diff options
Diffstat (limited to 'arch/arm')
| -rw-r--r-- | arch/arm/dts/armada-388-clearfog.dts | 63 |
1 files changed, 6 insertions, 57 deletions
diff --git a/arch/arm/dts/armada-388-clearfog.dts b/arch/arm/dts/armada-388-clearfog.dts index a0b566a5ae..1403600e5b 100644 --- a/arch/arm/dts/armada-388-clearfog.dts +++ b/arch/arm/dts/armada-388-clearfog.dts @@ -50,6 +50,7 @@ #include <dt-bindings/input/input.h> #include <dt-bindings/gpio/gpio.h> #include "armada-388.dtsi" +#include "armada-38x-solidrun-microsom.dtsi" / { model = "SolidRun Clearfog A1"; @@ -70,11 +71,6 @@ stdout-path = "serial0:115200n8"; }; - memory { - device_type = "memory"; - reg = <0x00000000 0x10000000>; /* 256 MB */ - }; - reg_3p3v: regulator-3p3v { compatible = "regulator-fixed"; regulator-name = "3P3V"; @@ -84,11 +80,6 @@ }; soc { - ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 - MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000 - MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000 - MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000>; - internal-regs { ethernet@30000 { mac-address = [00 50 43 02 02 02]; @@ -108,15 +99,6 @@ status = "okay"; }; - ethernet@70000 { - mac-address = [00 50 43 02 02 01]; - pinctrl-0 = <&ge0_rgmii_pins>; - pinctrl-names = "default"; - phy = <&phy_dedicated>; - phy-mode = "rgmii-id"; - status = "okay"; - }; - i2c@11000 { /* Is there anything on this? */ clock-frequency = <100000>; @@ -226,22 +208,6 @@ status = "okay"; }; - mdio@72004 { - pinctrl-0 = <&mdio_pins>; - pinctrl-names = "default"; - - phy_dedicated: ethernet-phy@0 { - /* - * Annoyingly, the marvell phy driver - * configures the LED register, rather - * than preserving reset-loaded setting. - * We undo that rubbish here. - */ - marvell,reg-init = <3 16 0 0x101e>; - reg = <0>; - }; - }; - pinctrl@18000 { clearfog_dsa0_clk_pins: clearfog-dsa0-clk-pins { marvell,pins = "mpp46"; @@ -260,12 +226,6 @@ marvell,pins = "mpp20"; marvell,function = "gpio"; }; - clearfog_sdhci_pins: clearfog-sdhci-pins { - marvell,pins = "mpp21", "mpp28", - "mpp37", "mpp38", - "mpp39", "mpp40"; - marvell,function = "sd0"; - }; clearfog_spi1_cs_pins: spi1-cs-pins { marvell,pins = "mpp55"; marvell,function = "spi1"; @@ -311,7 +271,7 @@ bus-width = <4>; cd-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>; no-1-8-v; - pinctrl-0 = <&clearfog_sdhci_pins + pinctrl-0 = <µsom_sdhci_pins &clearfog_sdhci_cd_pins>; pinctrl-names = "default"; status = "okay"; @@ -319,13 +279,6 @@ wp-inverted; }; - serial@12000 { - pinctrl-0 = <&uart0_pins>; - pinctrl-names = "default"; - status = "okay"; - u-boot,dm-pre-reloc; - }; - serial@12100 { /* mikrobus uart */ pinctrl-0 = <&mikro_uart_pins>; @@ -342,14 +295,6 @@ pinctrl-0 = <&spi1_pins &clearfog_spi1_cs_pins &mikro_spi_pins>; pinctrl-names = "default"; status = "okay"; - - spi-flash@0 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "w25q32", "jedec,spi-nor", "spi-flash"; - reg = <0>; /* Chip select 0 */ - spi-max-frequency = <3000000>; - }; }; usb3@f8000 { @@ -457,6 +402,10 @@ }; }; +&w25q32 { + status = "okay"; +}; + /* +#define A38x_CUSTOMER_BOARD_1_MPP16_23 0x00400011 MPP18: gpio ? (pca9655 int?) |