diff options
Diffstat (limited to 'arch/powerpc/cpu/mpc85xx/cpu_init.c')
| -rw-r--r-- | arch/powerpc/cpu/mpc85xx/cpu_init.c | 161 |
1 files changed, 137 insertions, 24 deletions
diff --git a/arch/powerpc/cpu/mpc85xx/cpu_init.c b/arch/powerpc/cpu/mpc85xx/cpu_init.c index 81aeadd363..36ef23232e 100644 --- a/arch/powerpc/cpu/mpc85xx/cpu_init.c +++ b/arch/powerpc/cpu/mpc85xx/cpu_init.c @@ -33,9 +33,35 @@ #endif #include "../../../../drivers/block/fsl_sata.h" +#ifdef CONFIG_U_QE +#include "../../../../drivers/qe/qe.h" +#endif DECLARE_GLOBAL_DATA_PTR; +#ifdef CONFIG_SYS_FSL_SINGLE_SOURCE_CLK +/* + * For deriving usb clock from 100MHz sysclk, reference divisor is set + * to a value of 5, which gives an intermediate value 20(100/5). The + * multiplication factor integer is set to 24, which when multiplied to + * above intermediate value provides clock for usb ip. + */ +void usb_single_source_clk_configure(struct ccsr_usb_phy *usb_phy) +{ + sys_info_t sysinfo; + + get_sys_info(&sysinfo); + if (sysinfo.diff_sysclk == 1) { + clrbits_be32(&usb_phy->pllprg[1], + CONFIG_SYS_FSL_USB_PLLPRG2_MFI); + setbits_be32(&usb_phy->pllprg[1], + CONFIG_SYS_FSL_USB_PLLPRG2_REF_DIV_INTERNAL_CLK | + CONFIG_SYS_FSL_USB_PLLPRG2_MFI_INTERNAL_CLK | + CONFIG_SYS_FSL_USB_INTERNAL_SOC_CLK_EN); + } +} +#endif + #ifdef CONFIG_SYS_FSL_ERRATUM_A006261 void fsl_erratum_a006261_workaround(struct ccsr_usb_phy __iomem *usb_phy) { @@ -84,7 +110,7 @@ void fsl_erratum_a006261_workaround(struct ccsr_usb_phy __iomem *usb_phy) #endif -#ifdef CONFIG_QE +#if defined(CONFIG_QE) && !defined(CONFIG_U_QE) extern qe_iop_conf_t qe_iop_conf_tab[]; extern void qe_config_iopin(u8 port, u8 pin, int dir, int open_drain, int assign); @@ -173,17 +199,14 @@ void config_8560_ioports (volatile ccsr_cpm_t * cpm) #endif #ifdef CONFIG_SYS_FSL_CPC -static void enable_cpc(void) +#if defined(CONFIG_RAMBOOT_PBL) || defined(CONFIG_SYS_CPC_REINIT_F) +static void disable_cpc_sram(void) { int i; - u32 size = 0; cpc_corenet_t *cpc = (cpc_corenet_t *)CONFIG_SYS_FSL_CPC_ADDR; for (i = 0; i < CONFIG_SYS_NUM_CPC; i++, cpc++) { - u32 cpccfg0 = in_be32(&cpc->cpccfg0); - size += CPC_CFG0_SZ_K(cpccfg0); -#ifdef CONFIG_RAMBOOT_PBL if (in_be32(&cpc->cpcsrcr0) & CPC_SRCR0_SRAMEN) { /* find and disable LAW of SRAM */ struct law_entry law = find_law(CONFIG_SYS_INIT_L3_ADDR); @@ -198,8 +221,21 @@ static void enable_cpc(void) out_be32(&cpc->cpccsr0, 0); out_be32(&cpc->cpcsrcr0, 0); } + } +} #endif +static void enable_cpc(void) +{ + int i; + u32 size = 0; + + cpc_corenet_t *cpc = (cpc_corenet_t *)CONFIG_SYS_FSL_CPC_ADDR; + + for (i = 0; i < CONFIG_SYS_NUM_CPC; i++, cpc++) { + u32 cpccfg0 = in_be32(&cpc->cpccfg0); + size += CPC_CFG0_SZ_K(cpccfg0); + #ifdef CONFIG_SYS_FSL_ERRATUM_CPC_A002 setbits_be32(&cpc->cpchdbcr0, CPC_HDBCR0_TAG_ECC_SCRUB_DIS); #endif @@ -267,11 +303,77 @@ static void corenet_tb_init(void) } #endif +#ifdef CONFIG_SYS_FSL_ERRATUM_A007212 +void fsl_erratum_a007212_workaround(void) +{ + ccsr_gur_t __iomem *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + u32 ddr_pll_ratio; + u32 __iomem *plldgdcr1 = (void *)(CONFIG_SYS_DCSRBAR + 0x21c20); + u32 __iomem *plldadcr1 = (void *)(CONFIG_SYS_DCSRBAR + 0x21c28); + u32 __iomem *dpdovrcr4 = (void *)(CONFIG_SYS_DCSRBAR + 0x21e80); +#if (CONFIG_NUM_DDR_CONTROLLERS >= 2) + u32 __iomem *plldgdcr2 = (void *)(CONFIG_SYS_DCSRBAR + 0x21c40); + u32 __iomem *plldadcr2 = (void *)(CONFIG_SYS_DCSRBAR + 0x21c48); +#if (CONFIG_NUM_DDR_CONTROLLERS >= 3) + u32 __iomem *plldgdcr3 = (void *)(CONFIG_SYS_DCSRBAR + 0x21c60); + u32 __iomem *plldadcr3 = (void *)(CONFIG_SYS_DCSRBAR + 0x21c68); +#endif +#endif + /* + * Even this workaround applies to selected version of SoCs, it is + * safe to apply to all versions, with the limitation of odd ratios. + * If RCW has disabled DDR PLL, we have to apply this workaround, + * otherwise DDR will not work. + */ + ddr_pll_ratio = (in_be32(&gur->rcwsr[0]) >> + FSL_CORENET_RCWSR0_MEM_PLL_RAT_SHIFT) & + FSL_CORENET_RCWSR0_MEM_PLL_RAT_MASK; + /* check if RCW sets ratio to 0, required by this workaround */ + if (ddr_pll_ratio != 0) + return; + ddr_pll_ratio = (in_be32(&gur->rcwsr[0]) >> + FSL_CORENET_RCWSR0_MEM_PLL_RAT_RESV_SHIFT) & + FSL_CORENET_RCWSR0_MEM_PLL_RAT_MASK; + /* check if reserved bits have the desired ratio */ + if (ddr_pll_ratio == 0) { + printf("Error: Unknown DDR PLL ratio!\n"); + return; + } + ddr_pll_ratio >>= 1; + + setbits_be32(plldadcr1, 0x02000001); +#if (CONFIG_NUM_DDR_CONTROLLERS >= 2) + setbits_be32(plldadcr2, 0x02000001); +#if (CONFIG_NUM_DDR_CONTROLLERS >= 3) + setbits_be32(plldadcr3, 0x02000001); +#endif +#endif + setbits_be32(dpdovrcr4, 0xe0000000); + out_be32(plldgdcr1, 0x08000001 | (ddr_pll_ratio << 1)); +#if (CONFIG_NUM_DDR_CONTROLLERS >= 2) + out_be32(plldgdcr2, 0x08000001 | (ddr_pll_ratio << 1)); +#if (CONFIG_NUM_DDR_CONTROLLERS >= 3) + out_be32(plldgdcr3, 0x08000001 | (ddr_pll_ratio << 1)); +#endif +#endif + udelay(100); + clrbits_be32(plldadcr1, 0x02000001); +#if (CONFIG_NUM_DDR_CONTROLLERS >= 2) + clrbits_be32(plldadcr2, 0x02000001); +#if (CONFIG_NUM_DDR_CONTROLLERS >= 3) + clrbits_be32(plldadcr3, 0x02000001); +#endif +#endif + clrbits_be32(dpdovrcr4, 0xe0000000); +} +#endif + void cpu_init_f (void) { extern void m8560_cpm_reset (void); #ifdef CONFIG_SYS_DCSRBAR_PHYS ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + gd = (gd_t *)(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET); #endif #if defined(CONFIG_SECURE_BOOT) struct law_entry law; @@ -298,6 +400,10 @@ void cpu_init_f (void) law = find_law(CONFIG_SYS_PBI_FLASH_BASE); if (law.index != -1) disable_law(law.index); + +#if defined(CONFIG_SYS_CPC_REINIT_F) + disable_cpc_sram(); +#endif #endif #ifdef CONFIG_CPM2 @@ -309,10 +415,12 @@ void cpu_init_f (void) #if defined(CONFIG_CPM2) m8560_cpm_reset(); #endif -#ifdef CONFIG_QE + +#if defined(CONFIG_QE) && !defined(CONFIG_U_QE) /* Config QE ioports */ config_qe_ioports(); #endif + #if defined(CONFIG_FSL_DMA) dma_init(); #endif @@ -330,6 +438,17 @@ void cpu_init_f (void) in_be32(&gur->dcsrcr); #endif +#ifdef CONFIG_SYS_DCSRBAR_PHYS +#ifdef CONFIG_DEEP_SLEEP + /* disable the console if boot from deep sleep */ + if (in_be32(&gur->scrtsr[0]) & (1 << 3)) + gd->flags |= GD_FLG_SILENT | GD_FLG_DISABLE_CONSOLE; +#endif +#endif +#ifdef CONFIG_SYS_FSL_ERRATUM_A007212 + fsl_erratum_a007212_workaround(); +#endif + } /* Implement a dummy function for those platforms w/o SERDES */ @@ -598,6 +717,9 @@ skip_l2: puts("disabled\n"); #endif +#if defined(CONFIG_RAMBOOT_PBL) + disable_cpc_sram(); +#endif enable_cpc(); #ifndef CONFIG_SYS_FSL_NO_SERDES @@ -716,6 +838,9 @@ skip_l2: CONFIG_SYS_FSL_USB_PLLPRG2_PHY1_CLK_EN | CONFIG_SYS_FSL_USB_PLLPRG2_MFI | CONFIG_SYS_FSL_USB_PLLPRG2_PLL_EN); +#ifdef CONFIG_SYS_FSL_SINGLE_SOURCE_CLK + usb_single_source_clk_configure(usb_phy); +#endif setbits_be32(&usb_phy->port1.ctrl, CONFIG_SYS_FSL_USB_CTRL_PHY_EN); setbits_be32(&usb_phy->port1.drvvbuscfg, @@ -767,8 +892,6 @@ skip_l2: return 0; } -extern void setup_ivors(void); - void arch_preboot_os(void) { u32 msr; @@ -781,8 +904,6 @@ void arch_preboot_os(void) msr = mfmsr(); msr &= ~(MSR_ME|MSR_CE); mtmsr(msr); - - setup_ivors(); } #if defined(CONFIG_CMD_SATA) && defined(CONFIG_FSL_SATA) @@ -797,21 +918,13 @@ int sata_initialize(void) void cpu_secondary_init_r(void) { -#ifdef CONFIG_QE +#ifdef CONFIG_U_QE + uint qe_base = CONFIG_SYS_IMMR + 0x00140000; /* QE immr base */ +#elif defined CONFIG_QE uint qe_base = CONFIG_SYS_IMMR + 0x00080000; /* QE immr base */ -#ifdef CONFIG_SYS_QE_FMAN_FW_IN_NAND - int ret; - size_t fw_length = CONFIG_SYS_QE_FMAN_FW_LENGTH; - - /* load QE firmware from NAND flash to DDR first */ - ret = nand_read(&nand_info[0], (loff_t)CONFIG_SYS_QE_FMAN_FW_IN_NAND, - &fw_length, (u_char *)CONFIG_SYS_QE_FMAN_FW_ADDR); - - if (ret && ret == -EUCLEAN) { - printf ("NAND read for QE firmware at offset %x failed %d\n", - CONFIG_SYS_QE_FMAN_FW_IN_NAND, ret); - } #endif + +#ifdef CONFIG_QE qe_init(qe_base); qe_reset(); #endif |