1 files changed, 0 insertions, 156 deletions
diff --git a/arch/arm/cpu/armv8/zynqmp/Kconfig b/arch/arm/cpu/armv8/zynqmp/Kconfig
deleted file mode 100644
index 8a311e1c89..0000000000
--- a/arch/arm/cpu/armv8/zynqmp/Kconfig
+++ /dev/null
@@ -1,156 +0,0 @@
-if ARCH_ZYNQMP
-
-config SPL_FAT_SUPPORT
-	default y
-
-config SPL_LIBCOMMON_SUPPORT
-	default y
-
-config SPL_LIBDISK_SUPPORT
-	default y
-
-config SPL_LIBGENERIC_SUPPORT
-	default y
-
-config SPL_MMC_SUPPORT
-	default y if MMC_SDHCI_ZYNQ
-
-config SPL_SERIAL_SUPPORT
-	default y
-
-config SPL_SPI_FLASH_SUPPORT
-	default y if ZYNQ_QSPI
-
-config SPL_SPI_SUPPORT
-	default y if ZYNQ_QSPI
-
-config SYS_BOARD
-	default "zynqmp"
-
-config SYS_VENDOR
-	string "Vendor name"
-	default "xilinx"
-
-config SYS_SOC
-	default "zynqmp"
-
-config SYS_CONFIG_NAME
-	string "Board configuration name"
-	default "xilinx_zynqmp"
-	help
-	  This option contains information about board configuration name.
-	  Based on this option include/configs/<CONFIG_SYS_CONFIG_NAME>.h header
-	  will be used for board configuration.
-
-config SYS_MEM_RSVD_FOR_MMU
-	bool "Reserve memory for MMU Table"
-	help
-	  If defined this option is used to setup different space for
-	  MMU table than the one which will be allocated during
-	  relocation.
-
-config BOOT_INIT_FILE
-	string "boot.bin init register filename"
-	depends on SPL
-	default ""
-	help
-	  Add register writes to boot.bin format (max 256 pairs).
-	  Expect a table of register-value pairs, e.g. "0x12345678 0x4321"
-
-config PMUFW_INIT_FILE
-	string "PMU firmware"
-	depends on SPL
-	default ""
-	help
-	  Include external PMUFW (Platform Management Unit FirmWare) to
-	  a Xilinx bootable image (boot.bin).
-
-config ZYNQMP_USB
-	bool "Configure ZynqMP USB"
-
-config ZYNQMP_NO_DDR
-	bool "Disable DDR MMU mapping"
-	help
-	  This option configures MMU with no DDR to avoid speculative
-	  access to DDR memory where DDR is not present.
-
-config SYS_MALLOC_F_LEN
-	default 0x600
-
-config DEFINE_TCM_OCM_MMAP
-	bool "Define TCM and OCM memory in MMU Table"
-	default y if MP
-	help
-	  This option if enabled defines the TCM and OCM memory and its
-	  memory attributes in MMU table entry.
-
-config ZYNQMP_PSU_INIT_ENABLED
-	bool "Include psu_init"
-	help
-	  Include psu_init to full u-boot. SPL include psu_init by default.
-
-config SPL_ZYNQMP_ALT_BOOTMODE_ENABLED
-	bool "Overwrite SPL bootmode"
-	depends on SPL
-	help
-	  Overwrite bootmode selected via boot mode pins to tell SPL what should
-	  be the next boot device.
-
-config ZYNQ_SDHCI_MAX_FREQ
-	default 200000000
-
-config SPL_ZYNQMP_ALT_BOOTMODE
-	hex
-	default 0x0 if JTAG_MODE
-	default 0x1 if QSPI_MODE_24BIT
-	default 0x2 if QSPI_MODE_32BIT
-	default 0x3 if SD_MODE
-	default 0x4 if NAND_MODE
-	default 0x5 if SD_MODE1
-	default 0x6 if EMMC_MODE
-	default 0x7 if USB_MODE
-	default 0xa if SW_USBHOST_MODE
-	default 0xb if SW_SATA_MODE
-	default 0xe if SD1_LSHFT_MODE
-
-choice
-	prompt "Boot mode"
-	depends on SPL_ZYNQMP_ALT_BOOTMODE_ENABLED
-	default JTAG_MODE
-
-config JTAG_MODE
-	bool "JTAG_MODE"
-
-config QSPI_MODE_24BIT
-	bool "QSPI_MODE_24BIT"
-
-config QSPI_MODE_32BIT
-	bool "QSPI_MODE_32BIT"
-
-config SD_MODE
-	bool "SD_MODE"
-
-config SD_MODE1
-	bool "SD_MODE1"
-
-config NAND_MODE
-	bool "NAND_MODE"
-
-config EMMC_MODE
-	bool "EMMC_MODE"
-
-config USB_MODE
-	bool "USB"
-
-config SW_USBHOST_MODE
-	bool "SW USBHOST_MODE"
-
-config SW_SATA_MODE
-	bool "SW SATA_MODE"
-
-config SD1_LSHFT_MODE
-	bool "SD1_LSHFT_MODE"
-
-endchoice
-
-endif