diff options
Diffstat (limited to 'arch/arm/cpu/armv7/am33xx/clock_am33xx.c')
| -rw-r--r-- | arch/arm/cpu/armv7/am33xx/clock_am33xx.c | 495 |
1 files changed, 116 insertions, 379 deletions
diff --git a/arch/arm/cpu/armv7/am33xx/clock_am33xx.c b/arch/arm/cpu/armv7/am33xx/clock_am33xx.c index fb3fb43dcc..e5f287b338 100644 --- a/arch/arm/cpu/armv7/am33xx/clock_am33xx.c +++ b/arch/arm/cpu/armv7/am33xx/clock_am33xx.c @@ -14,392 +14,129 @@ #include <asm/arch/hardware.h> #include <asm/io.h> -#define PRCM_MOD_EN 0x2 -#define PRCM_FORCE_WAKEUP 0x2 -#define PRCM_FUNCTL 0x0 - -#define PRCM_EMIF_CLK_ACTIVITY BIT(2) -#define PRCM_L3_GCLK_ACTIVITY BIT(4) - -#define PLL_BYPASS_MODE 0x4 -#define ST_MN_BYPASS 0x00000100 -#define ST_DPLL_CLK 0x00000001 -#define CLK_SEL_MASK 0x7ffff -#define CLK_DIV_MASK 0x1f -#define CLK_DIV2_MASK 0x7f -#define CLK_SEL_SHIFT 0x8 -#define CLK_MODE_SEL 0x7 -#define CLK_MODE_MASK 0xfffffff8 -#define CLK_DIV_SEL 0xFFFFFFE0 -#define CPGMAC0_IDLE 0x30000 -#define DPLL_CLKDCOLDO_GATE_CTRL 0x300 - #define OSC (V_OSCK/1000000) -#define MPUPLL_M CONFIG_SYS_MPUCLK -#define MPUPLL_N (OSC-1) -#define MPUPLL_M2 1 - -/* Core PLL Fdll = 1 GHZ, */ -#define COREPLL_M 1000 -#define COREPLL_N (OSC-1) - -#define COREPLL_M4 10 /* CORE_CLKOUTM4 = 200 MHZ */ -#define COREPLL_M5 8 /* CORE_CLKOUTM5 = 250 MHZ */ -#define COREPLL_M6 4 /* CORE_CLKOUTM6 = 500 MHZ */ - -/* - * USB PHY clock is 960 MHZ. Since, this comes directly from Fdll, Fdll - * frequency needs to be set to 960 MHZ. Hence, - * For clkout = 192 MHZ, Fdll = 960 MHZ, divider values are given below - */ -#define PERPLL_M 960 -#define PERPLL_N (OSC-1) -#define PERPLL_M2 5 - -/* DDR Freq is 266 MHZ for now */ -/* Set Fdll = 400 MHZ , Fdll = M * 2 * CLKINP/ N + 1; clkout = Fdll /(2 * M2) */ -#define DDRPLL_M 266 -#define DDRPLL_N (OSC-1) -#define DDRPLL_M2 1 - -const struct cm_perpll *cmper = (struct cm_perpll *)CM_PER; -const struct cm_wkuppll *cmwkup = (struct cm_wkuppll *)CM_WKUP; -const struct cm_dpll *cmdpll = (struct cm_dpll *)CM_DPLL; -const struct cm_rtc *cmrtc = (struct cm_rtc *)CM_RTC; - -static void enable_interface_clocks(void) +struct cm_perpll *const cmper = (struct cm_perpll *)CM_PER; +struct cm_wkuppll *const cmwkup = (struct cm_wkuppll *)CM_WKUP; +struct cm_dpll *const cmdpll = (struct cm_dpll *)CM_DPLL; +struct cm_rtc *const cmrtc = (struct cm_rtc *)CM_RTC; + +const struct dpll_regs dpll_mpu_regs = { + .cm_clkmode_dpll = CM_WKUP + 0x88, + .cm_idlest_dpll = CM_WKUP + 0x20, + .cm_clksel_dpll = CM_WKUP + 0x2C, + .cm_div_m2_dpll = CM_WKUP + 0xA8, +}; + +const struct dpll_regs dpll_core_regs = { + .cm_clkmode_dpll = CM_WKUP + 0x90, + .cm_idlest_dpll = CM_WKUP + 0x5C, + .cm_clksel_dpll = CM_WKUP + 0x68, + .cm_div_m4_dpll = CM_WKUP + 0x80, + .cm_div_m5_dpll = CM_WKUP + 0x84, + .cm_div_m6_dpll = CM_WKUP + 0xD8, +}; + +const struct