diff options
Diffstat (limited to 'arch')
56 files changed, 10368 insertions, 369 deletions
diff --git a/arch/powerpc/Kconfig b/arch/powerpc/Kconfig index 0b1629ba62..c2c577f60c 100644 --- a/arch/powerpc/Kconfig +++ b/arch/powerpc/Kconfig @@ -39,6 +39,12 @@ config MPC8xx endchoice +config HIGH_BATS + bool "Enable high BAT registers" + help + Enable BATs (block address translation registers) 4-7 on machines + that support them. + source "arch/powerpc/cpu/mpc83xx/Kconfig" source "arch/powerpc/cpu/mpc85xx/Kconfig" source "arch/powerpc/cpu/mpc86xx/Kconfig" diff --git a/arch/powerpc/cpu/mpc83xx/Kconfig b/arch/powerpc/cpu/mpc83xx/Kconfig index 571cf8fc2e..b99288aa83 100644 --- a/arch/powerpc/cpu/mpc83xx/Kconfig +++ b/arch/powerpc/cpu/mpc83xx/Kconfig @@ -10,38 +10,66 @@ choice config TARGET_MPC8308_P1M bool "Support mpc8308_p1m" + select ARCH_MPC8308 config TARGET_SBC8349 bool "Support sbc8349" + select ARCH_MPC8349 config TARGET_VE8313 bool "Support ve8313" + select ARCH_MPC8313 config TARGET_VME8349 bool "Support vme8349" + select ARCH_MPC8349 + +config TARGET_CADDY2 + bool "Support caddy2" + select ARCH_MPC8349 config TARGET_MPC8308RDB bool "Support MPC8308RDB" + select ARCH_MPC8308 select SYS_FSL_ERRATUM_ESDHC111 -config TARGET_MPC8313ERDB - bool "Support MPC8313ERDB" +config TARGET_MPC8313ERDB_NOR + bool "Support MPC8313ERDB_NOR" + select ARCH_MPC8313 + select BOARD_EARLY_INIT_F + select SUPPORT_SPL + +config TARGET_MPC8313ERDB_NAND + bool "Support MPC8313ERDB_NAND" + select ARCH_MPC8313 select BOARD_EARLY_INIT_F select SUPPORT_SPL config TARGET_MPC8315ERDB bool "Support MPC8315ERDB" + select ARCH_MPC8315 select BOARD_EARLY_INIT_F config TARGET_MPC8323ERDB bool "Support MPC8323ERDB" + select ARCH_MPC832X config TARGET_MPC832XEMDS bool "Support MPC832XEMDS" + select ARCH_MPC832X select BOARD_EARLY_INIT_F config TARGET_MPC8349EMDS bool "Support MPC8349EMDS" + select ARCH_MPC8349 + select BOARD_EARLY_INIT_F + select SYS_FSL_DDR + select SYS_FSL_DDR_BE + select SYS_FSL_HAS_DDR2 + +config TARGET_MPC8349EMDS_SDRAM + bool "Support MPC8349EMDS_SDRAM" + select ARCH_MPC8349 select BOARD_EARLY_INIT_F select SYS_FSL_DDR select SYS_FSL_DDR_BE @@ -49,53 +77,272 @@ config TARGET_MPC8349EMDS config TARGET_MPC8349ITX bool "Support MPC8349ITX" + select ARCH_MPC8349 imply CMD_IRQ config TARGET_MPC837XEMDS bool "Support MPC837XEMDS" + select ARCH_MPC837X select BOARD_EARLY_INIT_F imply CMD_SATA imply FSL_SATA config TARGET_MPC837XERDB bool "Support MPC837XERDB" + select ARCH_MPC837X select BOARD_EARLY_INIT_F config TARGET_IDS8313 bool "Support ids8313" + select ARCH_MPC8313 select DM imply CMD_DM -config TARGET_KM8360 - bool "Support km8360" +config TARGET_KMETER1 + bool "Support kmeter1" + select ARCH_MPC8360 + imply CMD_CRAMFS + imply CMD_DIAG + imply FS_CRAMFS + +config TARGET_KMCOGE5NE + bool "Support kmcoge5ne" + select ARCH_MPC8360 imply CMD_CRAMFS imply CMD_DIAG imply FS_CRAMFS config TARGET_SUVD3 bool "Support suvd3" + select ARCH_MPC832X + imply CMD_CRAMFS + imply FS_CRAMFS + +config TARGET_KMVECT1 + bool "Support kmvect1" + select ARCH_MPC8309 + imply CMD_CRAMFS + imply FS_CRAMFS + +config TARGET_KMTEGR1 + bool "Support kmtegr1" + select ARCH_MPC8309 imply CMD_CRAMFS imply FS_CRAMFS config TARGET_TUXX1 bool "Support tuxx1" + select ARCH_MPC832X + imply CMD_CRAMFS + imply FS_CRAMFS + +config TARGET_KMSUPX5 + bool "Support kmsupx5" + select ARCH_MPC832X + imply CMD_CRAMFS + imply FS_CRAMFS + +config TARGET_TUGE1 + bool "Support tuge1" + select ARCH_MPC832X + imply CMD_CRAMFS + imply FS_CRAMFS + +config TARGET_KMOPTI2 + bool "Support kmopti2" + select ARCH_MPC832X + imply CMD_CRAMFS + imply FS_CRAMFS + +config TARGET_KMTEPR2 + bool "Support kmtepr2" + select ARCH_MPC832X imply CMD_CRAMFS imply FS_CRAMFS config TARGET_TQM834X bool "Support TQM834x" + select ARCH_MPC8349 config TARGET_HRCON bool "Support hrcon" + select ARCH_MPC8308 select SYS_FSL_ERRATUM_ESDHC111 config TARGET_STRIDER bool "Support strider" + select ARCH_MPC8308 select SYS_FSL_ERRATUM_ESDHC111 imply CMD_PCA953X +config TARGET_GAZERBEAM + bool "Support gazerbeam" + select ARCH_MPC8308 + select SYS_FSL_ERRATUM_ESDHC111 + imply ENV_IS_IN_FLASH + help + The "Gazerbeam" is a modular system by Guntermann & Drunck GmbH + Systementwicklung based on the NXP MPC8308 SoC for usage in KVM + appliances. + + Features include: + * Two gigabit ethernet ports + * Multiple USB ports (depending on variant) + * Several gigabit ethernet or optical fiber ports (depending on + variant) + * Several display port inputs and outputs, and supporting redrivers + (depending on variant) + * Several FPGAs with custom logic (depending on variant) + +endchoice + +config MPC83XX_QUICC_ENGINE + bool + +# TODO: Imply MPC83xx PCI driver +config MPC83XX_PCI_SUPPORT + bool + +# TODO: Imply TSEC driver +config MPC83XX_TSEC1_SUPPORT + bool + +config MPC83XX_TSEC2_SUPPORT + bool + +config MPC83XX_PCIE1_SUPPORT + bool + +config MPC83XX_PCIE2_SUPPORT + bool + +config MPC83XX_SDHC_SUPPORT + bool + +config MPC83XX_SATA_SUPPORT + bool + +config MPC83XX_SECOND_I2C_SUPPORT + bool + +config MPC83XX_LDP_PIN + bool + +config ARCH_MPC830X + bool + select MPC83XX_SDHC_SUPPORT + +config ARCH_MPC8308 + bool + select ARCH_MPC830X + select MPC83XX_TSEC1_SUPPORT + select MPC83XX_TSEC2_SUPPORT + select MPC83XX_PCIE1_SUPPORT + select MPC83XX_SECOND_I2C_SUPPORT + +config ARCH_MPC8309 + bool + select ARCH_MPC830X + select MPC83XX_QUICC_ENGINE + select MPC83XX_PCI_SUPPORT + select MPC83XX_SECOND_I2C_SUPPORT + +config ARCH_MPC831X + bool + select MPC83XX_PCI_SUPPORT + select MPC83XX_TSEC1_SUPPORT + select MPC83XX_TSEC2_SUPPORT + +config ARCH_MPC8313 + bool + select ARCH_MPC831X + select MPC83XX_SECOND_I2C_SUPPORT + +config ARCH_MPC8315 + bool + select ARCH_MPC831X + select MPC83XX_PCIE1_SUPPORT + select MPC83XX_PCIE2_SUPPORT + select MPC83XX_SATA_SUPPORT + +config ARCH_MPC832X + bool + select MPC83XX_QUICC_ENGINE + select MPC83XX_PCI_SUPPORT + +config ARCH_MPC834X + bool + +config ARCH_MPC8349 + bool + select ARCH_MPC834X + select MPC83XX_PCI_SUPPORT + select MPC83XX_TSEC1_SUPPORT + select MPC83XX_TSEC2_SUPPORT + select MPC83XX_LDP_PIN + select MPC83XX_SECOND_I2C_SUPPORT + +config ARCH_MPC8360 + bool + select MPC83XX_QUICC_ENGINE + select MPC83XX_PCI_SUPPORT + select MPC83XX_LDP_PIN + select MPC83XX_SECOND_I2C_SUPPORT + +config ARCH_MPC837X + bool + select MPC83XX_PCI_SUPPORT + select MPC83XX_TSEC1_SUPPORT + select MPC83XX_TSEC2_SUPPORT + select MPC83XX_PCIE1_SUPPORT + select MPC83XX_PCIE2_SUPPORT + select MPC83XX_SDHC_SUPPORT + select MPC83XX_SATA_SUPPORT + select MPC83XX_LDP_PIN + select MPC83XX_SECOND_I2C_SUPPORT + +config SYS_IMMR + hex "Value for IMMR" + default 0xE0000000 + help + Address for the Internal Memory-Mapped Registers (IMMR) window used + to configure the features of the SoC. + +source "arch/powerpc/cpu/mpc83xx/hrcw/Kconfig" +source "arch/powerpc/cpu/mpc83xx/bats/Kconfig" +source "arch/powerpc/cpu/mpc83xx/lblaw/Kconfig" +source "arch/powerpc/cpu/mpc83xx/elbc/Kconfig" +source "arch/powerpc/cpu/mpc83xx/hid/Kconfig" +source "arch/powerpc/cpu/mpc83xx/sysio/Kconfig" +source "arch/powerpc/cpu/mpc83xx/arbiter/Kconfig" +source "arch/powerpc/cpu/mpc83xx/initreg/Kconfig" + +menu "Legacy options" + +if ARCH_MPC8349 + +#TODO(mario.six@gdsys.cc): Remove when mpc83xx PCI has been converted to DM/DT +choice + prompt "PMC slot configuration" + +config PCI_ALL_PCI1 + bool "All PMC slots on PCI1" + +config PCI_ONE_PCI1 + bool "First PMC1 on PCI1" + +config PCI_TWO_PCI1 + bool "First two PMC1 on PCI1" + endchoice +config PCI_64BIT + bool "PMC2 is 64bit" + +endif + +endmenu + source "board/esd/vme8349/Kconfig" source "board/freescale/mpc8308rdb/Kconfig" source "board/freescale/mpc8313erdb/Kconfig" diff --git a/arch/powerpc/cpu/mpc83xx/Makefile b/arch/powerpc/cpu/mpc83xx/Makefile index aa4affa911..304029977e 100644 --- a/arch/powerpc/cpu/mpc83xx/Makefile +++ b/arch/powerpc/cpu/mpc83xx/Makefile @@ -29,7 +29,9 @@ obj-y += interrupts.o obj-y += ecc.o obj-$(CONFIG_QE) += qe_io.o obj-$(CONFIG_FSL_SERDES) += serdes.o +ifndef CONFIG_ARCH_MPC8308 obj-$(CONFIG_PCI) += pci.o +endif obj-$(CONFIG_PCIE) += pcie.o obj-$(CONFIG_OF_LIBFDT) += fdt.o diff --git a/arch/powerpc/cpu/mpc83xx/arbiter/Kconfig b/arch/powerpc/cpu/mpc83xx/arbiter/Kconfig new file mode 100644 index 0000000000..f562476da8 --- /dev/null +++ b/arch/powerpc/cpu/mpc83xx/arbiter/Kconfig @@ -0,0 +1,139 @@ +menu "Arbiter" + +choice + prompt "Pipeline depth" + +config ACR_PIPE_DEP_UNSET + bool "Don't set value" + +config ACR_PIPE_DEP_1 + bool "1" + +config ACR_PIPE_DEP_2 + bool "2" + +config ACR_PIPE_DEP_3 + bool "3" + +config ACR_PIPE_DEP_4 + bool "4" + +endchoice + +choice + prompt "Repeat count" + +config ACR_RPTCNT_UNSET + bool "Don't set value" + +config ACR_RPTCNT_1 + bool "1" + +config ACR_RPTCNT_2 + bool "2" + +config ACR_RPTCNT_3 + bool "3" + +config ACR_RPTCNT_4 + bool "4" + +config ACR_RPTCNT_5 + bool "5" + +config ACR_RPTCNT_6 + bool "6" + +config ACR_RPTCNT_7 + bool "7" + +config ACR_RPTCNT_8 + bool "8" + +endchoice + +choice + prompt "Address parking" + +config ACR_APARK_UNSET + bool "Don't set value" + +config ACR_APARK_MASTER + bool "Park to master" + +config ACR_APARK_LAST + bool "Park to last owner" + +config ACR_APARK_DISABLE + bool "Disabled" + +endchoice + +choice + prompt "Parking master" + +config ACR_PARKM_UNSET + bool "Don't set value" + +config ACR_PARKM_E300 + bool "e300 core" + +config ACR_PARKM_TSEC_1_2 + bool "TSEC1, TSEC2" + +config ACR_PARKM_USB_I2C1_BOOT + bool "USB/I2C1_BOOT" + +config ACR_PARKM_DMA_ESDHC_USB + bool "DMA, ESDHC, USB" + +config ACR_PARKM_PEX + bool "PCI Express" + +if MPC83XX_QUICC_ENGINE + +config ACR_PARKM_ENC_CORE + bool "Encryption core" + +endif + +endchoice + +config ACR_PIPE_DEP + hex + default 0x0 if ACR_PIPE_DEP_UNSET + default 0x0 if ACR_PIPE_DEP_1 + default 0x10000 if ACR_PIPE_DEP_2 + default 0x20000 if ACR_PIPE_DEP_3 + default 0x30000 if ACR_PIPE_DEP_4 + +config ACR_RPTCNT + hex + default 0x0 if ACR_RPTCNT_UNSET + default 0x0 if ACR_RPTCNT_1 + default 0x100 if ACR_RPTCNT_2 + default 0x200 if ACR_RPTCNT_3 + default 0x300 if ACR_RPTCNT_4 + default 0x400 if ACR_RPTCNT_5 + default 0x500 if ACR_RPTCNT_6 + default 0x600 if ACR_RPTCNT_7 + default 0x700 if ACR_RPTCNT_8 + +config ACR_APARK + hex + default 0x0 if ACR_APARK_UNSET + default 0x0 if ACR_APARK_MASTER + default 0x10 if ACR_APARK_LAST + default 0x20 if ACR_APARK_DISABLE + +config ACR_PARKM + hex + default 0x0 if ACR_PARKM_UNSET + default 0x0 if ACR_PARKM_E300 + default 0x2 if ACR_PARKM_TSEC_1_2 + default 0x3 if ACR_PARKM_USB_I2C1_BOOT + default 0x4 if ACR_PARKM_DMA_ESDHC_USB + default 0x5 if ACR_PARKM_PEX + default 0x5 if ACR_PARKM_ENC_CORE + +endmenu diff --git a/arch/powerpc/cpu/mpc83xx/arbiter/arbiter.h b/arch/powerpc/cpu/mpc83xx/arbiter/arbiter.h new file mode 100644 index 0000000000..10a47e4987 --- /dev/null +++ b/arch/powerpc/cpu/mpc83xx/arbiter/arbiter.h @@ -0,0 +1,28 @@ + const __be32 acr_mask = +#ifndef CONFIG_ACR_PIPE_DEP_UNSET + ACR_PIPE_DEP | +#endif +#ifndef CONFIG_ACR_RPTCNT_UNSET + ACR_RPTCNT | +#endif +#ifndef CONFIG_ACR_APARK_UNSET + ACR_APARK | +#endif +#ifndef CONFIG_ACR_PARKM_UNSET + ACR_PARKM | +#endif + 0; + const __be32 acr_val = +#ifndef CONFIG_ACR_PIPE_DEP_UNSET + CONFIG_ACR_PIPE_DEP | +#endif +#ifndef CONFIG_ACR_RPTCNT_UNSET + CONFIG_ACR_RPTCNT | +#endif +#ifndef CONFIG_ACR_APARK_UNSET + CONFIG_ACR_APARK | +#endif +#ifndef CONFIG_ACR_PARKM_UNSET + CONFIG_ACR_PARKM | +#endif + 0; diff --git a/arch/powerpc/cpu/mpc83xx/bats/Kconfig b/arch/powerpc/cpu/mpc83xx/bats/Kconfig new file mode 100644 index 0000000000..218920cfc9 --- /dev/null +++ b/arch/powerpc/cpu/mpc83xx/bats/Kconfig @@ -0,0 +1,1311 @@ +menu "BATS setup" + +menuconfig BAT0 + bool "BAT0" + +if BAT0 + +config BAT0_NAME + string "Identifier" + +config BAT0_BASE + hex "Base" + +choice + prompt "Block length" + +config BAT0_LENGTH_128_KBYTES + bool "128 kb" + +config BAT0_LENGTH_256_KBYTES + bool "256 kb" + +config BAT0_LENGTH_512_KBYTES + bool "512 kb" + +config BAT0_LENGTH_1_MBYTES + bool "1 mb" + +config BAT0_LENGTH_2_MBYTES + bool "2 mb" + +config BAT0_LENGTH_4_MBYTES + bool "4 mb" + +config BAT0_LENGTH_8_MBYTES + bool "8 mb" + +config BAT0_LENGTH_16_MBYTES + bool "16 mb" + +config BAT0_LENGTH_32_MBYTES + bool "32 mb" + +config BAT0_LENGTH_64_MBYTES + bool "64 mb" + +config BAT0_LENGTH_128_MBYTES + bool "128 mb" + +config BAT0_LENGTH_256_MBYTES + bool "256 mb" +endchoice + +choice + prompt "Protection mode" + +config BAT0_ACCESS_NONE + bool "No access" + +config BAT0_ACCESS_RO + bool "Read-only" + +config BAT0_ACCESS_RW + bool "Read-write" + +endchoice + +config BAT0_ICACHE_WRITETHROUGH + bool "I-cache Write-through" + +config BAT0_ICACHE_INHIBITED + bool "I-cache Inhibited" + +config BAT0_ICACHE_MEMORYCOHERENCE + bool "I-cache Memory coherence" + +config BAT0_ICACHE_GUARDED + bool "I-cache Guarded" + +config BAT0_DCACHE_WRITETHROUGH + bool "D-cache Write-through" + +config BAT0_DCACHE_INHIBITED + bool "D-cache Inhibited" + +config BAT0_DCACHE_MEMORYCOHERENCE + bool "D-cache Memory coherence" + +config BAT0_DCACHE_GUARDED + bool "D-cache Guarded" + +config BAT0_USER_MODE_VALID + bool "User mode valid" + +config BAT0_SUPERVISOR_MODE_VALID + bool "Supervisor mode valid" + +endif + +config BAT0_LENGTH + hex + default 0x00000000 if BAT0_LENGTH_128_KBYTES + default 0x00000004 if BAT0_LENGTH_256_KBYTES + default 0x0000000c if BAT0_LENGTH_512_KBYTES + default 0x0000001c if BAT0_LENGTH_1_MBYTES + default 0x0000003c if BAT0_LENGTH_2_MBYTES + default 0x0000007c if BAT0_LENGTH_4_MBYTES + default 0x000000fc if BAT0_LENGTH_8_MBYTES + default 0x000001fc if BAT0_LENGTH_16_MBYTES + default 0x000003fc if BAT0_LENGTH_32_MBYTES + default 0x000007fc if BAT0_LENGTH_64_MBYTES + default 0x00000ffc if BAT0_LENGTH_128_MBYTES + default 0x00001ffc if BAT0_LENGTH_256_MBYTES + +config BAT0_PAGE_PROTECTION + hex + default 0x0 if BAT0_ACCESS_NONE + default 0x1 if BAT0_ACCESS_RO + default 0x2 if BAT0_ACCESS_RW + +config BAT0_WIMG_ICACHE + hex + default 0x0 if !BAT0_ICACHE_WRITETHROUGH && !BAT0_ICACHE_INHIBITED && !BAT0_ICACHE_MEMORYCOHERENCE && !BAT0_ICACHE_GUARDED + default 0x8 if !BAT0_ICACHE_WRITETHROUGH && !BAT0_ICACHE_INHIBITED && !BAT0_ICACHE_MEMORYCOHERENCE && BAT0_ICACHE_GUARDED + default 0x10 if !BAT0_ICACHE_WRITETHROUGH && !BAT0_ICACHE_INHIBITED && BAT0_ICACHE_MEMORYCOHERENCE && !BAT0_ICACHE_GUARDED + default 0x18 if !BAT0_ICACHE_WRITETHROUGH && !BAT0_ICACHE_INHIBITED && BAT0_ICACHE_MEMORYCOHERENCE && BAT0_ICACHE_GUARDED + default 0x20 if !BAT0_ICACHE_WRITETHROUGH && BAT0_ICACHE_INHIBITED && !BAT0_ICACHE_MEMORYCOHERENCE && !BAT0_ICACHE_GUARDED + default 0x28 if !BAT0_ICACHE_WRITETHROUGH && BAT0_ICACHE_INHIBITED && !BAT0_ICACHE_MEMORYCOHERENCE && BAT0_ICACHE_GUARDED + default 0x30 if !BAT0_ICACHE_WRITETHROUGH && BAT0_ICACHE_INHIBITED && BAT0_ICACHE_MEMORYCOHERENCE && !BAT0_ICACHE_GUARDED + default 0x38 if !BAT0_ICACHE_WRITETHROUGH && BAT0_ICACHE_INHIBITED && BAT0_ICACHE_MEMORYCOHERENCE && BAT0_ICACHE_GUARDED + default 0x40 if BAT0_ICACHE_WRITETHROUGH && !BAT0_ICACHE_INHIBITED && !BAT0_ICACHE_MEMORYCOHERENCE && !BAT0_ICACHE_GUARDED + default 0x48 if BAT0_ICACHE_WRITETHROUGH && !BAT0_ICACHE_INHIBITED && !BAT0_ICACHE_MEMORYCOHERENCE && BAT0_ICACHE_GUARDED + default 0x50 if BAT0_ICACHE_WRITETHROUGH && !BAT0_ICACHE_INHIBITED && BAT0_ICACHE_MEMORYCOHERENCE && !BAT0_ICACHE_GUARDED + default 0x58 if BAT0_ICACHE_WRITETHROUGH && !BAT0_ICACHE_INHIBITED && BAT0_ICACHE_MEMORYCOHERENCE && BAT0_ICACHE_GUARDED + default 0x60 if BAT0_ICACHE_WRITETHROUGH && BAT0_ICACHE_INHIBITED && !BAT0_ICACHE_MEMORYCOHERENCE && !BAT0_ICACHE_GUARDED + default 0x68 if BAT0_ICACHE_WRITETHROUGH && BAT0_ICACHE_INHIBITED && !BAT0_ICACHE_MEMORYCOHERENCE && BAT0_ICACHE_GUARDED + default 0x70 if BAT0_ICACHE_WRITETHROUGH && BAT0_ICACHE_INHIBITED && BAT0_ICACHE_MEMORYCOHERENCE && !BAT0_ICACHE_GUARDED + default 0x78 if BAT0_ICACHE_WRITETHROUGH && BAT0_ICACHE_INHIBITED && BAT0_ICACHE_MEMORYCOHERENCE && BAT0_ICACHE_GUARDED + +config BAT0_WIMG_DCACHE + hex + default 0x0 if !BAT0_DCACHE_WRITETHROUGH && !BAT0_DCACHE_INHIBITED && !BAT0_DCACHE_MEMORYCOHERENCE && !BAT0_DCACHE_GUARDED + default 0x8 if !BAT0_DCACHE_WRITETHROUGH && !BAT0_DCACHE_INHIBITED && !BAT0_DCACHE_MEMORYCOHERENCE && BAT0_DCACHE_GUARDED + default 0x10 if !BAT0_DCACHE_WRITETHROUGH && !BAT0_DCACHE_INHIBITED && BAT0_DCACHE_MEMORYCOHERENCE && !BAT0_DCACHE_GUARDED + default 0x18 if !BAT0_DCACHE_WRITETHROUGH && !BAT0_DCACHE_INHIBITED && BAT0_DCACHE_MEMORYCOHERENCE && BAT0_DCACHE_GUARDED + default 0x20 if !BAT0_DCACHE_WRITETHROUGH && BAT0_DCACHE_INHIBITED && !BAT0_DCACHE_MEMORYCOHERENCE && !BAT0_DCACHE_GUARDED + default 0x28 if !BAT0_DCACHE_WRITETHROUGH && BAT0_DCACHE_INHIBITED && !BAT0_DCACHE_MEMORYCOHERENCE && BAT0_DCACHE_GUARDED + default 0x30 if !BAT0_DCACHE_WRITETHROUGH && BAT0_DCACHE_INHIBITED && BAT0_DCACHE_MEMORYCOHERENCE && !BAT0_DCACHE_GUARDED + default 0x38 if !BAT0_DCACHE_WRITETHROUGH && BAT0_DCACHE_INHIBITED && BAT0_DCACHE_MEMORYCOHERENCE && BAT0_DCACHE_GUARDED + default 0x40 if BAT0_DCACHE_WRITETHROUGH && !BAT0_DCACHE_INHIBITED && !BAT0_DCACHE_MEMORYCOHERENCE && !BAT0_DCACHE_GUARDED + default 0x48 if BAT0_DCACHE_WRITETHROUGH && !BAT0_DCACHE_INHIBITED && !BAT0_DCACHE_MEMORYCOHERENCE && BAT0_DCACHE_GUARDED + default 0x50 if BAT0_DCACHE_WRITETHROUGH && !BAT0_DCACHE_INHIBITED && BAT0_DCACHE_MEMORYCOHERENCE && !BAT0_DCACHE_GUARDED + default 0x58 if BAT0_DCACHE_WRITETHROUGH && !BAT0_DCACHE_INHIBITED && BAT0_DCACHE_MEMORYCOHERENCE && BAT0_DCACHE_GUARDED + default 0x60 if BAT0_DCACHE_WRITETHROUGH && BAT0_DCACHE_INHIBITED && !BAT0_DCACHE_MEMORYCOHERENCE && !BAT0_DCACHE_GUARDED + default 0x68 if BAT0_DCACHE_WRITETHROUGH && BAT0_DCACHE_INHIBITED && !BAT0_DCACHE_MEMORYCOHERENCE && BAT0_DCACHE_GUARDED + default 0x70 if BAT0_DCACHE_WRITETHROUGH && BAT0_DCACHE_INHIBITED && BAT0_DCACHE_MEMORYCOHERENCE && !BAT0_DCACHE_GUARDED + default 0x78 if BAT0_DCACHE_WRITETHROUGH && BAT0_DCACHE_INHIBITED && BAT0_DCACHE_MEMORYCOHERENCE && BAT0_DCACHE_GUARDED + +config BAT0_VALID_BITS + hex + default 0x0 if !BAT0_SUPERVISOR_MODE_VALID && !BAT0_USER_MODE_VALID + default 0x1 if !BAT0_SUPERVISOR_MODE_VALID && BAT0_USER_MODE_VALID + default 0x2 if BAT0_SUPERVISOR_MODE_VALID && !BAT0_USER_MODE_VALID + default 0x3 if BAT0_SUPERVISOR_MODE_VALID && BAT0_USER_MODE_VALID + +menuconfig BAT1 + bool "BAT1" + +if BAT1 + +config BAT1_NAME + string "Identifier" + +config BAT1_BASE + hex "Base" + +choice + prompt "Block length" + +config BAT1_LENGTH_128_KBYTES + bool "128 kb" + +config BAT1_LENGTH_256_KBYTES + bool "256 kb" + +config BAT1_LENGTH_512_KBYTES + bool "512 kb" + +config BAT1_LENGTH_1_MBYTES + bool "1 mb" + +config BAT1_LENGTH_2_MBYTES + bool "2 mb" + +config BAT1_LENGTH_4_MBYTES + bool "4 mb" + +config BAT1_LENGTH_8_MBYTES + bool "8 mb" + +config BAT1_LENGTH_16_MBYTES + bool "16 mb" + +config BAT1_LENGTH_32_MBYTES + bool "32 mb" + +config BAT1_LENGTH_64_MBYTES + bool "64 mb" + +config BAT1_LENGTH_128_MBYTES + bool "128 mb" + +config BAT1_LENGTH_256_MBYTES + bool "256 mb" +endchoice + +choice + prompt "Protection mode" + +config BAT1_ACCESS_NONE + bool "No access" + +config BAT1_ACCESS_RO + bool "Read-only" + +config BAT1_ACCESS_RW + bool "Read-write" + +endchoice + +config BAT1_ICACHE_WRITETHROUGH + bool "I-cache Write-through" + +config BAT1_ICACHE_INHIBITED + bool "I-cache Inhibited" + +config BAT1_ICACHE_MEMORYCOHERENCE + bool "I-cache Memory coherence" + +config BAT1_ICACHE_GUARDED + bool "I-cache Guarded" + +config BAT1_DCACHE_WRITETHROUGH + bool "D-cache Write-through" + +config BAT1_DCACHE_INHIBITED + bool "D-cache Inhibited" + +config BAT1_DCACHE_MEMORYCOHERENCE + bool "D-cache Memory coherence" + +config BAT1_DCACHE_GUARDED + bool "D-cache Guarded" + +config BAT1_USER_MODE_VALID + bool "User mode valid" + +config BAT1_SUPERVISOR_MODE_VALID + bool "Supervisor mode valid" + +endif + +config BAT1_LENGTH + hex + default 0x00000000 if BAT1_LENGTH_128_KBYTES + default 0x00000004 if BAT1_LENGTH_256_KBYTES + default 0x0000000c if BAT1_LENGTH_512_KBYTES + default 0x0000001c if BAT1_LENGTH_1_MBYTES + default 0x0000003c if BAT1_LENGTH_2_MBYTES + default 0x0000007c if BAT1_LENGTH_4_MBYTES + default 0x000000fc if BAT1_LENGTH_8_MBYTES + default 0x000001fc if BAT1_LENGTH_16_MBYTES + default 0x000003fc if BAT1_LENGTH_32_MBYTES + default 0x000007fc if BAT1_LENGTH_64_MBYTES + default 0x00000ffc if BAT1_LENGTH_128_MBYTES + default 0x00001ffc if BAT1_LENGTH_256_MBYTES + +config BAT1_PAGE_PROTECTION + hex + default 0x0 if BAT1_ACCESS_NONE + default 0x1 if BAT1_ACCESS_RO + default 0x2 if BAT1_ACCESS_RW + +config BAT1_WIMG_ICACHE + hex + default 0x0 if !BAT1_ICACHE_WRITETHROUGH && !BAT1_ICACHE_INHIBITED && !BAT1_ICACHE_MEMORYCOHERENCE && !BAT1_ICACHE_GUARDED + default 0x8 if !BAT1_ICACHE_WRITETHROUGH && !BAT1_ICACHE_INHIBITED && !BAT1_ICACHE_MEMORYCOHERENCE && BAT1_ICACHE_GUARDED + default 0x10 if !BAT1_ICACHE_WRITETHROUGH && !BAT1_ICACHE_INHIBITED && BAT1_ICACHE_MEMORYCOHERENCE && !BAT1_ICACHE_GUARDED + default 0x18 if !BAT1_ICACHE_WRITETHROUGH && !BAT1_ICACHE_INHIBITED && BAT1_ICACHE_MEMORYCOHERENCE && BAT1_ICACHE_GUARDED + default 0x20 if !BAT1_ICACHE_WRITETHROUGH && BAT1_ICACHE_INHIBITED && !BAT1_ICACHE_MEMORYCOHERENCE && !BAT1_ICACHE_GUARDED + default 0x28 if !BAT1_ICACHE_WRITETHROUGH && BAT1_ICACHE_INHIBITED && !BAT1_ICACHE_MEMORYCOHERENCE && BAT1_ICACHE_GUARDED + default 0x30 if !BAT1_ICACHE_WRITETHROUGH && BAT1_ICACHE_INHIBITED && BAT1_ICACHE_MEMORYCOHERENCE && !BAT1_ICACHE_GUARDED + default 0x38 if !BAT1_ICACHE_WRITETHROUGH && BAT1_ICACHE_INHIBITED && BAT1_ICACHE_MEMORYCOHERENCE && BAT1_ICACHE_GUARDED + default 0x40 if BAT1_ICACHE_WRITETHROUGH && !BAT1_ICACHE_INHIBITED && !BAT1_ICACHE_MEMORYCOHERENCE && !BAT1_ICACHE_GUARDED + default 0x48 if BAT1_ICACHE_WRITETHROUGH && !BAT1_ICACHE_INHIBITED && !BAT1_ICACHE_MEMORYCOHERENCE && BAT1_ICACHE_GUARDED + default 0x50 if BAT1_ICACHE_WRITETHROUGH && !BAT1_ICACHE_INHIBITED && BAT1_ICACHE_MEMORYCOHERENCE && !BAT1_ICACHE_GUARDED + default 0x58 if BAT1_ICACHE_WRITETHROUGH && !BAT1_ICACHE_INHIBITED && BAT1_ICACHE_MEMORYCOHERENCE && BAT1_ICACHE_GUARDED + default 0x60 if BAT1_ICACHE_WRITETHROUGH && BAT1_ICACHE_INHIBITED && !BAT1_ICACHE_MEMORYCOHERENCE && !BAT1_ICACHE_GUARDED + default 0x68 if BAT1_ICACHE_WRITETHROUGH && BAT1_ICACHE_INHIBITED && !BAT1_ICACHE_MEMORYCOHERENCE && BAT1_ICACHE_GUARDED + default 0x70 if BAT1_ICACHE_WRITETHROUGH && BAT1_ICACHE_INHIBITED && BAT1_ICACHE_MEMORYCOHERENCE && !BAT1_ICACHE_GUARDED + default 0x78 if BAT1_ICACHE_WRITETHROUGH && BAT1_ICACHE_INHIBITED && BAT1_ICACHE_MEMORYCOHERENCE && BAT1_ICACHE_GUARDED + +config BAT1_WIMG_DCACHE + hex + default 0x0 if !BAT1_DCACHE_WRITETHROUGH && !BAT1_DCACHE_INHIBITED && !BAT1_DCACHE_MEMORYCOHERENCE && !BAT1_DCACHE_GUARDED + default 0x8 if !BAT1_DCACHE_WRITETHROUGH && !BAT1_DCACHE_INHIBITED && !BAT1_DCACHE_MEMORYCOHERENCE && BAT1_DCACHE_GUARDED + default 0x10 if !BAT1_DCACHE_WRITETHROUGH && !BAT1_DCACHE_INHIBITED && BAT1_DCACHE_MEMORYCOHERENCE && !BAT1_DCACHE_GUARDED + default 0x18 if !BAT1_DCACHE_WRITETHROUGH && !BAT1_DCACHE_INHIBITED && BAT1_DCACHE_MEMORYCOHERENCE && BAT1_DCACHE_GUARDED + default 0x20 if !BAT1_DCACHE_WRITETHROUGH && BAT1_DCACHE_INHIBITED && !BAT1_DCACHE_MEMORYCOHERENCE && !BAT1_DCACHE_GUARDED + default 0x28 if !BAT1_DCACHE_WRITETHROUGH && BAT1_DCACHE_INHIBITED && !BAT1_DCACHE_MEMORYCOHERENCE && BAT1_DCACHE_GUARDED + default 0x30 if !BAT1_DCACHE_WRITETHROUGH && BAT1_DCACHE_INHIBITED && BAT1_DCACHE_MEMORYCOHERENCE && !BAT1_DCACHE_GUARDED + default 0x38 if !BAT1_DCACHE_WRITETHROUGH && BAT1_DCACHE_INHIBITED && BAT1_DCACHE_MEMORYCOHERENCE && BAT1_DCACHE_GUARDED + default 0x40 if BAT1_DCACHE_WRITETHROUGH && !BAT1_DCACHE_INHIBITED && !BAT1_DCACHE_MEMORYCOHERENCE && !BAT1_DCACHE_GUARDED + default 0x48 if BAT1_DCACHE_WRITETHROUGH && !BAT1_DCACHE_INHIBITED && !BAT1_DCACHE_MEMORYCOHERENCE && BAT1_DCACHE_GUARDED + default 0x50 if BAT1_DCACHE_WRITETHROUGH && !BAT1_DCACHE_INHIBITED && BAT1_DCACHE_MEMORYCOHERENCE && !BAT1_DCACHE_GUARDED + default 0x58 if BAT1_DCACHE_WRITETHROUGH && !BAT1_DCACHE_INHIBITED && BAT1_DCACHE_MEMORYCOHERENCE && BAT1_DCACHE_GUARDED + default 0x60 if BAT1_DCACHE_WRITETHROUGH && BAT1_DCACHE_INHIBITED && !BAT1_DCACHE_MEMORYCOHERENCE && !BAT1_DCACHE_GUARDED + default 0x68 if BAT1_DCACHE_WRITETHROUGH && BAT1_DCACHE_INHIBITED && !BAT1_DCACHE_MEMORYCOHERENCE && BAT1_DCACHE_GUARDED + default 0x70 if BAT1_DCACHE_WRITETHROUGH && BAT1_DCACHE_INHIBITED && BAT1_DCACHE_MEMORYCOHERENCE && !BAT1_DCACHE_GUARDED + default 0x78 if BAT1_DCACHE_WRITETHROUGH && BAT1_DCACHE_INHIBITED && BAT1_DCACHE_MEMORYCOHERENCE && BAT1_DCACHE_GUARDED + +config BAT1_VALID_BITS + hex + default 0x0 if !BAT1_SUPERVISOR_MODE_VALID && !BAT1_USER_MODE_VALID + default 0x1 if !BAT1_SUPERVISOR_MODE_VALID && BAT1_USER_MODE_VALID + default 0x2 if BAT1_SUPERVISOR_MODE_VALID && !BAT1_USER_MODE_VALID + default 0x3 if BAT1_SUPERVISOR_MODE_VALID && BAT1_USER_MODE_VALID + +menuconfig BAT2 + bool "BAT2" + +if BAT2 + +config BAT2_NAME + string "Identifier" + +config BAT2_BASE + hex "Base" + +choice + prompt "Block length" + +config BAT2_LENGTH_128_KBYTES + bool "128 kb" + +config BAT2_LENGTH_256_KBYTES + bool "256 kb" + +config BAT2_LENGTH_512_KBYTES + bool "512 kb" + +config BAT2_LENGTH_1_MBYTES + bool "1 mb" + +config BAT2_LENGTH_2_MBYTES + bool "2 mb" + +config BAT2_LENGTH_4_MBYTES + bool "4 mb" + +config BAT2_LENGTH_8_MBYTES + bool "8 mb" + +config BAT2_LENGTH_16_MBYTES + bool "16 mb" + +config BAT2_LENGTH_32_MBYTES + bool "32 mb" + +config BAT2_LENGTH_64_MBYTES + bool "64 mb" + +config BAT2_LENGTH_128_MBYTES + bool "128 mb" + +config BAT2_LENGTH_256_MBYTES + bool "256 mb" +endchoice + +choice + prompt "Protection mode" + +config BAT2_ACCESS_NONE + bool "No access" + +config BAT2_ACCESS_RO + bool "Read-only" + +config BAT2_ACCESS_RW + bool "Read-write" + +endchoice + +config BAT2_ICACHE_WRITETHROUGH + bool "I-cache Write-through" + +config BAT2_ICACHE_INHIBITED + bool "I-cache Inhibited" + +config BAT2_ICACHE_MEMORYCOHERENCE + bool "I-cache Memory coherence" + +config BAT2_ICACHE_GUARDED + bool "I-cache Guarded" + +config BAT2_DCACHE_WRITETHROUGH + bool "D-cache Write-through" + +config BAT2_DCACHE_INHIBITED + bool "D-cache Inhibited" + +config BAT2_DCACHE_MEMORYCOHERENCE + bool "D-cache Memory coherence" + +config BAT2_DCACHE_GUARDED + bool "D-cache Guarded" + +config BAT2_USER_MODE_VALID + bool "User mode valid" + +config BAT2_SUPERVISOR_MODE_VALID + bool "Supervisor mode valid" + +endif + +config BAT2_LENGTH + hex + default 0x00000000 if BAT2_LENGTH_128_KBYTES + default 0x00000004 if BAT2_LENGTH_256_KBYTES + default 0x0000000c if BAT2_LENGTH_512_KBYTES + default 0x0000001c if BAT2_LENGTH_1_MBYTES + default 0x0000003c if BAT2_LENGTH_2_MBYTES + default 0x0000007c if BAT2_LENGTH_4_MBYTES + default 0x000000fc if BAT2_LENGTH_8_MBYTES + default 0x000001fc if BAT2_LENGTH_16_MBYTES + default 0x000003fc if BAT2_LENGTH_32_MBYTES + default 0x000007fc if BAT2_LENGTH_64_MBYTES + default 0x00000ffc if BAT2_LENGTH_128_MBYTES + default 0x00001ffc if BAT2_LENGTH_256_MBYTES + +config BAT2_PAGE_PROTECTION + hex + default 0x0 if BAT2_ACCESS_NONE + default 0x1 if BAT2_ACCESS_RO + default 0x2 if BAT2_ACCESS_RW + +config BAT2_WIMG_ICACHE + hex + default 0x0 if !BAT2_ICACHE_WRITETHROUGH && !BAT2_ICACHE_INHIBITED && !BAT2_ICACHE_MEMORYCOHERENCE && !BAT2_ICACHE_GUARDED + default 0x8 if !BAT2_ICACHE_WRITETHROUGH && !BAT2_ICACHE_INHIBITED && !BAT2_ICACHE_MEMORYCOHERENCE && BAT2_ICACHE_GUARDED + default 0x10 if !BAT2_ICACHE_WRITETHROUGH && !BAT2_ICACHE_INHIBITED && BAT2_ICACHE_MEMORYCOHERENCE && !BAT2_ICACHE_GUARDED + default 0x18 if !BAT2_ICACHE_WRITETHROUGH && !BAT2_ICACHE_INHIBITED && BAT2_ICACHE_MEMORYCOHERENCE && BAT2_ICACHE_GUARDED + default 0x20 if !BAT2_ICACHE_WRITETHROUGH && BAT2_ICACHE_INHIBITED && !BAT2_ICACHE_MEMORYCOHERENCE && !BAT2_ICACHE_GUARDED + default 0x28 if !BAT2_ICACHE_WRITETHROUGH && BAT2_ICACHE_INHIBITED && !BAT2_ICACHE_MEMORYCOHERENCE && BAT2_ICACHE_GUARDED + default 0x30 if !BAT2_ICACHE_WRITETHROUGH && BAT2_ICACHE_INHIBITED && BAT2_ICACHE_MEMORYCOHERENCE && !BAT2_ICACHE_GUARDED + default 0x38 if !BAT2_ICACHE_WRITETHROUGH && BAT2_ICACHE_INHIBITED && BAT2_ICACHE_MEMORYCOHERENCE && BAT2_ICACHE_GUARDED + default 0x40 if BAT2_ICACHE_WRITETHROUGH && !BAT2_ICACHE_INHIBITED && !BAT2_ICACHE_MEMORYCOHERENCE && !BAT2_ICACHE_GUARDED + default 0x48 if BAT2_ICACHE_WRITETHROUGH && !BAT2_ICACHE_INHIBITED && !BAT2_ICACHE_MEMORYCOHERENCE && BAT2_ICACHE_GUARDED + default 0x50 if BAT2_ICACHE_WRITETHROUGH && !BAT2_ICACHE_INHIBITED && BAT2_ICACHE_MEMORYCOHERENCE && !BAT2_ICACHE_GUARDED + default 0x58 if BAT2_ICACHE_WRITETHROUGH && !BAT2_ICACHE_INHIBITED && BAT2_ICACHE_MEMORYCOHERENCE && BAT2_ICACHE_GUARDED + default 0x60 if BAT2_ICACHE_WRITETHROUGH && BAT2_ICACHE_INHIBITED && !BAT2_ICACHE_MEMORYCOHERENCE && !BAT2_ICACHE_GUARDED + default 0x68 if BAT2_ICACHE_WRITETHROUGH && BAT2_ICACHE_INHIBITED && !BAT2_ICACHE_MEMORYCOHERENCE && BAT2_ICACHE_GUARDED + default 0x70 if BAT2_ICACHE_WRITETHROUGH && BAT2_ICACHE_INHIBITED && BAT2_ICACHE_MEMORYCOHERENCE && !BAT2_ICACHE_GUARDED + default 0x78 if BAT2_ICACHE_WRITETHROUGH && BAT2_ICACHE_INHIBITED && BAT2_ICACHE_MEMORYCOHERENCE && BAT2_ICACHE_GUARDED + +config BAT2_WIMG_DCACHE + hex + default 0x0 if !BAT2_DCACHE_WRITETHROUGH && !BAT2_DCACHE_INHIBITED && !BAT2_DCACHE_MEMORYCOHERENCE && !BAT2_DCACHE_GUARDED + default 0x8 if !BAT2_DCACHE_WRITETHROUGH && !BAT2_DCACHE_INHIBITED && !BAT2_DCACHE_MEMORYCOHERENCE && BAT2_DCACHE_GUARDED + default 0x10 if !BAT2_DCACHE_WRITETHROUGH && !BAT2_DCACHE_INHIBITED && BAT2_DCACHE_MEMORYCOHERENCE && !BAT2_DCACHE_GUARDED + default 0x18 if !BAT2_DCACHE_WRITETHROUGH && !BAT2_DCACHE_INHIBITED && BAT2_DCACHE_MEMORYCOHERENCE && BAT2_DCACHE_GUARDED + default 0x20 if !BAT2_DCACHE_WRITETHROUGH && BAT2_DCACHE_INHIBITED && !BAT2_DCACHE_MEMORYCOHERENCE && !BAT2_DCACHE_GUARDED + default 0x28 if !BAT2_DCACHE_WRITETHROUGH && BAT2_DCACHE_INHIBITED && !BAT2_DCACHE_MEMORYCOHERENCE && BAT2_DCACHE_GUARDED + default 0x30 if !BAT2_DCACHE_WRITETHROUGH && BAT2_DCACHE_INHIBITED && BAT2_DCACHE_MEMORYCOHERENCE && !BAT2_DCACHE_GUARDED + default 0x38 if !BAT2_DCACHE_WRITETHROUGH && BAT2_DCACHE_INHIBITED && BAT2_DCACHE_MEMORYCOHERENCE && BAT2_DCACHE_GUARDED + default 0x40 if BAT2_DCACHE_WRITETHROUGH && !BAT2_DCACHE_INHIBITED && !BAT2_DCACHE_MEMORYCOHERENCE && !BAT2_DCACHE_GUARDED + default 0x48 if BAT2_DCACHE_WRITETHROUGH && !BAT2_DCACHE_INHIBITED && !BAT2_DCACHE_MEMORYCOHERENCE && BAT2_DCACHE_GUARDED + default 0x50 if BAT2_DCACHE_WRITETHROUGH && !BAT2_DCACHE_INHIBITED && BAT2_DCACHE_MEMORYCOHERENCE && !BAT2_DCACHE_GUARDED + default 0x58 if BAT2_DCACHE_WRITETHROUGH && !BAT2_DCACHE_INHIBITED && BAT2_DCACHE_MEMORYCOHERENCE && BAT2_DCACHE_GUARDED + default 0x60 if BAT2_DCACHE_WRITETHROUGH && BAT2_DCACHE_INHIBITED && !BAT2_DCACHE_MEMORYCOHERENCE && !BAT2_DCACHE_GUARDED + default 0x68 if BAT2_DCACHE_WRITETHROUGH && BAT2_DCACHE_INHIBITED && !BAT2_DCACHE_MEMORYCOHERENCE && BAT2_DCACHE_GUARDED + default 0x70 if BAT2_DCACHE_WRITETHROUGH && BAT2_DCACHE_INHIBITED && BAT2_DCACHE_MEMORYCOHERENCE && !BAT2_DCACHE_GUARDED + default 0x78 if BAT2_DCACHE_WRITETHROUGH && BAT2_DCACHE_INHIBITED && BAT2_DCACHE_MEMORYCOHERENCE && BAT2_DCACHE_GUARDED + +config BAT2_VALID_BITS + hex + default 0x0 if !BAT2_SUPERVISOR_MODE_VALID && !BAT2_USER_MODE_VALID + default 0x1 if !BAT2_SUPERVISOR_MODE_VALID && BAT2_USER_MODE_VALID + default 0x2 if BAT2_SUPERVISOR_MODE_VALID && !BAT2_USER_MODE_VALID + default 0x3 if BAT2_SUPERVISOR_MODE_VALID && BAT2_USER_MODE_VALID + +menuconfig BAT3 + bool "BAT3" + +if BAT3 + +config BAT3_NAME + string "Identifier" + +config BAT3_BASE + hex "Base" + +choice + prompt "Block length" + +config BAT3_LENGTH_128_KBYTES + bool "128 kb" + +config BAT3_LENGTH_256_KBYTES + bool "256 kb" + +config BAT3_LENGTH_512_KBYTES + bool "512 kb" + +config BAT3_LENGTH_1_MBYTES + bool "1 mb" + +config BAT3_LENGTH_2_MBYTES + bool "2 mb" + +config BAT3_LENGTH_4_MBYTES + bool "4 mb" + +config BAT3_LENGTH_8_MBYTES + bool "8 mb" + +config BAT3_LENGTH_16_MBYTES + bool "16 mb" + +config BAT3_LENGTH_32_MBYTES + bool "32 mb" + +config BAT3_LENGTH_64_MBYTES + bool "64 mb" + +config BAT3_LENGTH_128_MBYTES + bool "128 mb" + +config BAT3_LENGTH_256_MBYTES + bool "256 mb" +endchoice + +choice + prompt "Protection mode" + +config BAT3_ACCESS_NONE + bool "No access" + +config BAT3_ACCESS_RO + bool "Read-only" + +config BAT3_ACCESS_RW + bool "Read-write" + +endchoice + +config BAT3_ICACHE_WRITETHROUGH + bool "I-cache Write-through" + +config BAT3_ICACHE_INHIBITED + bool "I-cache Inhibited" + +config BAT3_ICACHE_MEMORYCOHERENCE + bool "I-cache Memory coherence" + +config BAT3_ICACHE_GUARDED + bool "I-cache Guarded" + +config BAT3_DCACHE_WRITETHROUGH + bool "D-cache Write-through" + +config BAT3_DCACHE_INHIBITED + bool "D-cache Inhibited" + +config BAT3_DCACHE_MEMORYCOHERENCE + bool "D-cache Memory coherence" + +config BAT3_DCACHE_GUARDED + bool "D-cache Guarded" + +config BAT3_USER_MODE_VALID + bool "User mode valid" + +config BAT3_SUPERVISOR_MODE_VALID + bool "Supervisor mode valid" + +endif + +config BAT3_LENGTH + hex + default 0x00000000 if BAT3_LENGTH_128_KBYTES + default 0x00000004 if BAT3_LENGTH_256_KBYTES + default 0x0000000c if BAT3_LENGTH_512_KBYTES + default 0x0000001c if BAT3_LENGTH_1_MBYTES + default 0x0000003c if BAT3_LENGTH_2_MBYTES + default 0x0000007c if BAT3_LENGTH_4_MBYTES + default 0x000000fc if BAT3_LENGTH_8_MBYTES + default 0x000001fc if BAT3_LENGTH_16_MBYTES + default 0x000003fc if BAT3_LENGTH_32_MBYTES + default 0x000007fc if BAT3_LENGTH_64_MBYTES + default 0x00000ffc if BAT3_LENGTH_128_MBYTES + default 0x00001ffc if BAT3_LENGTH_256_MBYTES + +config BAT3_PAGE_PROTECTION + hex + default 0x0 if BAT3_ACCESS_NONE + default 0x1 if BAT3_ACCESS_RO + default 0x2 if BAT3_ACCESS_RW + +config BAT3_WIMG_ICACHE + hex + default 0x0 if !BAT3_ICACHE_WRITETHROUGH && !BAT3_ICACHE_INHIBITED && !BAT3_ICACHE_MEMORYCOHERENCE && !BAT3_ICACHE_GUARDED + default 0x8 if !BAT3_ICACHE_WRITETHROUGH && !BAT3_ICACHE_INHIBITED && !BAT3_ICACHE_MEMORYCOHERENCE && BAT3_ICACHE_GUARDED + default 0x10 if !BAT3_ICACHE_WRITETHROUGH && !BAT3_ICACHE_INHIBITED && BAT3_ICACHE_MEMORYCOHERENCE && !BAT3_ICACHE_GUARDED + default 0x18 if !BAT3_ICACHE_WRITETHROUGH && !BAT3_ICACHE_INHIBITED && BAT3_ICACHE_MEMORYCOHERENCE && BAT3_ICACHE_GUARDED + default 0x20 if !BAT3_ICACHE_WRITETHROUGH && BAT3_ICACHE_INHIBITED && !BAT3_ICACHE_MEMORYCOHERENCE && !BAT3_ICACHE_GUARDED + default 0x28 if !BAT3_ICACHE_WRITETHROUGH && BAT3_ICACHE_INHIBITED && !BAT3_ICACHE_MEMORYCOHERENCE && BAT3_ICACHE_GUARDED + default 0x30 if !BAT3_ICACHE_WRITETHROUGH && BAT3_ICACHE_INHIBITED && BAT3_ICACHE_MEMORYCOHERENCE && !BAT3_ICACHE_GUARDED + default 0x38 if !BAT3_ICACHE_WRITETHROUGH && BAT3_ICACHE_INHIBITED && BAT3_ICACHE_MEMORYCOHERENCE && BAT3_ICACHE_GUARDED + default 0x40 if BAT3_ICACHE_WRITETHROUGH && !BAT3_ICACHE_INHIBITED && !BAT3_ICACHE_MEMORYCOHERENCE && !BAT3_ICACHE_GUARDED + default 0x48 if BAT3_ICACHE_WRITETHROUGH && !BAT3_ICACHE_INHIBITED && !BAT3_ICACHE_MEMORYCOHERENCE && BAT3_ICACHE_GUARDED + default 0x50 if BAT3_ICACHE_WRITETHROUGH && !BAT3_ICACHE_INHIBITED && BAT3_ICACHE_MEMORYCOHERENCE && !BAT3_ICACHE_GUARDED + default 0x58 if BAT3_ICACHE_WRITETHROUGH && !BAT3_ICACHE_INHIBITED && BAT3_ICACHE_MEMORYCOHERENCE && BAT3_ICACHE_GUARDED + default 0x60 if BAT3_ICACHE_WRITETHROUGH && BAT3_ICACHE_INHIBITED && !BAT3_ICACHE_MEMORYCOHERENCE && !BAT3_ICACHE_GUARDED + default 0x68 if BAT3_ICACHE_WRITETHROUGH && BAT3_ICACHE_INHIBITED && !BAT3_ICACHE_MEMORYCOHERENCE && BAT3_ICACHE_GUARDED + default 0x70 if BAT3_ICACHE_WRITETHROUGH && BAT3_ICACHE_INHIBITED && BAT3_ICACHE_MEMORYCOHERENCE && !BAT3_ICACHE_GUARDED + default 0x78 if BAT3_ICACHE_WRITETHROUGH && BAT3_ICACHE_INHIBITED && BAT3_ICACHE_MEMORYCOHERENCE && BAT3_ICACHE_GUARDED + +config BAT3_WIMG_DCACHE + hex + default 0x0 if !BAT3_DCACHE_WRITETHROUGH && !BAT3_DCACHE_INHIBITED && !BAT3_DCACHE_MEMORYCOHERENCE && !BAT3_DCACHE_GUARDED + default 0x8 if !BAT3_DCACHE_WRITETHROUGH && !BAT3_DCACHE_INHIBITED && !BAT3_DCACHE_MEMORYCOHERENCE && BAT3_DCACHE_GUARDED + default 0x10 if !BAT3_DCACHE_WRITETHROUGH && !BAT3_DCACHE_INHIBITED && BAT3_DCACHE_MEMORYCOHERENCE && !BAT3_DCACHE_GUARDED + default 0x18 if !BAT3_DCACHE_WRITETHROUGH && !BAT3_DCACHE_INHIBITED && BAT3_DCACHE_MEMORYCOHERENCE && BAT3_DCACHE_GUARDED + default 0x20 if !BAT3_DCACHE_WRITETHROUGH && BAT3_DCACHE_INHIBITED && !BAT3_DCACHE_MEMORYCOHERENCE && !BAT3_DCACHE_GUARDED + default 0x28 if !BAT3_DCACHE_WRITETHROUGH && BAT3_DCACHE_INHIBITED && !BAT3_DCACHE_MEMORYCOHERENCE && BAT3_DCACHE_GUARDED + default 0x30 if !BAT3_DCACHE_WRITETHROUGH && BAT3_DCACHE_INHIBITED && BAT3_DCACHE_MEMORYCOHERENCE && !BAT3_DCACHE_GUARDED + default 0x38 if !BAT3_DCACHE_WRITETHROUGH && BAT3_DCACHE_INHIBITED && BAT3_DCACHE_MEMORYCOHERENCE && BAT3_DCACHE_GUARDED + default 0x40 if BAT3_DCACHE_WRITETHROUGH && !BAT3_DCACHE_INHIBITED && !BAT3_DCACHE_MEMORYCOHERENCE && !BAT3_DCACHE_GUARDED + default 0x48 if BAT3_DCACHE_WRITETHROUGH && !BAT3_DCACHE_INHIBITED && !BAT3_DCACHE_MEMORYCOHERENCE && BAT3_DCACHE_GUARDED + default 0x50 if BAT3_DCACHE_WRITETHROUGH && !BAT3_DCACHE_INHIBITED && BAT3_DCACHE_MEMORYCOHERENCE && !BAT3_DCACHE_GUARDED + default 0x58 if BAT3_DCACHE_WRITETHROUGH && !BAT3_DCACHE_INHIBITED && BAT3_DCACHE_MEMORYCOHERENCE && BAT3_DCACHE_GUARDED + default 0x60 if BAT3_DCACHE_WRITETHROUGH && BAT3_DCACHE_INHIBITED && !BAT3_DCACHE_MEMORYCOHERENCE && !BAT3_DCACHE_GUARDED + default 0x68 if BAT3_DCACHE_WRITETHROUGH && BAT3_DCACHE_INHIBITED && !BAT3_DCACHE_MEMORYCOHERENCE && BAT3_DCACHE_GUARDED + default 0x70 if BAT3_DCACHE_WRITETHROUGH && BAT3_DCACHE_INHIBITED && BAT3_DCACHE_MEMORYCOHERENCE && !BAT3_DCACHE_GUARDED + default 0x78 if BAT3_DCACHE_WRITETHROUGH && BAT3_DCACHE_INHIBITED && BAT3_DCACHE_MEMORYCOHERENCE && BAT3_DCACHE_GUARDED + +config BAT3_VALID_BITS + hex + default 0x0 if !BAT3_SUPERVISOR_MODE_VALID && !BAT3_USER_MODE_VALID + default 0x1 if !BAT3_SUPERVISOR_MODE_VALID && BAT3_USER_MODE_VALID + default 0x2 if BAT3_SUPERVISOR_MODE_VALID && !BAT3_USER_MODE_VALID + default 0x3 if BAT3_SUPERVISOR_MODE_VALID && BAT3_USER_MODE_VALID + +if HIGH_BATS + +menuconfig BAT4 + bool "BAT4" + +if BAT4 + +config BAT4_NAME + string "Identifier" + +config BAT4_BASE + hex "Base" + +choice + prompt "Block length" + +config BAT4_LENGTH_128_KBYTES + bool "128 kb" + +config BAT4_LENGTH_256_KBYTES + bool "256 kb" + +config BAT4_LENGTH_512_KBYTES + bool "512 kb" + +config BAT4_LENGTH_1_MBYTES + bool "1 mb" + +config BAT4_LENGTH_2_MBYTES + bool "2 mb" + +config BAT4_LENGTH_4_MBYTES + bool "4 mb" + +config BAT4_LENGTH_8_MBYTES + bool "8 mb" + +config BAT4_LENGTH_16_MBYTES + bool "16 mb" + +config BAT4_LENGTH_32_MBYTES + bool "32 mb" + +config BAT4_LENGTH_64_MBYTES + bool "64 mb" + +config BAT4_LENGTH_128_MBYTES + bool "128 mb" + +config BAT4_LENGTH_256_MBYTES + bool "256 mb" +endchoice + +choice + prompt "Protection mode" + +config BAT4_ACCESS_NONE + bool "No access" + +config BAT4_ACCESS_RO + bool "Read-only" + +config BAT4_ACCESS_RW + bool "Read-write" + +endchoice + +config BAT4_ICACHE_WRITETHROUGH + bool "I-cache Write-through" + +config BAT4_ICACHE_INHIBITED + bool "I-cache Inhibited" + +config BAT4_ICACHE_MEMORYCOHERENCE + bool "I-cache Memory coherence" + +config BAT4_ICACHE_GUARDED + bool "I-cache Guarded" + +config BAT4_DCACHE_WRITETHROUGH + bool "D-cache Write-through" + +config BAT4_DCACHE_INHIBITED + bool "D-cache Inhibited" + +config BAT4_DCACHE_MEMORYCOHERENCE + bool "D-cache Memory coherence" + +config BAT4_DCACHE_GUARDED + bool "D-cache Guarded" + +config BAT4_USER_MODE_VALID + bool "User mode valid" + +config BAT4_SUPERVISOR_MODE_VALID + bool "Supervisor mode valid" + +endif + +config BAT4_LENGTH + hex + default 0x00000000 if BAT4_LENGTH_128_KBYTES + default 0x00000004 if BAT4_LENGTH_256_KBYTES + default 0x0000000c if BAT4_LENGTH_512_KBYTES + default 0x0000001c if BAT4_LENGTH_1_MBYTES + default 0x0000003c if BAT4_LENGTH_2_MBYTES + default 0x0000007c if BAT4_LENGTH_4_MBYTES + default 0x000000fc if BAT4_LENGTH_8_MBYTES + default 0x000001fc if BAT4_LENGTH_16_MBYTES + default 0x000003fc if BAT4_LENGTH_32_MBYTES + default 0x000007fc if BAT4_LENGTH_64_MBYTES + default 0x00000ffc if BAT4_LENGTH_128_MBYTES + default 0x00001ffc if BAT4_LENGTH_256_MBYTES + +config BAT4_PAGE_PROTECTION + hex + default 0x0 if BAT4_ACCESS_NONE + default 0x1 if BAT4_ACCESS_RO + default 0x2 if BAT4_ACCESS_RW + +config BAT4_WIMG_ICACHE + hex + default 0x0 if !BAT4_ICACHE_WRITETHROUGH && !BAT4_ICACHE_INHIBITED && !BAT4_ICACHE_MEMORYCOHERENCE && !BAT4_ICACHE_GUARDED + default 0x8 if !BAT4_ICACHE_WRITETHROUGH && !BAT4_ICACHE_INHIBITED && !BAT4_ICACHE_MEMORYCOHERENCE && BAT4_ICACHE_GUARDED + default 0x10 if !BAT4_ICACHE_WRITETHROUGH && !BAT4_ICACHE_INHIBITED && BAT4_ICACHE_MEMORYCOHERENCE && !BAT4_ICACHE_GUARDED + default 0x18 if !BAT4_ICACHE_WRITETHROUGH && !BAT4_ICACHE_INHIBITED && BAT4_ICACHE_MEMORYCOHERENCE && BAT4_ICACHE_GUARDED + default 0x20 if !BAT4_ICACHE_WRITETHROUGH && BAT4_ICACHE_INHIBITED && !BAT4_ICACHE_MEMORYCOHERENCE && !BAT4_ICACHE_GUARDED + default 0x28 if !BAT4_ICACHE_WRITETHROUGH && BAT4_ICACHE_INHIBITED && !BAT4_ICACHE_MEMORYCOHERENCE && BAT4_ICACHE_GUARDED + default 0x30 if !BAT4_ICACHE_WRITETHROUGH && BAT4_ICACHE_INHIBITED && BAT4_ICACHE_MEMORYCOHERENCE && !BAT4_ICACHE_GUARDED + default 0x38 if !BAT4_ICACHE_WRITETHROUGH && BAT4_ICACHE_INHIBITED && BAT4_ICACHE_MEMORYCOHERENCE && BAT4_ICACHE_GUARDED + default 0x40 if BAT4_ICACHE_WRITETHROUGH && !BAT4_ICACHE_INHIBITED && !BAT4_ICACHE_MEMORYCOHERENCE && !BAT4_ICACHE_GUARDED + default 0x48 if BAT4_ICACHE_WRITETHROUGH && !BAT4_ICACHE_INHIBITED && !BAT4_ICACHE_MEMORYCOHERENCE && BAT4_ICACHE_GUARDED + default 0x50 if BAT4_ICACHE_WRITETHROUGH && !BAT4_ICACHE_INHIBITED && BAT4_ICACHE_MEMORYCOHERENCE && !BAT4_ICACHE_GUARDED + default 0x58 if BAT4_ICACHE_WRITETHROUGH && !BAT4_ICACHE_INHIBITED && BAT4_ICACHE_MEMORYCOHERENCE && BAT4_ICACHE_GUARDED + default 0x60 if BAT4_ICACHE_WRITETHROUGH && BAT4_ICACHE_INHIBITED && !BAT4_ICACHE_MEMORYCOHERENCE && !BAT4_ICACHE_GUARDED + default 0x68 if BAT4_ICACHE_WRITETHROUGH && BAT4_ICACHE_INHIBITED && !BAT4_ICACHE_MEMORYCOHERENCE && BAT4_ICACHE_GUARDED + default 0x70 if BAT4_ICACHE_WRITETHROUGH && BAT4_ICACHE_INHIBITED && BAT4_ICACHE_MEMORYCOHERENCE && !BAT4_ICACHE_GUARDED + default 0x78 if BAT4_ICACHE_WRITETHROUGH && BAT4_ICACHE_INHIBITED && BAT4_ICACHE_MEMORYCOHERENCE && BAT4_ICACHE_GUARDED + +config BAT4_WIMG_DCACHE + hex + default 0x0 if !BAT4_DCACHE_WRITETHROUGH && !BAT4_DCACHE_INHIBITED && !BAT4_DCACHE_MEMORYCOHERENCE && !BAT4_DCACHE_GUARDED + default 0x8 if !BAT4_DCACHE_WRITETHROUGH && !BAT4_DCACHE_INHIBITED && !BAT4_DCACHE_MEMORYCOHERENCE && BAT4_DCACHE_GUARDED + default 0x10 if !BAT4_DCACHE_WRITETHROUGH && !BAT4_DCACHE_INHIBITED && BAT4_DCACHE_MEMORYCOHERENCE && !BAT4_DCACHE_GUARDED + default 0x18 if !BAT4_DCACHE_WRITETHROUGH && !BAT4_DCACHE_INHIBITED && BAT4_DCACHE_MEMORYCOHERENCE && BAT4_DCACHE_GUARDED + default 0x20 if !BAT4_DCACHE_WRITETHROUGH && BAT4_DCACHE_INHIBITED && !BAT4_DCACHE_MEMORYCOHERENCE && !BAT4_DCACHE_GUARDED + default 0x28 if !BAT4_DCACHE_WRITETHROUGH && BAT4_DCACHE_INHIBITED && !BAT4_DCACHE_MEMORYCOHERENCE && BAT4_DCACHE_GUARDED + default 0x30 if !BAT4_DCACHE_WRITETHROUGH && BAT4_DCACHE_INHIBITED && BAT4_DCACHE_MEMORYCOHERENCE && !BAT4_DCACHE_GUARDED + default 