diff options
Diffstat (limited to 'arch/arm')
68 files changed, 1976 insertions, 255 deletions
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 171ad03429..79ccc06d5c 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -177,10 +177,6 @@ config TARGET_ETHERNUT5 bool "Support ethernut5" select CPU_ARM926EJS -config TARGET_TOP9000 - bool "Support top9000" - select CPU_ARM926EJS - config TARGET_MEESC bool "Support meesc" select CPU_ARM926EJS @@ -631,6 +627,9 @@ config TARGET_HUMMINGBOARD bool "Support hummingboard" select CPU_V7 +config TARGET_KOSAGI_NOVENA + bool "Support Kosagi Novena" + config TARGET_TQMA6 bool "TQ Systems TQMa6 board" select CPU_V7 @@ -667,30 +666,8 @@ config TARGET_SOCFPGA_CYCLONE5 select CPU_V7 select SUPPORT_SPL -config TARGET_SUN4I - bool "Support sun4i" - select CPU_V7 - select SUPPORT_SPL - -config TARGET_SUN5I - bool "Support sun5i" - select CPU_V7 - select SUPPORT_SPL - -config TARGET_SUN6I - bool "Support sun6i" - select CPU_V7 - select SUPPORT_SPL - -config TARGET_SUN7I - bool "Support sun7i" - select CPU_V7 - select SUPPORT_SPL - -config TARGET_SUN8I - bool "Support sun8i" - select CPU_V7 - select SUPPORT_SPL +config ARCH_SUNXI + bool "Support sunxi (Allwinner) SoCs" config TARGET_SNOWBALL bool "Support snowball" @@ -918,6 +895,7 @@ source "board/imx31_phycore/Kconfig" source "board/isee/igep0033/Kconfig" source "board/jornada/Kconfig" source "board/karo/tx25/Kconfig" +source "board/kosagi/novena/Kconfig" source "board/logicpd/imx27lite/Kconfig" source "board/logicpd/imx31_litekit/Kconfig" source "board/maxbcm/Kconfig" @@ -972,4 +950,6 @@ source "board/woodburn/Kconfig" source "board/xaeniax/Kconfig" source "board/zipitz2/Kconfig" +source "arch/arm/Kconfig.debug" + endmenu diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug new file mode 100644 index 0000000000..624bcf4682 --- /dev/null +++ b/arch/arm/Kconfig.debug @@ -0,0 +1,64 @@ +menu "ARM debug" + +config DEBUG_LL + bool "Low-level debugging functions" + depends on !ARM64 + help + Say Y here to include definitions of printascii, printch, printhex + in U-Boot. This is helpful if you are debugging code that + executes before the console is initialized. + +choice + prompt "Low-level debugging port" + depends on DEBUG_LL + + config DEBUG_LL_UART_8250 + bool "Low-level debugging via 8250 UART" + help + Say Y here if you wish the debug print routes to direct + their output to an 8250 UART. You can use this option + to provide the parameters for the 8250 UART rather than + selecting one of the platform specific options above if + you know the parameters for the port. + + This option is preferred over the platform specific + options; the platform specific options are deprecated + and will be soon removed. + +endchoice + +config DEBUG_LL_INCLUDE + string + depends on DEBUG_LL + default "debug/8250.S" if DEBUG_LL_UART_8250 || DEBUG_UART_8250 + default "mach/debug-macro.S" + +# Compatibility options for 8250 +config DEBUG_UART_8250 + bool + +config DEBUG_UART_PHYS + hex "Physical base address of debug UART" + depends on DEBUG_LL_UART_8250 || DEBUG_UART_8250 + +# This is not used in U-Boot +config DEBUG_UART_VIRT + hex + default DEBUG_UART_PHYS + depends on DEBUG_LL_UART_8250 || DEBUG_UART_8250 + +config DEBUG_UART_8250_SHIFT + int "Register offset shift for the 8250 debug UART" + depends on DEBUG_LL_UART_8250 || DEBUG_UART_8250 + default 2 + +config DEBUG_UART_8250_WORD + bool "Use 32-bit accesses for 8250 UART" + depends on DEBUG_LL_UART_8250 || DEBUG_UART_8250 + depends on DEBUG_UART_8250_SHIFT >= 2 + +config DEBUG_UART_8250_FLOW_CONTROL + bool "Enable flow control for 8250 UART" + depends on DEBUG_LL_UART_8250 || DEBUG_UART_8250 + +endmenu diff --git a/arch/arm/cpu/arm926ejs/cache.c b/arch/arm/cpu/arm926ejs/cache.c index e86c2edd3b..8d7873c9af 100644 --- a/arch/arm/cpu/arm926ejs/cache.c +++ b/arch/arm/cpu/arm926ejs/cache.c @@ -99,7 +99,4 @@ void flush_cache(unsigned long start, unsigned long size) /* * Stub implementations for l2 cache operations */ -void __l2_cache_disable(void) {} - -void l2_cache_disable(void) - __attribute__((weak, alias("__l2_cache_disable"))); +__weak void l2_cache_disable(void) {} diff --git a/arch/arm/cpu/arm926ejs/mxs/mxs.c b/arch/arm/cpu/arm926ejs/mxs/mxs.c index 365542fe0b..ef130aea42 100644 --- a/arch/arm/cpu/arm926ejs/mxs/mxs.c +++ b/arch/arm/cpu/arm926ejs/mxs/mxs.c @@ -83,7 +83,9 @@ void mx28_fixup_vt(uint32_t start_addr) int i; for (i = 0; i < 8; i++) { + /* cppcheck-suppress nullPointer */ vt[i] = ldr_pc; + /* cppcheck-suppress nullPointer */ vt[i + 8] = start_addr + (4 * i); } } diff --git a/arch/arm/cpu/arm926ejs/mxs/spl_boot.c b/arch/arm/cpu/arm926ejs/mxs/spl_boot.c index d3e136991a..d29b9aaf3d 100644 --- a/arch/arm/cpu/arm926ejs/mxs/spl_boot.c +++ b/arch/arm/cpu/arm926ejs/mxs/spl_boot.c @@ -118,6 +118,8 @@ static void mxs_spl_fixup_vectors(void) * fine. */ extern uint32_t _start; + + /* cppcheck-suppress nullPointer */ memcpy(0x0, &_start, 0x60); } diff --git a/arch/arm/cpu/arm926ejs/mxs/timer.c b/arch/arm/cpu/arm926ejs/mxs/timer.c index 99d3fb8731..f2e72257d1 100644 --- a/arch/arm/cpu/arm926ejs/mxs/timer.c +++ b/arch/arm/cpu/arm926ejs/mxs/timer.c @@ -91,6 +91,8 @@ unsigned long long get_ticks(void) TIMROT_RUNNING_COUNTn_RUNNING_COUNT_OFFSET; #elif defined(CONFIG_MX28) now = readl(&timrot_regs->hw_timrot_running_count0); +#else +#error "Don't know how to read timrot_regs" #endif if (lastdec >= now) { diff --git a/arch/arm/cpu/armv7/am33xx/sys_info.c b/arch/arm/cpu/armv7/am33xx/sys_info.c index 2ce682f6b1..781d83fc72 100644 --- a/arch/arm/cpu/armv7/am33xx/sys_info.c +++ b/arch/arm/cpu/armv7/am33xx/sys_info.c @@ -18,6 +18,7 @@ #include <asm/arch/cpu.h> #include <asm/arch/clock.h> #include <power/tps65910.h> +#include <linux/compiler.h> struct ctrl_stat *cstat = (struct ctrl_stat *)CTRL_BASE; @@ -51,11 +52,11 @@ u32 get_cpu_type(void) /** * get_board_rev() - setup to pass kernel board revision information - * returns:(bit[0-3] sub version, higher bit[7-4] is higher version) + * returns: 0 for the ATAG REVISION tag value. */ -u32 get_board_rev(void) +u32 __weak get_board_rev(void) { - return BOARD_REV_ID; + return 0; } /** diff --git a/arch/arm/cpu/armv7/mx6/clock.c b/arch/arm/cpu/armv7/mx6/clock.c index d200531030..6c9c78c11a 100644 --- a/arch/arm/cpu/armv7/mx6/clock.c +++ b/arch/arm/cpu/armv7/mx6/clock.c @@ -312,6 +312,10 @@ static u32 get_ipg_per_clk(void) u32 reg, perclk_podf; reg = __raw_readl(&imx_ccm->cscmr1); +#if (defined(CONFIG_MX6SL) || defined(CONFIG_MX6SX)) + if (reg & MXC_CCM_CSCMR1_PER_CLK_SEL_MASK) + return MXC_HCLK; /* OSC 24Mhz */ +#endif perclk_podf = reg & MXC_CCM_CSCMR1_PERCLK_PODF_MASK; return get_ipg_clk() / (perclk_podf + 1); diff --git a/arch/arm/cpu/armv7/mx6/soc.c b/arch/arm/cpu/armv7/mx6/soc.c index dd5aaa286a..affbf7f702 100644 --- a/arch/arm/cpu/armv7/mx6/soc.c +++ b/arch/arm/cpu/armv7/mx6/soc.c @@ -240,6 +240,18 @@ static void clear_mmdc_ch_mask(void) writel(0, &mxc_ccm->ccdr); } +#ifdef CONFIG_MX6SL +static void set_preclk_from_osc(void) +{ + struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; + u32 reg; + + reg = readl(&mxc_ccm->cscmr1); + reg |= MXC_CCM_CSCMR1_PER_CLK_SEL_MASK; + writel(reg, &mxc_ccm->cscmr1); +} +#endif + int arch_cpu_init(void) { init_aips(); @@ -255,6 +267,11 @@ int arch_cpu_init(void) if (mxc_get_clock(MXC_ARM_CLK) == 396000000) set_ahb_rate(132000000); + /* Set perclk to source from OSC 24MHz */ +#if defined(CONFIG_MX6SL) + set_preclk_from_osc(); +#endif + imx_set_wdog_powerdown(false); /* Disable PDE bit of WMCR register */ #ifdef CONFIG_APBH_DMA diff --git a/arch/arm/cpu/armv7/omap3/Kconfig b/arch/arm/cpu/armv7/omap3/Kconfig index c215404469..a029379a4f 100644 --- a/arch/arm/cpu/armv7/omap3/Kconfig +++ b/arch/arm/cpu/armv7/omap3/Kconfig @@ -22,6 +22,9 @@ config TARGET_CM_T35 bool "CompuLab CM-T3530 and CM-T3730 boards" select SUPPORT_SPL +config TARGET_CM_T3517 + bool "CompuLab CM-T3517 boards" + config TARGET_DEVKIT8000 bool "TimLL OMAP3 Devkit8000" select SUPPORT_SPL @@ -98,6 +101,7 @@ source "board/teejet/mt_ventoux/Kconfig" source "board/ti/sdp3430/Kconfig" source "board/ti/beagle/Kconfig" source "board/compulab/cm_t35/Kconfig" +source "board/compulab/cm_t3517/Kconfig" source "board/timll/devkit8000/Kconfig" source "board/ti/evm/Kconfig" source "board/isee/igep00x0/Kconfig" diff --git a/arch/arm/cpu/armv7/rmobile/Kconfig b/arch/arm/cpu/armv7/rmobile/Kconfig index c46a0cc9b8..8444d4224a 100644 --- a/arch/arm/cpu/armv7/rmobile/Kconfig +++ b/arch/arm/cpu/armv7/rmobile/Kconfig @@ -23,6 +23,11 @@ endchoice config SYS_SOC default "rmobile" +config RMOBILE_EXTRAM_BOOT + bool "Enable boot from RAM" + depends on TARGET_ALT || TARGET_KOELSCH || TARGET_LAGER + default n + source "board/atmark-techno/armadillo-800eva/Kconfig" source "board/renesas/koelsch/Kconfig" source "board/renesas/lager/Kconfig" diff --git a/arch/arm/cpu/armv7/rmobile/lowlevel_init_ca15.S b/arch/arm/cpu/armv7/rmobile/lowlevel_init_ca15.S index 879e0e097f..d47546a11d 100644 --- a/arch/arm/cpu/armv7/rmobile/lowlevel_init_ca15.S +++ b/arch/arm/cpu/armv7/rmobile/lowlevel_init_ca15.S @@ -60,17 +60,10 @@ do_lowlevel_init: cmp r1, #3 /* has already been set up */ bicne r0, r0, #0xe7 orrne r0, r0, #0x83 /* L2CTLR[7:6] + L2CTLR[2:0] */ - - ldr r2, =0xFF000044 /* PRR */ - ldr r1, [r2] - and r1, r1, #0x7F00 - lsrs r1, r1, #8 - cmp r1, #0x45 /* 0x45 is ID of r8a7790 */ - bne L2CTLR_5_SKIP +#if defined(CONFIG_R8A7790) orrne r0, r0, #0x20 /* L2CTLR[5] */ -L2CTLR_5_SKIP: +#endif mcrne p15, 1, r0, c9, c0, 2 - _exit_init_l2_a15: ldr r3, =(CONFIG_SYS_INIT_SP_ADDR) sub sp, r3, #4 diff --git a/arch/arm/cpu/armv7/sunxi/Makefile b/arch/arm/cpu/armv7/sunxi/Makefile index 24f1daee64..82dbf764e4 100644 --- a/arch/arm/cpu/armv7/sunxi/Makefile +++ b/arch/arm/cpu/armv7/sunxi/Makefile @@ -11,13 +11,13 @@ obj-y += timer.o obj-y += board.o obj-y += clock.o obj-y += pinmux.o -obj-$(CONFIG_SUN6I) += prcm.o -obj-$(CONFIG_SUN8I) += prcm.o -obj-$(CONFIG_SUN4I) += clock_sun4i.o -obj-$(CONFIG_SUN5I) += clock_sun4i.o -obj-$(CONFIG_SUN6I) += clock_sun6i.o -obj-$(CONFIG_SUN7I) += clock_sun4i.o -obj-$(CONFIG_SUN8I) += clock_sun6i.o +obj-$(CONFIG_MACH_SUN6I) += prcm.o +obj-$(CONFIG_MACH_SUN8I) += prcm.o +obj-$(CONFIG_MACH_SUN4I) += clock_sun4i.o +obj-$(CONFIG_MACH_SUN5I) += clock_sun4i.o +obj-$(CONFIG_MACH_SUN6I) += clock_sun6i.o +obj-$(CONFIG_MACH_SUN7I) += clock_sun4i.o +obj-$(CONFIG_MACH_SUN8I) += clock_sun6i.o ifndef CONFIG_SPL_BUILD obj-y += cpu_info.o @@ -27,9 +27,9 @@ endif endif ifdef CONFIG_SPL_BUILD -obj-$(CONFIG_SUN4I) += dram.o -obj-$(CONFIG_SUN5I) += dram.o -obj-$(CONFIG_SUN7I) += dram.o +obj-$(CONFIG_MACH_SUN4I) += dram.o +obj-$(CONFIG_MACH_SUN5I) += dram.o +obj-$(CONFIG_MACH_SUN7I) += dram.o ifdef CONFIG_SPL_FEL obj-y += start.o endif diff --git a/arch/arm/cpu/armv7/sunxi/board.c b/arch/arm/cpu/armv7/sunxi/board.c index 06eb6768e8..6c812fc6e9 100644 --- a/arch/arm/cpu/armv7/sunxi/board.c +++ b/arch/arm/cpu/armv7/sunxi/board.c @@ -51,7 +51,7 @@ u32 spl_boot_mode(void) int gpio_init(void) { #if CONFIG_CONS_INDEX == 1 && defined(CONFIG_UART0_PORT_F) -#if defined(CONFIG_SUN4I) || defined(CONFIG_SUN7I) +#if defined(CONFIG_MACH_SUN4I) || defined(CONFIG_MACH_SUN7I) /* disable GPB22,23 as uart0 tx,rx to avoid conflict */ sunxi_gpio_set_cfgpin(SUNXI_GPB(22), SUNXI_GPIO_INPUT); sunxi_gpio_set_cfgpin(SUNXI_GPB(23), SUNXI_GPIO_INPUT); @@ -59,23 +59,23 @@ int gpio_init(void) sunxi_gpio_set_cfgpin(SUNXI_GPF(2), SUNXI_GPF2_UART0_TX); sunxi_gpio_set_cfgpin(SUNXI_GPF(4), SUNXI_GPF4_UART0_RX); sunxi_gpio_set_pull(SUNXI_GPF(4), 1); -#elif CONFIG_CONS_INDEX == 1 && (defined(CONFIG_SUN4I) || defined(CONFIG_SUN7I)) +#elif CONFIG_CONS_INDEX == 1 && (defined(CONFIG_MACH_SUN4I) || defined(CONFIG_MACH_SUN7I)) sunxi_gpio_set_cfgpin(SUNXI_GPB(22), SUN4I_GPB22_UART0_TX); sunxi_gpio_set_cfgpin(SUNXI_GPB(23), SUN4I_GPB23_UART0_RX); sunxi_gpio_set_pull(SUNXI_GPB(23), SUNXI_GPIO_PULL_UP); -#elif CONFIG_CONS_INDEX == 1 && defined(CONFIG_SUN5I) +#elif CONFIG_CONS_INDEX == 1 && defined(CONFIG_MACH_SUN5I) sunxi_gpio_set_cfgpin(SUNXI_GPB(19), SUN5I_GPB19_UART0_TX); sunxi_gpio_set_cfgpin(SUNXI_GPB(20), SUN5I_GPB20_UART0_RX); sunxi_gpio_set_pull(SUNXI_GPB(20), SUNXI_GPIO_PULL_UP); -#elif CONFIG_CONS_INDEX == 1 && defined(CONFIG_SUN6I) +#elif CONFIG_CONS_INDEX == 1 && defined(CONFIG_MACH_SUN6I) sunxi_gpio_set_cfgpin(SUNXI_GPH(20), SUN6I_GPH20_UART0_TX); sunxi_gpio_set_cfgpin(SUNXI_GPH(21), SUN6I_GPH21_UART0_RX); sunxi_gpio_set_pull(SUNXI_GPH(21), SUNXI_GPIO_PULL_UP); -#elif CONFIG_CONS_INDEX == 2 && defined(CONFIG_SUN5I) +#elif CONFIG_CONS_INDEX == 2 && defined(CONFIG_MACH_SUN5I) sunxi_gpio_set_cfgpin(SUNXI_GPG(3), SUN5I_GPG3_UART1_TX); sunxi_gpio_set_cfgpin(SUNXI_GPG(4), SUN5I_GPG4_UART1_RX); sunxi_gpio_set_pull(SUNXI_GPG(4), SUNXI_GPIO_PULL_UP); -#elif CONFIG_CONS_INDEX == 5 && defined(CONFIG_SUN8I) +#elif CONFIG_CONS_INDEX == 5 && defined(CONFIG_MACH_SUN8I) sunxi_gpio_set_cfgpin(SUNXI_GPL(2), SUN8I_GPL2_R_UART_TX); sunxi_gpio_set_cfgpin(SUNXI_GPL(3), SUN8I_GPL3_R_UART_RX); sunxi_gpio_set_pull(SUNXI_GPL(3), SUNXI_GPIO_PULL_UP); @@ -88,7 +88,7 @@ int gpio_init(void) void reset_cpu(ulong addr) { -#if defined(CONFIG_SUN4I) || defined(CONFIG_SUN5I) || defined(CONFIG_SUN7I) +#if defined(CONFIG_MACH_SUN4I) || defined(CONFIG_MACH_SUN5I) || defined(CONFIG_MACH_SUN7I) static const struct sunxi_wdog *wdog = &((struct sunxi_timer_reg *)SUNXI_TIMER_BASE)->wdog; @@ -100,7 +100,7 @@ void reset_cpu(ulong addr) /* sun5i sometimes gets stuck without this */ writel(WDT_MODE_RESET_EN | WDT_MODE_EN, &wdog->mode); } -#else /* CONFIG_SUN6I || CONFIG_SUN8I || .. */ +#else /* CONFIG_MACH_SUN6I || CONFIG_MACH_SUN8I || .. */ static const struct sunxi_wdog *wdog = ((struct sunxi_timer_reg *)SUNXI_TIMER_BASE)->wdog; @@ -114,8 +114,8 @@ void reset_cpu(ulong addr) /* do some early init */ void s_init(void) { -#if !defined CONFIG_SPL_BUILD && (defined CONFIG_SUN7I || \ - defined CONFIG_SUN6I || defined CONFIG_SUN8I) +#if !defined CONFIG_SPL_BUILD && (defined CONFIG_MACH_SUN7I || \ + defined CONFIG_MACH_SUN6I || defined CONFIG_MACH_SUN8I) /* Enable SMP mode for CPU0, by setting bit 6 of Auxiliary Ctl reg */ asm volatile( "mrc p15, 0, r0, c1, c0, 1\n" diff --git a/arch/arm/cpu/armv7/sunxi/clock_sun4i.c b/arch/arm/cpu/armv7/sunxi/clock_sun4i.c index 4a0d64fb30..a0e49d179f 100644 --- a/arch/arm/cpu/armv7/sunxi/clock_sun4i.c +++ b/arch/arm/cpu/armv7/sunxi/clock_sun4i.c @@ -35,7 +35,7 @@ void clock_init_safe(void) APB0_DIV_1 << APB0_DIV_SHIFT | CPU_CLK_SRC_PLL1 << CPU_CLK_SRC_SHIFT, &ccm->cpu_ahb_apb0_cfg); -#ifdef CONFIG_SUN7I +#ifdef CONFIG_MACH_SUN7I setbits_le32(&ccm->ahb_gate0, 0x1 << AHB_GATE_OFFSET_DMA); #endif writel(PLL6_CFG_DEFAULT, &ccm->pll6_cfg); diff --git a/arch/arm/cpu/armv7/sunxi/cpu_info.c b/arch/arm/cpu/armv7/sunxi/cpu_info.c index 4f2a09cd2e..41b9add297 100644 --- a/arch/arm/cpu/armv7/sunxi/cpu_info.c +++ b/arch/arm/cpu/armv7/sunxi/cpu_info.c @@ -13,9 +13,9 @@ #ifdef CONFIG_DISPLAY_CPUINFO int print_cpuinfo(void) { -#ifdef CONFIG_SUN4I +#ifdef CONFIG_MACH_SUN4I puts("CPU: Allwinner A10 (SUN4I)\n"); -#elif defined CONFIG_SUN5I +#elif defined CONFIG_MACH_SUN5I u32 val = readl(SUNXI_SID_BASE + 0x08); switch ((val >> 12) & 0xf) { case 0: puts("CPU: Allwinner A12 (SUN5I)\n"); break; @@ -23,11 +23,11 @@ int print_cpuinfo(void) case 7: puts("CPU: Allwinner A10s (SUN5I)\n"); break; default: puts("CPU: Allwinner A1X (SUN5I)\n"); } -#elif defined CONFIG_SUN6I +#elif defined CONFIG_MACH_SUN6I puts("CPU: Allwinner A31 (SUN6I)\n"); -#elif defined CONFIG_SUN7I +#elif defined CONFIG_MACH_SUN7I puts("CPU: Allwinner A20 (SUN7I)\n"); -#elif defined CONFIG_SUN8I +#elif defined CONFIG_MACH_SUN8I puts("CPU: Allwinner A23 (SUN8I)\n"); #else #warning Please update cpu_info.c with correct CPU information diff --git a/arch/arm/cpu/armv7/sunxi/dram.c b/arch/arm/cpu/armv7/sunxi/dram.c index 3cf3cbf19a..dc9fdb930b 100644 --- a/arch/arm/cpu/armv7/sunxi/dram.c +++ b/arch/arm/cpu/armv7/sunxi/dram.c @@ -74,7 +74,7 @@ static void mctl_ddr3_reset(void) struct sunxi_dram_reg *dram = (struct sunxi_dram_reg *)SUNXI_DRAMC_BASE; -#ifdef CONFIG_SUN4I +#ifdef CONFIG_MACH_SUN4I struct sunxi_timer_reg *timer = (struct sunxi_timer_reg *)SUNXI_TIMER_BASE; u32 reg_val; @@ -113,7 +113,7 @@ static void mctl_set_drive(void) { struct sunxi_dram_reg *dram = (struct sunxi_dram_reg *)SUNXI_DRAMC_BASE; -#ifdef CONFIG_SUN7I +#ifdef CONFIG_MACH_SUN7I clrsetbits_le32(&dram->mcr, DRAM_MCR_MODE_NORM(0x3) | (0x3 << 28), #else clrsetbits_le32(&dram->mcr, DRAM_MCR_MODE_NORM(0x3), @@ -202,7 +202,7 @@ static void mctl_enable_dllx(u32 phase) } static u32 hpcr_value[32] = { -#ifdef CONFIG_SUN5I +#ifdef CONFIG_MACH_SUN5I 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, @@ -212,7 +212,7 @@ static u32 hpcr_value[32] = { 0x0301, 0x0301, 0x0301, 0x0301, 0x0301, 0x0301, 0x0301, 0 #endif -#ifdef CONFIG_SUN4I +#ifdef CONFIG_MACH_SUN4I 0x0301, 0x0301, 0x0301, 0x0301, 0x0301, 0x0301, 0, 0, 0, 0, 0, 0, @@ -222,7 +222,7 @@ static u32 hpcr_value[32] = { 0x1035, 0x1031, 0x0731, 0x1035, 0x1031, 0x0301, 0x0301, 0x0731 #endif -#ifdef CONFIG_SUN7I +#ifdef CONFIG_MACH_SUN7I 0x0301, 0x0301, 0x0301, 0x0301, 0x0301, 0x0301, 0x0301, 0x0301, 0, 0, 0, 0, @@ -304,7 +304,7 @@ static void mctl_setup_dram_clock(u32 clk, u32 mbus_clk) setbits_le32(&ccm->pll5_cfg, CCM_PLL5_CTRL_DDR_CLK); -#if defined(CONFIG_SUN4I) || defined(CONFIG_SUN7I) +#if defined(CONFIG_MACH_SUN4I) || defined(CONFIG_MACH_SUN7I) /* reset GPS */ clrbits_le32(&ccm->gps_clk_cfg, CCM_GPS_CTRL_RESET | CCM_GPS_CTRL_GATE); setbits_le32(&ccm->ahb_gate0, CCM_AHB_GATE_GPS); @@ -318,7 +318,7 @@ static void mctl_setup_dram_clock(u32 clk, u32 mbus_clk) /* PLL5P and PLL6 are the potential clock sources for MBUS */ pll6x_clk = clock_get_pll6() / 1000000; -#ifdef CONFIG_SUN7I +#ifdef CONFIG_MACH_SUN7I pll6x_clk *= 2; /* sun7i uses PLL6*2, sun5i uses just PLL6 */ #endif pll5p_clk = clock_get_pll5p() / 1000000; @@ -348,7 +348,7 @@ static void mctl_setup_dram_clock(u32 clk, u32 mbus_clk) * open DRAMC AHB & DLL register clock * close it first */ -#if defined(CONFIG_SUN5I) || defined(CONFIG_SUN7I) +#if defined(CONFIG_MACH_SUN5I) || defined(CONFIG_MACH_SUN7I) clrbits_le32(&ccm->ahb_gate0, CCM_AHB_GATE_SDRAM | CCM_AHB_GATE_DLL); #else clrbits_le32(&ccm->ahb_gate0, CCM_AHB_GATE_SDRAM); @@ -356,7 +356,7 @@ static void mctl_setup_dram_clock(u32 clk, u32 mbus_clk) udelay(22); /* then open it */ -#if defined(CONFIG_SUN5I) || defined(CONFIG_SUN7I) +#if defined(CONFIG_MACH_SUN5I) || defined(CONFIG_MACH_SUN7I) setbits_le32(&ccm->ahb_gate0, CCM_AHB_GATE_SDRAM | CCM_AHB_GATE_DLL); #else setbits_le32(&ccm->ahb_gate0, CCM_AHB_GATE_SDRAM); @@ -417,7 +417,7 @@ static int dramc_scan_readpipe(void) static void dramc_clock_output_en(u32 on) { -#if defined(CONFIG_SUN5I) || defined(CONFIG_SUN7I) +#if defined(CONFIG_MACH_SUN5I) || defined(CONFIG_MACH_SUN7I) struct sunxi_dram_reg *dram = (struct sunxi_dram_reg *)SUNXI_DRAMC_BASE; if (on) @@ -425,7 +425,7 @@ static void dramc_clock_output_en(u32 on) else clrbits_le32(&dram->mcr, DRAM_MCR_DCLK_OUT); #endif -#ifdef CONFIG_SUN4I +#ifdef CONFIG_MACH_SUN4I struct sunxi_ccm_reg *ccm = (struct sunxi_ccm_reg *)SUNXI_CCM_BASE; if (on) setbits_le32(&ccm->dram_clk_cfg, CCM_DRAM_CTRL_DCLK_OUT); @@ -527,7 +527,7 @@ static void mctl_set_impedance(u32 zq, u32 odt_en) u32 reg_val; u32 zprog = zq & 0xFF, zdata = (zq >> 8) & 0xFFFFF; -#ifndef CONFIG_SUN7I +#ifndef CONFIG_MACH_SUN7I /* Appears that some kind of automatically initiated default * ZQ calibration is already in progress at this point on sun4i/sun5i * hardware, but not on sun7i. So it is reasonable to wait for its @@ -539,7 +539,7 @@ static void mctl_set_impedance(u32 zq, u32 odt_en) if (!odt_en) return; -#ifdef CONFIG_SUN7I +#ifdef CONFIG_MACH_SUN7I /* Enabling ODT in SDR_IOCR on sun7i hardware results in a deadlock * unless bit 24 is set in SDR_ZQCR1. Not much is known about the * SDR_ZQCR1 register, but there are hints indicating that it might @@ -597,7 +597,7 @@ static unsigned long dramc_init_helper(struct dram_para *para) /* dram clock off */ dramc_clock_output_en(0); -#ifdef CONFIG_SUN4I +#ifdef CONFIG_MACH_SUN4I /* select dram controller 1 */ writel(DRAM_CSEL_MAGIC, &dram->csel); #endif @@ -654,7 +654,7 @@ static unsigned long dramc_init_helper(struct dram_para *para) writel(para->tpr2, &dram->tpr2); reg_val = DRAM_MR_BURST_LENGTH(0x0); -#if (defined(CONFIG_SUN5I) || defined(CONFIG_SUN7I)) +#if (defined(CONFIG_MACH_SUN5I) || defined(CONFIG_MACH_SUN7I)) reg_val |= DRAM_MR_POWER_DOWN; #endif reg_val |= DRAM_MR_CAS_LAT(para->cas - 4); @@ -668,7 +668,7 @@ static unsigned long dramc_init_helper(struct dram_para *para) /* disable drift compensation and set passive DQS window mode */ clrsetbits_le32(&dram->ccr, DRAM_CCR_DQS_DRIFT_COMP, DRAM_CCR_DQS_GATE); -#ifdef CONFIG_SUN7I +#ifdef CONFIG_MACH_SUN7I /* Command rate timing mode 2T & 1T */ if (para->tpr4 & 0x1) setbits_le32(&dram->ccr, DRAM_CCR_COMMAND_RATE_1T); @@ -718,7 +718,7 @@ unsigned long dramc_init(struct dram_para *para) /* try to autodetect the DRAM bus width and density */ para->io_width = 16; para->bus_width = 32; -#if defined(CONFIG_SUN4I) || defined(CONFIG_SUN5I) +#if defined(CONFIG_MACH_SUN4I) || defined(CONFIG_MACH_SUN5I) /* only A0-A14 address lines on A10/A13, limiting max density to 4096 */ para->density = 4096; #else diff --git a/arch/arm/cpu/armv7/sunxi/pinmux.c b/arch/arm/cpu/armv7/sunxi/pinmux.c index 1f2843fcac..b026f78ca5 100644 --- a/arch/arm/cpu/armv7/sunxi/pinmux.c +++ b/arch/arm/cpu/armv7/sunxi/pinmux.c @@ -10,32 +10,42 @@ #include <asm/io.h> #include <asm/arch/gpio.h> -int sunxi_gpio_set_cfgpin(u32 pin, u32 val) +void sunxi_gpio_set_cfgbank(struct sunxi_gpio *pio, int bank_offset, u32 val) { - u32 bank = GPIO_BANK(pin); - u32 index = GPIO_CFG_INDEX(pin); - u32 offset = GPIO_CFG_OFFSET(pin); - struct sunxi_gpio *pio = BANK_TO_GPIO(bank); + u32 index = GPIO_CFG_INDEX(bank_offset); + u32 offset = GPIO_CFG_OFFSET(bank_offset); clrsetbits_le32(&pio->cfg[0] + index, 0xf << offset, val << offset); - - return 0; } -int sunxi_gpio_get_cfgpin(u32 pin) +void sunxi_gpio_set_cfgpin(u32 pin, u32 val) { - u32 cfg; u32 bank = GPIO_BANK(pin); - u32 index = GPIO_CFG_INDEX(pin); - u32 offset = GPIO_CFG_OFFSET(pin); struct sunxi_gpio *pio = BANK_TO_GPIO(bank); + sunxi_gpio_set_cfgbank(pio, pin, val); +} + +int sunxi_gpio_get_cfgbank(struct sunxi_gpio *pio, int bank_offset) +{ + u32 index = GPIO_CFG_INDEX(bank_offset); + u32 offset = GPIO_CFG_OFFSET(bank_offset); + u32 cfg; + cfg = readl(&pio->cfg[0] + index); cfg >>= offset; return cfg & 0xf; } +int sunxi_gpio_get_cfgpin(u32 pin) +{ + u32 bank = GPIO_BANK(pin); + struct sunxi_gpio *pio = BANK_TO_GPIO(bank); + + return sunxi_gpio_get_cfgbank(pio, pin); +} + int sunxi_gpio_set_drv(u32 pin, u32 val) { u32 bank = GPIO_BANK(pin); diff --git a/arch/arm/cpu/armv7/uniphier/Kconfig b/arch/arm/cpu/armv7/uniphier/Kconfig index 524b193e58..36b7f11fbe 100644 --- a/arch/arm/cpu/armv7/uniphier/Kconfig +++ b/arch/arm/cpu/armv7/uniphier/Kconfig @@ -23,4 +23,40 @@ config MACH_PH1_SLD8 endchoice +config CMD_PINMON + bool "Enable boot mode pins monitor command" + depends on !SPL_BUILD + default y + help + The command "pinmon" shows the state of the boot mode pins. + The boot mode pins are