diff options
Diffstat (limited to 'arch/arm/cpu/armv8/fsl-layerscape')
| -rw-r--r-- | arch/arm/cpu/armv8/fsl-layerscape/cpu.c | 12 | ||||
| -rw-r--r-- | arch/arm/cpu/armv8/fsl-layerscape/doc/README.lsch3 | 29 |
2 files changed, 41 insertions, 0 deletions
diff --git a/arch/arm/cpu/armv8/fsl-layerscape/cpu.c b/arch/arm/cpu/armv8/fsl-layerscape/cpu.c index 9a5a6b53f7..297687d3c6 100644 --- a/arch/arm/cpu/armv8/fsl-layerscape/cpu.c +++ b/arch/arm/cpu/armv8/fsl-layerscape/cpu.c @@ -636,6 +636,9 @@ int timer_init(void) #ifdef CONFIG_FSL_LSCH3 u32 __iomem *cltbenr = (u32 *)CONFIG_SYS_FSL_PMU_CLTBENR; #endif +#ifdef CONFIG_LS2080A + u32 __iomem *pctbenr = (u32 *)FSL_PMU_PCTBENR_OFFSET; +#endif #ifdef COUNTER_FREQUENCY_REAL unsigned long cntfrq = COUNTER_FREQUENCY_REAL; @@ -650,6 +653,15 @@ int timer_init(void) out_le32(cltbenr, 0xf); #endif +#ifdef CONFIG_LS2080A + /* + * In certain Layerscape SoCs, the clock for each core's + * has an enable bit in the PMU Physical Core Time Base Enable + * Register (PCTBENR), which allows the watchdog to operate. + */ + setbits_le32(pctbenr, 0xff); +#endif + /* Enable clock for timer * This is a global setting. */ diff --git a/arch/arm/cpu/armv8/fsl-layerscape/doc/README.lsch3 b/arch/arm/cpu/armv8/fsl-layerscape/doc/README.lsch3 index f9323c1d28..da5e052569 100644 --- a/arch/arm/cpu/armv8/fsl-layerscape/doc/README.lsch3 +++ b/arch/arm/cpu/armv8/fsl-layerscape/doc/README.lsch3 @@ -121,6 +121,35 @@ mcboottimeout: MC boot timeout in milliseconds. If this variable is not defined mcmemsize: MC DRAM block size. If this variable is not defined, the value CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE will be assumed. +mcinitcmd: This environment variable is defined to initiate MC and DPL deployment + from the location where it is stored(NOR, NAND, SD, SATA, USB)during + u-boot booting.If this variable is not defined then MC_BOOT_ENV_VAR + will be null and MC will not be booted and DPL will not be applied + during U-boot booting.However the MC, DPC and DPL can be applied from + console independently. + The variable needs to be set from the console once and then on + rebooting the parameters set in the varible will automatically be + executed. The commmand is demostrated taking an example of mc boot + using NOR Flash i.e. MC, DPL, and DPC is stored in the NOR flash: + + cp.b 0xa0000000 0x580300000 $filesize + cp.b 0x80000000 0x580800000 $filesize + cp.b 0x90000000 0x580700000 $filesize + + setenv mcinitcmd 'fsl_mc start mc 0x580300000 0x580800000' + + If only linux is to be booted then the mcinitcmd environment should be set as + + setenv mcinitcmd 'fsl_mc start mc 0x580300000 0x580800000;fsl_mc apply DPL 0x580700000' + + Here the addresses 0xa0000000, 0x80000000, 0x80000000 are of DDR to where + MC binary, DPC binary and DPL binary are stored and 0x580300000, 0x580800000 + and 0x580700000 are addresses in NOR where these are copied. It is to be + noted that these addresses in 'fsl_mc start mc 0x580300000 0x580800000;fsl_mc apply DPL 0x580700000' + can be replaced with the addresses of DDR to + which these will be copied in case of these binaries being stored in other + devices like SATA, USB, NAND, SD etc. + Booting from NAND ------------------- Booting from NAND requires two images, RCW and u-boot-with-spl.bin. |