diff options
Diffstat (limited to 'arch/arm/dts/r8a77990-ebisu.dts')
| -rw-r--r-- | arch/arm/dts/r8a77990-ebisu.dts | 226 |
1 files changed, 115 insertions, 111 deletions
diff --git a/arch/arm/dts/r8a77990-ebisu.dts b/arch/arm/dts/r8a77990-ebisu.dts index c727725899..4fd2b14fbb 100644 --- a/arch/arm/dts/r8a77990-ebisu.dts +++ b/arch/arm/dts/r8a77990-ebisu.dts @@ -19,16 +19,10 @@ }; chosen { - bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp"; + bootargs = "ignore_loglevel rw root=/dev/nfs ip=on"; stdout-path = "serial0:115200n8"; }; - memory@48000000 { - device_type = "memory"; - /* first 128MB is reserved for secure area. */ - reg = <0x0 0x48000000 0x0 0x38000000>; - }; - audio_clkout: audio-clkout { /* * This is same as <&rcar_sound 0> @@ -107,36 +101,10 @@ }; }; - vga { - compatible = "vga-connector"; - - port { - vga_in: endpoint { - remote-endpoint = <&adv7123_out>; - }; - }; - }; - - vga-encoder { - compatible = "adi,adv7123"; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - adv7123_in: endpoint { - remote-endpoint = <&du_out_rgb>; - }; - }; - port@1 { - reg = <1>; - adv7123_out: endpoint { - remote-endpoint = <&vga_in>; - }; - }; - }; + memory@48000000 { + device_type = "memory"; + /* first 128MB is reserved for secure area. */ + reg = <0x0 0x48000000 0x0 0x38000000>; }; reg_1p8v: regulator0 { @@ -157,15 +125,13 @@ regulator-always-on; }; - vbus0_usb2: regulator-vbus0-usb2 { + reg_12p0v: regulator2 { compatible = "regulator-fixed"; - - regulator-name = "USB20_VBUS_CN"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - - gpio = <&gpio6 4 GPIO_ACTIVE_HIGH>; - enable-active-high; + regulator-name = "D12.0V"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + regulator-boot-on; + regulator-always-on; }; rsnd_ak4613: sound { @@ -176,34 +142,24 @@ simple-audio-card,bitclock-master = <&sndcpu>; simple-audio-card,frame-master = <&sndcpu>; - sndcpu: simple-audio-card,cpu { - sound-dai = <&rcar_sound>; - }; - sndcodec: simple-audio-card,codec { sound-dai = <&ak4613>; }; - }; - x12_clk: x12 { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <24576000>; + sndcpu: simple-audio-card,cpu { + sound-dai = <&rcar_sound>; + }; }; - reg_12p0v: regulator2 { + vbus0_usb2: regulator-vbus0-usb2 { compatible = "regulator-fixed"; - regulator-name = "D12.0V"; - regulator-min-microvolt = <12000000>; - regulator-max-microvolt = <12000000>; - regulator-boot-on; - regulator-always-on; - }; - x13_clk: x13 { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <74250000>; + regulator-name = "USB20_VBUS_CN"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + gpio = <&gpio6 4 GPIO_ACTIVE_HIGH>; + enable-active-high; }; vcc_sdhi0: regulator-vcc-sdhi0 { @@ -226,8 +182,7 @@ gpios = <&gpio5 18 GPIO_ACTIVE_HIGH>; gpios-states = <1>; - states = <3300000 1 - 1800000 0>; + states = <3300000 1>, <1800000 0>; }; vcc_sdhi1: regulator-vcc-sdhi1 { @@ -250,8 +205,51 @@ gpios = <&gpio3 15 GPIO_ACTIVE_HIGH>; gpios-states = <1>; - states = <3300000 1 - 1800000 0>; + states = <3300000 1>, <1800000 0>; + }; + + vga { + compatible = "vga-connector"; + + port { + vga_in: endpoint { + remote-endpoint = <&adv7123_out>; + }; + }; + }; + + vga-encoder { + compatible = "adi,adv7123"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + adv7123_in: endpoint { + remote-endpoint = <&du_out_rgb>; + }; + }; + port@1 { + reg = <1>; + adv7123_out: endpoint { + remote-endpoint = <&vga_in>; + }; + }; + }; + }; + + x12_clk: x12 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <24576000>; + }; + + x13_clk: x13 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <74250000>; }; }; @@ -262,7 +260,6 @@ &avb { pinctrl-0 = <&avb_pins>; pinctrl-names = "default"; - renesas,no-ether-link; phy-handle = <&phy0>; status = "okay"; @@ -272,6 +269,14 @@ interrupt-parent = <&gpio2>; interrupts = <21 IRQ_TYPE_LEVEL_LOW>; reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>; + /* + * TX clock internal delay mode is required for reliable + * 1Gbps communication using the KSZ9031RNX phy present on + * the Ebisu board, however, TX clock internal delay mode + * isn't supported on r8a77990. Thus, limit speed to + * 100Mbps for reliable communication. + */ + max-speed = <100>; }; }; @@ -548,6 +553,11 @@ function = "pwm5"; }; + scif2_pins: scif2 { + groups = "scif2_data_a"; + function = "scif2"; + }; + sdhi0_pins: sd0 { groups = "sdhi0_data4", "sdhi0_ctrl"; function = "sdhi0"; @@ -578,20 +588,15 @@ power-source = <1800>; }; - sound_pins: sound { - groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data"; - function = "ssi"; - }; - sound_clk_pins: sound_clk { groups = "audio_clk_a", "audio_clk_b_a", "audio_clk_c_a", "audio_clkout_a", "audio_clkout1_a"; function = "audio_clk"; }; - scif2_pins: scif2 { - groups = "scif2_data_a"; - function = "scif2"; + sound_pins: sound { + groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data"; + function = "ssi"; }; usb0_pins: usb { @@ -629,7 +634,6 @@ /* audio_clkout0/1/2/3 */ #clock-cells = <1>; clock-frequency = <12288000 11289600>; - clkout-lr-synchronous; status = "okay"; @@ -672,38 +676,6 @@ status = "okay"; }; -&ssi1 { - shared-pin; -}; - -&usb2_phy0 { - pinctrl-0 = <&usb0_pins>; - pinctrl-names = "default"; - - vbus-supply = <&vbus0_usb2>; - status = "okay"; -}; - -&usb3_peri0 { - companion = <&xhci0>; - status = "okay"; -}; - -&vin4 { - status = "okay"; -}; - -&vin5 { - status = "okay"; -}; - -&xhci0 { - pinctrl-0 = <&usb30_pins>; - pinctrl-names = "default"; - - status = "okay"; -}; - &sdhi0 { pinctrl-0 = <&sdhi0_pins>; pinctrl-1 = <&sdhi0_pins_uhs>; @@ -747,3 +719,35 @@ non-removable; status = "okay"; }; + +&ssi1 { + shared-pin; +}; + +&usb2_phy0 { + pinctrl-0 = <&usb0_pins>; + pinctrl-names = "default"; + + vbus-supply = <&vbus0_usb2>; + status = "okay"; +}; + +&usb3_peri0 { + companion = <&xhci0>; + status = "okay"; +}; + +&vin4 { + status = "okay"; +}; + +&vin5 { + status = "okay"; +}; + +&xhci0 { + pinctrl-0 = <&usb30_pins>; + pinctrl-names = "default"; + + status = "okay"; +}; |