latched when the system reset is deasserted + and determine which device the system should load a boot image from. + +config SOC_INIT + bool + default SPL_BUILD + +config DRAM_INIT + bool + default SPL_BUILD + +choice + prompt "DDR3 Frequency select" + depends on DRAM_INIT + +config DDR_FREQ_1600 + bool "DDR3 1600" + depends on MACH_PH1_PRO4 || MACH_PH1_LD4 + +config DDR_FREQ_1333 + bool "DDR3 1333" + depends on MACH_PH1_LD4 || MACH_PH1_SLD8 + +endchoice + +config DDR_FREQ + int + default 1333 if DDR_FREQ_1333 + default 1600 if DDR_FREQ_1600 + endmenu diff --git a/arch/arm/cpu/armv7/uniphier/Makefile b/arch/arm/cpu/armv7/uniphier/Makefile index 7cedddaadc..0f64d2591c 100644 --- a/arch/arm/cpu/armv7/uniphier/Makefile +++ b/arch/arm/cpu/armv7/uniphier/Makefile @@ -8,11 +8,12 @@ obj-$(CONFIG_SPL_BUILD) += spl.o obj-y += timer.o obj-y += reset.o obj-y += cache_uniphier.o +obj-$(CONFIG_BOARD_POSTCLK_INIT) += board_postclk_init.o obj-y += dram_init.o obj-$(CONFIG_DISPLAY_CPUINFO) += cpu_info.o obj-$(CONFIG_BOARD_LATE_INIT) += board_late_init.o obj-$(CONFIG_UNIPHIER_SMP) += smp.o -obj-$(if $(CONFIG_SPL_BUILD),,y) += cmd_pinmon.o +obj-$(CONFIG_CMD_PINMON) += cmd_pinmon.o obj-y += board_common.o obj-$(CONFIG_PFC_MICRO_SUPPORT_CARD) += support_card.o diff --git a/arch/arm/cpu/armv7/uniphier/ph1-ld4/board_postclk_init.c b/arch/arm/cpu/armv7/uniphier/board_postclk_init.c index 4302277dfc..89e44bb95b 100644 --- a/arch/arm/cpu/armv7/uniphier/ph1-ld4/board_postclk_init.c +++ b/arch/arm/cpu/armv7/uniphier/board_postclk_init.c @@ -5,11 +5,13 @@ * SPDX-License-Identifier: GPL-2.0+ */ -#include <common.h> +#include <linux/compiler.h> #include <asm/arch/led.h> #include <asm/arch/board.h> -void bcu_init(void); +void __weak bcu_init(void) +{ +}; void sbc_init(void); void sg_init(void); void pll_init(void); @@ -18,12 +20,15 @@ void clkrst_init(void); int board_postclk_init(void) { +#ifdef CONFIG_SOC_INIT bcu_init(); sbc_init(); sg_init(); + uniphier_board_reset(); + pll_init(); uniphier_board_init(); @@ -33,7 +38,7 @@ int board_postclk_init(void) clkrst_init(); led_write(B, 2, , ); - +#endif pin_init(); led_write(B, 3, , ); diff --git a/arch/arm/cpu/armv7/uniphier/dram_init.c b/arch/arm/cpu/armv7/uniphier/dram_init.c index 5465a0e6bf..7de657b7af 100644 --- a/arch/arm/cpu/armv7/uniphier/dram_init.c +++ b/arch/arm/cpu/armv7/uniphier/dram_init.c @@ -16,7 +16,7 @@ int dram_init(void) DECLARE_GLOBAL_DATA_PTR; gd->ram_size = CONFIG_SYS_SDRAM_SIZE; -#if !defined(CONFIG_SPL) || defined(CONFIG_SPL_BUILD) +#ifdef CONFIG_DRAM_INIT led_write(B, 4, , ); { diff --git a/arch/arm/cpu/armv7/uniphier/ph1-ld4/Makefile b/arch/arm/cpu/armv7/uniphier/ph1-ld4/Makefile index 781b511a97..fba1cc7498 100644 --- a/arch/arm/cpu/armv7/uniphier/ph1-ld4/Makefile +++ b/arch/arm/cpu/armv7/uniphier/ph1-ld4/Makefile @@ -5,7 +5,7 @@ obj-$(CONFIG_DISPLAY_BOARDINFO) += board_info.o obj-y += platdevice.o obj-y += boot-mode.o -obj-$(CONFIG_BOARD_POSTCLK_INIT) += board_postclk_init.o bcu_init.o \ - sbc_init.o sg_init.o pll_init.o clkrst_init.o pinctrl.o -obj-$(CONFIG_SPL_BUILD) += pll_spectrum.o \ - umc_init.o +obj-$(CONFIG_SOC_INIT) += bcu_init.o sbc_init.o sg_init.o pll_init.o \ + clkrst_init.o +obj-$(CONFIG_BOARD_POSTCLK_INIT) += pinctrl.o +obj-$(CONFIG_DRAM_INIT) += pll_spectrum.o umc_init.o diff --git a/arch/arm/cpu/armv7/uniphier/ph1-ld4/platdevice.c b/arch/arm/cpu/armv7/uniphier/ph1-ld4/platdevice.c index 0047223181..62f5b0148d 100644 --- a/arch/arm/cpu/armv7/uniphier/ph1-ld4/platdevice.c +++ b/arch/arm/cpu/armv7/uniphier/ph1-ld4/platdevice.c @@ -13,3 +13,16 @@ SERIAL_DEVICE(0, 0x54006800, UART_MASTER_CLK) SERIAL_DEVICE(1, 0x54006900, UART_MASTER_CLK) SERIAL_DEVICE(2, 0x54006a00, UART_MASTER_CLK) SERIAL_DEVICE(3, 0x54006b00, UART_MASTER_CLK) + +/* USB : TODO for Masahiro Yamada: move base address to Device Tree */ +struct uniphier_ehci_platform_data uniphier_ehci_platdata[] = { + { + .base = 0x5a800100, + }, + { + .base = 0x5a810100, + }, + { + .base = 0x5a820100, + }, +}; diff --git a/arch/arm/cpu/armv7/uniphier/ph1-ld4/umc_init.c b/arch/arm/cpu/armv7/uniphier/ph1-ld4/umc_init.c index 1344ac1caa..ebcbaabf65 100644 --- a/arch/arm/cpu/armv7/uniphier/ph1-ld4/umc_init.c +++ b/arch/arm/cpu/armv7/uniphier/ph1-ld4/umc_init.c @@ -149,10 +149,6 @@ int umc_init(void) CONFIG_SDRAM1_SIZE / 0x08000000); } -#if CONFIG_DDR_FREQ != 1333 && CONFIG_DDR_FREQ != 1600 -#error Unsupported DDR Frequency. -#endif - #if (CONFIG_SDRAM0_SIZE == 0x08000000 || CONFIG_SDRAM0_SIZE == 0x10000000) && \ (CONFIG_SDRAM1_SIZE == 0x08000000 || CONFIG_SDRAM1_SIZE == 0x10000000) && \ CONFIG_DDR_NUM_CH0 == 1 && CONFIG_DDR_NUM_CH1 == 1 diff --git a/arch/arm/cpu/armv7/uniphier/ph1-pro4/Makefile b/arch/arm/cpu/armv7/uniphier/ph1-pro4/Makefile index e11f4f6d8b..74129bc86a 100644 --- a/arch/arm/cpu/armv7/uniphier/ph1-pro4/Makefile +++ b/arch/arm/cpu/armv7/uniphier/ph1-pro4/Makefile @@ -5,7 +5,6 @@ obj-$(CONFIG_DISPLAY_BOARDINFO) += board_info.o obj-y += platdevice.o obj-y += boot-mode.o -obj-$(CONFIG_BOARD_POSTCLK_INIT) += board_postclk_init.o sbc_init.o \ - sg_init.o pll_init.o clkrst_init.o pinctrl.o -obj-$(CONFIG_SPL_BUILD) += pll_spectrum.o \ - umc_init.o +obj-$(CONFIG_SOC_INIT) += sbc_init.o sg_init.o pll_init.o clkrst_init.o +obj-$(CONFIG_BOARD_POSTCLK_INIT) += pinctrl.o +obj-$(CONFIG_DRAM_INIT) += pll_spectrum.o umc_init.o diff --git a/arch/arm/cpu/armv7/uniphier/ph1-pro4/board_postclk_init.c b/arch/arm/cpu/armv7/uniphier/ph1-pro4/board_postclk_init.c deleted file mode 100644 index 7198829988..0000000000 --- a/arch/arm/cpu/armv7/uniphier/ph1-pro4/board_postclk_init.c +++ /dev/null @@ -1,39 +0,0 @@ -/* - * Copyright (C) 2012-2014 Panasonic Corporation - * Author: Masahiro Yamada <yamada.m@jp.panasonic.com> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <asm/arch/led.h> -#include <asm/arch/board.h> - -void sbc_init(void); -void sg_init(void); -void pll_init(void); -void pin_init(void); -void clkrst_init(void); - -int board_postclk_init(void) -{ - sbc_init(); - - sg_init(); - - pll_init(); - - uniphier_board_init(); - - led_write(B, 1, , ); - - clkrst_init(); - - led_write(B, 2, , ); - - pin_init(); - - led_write(B, 3, , ); - - return 0; -} diff --git a/arch/arm/cpu/armv7/uniphier/ph1-pro4/pinctrl.c b/arch/arm/cpu/armv7/uniphier/ph1-pro4/pinctrl.c index 503c247d6b..4e3d47615b 100644 --- a/arch/arm/cpu/armv7/uniphier/ph1-pro4/pinctrl.c +++ b/arch/arm/cpu/armv7/uniphier/ph1-pro4/pinctrl.c @@ -41,5 +41,12 @@ void pin_init(void) sg_set_pinsel(54, 0); /* NRYBY0 -> NRYBY0 */ #endif +#ifdef CONFIG_USB_EHCI_UNIPHIER + sg_set_pinsel(184, 0); /* USB2VBUS -> USB2VBUS */ + sg_set_pinsel(185, 0); /* USB2OD -> USB2OD */ + sg_set_pinsel(187, 0); /* USB3VBUS -> USB3VBUS */ + sg_set_pinsel(188, 0); /* USB3OD -> USB3OD */ +#endif + writel(1, SG_LOADPINCTRL); } diff --git a/arch/arm/cpu/armv7/uniphier/ph1-pro4/platdevice.c b/arch/arm/cpu/armv7/uniphier/ph1-pro4/platdevice.c index 6da921e920..1843d0469f 100644 --- a/arch/arm/cpu/armv7/uniphier/ph1-pro4/platdevice.c +++ b/arch/arm/cpu/armv7/uniphier/ph1-pro4/platdevice.c @@ -13,3 +13,13 @@ SERIAL_DEVICE(0, 0x54006800, UART_MASTER_CLK) SERIAL_DEVICE(1, 0x54006900, UART_MASTER_CLK) SERIAL_DEVICE(2, 0x54006a00, UART_MASTER_CLK) SERIAL_DEVICE(3, 0x54006b00, UART_MASTER_CLK) + +/* USB : TODO for Masahiro Yamada: move base address to Device Tree */ +struct uniphier_ehci_platform_data uniphier_ehci_platdata[] = { + { + .base = 0x5a800100, + }, + { + .base = 0x5a810100, + }, +}; diff --git a/arch/arm/cpu/armv7/uniphier/ph1-pro4/umc_init.c b/arch/arm/cpu/armv7/uniphier/ph1-pro4/umc_init.c index dd462875bb..328b2f4d9a 100644 --- a/arch/arm/cpu/armv7/uniphier/ph1-pro4/umc_init.c +++ b/arch/arm/cpu/armv7/uniphier/ph1-pro4/umc_init.c @@ -122,10 +122,6 @@ int umc_init(void) CONFIG_SDRAM1_SIZE / 0x08000000); } -#if CONFIG_DDR_FREQ != 1600 -#error Unsupported DDR frequency. -#endif - #if ((CONFIG_SDRAM0_SIZE == 0x20000000 && CONFIG_DDR_NUM_CH0 == 2) || \ (CONFIG_SDRAM0_SIZE == 0x10000000 && CONFIG_DDR_NUM_CH0 == 1)) && \ ((CONFIG_SDRAM1_SIZE == 0x20000000 && CONFIG_DDR_NUM_CH1 == 2) || \ diff --git a/arch/arm/cpu/armv7/uniphier/ph1-sld8/Makefile b/arch/arm/cpu/armv7/uniphier/ph1-sld8/Makefile index 781b511a97..fba1cc7498 100644 --- a/arch/arm/cpu/armv7/uniphier/ph1-sld8/Makefile +++ b/arch/arm/cpu/armv7/uniphier/ph1-sld8/Makefile @@ -5,7 +5,7 @@ obj-$(CONFIG_DISPLAY_BOARDINFO) += board_info.o obj-y += platdevice.o obj-y += boot-mode.o -obj-$(CONFIG_BOARD_POSTCLK_INIT) += board_postclk_init.o bcu_init.o \ - sbc_init.o sg_init.o pll_init.o clkrst_init.o pinctrl.o -obj-$(CONFIG_SPL_BUILD) += pll_spectrum.o \ - umc_init.o +obj-$(CONFIG_SOC_INIT) += bcu_init.o sbc_init.o sg_init.o pll_init.o \ + clkrst_init.o +obj-$(CONFIG_BOARD_POSTCLK_INIT) += pinctrl.o +obj-$(CONFIG_DRAM_INIT) += pll_spectrum.o umc_init.o diff --git a/arch/arm/cpu/armv7/uniphier/ph1-sld8/board_postclk_init.c b/arch/arm/cpu/armv7/uniphier/ph1-sld8/board_postclk_init.c deleted file mode 100644 index 287b33c21d..0000000000 --- a/arch/arm/cpu/armv7/uniphier/ph1-sld8/board_postclk_init.c +++ /dev/null @@ -1 +0,0 @@ -#include "../ph1-ld4/board_postclk_init.c" diff --git a/arch/arm/cpu/armv7/uniphier/ph1-sld8/platdevice.c b/arch/arm/cpu/armv7/uniphier/ph1-sld8/platdevice.c index 59d054a310..72ec599f69 100644 --- a/arch/arm/cpu/armv7/uniphier/ph1-sld8/platdevice.c +++ b/arch/arm/cpu/armv7/uniphier/ph1-sld8/platdevice.c @@ -13,3 +13,16 @@ SERIAL_DEVICE(0, 0x54006800, UART_MASTER_CLK) SERIAL_DEVICE(1, 0x54006900, UART_MASTER_CLK) SERIAL_DEVICE(2, 0x54006a00, UART_MASTER_CLK) SERIAL_DEVICE(3, 0x54006b00, UART_MASTER_CLK) + +/* USB : TODO for Masahiro Yamada: move base address to Device Tree */ +struct uniphier_ehci_platform_data uniphier_ehci_platdata[] = { + { + .base = 0x5a800100, + }, + { + .base = 0x5a810100, + }, + { + .base = 0x5a820100, + }, +}; diff --git a/arch/arm/cpu/armv7/uniphier/ph1-sld8/umc_init.c b/arch/arm/cpu/armv7/uniphier/ph1-sld8/umc_init.c index ff2dcb1640..a44f999fbf 100644 --- a/arch/arm/cpu/armv7/uniphier/ph1-sld8/umc_init.c +++ b/arch/arm/cpu/armv7/uniphier/ph1-sld8/umc_init.c @@ -129,10 +129,6 @@ int umc_init(void) CONFIG_SDRAM1_SIZE / 0x08000000); } -#if CONFIG_DDR_FREQ != 1333 -#error Unsupported DDR frequency. -#endif - #if (CONFIG_SDRAM0_SIZE == 0x08000000 || CONFIG_SDRAM0_SIZE == 0x10000000) && \ (CONFIG_SDRAM1_SIZE == 0x08000000 || CONFIG_SDRAM1_SIZE == 0x10000000) && \ CONFIG_DDR_NUM_CH0 == 1 && CONFIG_DDR_NUM_CH1 == 1 diff --git a/arch/arm/cpu/armv7/uniphier/reset.c b/arch/arm/cpu/armv7/uniphier/reset.c index b0dc9673b4..50d1fed647 100644 --- a/arch/arm/cpu/armv7/uniphier/reset.c +++ b/arch/arm/cpu/armv7/uniphier/reset.c @@ -8,14 +8,11 @@ #include <common.h> #include <asm/io.h> #include <asm/arch/sc-regs.h> -#include <asm/arch/board.h> void reset_cpu(unsigned long ignored) { u32 tmp; - uniphier_board_reset(); - writel(5, SC_IRQTIMSET); /* default value */ tmp = readl(SC_SLFRSTSEL); diff --git a/arch/arm/cpu/armv7/zynq/ddrc.c b/arch/arm/cpu/armv7/zynq/ddrc.c index 1ea086d520..d74f8dbbc4 100644 --- a/arch/arm/cpu/armv7/zynq/ddrc.c +++ b/arch/arm/cpu/armv7/zynq/ddrc.c @@ -40,6 +40,7 @@ void zynq_ddrc_init(void) * first stage bootloader. To get ECC to work all memory has * been initialized by writing any value. */ + /* cppcheck-suppress nullPointer */ memset((void *)0, 0, 1 * 1024 * 1024); } else { puts("ECC disabled "); diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index d6d19167f6..b946abe7c3 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -1,3 +1,4 @@ +dtb-$(CONFIG_MACH_SUN7I) += sun7i-a20-pcduino3.dtb dtb-$(CONFIG_S5PC100) += s5pc1xx-smdkc100.dtb dtb-$(CONFIG_S5PC110) += s5pc1xx-goni.dtb dtb-$(CONFIG_EXYNOS4) += exynos4210-origen.dtb \ diff --git a/arch/arm/dts/sun7i-a20-pcduino3.dts b/arch/arm/dts/sun7i-a20-pcduino3.dts new file mode 100644 index 0000000000..f7cc8e7a09 --- /dev/null +++ b/arch/arm/dts/sun7i-a20-pcduino3.dts @@ -0,0 +1,177 @@ +/* + * Copyright 2014 Zoltan HERPAI + * Zoltan HERPAI <wigyori@uid0.hu> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +/include/ "sun7i-a20.dtsi" +/include/ "sunxi-common-regulators.