0x38 if !BAT4_DCACHE_WRITETHROUGH && BAT4_DCACHE_INHIBITED && BAT4_DCACHE_MEMORYCOHERENCE && BAT4_DCACHE_GUARDED + default 0x40 if BAT4_DCACHE_WRITETHROUGH && !BAT4_DCACHE_INHIBITED && !BAT4_DCACHE_MEMORYCOHERENCE && !BAT4_DCACHE_GUARDED + default 0x48 if BAT4_DCACHE_WRITETHROUGH && !BAT4_DCACHE_INHIBITED && !BAT4_DCACHE_MEMORYCOHERENCE && BAT4_DCACHE_GUARDED + default 0x50 if BAT4_DCACHE_WRITETHROUGH && !BAT4_DCACHE_INHIBITED && BAT4_DCACHE_MEMORYCOHERENCE && !BAT4_DCACHE_GUARDED + default 0x58 if BAT4_DCACHE_WRITETHROUGH && !BAT4_DCACHE_INHIBITED && BAT4_DCACHE_MEMORYCOHERENCE && BAT4_DCACHE_GUARDED + default 0x60 if BAT4_DCACHE_WRITETHROUGH && BAT4_DCACHE_INHIBITED && !BAT4_DCACHE_MEMORYCOHERENCE && !BAT4_DCACHE_GUARDED + default 0x68 if BAT4_DCACHE_WRITETHROUGH && BAT4_DCACHE_INHIBITED && !BAT4_DCACHE_MEMORYCOHERENCE && BAT4_DCACHE_GUARDED + default 0x70 if BAT4_DCACHE_WRITETHROUGH && BAT4_DCACHE_INHIBITED && BAT4_DCACHE_MEMORYCOHERENCE && !BAT4_DCACHE_GUARDED + default 0x78 if BAT4_DCACHE_WRITETHROUGH && BAT4_DCACHE_INHIBITED && BAT4_DCACHE_MEMORYCOHERENCE && BAT4_DCACHE_GUARDED + +config BAT4_VALID_BITS + hex + default 0x0 if !BAT4_SUPERVISOR_MODE_VALID && !BAT4_USER_MODE_VALID + default 0x1 if !BAT4_SUPERVISOR_MODE_VALID && BAT4_USER_MODE_VALID + default 0x2 if BAT4_SUPERVISOR_MODE_VALID && !BAT4_USER_MODE_VALID + default 0x3 if BAT4_SUPERVISOR_MODE_VALID && BAT4_USER_MODE_VALID + +menuconfig BAT5 + bool "BAT5" + +if BAT5 + +config BAT5_NAME + string "Identifier" + +config BAT5_BASE + hex "Base" + +choice + prompt "Block length" + +config BAT5_LENGTH_128_KBYTES + bool "128 kb" + +config BAT5_LENGTH_256_KBYTES + bool "256 kb" + +config BAT5_LENGTH_512_KBYTES + bool "512 kb" + +config BAT5_LENGTH_1_MBYTES + bool "1 mb" + +config BAT5_LENGTH_2_MBYTES + bool "2 mb" + +config BAT5_LENGTH_4_MBYTES + bool "4 mb" + +config BAT5_LENGTH_8_MBYTES + bool "8 mb" + +config BAT5_LENGTH_16_MBYTES + bool "16 mb" + +config BAT5_LENGTH_32_MBYTES + bool "32 mb" + +config BAT5_LENGTH_64_MBYTES + bool "64 mb" + +config BAT5_LENGTH_128_MBYTES + bool "128 mb" + +config BAT5_LENGTH_256_MBYTES + bool "256 mb" +endchoice + +choice + prompt "Protection mode" + +config BAT5_ACCESS_NONE + bool "No access" + +config BAT5_ACCESS_RO + bool "Read-only" + +config BAT5_ACCESS_RW + bool "Read-write" + +endchoice + +config BAT5_ICACHE_WRITETHROUGH + bool "I-cache Write-through" + +config BAT5_ICACHE_INHIBITED + bool "I-cache Inhibited" + +config BAT5_ICACHE_MEMORYCOHERENCE + bool "I-cache Memory coherence" + +config BAT5_ICACHE_GUARDED + bool "I-cache Guarded" + +config BAT5_DCACHE_WRITETHROUGH + bool "D-cache Write-through" + +config BAT5_DCACHE_INHIBITED + bool "D-cache Inhibited" + +config BAT5_DCACHE_MEMORYCOHERENCE + bool "D-cache Memory coherence" + +config BAT5_DCACHE_GUARDED + bool "D-cache Guarded" + +config BAT5_USER_MODE_VALID + bool "User mode valid" + +config BAT5_SUPERVISOR_MODE_VALID + bool "Supervisor mode valid" + +endif + +config BAT5_LENGTH + hex + default 0x00000000 if BAT5_LENGTH_128_KBYTES + default 0x00000004 if BAT5_LENGTH_256_KBYTES + default 0x0000000c if BAT5_LENGTH_512_KBYTES + default 0x0000001c if BAT5_LENGTH_1_MBYTES + default 0x0000003c if BAT5_LENGTH_2_MBYTES + default 0x0000007c if BAT5_LENGTH_4_MBYTES + default 0x000000fc if BAT5_LENGTH_8_MBYTES + default 0x000001fc if BAT5_LENGTH_16_MBYTES + default 0x000003fc if BAT5_LENGTH_32_MBYTES + default 0x000007fc if BAT5_LENGTH_64_MBYTES + default 0x00000ffc if BAT5_LENGTH_128_MBYTES + default 0x00001ffc if BAT5_LENGTH_256_MBYTES + +config BAT5_PAGE_PROTECTION + hex + default 0x0 if BAT5_ACCESS_NONE + default 0x1 if BAT5_ACCESS_RO + default 0x2 if BAT5_ACCESS_RW + +config BAT5_WIMG_ICACHE + hex + default 0x0 if !BAT5_ICACHE_WRITETHROUGH && !BAT5_ICACHE_INHIBITED && !BAT5_ICACHE_MEMORYCOHERENCE && !BAT5_ICACHE_GUARDED + default 0x8 if !BAT5_ICACHE_WRITETHROUGH && !BAT5_ICACHE_INHIBITED && !BAT5_ICACHE_MEMORYCOHERENCE && BAT5_ICACHE_GUARDED + default 0x10 if !BAT5_ICACHE_WRITETHROUGH && !BAT5_ICACHE_INHIBITED && BAT5_ICACHE_MEMORYCOHERENCE && !BAT5_ICACHE_GUARDED + default 0x18 if !BAT5_ICACHE_WRITETHROUGH && !BAT5_ICACHE_INHIBITED && BAT5_ICACHE_MEMORYCOHERENCE && BAT5_ICACHE_GUARDED + default 0x20 if !BAT5_ICACHE_WRITETHROUGH && BAT5_ICACHE_INHIBITED && !BAT5_ICACHE_MEMORYCOHERENCE && !BAT5_ICACHE_GUARDED + default 0x28 if !BAT5_ICACHE_WRITETHROUGH && BAT5_ICACHE_INHIBITED && !BAT5_ICACHE_MEMORYCOHERENCE && BAT5_ICACHE_GUARDED + default 0x30 if !BAT5_ICACHE_WRITETHROUGH && BAT5_ICACHE_INHIBITED && BAT5_ICACHE_MEMORYCOHERENCE && !BAT5_ICACHE_GUARDED + default 0x38 if !BAT5_ICACHE_WRITETHROUGH && BAT5_ICACHE_INHIBITED && BAT5_ICACHE_MEMORYCOHERENCE && BAT5_ICACHE_GUARDED + default 0x40 if BAT5_ICACHE_WRITETHROUGH && !BAT5_ICACHE_INHIBITED && !BAT5_ICACHE_MEMORYCOHERENCE && !BAT5_ICACHE_GUARDED + default 0x48 if BAT5_ICACHE_WRITETHROUGH && !BAT5_ICACHE_INHIBITED && !BAT5_ICACHE_MEMORYCOHERENCE && BAT5_ICACHE_GUARDED + default 0x50 if BAT5_ICACHE_WRITETHROUGH && !BAT5_ICACHE_INHIBITED && BAT5_ICACHE_MEMORYCOHERENCE && !BAT5_ICACHE_GUARDED + default 0x58 if BAT5_ICACHE_WRITETHROUGH && !BAT5_ICACHE_INHIBITED && BAT5_ICACHE_MEMORYCOHERENCE && BAT5_ICACHE_GUARDED + default 0x60 if BAT5_ICACHE_WRITETHROUGH && BAT5_ICACHE_INHIBITED && !BAT5_ICACHE_MEMORYCOHERENCE && !BAT5_ICACHE_GUARDED + default 0x68 if BAT5_ICACHE_WRITETHROUGH && BAT5_ICACHE_INHIBITED && !BAT5_ICACHE_MEMORYCOHERENCE && BAT5_ICACHE_GUARDED + default 0x70 if BAT5_ICACHE_WRITETHROUGH && BAT5_ICACHE_INHIBITED && BAT5_ICACHE_MEMORYCOHERENCE && !BAT5_ICACHE_GUARDED + default 0x78 if BAT5_ICACHE_WRITETHROUGH && BAT5_ICACHE_INHIBITED && BAT5_ICACHE_MEMORYCOHERENCE && BAT5_ICACHE_GUARDED + +config BAT5_WIMG_DCACHE + hex + default 0x0 if !BAT5_DCACHE_WRITETHROUGH && !BAT5_DCACHE_INHIBITED && !BAT5_DCACHE_MEMORYCOHERENCE && !BAT5_DCACHE_GUARDED + default 0x8 if !BAT5_DCACHE_WRITETHROUGH && !BAT5_DCACHE_INHIBITED && !BAT5_DCACHE_MEMORYCOHERENCE && BAT5_DCACHE_GUARDED + default 0x10 if !BAT5_DCACHE_WRITETHROUGH && !BAT5_DCACHE_INHIBITED && BAT5_DCACHE_MEMORYCOHERENCE && !BAT5_DCACHE_GUARDED + default 0x18 if !BAT5_DCACHE_WRITETHROUGH && !BAT5_DCACHE_INHIBITED && BAT5_DCACHE_MEMORYCOHERENCE && BAT5_DCACHE_GUARDED + default 0x20 if !BAT5_DCACHE_WRITETHROUGH && BAT5_DCACHE_INHIBITED && !BAT5_DCACHE_MEMORYCOHERENCE && !BAT5_DCACHE_GUARDED + default 0x28 if !BAT5_DCACHE_WRITETHROUGH && BAT5_DCACHE_INHIBITED && !BAT5_DCACHE_MEMORYCOHERENCE && BAT5_DCACHE_GUARDED + default 0x30 if !BAT5_DCACHE_WRITETHROUGH && BAT5_DCACHE_INHIBITED && BAT5_DCACHE_MEMORYCOHERENCE && !BAT5_DCACHE_GUARDED + default 0x38 if !BAT5_DCACHE_WRITETHROUGH && BAT5_DCACHE_INHIBITED && BAT5_DCACHE_MEMORYCOHERENCE && BAT5_DCACHE_GUARDED + default 0x40 if BAT5_DCACHE_WRITETHROUGH && !BAT5_DCACHE_INHIBITED && !BAT5_DCACHE_MEMORYCOHERENCE && !BAT5_DCACHE_GUARDED + default 0x48 if BAT5_DCACHE_WRITETHROUGH && !BAT5_DCACHE_INHIBITED && !BAT5_DCACHE_MEMORYCOHERENCE && BAT5_DCACHE_GUARDED + default 0x50 if BAT5_DCACHE_WRITETHROUGH && !BAT5_DCACHE_INHIBITED && BAT5_DCACHE_MEMORYCOHERENCE && !BAT5_DCACHE_GUARDED + default 0x58 if BAT5_DCACHE_WRITETHROUGH && !BAT5_DCACHE_INHIBITED && BAT5_DCACHE_MEMORYCOHERENCE && BAT5_DCACHE_GUARDED + default 0x60 if BAT5_DCACHE_WRITETHROUGH && BAT5_DCACHE_INHIBITED && !BAT5_DCACHE_MEMORYCOHERENCE && !BAT5_DCACHE_GUARDED + default 0x68 if BAT5_DCACHE_WRITETHROUGH && BAT5_DCACHE_INHIBITED && !BAT5_DCACHE_MEMORYCOHERENCE && BAT5_DCACHE_GUARDED + default 0x70 if BAT5_DCACHE_WRITETHROUGH && BAT5_DCACHE_INHIBITED && BAT5_DCACHE_MEMORYCOHERENCE && !BAT5_DCACHE_GUARDED + default 0x78 if BAT5_DCACHE_WRITETHROUGH && BAT5_DCACHE_INHIBITED && BAT5_DCACHE_MEMORYCOHERENCE && BAT5_DCACHE_GUARDED + +config BAT5_VALID_BITS + hex + default 0x0 if !BAT5_SUPERVISOR_MODE_VALID && !BAT5_USER_MODE_VALID + default 0x1 if !BAT5_SUPERVISOR_MODE_VALID && BAT5_USER_MODE_VALID + default 0x2 if BAT5_SUPERVISOR_MODE_VALID && !BAT5_USER_MODE_VALID + default 0x3 if BAT5_SUPERVISOR_MODE_VALID && BAT5_USER_MODE_VALID + +menuconfig BAT6 + bool "BAT6" + +if BAT6 + +config BAT6_NAME + string "Identifier" + +config BAT6_BASE + hex "Base" + +choice + prompt "Block length" + +config BAT6_LENGTH_128_KBYTES + bool "128 kb" + +config BAT6_LENGTH_256_KBYTES + bool "256 kb" + +config BAT6_LENGTH_512_KBYTES + bool "512 kb" + +config BAT6_LENGTH_1_MBYTES + bool "1 mb" + +config BAT6_LENGTH_2_MBYTES + bool "2 mb" + +config BAT6_LENGTH_4_MBYTES + bool "4 mb" + +config BAT6_LENGTH_8_MBYTES + bool "8 mb" + +config BAT6_LENGTH_16_MBYTES + bool "16 mb" + +config BAT6_LENGTH_32_MBYTES + bool "32 mb" + +config BAT6_LENGTH_64_MBYTES + bool "64 mb" + +config BAT6_LENGTH_128_MBYTES + bool "128 mb" + +config BAT6_LENGTH_256_MBYTES + bool "256 mb" +endchoice + +choice + prompt "Protection mode" + +config BAT6_ACCESS_NONE + bool "No access" + +config BAT6_ACCESS_RO + bool "Read-only" + +config BAT6_ACCESS_RW + bool "Read-write" + +endchoice + +config BAT6_ICACHE_WRITETHROUGH + bool "I-cache Write-through" + +config BAT6_ICACHE_INHIBITED + bool "I-cache Inhibited" + +config BAT6_ICACHE_MEMORYCOHERENCE + bool "I-cache Memory coherence" + +config BAT6_ICACHE_GUARDED + bool "I-cache Guarded" + +config BAT6_DCACHE_WRITETHROUGH + bool "D-cache Write-through" + +config BAT6_DCACHE_INHIBITED + bool "D-cache Inhibited" + +config BAT6_DCACHE_MEMORYCOHERENCE + bool "D-cache Memory coherence" + +config BAT6_DCACHE_GUARDED + bool "D-cache Guarded" + +config BAT6_USER_MODE_VALID + bool "User mode valid" + +config BAT6_SUPERVISOR_MODE_VALID + bool "Supervisor mode valid" + +endif + +config BAT6_LENGTH + hex + default 0x00000000 if BAT6_LENGTH_128_KBYTES + default 0x00000004 if BAT6_LENGTH_256_KBYTES + default 0x0000000c if BAT6_LENGTH_512_KBYTES + default 0x0000001c if BAT6_LENGTH_1_MBYTES + default 0x0000003c if BAT6_LENGTH_2_MBYTES + default 0x0000007c if BAT6_LENGTH_4_MBYTES + default 0x000000fc if BAT6_LENGTH_8_MBYTES + default 0x000001fc if BAT6_LENGTH_16_MBYTES + default 0x000003fc if BAT6_LENGTH_32_MBYTES + default 0x000007fc if BAT6_LENGTH_64_MBYTES + default 0x00000ffc if BAT6_LENGTH_128_MBYTES + default 0x00001ffc if BAT6_LENGTH_256_MBYTES + +config BAT6_PAGE_PROTECTION + hex + default 0x0 if BAT6_ACCESS_NONE + default 0x1 if BAT6_ACCESS_RO + default 0x2 if BAT6_ACCESS_RW + +config BAT6_WIMG_ICACHE + hex + default 0x0 if !BAT6_ICACHE_WRITETHROUGH && !BAT6_ICACHE_INHIBITED && !BAT6_ICACHE_MEMORYCOHERENCE && !BAT6_ICACHE_GUARDED + default 0x8 if !BAT6_ICACHE_WRITETHROUGH && !BAT6_ICACHE_INHIBITED && !BAT6_ICACHE_MEMORYCOHERENCE && BAT6_ICACHE_GUARDED + default 0x10 if !BAT6_ICACHE_WRITETHROUGH && !BAT6_ICACHE_INHIBITED && BAT6_ICACHE_MEMORYCOHERENCE && !BAT6_ICACHE_GUARDED + default 0x18 if !BAT6_ICACHE_WRITETHROUGH && !BAT6_ICACHE_INHIBITED && BAT6_ICACHE_MEMORYCOHERENCE && BAT6_ICACHE_GUARDED + default 0x20 if !BAT6_ICACHE_WRITETHROUGH && BAT6_ICACHE_INHIBITED && !BAT6_ICACHE_MEMORYCOHERENCE && !BAT6_ICACHE_GUARDED + default 0x28 if !BAT6_ICACHE_WRITETHROUGH && BAT6_ICACHE_INHIBITED && !BAT6_ICACHE_MEMORYCOHERENCE && BAT6_ICACHE_GUARDED + default 0x30 if !BAT6_ICACHE_WRITETHROUGH && BAT6_ICACHE_INHIBITED && BAT6_ICACHE_MEMORYCOHERENCE && !BAT6_ICACHE_GUARDED + default 0x38 if !BAT6_ICACHE_WRITETHROUGH && BAT6_ICACHE_INHIBITED && BAT6_ICACHE_MEMORYCOHERENCE && BAT6_ICACHE_GUARDED + default 0x40 if BAT6_ICACHE_WRITETHROUGH && !BAT6_ICACHE_INHIBITED && !BAT6_ICACHE_MEMORYCOHERENCE && !BAT6_ICACHE_GUARDED + default 0x48 if BAT6_ICACHE_WRITETHROUGH && !BAT6_ICACHE_INHIBITED && !BAT6_ICACHE_MEMORYCOHERENCE && BAT6_ICACHE_GUARDED + default 0x50 if BAT6_ICACHE_WRITETHROUGH && !BAT6_ICACHE_INHIBITED && BAT6_ICACHE_MEMORYCOHERENCE && !BAT6_ICACHE_GUARDED + default 0x58 if BAT6_ICACHE_WRITETHROUGH && !BAT6_ICACHE_INHIBITED && BAT6_ICACHE_MEMORYCOHERENCE && BAT6_ICACHE_GUARDED + default 0x60 if BAT6_ICACHE_WRITETHROUGH && BAT6_ICACHE_INHIBITED && !BAT6_ICACHE_MEMORYCOHERENCE && !BAT6_ICACHE_GUARDED + default 0x68 if BAT6_ICACHE_WRITETHROUGH && BAT6_ICACHE_INHIBITED && !BAT6_ICACHE_MEMORYCOHERENCE && BAT6_ICACHE_GUARDED + default 0x70 if BAT6_ICACHE_WRITETHROUGH && BAT6_ICACHE_INHIBITED && BAT6_ICACHE_MEMORYCOHERENCE && !BAT6_ICACHE_GUARDED + default 0x78 if BAT6_ICACHE_WRITETHROUGH && BAT6_ICACHE_INHIBITED && BAT6_ICACHE_MEMORYCOHERENCE && BAT6_ICACHE_GUARDED + +config BAT6_WIMG_DCACHE + hex + default 0x0 if !BAT6_DCACHE_WRITETHROUGH && !BAT6_DCACHE_INHIBITED && !BAT6_DCACHE_MEMORYCOHERENCE && !BAT6_DCACHE_GUARDED + default 0x8 if !BAT6_DCACHE_WRITETHROUGH && !BAT6_DCACHE_INHIBITED && !BAT6_DCACHE_MEMORYCOHERENCE && BAT6_DCACHE_GUARDED + default 0x10 if !BAT6_DCACHE_WRITETHROUGH && !BAT6_DCACHE_INHIBITED && BAT6_DCACHE_MEMORYCOHERENCE && !BAT6_DCACHE_GUARDED + default 0x18 if !BAT6_DCACHE_WRITETHROUGH && !BAT6_DCACHE_INHIBITED && BAT6_DCACHE_MEMORYCOHERENCE && BAT6_DCACHE_GUARDED + default 0x20 if !BAT6_DCACHE_WRITETHROUGH && BAT6_DCACHE_INHIBITED && !BAT6_DCACHE_MEMORYCOHERENCE && !BAT6_DCACHE_GUARDED + default 0x28 if !BAT6_DCACHE_WRITETHROUGH && BAT6_DCACHE_INHIBITED && !BAT6_DCACHE_MEMORYCOHERENCE && BAT6_DCACHE_GUARDED + default 0x30 if !BAT6_DCACHE_WRITETHROUGH && BAT6_DCACHE_INHIBITED && BAT6_DCACHE_MEMORYCOHERENCE && !BAT6_DCACHE_GUARDED + default 0x38 if !BAT6_DCACHE_WRITETHROUGH && BAT6_DCACHE_INHIBITED && BAT6_DCACHE_MEMORYCOHERENCE && BAT6_DCACHE_GUARDED + default 0x40 if BAT6_DCACHE_WRITETHROUGH && !BAT6_DCACHE_INHIBITED && !BAT6_DCACHE_MEMORYCOHERENCE && !BAT6_DCACHE_GUARDED + default 0x48 if BAT6_DCACHE_WRITETHROUGH && !BAT6_DCACHE_INHIBITED && !BAT6_DCACHE_MEMORYCOHERENCE && BAT6_DCACHE_GUARDED + default 0x50 if BAT6_DCACHE_WRITETHROUGH && !BAT6_DCACHE_INHIBITED && BAT6_DCACHE_MEMORYCOHERENCE && !BAT6_DCACHE_GUARDED + default 0x58 if BAT6_DCACHE_WRITETHROUGH && !BAT6_DCACHE_INHIBITED && BAT6_DCACHE_MEMORYCOHERENCE && BAT6_DCACHE_GUARDED + default 0x60 if BAT6_DCACHE_WRITETHROUGH && BAT6_DCACHE_INHIBITED && !BAT6_DCACHE_MEMORYCOHERENCE && !BAT6_DCACHE_GUARDED + default 0x68 if BAT6_DCACHE_WRITETHROUGH && BAT6_DCACHE_INHIBITED && !BAT6_DCACHE_MEMORYCOHERENCE && BAT6_DCACHE_GUARDED + default 0x70 if BAT6_DCACHE_WRITETHROUGH && BAT6_DCACHE_INHIBITED && BAT6_DCACHE_MEMORYCOHERENCE && !BAT6_DCACHE_GUARDED + default 0x78 if BAT6_DCACHE_WRITETHROUGH && BAT6_DCACHE_INHIBITED && BAT6_DCACHE_MEMORYCOHERENCE && BAT6_DCACHE_GUARDED + +config BAT6_VALID_BITS + hex + default 0x0 if !BAT6_SUPERVISOR_MODE_VALID && !BAT6_USER_MODE_VALID + default 0x1 if !BAT6_SUPERVISOR_MODE_VALID && BAT6_USER_MODE_VALID + default 0x2 if BAT6_SUPERVISOR_MODE_VALID && !BAT6_USER_MODE_VALID + default 0x3 if BAT6_SUPERVISOR_MODE_VALID && BAT6_USER_MODE_VALID + +menuconfig BAT7 + bool "BAT7" + +if BAT7 + +config BAT7_NAME + string "Identifier" + +config BAT7_BASE + hex "Base" + +choice + prompt "Block length" + +config BAT7_LENGTH_128_KBYTES + bool "128 kb" + +config BAT7_LENGTH_256_KBYTES + bool "256 kb" + +config BAT7_LENGTH_512_KBYTES + bool "512 kb" + +config BAT7_LENGTH_1_MBYTES + bool "1 mb" + +config BAT7_LENGTH_2_MBYTES + bool "2 mb" + +config BAT7_LENGTH_4_MBYTES + bool "4 mb" + +config BAT7_LENGTH_8_MBYTES + bool "8 mb" + +config BAT7_LENGTH_16_MBYTES + bool "16 mb" + +config BAT7_LENGTH_32_MBYTES + bool "32 mb" + +config BAT7_LENGTH_64_MBYTES + bool "64 mb" + +config BAT7_LENGTH_128_MBYTES + bool "128 mb" + +config BAT7_LENGTH_256_MBYTES + bool "256 mb" +endchoice + +choice + prompt "Protection mode" + +config BAT7_ACCESS_NONE + bool "No access" + +config BAT7_ACCESS_RO + bool "Read-only" + +config BAT7_ACCESS_RW + bool "Read-write" + +endchoice + +config BAT7_ICACHE_WRITETHROUGH + bool "I-cache Write-through" + +config BAT7_ICACHE_INHIBITED + bool "I-cache Inhibited" + +config BAT7_ICACHE_MEMORYCOHERENCE + bool "I-cache Memory coherence" + +config BAT7_ICACHE_GUARDED + bool "I-cache Guarded" + +config BAT7_DCACHE_WRITETHROUGH + bool "D-cache Write-through" + +config BAT7_DCACHE_INHIBITED + bool "D-cache Inhibited" + +config BAT7_DCACHE_MEMORYCOHERENCE + bool "D-cache Memory coherence" + +config BAT7_DCACHE_GUARDED + bool "D-cache Guarded" + +config BAT7_USER_MODE_VALID + bool "User mode valid" + +config BAT7_SUPERVISOR_MODE_VALID + bool "Supervisor mode valid" + +endif + +config BAT7_LENGTH + hex + default 0x00000000 if BAT7_LENGTH_128_KBYTES + default 0x00000004 if BAT7_LENGTH_256_KBYTES + default 0x0000000c if BAT7_LENGTH_512_KBYTES + default 0x0000001c if BAT7_LENGTH_1_MBYTES + default 0x0000003c if BAT7_LENGTH_2_MBYTES + default 0x0000007c if BAT7_LENGTH_4_MBYTES + default 0x000000fc if BAT7_LENGTH_8_MBYTES + default 0x000001fc if BAT7_LENGTH_16_MBYTES + default 0x000003fc if BAT7_LENGTH_32_MBYTES + default 0x000007fc if BAT7_LENGTH_64_MBYTES + default 0x00000ffc if BAT7_LENGTH_128_MBYTES + default 0x00001ffc if BAT7_LENGTH_256_MBYTES + +config BAT7_PAGE_PROTECTION + hex + default 0x0 if BAT7_ACCESS_NONE + default 0x1 if BAT7_ACCESS_RO + default 0x2 if BAT7_ACCESS_RW + +config BAT7_WIMG_ICACHE + hex + default 0x0 if !BAT7_ICACHE_WRITETHROUGH && !BAT7_ICACHE_INHIBITED && !BAT7_ICACHE_MEMORYCOHERENCE && !BAT7_ICACHE_GUARDED + default 0x8 if !BAT7_ICACHE_WRITETHROUGH && !BAT7_ICACHE_INHIBITED && !BAT7_ICACHE_MEMORYCOHERENCE && BAT7_ICACHE_GUARDED + default 0x10 if !BAT7_ICACHE_WRITETHROUGH && !BAT7_ICACHE_INHIBITED && BAT7_ICACHE_MEMORYCOHERENCE && !BAT7_ICACHE_GUARDED + default 0x18 if !BAT7_ICACHE_WRITETHROUGH && !BAT7_ICACHE_INHIBITED && BAT7_ICACHE_MEMORYCOHERENCE && BAT7_ICACHE_GUARDED + default 0x20 if !BAT7_ICACHE_WRITETHROUGH && BAT7_ICACHE_INHIBITED && !BAT7_ICACHE_MEMORYCOHERENCE && !BAT7_ICACHE_GUARDED + default 0x28 if !BAT7_ICACHE_WRITETHROUGH && BAT7_ICACHE_INHIBITED && !BAT7_ICACHE_MEMORYCOHERENCE && BAT7_ICACHE_GUARDED + default 0x30 if !BAT7_ICACHE_WRITETHROUGH && BAT7_ICACHE_INHIBITED && BAT7_ICACHE_MEMORYCOHERENCE && !BAT7_ICACHE_GUARDED + default 0x38 if !BAT7_ICACHE_WRITETHROUGH && BAT7_ICACHE_INHIBITED && BAT7_ICACHE_MEMORYCOHERENCE && BAT7_ICACHE_GUARDED + default 0x40 if BAT7_ICACHE_WRITETHROUGH && !BAT7_ICACHE_INHIBITED && !BAT7_ICACHE_MEMORYCOHERENCE && !BAT7_ICACHE_GUARDED + default 0x48 if BAT7_ICACHE_WRITETHROUGH && !BAT7_ICACHE_INHIBITED && !BAT7_ICACHE_MEMORYCOHERENCE && BAT7_ICACHE_GUARDED + default 0x50 if BAT7_ICACHE_WRITETHROUGH && !BAT7_ICACHE_INHIBITED && BAT7_ICACHE_MEMORYCOHERENCE && !BAT7_ICACHE_GUARDED + default 0x58 if BAT7_ICACHE_WRITETHROUGH && !BAT7_ICACHE_INHIBITED && BAT7_ICACHE_MEMORYCOHERENCE && BAT7_ICACHE_GUARDED + default 0x60 if BAT7_ICACHE_WRITETHROUGH && BAT7_ICACHE_INHIBITED && !BAT7_ICACHE_MEMORYCOHERENCE && !BAT7_ICACHE_GUARDED + default 0x68 if BAT7_ICACHE_WRITETHROUGH && BAT7_ICACHE_INHIBITED && !BAT7_ICACHE_MEMORYCOHERENCE && BAT7_ICACHE_GUARDED + default 0x70 if BAT7_ICACHE_WRITETHROUGH && BAT7_ICACHE_INHIBITED && BAT7_ICACHE_MEMORYCOHERENCE && !BAT7_ICACHE_GUARDED + default 0x78 if BAT7_ICACHE_WRITETHROUGH && BAT7_ICACHE_INHIBITED && BAT7_ICACHE_MEMORYCOHERENCE && BAT7_ICACHE_GUARDED + +config BAT7_WIMG_DCACHE + hex + default 0x0 if !BAT7_DCACHE_WRITETHROUGH && !BAT7_DCACHE_INHIBITED && !BAT7_DCACHE_MEMORYCOHERENCE && !BAT7_DCACHE_GUARDED + default 0x8 if !BAT7_DCACHE_WRITETHROUGH && !BAT7_DCACHE_INHIBITED && !BAT7_DCACHE_MEMORYCOHERENCE && BAT7_DCACHE_GUARDED + default 0x10 if !BAT7_DCACHE_WRITETHROUGH && !BAT7_DCACHE_INHIBITED && BAT7_DCACHE_MEMORYCOHERENCE && !BAT7_DCACHE_GUARDED + default 0x18 if !BAT7_DCACHE_WRITETHROUGH && !BAT7_DCACHE_INHIBITED && BAT7_DCACHE_MEMORYCOHERENCE && BAT7_DCACHE_GUARDED + default 0x20 if !BAT7_DCACHE_WRITETHROUGH && BAT7_DCACHE_INHIBITED && !BAT7_DCACHE_MEMORYCOHERENCE && !BAT7_DCACHE_GUARDED + default 0x28 if !BAT7_DCACHE_WRITETHROUGH && BAT7_DCACHE_INHIBITED && !BAT7_DCACHE_MEMORYCOHERENCE && BAT7_DCACHE_GUARDED + default 0x30 if !BAT7_DCACHE_WRITETHROUGH && BAT7_DCACHE_INHIBITED && BAT7_DCACHE_MEMORYCOHERENCE && !BAT7_DCACHE_GUARDED + default 0x38 if !BAT7_DCACHE_WRITETHROUGH && BAT7_DCACHE_INHIBITED && BAT7_DCACHE_MEMORYCOHERENCE && BAT7_DCACHE_GUARDED + default 0x40 if BAT7_DCACHE_WRITETHROUGH && !BAT7_DCACHE_INHIBITED && !BAT7_DCACHE_MEMORYCOHERENCE && !BAT7_DCACHE_GUARDED + default 0x48 if BAT7_DCACHE_WRITETHROUGH && !BAT7_DCACHE_INHIBITED && !BAT7_DCACHE_MEMORYCOHERENCE && BAT7_DCACHE_GUARDED + default 0x50 if BAT7_DCACHE_WRITETHROUGH && !BAT7_DCACHE_INHIBITED && BAT7_DCACHE_MEMORYCOHERENCE && !BAT7_DCACHE_GUARDED + default 0x58 if BAT7_DCACHE_WRITETHROUGH && !BAT7_DCACHE_INHIBITED && BAT7_DCACHE_MEMORYCOHERENCE && BAT7_DCACHE_GUARDED + default 0x60 if BAT7_DCACHE_WRITETHROUGH && BAT7_DCACHE_INHIBITED && !BAT7_DCACHE_MEMORYCOHERENCE && !BAT7_DCACHE_GUARDED + default 0x68 if BAT7_DCACHE_WRITETHROUGH && BAT7_DCACHE_INHIBITED && !BAT7_DCACHE_MEMORYCOHERENCE && BAT7_DCACHE_GUARDED + default 0x70 if BAT7_DCACHE_WRITETHROUGH && BAT7_DCACHE_INHIBITED && BAT7_DCACHE_MEMORYCOHERENCE && !BAT7_DCACHE_GUARDED + default 0x78 if BAT7_DCACHE_WRITETHROUGH && BAT7_DCACHE_INHIBITED && BAT7_DCACHE_MEMORYCOHERENCE && BAT7_DCACHE_GUARDED + +config BAT7_VALID_BITS + hex + default 0x0 if !BAT7_SUPERVISOR_MODE_VALID && !BAT7_USER_MODE_VALID + default 0x1 if !BAT7_SUPERVISOR_MODE_VALID && BAT7_USER_MODE_VALID + default 0x2 if BAT7_SUPERVISOR_MODE_VALID && !BAT7_USER_MODE_VALID + default 0x3 if BAT7_SUPERVISOR_MODE_VALID && BAT7_USER_MODE_VALID + +endif + +endmenu diff --git a/arch/powerpc/cpu/mpc83xx/bats/bats.h b/arch/powerpc/cpu/mpc83xx/bats/bats.h new file mode 100644 index 0000000000..f0754c2351 --- /dev/null +++ b/arch/powerpc/cpu/mpc83xx/bats/bats.h @@ -0,0 +1,223 @@ +#ifdef CONFIG_BAT0 +#define CONFIG_SYS_IBAT0L (\ + (CONFIG_BAT0_BASE) |\ + (CONFIG_BAT0_PAGE_PROTECTION) |\ + (CONFIG_BAT0_WIMG_ICACHE) \ + ) +#define CONFIG_SYS_IBAT0U (\ + (CONFIG_BAT0_BASE) |\ + (CONFIG_BAT0_LENGTH) |\ + (CONFIG_BAT0_VALID_BITS) \ + ) +#define CONFIG_SYS_DBAT0L (\ + (CONFIG_BAT0_BASE) |\ + (CONFIG_BAT0_PAGE_PROTECTION) |\ + (CONFIG_BAT0_WIMG_DCACHE) \ + ) +#define CONFIG_SYS_DBAT0U (\ + (CONFIG_BAT0_BASE) |\ + (CONFIG_BAT0_LENGTH) |\ + (CONFIG_BAT0_VALID_BITS) \ + ) +#else +#define CONFIG_SYS_IBAT0L (0) +#define CONFIG_SYS_IBAT0U (0) +#define CONFIG_SYS_DBAT0L (0) +#define CONFIG_SYS_DBAT0U (0) +#endif /* CONFIG_BAT0 */ + +#ifdef CONFIG_BAT1 +#define CONFIG_SYS_IBAT1L (\ + (CONFIG_BAT1_BASE) |\ + (CONFIG_BAT1_PAGE_PROTECTION) |\ + (CONFIG_BAT1_WIMG_ICACHE) \ + ) +#define CONFIG_SYS_IBAT1U (\ + (CONFIG_BAT1_BASE) |\ + (CONFIG_BAT1_LENGTH) |\ + (CONFIG_BAT1_VALID_BITS) \ + ) +#define CONFIG_SYS_DBAT1L (\ + (CONFIG_BAT1_BASE) |\ + (CONFIG_BAT1_PAGE_PROTECTION) |\ + (CONFIG_BAT1_WIMG_DCACHE) \ + ) +#define CONFIG_SYS_DBAT1U (\ + (CONFIG_BAT1_BASE) |\ + (CONFIG_BAT1_LENGTH) |\ + (CONFIG_BAT1_VALID_BITS) \ + ) +#else +#define CONFIG_SYS_IBAT1L (0) +#define CONFIG_SYS_IBAT1U (0) +#define CONFIG_SYS_DBAT1L (0) +#define CONFIG_SYS_DBAT1U (0) +#endif /* CONFIG_BAT1 */ + +#ifdef CONFIG_BAT2 +#define CONFIG_SYS_IBAT2L (\ + (CONFIG_BAT2_BASE) |\ + (CONFIG_BAT2_PAGE_PROTECTION) |\ + (CONFIG_BAT2_WIMG_ICACHE) \ + ) +#define CONFIG_SYS_IBAT2U (\ + (CONFIG_BAT2_BASE) |\ + (CONFIG_BAT2_LENGTH) |\ + (CONFIG_BAT2_VALID_BITS) \ + ) +#define CONFIG_SYS_DBAT2L (\ + (CONFIG_BAT2_BASE) |\ + (CONFIG_BAT2_PAGE_PROTECTION) |\ + (CONFIG_BAT2_WIMG_DCACHE) \ + ) +#define CONFIG_SYS_DBAT2U (\ + (CONFIG_BAT2_BASE) |\ + (CONFIG_BAT2_LENGTH) |\ + (CONFIG_BAT2_VALID_BITS) \ + ) +#else +#define CONFIG_SYS_IBAT2L (0) +#define CONFIG_SYS_IBAT2U (0) +#define CONFIG_SYS_DBAT2L (0) +#define CONFIG_SYS_DBAT2U (0) +#endif /* CONFIG_BAT2 */ + +#ifdef CONFIG_BAT3 +#define CONFIG_SYS_IBAT3L (\ + (CONFIG_BAT3_BASE) |\ + (CONFIG_BAT3_PAGE_PROTECTION) |\ + (CONFIG_BAT3_WIMG_ICACHE) \ + ) +#define CONFIG_SYS_IBAT3U (\ + (CONFIG_BAT3_BASE) |\ + (CONFIG_BAT3_LENGTH) |\ + (CONFIG_BAT3_VALID_BITS) \ + ) +#define CONFIG_SYS_DBAT3L (\ + (CONFIG_BAT3_BASE) |\ + (CONFIG_BAT3_PAGE_PROTECTION) |\ + (CONFIG_BAT3_WIMG_DCACHE) \ + ) +#define CONFIG_SYS_DBAT3U (\ + (CONFIG_BAT3_BASE) |\ + (CONFIG_BAT3_LENGTH) |\ + (CONFIG_BAT3_VALID_BITS) \ + ) +#else +#define CONFIG_SYS_IBAT3L (0) +#define CONFIG_SYS_IBAT3U (0) +#define CONFIG_SYS_DBAT3L (0) +#define CONFIG_SYS_DBAT3U (0) +#endif /* CONFIG_BAT3 */ + +#ifdef CONFIG_BAT4 +#define CONFIG_SYS_IBAT4L (\ + (CONFIG_BAT4_BASE) |\ + (CONFIG_BAT4_PAGE_PROTECTION) |\ + (CONFIG_BAT4_WIMG_ICACHE) \ + ) +#define CONFIG_SYS_IBAT4U (\ + (CONFIG_BAT4_BASE) |\ + (CONFIG_BAT4_LENGTH) |\ + (CONFIG_BAT4_VALID_BITS) \ + ) +#define CONFIG_SYS_DBAT4L (\ + (CONFIG_BAT4_BASE) |\ + (CONFIG_BAT4_PAGE_PROTECTION) |\ + (CONFIG_BAT4_WIMG_DCACHE) \ + ) +#define CONFIG_SYS_DBAT4U (\ + (CONFIG_BAT4_BASE) |\ + (CONFIG_BAT4_LENGTH) |\ + (CONFIG_BAT4_VALID_BITS) \ + ) +#else +#define CONFIG_SYS_IBAT4L (0) +#define CONFIG_SYS_IBAT4U (0) +#define CONFIG_SYS_DBAT4L (0) +#define CONFIG_SYS_DBAT4U (0) +#endif /* CONFIG_BAT4 */ + +#ifdef CONFIG_BAT5 +#define CONFIG_SYS_IBAT5L (\ + (CONFIG_BAT5_BASE) |\ + (CONFIG_BAT5_PAGE_PROTECTION) |\ + (CONFIG_BAT5_WIMG_ICACHE) \ + ) +#define CONFIG_SYS_IBAT5U (\ + (CONFIG_BAT5_BASE) |\ + (CONFIG_BAT5_LENGTH) |\ + (CONFIG_BAT5_VALID_BITS) \ + ) +#define CONFIG_SYS_DBAT5L (\ + (CONFIG_BAT5_BASE) |\ + (CONFIG_BAT5_PAGE_PROTECTION) |\ + (CONFIG_BAT5_WIMG_DCACHE) \ + ) +#define CONFIG_SYS_DBAT5U (\ + (CONFIG_BAT5_BASE) |\ + (CONFIG_BAT5_LENGTH) |\ + (CONFIG_BAT5_VALID_BITS) \ + ) +#else +#define CONFIG_SYS_IBAT5L (0) +#define CONFIG_SYS_IBAT5U (0) +#define CONFIG_SYS_DBAT5L (0) +#define CONFIG_SYS_DBAT5U (0) +#endif /* CONFIG_BAT5 */ + +#ifdef CONFIG_BAT6 +#define CONFIG_SYS_IBAT6L (\ + (CONFIG_BAT6_BASE) |\ + (CONFIG_BAT6_PAGE_PROTECTION) |\ + (CONFIG_BAT6_WIMG_ICACHE) \ + ) +#define CONFIG_SYS_IBAT6U (\ + (CONFIG_BAT6_BASE) |\ + (CONFIG_BAT6_LENGTH) |\ + (CONFIG_BAT6_VALID_BITS) \ + ) +#define CONFIG_SYS_DBAT6L (\ + (CONFIG_BAT6_BASE) |\ + (CONFIG_BAT6_PAGE_PROTECTION) |\ + (CONFIG_BAT6_WIMG_DCACHE) \ + ) +#define CONFIG_SYS_DBAT6U (\ + (CONFIG_BAT6_BASE) |\ + (CONFIG_BAT6_LENGTH) |\ + (CONFIG_BAT6_VALID_BITS) \ + ) +#else +#define CONFIG_SYS_IBAT6L (0) +#define CONFIG_SYS_IBAT6U (0) +#define CONFIG_SYS_DBAT6L (0) +#define CONFIG_SYS_DBAT6U (0) +#endif /* CONFIG_BAT6 */ + +#ifdef CONFIG_BAT7 +#define CONFIG_SYS_IBAT7L (\ + (CONFIG_BAT7_BASE) |\ + (CONFIG_BAT7_PAGE_PROTECTION) |\ + (CONFIG_BAT7_WIMG_ICACHE) \ + ) +#define CONFIG_SYS_IBAT7U (\ + (CONFIG_BAT7_BASE) |\ + (CONFIG_BAT7_LENGTH) |\ + (CONFIG_BAT7_VALID_BITS) \ + ) +#define CONFIG_SYS_DBAT7L (\ + (CONFIG_BAT7_BASE) |\ + (CONFIG_BAT7_PAGE_PROTECTION) |\ + (CONFIG_BAT7_WIMG_DCACHE) \ + ) +#define CONFIG_SYS_DBAT7U (\ + (CONFIG_BAT7_BASE) |\ + (CONFIG_BAT7_LENGTH) |\ + (CONFIG_BAT7_VALID_BITS) \ + ) +#else +#define CONFIG_SYS_IBAT7L (0) +#define CONFIG_SYS_IBAT7U (0) +#define CONFIG_SYS_DBAT7L (0) +#define CONFIG_SYS_DBAT7U (0) +#endif /* CONFIG_BAT7 */ diff --git a/arch/powerpc/cpu/mpc83xx/cpu.c b/arch/powerpc/cpu/mpc83xx/cpu.c index b29f271e9b..3048ecf34a 100644 --- a/arch/powerpc/cpu/mpc83xx/cpu.c +++ b/arch/powerpc/cpu/mpc83xx/cpu.c @@ -18,7 +18,7 @@ #include <tsec.h> #include <netdev.h> #include <fsl_esdhc.h> -#if defined(CONFIG_BOOTCOUNT_LIMIT) && !defined(CONFIG_MPC831x) +#if defined(CONFIG_BOOTCOUNT_LIMIT) && !defined(CONFIG_ARCH_MPC831X) #include <linux/immap_qe.h> #include <asm/io.h> #endif @@ -133,18 +133,18 @@ do_reset (cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[]) #ifdef MPC83xx_RESET /* Interrupts and MMU off */ - __asm__ __volatile__ ("mfmsr %0":"=r" (msr):); - - msr &= ~( MSR_EE | MSR_IR | MSR_DR); - __asm__ __volatile__ ("mtmsr %0"::"r" (msr)); + msr = mfmsr(); + msr &= ~(MSR_EE | MSR_IR | MSR_DR); + mtmsr(msr); /* enable Reset Control Reg */ immap->reset.rpr = 0x52535445; - __asm__ __volatile__ ("sync"); - __asm__ __volatile__ ("isync"); + sync(); + isync(); /* confirm Reset Control Reg is enabled */ - while(!((immap->reset.rcer) & RCER_CRE)); + while(!