dpll_regs dpll_per_regs = { + .cm_clkmode_dpll = CM_WKUP + 0x8C, + .cm_idlest_dpll = CM_WKUP + 0x70, + .cm_clksel_dpll = CM_WKUP + 0x9C, + .cm_div_m2_dpll = CM_WKUP + 0xAC, +}; + +const struct dpll_regs dpll_ddr_regs = { + .cm_clkmode_dpll = CM_WKUP + 0x94, + .cm_idlest_dpll = CM_WKUP + 0x34, + .cm_clksel_dpll = CM_WKUP + 0x40, + .cm_div_m2_dpll = CM_WKUP + 0xA0, +}; + +const struct dpll_params dpll_mpu = { + CONFIG_SYS_MPUCLK, OSC-1, 1, -1, -1, -1, -1}; +const struct dpll_params dpll_core = { + 1000, OSC-1, -1, -1, 10, 8, 4}; +const struct dpll_params dpll_per = { + 960, OSC-1, 5, -1, -1, -1, -1}; + +void setup_clocks_for_console(void) { - /* Enable all the Interconnect Modules */ - writel(PRCM_MOD_EN, &cmper->l3clkctrl); - while (readl(&cmper->l3clkctrl) != PRCM_MOD_EN) - ; - - writel(PRCM_MOD_EN, &cmper->l4lsclkctrl); - while (readl(&cmper->l4lsclkctrl) != PRCM_MOD_EN) - ; - - writel(PRCM_MOD_EN, &cmper->l4fwclkctrl); - while (readl(&cmper->l4fwclkctrl) != PRCM_MOD_EN) - ; - - writel(PRCM_MOD_EN, &cmwkup->wkl4wkclkctrl); - while (readl(&cmwkup->wkl4wkclkctrl) != PRCM_MOD_EN) - ; - - writel(PRCM_MOD_EN, &cmper->l3instrclkctrl); - while (readl(&cmper->l3instrclkctrl) != PRCM_MOD_EN) - ; - - writel(PRCM_MOD_EN, &cmper->l4hsclkctrl); - while (readl(&cmper->l4hsclkctrl) != PRCM_MOD_EN) - ; - - writel(PRCM_MOD_EN, &cmwkup->wkgpio0clkctrl); - while (readl(&cmwkup->wkgpio0clkctrl) != PRCM_MOD_EN) - ; -} - -/* - * Force power domain wake up transition - * Ensure that the corresponding interface clock is active before - * using the peripheral - */ -static void power_domain_wkup_transition(void) -{ - writel(PRCM_FORCE_WAKEUP, &cmper->l3clkstctrl); - writel(PRCM_FORCE_WAKEUP, &cmper->l4lsclkstctrl); - writel(PRCM_FORCE_WAKEUP, &cmwkup->wkclkstctrl); - writel(PRCM_FORCE_WAKEUP, &cmper->l4fwclkstctrl); - writel(PRCM_FORCE_WAKEUP, &cmper->l3sclkstctrl); + clrsetbits_le32(&cmwkup->wkclkstctrl, CD_CLKCTRL_CLKTRCTRL_MASK, + CD_CLKCTRL_CLKTRCTRL_SW_WKUP << + CD_CLKCTRL_CLKTRCTRL_SHIFT); + + clrsetbits_le32(&cmper->l4hsclkstctrl, CD_CLKCTRL_CLKTRCTRL_MASK, + CD_CLKCTRL_CLKTRCTRL_SW_WKUP << + CD_CLKCTRL_CLKTRCTRL_SHIFT); + + clrsetbits_le32(&cmwkup->wkup_uart0ctrl, + MODULE_CLKCTRL_MODULEMODE_MASK, + MODULE_CLKCTRL_MODULEMODE_SW_EXPLICIT_EN << + MODULE_CLKCTRL_MODULEMODE_SHIFT); + clrsetbits_le32(&cmper->uart1clkctrl, + MODULE_CLKCTRL_MODULEMODE_MASK, + MODULE_CLKCTRL_MODULEMODE_SW_EXPLICIT_EN << + MODULE_CLKCTRL_MODULEMODE_SHIFT); + clrsetbits_le32(&cmper->uart2clkctrl, + MODULE_CLKCTRL_MODULEMODE_MASK, + MODULE_CLKCTRL_MODULEMODE_SW_EXPLICIT_EN << + MODULE_CLKCTRL_MODULEMODE_SHIFT); + clrsetbits_le32(&cmper->uart3clkctrl, + MODULE_CLKCTRL_MODULEMODE_MASK, + MODULE_CLKCTRL_MODULEMODE_SW_EXPLICIT_EN << + MODULE_CLKCTRL_MODULEMODE_SHIFT); + clrsetbits_le32(&cmper->uart4clkctrl, + MODULE_CLKCTRL_MODULEMODE_MASK, + MODULE_CLKCTRL_MODULEMODE_SW_EXPLICIT_EN << + MODULE_CLKCTRL_MODULEMODE_SHIFT); + clrsetbits_le32(&cmper->uart5clkctrl, + MODULE_CLKCTRL_MODULEMODE_MASK, + MODULE_CLKCTRL_MODULEMODE_SW_EXPLICIT_EN << + MODULE_CLKCTRL_MODULEMODE_SHIFT); } -/* - * Enable the peripheral clock for required peripherals - */ -static void enable_per_clocks(void) +void enable_basic_clocks(void) { - /* Enable the control module though RBL would have done it*/ - writel(PRCM_MOD_EN, &cmwkup->wkctrlclkctrl); - while (readl(&cmwkup->wkctrlclkctrl) != PRCM_MOD_EN) - ; - - /* Enable the module clock */ - writel(PRCM_MOD_EN, &cmper->timer2clkctrl); - while (readl(&cmper->timer2clkctrl) != PRCM_MOD_EN) - ; + u32 *const clk_domains[] = { + &cmper->l3clkstctrl, + &cmper->l4fwclkstctrl, + &cmper->l3sclkstctrl, + &cmper->l4lsclkstctrl, + &cmwkup->wkclkstctrl, + &cmper->emiffwclkctrl, + &cmrtc->clkstctrl, + 0 + }; + + u32 *const clk_modules_explicit_en[] = { + &cmper->l3clkctrl, + &cmper->l4lsclkctrl, + &cmper->l4fwclkctrl, + &cmwkup->wkl4wkclkctrl, + &cmper->l3instrclkctrl, + &cmper->l4hsclkctrl, + &cmwkup->wkgpio0clkctrl, + &cmwkup->wkctrlclkctrl, + &cmper->timer2clkctrl, + &cmper->gpmcclkctrl, + &cmper->elmclkctrl, + &cmper->mmc0clkctrl, + &cmper->mmc1clkctrl, + &cmwkup->wkup_i2c0ctrl, + &cmper->gpio1clkctrl, + &cmper->gpio2clkctrl, + &cmper->gpio3clkctrl, + &cmper->i2c1clkctrl, + &cmper->cpgmac0clkctrl, + &cmper->spi0clkctrl, + &cmrtc->rtcclkctrl, + &cmper->usb0clkctrl, + &cmper->emiffwclkctrl, + &cmper->emifclkctrl, + 0 + }; + + do_enable_clocks(clk_domains, clk_modules_explicit_en, 1); /* Select the Master osc 24 MHZ as Timer2 clock source */ writel(0x1, &cmdpll->clktimer2clk); - - /* UART0 */ - writel(PRCM_MOD_EN, &cmwkup->wkup_uart0ctrl); - while (readl(&cmwkup->wkup_uart0ctrl) != PRCM_MOD_EN) - ; - - /* UART1 */ -#ifdef CONFIG_SERIAL2 - writel(PRCM_MOD_EN, &cmper->uart1clkctrl); - while (readl(&cmper->uart1clkctrl) != PRCM_MOD_EN) - ; -#endif /* CONFIG_SERIAL2 */ - - /* UART2 */ -#ifdef CONFIG_SERIAL3 - writel(PRCM_MOD_EN, &cmper->uart2clkctrl); - while (readl(&cmper->uart2clkctrl) != PRCM_MOD_EN) - ; -#endif /* CONFIG_SERIAL3 */ - - /* UART3 */ -#ifdef CONFIG_SERIAL4 - writel(PRCM_MOD_EN, &cmper->uart3clkctrl); - while (readl(&cmper->uart3clkctrl) != PRCM_MOD_EN) - ; -#endif /* CONFIG_SERIAL4 */ - - /* UART4 */ -#ifdef CONFIG_SERIAL5 - writel(PRCM_MOD_EN, &cmper->uart4clkctrl); - while (readl(&cmper->uart4clkctrl) != PRCM_MOD_EN) - ; -#endif /* CONFIG_SERIAL5 */ - - /* UART5 */ -#ifdef CONFIG_SERIAL6 - writel(PRCM_MOD_EN, &cmper->uart5clkctrl); - while (readl(&cmper->uart5clkctrl) != PRCM_MOD_EN) - ; -#endif /* CONFIG_SERIAL6 */ - - /* GPMC */ - writel(PRCM_MOD_EN, &cmper->gpmcclkctrl); - while (readl(&cmper->gpmcclkctrl) != PRCM_MOD_EN) - ; - - /* ELM */ - writel(PRCM_MOD_EN, &cmper->elmclkctrl); - while (readl(&cmper->elmclkctrl) != PRCM_MOD_EN) - ; - - /* MMC0*/ - writel(PRCM_MOD_EN, &cmper->mmc0clkctrl); - while (readl(&cmper->mmc0clkctrl) != PRCM_MOD_EN) - ; - - /* MMC1 */ - writel(PRCM_MOD_EN, &cmper->mmc1clkctrl); - while (readl(&cmper->mmc1clkctrl) != PRCM_MOD_EN) - ; - - /* i2c0 */ - writel(PRCM_MOD_EN, &cmwkup->wkup_i2c0ctrl); - while (readl(&cmwkup->wkup_i2c0ctrl) != PRCM_MOD_EN) - ; - - /* gpio1 module */ - writel(PRCM_MOD_EN, &cmper->gpio1clkctrl); - while (readl(&cmper->gpio1clkctrl) != PRCM_MOD_EN) - ; - - /* gpio2 module */ - writel(PRCM_MOD_EN, &cmper->gpio2clkctrl); - while (readl(&cmper->gpio2clkctrl) != PRCM_MOD_EN) - ; - - /* gpio3 module */ - writel(PRCM_MOD_EN, &cmper->gpio3clkctrl); - while (readl(&cmper->gpio3clkctrl) != PRCM_MOD_EN) - ; - - /* i2c1 */ - writel(PRCM_MOD_EN, &cmper->i2c1clkctrl); - while (readl(&cmper->i2c1clkctrl) != PRCM_MOD_EN) - ; - - /* Ethernet */ - writel(PRCM_MOD_EN, &cmper->cpgmac0clkctrl); - while ((readl(&cmper->cpgmac0clkctrl) & CPGMAC0_IDLE) != PRCM_FUNCTL) - ; - - /* spi0 */ - writel(PRCM_MOD_EN, &cmper->spi0clkctrl); - while (readl(&cmper->spi0clkctrl) != PRCM_MOD_EN) - ; - - /* RTC */ - writel(PRCM_MOD_EN, &cmrtc->rtcclkctrl); - while (readl(&cmrtc->rtcclkctrl) != PRCM_MOD_EN) - ; - - /* MUSB */ - writel(PRCM_MOD_EN, &cmper->usb0clkctrl); - while (readl(&cmper->usb0clkctrl) != PRCM_MOD_EN) - ; -} - -void mpu_pll_config_val(int mpull_m) -{ - u32 clkmode, clksel, div_m2; - - clkmode = readl(&cmwkup->clkmoddpllmpu); - clksel = readl(&cmwkup->clkseldpllmpu); - div_m2 = readl(&cmwkup->divm2dpllmpu); - - /* Set the PLL to bypass Mode */ - writel(PLL_BYPASS_MODE, &cmwkup->clkmoddpllmpu); - while (readl(&cmwkup->idlestdpllmpu) != ST_MN_BYPASS) - ; - - clksel = clksel & (~CLK_SEL_MASK); - clksel = clksel | ((mpull_m << CLK_SEL_SHIFT) | MPUPLL_N); - writel(clksel, &cmwkup->clkseldpllmpu); - - div_m2 = div_m2 & ~CLK_DIV_MASK; - div_m2 = div_m2 | MPUPLL_M2; - writel(div_m2, &cmwkup->divm2dpllmpu); - - clkmode = clkmode | CLK_MODE_SEL; - writel(clkmode, &cmwkup->clkmoddpllmpu); - - while (readl(&cmwkup->idlestdpllmpu) != ST_DPLL_CLK) - ; -} - -static void mpu_pll_config(void) -{ - mpu_pll_config_val(CONFIG_SYS_MPUCLK); -} - -static void core_pll_config(void) -{ - u32 clkmode, clksel, div_m4, div_m5, div_m6; - - clkmode = readl(&cmwkup->clkmoddpllcore); - clksel = readl(&cmwkup->clkseldpllcore); - div_m4 = readl(&cmwkup->divm4dpllcore); - div_m5 = readl(&cmwkup->divm5dpllcore); - div_m6 = readl(&cmwkup->divm6dpllcore); - - /* Set the PLL to bypass Mode */ - writel(PLL_BYPASS_MODE, &cmwkup->clkmoddpllcore); - - while (readl(&cmwkup->idlestdpllcore) != ST_MN_BYPASS) - ; - - clksel = clksel & (~CLK_SEL_MASK); - clksel = clksel | ((COREPLL_M << CLK_SEL_SHIFT) | COREPLL_N); - writel(clksel, &cmwkup->clkseldpllcore); - - div_m4 = div_m4 & ~CLK_DIV_MASK; - div_m4 = div_m4 | COREPLL_M4; - writel(div_m4, &cmwkup->divm4dpllcore); - - div_m5 = div_m5 & ~CLK_DIV_MASK; - div_m5 = div_m5 | COREPLL_M5; - writel(div_m5, &cmwkup->divm5dpllcore); - - div_m6 = div_m6 & ~CLK_DIV_MASK; - div_m6 = div_m6 | COREPLL_M6; - writel(div_m6, &cmwkup->divm6dpllcore); - - clkmode = clkmode | CLK_MODE_SEL; - writel(clkmode, &cmwkup->clkmoddpllcore); - - while (readl(&cmwkup->idlestdpllcore) != ST_DPLL_CLK) - ; -} - -static void per_pll_config(void) -{ - u32 clkmode, clksel, div_m2; - - clkmode = readl(&cmwkup->clkmoddpllper); - clksel = readl(&cmwkup->clkseldpllper); - div_m2 = readl(&cmwkup->divm2dpllper); - - /* Set the PLL to bypass Mode */ - writel(PLL_BYPASS_MODE, &cmwkup->clkmoddpllper); - - while (readl(&cmwkup->idlestdpllper) != ST_MN_BYPASS) - ; - - clksel = clksel & (~CLK_SEL_MASK); - clksel = clksel | ((PERPLL_M << CLK_SEL_SHIFT) | PERPLL_N); - writel(clksel, &cmwkup->clkseldpllper); - - div_m2 = div_m2 & ~CLK_DIV2_MASK; - div_m2 = div_m2 | PERPLL_M2; - writel(div_m2, &cmwkup->divm2dpllper); - - clkmode = clkmode | CLK_MODE_SEL; - writel(clkmode, &cmwkup->clkmoddpllper); - - while (readl(&cmwkup->idlestdpllper) != ST_DPLL_CLK) - ; - - writel(DPLL_CLKDCOLDO_GATE_CTRL, &cmwkup->clkdcoldodpllper); -} - -void ddr_pll_config(unsigned int ddrpll_m) -{ - u32 clkmode, clksel, div_m2; - - clkmode = readl(&cmwkup->clkmoddpllddr); - clksel = readl(&cmwkup->clkseldpllddr); - div_m2 = readl(&cmwkup->divm2dpllddr); - - /* Set the PLL to bypass Mode */ - clkmode = (clkmode & CLK_MODE_MASK) | PLL_BYPASS_MODE; - writel(clkmode, &cmwkup->clkmoddpllddr); - - /* Wait till bypass mode is enabled */ - while ((readl(&cmwkup->idlestdpllddr) & ST_MN_BYPASS) - != ST_MN_BYPASS) - ; - - clksel = clksel & (~CLK_SEL_MASK); - clksel = clksel | ((ddrpll_m << CLK_SEL_SHIFT) | DDRPLL_N); - writel(clksel, &cmwkup->clkseldpllddr); - - div_m2 = div_m2 & CLK_DIV_SEL; - div_m2 = div_m2 | DDRPLL_M2; - writel(div_m2, &cmwkup->divm2dpllddr); - - clkmode = (clkmode & CLK_MODE_MASK) | CLK_MODE_SEL; - writel(clkmode, &cmwkup->clkmoddpllddr); - - /* Wait till dpll is locked */ - while ((readl(&cmwkup->idlestdpllddr) & ST_DPLL_CLK) != ST_DPLL_CLK) - ; -} - -void enable_emif_clocks(void) -{ - /* Enable the EMIF_FW Functional clock */ - writel(PRCM_MOD_EN, &cmper->emiffwclkctrl); - /* Enable EMIF0 Clock */ - writel(PRCM_MOD_EN, &cmper->emifclkctrl); - /* Poll if module is functional */ - while ((readl(&cmper->emifclkctrl)) != PRCM_MOD_EN) - ; -} - -/* - * Configure the PLL/PRCM for necessary peripherals - */ -void pll_init() -{ - mpu_pll_config(); - core_pll_config(); - per_pll_config(); - - /* Enable the required interconnect clocks */ - enable_interface_clocks(); - - /* Power domain wake up transition */ - power_domain_wkup_transition(); - - /* Enable the required peripherals */ - enable_per_clocks(); } |