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + +/ { + model = "LinkSprite pcDuino3"; + compatible = "linksprite,pcduino3", "allwinner,sun7i-a20"; + + chosen { + stdout-path = &uart0; + }; + + soc@01c00000 { + mmc0: mmc@01c0f000 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + cd-gpios = <&pio 7 1 0>; /* PH1 */ + cd-inverted; + status = "okay"; + }; + + usbphy: phy@01c13400 { + usb1_vbus-supply = <®_usb1_vbus>; + usb2_vbus-supply = <®_usb2_vbus>; + status = "okay"; + }; + + ehci0: usb@01c14000 { + status = "okay"; + }; + + ohci0: usb@01c14400 { + status = "okay"; + }; + + ahci: sata@01c18000 { + target-supply = <®_ahci_5v>; + status = "okay"; + }; + + ehci1: usb@01c1c000 { + status = "okay"; + }; + + ohci1: usb@01c1c400 { + status = "okay"; + }; + + pinctrl@01c20800 { + ahci_pwr_pin_a: ahci_pwr_pin@0 { + allwinner,pins = "PH2"; + }; + + led_pins_pcduino3: led_pins@0 { + allwinner,pins = "PH15", "PH16"; + allwinner,function = "gpio_out"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + key_pins_pcduino3: key_pins@0 { + allwinner,pins = "PH17", "PH18", "PH19"; + allwinner,function = "gpio_in"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + }; + + ir0: ir@01c21800 { + pinctrl-names = "default"; + pinctrl-0 = <&ir0_pins_a>; + status = "okay"; + }; + + uart0: serial@01c28000 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; + }; + + i2c0: i2c@01c2ac00 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; + + axp209: pmic@34 { + compatible = "x-powers,axp209"; + reg = <0x34>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 8>; + + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + gmac: ethernet@01c50000 { + pinctrl-names = "default"; + pinctrl-0 = <&gmac_pins_mii_a>; + phy = <&phy1>; + phy-mode = "mii"; + status = "okay"; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins_pcduino3>; + + tx { + label = "pcduino3:green:tx"; + gpios = <&pio 7 15 GPIO_ACTIVE_LOW>; + }; + + rx { + label = "pcduino3:green:rx"; + gpios = <&pio 7 16 GPIO_ACTIVE_LOW>; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&key_pins_pcduino3>; + #address-cells = <1>; + #size-cells = <0>; + button@0 { + label = "Key Back"; + linux,code = <KEY_BACK>; + gpios = <&pio 7 17 GPIO_ACTIVE_LOW>; + }; + button@1 { + label = "Key Home"; + linux,code = <KEY_HOME>; + gpios = <&pio 7 18 GPIO_ACTIVE_LOW>; + }; + button@2 { + label = "Key Menu"; + linux,code = <KEY_MENU>; + gpios = <&pio 7 19 GPIO_ACTIVE_LOW>; + }; + }; + + reg_usb1_vbus: usb1-vbus { + status = "okay"; + }; + + reg_usb2_vbus: usb2-vbus { + status = "okay"; + }; + + reg_ahci_5v: ahci-5v { + gpio = <&pio 7 2 0>; + status = "okay"; + }; +}; diff --git a/arch/arm/dts/sun7i-a20.dtsi b/arch/arm/dts/sun7i-a20.dtsi new file mode 100644 index 0000000000..4011628c73 --- /dev/null +++ b/arch/arm/dts/sun7i-a20.dtsi @@ -0,0 +1,988 @@ +/* + * Copyright 2013 Maxime Ripard + * + * Maxime Ripard <maxime.ripard@free-electrons.com> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/include/ "skeleton.dtsi" + +/ { + interrupt-parent = <&gic>; + + aliases { + ethernet0 = &gmac; + serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + serial3 = &uart3; + serial4 = &uart4; + serial5 = &uart5; + serial6 = &uart6; + serial7 = &uart7; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + compatible = "arm,cortex-a7"; + device_type = "cpu"; + reg = <0>; + }; + + cpu@1 { + compatible = "arm,cortex-a7"; + device_type = "cpu"; + reg = <1>; + }; + }; + + memory { + reg = <0x40000000 0x80000000>; + }; + + timer { + compatible = "arm,armv7-timer"; + interrupts = <1 13 0xf08>, + <1 14 0xf08>, + <1 11 0xf08>, + <1 10 0xf08>; + }; + + pmu { + compatible = "arm,cortex-a7-pmu", "arm,cortex-a15-pmu"; + interrupts = <0 120 4>, + <0 121 4>; + }; + + clocks { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + osc24M: clk@01c20050 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-osc-clk"; + reg = <0x01c20050 0x4>; + clock-frequency = <24000000>; + clock-output-names = "osc24M"; + }; + + osc32k: clk@0 { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <32768>; + clock-output-names = "osc32k"; + }; + + pll1: clk@01c20000 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-pll1-clk"; + reg = <0x01c20000 0x4>; + clocks = <&osc24M>; + clock-output-names = "pll1"; + }; + + pll4: clk@01c20018 { + #clock-cells = <0>; + compatible = "allwinner,sun7i-a20-pll4-clk"; + reg = <0x01c20018 0x4>; + clocks = <&osc24M>; + clock-output-names = "pll4"; + }; + + pll5: clk@01c20020 { + #clock-cells = <1>; + compatible = "allwinner,sun4i-a10-pll5-clk"; + reg = <0x01c20020 0x4>; + clocks = <&osc24M>; + clock-output-names = "pll5_ddr", "pll5_other"; + }; + + pll6: clk@01c20028 { + #clock-cells = <1>; + compatible = "allwinner,sun4i-a10-pll6-clk"; + reg = <0x01c20028 0x4>; + clocks = <&osc24M>; + clock-output-names = "pll6_sata", "pll6_other", "pll6"; + }; + + pll8: clk@01c20040 { + #clock-cells = <0>; + compatible = "allwinner,sun7i-a20-pll4-clk"; + reg = <0x01c20040 0x4>; + clocks = <&osc24M>; + clock-output-names = "pll8"; + }; + + cpu: cpu@01c20054 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-cpu-clk"; + reg = <0x01c20054 0x4>; + clocks = <&osc32k>, <&osc24M>, <&pll1>, <&pll6 1>; + clock-output-names = "cpu"; + }; + + axi: axi@01c20054 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-axi-clk"; + reg = <0x01c20054 0x4>; + clocks = <&cpu>; + clock-output-names = "axi"; + }; + + ahb: ahb@01c20054 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-ahb-clk"; + reg = <0x01c20054 0x4>; + clocks = <&axi>; + clock-output-names = "ahb"; + }; + + ahb_gates: clk@01c20060 { + #clock-cells = <1>; + compatible = "allwinner,sun7i-a20-ahb-gates-clk"; + reg = <0x01c20060 0x8>; + clocks = <&ahb>; + clock-output-names = "ahb_usb0", "ahb_ehci0", + "ahb_ohci0", "ahb_ehci1", "ahb_ohci1", + "ahb_ss", "ahb_dma", "ahb_bist", "ahb_mmc0", + "ahb_mmc1", "ahb_mmc2", "ahb_mmc3", "ahb_ms", + "ahb_nand", "ahb_sdram", "ahb_ace", + "ahb_emac", "ahb_ts", "ahb_spi0", "ahb_spi1", + "ahb_spi2", "ahb_spi3", "ahb_sata", + "ahb_hstimer", "ahb_ve", "ahb_tvd", "ahb_tve0", + "ahb_tve1", "ahb_lcd0", "ahb_lcd1", "ahb_csi0", + "ahb_csi1", "ahb_hdmi1", "ahb_hdmi0", + "ahb_de_be0", "ahb_de_be1", "ahb_de_fe0", + "ahb_de_fe1", "ahb_gmac", "ahb_mp", + "ahb_mali"; + }; + + apb0: apb0@01c20054 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-apb0-clk"; + reg = <0x01c20054 0x4>; + clocks = <&ahb>; + clock-output-names = "apb0"; + }; + + apb0_gates: clk@01c20068 { + #clock-cells = <1>; + compatible = "allwinner,sun7i-a20-apb0-gates-clk"; + reg = <0x01c20068 0x4>; + clocks = <&apb0>; + clock-output-names = "apb0_codec", "apb0_spdif", + "apb0_ac97", "apb0_iis0", "apb0_iis1", + "apb0_pio", "apb0_ir0", "apb0_ir1", + "apb0_iis2", "apb0_keypad"; + }; + + apb1_mux: apb1_mux@01c20058 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-apb1-mux-clk"; + reg = <0x01c20058 0x4>; + clocks = <&osc24M>, <&pll6 1>, <&osc32k>; + clock-output-names = "apb1_mux"; + }; + + apb1: apb1@01c20058 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-apb1-clk"; + reg = <0x01c20058 0x4>; + clocks = <&apb1_mux>; + clock-output-names = "apb1"; + }; + + apb1_gates: clk@01c2006c { + #clock-cells = <1>; + compatible = "allwinner,sun7i-a20-apb1-gates-clk"; + reg = <0x01c2006c 0x4>; + clocks = <&apb1>; + clock-output-names = "apb1_i2c0", "apb1_i2c1", + "apb1_i2c2", "apb1_i2c3", "apb1_can", + "apb1_scr", "apb1_ps20", "apb1_ps21", + "apb1_i2c4", "apb1_uart0", "apb1_uart1", + "apb1_uart2", "apb1_uart3", "apb1_uart4", + "apb1_uart5", "apb1_uart6", "apb1_uart7"; + }; + + nand_clk: clk@01c20080 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-mod0-clk"; + reg = <0x01c20080 0x4>; + clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; + clock-output-names = "nand"; + }; + + ms_clk: clk@01c20084 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-mod0-clk"; + reg = <0x01c20084 0x4>; + clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; + clock-output-names = "ms"; + }; + + mmc0_clk: clk@01c20088 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-mod0-clk"; + reg = <0x01c20088 0x4>; + clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; + clock-output-names = "mmc0"; + }; + + mmc1_clk: clk@01c2008c { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-mod0-clk"; + reg = <0x01c2008c 0x4>; + clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; + clock-output-names = "mmc1"; + }; + + mmc2_clk: clk@01c20090 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-mod0-clk"; + reg = <0x01c20090 0x4>; + clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; + clock-output-names = "mmc2"; + }; + + mmc3_clk: clk@01c20094 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-mod0-clk"; + reg = <0x01c20094 0x4>; + clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; + clock-output-names = "mmc3"; + }; + + ts_clk: clk@01c20098 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-mod0-clk"; + reg = <0x01c20098 0x4>; + clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; + clock-output-names = "ts"; + }; + + ss_clk: clk@01c2009c { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-mod0-clk"; + reg = <0x01c2009c 0x4>; + clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; + clock-output-names = "ss"; + }; + + spi0_clk: clk@01c200a0 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-mod0-clk"; + reg = <0x01c200a0 0x4>; + clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; + clock-output-names = "spi0"; + }; + + spi1_clk: clk@01c200a4 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-mod0-clk"; + reg = <0x01c200a4 0x4>; + clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; + clock-output-names = "spi1"; + }; + + spi2_clk: clk@01c200a8 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-mod0-clk"; + reg = <0x01c200a8 0x4>; + clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; + clock-output-names = "spi2"; + }; + + pata_clk: clk@01c200ac { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-mod0-clk"; + reg = <0x01c200ac 0x4>; + clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; + clock-output-names = "pata"; + }; + + ir0_clk: clk@01c200b0 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-mod0-clk"; + reg = <0x01c200b0 0x4>; + clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; + clock-output-names = "ir0"; + }; + + ir1_clk: clk@01c200b4 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-mod0-clk"; + reg = <0x01c200b4 0x4>; + clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; + clock-output-names = "ir1"; + }; + + usb_clk: clk@01c200cc { + #clock-cells = <1>; + #reset-cells = <1>; + compatible = "allwinner,sun4i-a10-usb-clk"; + reg = <0x01c200cc 0x4>; + clocks = <&pll6 1>; + clock-output-names = "usb_ohci0", "usb_ohci1", "usb_phy"; + }; + + spi3_clk: clk@01c200d4 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-mod0-clk"; + reg = <0x01c200d4 0x4>; + clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; + clock-output-names = "spi3"; + }; + + mbus_clk: clk@01c2015c { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-mod0-clk"; + reg = <0x01c2015c 0x4>; + clocks = <&osc24M>, <&pll6 2>, <&pll5 1>; + clock-output-names = "mbus"; + }; + + /* + * The following two are dummy clocks, placeholders used in the gmac_tx + * clock. The gmac driver will choose one parent depending on the PHY + * interface mode, using clk_set_rate auto-reparenting. + * The actual TX clock rate is not controlled by the gmac_tx clock. + */ + mii_phy_tx_clk: clk@2 { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <25000000>; + clock-output-names = "mii_phy_tx"; + }; + + gmac_int_tx_clk: clk@3 { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <125000000>; + clock-output-names = "gmac_int_tx"; + }; + + gmac_tx_clk: clk@01c20164 { + #clock-cells = <0>; + compatible = "allwinner,sun7i-a20-gmac-clk"; + reg = <0x01c20164 0x4>; + clocks = <&mii_phy_tx_clk>, <&gmac_int_tx_clk>; + clock-output-names = "gmac_tx"; + }; + + /* + * Dummy clock used by output clocks + */ + osc24M_32k: clk@1 { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clock-div = <750>; + clock-mult = <1>; + clocks = <&osc24M>; + clock-output-names = "osc24M_32k"; + }; + + clk_out_a: clk@01c201f0 { + #clock-cells = <0>; + compatible = "allwinner,sun7i-a20-out-clk"; + reg = <0x01c201f0 0x4>; + clocks = <&osc24M_32k>, <&osc32k>, <&osc24M>; + clock-output-names = "clk_out_a"; + }; + + clk_out_b: clk@01c201f4 { + #clock-cells = <0>; + compatible = "allwinner,sun7i-a20-out-clk"; + reg = <0x01c201f4 0x4>; + clocks = <&osc24M_32k>, <&osc32k>, <&osc24M>; + clock-output-names = "clk_out_b"; + }; + }; + + soc@01c00000 { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + nmi_intc: interrupt-controller@01c00030 { + compatible = "allwinner,sun7i-a20-sc-nmi"; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0x01c00030 0x0c>; + interrupts = <0 0 4>; + }; + + spi0: spi@01c05000 { + compatible = "allwinner,sun4i-a10-spi"; + reg = <0x01c05000 0x1000>; + interrupts = <0 10 4>; + clocks = <&ahb_gates 20>, <&spi0_clk>; + clock-names = "ahb", "mod"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + spi1: spi@01c06000 { + compatible = "allwinner,sun4i-a10-spi"; + reg = <0x01c06000 0x1000>; + interrupts = <0 11 4>; + clocks = <&ahb_gates 21>, <&spi1_clk>; + clock-names = "ahb", "mod"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + emac: ethernet@01c0b000 { + compatible = "allwinner,sun4i-a10-emac"; + reg = <0x01c0b000 0x1000>; + interrupts = <0 55 4>; + clocks = <&ahb_gates 17>; + status = "disabled"; + }; + + mdio@01c0b080 { + compatible = "allwinner,sun4i-a10-mdio"; + reg = <0x01c0b080 0x14>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + mmc0: mmc@01c0f000 { + compatible = "allwinner,sun5i-a13-mmc"; + reg = <0x01c0f000 0x1000>; + clocks = <&ahb_gates 8>, <&mmc0_clk>; + clock-names = "ahb", "mmc"; + interrupts = <0 32 4>; + status = "disabled"; + }; + + mmc1: mmc@01c10000 { + compatible = "allwinner,sun5i-a13-mmc"; + reg = <0x01c10000 0x1000>; + clocks = <&ahb_gates 9>, <&mmc1_clk>; + clock-names = "ahb", "mmc"; + interrupts = <0 33 4>; + status = "disabled"; + }; + + mmc2: mmc@01c11000 { + compatible = "allwinner,sun5i-a13-mmc"; + reg = <0x01c11000 0x1000>; + clocks = <&ahb_gates 10>, <&mmc2_clk>; + clock-names = "ahb", "mmc"; + interrupts = <0 34 4>; + status = "disabled"; + }; + + mmc3: mmc@01c12000 { + compatible = "allwinner,sun5i-a13-mmc"; + reg = <0x01c12000 0x1000>; + clocks = <&ahb_gates 11>, <&mmc3_clk>; + clock-names = "ahb", "mmc"; + interrupts = <0 35 4>; + status = "disabled"; + }; + + usbphy: phy@01c13400 { + #phy-cells = <1>; + compatible = "allwinner,sun7i-a20-usb-phy"; + reg = <0x01c13400 0x10 0x01c14800 0x4 0x01c1c800 0x4>; + reg-names = "phy_ctrl", "pmu1", "pmu2"; + clocks = <&usb_clk 8>; + clock-names = "usb_phy"; + resets = <&usb_clk 1>, <&usb_clk 2>; + reset-names = "usb1_reset", "usb2_reset"; + status = "disabled"; + }; + + ehci0: usb@01c14000 { + compatible = "allwinner,sun7i-a20-ehci", "generic-ehci"; + reg = <0x01c14000 0x100>; + interrupts = <0 39 4>; + clocks = <&ahb_gates 1>; + phys = <&usbphy 1>; + phy-names = "usb"; + status = "disabled"; + }; + + ohci0: usb@01c14400 { + compatible = "allwinner,sun7i-a20-ohci", "generic-ohci"; + reg = <0x01c14400 0x100>; + interrupts = <0 64 4>; + clocks = <&usb_clk 6>, <&ahb_gates 2>; + phys = <&usbphy 1>; + phy-names = "usb"; + status = "disabled"; + }; + + spi2: spi@01c17000 { + compatible = "allwinner,sun4i-a10-spi"; + reg = <0x01c17000 0x1000>; + interrupts = <0 12 4>; + clocks = <&ahb_gates 22>, <&spi2_clk>; + clock-names = "ahb", "mod"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + ahci: sata@01c18000 { + compatible = "allwinner,sun4i-a10-ahci"; + reg = <0x01c18000 0x1000>; + interrupts = <0 56 4>; + clocks = <&pll6 0>, <&ahb_gates 25>; + status = "disabled"; + }; + + ehci1: usb@01c1c000 { + compatible = "allwinner,sun7i-a20-ehci", "generic-ehci"; + reg = <0x01c1c000 0x100>; + interrupts = <0 40 4>; + clocks = <&ahb_gates 3>; + phys = <&usbphy 2>; + phy-names = "usb"; + status = "disabled"; + }; + + ohci1: usb@01c1c400 { + compatible = "allwinner,sun7i-a20-ohci", "generic-ohci"; + reg = <0x01c1c400 0x100>; + interrupts = <0 65 4>; + clocks = <&usb_clk 7>, <&ahb_gates 4>; + phys = <&usbphy 2>; + phy-names = "usb"; + status = "disabled"; + }; + + spi3: spi@01c1f000 { + compatible = "allwinner,sun4i-a10-spi"; + reg = <0x01c1f000 0x1000>; + interrupts = <0 50 4>; + clocks = <&ahb_gates 23>, <&spi3_clk>; + clock-names = "ahb", "mod"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + pio: pinctrl@01c20800 { + compatible = "allwinner,sun7i-a20-pinctrl"; + reg = <0x01c20800 0x400>; + interrupts = <0 28 4>; + clocks = <&apb0_gates 5>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + #size-cells = <0>; + #gpio-cells = <3>; + + pwm0_pins_a: pwm0@0 { + allwinner,pins = "PB2"; + allwinner,function = "pwm"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + pwm1_pins_a: pwm1@0 { + allwinner,pins = "PI3"; + allwinner,function = "pwm"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + uart0_pins_a: uart0@0 { + allwinner,pins = "PB22", "PB23"; + allwinner,function = "uart0"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + uart2_pins_a: uart2@0 { + allwinner,pins = "PI16", "PI17", "PI18", "PI19"; + allwinner,function = "uart2"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + uart6_pins_a: uart6@0 { + allwinner,pins = "PI12", "PI13"; + allwinner,function = "uart6"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + uart7_pins_a: uart7@0 { + allwinner,pins = "PI20", "PI21"; + allwinner,function = "uart7"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + i2c0_pins_a: i2c0@0 { + allwinner,pins = "PB0", "PB1"; + allwinner,function = "i2c0"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + i2c1_pins_a: i2c1@0 { + allwinner,pins = "PB18", "PB19"; + allwinner,function = "i2c1"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + i2c2_pins_a: i2c2@0 { + allwinner,pins = "PB20", "PB21"; + allwinner,function = "i2c2"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + emac_pins_a: emac0@0 { + allwinner,pins = "PA0", "PA1", "PA2", + "PA3", "PA4", "PA5", "PA6", + "PA7", "PA8", "PA9", "PA10", + "PA11", "PA12", "PA13", "PA14", + "PA15", "PA16"; + allwinner,function = "emac"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + clk_out_a_pins_a: clk_out_a@0 { + allwinner,pins = "PI12"; + allwinner,function = "clk_out_a"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + clk_out_b_pins_a: clk_out_b@0 { + allwinner,pins = "PI13"; + allwinner,function = "clk_out_b"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + gmac_pins_mii_a: gmac_mii@0 { + allwinner,pins = "PA0", "PA1", "PA2", + "PA3", "PA4", "PA5", "PA6", + "PA7", "PA8", "PA9", "PA10", + "PA11", "PA12", "PA13", "PA14", + "PA15", "PA16"; + allwinner,function = "gmac"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + gmac_pins_rgmii_a: gmac_rgmii@0 { + allwinner,pins = "PA0", "PA1", "PA2", + "PA3", "PA4", "PA5", "PA6", + "PA7", "PA8", "PA10", + "PA11", "PA12", "PA13", + "PA15", "PA16"; + allwinner,function = "gmac"; + /* + * data lines in RGMII mode use DDR mode + * and need a higher signal drive strength + */ + allwinner,drive = <3>; + allwinner,pull = <0>; + }; + + spi1_pins_a: spi1@0 { + allwinner,pins = "PI16", "PI17", "PI18", "PI19"; + allwinner,function = "spi1"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + spi2_pins_a: spi2@0 { + allwinner,pins = "PC19", "PC20", "PC21", "PC22"; + allwinner,function = "spi2"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + mmc0_pins_a: mmc0@0 { + allwinner,pins = "PF0","PF1","PF2","PF3","PF4","PF5"; + allwinner,function = "mmc0"; + allwinner,drive = <2>; + allwinner,pull = <0>; + }; + + mmc0_cd_pin_reference_design: mmc0_cd_pin@0 { + allwinner,pins = "PH1"; + allwinner,function = "gpio_in"; + allwinner,drive = <0>; + allwinner,pull = <1>; + }; + + mmc3_pins_a: mmc3@0 { + allwinner,pins = "PI4","PI5","PI6","PI7","PI8","PI9"; + allwinner,function = "mmc3"; + allwinner,drive = <2>; + allwinner,pull = <0>; + }; + + ir0_pins_a: ir0@0 { + allwinner,pins = "PB3","PB4"; + allwinner,function = "ir0"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + ir1_pins_a: ir1@0 { + allwinner,pins = "PB22","PB23"; + allwinner,function = "ir1"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + }; + + timer@01c20c00 { + compatible = "allwinner,sun4i-a10-timer"; + reg = <0x01c20c00 0x90>; + interrupts = <0 22 4>, + <0 23 4>, + <0 24 4>, + <0 25 4>, + <0 67 4>, + <0 68 4>; + clocks = <&osc24M>; + }; + + wdt: watchdog@01c20c90 { + compatible = "allwinner,sun4i-a10-wdt"; + reg = <0x01c20c90 0x10>; + }; + + rtc: rtc@01c20d00 { + compatible = "allwinner,sun7i-a20-rtc"; + reg = <0x01c20d00 0x20>; + interrupts = <0 24 4>; + }; + + pwm: pwm@01c20e00 { + compatible = "allwinner,sun7i-a20-pwm"; + reg = <0x01c20e00 0xc>; + clocks = <&osc24M>; + #pwm-cells = <3>; + status = "disabled"; + }; + + ir0: ir@01c21800 { + compatible = "allwinner,sun4i-a10-ir"; + clocks = <&apb0_gates 6>, <&ir0_clk>; + clock-names = "apb", "ir"; + interrupts = <0 5 4>; + reg = <0x01c21800 0x40>; + status = "disabled"; + }; + + ir1: ir@01c21c00 { + compatible = "allwinner,sun4i-a10-ir"; + clocks = <&apb0_gates 7>, <&ir1_clk>; + clock-names = "apb", "ir"; + interrupts = <0 6 4>; + reg = <0x01c21c00 0x40>; + status = "disabled"; + }; + + sid: eeprom@01c23800 { + compatible = "allwinner,sun7i-a20-sid"; + reg = <0x01c23800 0x200>; + }; + + rtp: rtp@01c25000 { + compatible = "allwinner,sun4i-a10-ts"; + reg = <0x01c25000 0x100>; + interrupts = <0 29 4>; + }; + + uart0: serial@01c28000 { + compatible = "snps,dw-apb-uart"; + reg = <0x01c28000 0x400>; + interrupts = <0 1 4>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&apb1_gates 16>; + status = "disabled"; + }; + + uart1: serial@01c28400 { + compatible = "snps,dw-apb-uart"; + reg = <0x01c28400 0x400>; + interrupts = <0 2 4>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&apb1_gates 17>; + status = "disabled"; + }; + + uart2: serial@01c28800 { + compatible = "snps,dw-apb-uart"; + reg = <0x01c28800 0x400>; + interrupts = <0 3 4>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&apb1_gates 18>; + status = "disabled"; + }; + + uart3: serial@01c28c00 { + compatible = "snps,dw-apb-uart"; + reg = <0x01c28c00 0x400>; + interrupts = <0 4 4>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&apb1_gates 19>; + status = "disabled"; + }; + + uart4: serial@01c29000 { + compatible = "snps,dw-apb-uart"; + reg = <0x01c29000 0x400>; + interrupts = <0 17 4>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&apb1_gates 20>; + status = "disabled"; + }; + + uart5: serial@01c29400 { + compatible = "snps,dw-apb-uart"; + reg = <0x01c29400 0x400>; + interrupts = <0 18 