diff options
Diffstat (limited to 'arch/arm/mach-omap2/vc.c')
| -rw-r--r-- | arch/arm/mach-omap2/vc.c | 151 |
1 files changed, 151 insertions, 0 deletions
diff --git a/arch/arm/mach-omap2/vc.c b/arch/arm/mach-omap2/vc.c new file mode 100644 index 0000000000..a68f1d145d --- /dev/null +++ b/arch/arm/mach-omap2/vc.c @@ -0,0 +1,151 @@ +/* + * Voltage Controller implementation for OMAP + * + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * Nishanth Menon + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed "as is" WITHOUT ANY WARRANTY of any + * kind, whether express or implied; without even the implied warranty + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <common.h> +#include <asm/omap_common.h> +#include <asm/arch/sys_proto.h> +#include <asm/arch/clock.h> + +/* + * Define Master code if there are multiple masters on the I2C_SR bus. + * Normally not required + */ +#ifndef CONFIG_OMAP_VC_I2C_HS_MCODE +#define CONFIG_OMAP_VC_I2C_HS_MCODE 0x0 +#endif + +/* Register defines and masks for VC IP Block */ +/* PRM_VC_CFG_I2C_MODE */ +#define PRM_VC_CFG_I2C_MODE_DFILTEREN_BIT (0x1 << 6) +#define PRM_VC_CFG_I2C_MODE_SRMODEEN_BIT (0x1 << 4) +#define PRM_VC_CFG_I2C_MODE_HSMODEEN_BIT (0x1 << 3) +#define PRM_VC_CFG_I2C_MODE_HSMCODE_SHIFT 0x0 +#define PRM_VC_CFG_I2C_MODE_HSMCODE_MASK 0x3 + +/* PRM_VC_CFG_I2C_CLK */ +#define PRM_VC_CFG_I2C_CLK_HSCLL_SHIFT 24 +#define PRM_VC_CFG_I2C_CLK_HSCLL_MASK 0xFF +#define PRM_VC_CFG_I2C_CLK_HSCLH_SHIFT 16 +#define PRM_VC_CFG_I2C_CLK_HSCLH_MASK 0xFF +#define PRM_VC_CFG_I2C_CLK_SCLH_SHIFT 0 +#define PRM_VC_CFG_I2C_CLK_SCLH_MASK 0xFF +#define PRM_VC_CFG_I2C_CLK_SCLL_SHIFT 8 +#define PRM_VC_CFG_I2C_CLK_SCLL_MASK (0xFF << 8) + +/* PRM_VC_VAL_BYPASS */ +#define PRM_VC_VAL_BYPASS_VALID_BIT (0x1 << 24) +#define PRM_VC_VAL_BYPASS_SLAVEADDR_SHIFT 0 +#define PRM_VC_VAL_BYPASS_SLAVEADDR_MASK 0x7F +#define PRM_VC_VAL_BYPASS_REGADDR_SHIFT 8 +#define PRM_VC_VAL_BYPASS_REGADDR_MASK 0xFF +#define PRM_VC_VAL_BYPASS_DATA_SHIFT 16 +#define PRM_VC_VAL_BYPASS_DATA_MASK 0xFF + +/** + * omap_vc_init() - Initialization for Voltage controller + * @speed_khz: I2C buspeed in KHz + */ +static void omap_vc_init(u16 speed_khz) +{ + u32 val; + u32 sys_clk_khz, cycles_hi, cycles_low; + + sys_clk_khz = get_sys_clk_freq() / 1000; + + if (speed_khz > 400) { + puts("higher speed requested - throttle to 400Khz\n"); + speed_khz = 400; + } + + /* + * Setup the dedicated I2C controller for Voltage Control + * I2C clk - high period 40% low period 60% + */ + speed_khz /= 10; + cycles_hi = sys_clk_khz * 4 / speed_khz; + cycles_low = sys_clk_khz * 6 / speed_khz; + /* values to be set in register - less by 5 & 7 respectively */ + cycles_hi -= 5; + cycles_low -= 7; + val = (cycles_hi << PRM_VC_CFG_I2C_CLK_SCLH_SHIFT) | + (cycles_low << PRM_VC_CFG_I2C_CLK_SCLL_SHIFT); + writel(val, (*prcm)->prm_vc_cfg_i2c_clk); + + val = CONFIG_OMAP_VC_I2C_HS_MCODE << + PRM_VC_CFG_I2C_MODE_HSMCODE_SHIFT; + /* No HS mode for now */ + val &= ~PRM_VC_CFG_I2C_MODE_HSMODEEN_BIT; + writel(val, (*prcm)->prm_vc_cfg_i2c_mode); +} + +/** + * omap_vc_bypass_send_value() - Send a data using VC Bypass command + * @sa: 7 bit I2C slave address of the PMIC + * @reg_addr: I2C register address(8 bit) address in PMIC + * @reg_data: what 8 bit data to write + */ +int omap_vc_bypass_send_value(u8 sa, u8 reg_addr, u8 reg_data) +{ + /* + * Unfortunately we need to loop here instead of a defined time + * use arbitary large value + */ + u32 timeout = 0xFFFF; + u32 reg_val; + + sa &= PRM_VC_VAL_BYPASS_SLAVEADDR_MASK; + reg_addr &= PRM_VC_VAL_BYPASS_REGADDR_MASK; + reg_data &= PRM_VC_VAL_BYPASS_DATA_MASK; + + /* program VC to send data */ + reg_val = sa << PRM_VC_VAL_BYPASS_SLAVEADDR_SHIFT | + reg_addr << PRM_VC_VAL_BYPASS_REGADDR_SHIFT | + reg_data << PRM_VC_VAL_BYPASS_DATA_SHIFT; + writel(reg_val, (*prcm)->prm_vc_val_bypass); + + /* Signal VC to send data */ + writel(reg_val | PRM_VC_VAL_BYPASS_VALID_BIT, + (*prcm)->prm_vc_val_bypass); + + /* Wait on VC to complete transmission */ + do { + reg_val = readl((*prcm)->prm_vc_val_bypass) & + PRM_VC_VAL_BYPASS_VALID_BIT; + if (!reg_val) + break; + + sdelay(100); + } while (--timeout); + + /* Optional: cleanup PRM_IRQSTATUS_Ax */ + /* In case we can do something about it in future.. */ + if (!timeout) + return -1; + + /* All good.. */ + return 0; +} + +void sri2c_init(void) +{ + static int sri2c = 1; + + if (sri2c) { + omap_vc_init(PRM_VC_I2C_CHANNEL_FREQ_KHZ); + sri2c = 0; + } + return; +} |