diff options
Diffstat (limited to 'arch/arm/dts/zynqmp-zcu104-revA.dts')
| -rw-r--r-- | arch/arm/dts/zynqmp-zcu104-revA.dts | 265 |
1 files changed, 265 insertions, 0 deletions
diff --git a/arch/arm/dts/zynqmp-zcu104-revA.dts b/arch/arm/dts/zynqmp-zcu104-revA.dts new file mode 100644 index 0000000000..a0e13d8dc5 --- /dev/null +++ b/arch/arm/dts/zynqmp-zcu104-revA.dts @@ -0,0 +1,265 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * dts file for Xilinx ZynqMP ZCU104 + * + * (C) Copyright 2017 - 2018, Xilinx, Inc. + * + * Michal Simek <michal.simek@xilinx.com> + */ + +/dts-v1/; + +#include "zynqmp.dtsi" +#include "zynqmp-clk-ccf.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/phy/phy.h> + +/ { + model = "ZynqMP ZCU104 RevA"; + compatible = "xlnx,zynqmp-zcu104-revA", "xlnx,zynqmp-zcu104", "xlnx,zynqmp"; + + aliases { + ethernet0 = &gem3; + gpio0 = &gpio; + i2c0 = &i2c1; + mmc0 = &sdhci1; + rtc0 = &rtc; + serial0 = &uart0; + serial1 = &uart1; + serial2 = &dcc; + spi0 = &qspi; + usb0 = &usb0; + }; + + chosen { + bootargs = "earlycon"; + stdout-path = "serial0:115200n8"; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x80000000>; + }; +}; + +&can1 { + status = "okay"; +}; + +&dcc { + status = "okay"; +}; + +&gem3 { + status = "okay"; + phy-handle = <&phy0>; + phy-mode = "rgmii-id"; + phy0: phy@c { + reg = <0xc>; + ti,rx-internal-delay = <0x8>; + ti,tx-internal-delay = <0xa>; + ti,fifo-depth = <0x1>; + }; +}; + +&gpio { + status = "okay"; +}; + +&gpu { + status = "okay"; +}; + +&i2c1 { + status = "okay"; + clock-frequency = <400000>; + + /* Another connection to this bus via PL i2c via PCA9306 - u45 */ + i2c-mux@74 { /* u34 */ + compatible = "nxp,pca9548"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x74>; + i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + /* + * IIC_EEPROM 1kB memory which uses 256B blocks + * where every block has different address. + * 0 - 256B address 0x54 + * 256B - 512B address 0x55 + * 512B - 768B address 0x56 + * 768B - 1024B address 0x57 + */ + eeprom: eeprom@54 { /* u23 */ + compatible = "atmel,24c08"; + reg = <0x54>; + #address-cells = <1>; + #size-cells = <1>; + }; + }; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + clock_8t49n287: clock-generator@6c { /* 8T49N287 - u182 */ + compatible = "idt,8t49n287"; + reg = <0x6c>; + }; + }; + + i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + irps5401_43: irps54012@43 { /* IRPS5401 - u175 */ + #clock-cells = <0>; + compatible = "infineon,irps5401"; + reg = <0x43>; + }; + irps5401_4d: irps54012@4d { /* IRPS5401 - u180 */ + #clock-cells = <0>; + compatible = "infineon,irps5401"; + reg = <0x4d>; + }; + }; + + i2c@4 { + #address-cells = <1>; + #size-cells = <0>; + reg = <4>; + tca6416_u97: gpio@21 { + compatible = "ti,tca6416"; + reg = <0x21>; + gpio-controller; + #gpio-cells = <2>; + /* + * IRQ not connected + * Lines: + * 0 - IRPS5401_ALERT_B + * 1 - HDMI_8T49N241_INT_ALM + * 2 - MAX6643_OT_B + * 3 - MAX6643_FANFAIL_B + * 5 - IIC_MUX_RESET_B + * 6 - GEM3_EXP_RESET_B + * 7 - FMC_LPC_PRSNT_M2C_B + * 4, 10 - 17 - not connected + */ + }; + }; + + i2c@5 { + #address-cells = <1>; + #size-cells = <0>; + reg = <5>; + }; + + i2c@7 { + #address-cells = <1>; + #size-cells = <0>; + reg = <7>; + }; + + /* 3, 6 not connected */ + }; +}; + +&qspi { + status = "okay"; + flash@0 { + compatible = "m25p80"; /* n25q512a 128MiB */ + #address-cells = <1>; + #size-cells = <1>; + reg = <0x0>; + spi-tx-bus-width = <1>; + spi-rx-bus-width = <4>; + spi-max-frequency = <108000000>; /* Based on DC1 spec */ + partition@qspi-fsbl-uboot { /* for testing purpose */ + label = "qspi-fsbl-uboot"; + reg = <0x0 0x100000>; + }; + partition@qspi-linux { /* for testing purpose */ + label = "qspi-linux"; + reg = <0x100000 0x500000>; + }; + partition@qspi-device-tree { /* for testing purpose */ + label = "qspi-device-tree"; + reg = <0x600000 0x20000>; + }; + partition@qspi-rootfs { /* for testing purpose */ + label = "qspi-rootfs"; + reg = <0x620000 0x5E0000>; + }; + }; +}; + +&rtc { + status = "okay"; +}; + +&sata { + status = "okay"; + /* SATA OOB timing settings */ + ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>; + ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>; + ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>; + ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>; + ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>; + ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>; + ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>; + ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>; + phy-names = "sata-phy"; + phys = <&lane3 PHY_TYPE_SATA 1 1 125000000>; +}; + +/* SD1 with level shifter */ +&sdhci1 { + status = "okay"; + no-1-8-v; + xlnx,mio_bank = <1>; + disable-wp; +}; + +&serdes { + status = "okay"; +}; + +&uart0 { + status = "okay"; +}; + +&uart1 { + status = "okay"; +}; + +/* ULPI SMSC USB3320 */ +&usb0 { + status = "okay"; +}; + +&dwc3_0 { + status = "okay"; + dr_mode = "host"; + snps,usb3_lpm_capable; + phy-names = "usb3-phy"; + phys = <&lane2 PHY_TYPE_USB3 0 2 26000000>; + maximum-speed = "super-speed"; +}; + +&watchdog0 { + status = "okay"; +}; + +&xilinx_ams { + status = "okay"; +}; + +&ams_ps { + status = "okay"; +}; + +&ams_pl { + status = "okay"; +}; |