4>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&apb1_gates 21>; + status = "disabled"; + }; + + uart6: serial@01c29800 { + compatible = "snps,dw-apb-uart"; + reg = <0x01c29800 0x400>; + interrupts = <0 19 4>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&apb1_gates 22>; + status = "disabled"; + }; + + uart7: serial@01c29c00 { + compatible = "snps,dw-apb-uart"; + reg = <0x01c29c00 0x400>; + interrupts = <0 20 4>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&apb1_gates 23>; + status = "disabled"; + }; + + i2c0: i2c@01c2ac00 { + compatible = "allwinner,sun7i-a20-i2c", "allwinner,sun4i-a10-i2c"; + reg = <0x01c2ac00 0x400>; + interrupts = <0 7 4>; + clocks = <&apb1_gates 0>; + clock-frequency = <100000>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c1: i2c@01c2b000 { + compatible = "allwinner,sun7i-a20-i2c", "allwinner,sun4i-a10-i2c"; + reg = <0x01c2b000 0x400>; + interrupts = <0 8 4>; + clocks = <&apb1_gates 1>; + clock-frequency = <100000>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c2: i2c@01c2b400 { + compatible = "allwinner,sun7i-a20-i2c", "allwinner,sun4i-a10-i2c"; + reg = <0x01c2b400 0x400>; + interrupts = <0 9 4>; + clocks = <&apb1_gates 2>; + clock-frequency = <100000>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c3: i2c@01c2b800 { + compatible = "allwinner,sun7i-a20-i2c", "allwinner,sun4i-a10-i2c"; + reg = <0x01c2b800 0x400>; + interrupts = <0 88 4>; + clocks = <&apb1_gates 3>; + clock-frequency = <100000>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c4: i2c@01c2c000 { + compatible = "allwinner,sun7i-a20-i2c", "allwinner,sun4i-a10-i2c"; + reg = <0x01c2c000 0x400>; + interrupts = <0 89 4>; + clocks = <&apb1_gates 15>; + clock-frequency = <100000>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + gmac: ethernet@01c50000 { + compatible = "allwinner,sun7i-a20-gmac"; + reg = <0x01c50000 0x10000>; + interrupts = <0 85 4>; + interrupt-names = "macirq"; + clocks = <&ahb_gates 49>, <&gmac_tx_clk>; + clock-names = "stmmaceth", "allwinner_gmac_tx"; + snps,pbl = <2>; + snps,fixed-burst; + snps,force_sf_dma_mode; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + hstimer@01c60000 { + compatible = "allwinner,sun7i-a20-hstimer"; + reg = <0x01c60000 0x1000>; + interrupts = <0 81 4>, + <0 82 4>, + <0 83 4>, + <0 84 4>; + clocks = <&ahb_gates 28>; + }; + + gic: interrupt-controller@01c81000 { + compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic"; + reg = <0x01c81000 0x1000>, + <0x01c82000 0x1000>, + <0x01c84000 0x2000>, + <0x01c86000 0x2000>; + interrupt-controller; + #interrupt-cells = <3>; + interrupts = <1 9 0xf04>; + }; + }; +}; diff --git a/arch/arm/dts/sunxi-common-regulators.dtsi b/arch/arm/dts/sunxi-common-regulators.dtsi new file mode 100644 index 0000000000..3d021efd1a --- /dev/null +++ b/arch/arm/dts/sunxi-common-regulators.dtsi @@ -0,0 +1,89 @@ +/* + * sunxi boards common regulator (ahci target power supply, usb-vbus) code + * + * Copyright 2014 - Hans de Goede <hdegoede@redhat.com> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/ { + soc@01c00000 { + pio: pinctrl@01c20800 { + ahci_pwr_pin_a: ahci_pwr_pin@0 { + allwinner,pins = "PB8"; + allwinner,function = "gpio_out"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + usb1_vbus_pin_a: usb1_vbus_pin@0 { + allwinner,pins = "PH6"; + allwinner,function = "gpio_out"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + usb2_vbus_pin_a: usb2_vbus_pin@0 { + allwinner,pins = "PH3"; + allwinner,function = "gpio_out"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + }; + }; + + reg_ahci_5v: ahci-5v { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&ahci_pwr_pin_a>; + regulator-name = "ahci-5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + gpio = <&pio 1 8 0>; + status = "disabled"; + }; + + reg_usb1_vbus: usb1-vbus { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&usb1_vbus_pin_a>; + regulator-name = "usb1-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + gpio = <&pio 7 6 0>; + status = "disabled"; + }; + + reg_usb2_vbus: usb2-vbus { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&usb2_vbus_pin_a>; + regulator-name = "usb2-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + gpio = <&pio 7 3 0>; + status = "disabled"; + }; + + reg_vcc3v0: vcc3v0 { + compatible = "regulator-fixed"; + regulator-name = "vcc3v0"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + }; + + reg_vcc3v3: vcc3v3 { + compatible = "regulator-fixed"; + regulator-name = "vcc3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; +}; diff --git a/arch/arm/imx-common/iomux-v3.c b/arch/arm/imx-common/iomux-v3.c index 22cd11aa04..e88e6e2a98 100644 --- a/arch/arm/imx-common/iomux-v3.c +++ b/arch/arm/imx-common/iomux-v3.c @@ -77,3 +77,18 @@ void imx_iomux_v3_setup_multiple_pads(iomux_v3_cfg_t const *pad_list, p += stride; } } + +void imx_iomux_set_gpr_register(int group, int start_bit, + int num_bits, int value) +{ + int i = 0; + u32 reg; + reg = readl(base + group * 4); + while (num_bits) { + reg &= ~(1<<(start_bit + i)); + i++; + num_bits--; + } + reg |= (value << start_bit); + writel(reg, base + group * 4); +} diff --git a/arch/arm/imx-common/timer.c b/arch/arm/imx-common/timer.c index c63f78f682..65ef60bf2e 100644 --- a/arch/arm/imx-common/timer.c +++ b/arch/arm/imx-common/timer.c @@ -12,6 +12,7 @@ #include <div64.h> #include <asm/arch/imx-regs.h> #include <asm/arch/clock.h> +#include <asm/arch/sys_proto.h> /* General purpose timers registers */ struct mxc_gpt { @@ -26,23 +27,59 @@ static struct mxc_gpt *cur_gpt = (struct mxc_gpt *)GPT1_BASE_ADDR; /* General purpose timers bitfields */ #define GPTCR_SWR (1 << 15) /* Software reset */ +#define GPTCR_24MEN (1 << 10) /* Enable 24MHz clock input */ #define GPTCR_FRR (1 << 9) /* Freerun / restart */ -#define GPTCR_CLKSOURCE_32 (4 << 6) /* Clock source */ +#define GPTCR_CLKSOURCE_32 (4 << 6) /* Clock source 32khz */ +#define GPTCR_CLKSOURCE_OSC (5 << 6) /* Clock source OSC */ +#define GPTCR_CLKSOURCE_PRE (1 << 6) /* Clock source PRECLK */ +#define GPTCR_CLKSOURCE_MASK (0x7 << 6) #define GPTCR_TEN 1 /* Timer enable */ +#define GPTPR_PRESCALER24M_SHIFT 12 +#define GPTPR_PRESCALER24M_MASK (0xF << GPTPR_PRESCALER24M_SHIFT) + DECLARE_GLOBAL_DATA_PTR; +static inline int gpt_has_clk_source_osc(void) +{ +#if defined(CONFIG_MX6) + if (((is_cpu_type(MXC_CPU_MX6Q) || is_cpu_type(MXC_CPU_MX6D)) && + (is_soc_rev(CHIP_REV_1_0) > 0)) || is_cpu_type(MXC_CPU_MX6DL) || + is_cpu_type(MXC_CPU_MX6SOLO) || is_cpu_type(MXC_CPU_MX6SX)) + return 1; + + return 0; +#else + return 0; +#endif +} + +static inline ulong gpt_get_clk(void) +{ +#ifdef CONFIG_MXC_GPT_HCLK + if (gpt_has_clk_source_osc()) + return MXC_HCLK >> 3; + else + return mxc_get_clock(MXC_IPG_PERCLK); +#else + return MXC_CLK32; +#endif +} static inline unsigned long long tick_to_time(unsigned long long tick) { + ulong gpt_clk = gpt_get_clk(); + tick *= CONFIG_SYS_HZ; - do_div(tick, MXC_CLK32); + do_div(tick, gpt_clk); return tick; } static inline unsigned long long us_to_tick(unsigned long long usec) { - usec = usec * MXC_CLK32 + 999999; + ulong gpt_clk = gpt_get_clk(); + + usec = usec * gpt_clk + 999999; do_div(usec, 1000000); return usec; @@ -59,11 +96,31 @@ int timer_init(void) for (i = 0; i < 100; i++) __raw_writel(0, &cur_gpt->control); - __raw_writel(0, &cur_gpt->prescaler); /* 32Khz */ - - /* Freerun Mode, PERCLK1 input */ i = __raw_readl(&cur_gpt->control); - __raw_writel(i | GPTCR_CLKSOURCE_32 | GPTCR_TEN, &cur_gpt->control); + i &= ~GPTCR_CLKSOURCE_MASK; + +#ifdef CONFIG_MXC_GPT_HCLK + if (gpt_has_clk_source_osc()) { + i |= GPTCR_CLKSOURCE_OSC | GPTCR_TEN; + + /* For DL/S, SX, set 24Mhz OSC Enable bit and prescaler */ + if (is_cpu_type(MXC_CPU_MX6DL) || + is_cpu_type(MXC_CPU_MX6SOLO) || + is_cpu_type(MXC_CPU_MX6SX)) { + i |= GPTCR_24MEN; + + /* Produce 3Mhz clock */ + __raw_writel((7 << GPTPR_PRESCALER24M_SHIFT), + &cur_gpt->prescaler); + } + } else { + i |= GPTCR_CLKSOURCE_PRE | GPTCR_TEN; + } +#else + __raw_writel(0, &cur_gpt->prescaler); /* 32Khz */ + i |= GPTCR_CLKSOURCE_32 | GPTCR_TEN; +#endif + __raw_writel(i, &cur_gpt->control); gd->arch.tbl = __raw_readl(&cur_gpt->counter); gd->arch.tbu = 0; @@ -86,7 +143,7 @@ ulong get_timer_masked(void) { /* * get_ticks() returns a long long (64 bit), it wraps in - * 2^64 / MXC_CLK32 = 2^64 / 2^15 = 2^49 ~ 5 * 10^14 (s) ~ + * 2^64 / GPT_CLK = 2^64 / 2^15 = 2^49 ~ 5 * 10^14 (s) ~ * 5 * 10^9 days... and get_ticks() * CONFIG_SYS_HZ wraps in * 5 * 10^6 days - long enough. */ @@ -117,5 +174,5 @@ void __udelay(unsigned long usec) */ ulong get_tbclk(void) { - return MXC_CLK32; + return gpt_get_clk(); } diff --git a/arch/arm/include/asm/arch-am33xx/sys_proto.h b/arch/arm/include/asm/arch-am33xx/sys_proto.h index 33a82fca98..7eacf27a93 100644 --- a/arch/arm/include/asm/arch-am33xx/sys_proto.h +++ b/arch/arm/include/asm/arch-am33xx/sys_proto.h @@ -14,8 +14,6 @@ #include <asm/ti-common/sys_proto.h> #include <asm/arch/cpu.h> -#define BOARD_REV_ID 0x0 - u32 get_cpu_rev(void); u32 get_sysboot_value(void); diff --git a/arch/arm/include/asm/arch-at91/at91_shdwn.h b/arch/arm/include/asm/arch-at91/at91_shdwn.h deleted file mode 100644 index 18d9ea690e..0000000000 --- a/arch/arm/include/asm/arch-at91/at91_shdwn.h +++ /dev/null @@ -1,35 +0,0 @@ -/* - * Copyright (C) 2010 - * Reinhard Meyer, reinhard.meyer@emk-elektronik.de - * - * Shutdown Controller - * Based on AT91SAM9XE datasheet - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef AT91_SHDWN_H -#define AT91_SHDWN_H - -#ifndef __ASSEMBLY__ - -struct at91_shdwn { - u32 cr; /* Control Rer. WO */ - u32 mr; /* Mode Register RW 0x00000003 */ - u32 sr; /* Status Register RO 0x00000000 */ -}; - -#endif /* __ASSEMBLY__ */ - -#define AT91_SHDW_CR_KEY 0xa5000000 -#define AT91_SHDW_CR_SHDW 0x00000001 - -#define AT91_SHDW_MR_RTTWKEN 0x00010000 -#define AT91_SHDW_MR_CPTWK0 0x000000f0 -#define AT91_SHDW_MR_WKMODE0H2L 0x00000002 -#define AT91_SHDW_MR_WKMODE0L2H 0x00000001 - -#define AT91_SHDW_SR_RTTWK 0x00010000 -#define AT91_SHDW_SR_WAKEUP0 0x00000001 - -#endif diff --git a/arch/arm/include/asm/arch-exynos/cpu.h b/arch/arm/include/asm/arch-exynos/cpu.h index ba717146f5..78aceef17b 100644 --- a/arch/arm/include/asm/arch-exynos/cpu.h +++ b/arch/arm/include/asm/arch-exynos/cpu.h @@ -29,6 +29,8 @@ #define EXYNOS4_MIU_BASE 0x10600000 #define EXYNOS4_ACE_SFR_BASE 0x10830000 #define EXYNOS4_GPIO_PART2_BASE 0x11000000 +#define EXYNOS4_GPIO_PART2_0 0x11000000 /* GPJ0 */ +#define EXYNOS4_GPIO_PART2_1 0x11000c00 /* GPX0 */ #define EXYNOS4_GPIO_PART1_BASE 0x11400000 #define EXYNOS4_FIMD_BASE 0x11C00000 #define EXYNOS4_MIPI_DSIM_BASE 0x11C80000 @@ -70,7 +72,14 @@ #define EXYNOS4X12_GPIO_PART4_BASE 0x106E0000 #define EXYNOS4X12_ACE_SFR_BASE 0x10830000 #define EXYNOS4X12_GPIO_PART2_BASE 0x11000000 +#define EXYNOS4X12_GPIO_PART2_0 0x11000000 +#define EXYNOS4X12_GPIO_PART2_1 0x11000040 /* GPK0 */ +#define EXYNOS4X12_GPIO_PART2_2 0x11000260 /* GPM0 */ +#define EXYNOS4X12_GPIO_PART2_3 0x11000c00 /* GPX0 */ #define EXYNOS4X12_GPIO_PART1_BASE 0x11400000 +#define EXYNOS4X12_GPIO_PART1_0 0x11400000 /* GPA0 */ +#define EXYNOS4X12_GPIO_PART1_1 0x11400180 /* GPF0 */ +#define EXYNOS4X12_GPIO_PART1_2 0x11400240 /* GPJ0 */ #define EXYNOS4X12_FIMD_BASE 0x11C00000 #define EXYNOS4X12_MIPI_DSIM_BASE 0x11C80000 #define EXYNOS4X12_USBOTG_BASE 0x12480000 diff --git a/arch/arm/include/asm/arch-exynos/gpio.h b/arch/arm/include/asm/arch-exynos/gpio.h index ad2ece64f4..02287decc2 100644 --- a/arch/arm/include/asm/arch-exynos/gpio.h +++ b/arch/arm/include/asm/arch-exynos/gpio.h @@ -284,7 +284,10 @@ enum exynos4_gpio_pin { EXYNOS4_GPIO_Y65, EXYNOS4_GPIO_Y66, EXYNOS4_GPIO_Y67, - EXYNOS4_GPIO_X00, /* 