support the following configurations: @@ -4188,6 +4274,36 @@ Please note that changes to some configuration parameters may take only effect after the next boot (yes, that's just like Windoze :-). +Callback functions for environment variables: +--------------------------------------------- + +For some environment variables, the behavior of u-boot needs to change +when their values are changed. This functionailty allows functions to +be associated with arbitrary variables. On creation, overwrite, or +deletion, the callback will provide the opportunity for some side +effect to happen or for the change to be rejected. + +The callbacks are named and associated with a function using the +U_BOOT_ENV_CALLBACK macro in your board or driver code. + +These callbacks are associated with variables in one of two ways. The +static list can be added to by defining CONFIG_ENV_CALLBACK_LIST_STATIC +in the board configuration to a string that defines a list of +associations. The list must be in the following format: + + entry = variable_name[:callback_name] + list = entry[,list] + +If the callback name is not specified, then the callback is deleted. +Spaces are also allowed anywhere in the list. + +Callbacks can also be associated by defining the ".callbacks" variable +with the same list format above. Any association in ".callbacks" will +override any association in the static list. You can define +CONFIG_ENV_CALLBACK_LIST_DEFAULT to a list (string) to define the +".callbacks" envirnoment variable in the default or embedded environment. + + Command Line Parsing: ===================== |