diff options
Diffstat (limited to 'arch/powerpc/cpu/mpc8xxx/ddr/main.c')
| -rw-r--r-- | arch/powerpc/cpu/mpc8xxx/ddr/main.c | 65 |
1 files changed, 56 insertions, 9 deletions
diff --git a/arch/powerpc/cpu/mpc8xxx/ddr/main.c b/arch/powerpc/cpu/mpc8xxx/ddr/main.c index 7a8636de16..842bf1989e 100644 --- a/arch/powerpc/cpu/mpc8xxx/ddr/main.c +++ b/arch/powerpc/cpu/mpc8xxx/ddr/main.c @@ -25,10 +25,6 @@ void fsl_ddr_set_lawbar( unsigned int ctrl_num); void fsl_ddr_set_intl3r(const unsigned int granule_size); -/* processor specific function */ -extern void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs, - unsigned int ctrl_num); - #if defined(SPD_EEPROM_ADDRESS) || \ defined(SPD_EEPROM_ADDRESS1) || defined(SPD_EEPROM_ADDRESS2) || \ defined(SPD_EEPROM_ADDRESS3) || defined(SPD_EEPROM_ADDRESS4) @@ -365,9 +361,11 @@ fsl_ddr_compute(fsl_ddr_info_t *pinfo, unsigned int start_step, { unsigned int i, j; unsigned long long total_mem = 0; + int assert_reset; fsl_ddr_cfg_regs_t *ddr_reg = pinfo->fsl_ddr_config_reg; common_timing_params_t *timing_params = pinfo->common_timing_params; + assert_reset = board_need_mem_reset(); /* data bus width capacity adjust shift amount */ unsigned int dbw_capacity_adjust[CONFIG_NUM_DDR_CONTROLLERS]; @@ -462,7 +460,20 @@ fsl_ddr_compute(fsl_ddr_info_t *pinfo, unsigned int start_step, timing_params[i].all_DIMMs_registered, &pinfo->memctl_opts[i], pinfo->dimm_params[i], i); + /* + * For RDIMMs, JEDEC spec requires clocks to be stable + * before reset signal is deasserted. For the boards + * using fixed parameters, this function should be + * be called from board init file. + */ + if (timing_params[i].all_DIMMs_registered) + assert_reset = 1; } + if (assert_reset) { + debug("Asserting mem reset\n"); + board_assert_mem_reset(); + } + case STEP_ASSIGN_ADDRESSES: /* STEP 5: Assign addresses to chip selects */ check_interleaving_options(pinfo); @@ -504,7 +515,13 @@ fsl_ddr_compute(fsl_ddr_info_t *pinfo, unsigned int start_step, fsl_ddr_cfg_regs_t *reg = &ddr_reg[i]; if (reg->cs[j].config & 0x80000000) { unsigned int end; - end = reg->cs[j].bnds & 0xFFF; + /* + * 0xfffffff is a special value we put + * for unused bnds + */ + if (reg->cs[j].bnds == 0xffffffff) + continue; + end = reg->cs[j].bnds & 0xffff; if (end > max_end) { max_end = end; } @@ -531,6 +548,7 @@ phys_size_t fsl_ddr_sdram(void) unsigned int law_memctl = LAW_TRGT_IF_DDR_1; unsigned long long total_memory; fsl_ddr_info_t info; + int deassert_reset; /* Reset info structure. */ memset(&info, 0, sizeof(fsl_ddr_info_t)); @@ -559,7 +577,21 @@ phys_size_t fsl_ddr_sdram(void) } } - /* Program configuration registers. */ + /* + * Program configuration registers. + * JEDEC specs requires clocks to be stable before deasserting reset + * for RDIMMs. Clocks start after chip select is enabled and clock + * control register is set. During step 1, all controllers have their + * registers set but not enabled. Step 2 proceeds after deasserting + * reset through board FPGA or GPIO. + * For non-registered DIMMs, initialization can go through but it is + * also OK to follow the same flow. + */ + deassert_reset = board_need_mem_reset(); + for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { + if (info.common_timing_params[i].all_DIMMs_registered) + deassert_reset = 1; + } for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { debug("Programming controller %u\n", i); if (info.common_timing_params[i].ndimms_present == 0) { @@ -567,8 +599,22 @@ phys_size_t fsl_ddr_sdram(void) "skipping programming\n", i); continue; } - - fsl_ddr_set_memctl_regs(&(info.fsl_ddr_config_reg[i]), i); + /* + * The following call with step = 1 returns before enabling + * the controller. It has to finish with step = 2 later. + */ + fsl_ddr_set_memctl_regs(&(info.fsl_ddr_config_reg[i]), i, + deassert_reset ? 1 : 0); + } + if (deassert_reset) { + /* Use board FPGA or GPIO to deassert reset signal */ + debug("Deasserting mem reset\n"); + board_deassert_mem_reset(); + for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { + /* Call with step = 2 to continue initialization */ + fsl_ddr_set_memctl_regs(&(info.fsl_ddr_config_reg[i]), + i, 2); + } } /* program LAWs */ @@ -637,7 +683,8 @@ phys_size_t fsl_ddr_sdram(void) #if !defined(CONFIG_PHYS_64BIT) /* Check for 4G or more. Bad. */ if (total_memory >= (1ull << 32)) { - printf("Detected %lld MB of memory\n", total_memory >> 20); + puts("Detected "); + print_size(total_memory, " of memory\n"); printf(" This U-Boot only supports < 4G of DDR\n"); printf(" You could rebuild it with CONFIG_PHYS_64BIT\n"); printf(" "); /* re-align to match init_func_ram print */ |