256 0x100 */ + + /* GPIO_PART2_1 STARTS */ + EXYNOS4_GPIO_MAX_PORT_PART_2_0, /* 256 0x100 */ + EXYNOS4_GPIO_X00 = EXYNOS4_GPIO_MAX_PORT_PART_2_0, EXYNOS4_GPIO_X01, EXYNOS4_GPIO_X02, EXYNOS4_GPIO_X03, @@ -318,8 +321,8 @@ enum exynos4_gpio_pin { EXYNOS4_GPIO_X37, /* GPIO_PART3_STARTS */ - EXYNOS4_GPIO_MAX_PORT_PART_2, /* 288 0x120 */ - EXYNOS4_GPIO_Z0 = EXYNOS4_GPIO_MAX_PORT_PART_2, + EXYNOS4_GPIO_MAX_PORT_PART_2_1, /* 288 0x120 */ + EXYNOS4_GPIO_Z0 = EXYNOS4_GPIO_MAX_PORT_PART_2_1, EXYNOS4_GPIO_Z1, EXYNOS4_GPIO_Z2, EXYNOS4_GPIO_Z3, @@ -332,7 +335,7 @@ enum exynos4_gpio_pin { }; enum exynos4X12_gpio_pin { - /* GPIO_PART1_STARTS */ + /* EXYNOS4X12_GPIO_PART1_0 starts here */ EXYNOS4X12_GPIO_A00, /* 0 */ EXYNOS4X12_GPIO_A01, EXYNOS4X12_GPIO_A02, @@ -389,7 +392,9 @@ enum exynos4X12_gpio_pin { EXYNOS4X12_GPIO_D15, EXYNOS4X12_GPIO_D16, EXYNOS4X12_GPIO_D17, - EXYNOS4X12_GPIO_F00, /* 56 0x38 */ + EXYNOS4X12_GPIO_MAX_PORT_PART_1_0, /* 56 0x38 */ + /* EXYNOS4X12_GPIO_PART1_1 starts here */ + EXYNOS4X12_GPIO_F00 = EXYNOS4X12_GPIO_MAX_PORT_PART_1_0, EXYNOS4X12_GPIO_F01, EXYNOS4X12_GPIO_F02, EXYNOS4X12_GPIO_F03, @@ -421,7 +426,9 @@ enum exynos4X12_gpio_pin { EXYNOS4X12_GPIO_F35, EXYNOS4X12_GPIO_F36, EXYNOS4X12_GPIO_F37, - EXYNOS4X12_GPIO_J00, /* 88 0x58 */ + EXYNOS4X12_GPIO_MAX_PORT_PART_1_1, /* 88 0x58 */ + /* EXYNOS4X12_GPIO_PART1_2 starts here */ + EXYNOS4X12_GPIO_J00 = EXYNOS4X12_GPIO_MAX_PORT_PART_1_1, EXYNOS4X12_GPIO_J01, EXYNOS4X12_GPIO_J02, EXYNOS4X12_GPIO_J03, @@ -438,9 +445,12 @@ enum exynos4X12_gpio_pin { EXYNOS4X12_GPIO_J16, EXYNOS4X12_GPIO_J17, - /* GPIO_PART2_STARTS */ - EXYNOS4X12_GPIO_MAX_PORT_PART_1,/* 104 0x66 */ - EXYNOS4X12_GPIO_K00 = EXYNOS4X12_GPIO_MAX_PORT_PART_1, + /** + * EXYNOS4X12_GPIO_PART2_0 is not used + * EXYNOS4X12_GPIO_PART2_1 starts here + */ + EXYNOS4X12_GPIO_MAX_PORT_PART_1_2, /* 104 0x66 */ + EXYNOS4X12_GPIO_K00 = EXYNOS4X12_GPIO_MAX_PORT_PART_1_2, EXYNOS4X12_GPIO_K01, EXYNOS4X12_GPIO_K02, EXYNOS4X12_GPIO_K03, @@ -552,7 +562,9 @@ enum exynos4X12_gpio_pin { EXYNOS4X12_GPIO_Y65, EXYNOS4X12_GPIO_Y66, EXYNOS4X12_GPIO_Y67, - EXYNOS4X12_GPIO_M00, /* 216 0xd8 */ + EXYNOS4X12_GPIO_MAX_PORT_PART_2_1, /* 216 0xd8 */ + /* EXYNOS4X12_GPIO_PART2_2 starts here */ + EXYNOS4X12_GPIO_M00 = EXYNOS4X12_GPIO_MAX_PORT_PART_2_1, EXYNOS4X12_GPIO_M01, EXYNOS4X12_GPIO_M02, EXYNOS4X12_GPIO_M03, @@ -592,7 +604,9 @@ enum exynos4X12_gpio_pin { EXYNOS4X12_GPIO_M45, EXYNOS4X12_GPIO_M46, EXYNOS4X12_GPIO_M47, - EXYNOS4X12_GPIO_X00, /* 256 0x100 */ + EXYNOS4X12_GPIO_MAX_PORT_PART_2_2, /* 256 0x100 */ + /* EXYNOS4X12_GPIO_PART2_3 starts here */ + EXYNOS4X12_GPIO_X00 = EXYNOS4X12_GPIO_MAX_PORT_PART_2_2, EXYNOS4X12_GPIO_X01, EXYNOS4X12_GPIO_X02, EXYNOS4X12_GPIO_X03, @@ -625,9 +639,9 @@ enum exynos4X12_gpio_pin { EXYNOS4X12_GPIO_X36, EXYNOS4X12_GPIO_X37, - /* GPIO_PART3_STARTS */ - EXYNOS4X12_GPIO_MAX_PORT_PART_2,/* 288 0x120 */ - EXYNOS4X12_GPIO_Z0 = EXYNOS4X12_GPIO_MAX_PORT_PART_2, + /* EXYNOS4X12_GPIO_PART3 starts here */ + EXYNOS4X12_GPIO_MAX_PORT_PART_2_3, /* 288 0x120 */ + EXYNOS4X12_GPIO_Z0 = EXYNOS4X12_GPIO_MAX_PORT_PART_2_3, EXYNOS4X12_GPIO_Z1, EXYNOS4X12_GPIO_Z2, EXYNOS4X12_GPIO_Z3, @@ -636,7 +650,7 @@ enum exynos4X12_gpio_pin { EXYNOS4X12_GPIO_Z6, EXYNOS4X12_GPIO_Z7, - /* GPIO_PART4_STARTS */ + /* EXYNOS4X12_GPIO_PART4 starts here */ EXYNOS4X12_GPIO_MAX_PORT_PART_3,/* 296 0x128 */ EXYNOS4X12_GPIO_V00 = EXYNOS4X12_GPIO_MAX_PORT_PART_3, EXYNOS4X12_GPIO_V01, @@ -1339,17 +1353,22 @@ struct gpio_info { unsigned int max_gpio; /* Maximum GPIO in this part */ }; -#define EXYNOS4_GPIO_NUM_PARTS 3 +#define EXYNOS4_GPIO_NUM_PARTS 4 static struct gpio_info exynos4_gpio_data[EXYNOS4_GPIO_NUM_PARTS] = { { EXYNOS4_GPIO_PART1_BASE, EXYNOS4_GPIO_MAX_PORT_PART_1 }, - { EXYNOS4_GPIO_PART2_BASE, EXYNOS4_GPIO_MAX_PORT_PART_2 }, + { EXYNOS4_GPIO_PART2_0, EXYNOS4_GPIO_MAX_PORT_PART_2_0 }, + { EXYNOS4_GPIO_PART2_1, EXYNOS4_GPIO_MAX_PORT_PART_2_1 }, { EXYNOS4_GPIO_PART3_BASE, EXYNOS4_GPIO_MAX_PORT }, }; -#define EXYNOS4X12_GPIO_NUM_PARTS 4 +#define EXYNOS4X12_GPIO_NUM_PARTS 8 static struct gpio_info exynos4x12_gpio_data[EXYNOS4X12_GPIO_NUM_PARTS] = { - { EXYNOS4X12_GPIO_PART1_BASE, EXYNOS4X12_GPIO_MAX_PORT_PART_1 }, - { EXYNOS4X12_GPIO_PART2_BASE, EXYNOS4X12_GPIO_MAX_PORT_PART_2 }, + { EXYNOS4X12_GPIO_PART1_0, EXYNOS4X12_GPIO_MAX_PORT_PART_1_0 }, + { EXYNOS4X12_GPIO_PART1_1, EXYNOS4X12_GPIO_MAX_PORT_PART_1_1 }, + { EXYNOS4X12_GPIO_PART1_2, EXYNOS4X12_GPIO_MAX_PORT_PART_1_2 }, + { EXYNOS4X12_GPIO_PART2_1, EXYNOS4X12_GPIO_MAX_PORT_PART_2_1 }, + { EXYNOS4X12_GPIO_PART2_2, EXYNOS4X12_GPIO_MAX_PORT_PART_2_2 }, + { EXYNOS4X12_GPIO_PART2_3, EXYNOS4X12_GPIO_MAX_PORT_PART_2_3 }, { EXYNOS4X12_GPIO_PART3_BASE, EXYNOS4X12_GPIO_MAX_PORT_PART_3 }, { EXYNOS4X12_GPIO_PART4_BASE, EXYNOS4X12_GPIO_MAX_PORT }, }; diff --git a/arch/arm/include/asm/arch-keystone/hardware-k2e.h b/arch/arm/include/asm/arch-keystone/hardware-k2e.h index 9512756619..df499957e5 100644 --- a/arch/arm/include/asm/arch-keystone/hardware-k2e.h +++ b/arch/arm/include/asm/arch-keystone/hardware-k2e.h @@ -57,8 +57,6 @@ #define KS2_NETCP_PDMA_SCHED_BASE 0x24186100 #define KS2_NETCP_PDMA_RX_FLOW_BASE 0x24189000 #define KS2_NETCP_PDMA_RX_FLOW_NUM 96 -#define KS2_NETCP_PDMA_RX_FREE_QUEUE 4001 -#define KS2_NETCP_PDMA_RX_RCV_QUEUE 4002 #define KS2_NETCP_PDMA_TX_SND_QUEUE 896 /* NETCP */ diff --git a/arch/arm/include/asm/arch-keystone/hardware-k2hk.h b/arch/arm/include/asm/arch-keystone/hardware-k2hk.h index 5a9ea4fbca..195c0d3003 100644 --- a/arch/arm/include/asm/arch-keystone/hardware-k2hk.h +++ b/arch/arm/include/asm/arch-keystone/hardware-k2hk.h @@ -98,8 +98,6 @@ #define KS2_NETCP_PDMA_SCHED_BASE 0x02004c00 #define KS2_NETCP_PDMA_RX_FLOW_BASE 0x02005000 #define KS2_NETCP_PDMA_RX_FLOW_NUM 32 -#define KS2_NETCP_PDMA_RX_FREE_QUEUE 4001 -#define KS2_NETCP_PDMA_RX_RCV_QUEUE 4002 #define KS2_NETCP_PDMA_TX_SND_QUEUE 648 /* NETCP */ diff --git a/arch/arm/include/asm/arch-keystone/hardware-k2l.h b/arch/arm/include/asm/arch-keystone/hardware-k2l.h index 05532ada70..4f1197ea92 100644 --- a/arch/arm/include/asm/arch-keystone/hardware-k2l.h +++ b/arch/arm/include/asm/arch-keystone/hardware-k2l.h @@ -84,6 +84,10 @@ /* OSR memory size */ #define KS2_OSR_SIZE 0x100000 +/* SGMII SerDes */ +#define KS2_SGMII_SERDES2_BASE 0x02320000 +#define KS2_LANES_PER_SGMII_SERDES 2 + /* Number of DSP cores */ #define KS2_NUM_DSPS 4 @@ -98,4 +102,7 @@ #define KS2_NETCP_PDMA_RX_FLOW_NUM 96 #define KS2_NETCP_PDMA_TX_SND_QUEUE 896 +/* NETCP */ +#define KS2_NETCP_BASE 0x26000000 + #endif /* __ASM_ARCH_HARDWARE_K2L_H */ diff --git a/arch/arm/include/asm/arch-keystone/hardware.h b/arch/arm/include/asm/arch-keystone/hardware.h index c6a54d8b91..be22bdb1ca 100644 --- a/arch/arm/include/asm/arch-keystone/hardware.h +++ b/arch/arm/include/asm/arch-keystone/hardware.h @@ -122,6 +122,10 @@ typedef volatile unsigned int *dv_reg_p; #define KS2_EDMA_QEESR 0x108c #define KS2_EDMA_PARAM_1(x) (0x4020 + (4 * x)) +/* NETCP pktdma */ +#define KS2_NETCP_PDMA_RX_FREE_QUEUE 4001 +#define KS2_NETCP_PDMA_RX_RCV_QUEUE 4002 + /* Chip Interrupt Controller */ #define KS2_CIC2_BASE 0x02608000 diff --git a/arch/arm/include/asm/arch-mx6/crm_regs.h b/arch/arm/include/asm/arch-mx6/crm_regs.h index e67b5b9e7d..39f3c0707b 100644 --- a/arch/arm/include/asm/arch-mx6/crm_regs.h +++ b/arch/arm/include/asm/arch-mx6/crm_regs.h @@ -89,7 +89,7 @@ struct mxc_ccm_reg { u32 analog_pll_video_tog; u32 analog_pll_video_num; /* 0x40b0 */ u32 analog_reserved6[3]; - u32 analog_pll_vedio_denon; /* 0x40c0 */ + u32 analog_pll_video_denom; /* 0x40c0 */ u32 analog_reserved7[7]; u32 analog_pll_enet; /* 0x40e0 */ u32 analog_pll_enet_set; @@ -228,6 +228,8 @@ struct mxc_ccm_reg { #ifdef CONFIG_MX6SX #define MXC_CCM_CSCMR1_QSPI1_CLK_SEL_MASK (0x7 << 7) #define MXC_CCM_CSCMR1_QSPI1_CLK_SEL_OFFSET 7 +#endif +#if (defined(CONFIG_MX6SL) || defined(CONFIG_MX6SX)) #define MXC_CCM_CSCMR1_PER_CLK_SEL_MASK (1 << 6) #define MXC_CCM_CSCMR1_PER_CLK_SEL_OFFSET 6 #endif @@ -931,10 +933,10 @@ struct mxc_ccm_reg { #define BF_ANADIG_PLL_VIDEO_RSVD0(v) \ (((v) << 22) & BM_ANADIG_PLL_VIDEO_RSVD0) #define BM_ANADIG_PLL_VIDEO_SSC_EN 0x00200000 -#define BP_ANADIG_PLL_VIDEO_TEST_DIV_SELECT 19 -#define BM_ANADIG_PLL_VIDEO_TEST_DIV_SELECT 0x00180000 -#define BF_ANADIG_PLL_VIDEO_TEST_DIV_SELECT(v) \ - (((v) << 19) & BM_ANADIG_PLL_VIDEO_TEST_DIV_SELECT) +#define BP_ANADIG_PLL_VIDEO_POST_DIV_SELECT 19 +#define BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT 0x00180000 +#define BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(v) \ + (((v) << 19) & BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT) #define BM_ANADIG_PLL_VIDEO_PFD_OFFSET_EN 0x00040000 #define BM_ANADIG_PLL_VIDEO_DITHER_ENABLE 0x00020000 #define BM_ANADIG_PLL_VIDEO_BYPASS 0x00010000 diff --git a/arch/arm/include/asm/arch-mx6/mx6sl_pins.h b/arch/arm/include/asm/arch-mx6/mx6sl_pins.h index 045ccc4512..d9db58c9a3 100644 --- a/arch/arm/include/asm/arch-mx6/mx6sl_pins.h +++ b/arch/arm/include/asm/arch-mx6/mx6sl_pins.h @@ -14,12 +14,31 @@ enum { MX6_PAD_ECSPI1_MOSI__ECSPI_MOSI = IOMUX_PAD(0x035C, 0x006C, 0, 0x0688, 0, 0), MX6_PAD_ECSPI1_SCLK__ECSPI_SCLK = IOMUX_PAD(0x0360, 0x0070, 0, 0x067C, 0, 0), MX6_PAD_ECSPI1_SS0__GPIO4_IO11 = IOMUX_PAD(0x0364, 0x0074, 5, 0x0000, 0, 0), + MX6_PAD_SD1_CLK__USDHC1_CLK = IOMUX_PAD(0x0534, 0x022C, 0, 0x0000, 0, 0), + MX6_PAD_SD1_CMD__USDHC1_CMD = IOMUX_PAD(0x0538, 0x0230, 0, 0x0000, 0, 0), + MX6_PAD_SD1_DAT0__USDHC1_DAT0 = IOMUX_PAD(0x053C, 0x0234, 0, 0x0000, 0, 0), + MX6_PAD_SD1_DAT1__USDHC1_DAT1 = IOMUX_PAD(0x0540, 0x0238, 0, 0x0000, 0, 0), + MX6_PAD_SD1_DAT2__USDHC1_DAT2 = IOMUX_PAD(0x0544, 0x023C, 0, 0x0000, 0, 0), + MX6_PAD_SD1_DAT3__USDHC1_DAT3 = IOMUX_PAD(0x0548, 0x0240, 0, 0x0000, 0, 0), + MX6_PAD_SD1_DAT4__USDHC1_DAT4 = IOMUX_PAD(0x054C, 0x0244, 0, 0x0000, 0, 0), + MX6_PAD_SD1_DAT5__USDHC1_DAT5 = IOMUX_PAD(0x0550, 0x0248, 0, 0x0000, 0, 0), + MX6_PAD_SD1_DAT6__USDHC1_DAT6 = IOMUX_PAD(0x0554, 0x024C, 0, 0x0000, 0, 0), + MX6_PAD_SD1_DAT7__USDHC1_DAT7 = IOMUX_PAD(0x0558, 0x0250, 0, 0x0000, 0, 0), + MX6_PAD_KEY_ROW7__GPIO_4_7 = IOMUX_PAD(0x04B0, 0x01A8, 5, 0x0000, 0, 0), MX6_PAD_SD2_CLK__USDHC2_CLK = IOMUX_PAD(0x055C, 0x0254, 0, 0x0000, 0, 0), MX6_PAD_SD2_CMD__USDHC2_CMD = IOMUX_PAD(0x0560, 0x0258, 0, 0x0000, 0, 0), MX6_PAD_SD2_DAT0__USDHC2_DAT0 = IOMUX_PAD(0x0564, 0x025C, 0, 0x0000, 0, 0), MX6_PAD_SD2_DAT1__USDHC2_DAT1 = IOMUX_PAD(0x0568, 0x0260, 0, 0x0000, 0, 0), MX6_PAD_SD2_DAT2__USDHC2_DAT2 = IOMUX_PAD(0x056C, 0x0264, 0, 0x0000, 0, 0), MX6_PAD_SD2_DAT3__USDHC2_DAT3 = IOMUX_PAD(0x0570, 0x0268, 0, 0x0000, 0, 0), + MX6_PAD_SD2_DAT7__GPIO_5_0 = IOMUX_PAD(0x0580, 0x0278, 5, 0x0000, 0, 0), + MX6_PAD_SD3_CLK__USDHC3_CLK = IOMUX_PAD(0x0588, 0x0280, 0, 0x0000, 0, 0), + MX6_PAD_SD3_CMD__USDHC3_CMD = IOMUX_PAD(0x058C, 0x0284, 0, 0x0000, 0, 0), + MX6_PAD_SD3_DAT0__USDHC3_DAT0 = IOMUX_PAD(0x0590, 0x0288, 0, 0x0000, 0, 0), + MX6_PAD_SD3_DAT1__USDHC3_DAT1 = IOMUX_PAD(0x0594, 0x028C, 0, 0x0000, 0, 0), + MX6_PAD_SD3_DAT2__USDHC3_DAT2 = IOMUX_PAD(0x0598, 0x0290, 0, 0x0000, 0, 0), + MX6_PAD_SD3_DAT3__USDHC3_DAT3 = IOMUX_PAD(0x059C, 0x0294, 0, 0x0000, 0, 0), + MX6_PAD_REF_CLK_32K__GPIO_3_22 = IOMUX_PAD(0x0530, 0x0228, 5, 0x0000, 0, 0), MX6_PAD_UART1_RXD__UART1_RXD = IOMUX_PAD(0x05A0, 0x0298, 0, 0x07FC, 0, 0), MX6_PAD_UART1_TXD__UART1_TXD = IOMUX_PAD(0x05A4, 0x029C, 0, 0x0000, 0, 0), diff --git a/arch/arm/include/asm/arch-rmobile/rcar-base.h b/arch/arm/include/asm/arch-rmobile/rcar-base.h index 027e9b1b14..9c1439b764 100644 --- a/arch/arm/include/asm/arch-rmobile/rcar-base.h +++ b/arch/arm/include/asm/arch-rmobile/rcar-base.h @@ -385,6 +385,8 @@ #define PLL0CR 0xE61500D8 #define PLL0_STC_MASK 0x7F000000 #define PLL0_STC_BIT 24 +#define PLLECR 0xE61500D0 +#define PLL0ST 0x100 #ifndef __ASSEMBLY__ #include <asm/types.h> diff --git a/arch/arm/include/asm/arch-sunxi/clock.h b/arch/arm/include/asm/arch-sunxi/clock.h index c562f621c2..42382a8ae2 100644 --- a/arch/arm/include/asm/arch-sunxi/clock.h +++ b/arch/arm/include/asm/arch-sunxi/clock.h @@ -15,7 +15,7 @@ #define CLK_GATE_CLOSE 0x0 /* clock control module regs definition */ -#if defined(CONFIG_SUN6I) || defined(CONFIG_SUN8I) +#if defined(CONFIG_MACH_SUN6I) || defined(CONFIG_MACH_SUN8I) #include <asm/arch/clock_sun6i.h> #else #include <asm/arch/clock_sun4i.h> diff --git a/arch/arm/include/asm/arch-sunxi/gpio.h b/arch/arm/include/asm/arch-sunxi/gpio.h index 7bb649950a..437dd35b68 100644 --- a/arch/arm/include/asm/arch-sunxi/gpio.h +++ b/arch/arm/include/asm/arch-sunxi/gpio.h @@ -155,7 +155,7 @@ enum sunxi_gpio_number { #define SUNXI_GPF2_SDC0 2 -#ifdef CONFIG_SUN8I +#ifdef CONFIG_MACH_SUN8I #define SUNXI_GPF2_UART0_TX 3 #define SUNXI_GPF4_UART0_RX 3 #else @@ -180,7 +180,9 @@ enum sunxi_gpio_number { #define SUNXI_GPIO_PULL_UP 1 #define SUNXI_GPIO_PULL_DOWN 2 -int sunxi_gpio_set_cfgpin(u32 pin, u32 val); +void sunxi_gpio_set_cfgbank(struct sunxi_gpio *pio, int bank_offset, u32 val); +void sunxi_gpio_set_cfgpin(u32 pin, u32 val); +int sunxi_gpio_get_cfgbank(struct sunxi_gpio *pio, int bank_offset); int sunxi_gpio_get_cfgpin(u32 pin); int sunxi_gpio_set_drv(u32 pin, u32 val); int sunxi_gpio_set_pull(u32 pin, u32 val); diff --git a/arch/arm/include/asm/arch-sunxi/mmc.h b/arch/arm/include/asm/arch-sunxi/mmc.h index 8a216740a7..537f145564 100644 --- a/arch/arm/include/asm/arch-sunxi/mmc.h +++ b/arch/arm/include/asm/arch-sunxi/mmc.h @@ -43,7 +43,7 @@ struct sunxi_mmc { u32 chda; /* 0x90 */ u32 cbda; /* 0x94 */ u32 res1[26]; -#if defined(CONFIG_SUN6I) || defined(CONFIG_SUN8I) +#if defined(CONFIG_MACH_SUN6I) || defined(CONFIG_MACH_SUN8I) u32 res2[64]; #endif u32 fifo; /* 0x100 (0x200 on sun6i) FIFO access address */ diff --git a/arch/arm/include/asm/arch-sunxi/timer.h b/arch/arm/include/asm/arch-sunxi/timer.h index 03a0684c79..9a5e488a38 100644 --- a/arch/arm/include/asm/arch-sunxi/timer.h +++ b/arch/arm/include/asm/arch-sunxi/timer.h @@ -67,7 +67,7 @@ struct sunxi_timer_reg { struct sunxi_timer timer[6]; /* We have 6 timers */ u8 res2[16]; struct sunxi_avs avs; -#if defined(CONFIG_SUN4I) || defined(CONFIG_SUN5I) || defined(CONFIG_SUN7I) +#if defined(CONFIG_MACH_SUN4I) || defined(CONFIG_MACH_SUN5I) || defined(CONFIG_MACH_SUN7I) struct sunxi_wdog wdog; /* 0x90 */ /* XXX the following is not accurate for sun5i/sun7i */ struct sunxi_64cnt cnt64; /* 0xa0 */ @@ -77,7 +77,7 @@ struct sunxi_timer_reg { struct sunxi_tgp tgp[4]; u8 res5[8]; u32 cpu_cfg; -#else /* CONFIG_SUN6I || CONFIG_SUN8I || ... */ +#else /* CONFIG_MACH_SUN6I || CONFIG_MACH_SUN8I || ... */ u8 res3[16]; struct sunxi_wdog wdog[5]; /* We have 5 watchdogs */ #endif diff --git a/arch/arm/include/asm/arch-sunxi/watchdog.h b/arch/arm/include/asm/arch-sunxi/watchdog.h index ccc8fa32c4..8108be97ba 100644 --- a/arch/arm/include/asm/arch-sunxi/watchdog.h +++ b/arch/arm/include/asm/arch-sunxi/watchdog.h @@ -13,7 +13,7 @@ #define WDT_CTRL_RESTART (0x1 << 0) #define WDT_CTRL_KEY (0x0a57 << 1) -#if defined(CONFIG_SUN4I) || defined(CONFIG_SUN5I) || defined(CONFIG_SUN7I) +#if defined(CONFIG_MACH_SUN4I) || defined(CONFIG_MACH_SUN5I) || defined(CONFIG_MACH_SUN7I) #define WDT_MODE_EN (0x1 << 0) #define WDT_MODE_RESET_EN (0x1 << 1) diff --git a/arch/arm/include/asm/arch-uniphier/ehci-uniphier.h b/arch/arm/include/asm/arch-uniphier/ehci-uniphier.h new file mode 100644 index 0000000000..e9c5fb4af8 --- /dev/null +++ b/arch/arm/include/asm/arch-uniphier/ehci-uniphier.h @@ -0,0 +1,33 @@ +/* + * Copyright (C) 2014 Panasonic Corporation + * Author: Masahiro Yamada <yamada.m@jp.panasonic.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __PLAT_UNIPHIER_EHCI_H +#define __PLAT_UNIPHIER_EHCI_H + +#include <linux/types.h> +#include <asm/io.h> +#include "mio-regs.h" + +struct uniphier_ehci_platform_data { + unsigned long base; +}; + +extern struct uniphier_ehci_platform_data uniphier_ehci_platdata[]; + +static inline void uniphier_ehci_reset(int index, int on) +{ + u32 tmp; + + tmp = readl(MIO_USB_RSTCTRL(index)); + if (on) + tmp &= ~MIO_USB_RSTCTRL_XRST; + else + tmp |= MIO_USB_RSTCTRL_XRST; + writel(tmp, MIO_USB_RSTCTRL(index)); +} + +#endif /* __PLAT_UNIPHIER_EHCI_H */ diff --git a/arch/arm/include/asm/arch-uniphier/mio-regs.h b/arch/arm/include/asm/arch-uniphier/mio-regs.h new file mode 100644 index 0000000000..3306934ff7 --- /dev/null +++ b/arch/arm/include/asm/arch-uniphier/mio-regs.h @@ -0,0 +1,20 @@ +/* + * UniPhier MIO (Media I/O) registers + * + * Copyright (C) 2014 Panasonic Corporation + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef ARCH_MIO_REGS_H +#define ARCH_MIO_REGS_H + +#define MIO_BASE 0x59810000 + +#define MIO_CLKCTRL(i) (MIO_BASE + 0x200 * (i) + 0x0020) +#define MIO_RSTCTRL(i) (MIO_BASE + 0x200 * (i) + 0x0110) +#define MIO_USB_RSTCTRL(i) (MIO_BASE + 0x200 * (i) + 0x0114) + +#define MIO_USB_RSTCTRL_XRST (0x1 << 0) + +#endif /* ARCH_MIO_REGS_H */ diff --git a/arch/arm/include/asm/arch-uniphier/platdevice.h b/arch/arm/include/asm/arch-uniphier/platdevice.h index cdf7d132d4..62a512659c 100644 --- a/arch/arm/include/asm/arch-uniphier/platdevice.h +++ b/arch/arm/include/asm/arch-uniphier/platdevice.h @@ -21,4 +21,6 @@ U_BOOT_DEVICE(serial##n) = { \ .platdata = &serial_device##n \ }; +#include <asm/arch/ehci-uniphier.h> + #endif /* ARCH_PLATDEVICE_H */ diff --git a/arch/arm/include/asm/arch-uniphier/sg-regs.h b/arch/arm/include/asm/arch-uniphier/sg-regs.h index 79d7ec7148..fa5e6ae0f2 100644 --- a/arch/arm/include/asm/arch-uniphier/sg-regs.h +++ b/arch/arm/include/asm/arch-uniphier/sg-regs.h @@ -88,7 +88,18 @@ #define SG_PINMON0_CLK_MODE_AXOSEL_20480KHZ (0x2 << 16) #define SG_PINMON0_CLK_MODE_AXOSEL_25000KHZ_A (0x3 << 16) -#ifndef __ASSEMBLY__ +#ifdef __ASSEMBLY__ + + .macro set_pinsel, n, value, ra, rd + ldr \ra, =SG_PINSEL_ADDR(\n) + ldr \rd, [\ra] + and \rd, \rd, #SG_PINSEL_MASK(\n) + orr \rd, \rd, #SG_PINSEL_MODE(\n, \value) + str \rd, [\ra] + .endm + +#else + #include <linux/types.h> #include <asm/io.h> diff --git a/arch/arm/include/asm/imx-common/iomux-v3.h b/arch/arm/include/asm/imx-common/iomux-v3.h index a8ca49c343..e0a49be4ff 100644 --- a/arch/arm/include/asm/imx-common/iomux-v3.h +++ b/arch/arm/include/asm/imx-common/iomux-v3.h @@ -182,6 +182,11 @@ typedef u64 iomux_v3_cfg_t; void imx_iomux_v3_setup_pad(iomux_v3_cfg_t pad); void imx_iomux_v3_setup_multiple_pads(iomux_v3_cfg_t const *pad_list, unsigned count); +/* +* Set bits for general purpose registers +*/ +void imx_iomux_set_gpr_register(int group, int start_bit, + int num_bits, int value); /* macros for declaring and using pinmux array */ #if defined(CONFIG_MX6QDL) diff --git a/arch/arm/include/asm/macro.h b/arch/arm/include/asm/macro.h index 541b443254..1c8c4251ee 100644 --- a/arch/arm/include/asm/macro.h +++ b/arch/arm/include/asm/macro.h @@ -193,7 +193,7 @@ lr .req x30 0 : wfi ldr \wreg2, [\xreg1, GICC_AIAR] str \wreg2, [\xreg1, GICC_AEOIR] - and \wreg2, \wreg2, #3ff + and \wreg2, \wreg2, #0x3ff cbnz \wreg2, 0b .endm #endif diff --git a/arch/arm/include/debug/8250.S b/arch/arm/include/debug/8250.S new file mode 100644 index 0000000000..d47a892652 --- /dev/null +++ b/arch/arm/include/debug/8250.S @@ -0,0 +1,52 @@ +/* + * arch/arm/include/debug/8250.S + * + * Copyright (C) 1994-2013 Russell King + * + * SPDX-License-Identifier: GPL-2.0+ + */ +#include <linux/serial_reg.h> + + .macro addruart, rp, rv, tmp + ldr \rp, =CONFIG_DEBUG_UART_PHYS + ldr \rv, =CONFIG_DEBUG_UART_VIRT + .endm + +#ifdef CONFIG_DEBUG_UART_8250_WORD + .macro store, rd, rx:vararg + str \rd, \rx + .endm + + .macro load, rd, rx:vararg + ldr \rd, \rx + .endm +#else + .macro store, rd, rx:vararg + strb \rd, \rx + .endm + + .macro load, rd, rx:vararg + ldrb \rd, \rx + .endm +#endif + +#define UART_SHIFT CONFIG_DEBUG_UART_8250_SHIFT + + .macro senduart,rd,rx + store \rd, [\rx, #UART_TX << UART_SHIFT] + .endm + + .macro busyuart,rd,rx +1002: load \rd, [\rx, #UART_LSR << UART_SHIFT] + and \rd, \rd, #UART_LSR_TEMT | UART_LSR_THRE + teq \rd, #UART_LSR_TEMT | UART_LSR_THRE + bne 1002b + .endm + + .macro waituart,rd,rx +#ifdef CONFIG_DEBUG_UART_8250_FLOW_CONTROL +1001: load \rd, [\rx, #UART_MSR << UART_SHIFT] + tst \rd, #UART_MSR_CTS + beq 1001b +#endif + .endm diff --git a/arch/arm/lib/Makefile b/arch/arm/lib/Makefile index 1ef240047f..d74e4b8415 100644 --- a/arch/arm/lib/Makefile +++ b/arch/arm/lib/Makefile @@ -48,6 +48,8 @@ ifndef CONFIG_ARM64 obj-y += cache-cp15.o endif +obj-$(CONFIG_DEBUG_LL) += debug.o + # For EABI conformant tool chains, provide eabi_compat() ifneq (,$(findstring -mabi=aapcs-linux,$(PLATFORM_CPPFLAGS))) extra-y += eabi_compat.o diff --git a/arch/arm/lib/bootm.c b/arch/arm/lib/bootm.c index cdb1975105..4949d573af 100644 --- a/arch/arm/lib/bootm.c +++ b/arch/arm/lib/bootm.c @@ -15,7 +15,6 @@ #include <common.h> #include <command.h> #include <image.h> -#include <vxworks.h> #include <u-boot/zlib.h> #include <asm/byteorder.h> #include <libfdt.h> diff --git a/arch/arm/lib/debug.S b/arch/arm/lib/debug.S new file mode 100644 index 0000000000..760ba74a3c --- /dev/null +++ b/arch/arm/lib/debug.S @@ -0,0 +1,136 @@ +/* + * linux/arch/arm/kernel/debug.S + * + * Copyright (C) 1994-1999 Russell King + * + * SPDX-License-Identifier: GPL-2.0+ + * + * 32-bit debugging code + */ +#include <linux/linkage.h> +#include <asm/assembler.h> + + .text + +/* + * Some debugging routines (useful if you've got MM problems and + * printk isn't working). For DEBUGGING ONLY!!! Do not leave + * references to these in a production kernel! + */ + +#if !defined(CONFIG_DEBUG_SEMIHOSTING) +#include CONFIG_DEBUG_LL_INCLUDE +#endif + +#ifdef CONFIG_MMU + .macro addruart_current, rx, tmp1, tmp2 + addruart \tmp1, \tmp2, \rx + mrc p15, 0, \rx, c1, c0 + tst \rx, #1 + moveq \rx, \tmp1 + movne \rx, \tmp2 + .endm + +#else /* !CONFIG_MMU */ + .macro addruart_current, rx, tmp1, tmp2 + addruart \rx, \tmp1, \tmp2 + .endm + +#endif /* CONFIG_MMU */ + +/* + * Useful debugging routines + */ +ENTRY(printhex8) + mov r1, #8 + b printhex +ENDPROC(printhex8) + +ENTRY(printhex4) + mov r1, #4 + b printhex +ENDPROC(printhex4) + +ENTRY(printhex2) + mov r1, #2 +printhex: adr r2, hexbuf + add r3, r2, r1 + mov r1, #0 + strb r1, [r3] +1: and r1, r0, #15 + mov r0, r0, lsr #4 + cmp r1, #10 + addlt r1, r1, #'0' + addge r1, r1, #'a' - 10 + strb r1, [r3, #-1]! + teq r3, r2 + bne 1b + mov r0, r2 + b printascii +ENDPROC(printhex2) + +hexbuf: .space 16 + + .ltorg + +#ifndef CONFIG_DEBUG_SEMIHOSTING + +ENTRY(printascii) + addruart_current r3, r1, r2 + b 2f +1: waituart r2, r3 + senduart r1, r3 + busyuart r2, r3 + teq r1, #'\n' + moveq r1, #'\r' + beq 1b +2: teq r0, #0 + ldrneb r1, [r0], #1 + teqne r1, #0 + bne 1b + mov pc, lr +ENDPROC(printascii) + +ENTRY(printch) + addruart_current r3, r1, r2 + mov r1, r0 + mov r0, #0 + b 1b +ENDPROC(printch) + +#ifdef CONFIG_MMU +ENTRY(debug_ll_addr) + addruart r2, r3, ip + str r2, [r0] + str r3, [r1] + mov pc, lr +ENDPROC(debug_ll_addr) +#endif + +#else + +ENTRY(printascii) + mov r1, r0 + mov r0, #0x04 @ SYS_WRITE0 + ARM( svc #0x123456 ) + THUMB( svc #0xab ) + mov pc, lr +ENDPROC(printascii) + +ENTRY(printch) + adr r1, hexbuf + strb r0, [r1] + mov r0, #0x03 @ SYS_WRITEC + ARM( svc #0x123456 ) + THUMB( svc #0xab ) + mov pc, lr +ENDPROC(printch) + +ENTRY(debug_ll_addr) + mov r2, #0 + str r2, [r0] + str r2, [r1] + mov pc, lr +ENDPROC(debug_ll_addr) + +#endif |