diff options
Diffstat (limited to 'arch')
| -rw-r--r-- | arch/x86/Kconfig | 38 | ||||
| -rw-r--r-- | arch/x86/cpu/queensbay/Kconfig | 38 |
2 files changed, 38 insertions, 38 deletions
diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig index 928fc60863..c2af607ca6 100644 --- a/arch/x86/Kconfig +++ b/arch/x86/Kconfig @@ -344,6 +344,44 @@ config TSC_FREQ_IN_MHZ help The running frequency in MHz of Time-Stamp Counter (TSC). +config HAVE_FSP + bool "Add an Firmware Support Package binary" + help + Select this option to add an Firmware Support Package binary to + the resulting U-Boot image. It is a binary blob which U-Boot uses + to set up SDRAM and other chipset specific initialization. + + Note: Without this binary U-Boot will not be able to set up its + SDRAM so will not boot. + +config FSP_FILE + string "Firmware Support Package binary filename" + depends on HAVE_FSP + default "fsp.bin" + help + The filename of the file to use as Firmware Support Package binary + in the board directory. + +config FSP_ADDR + hex "Firmware Support Package binary location" + depends on HAVE_FSP + default 0xfffc0000 + help + FSP is not Position Independent Code (PIC) and the whole FSP has to + be rebased if it is placed at a location which is different from the + perferred base address specified during the FSP build. Use Intel's + Binary Configuration Tool (BCT) to do the rebase. + + The default base address of 0xfffc0000 indicates that the binary must + be located at offset 0xc0000 from the beginning of a 1MB flash device. + +config FSP_TEMP_RAM_ADDR + hex + default 0x2000000 + help + Stack top address which is used in FspInit after DRAM is ready and + CAR is disabled. + source "arch/x86/cpu/coreboot/Kconfig" source "arch/x86/cpu/ivybridge/Kconfig" diff --git a/arch/x86/cpu/queensbay/Kconfig b/arch/x86/cpu/queensbay/Kconfig index f6b52010c3..397e599f93 100644 --- a/arch/x86/cpu/queensbay/Kconfig +++ b/arch/x86/cpu/queensbay/Kconfig @@ -11,44 +11,6 @@ config INTEL_QUEENSBAY if INTEL_QUEENSBAY -config HAVE_FSP - bool "Add an Firmware Support Package binary" - help - Select this option to add an Firmware Support Package binary to - the resulting U-Boot image. It is a binary blob which U-Boot uses - to set up SDRAM and other chipset specific initialization. - - Note: Without this binary U-Boot will not be able to set up its - SDRAM so will not boot. - -config FSP_FILE - string "Firmware Support Package binary filename" - depends on HAVE_FSP - default "fsp.bin" - help - The filename of the file to use as Firmware Support Package binary - in the board directory. - -config FSP_ADDR - hex "Firmware Support Package binary location" - depends on HAVE_FSP - default 0xfffc0000 - help - FSP is not Position Independent Code (PIC) and the whole FSP has to - be rebased if it is placed at a location which is different from the - perferred base address specified during the FSP build. Use Intel's - Binary Configuration Tool (BCT) to do the rebase. - - The default base address of 0xfffc0000 indicates that the binary must - be located at offset 0xc0000 from the beginning of a 1MB flash device. - -config FSP_TEMP_RAM_ADDR - hex - default 0x2000000 - help - Stack top address which is used in FspInit after DRAM is ready and - CAR is disabled. - config HAVE_CMC bool "Add a Chipset Micro Code state machine binary" help |