diff options
Diffstat (limited to 'README')
| -rw-r--r-- | README | 49 |
1 files changed, 47 insertions, 2 deletions
@@ -843,6 +843,7 @@ The following options need to be configured: CONFIG_CMD_FDOS * Dos diskette Support CONFIG_CMD_FLASH flinfo, erase, protect CONFIG_CMD_FPGA FPGA device initialization support + CONFIG_CMD_FUSE Device fuse support CONFIG_CMD_GETTIME * Get time since boot CONFIG_CMD_GO * the 'go' command (exec code) CONFIG_CMD_GREPENV * search environment @@ -1208,7 +1209,23 @@ The following options need to be configured: If this option is set, the driver enables cache flush. - TPM Support: - CONFIG_GENERIC_LPC_TPM + CONFIG_TPM + Support TPM devices. + + CONFIG_TPM_TIS_I2C + Support for i2c bus TPM devices. Only one device + per system is supported at this time. + + CONFIG_TPM_TIS_I2C_BUS_NUMBER + Define the the i2c bus number for the TPM device + + CONFIG_TPM_TIS_I2C_SLAVE_ADDRESS + Define the TPM's address on the i2c bus + + CONFIG_TPM_TIS_I2C_BURST_LIMITATION + Define the burst count bytes upper limit + + CONFIG_TPM_TIS_LPC Support for generic parallel port TPM devices. Only one device per system is supported at this time. @@ -1244,6 +1261,9 @@ The following options need to be configured: CONFIG_USB_EHCI_TXFIFO_THRESH enables setting of the txfilltuning field in the EHCI controller on reset. + CONFIG_USB_HUB_MIN_POWER_ON_DELAY defines the minimum + interval for usb hub power-on delay.(minimum 100msec) + - USB Device: Define the below if you wish to use the USB console. Once firmware is rebuilt from a serial console issue the @@ -2915,12 +2935,30 @@ FIT uImage format: Address, size and partition on the MMC to load U-Boot from when the MMC is being used in raw mode. + CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR + Sector to load kernel uImage from when MMC is being + used in raw mode (for Falcon mode) + + CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR, + CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS + Sector and number of sectors to load kernel argument + parameters from when MMC is being used in raw mode + (for falcon mode) + CONFIG_SPL_FAT_SUPPORT Support for fs/fat/libfat.o in SPL binary CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME Filename to read to load U-Boot when reading from FAT + CONFIG_SPL_FAT_LOAD_KERNEL_NAME + Filename to read to load kernel uImage when reading + from FAT (for Falcon mode) + + CONFIG_SPL_FAT_LOAD_ARGS_NAME + Filename to read to load kernel argument parameters + when reading from FAT (for Falcon mode) + CONFIG_SPL_MPC83XX_WAIT_FOR_NAND Set this for NAND SPL on PPC mpc83xx targets, so that start.S waits for the rest of the SPL to load before @@ -3345,6 +3383,10 @@ Configuration Settings: offset _bss_start_ofs from CONFIG_SYS_TEXT_BASE, rather than directly. You should not need to touch this setting. +- CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC (OMAP only) + This is set by OMAP boards for the max time that reset should + be asserted. See doc/README.omap-reset-time for details on how + the value can be calulated on a given board. The following definitions that deal with the placement and management of environment data (variable area); in general, we support the @@ -3859,6 +3901,9 @@ Low Level (hardware related) configuration options: a second time. Useful for platforms that are pre-booted by coreboot or similar. +- CONFIG_PCI_INDIRECT_BRIDGE: + Enable support for indirect PCI bridges. + - CONFIG_SYS_SRIO: Chip has SRIO or not @@ -5063,7 +5108,7 @@ On some platforms, it's possible to boot Linux zImage. This is done using the "bootz" command. The syntax of "bootz" command is the same as the syntax of "bootm" command. -Note, defining the CONFIG_SUPPORT_INITRD_RAW allows user to supply +Note, defining the CONFIG_SUPPORT_RAW_INITRD allows user to supply kernel with raw initrd images. The syntax is slightly different, the address of the initrd must be augmented by it's size, in the following format: "<initrd addres>:<initrd size>". |