((immap->reset.rcer) & RCER_CRE)) + ; udelay(200); @@ -156,10 +156,9 @@ do_reset (cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[]) immap->reset.rmr = RMR_CSRE; /* Checkstop Reset enable */ /* Interrupts and MMU off */ - __asm__ __volatile__ ("mfmsr %0":"=r" (msr):); - + msr = mfmsr(); msr &= ~(MSR_ME | MSR_EE | MSR_IR | MSR_DR); - __asm__ __volatile__ ("mtmsr %0"::"r" (msr)); + mtmsr(msr); /* * Trying to execute the next instruction at a non-existing address @@ -199,6 +198,7 @@ void watchdog_reset (void) } #endif +#ifndef CONFIG_DM_ETH /* * Initializes on-chip ethernet controllers. * to override, implement board_eth_init() @@ -214,6 +214,7 @@ int cpu_eth_init(bd_t *bis) #endif return 0; } +#endif /* !CONFIG_DM_ETH */ /* * Initializes on-chip MMC controllers. @@ -227,3 +228,21 @@ int cpu_mmc_init(bd_t *bis) return 0; #endif } + +void ppcDWstore(unsigned int *addr, unsigned int *value) +{ + asm("lfd 1, 0(%1)\n\t" + "stfd 1, 0(%0)" + : + : "r" (addr), "r" (value) + : "memory"); +} + +void ppcDWload(unsigned int *addr, unsigned int *ret) +{ + asm("lfd 1, 0(%0)\n\t" + "stfd 1, 0(%1)" + : + : "r" (addr), "r" (ret) + : "memory"); +} diff --git a/arch/powerpc/cpu/mpc83xx/cpu_init.c b/arch/powerpc/cpu/mpc83xx/cpu_init.c index 1555205e06..af8facad53 100644 --- a/arch/powerpc/cpu/mpc83xx/cpu_init.c +++ b/arch/powerpc/cpu/mpc83xx/cpu_init.c @@ -12,6 +12,12 @@ #include <usb/ehci-ci.h> #endif +#include "lblaw/lblaw.h" +#include "elbc/elbc.h" +#include "sysio/sysio.h" +#include "arbiter/arbiter.h" +#include "initreg/initreg.h" + DECLARE_GLOBAL_DATA_PTR; #ifdef CONFIG_QE @@ -47,62 +53,6 @@ static void config_qe_ioports(void) */ void cpu_init_f (volatile immap_t * im) { - __be32 acr_mask = -#ifdef CONFIG_SYS_ACR_PIPE_DEP /* Arbiter pipeline depth */ - ACR_PIPE_DEP | -#endif -#ifdef CONFIG_SYS_ACR_RPTCNT /* Arbiter repeat count */ - ACR_RPTCNT | -#endif -#ifdef CONFIG_SYS_ACR_APARK /* Arbiter address parking mode */ - ACR_APARK | -#endif -#ifdef CONFIG_SYS_ACR_PARKM /* Arbiter parking master */ - ACR_PARKM | -#endif - 0; - __be32 acr_val = -#ifdef CONFIG_SYS_ACR_PIPE_DEP /* Arbiter pipeline depth */ - (CONFIG_SYS_ACR_PIPE_DEP << ACR_PIPE_DEP_SHIFT) | -#endif -#ifdef CONFIG_SYS_ACR_RPTCNT /* Arbiter repeat count */ - (CONFIG_SYS_ACR_RPTCNT << ACR_RPTCNT_SHIFT) | -#endif -#ifdef CONFIG_SYS_ACR_APARK /* Arbiter address parking mode */ - (CONFIG_SYS_ACR_APARK << ACR_APARK_SHIFT) | -#endif -#ifdef CONFIG_SYS_ACR_PARKM /* Arbiter parking master */ - (CONFIG_SYS_ACR_PARKM << ACR_PARKM_SHIFT) | -#endif - 0; - __be32 spcr_mask = -#ifdef CONFIG_SYS_SPCR_OPT /* Optimize transactions between CSB and other dev */ - SPCR_OPT | -#endif -#ifdef CONFIG_SYS_SPCR_TSECEP /* all eTSEC's Emergency priority */ - SPCR_TSECEP | -#endif -#ifdef CONFIG_SYS_SPCR_TSEC1EP /* TSEC1 Emergency priority */ - SPCR_TSEC1EP | -#endif -#ifdef CONFIG_SYS_SPCR_TSEC2EP /* TSEC2 Emergency priority */ - SPCR_TSEC2EP | -#endif - 0; - __be32 spcr_val = -#ifdef CONFIG_SYS_SPCR_OPT - (CONFIG_SYS_SPCR_OPT << SPCR_OPT_SHIFT) | -#endif -#ifdef CONFIG_SYS_SPCR_TSECEP /* all eTSEC's Emergency priority */ - (CONFIG_SYS_SPCR_TSECEP << SPCR_TSECEP_SHIFT) | -#endif -#ifdef CONFIG_SYS_SPCR_TSEC1EP /* TSEC1 Emergency priority */ - (CONFIG_SYS_SPCR_TSEC1EP << SPCR_TSEC1EP_SHIFT) | -#endif -#ifdef CONFIG_SYS_SPCR_TSEC2EP /* TSEC2 Emergency priority */ - (CONFIG_SYS_SPCR_TSEC2EP << SPCR_TSEC2EP_SHIFT) | -#endif - 0; __be32 sccr_mask = #ifdef CONFIG_SYS_SCCR_ENCCM /* Encryption clock mode */ SCCR_ENCCM | @@ -179,28 +129,6 @@ void cpu_init_f (volatile immap_t * im) (CONFIG_SYS_SCCR_SATACM << SCCR_SATACM_SHIFT) | #endif 0; - __be32 lcrr_mask = -#ifdef CONFIG_SYS_LCRR_DBYP /* PLL bypass */ - LCRR_DBYP | -#endif -#ifdef CONFIG_SYS_LCRR_EADC /* external address delay */ - LCRR_EADC | -#endif -#ifdef CONFIG_SYS_LCRR_CLKDIV /* system clock divider */ - LCRR_CLKDIV | -#endif - 0; - __be32 lcrr_val = -#ifdef CONFIG_SYS_LCRR_DBYP /* PLL bypass */ - CONFIG_SYS_LCRR_DBYP | -#endif -#ifdef CONFIG_SYS_LCRR_EADC - CONFIG_SYS_LCRR_EADC | -#endif -#ifdef CONFIG_SYS_LCRR_CLKDIV /* system clock divider */ - CONFIG_SYS_LCRR_CLKDIV | -#endif - 0; /* Pointer is writable since we allocated a register for it */ gd = (gd_t *) (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET); @@ -240,7 +168,7 @@ void cpu_init_f (volatile immap_t * im) /* System General Purpose Register */ #ifdef CONFIG_SYS_SICRH -#if defined(CONFIG_MPC834x) || defined(CONFIG_MPC8313) +#if defined(CONFIG_ARCH_MPC834X) || defined(CONFIG_ARCH_MPC8313) /* regarding to MPC34x manual rev.1 bits 28..29 must be preserved */ __raw_writel((im->sysconf.sicrh & 0x0000000C) | CONFIG_SYS_SICRH, &im->sysconf.sicrh); @@ -312,7 +240,7 @@ void cpu_init_f (volatile immap_t * im) im->gpio[1].dat = CONFIG_SYS_GPIO2_DAT; im->gpio[1].dir = CONFIG_SYS_GPIO2_DIR; #endif -#if defined(CONFIG_USB_EHCI_FSL) && defined(CONFIG_MPC831x) +#if defined(CONFIG_USB_EHCI_FSL) && defined(CONFIG_ARCH_MPC831X) uint32_t temp; struct usb_ehci *ehci = (struct usb_ehci *)CONFIG_SYS_FSL_USB1_ADDR; diff --git a/arch/powerpc/cpu/mpc83xx/ecc.c b/arch/powerpc/cpu/mpc83xx/ecc.c index 73f0be2a30..10e9b96add 100644 --- a/arch/powerpc/cpu/mpc83xx/ecc.c +++ b/arch/powerpc/cpu/mpc83xx/ecc.c @@ -191,8 +191,8 @@ int do_ecc(cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[]) } ddr->err_disable = val; - __asm__ __volatile__("sync"); - __asm__ __volatile__("isync"); + sync(); + isync(); return 0; } else if (strcmp(argv[1], "errdetectclr") == 0) { val = ddr->err_detect; @@ -249,8 +249,8 @@ int do_ecc(cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[]) printf("Incorrect command\n"); ddr->ecc_err_inject = val; - __asm__ __volatile__("sync"); - __asm__ __volatile__("isync"); + sync(); + isync(); return 0; } else if (strcmp(argv[1], "mirror") == 0) { val = ddr->ecc_err_inject; @@ -282,26 +282,26 @@ int do_ecc(cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[]) /* enable injects */ ddr->ecc_err_inject |= ECC_ERR_INJECT_EIEN; - __asm__ __volatile__("sync"); - __asm__ __volatile__("isync"); + sync(); + isync(); /* write memory location injecting errors */ ppcDWstore((u32 *) i, pattern); - __asm__ __volatile__("sync"); + sync(); /* disable injects */ ddr->ecc_err_inject &= ~ECC_ERR_INJECT_EIEN; - __asm__ __volatile__("sync"); - __asm__ __volatile__("isync"); + sync(); + isync(); /* read data, this generates ECC error */ ppcDWload((u32 *) i, ret); - __asm__ __volatile__("sync"); + sync(); /* re-initialize memory, double word write the location again, * generates new ECC code this time */ ppcDWstore((u32 *) i, writeback); - __asm__ __volatile__("sync"); + sync(); } enable_interrupts(); return 0; @@ -321,29 +321,29 @@ int do_ecc(cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[]) /* enable injects */ ddr->ecc_err_inject |= ECC_ERR_INJECT_EIEN; - __asm__ __volatile__("sync"); - __asm__ __volatile__("isync"); + sync(); + isync(); /* write memory location injecting errors */ *(u32 *) i = 0xfedcba98UL; - __asm__ __volatile__("sync"); + sync(); /* sub double word write, * bus will read-modify-write, * generates ECC error */ *((u32 *) i + 1) = 0x76543210UL; - __asm__ __volatile__("sync"); + sync(); /* disable injects */ ddr->ecc_err_inject &= ~ECC_ERR_INJECT_EIEN; - __asm__ __volatile__("sync"); - __asm__ __volatile__("isync"); + sync(); + isync(); /* re-initialize memory, * double word write the location again, * generates new ECC code this time */ ppcDWstore((u32 *) i, writeback); - __asm__ __volatile__("sync"); + sync(); } enable_interrupts(); return 0; diff --git a/arch/powerpc/cpu/mpc83xx/elbc/Kconfig b/arch/powerpc/cpu/mpc83xx/elbc/Kconfig new file mode 100644 index 0000000000..74c4ff3ed4 --- /dev/null +++ b/arch/powerpc/cpu/mpc83xx/elbc/Kconfig @@ -0,0 +1,32 @@ +menu "ELBC register setup" + +choice + prompt "OR/BR for NAND SPL" + +config ELBC_BR_OR_NAND_PRELIM_NONE + bool "None" + +config ELBC_BR_OR_NAND_PRELIM_0 + bool "0" + +config ELBC_BR_OR_NAND_PRELIM_1 + bool "1" + +config ELBC_BR_OR_NAND_PRELIM_2 + bool "2" + +config ELBC_BR_OR_NAND_PRELIM_3 + bool "3" + +config ELBC_BR_OR_NAND_PRELIM_4 + bool "4" + +endchoice + +source "arch/powerpc/cpu/mpc83xx/elbc/Kconfig.elbc0" +source "arch/powerpc/cpu/mpc83xx/elbc/Kconfig.elbc1" +source "arch/powerpc/cpu/mpc83xx/elbc/Kconfig.elbc2" +source "arch/powerpc/cpu/mpc83xx/elbc/Kconfig.elbc3" +source "arch/powerpc/cpu/mpc83xx/elbc/Kconfig.elbc4" + +endmenu diff --git a/arch/powerpc/cpu/mpc83xx/elbc/Kconfig.elbc0 b/arch/powerpc/cpu/mpc83xx/elbc/Kconfig.elbc0 new file mode 100644 index 0000000000..23e81ab0bf --- /dev/null +++ b/arch/powerpc/cpu/mpc83xx/elbc/Kconfig.elbc0 @@ -0,0 +1,733 @@ +menuconfig ELBC_BR0_OR0 + bool "ELBC BR0/OR0" + +if ELBC_BR0_OR0 + +config BR0_OR0_NAME + string "Identifier" + +config BR0_OR0_BASE + hex "Port base" + +choice + prompt "Port size" + +config BR0_PORTSIZE_8BIT + bool "8-bit" + +config BR0_PORTSIZE_16BIT + depends on !BR0_MACHINE_FCM + bool "16-bit" + + +config BR0_PORTSIZE_32BIT + depends on !BR0_MACHINE_FCM + depends on ARCH_MPC8349 || ARCH_MPC8360 || ARCH_MPC8379 + bool "32-bit" + +endchoice + +if BR0_MACHINE_FCM + +choice + prompt "Data Error Checking" + +config BR0_ERRORCHECKING_DISABLED + bool "Disabled" + +config BR0_ERRORCHECKING_ECC_CHECKING + bool "ECC checking / No ECC generation" + +config BR0_ERRORCHECKING_BOTH + bool "ECC checking and generation" + +endchoice + +endif + +config BR0_WRITE_PROTECT + bool "Write-protect" + +config BR0_MACHINE_UPM + bool + +choice + prompt "Machine select" + +config BR0_MACHINE_GPCM + bool "GPCM" + +config BR0_MACHINE_FCM + depends on !ARCH_MPC832X && !ARCH_MPC8349 && !ARCH_MPC8360 + bool "FCM" + +config BR0_MACHINE_SDRAM + depends on ARCH_MPC8349 || ARCH_MPC8360 + bool "SDRAM" + +config BR0_MACHINE_UPMA + select BR0_MACHINE_UPM + bool "UPM (A)" + +config BR0_MACHINE_UPMB + select BR0_MACHINE_UPM + bool "UPM (B)" + +config BR0_MACHINE_UPMC + select BR0_MACHINE_UPM + bool "UPM (C)" + +endchoice + +if ARCH_MPC8313 || ARCH_MPC8323 || ARCH_MPC8360 + +choice + prompt "Atomic operations" + +config BR0_ATOMIC_NONE + bool "No atomic operations" + +config BR0_ATOMIC_RAWA + bool "Read-after-write-atomic" + +config BR0_ATOMIC_WARA + bool "Write-after-read-atomic" + +endchoice + +endif + +if BR0_MACHINE_GPCM || BR0_MACHINE_FCM || BR0_MACHINE_UPM || BR0_MACHINE_SDRAM + +choice + prompt "Address mask" + +config OR0_AM_32_KBYTES + depends on !BR0_MACHINE_SDRAM + bool "32 kb" + +config OR0_AM_64_KBYTES + bool "64 kb" + +config OR0_AM_128_KBYTES + bool "128 kb" + +config OR0_AM_256_KBYTES + bool "256 kb" + +config OR0_AM_512_KBYTES + bool "512 kb" + +config OR0_AM_1_MBYTES + bool "1 mb" + +config OR0_AM_2_MBYTES + bool "2 mb" + +config OR0_AM_4_MBYTES + bool "4 mb" + +config OR0_AM_8_MBYTES + bool "8 mb" + +config OR0_AM_16_MBYTES + bool "16 mb" + +config OR0_AM_32_MBYTES + bool "32 mb" + +config OR0_AM_64_MBYTES + bool "64 mb" + +# XXX: Some boards define 128MB AM with GPCM, even though it should not be +# possible according to the manuals +config OR0_AM_128_MBYTES + bool "128 mb" + +# XXX: Some boards define 256MB AM with GPCM, even though it should not be +# possible according to the manuals +config OR0_AM_256_MBYTES + bool "256 mb" + +config OR0_AM_512_MBYTES + depends on BR0_MACHINE_FCM + bool "512 mb" + +# XXX: Some boards define 1GB AM with GPCM, even though it should not be +# possible according to the manuals +config OR0_AM_1_GBYTES + bool "1 gb" + +config OR0_AM_2_GBYTES + depends on BR0_MACHINE_FCM + bool "2 gb" + +config OR0_AM_4_GBYTES + depends on BR0_MACHINE_FCM + bool "4 gb" + +endchoice + +config OR0_XAM_SET + bool "Set unused bytes after address mask" +choice + prompt "Buffer control disable" + +config OR0_BCTLD_ASSERTED + bool "Asserted" + +config OR0_BCTLD_NOT_ASSERTED + bool "Not asserted" + +endchoice + +endif + +if BR0_MACHINE_GPCM || BR0_MACHINE_FCM + +choice + prompt "Cycle length in bus clocks" + +config OR0_SCY_0 + bool "No wait states" + +config OR0_SCY_1 + bool "1 wait state" + +config OR0_SCY_2 + bool "2 wait states" + +config OR0_SCY_3 + bool "3 wait states" + +config OR0_SCY_4 + bool "4 wait states" + +config OR0_SCY_5 + bool "5 wait states" + +config OR0_SCY_6 + bool "6 wait states" + +config OR0_SCY_7 + bool "7 wait states" + +config OR0_SCY_8 + depends on BR0_MACHINE_GPCM + bool "8 wait states" + +config OR0_SCY_9 + depends on BR0_MACHINE_GPCM + bool "9 wait states" + +config OR0_SCY_10 + depends on BR0_MACHINE_GPCM + bool "10 wait states" + +config OR0_SCY_11 + depends on BR0_MACHINE_GPCM + bool "11 wait states" + +config OR0_SCY_12 + depends on BR0_MACHINE_GPCM + bool "12 wait states" + +config OR0_SCY_13 + depends on BR0_MACHINE_GPCM + bool "13 wait states" + +config OR0_SCY_14 + depends on BR0_MACHINE_GPCM + bool "14 wait states" + +config OR0_SCY_15 + depends on BR0_MACHINE_GPCM + bool "15 wait states" + +endchoice + +endif # BR0_MACHINE_GPCM || BR0_MACHINE_FCM + +if BR0_MACHINE_GPCM + +choice + prompt "Chip select negotiation time" + +config OR0_CSNT_NORMAL + bool "Normal" + +config OR0_CSNT_EARLIER + bool "Earlier" + +endchoice + +choice + prompt "Address to chip-select setup" + +config OR0_ACS_SAME_TIME + bool "At the same time" + +config OR0_ACS_HALF_CYCLE_EARLIER + bool "Half of a bus clock cycle earlier" + +config OR0_ACS_QUARTER_CYCLE_EARLIER + bool "Half/Quarter of a bus clock cycle earlier" + +endchoice + +choice + prompt "Extra address to check-select setup" + +config OR0_XACS_NORMAL + bool "Normal" + +config OR0_XACS_EXTENDED + bool "Extended" + +endchoice + +choice + prompt "External address termination" + +config OR0_SETA_INTERNAL + bool "Access is terminated internally" + +config OR0_SETA_EXTERNAL + bool "Access is terminated externally" + +endchoice + +endif # BR0_MACHINE_GPCM + +if BR0_MACHINE_FCM + +choice + prompt "NAND Flash EEPROM page size" + +config OR0_PGS_SMALL + bool "Small page device" + +config OR0_PGS_LARGE + bool "Large page device" + +endchoice + +choice + prompt "Chip select to command time" + +config OR0_CSCT_1_CYCLE + depends on OR0_TRLX_NORMAL + bool "1 cycle" + +config OR0_CSCT_2_CYCLE + depends on OR0_TRLX_RELAXED + bool "2 cycles" + +config OR0_CSCT_4_CYCLE + depends on OR0_TRLX_NORMAL + bool "4 cycles" + +config OR0_CSCT_8_CYCLE + depends on OR0_TRLX_RELAXED + bool "8 cycles" + +endchoice + +choice + prompt "Command setup time" + +config OR0_CST_COINCIDENT + depends on OR0_TRLX_NORMAL + bool "Coincident with any command" + +config OR0_CST_QUARTER_CLOCK + depends on OR0_TRLX_NORMAL + bool "0.25 clocks after" + +config OR0_CST_HALF_CLOCK + depends on OR0_TRLX_RELAXED + bool "0.5 clocks after" + +config OR0_CST_ONE_CLOCK + depends on OR0_TRLX_RELAXED + bool "1 clock after" + +endchoice + +choice + prompt "Command hold time" + +config OR0_CHT_HALF_CLOCK + depends on OR0_TRLX_NORMAL + bool "0.5 clocks before" + +config OR0_CHT_ONE_CLOCK + depends on OR0_TRLX_NORMAL + bool "1 clock before" + +config OR0_CHT_ONE_HALF_CLOCK + depends on OR0_TRLX_RELAXED + bool "1.5 clocks before" + +config OR0_CHT_TWO_CLOCK + depends on OR0_TRLX_RELAXED + bool "2 clocks before" + +endchoice + +choice + prompt "Reset setup time" + +config OR0_RST_THREE_QUARTER_CLOCK + depends on OR0_TRLX_NORMAL + bool "0.75 clocks prior" + +config OR0_RST_ONE_HALF_CLOCK + depends on OR0_TRLX_RELAXED + bool "0.5 clocks prior" + +config OR0_RST_ONE_CLOCK + bool "1 clock prior" + +endchoice + +endif # BR0_MACHINE_FCM + +if BR0_MACHINE_UPM + +choice + prompt "Burst inhibit" + +config OR0_BI_BURSTSUPPORT + bool "Support burst access" + +config OR0_BI_BURSTINHIBIT + bool "Inhibit burst access" + +endchoice + +endif # BR0_MACHINE_UPM + +if BR0_MACHINE_SDRAM + +choice + prompt "Number of column address lines" + +config OR0_COLS_7 + bool "7" + +config OR0_COLS_8 + bool "8" + +config OR0_COLS_9 + bool "9" + +config OR0_COLS_10 + bool "10" + +config OR0_COLS_11 + bool "11" + +config OR0_COLS_12 + bool "12" + +config OR0_COLS_13 + bool "13" + +config OR0_COLS_14 + bool "14" + +endchoice + +choice + prompt "Number of rows address lines" + +config OR0_ROWS_9 + bool "9" + +config OR0_ROWS_10 + bool "10" + +config OR0_ROWS_11 + bool "11" + +config OR0_ROWS_12 + bool "12" + +config OR0_ROWS_13 + bool "13" + +config OR0_ROWS_14 + bool "14" + +config OR0_ROWS_15 + bool "15" + +endchoice + +choice + prompt "Page mode select" + +config OR0_PMSEL_BTB + bool "Back-to-back" + +config OR0_PMSEL_KEPT_OPEN + bool "Page kept open until page miss or refresh" + +endchoice + +endif # BR0_MACHINE_SDRAM + +choice + prompt "Relaxed timing" + +config OR0_TRLX_NORMAL + bool "Normal" + +config OR0_TRLX_RELAXED + bool "Relaxed" + +endchoice + +choice + prompt "Extended hold time" + +config OR0_EHTR_NORMAL + depends on OR0_TRLX_NORMAL + bool "Normal" + +config OR0_EHTR_1_CYCLE + depends on OR0_TRLX_NORMAL + bool "1 idle clock cycle inserted" + +config OR0_EHTR_4_CYCLE + depends on OR0_TRLX_RELAXED + bool "4 idle clock cycles inserted" + +config OR0_EHTR_8_CYCLE + depends on OR0_TRLX_RELAXED + bool "8 idle clock cycles inserted" + +endchoice + +if !ARCH_MPC8308 + +choice + prompt "External address latch delay" + +config OR0_EAD_NONE + bool "None" + +config OR0_EAD_EXTRA + bool "Extra" + +endchoice + +endif # !ARCH_MPC8308 + +endif # ELBC_BR0_OR0 + +config BR0_PORTSIZE + hex + default 0x800 if BR0_PORTSIZE_8BIT + default 0x1000 if BR0_PORTSIZE_16BIT + default 0x1800 if BR0_PORTSIZE_32BIT + +config BR0_ERRORCHECKING + hex + default 0x0 if !BR0_MACHINE_FCM + default 0x0 if BR0_ERRORCHECKING_DISABLED + default 0x200 if BR0_ERRORCHECKING_ECC_CHECKING + default 0x400 if BR0_ERRORCHECKING_BOTH + +config BR0_WRITE_PROTECT_BIT + hex + default 0x0 if !BR0_WRITE_PROTECT + default 0x100 if BR0_WRITE_PROTECT + +config BR0_MACHINE + hex + default 0x0 if BR0_MACHINE_GPCM + default 0x20 if BR0_MACHINE_FCM + default 0x60 if BR0_MACHINE_SDRAM + default 0x80 if BR0_MACHINE_UPMA + default 0xa0 if BR0_MACHINE_UPMB + default 0xc0 if BR0_MACHINE_UPMC + +config BR0_ATOMIC + hex + default 0x0 if !ARCH_MPC8313 && !ARCH_MPC8323 && !ARCH_MPC8360 + default 0x0 if BR0_ATOMIC_NONE + default 0x4 if BR0_ATOMIC_RAWA + default 0x8 if BR0_ATOMIC_WARA + +config BR0_VALID_BIT + hex + default 0x0 if !ELBC_BR0_OR0 + default 0x1 if ELBC_BR0_OR0 + +config OR0_AM + hex + default 0xffff8000 if OR0_AM_32_KBYTES && !BR0_MACHINE_SDRAM + default 0xffff0000 if OR0_AM_64_KBYTES + default 0xfffe0000 if OR0_AM_128_KBYTES + default 0xfffc0000 if OR0_AM_256_KBYTES + default 0xfff80000 if OR0_AM_512_KBYTES + default 0xfff00000 if OR0_AM_1_MBYTES + default 0xffe00000 if OR0_AM_2_MBYTES + default 0xffc00000 if OR0_AM_4_MBYTES + default 0xff800000 if OR0_AM_8_MBYTES + default 0xff000000 if OR0_AM_16_MBYTES + default 0xfe000000 if OR0_AM_32_MBYTES + default 0xfc000000 if OR0_AM_64_MBYTES + default 0xf8000000 if OR0_AM_128_MBYTES + default 0xf0000000 if OR0_AM_256_MBYTES + default 0xe0000000 if OR0_AM_512_MBYTES + default 0xc0000000 if OR0_AM_1_GBYTES + default 0x80000000 if OR0_AM_2_GBYTES + default 0x00000000 if OR0_AM_4_GBYTES + +config OR0_XAM + hex + default 0x0 if !OR0_XAM_SET + default 0x6000 if OR0_XAM_SET + +config OR0_BCTLD + hex + default 0x0 if OR0_BCTLD_ASSERTED + default 0x1000 if OR0_BCTLD_NOT_ASSERTED + +config OR0_BI + hex + default 0x0 if !BR0_MACHINE_UPM + default 0x0 if OR0_BI_BURSTSUPPORT + default 0x100 if OR0_BI_BURSTINHIBIT + +config OR0_COLS + hex + default 0x0 if !BR0_MACHINE_SDRAM + default 0x0 if OR0_COLS_7 + default 0x400 if OR0_COLS_8 + default 0x800 if OR0_COLS_9 + default 0xc00 if OR0_COLS_10 + default 0x1000 if OR0_COLS_11 + default 0x1400 if OR0_COLS_12 + default 0x1800 if OR0_COLS_13 + default 0x1c00 if OR0_COLS_14 + +config OR0_ROWS + hex + default 0x0 if !BR0_MACHINE_SDRAM + default 0x0 if OR0_ROWS_9 + default 0x40 if OR0_ROWS_10 + default 0x80 if OR0_ROWS_11 + default 0xc0 if OR0_ROWS_12 + default 0x100 if OR0_ROWS_13 + default 0x140 if OR0_ROWS_14 + default 0x180 if OR0_ROWS_15 + +config OR0_PMSEL + hex + default 0x0 if !BR0_MACHINE_SDRAM + default 0x0 if OR0_PMSEL_BTB + default 0x20 if OR0_PMSEL_KEPT_OPEN + +config OR0_SCY + hex + default 0x0 if !BR0_MACHINE_GPCM && !BR0_MACHINE_FCM + default 0x0 if OR0_SCY_0 + default 0x10 if OR0_SCY_1 + default 0x20 if OR0_SCY_2 + default 0x30 if OR0_SCY_3 + default 0x40 if OR0_SCY_4 + default 0x50 if OR0_SCY_5 + default 0x60 if OR0_SCY_6 + default 0x70 if OR0_SCY_7 + default 0x80 if OR0_SCY_8 + default 0x90 if OR0_SCY_9 + default 0xa0 if OR0_SCY_10 + default 0xb0 if OR0_SCY_11 + default 0xc0 if OR0_SCY_12 + default 0xd0 if OR0_SCY_13 + default 0xe0 if OR0_SCY_14 + default 0xf0 if OR0_SCY_15 + +config OR0_PGS + hex + default 0x0 if !BR0_MACHINE_FCM + default 0x0 if OR0_PGS_SMALL + default 0x400 if OR0_PGS_LARGE + +config OR0_CSCT + hex + default 0x0 if !BR0_MACHINE_FCM + default 0x0 if OR0_CSCT_1_CYCLE + default 0x0 if OR0_CSCT_2_CYCLE + default 0x200 if OR0_CSCT_4_CYCLE + default 0x200 if OR0_CSCT_8_CYCLE + +config OR0_CST + hex + default 0x0 if !BR0_MACHINE_FCM + default 0x0 if OR0_CST_COINCIDENT + default 0x100 if OR0_CST_QUARTER_CLOCK + default 0x0 if OR0_CST_HALF_CLOCK + default 0x100 if OR0_CST_ONE_CLOCK + +config OR0_CHT + hex + default 0x0 if !BR0_MACHINE_FCM + default 0x0 if OR0_CHT_HALF_CLOCK + default 0x80 if OR0_CHT_ONE_CLOCK + default 0x0 if OR0_CHT_ONE_HALF_CLOCK + default 0x80 if OR0_CHT_TWO_CLOCK + +config OR0_RST + hex + default 0x0 if !BR0_MACHINE_FCM + default 0x0 if OR0_RST_THREE_QUARTER_CLOCK + default 0x8 if OR0_RST_ONE_CLOCK + default 0x0 if OR0_RST_ONE_HALF_CLOCK + +config OR0_CSNT + hex + default 0x0 if !BR0_MACHINE_GPCM + default 0x0 if OR0_CSNT_NORMAL + default 0x800 if OR0_CSNT_EARLIER + +config OR0_ACS + hex + default 0x0 if !BR0_MACHINE_GPCM + default 0x0 if OR0_ACS_SAME_TIME + default 0x400 if OR0_ACS_QUARTER_CYCLE_EARLIER + default 0x600 if OR0_ACS_HALF_CYCLE_EARLIER + +config OR0_XACS + hex + default 0x0 if !BR0_MACHINE_GPCM + default 0x0 if OR0_XACS_NORMAL + default 0x100 if OR0_XACS_EXTENDED + +config OR0_SETA + hex + default 0x0 if !BR0_MACHINE_GPCM + default 0x0 if OR0_SETA_INTERNAL + default 0x8 if OR0_SETA_EXTERNAL + +config OR0_TRLX + hex + default 0x0 if OR0_TRLX_NORMAL + default 0x4 if OR0_TRLX_RELAXED + +config OR0_EHTR + hex + default 0x0 if OR0_EHTR_NORMAL + default 0x2 if OR0_EHTR_1_CYCLE + default 0x0 if OR0_EHTR_4_CYCLE + default 0x2 if OR0_EHTR_8_CYCLE + +config OR0_EAD + hex + default 0x0 if ARCH_MPC8308 + default 0x0 if OR0_EAD_NONE + default 0x1 if OR0_EAD_EXTRA diff --git a/arch/powerpc/cpu/mpc83xx/elbc/Kconfig.elbc1 b/arch/powerpc/cpu/mpc83xx/elbc/Kconfig.elbc1 new file mode 100644 index 0000000000..08dcc7dd2b --- /dev/null +++ b/arch/powerpc/cpu/mpc83xx/elbc/Kconfig.elbc1 @@ -0,0 +1,733 @@ +menuconfig ELBC_BR1_OR1 + bool "ELBC BR1/OR1" + +if ELBC_BR1_OR1 + +config BR1_OR1_NAME + string "Identifier" + +config BR1_OR1_BASE + hex "Port base" + +choice + prompt "Port size" + +config BR1_PORTSIZE_8BIT + bool "8-bit" + +config BR1_PORTSIZE_16BIT + depends on !BR1_MACHINE_FCM + bool "16-bit" + + +config BR1_PORTSIZE_32BIT + depends on !BR1_MACHINE_FCM + depends on ARCH_MPC8349 || ARCH_MPC8360 || ARCH_MPC8379 + bool "32-bit" + +endchoice + +if BR1_MACHINE_FCM + +choice + prompt "Data Error Checking" + +config BR1_ERRORCHECKING_DISABLED + bool "Disabled" + +config BR1_ERRORCHECKING_ECC_CHECKING + bool "ECC checking / No ECC generation" + +config BR1_ERRORCHECKING_BOTH + bool "ECC checking and generation" + +endchoice + +endif + +config BR1_WRITE_PROTECT + bool "Write-protect" + +config BR1_MACHINE_UPM + bool + +choice + prompt "Machine select" + +config BR1_MACHINE_GPCM + bool "GPCM" + +config BR1_MACHINE_FCM + depends on !ARCH_MPC832X && !ARCH_MPC8349 && !ARCH_MPC8360 + bool "FCM" + +config BR1_MACHINE_SDRAM + depends on ARCH_MPC8349 || ARCH_MPC8360 + bool "SDRAM" + +config BR1_MACHINE_UPMA + select BR1_MACHINE_UPM + bool "UPM (A)" + +config BR1_MACHINE_UPMB + select BR1_MACHINE_UPM + bool "UPM (B)" + +config BR1_MACHINE_UPMC + select BR1_MACHINE_UPM + bool "UPM (C)" + +endchoice + +if ARCH_MPC8313 || ARCH_MPC8323 || ARCH_MPC8360 + +choice + prompt "Atomic operations" + +config BR1_ATOMIC_NONE + bool "No atomic operations" + +config BR1_ATOMIC_RAWA + bool "Read-after-write-atomic" + +config BR1_ATOMIC_WARA + bool "Write-after-read-atomic" + +endchoice + +endif + +if BR1_MACHINE_GPCM || BR1_MACHINE_FCM || BR1_MACHINE_UPM || BR1_MACHINE_SDRAM + +choice + prompt "Address mask" + +config OR1_AM_32_KBYTES + depends on !BR1_MACHINE_SDRAM + bool "32 kb" + +config OR1_AM_64_KBYTES + bool "64 kb" + +config OR1_AM_128_KBYTES + bool "128 kb" + +config OR1_AM_256_KBYTES + bool "256 kb" + +config OR1_AM_512_KBYTES + bool "512 kb" + +config OR1_AM_1_MBYTES + bool "1 mb" + +config OR1_AM_2_MBYTES + bool "2 mb" + +config OR1_AM_4_MBYTES + bool "4 mb" + +config OR1_AM_8_MBYTES + bool "8 mb" + +config OR1_AM_16_MBYTES + bool "16 mb" + +config OR1_AM_32_MBYTES + bool "32 mb" + +config OR1_AM_64_MBYTES + bool "64 mb" + +# XXX: Some boards define 128MB AM with GPCM, even though it should not be +# possible according to the manuals +config OR1_AM_128_MBYTES + bool "128 mb" + +# XXX: Some boards define 256MB AM with GPCM, even though it should not be +# possible according to the manuals +config OR1_AM_256_MBYTES + bool "256 mb" + +config OR1_AM_512_MBYTES + depends on BR1_MACHINE_FCM + bool "512 mb" + +# XXX: Some boards define 1GB AM with GPCM, even though it should not be +# possible according to the manuals +config OR1_AM_1_GBYTES + bool "1 gb" + +config OR1_AM_2_GBYTES + depends on BR1_MACHINE_FCM + bool "2 gb" + +config OR1_AM_4_GBYTES + depends on BR1_MACHINE_FCM + bool "4 gb" + +endchoice + +config OR1_XAM_SET + bool "Set unused bytes after address mask" +choice + prompt "Buffer control disable" + +config OR1_BCTLD_ASSERTED + bool "Asserted" + +config OR1_BCTLD_NOT_ASSERTED + bool "Not asserted" + +endchoice + +endif + +if BR1_MACHINE_GPCM || BR1_MACHINE_FCM + +choice + prompt "Cycle length in bus clocks" + +config OR1_SCY_0 + bool "No wait states" + +config OR1_SCY_1 + bool "1 wait state" + +config OR1_SCY_2 + bool "2 wait states" + +config OR1_SCY_3 + bool "3 wait states" + +config OR1_SCY_4 + bool "4 wait states" + +config OR1_SCY_5 + bool "5 wait states" + +config OR1_SCY_6 + bool "6 wait states" + +config OR1_SCY_7 + bool "7 wait states" + +config OR1_SCY_8 + depends on BR1_MACHINE_GPCM + bool "8 wait states" + +config OR1_SCY_9 + depends on BR1_MACHINE_GPCM + bool "9 wait states" + +config OR1_SCY_10 + depends on BR1_MACHINE_GPCM + bool "10 wait states" + +config OR1_SCY_11 + depends on BR1_MACHINE_GPCM + bool "11 wait states" + +config OR1_SCY_12 + depends on BR1_MACHINE_GPCM + bool "12 wait states" + +config OR1_SCY_13 + depends on BR1_MACHINE_GPCM + bool "13 wait states" + +config OR1_SCY_14 + depends on BR1_MACHINE_GPCM + bool "14 wait states" + +config OR1_SCY_15 + depends on BR1_MACHINE_GPCM + bool "15 wait states" + +endchoice + +endif # BR1_MACHINE_GPCM || BR1_MACHINE_FCM + +if BR1_MACHINE_GPCM + +choice + prompt "Chip select negotiation time" + +config OR1_CSNT_NORMAL + bool "Normal" + +config OR1_CSNT_EARLIER + bool "Earlier" + +endchoice + +choice + prompt "Address to chip-select setup" + +config OR1_ACS_SAME_TIME + bool "At the same time" + +config OR1_ACS_HALF_CYCLE_EARLIER + bool "Half of a bus clock cycle earlier" + +config OR1_ACS_QUARTER_CYCLE_EARLIER + bool "Half/Quarter of a bus clock cycle earlier" + +endchoice + +choice + prompt "Extra address to check-select setup" + +config OR1_XACS_NORMAL + bool "Normal" + +config OR1_XACS_EXTENDED + bool "Extended" + +endchoice + +choice + prompt "External address termination" + +config OR1_SETA_INTERNAL + bool "Access is terminated internally" + +config OR1_SETA_EXTERNAL + bool "Access is terminated externally" + +endchoice + +endif # BR1_MACHINE_GPCM + +if BR1_MACHINE_FCM + +choice + prompt "NAND Flash EEPROM page size" + +config OR1_PGS_SMALL + bool "Small page device" + +config OR1_PGS_LARGE + bool "Large page device" + +endchoice + +choice + prompt "Chip select to command time" + +config OR1_CSCT_1_CYCLE + depends on OR1_TRLX_NORMAL + bool "1 cycle" + +config OR1_CSCT_2_CYCLE + depends on OR1_TRLX_RELAXED + bool "2 cycles" + +config OR1_CSCT_4_CYCLE + depends on OR1_TRLX_NORMAL + bool "4 cycles" + +config OR1_CSCT_8_CYCLE + depends on OR1_TRLX_RELAXED + bool "8 cycles" + +endchoice + +choice + prompt "Command setup time" + +config OR1_CST_COINCIDENT + depends on OR1_TRLX_NORMAL + bool "Coincident with any command" + +config OR1_CST_QUARTER_CLOCK + depends on OR1_TRLX_NORMAL + bool "0.25 clocks after" + +config OR1_CST_HALF_CLOCK + depends on OR1_TRLX_RELAXED + bool "0.5 clocks after" + +config OR1_CST_ONE_CLOCK + depends on OR1_TRLX_RELAXED + bool "1 clock after" + +endchoice + +choice + prompt "Command hold time" + +config OR1_CHT_HALF_CLOCK + depends on OR1_TRLX_NORMAL + bool "0.5 clocks before" + +config OR1_CHT_ONE_CLOCK + depends on OR1_TRLX_NORMAL + bool "1 clock before" + +config OR1_CHT_ONE_HALF_CLOCK + depends on OR1_TRLX_RELAXED + bool "1.5 clocks before" + +config OR1_CHT_TWO_CLOCK + depends on OR1_TRLX_RELAXED + bool "2 clocks before" + +endchoice + +choice + prompt "Reset setup time" + +config OR1_RST_THREE_QUARTER_CLOCK + depends on OR1_TRLX_NORMAL + bool "0.75 clocks prior" + +config OR1_RST_ONE_HALF_CLOCK + depends on OR1_TRLX_RELAXED + bool "0.5 clocks prior" + +config OR1_RST_ONE_CLOCK + bool "1 clock prior" + +endchoice + +endif # BR1_MACHINE_FCM + +if BR1_MACHINE_UPM + +choice + prompt "Burst inhibit" + +config OR1_BI_BURSTSUPPORT + bool "Support burst access" + +config OR1_BI_BURSTINHIBIT + bool "Inhibit burst access" + +endchoice + +endif # BR1_MACHINE_UPM + +if BR1_MACHINE_SDRAM + +choice + prompt "Number of column address lines" + +config OR1_COLS_7 + bool "7" + +config OR1_COLS_8 + bool "8" + +config OR1_COLS_9 + bool "9" + +config OR1_COLS_10 + bool "10" + +config OR1_COLS_11 + bool "11" + +config OR1_COLS_12 + bool "12" + +config OR1_COLS_13 + bool "13" + +config OR1_COLS_14 + bool "14" + +endchoice + +choice + prompt "Number of rows address lines" + +config OR1_ROWS_9 + bool "9" + +config OR1_ROWS_10 + bool "10" + +config OR1_ROWS_11 + bool "11" + +config OR1_ROWS_12 + bool "12" + +config OR1_ROWS_13 + bool "13" + +config OR1_ROWS_14 + bool "14" + +config OR1_ROWS_15 + bool "15" + +endchoice + +choice + prompt "Page mode select" + +config OR1_PMSEL_BTB + bool "Back-to-back" + +config OR1_PMSEL_KEPT_OPEN + bool "Page kept open until page miss or refresh" + +endchoice + +endif # BR1_MACHINE_SDRAM + +choice + prompt "Relaxed timing" + +config OR1_TRLX_NORMAL + bool "Normal" + +config OR1_TRLX_RELAXED + bool "Relaxed" + +endchoice + +choice + prompt "Extended hold time" + +config OR1_EHTR_NORMAL + depends on OR1_TRLX_NORMAL + bool "Normal" + +config OR1_EHTR_1_CYCLE + depends on OR1_TRLX_NORMAL + bool "1 idle clock cycle inserted" + +config OR1_EHTR_4_CYCLE + depends on OR1_TRLX_RELAXED + bool "4 idle clock cycles inserted" + +config OR1_EHTR_8_CYCLE + depends on OR1_TRLX_RELAXED + bool "8 idle clock cycles inserted" + +endchoice + +if !ARCH_MPC8308 + +choice + prompt "External address latch delay" + +config OR1_EAD_NONE + bool "None" + +config OR1_EAD_EXTRA + bool "Extra" + +endchoice + +endif # !ARCH_MPC8308 + +endif # ELBC_BR1_OR1 + +config BR1_PORTSIZE + hex + default 0x800 if BR1_PORTSIZE_8BIT + default 0x1000 if BR1_PORTSIZE_16BIT + default 0x1800 if BR1_PORTSIZE_32BIT + +config BR1_ERRORCHECKING + hex + default 0x0 if !BR1_MACHINE_FCM + default 0x0 if BR1_ERRORCHECKING_DISABLED + default 0x200 if BR1_ERRORCHECKING_ECC_CHECKING + default 0x400 if BR1_ERRORCHECKING_BOTH + +config BR1_WRITE_PROTECT_BIT + hex + default 0x0 if !BR1_WRITE_PROTECT + default 0x100 if BR1_WRITE_PROTECT + +config BR1_MACHINE + hex + default 0x0 if BR1_MACHINE_GPCM + default 0x20 if BR1_MACHINE_FCM + default 0x60 if BR1_MACHINE_SDRAM + default 0x80 if BR1_MACHINE_UPMA + default 0xa0 if BR1_MACHINE_UPMB + default 0xc0 if BR1_MACHINE_UPMC + +config BR1_ATOMIC + hex + default 0x0 if !ARCH_MPC8313 && !ARCH_MPC8323 && !ARCH_MPC8360 + default 0x0 if BR1_ATOMIC_NONE + default 0x4 if BR1_ATOMIC_RAWA + default 0x8 if BR1_ATOMIC_WARA + +config BR1_VALID_BIT + hex + default 0x0 if !ELBC_BR1_OR1 + default 0x1 if ELBC_BR1_OR1 + +config OR1_AM + hex + default 0xffff8000 if OR1_AM_32_KBYTES && !BR1_MACHINE_SDRAM + default 0xffff0000 if OR1_AM_64_KBYTES + default 0xfffe0000 if OR1_AM_128_KBYTES + default 0xfffc0000 if OR1_AM_256_KBYTES + default 0xfff80000 if OR1_AM_512_KBYTES + default 0xfff00000 if OR1_AM_1_MBYTES + default 0xffe00000 if OR1_AM_2_MBYTES + default 0xffc00000 if OR1_AM_4_MBYTES + default 0xff800000 if OR1_AM_8_MBYTES + default 0xff000000 if OR1_AM_16_MBYTES + default 0xfe000000 if OR1_AM_32_MBYTES + default 0xfc000000 if OR1_AM_64_MBYTES + default 0xf8000000 if OR1_AM_128_MBYTES + default 0xf0000000 if OR1_AM_256_MBYTES + default 0xe0000000 if OR1_AM_512_MBYTES + default 0xc0000000 if OR1_AM_1_GBYTES + default 0x80000000 if OR1_AM_2_GBYTES + default 0x00000000 if OR1_AM_4_GBYTES + +config OR1_XAM + hex + default 0x0 if !OR1_XAM_SET + default 0x6000 if OR1_XAM_SET + +config OR1_BCTLD + hex + default 0x0 if OR1_BCTLD_ASSERTED + default 0x1000 if OR1_BCTLD_NOT_ASSERTED + +config OR1_BI + hex + default 0x0 if !BR1_MACHINE_UPM + default 0x0 if OR1_BI_BURSTSUPPORT + default 0x100 if OR1_BI_BURSTINHIBIT + +config OR1_COLS + hex + default 0x0 if !BR1_MACHINE_SDRAM + default 0x0 if OR1_COLS_7 + default 0x400 if OR1_COLS_8 + default 0x800 if OR1_COLS_9 + default 0xc00 if OR1_COLS_10 + default 0x1000 if OR1_COLS_11 + default 0x1400 if OR1_COLS_12 + default 0x1800 if OR1_COLS_13 + default 0x1c00 if OR1_COLS_14 + +config OR1_ROWS + hex + default 0x0 if !BR1_MACHINE_SDRAM + default 0x0 if OR1_ROWS_9 + default 0x40 if OR1_ROWS_10 + default 0x80 if OR1_ROWS_11 + default 0xc0 if OR1_ROWS_12 + default 0x100 if OR1_ROWS_13 + default 0x140 if OR1_ROWS_14 + default 0x180 if OR1_ROWS_15 + +config OR1_PMSEL + hex + default 0x0 if !BR1_MACHINE_SDRAM + default 0x0 if OR1_PMSEL_BTB + default 0x20 if OR1_PMSEL_KEPT_OPEN + +config OR1_SCY + hex + default 0x0 if !BR1_MACHINE_GPCM && !BR1_MACHINE_FCM + default 0x0 if OR1_SCY_0 + default 0x10 if OR1_SCY_1 + default 0x20 if OR1_SCY_2 + default 0x30 if OR1_SCY_3 + default 0x40 if OR1_SCY_4 + default 0x50 if OR1_SCY_5 + default 0x60 if OR1_SCY_6 + default 0x70 if OR1_SCY_7 + default 0x80 if OR1_SCY_8 + default 0x90 if OR1_SCY_9 + default 0xa0 if OR1_SCY_10 + default 0xb0 if OR1_SCY_11 + default 0xc0 if OR1_SCY_12 + default 0xd0 if OR1_SCY_13 + default 0xe0 if OR1_SCY_14 + default 0xf0 if OR1_SCY_15 + +config OR1_PGS + hex + default 0x0 if !BR1_MACHINE_FCM + default 0x0 if OR1_PGS_SMALL + default 0x400 if OR1_PGS_LARGE + +config OR1_CSCT + hex + default 0x0 if !BR1_MACHINE_FCM + default 0x0 if OR1_CSCT_1_CYCLE + default 0x0 if OR1_CSCT_2_CYCLE + default 0x200 if OR1_CSCT_4_CYCLE + default 0x200 if OR1_CSCT_8_CYCLE + +config OR1_CST + hex + default 0x0 if !BR1_MACHINE_FCM + default 0x0 if OR1_CST_COINCIDENT + default 0x100 if OR1_CST_QUARTER_CLOCK + default 0x0 if OR1_CST_HALF_CLOCK + default 0x100 if OR1_CST_ONE_CLOCK + +config OR1_CHT + hex + default 0x0 if !BR1_MACHINE_FCM + default 0x0 if OR1_CHT_HALF_CLOCK + default 0x80 if OR1_CHT_ONE_CLOCK + default 0x0 if OR1_CHT_ONE_HALF_CLOCK + default 0x80 if OR1_CHT_TWO_CLOCK + +config OR1_RST + hex + default 0x0 if !BR1_MACHINE_FCM + default 0x0 if OR1_RST_THREE_QUARTER_CLOCK + default 0x8 if OR1_RST_ONE_CLOCK + default 0x0 if OR1_RST_ONE_HALF_CLOCK + +config OR1_CSNT + hex + default 0x0 if !BR1_MACHINE_GPCM + default 0x0 if OR1_CSNT_NORMAL + default 0x800 if OR1_CSNT_EARLIER + +config OR1_ACS + hex + default 0x0 if !BR1_MACHINE_GPCM + default 0x0 if OR1_ACS_SAME_TIME + default 0x400 if OR1_ACS_QUARTER_CYCLE_EARLIER + default 0x600 if OR1_ACS_HALF_CYCLE_EARLIER + +config OR1_XACS + hex + default 0x0 if !BR1_MACHINE_GPCM + default 0x0 if OR1_XACS_NORMAL + default 0x100 if OR1_XACS_EXTENDED + +config OR1_SETA + hex + default 0x0 if !BR1_MACHINE_GPCM + default 0x0 if OR1_SETA_INTERNAL + default 0x8 if OR1_SETA_EXTERNAL + +config OR1_TRLX + hex + default 0x0 if OR1_TRLX_NORMAL + default 0x4 if OR1_TRLX_RELAXED + +config OR1_EHTR + hex + default 0x0 if OR1_EHTR_NORMAL + default 0x2 if OR1_EHTR_1_CYCLE + default 0x0 if OR1_EHTR_4_CYCLE + default 0x2 if OR1_EHTR_8_CYCLE + +config OR1_EAD + hex + default 0x0 if ARCH_MPC8308 + default 0x0 if OR1_EAD_NONE + default 0x1 if OR1_EAD_EXTRA diff --git a/arch/powerpc/cpu/mpc83xx/elbc/Kconfig.elbc2 b/arch/powerpc/cpu/mpc83xx/elbc/Kconfig.elbc2 new file mode 100644 index 0000000000..298d87f5e0 --- /dev/null +++ b/arch/powerpc/cpu/mpc83xx/elbc/Kconfig.elbc2 @@ -0,0 +1,733 @@ +menuconfig ELBC_BR2_OR2 + bool "ELBC BR2/OR2" + +if ELBC_BR2_OR2 + +config BR2_OR2_NAME + string "Identifier" + +config BR2_OR2_BASE + hex "Port base" + +choice + prompt "Port size" + +config BR2_PORTSIZE_8BIT + bool "8-bit" + +config BR2_PORTSIZE_16BIT + depends on !BR2_MACHINE_FCM + bool "16-bit" + + +config BR2_PORTSIZE_32BIT + depends on !BR2_MACHINE_FCM + depends on ARCH_MPC8349 || ARCH_MPC8360 || ARCH_MPC8379 + bool "32-bit" + +endchoice + +if BR2_MACHINE_FCM + +choice + prompt "Data Error Checking" + +config BR2_ERRORCHECKING_DISABLED + bool "Disabled" + +config BR2_ERRORCHECKING_ECC_CHECKING + bool "ECC checking / No ECC generation" + +config BR2_ERRORCHECKING_BOTH + bool "ECC checking and generation" + +endchoice + +endif + +config BR2_WRITE_PROTECT + bool "Write-protect" + +config BR2_MACHINE_UPM + bool + +choice + prompt "Machine select" + +config BR2_MACHINE_GPCM + bool "GPCM" + +config BR2_MACHINE_FCM + depends on !ARCH_MPC832X && !ARCH_MPC8349 && !ARCH_MPC8360 + bool "FCM" + +config BR2_MACHINE_SDRAM + depends on ARCH_MPC8349 || ARCH_MPC8360 + bool "SDRAM" + +config BR2_MACHINE_UPMA + select BR2_MACHINE_UPM + bool "UPM (A)" + +config BR2_MACHINE_UPMB + select BR2_MACHINE_UPM + bool "UPM (B)" + +config BR2_MACHINE_UPMC + select BR2_MACHINE_UPM + bool "UPM (C)" + +endchoice + +if ARCH_MPC8313 || ARCH_MPC8323 || ARCH_MPC8360 + +choice + prompt "Atomic operations" + +config BR2_ATOMIC_NONE + bool "No atomic operations" + +config BR2_ATOMIC_RAWA + bool "Read-after-write-atomic" + +config BR2_ATOMIC_WARA + bool "Write-after-read-atomic" + +endchoice + +endif + +if BR2_MACHINE_GPCM || BR2_MACHINE_FCM || BR2_MACHINE_UPM || BR2_MACHINE_SDRAM + +choice + prompt "Address mask" + +config OR2_AM_32_KBYTES + depends on !BR2_MACHINE_SDRAM + bool "32 kb" + +config OR2_AM_64_KBYTES + bool "64 kb" + +config OR2_AM_128_KBYTES + bool "128 kb" + +config OR2_AM_256_KBYTES + bool "256 kb" + +config OR2_AM_512_KBYTES + bool "512 kb" + +config OR2_AM_1_MBYTES + bool "1 mb" + +config OR2_AM_2_MBYTES + bool "2 mb" + +config OR2_AM_4_MBYTES + bool "4 mb" + +config OR2_AM_8_MBYTES + bool "8 mb" + +config OR2_AM_16_MBYTES + bool "16 mb" + +config OR2_AM_32_MBYTES + bool "32 mb" + +config OR2_AM_64_MBYTES + bool "64 mb" + +# XXX: Some boards define 128MB AM with GPCM, even though it should not be +# possible according to the manuals +config OR2_AM_128_MBYTES + bool "128 mb" + +# XXX: Some boards define 256MB AM with GPCM, even though it should not be +# possible according to the manuals +config OR2_AM_256_MBYTES + bool "256 mb" + +config OR2_AM_512_MBYTES + depends on BR2_MACHINE_FCM + bool "512 mb" + +# XXX: Some boards define 1GB AM with GPCM, even though it should not be +# possible according to the manuals +config OR2_AM_1_GBYTES + bool "1 gb" + +config OR2_AM_2_GBYTES + depends on BR2_MACHINE_FCM + bool "2 gb" + +config OR2_AM_4_GBYTES + depends on BR2_MACHINE_FCM + bool "4 gb" + +endchoice + +config OR2_XAM_SET + bool "Set unused bytes after address mask" +choice + prompt "Buffer control disable" + +config OR2_BCTLD_ASSERTED + bool "Asserted" + +config OR2_BCTLD_NOT_ASSERTED + bool "Not asserted" + +endchoice + +endif + +if BR2_MACHINE_GPCM || BR2_MACHINE_FCM + +choice + prompt "Cycle length in bus clocks" + +config OR2_SCY_0 + bool "No wait states" + +config OR2_SCY_1 + bool "1 wait state" + +config OR2_SCY_2 + bool "2 wait states" + +config OR2_SCY_3 + bool "3 wait states" + +config OR2_SCY_4 + bool "4 wait states" + +config OR2_SCY_5 + bool "5 wait states" + +config OR2_SCY_6 + bool "6 wait states" + +config OR2_SCY_7 + bool "7 wait states" + +config OR2_SCY_8 + depends on BR2_MACHINE_GPCM + bool "8 wait states" + +config OR2_SCY_9 + depends on BR2_MACHINE_GPCM + bool "9 wait states" + +config OR2_SCY_10 + depends on BR2_MACHINE_GPCM + bool "10 wait states" + +config OR2_SCY_11 + depends on BR2_MACHINE_GPCM + bool "11 wait states" + +config OR2_SCY_12 + depends on BR2_MACHINE_GPCM + bool "12 wait states" + +config OR2_SCY_13 + depends on BR2_MACHINE_GPCM + bool "13 wait states" + +config OR2_SCY_14 + depends on BR2_MACHINE_GPCM + bool "14 wait states" + +config OR2_SCY_15 + depends on BR2_MACHINE_GPCM + bool "15 wait states" + +endchoice + +endif # BR2_MACHINE_GPCM || BR2_MACHINE_FCM + +if BR2_MACHINE_GPCM + +choice + prompt "Chip select negotiation time" + +config OR2_CSNT_NORMAL + bool "Normal" + +config OR2_CSNT_EARLIER + bool "Earlier" + +endchoice + +choice + prompt "Address to chip-select setup" + +config OR2_ACS_SAME_TIME + bool "At the same time" + +config OR2_ACS_HALF_CYCLE_EARLIER + bool "Half of a bus clock cycle earlier" + +config OR2_ACS_QUARTER_CYCLE_EARLIER + bool "Half/Quarter of a bus clock cycle earlier" + +endchoice + +choice + prompt "Extra address to check-select setup" + +config OR2_XACS_NORMAL + bool "Normal" + +config OR2_XACS_EXTENDED + bool "Extended" + +endchoice + +choice + prompt "External address termination" + +config OR2_SETA_INTERNAL + bool "Access is terminated internally" + +config OR2_SETA_EXTERNAL + bool "Access is terminated externally" + +endchoice + +endif # BR2_MACHINE_GPCM + +if BR2_MACHINE_FCM + +choice + prompt "NAND Flash EEPROM page size" + +config OR2_PGS_SMALL + bool "Small page device" + +config OR2_PGS_LARGE + bool "Large page device" + +endchoice + +choice + prompt "Chip select to command time" + +config OR2_CSCT_1_CYCLE + depends on OR2_TRLX_NORMAL + bool "1 cycle" + +config OR2_CSCT_2_CYCLE + depends on OR2_TRLX_RELAXED + bool "2 cycles" + +config OR2_CSCT_4_CYCLE + depends on OR2_TRLX_NORMAL + bool "4 cycles" + +config OR2_CSCT_8_CYCLE + depends on OR2_TRLX_RELAXED + bool "8 cycles" + +endchoice + +choice + prompt "Command setup time" + +config OR2_CST_COINCIDENT + depends on OR2_TRLX_NORMAL + bool "Coincident with any command" + +config OR2_CST_QUARTER_CLOCK + depends on OR2_TRLX_NORMAL + bool "0.25 clocks after" + +config OR2_CST_HALF_CLOCK + depends on OR2_TRLX_RELAXED + bool "0.5 clocks after" + +config OR2_CST_ONE_CLOCK + depends on OR2_TRLX_RELAXED + bool "1 clock after" + +endchoice + +choice + prompt "Command hold time" + +config OR2_CHT_HALF_CLOCK + depends on OR2_TRLX_NORMAL + bool "0.5 clocks before" + +config OR2_CHT_ONE_CLOCK + depends on OR2_TRLX_NORMAL + bool "1 clock before" + +config OR2_CHT_ONE_HALF_CLOCK + depends on OR2_TRLX_RELAXED + bool "1.5 clocks before" + +config OR2_CHT_TWO_CLOCK + depends on OR2_TRLX_RELAXED + bool "2 clocks before" + +endchoice + +choice + prompt "Reset setup time" + +config OR2_RST_THREE_QUARTER_CLOCK + depends on OR2_TRLX_NORMAL + bool "0.75 clocks prior" + +config OR2_RST_ONE_HALF_CLOCK + depends on OR2_TRLX_RELAXED + bool "0.5 clocks prior" + +config OR2_RST_ONE_CLOCK + bool "1 clock prior" + +endchoice + +endif # BR2_MACHINE_FCM + +if BR2_MACHINE_UPM + +choice + prompt "Burst inhibit" + +config OR2_BI_BURSTSUPPORT + bool "Support burst access" + +config OR2_BI_BURSTINHIBIT + bool "Inhibit burst access" + +endchoice + +endif # BR2_MACHINE_UPM + +if BR2_MACHINE_SDRAM + +choice + prompt "Number of column address lines" + +config OR2_COLS_7 + bool "7" + +config OR2_COLS_8 + bool "8" + +config OR2_COLS_9 + bool "9" + +config OR2_COLS_10 + bool "10" + +config OR2_COLS_11 + bool "11" + +config OR2_COLS_12 + bool "12" + +config OR2_COLS_13 + bool "13" + +config OR2_COLS_14 + bool "14" + +endchoice + +choice + prompt "Number of rows address lines" + +config OR2_ROWS_9 + bool "9" + +config OR2_ROWS_10 + bool "10" + +config OR2_ROWS_11 + bool "11" + +config OR2_ROWS_12 + bool "12" + +config OR2_ROWS_13 + bool "13" + +config OR2_ROWS_14 + bool "14" + +config OR2_ROWS_15 + bool "15" + +endchoice + +choice + prompt "Page mode select" + +config OR2_PMSEL_BTB + bool "Back-to-back" + +config OR2_PMSEL_KEPT_OPEN + bool "Page kept open until page miss or refresh" + +endchoice + +endif # BR2_MACHINE_SDRAM + +choice + prompt "Relaxed timing" + +config OR2_TRLX_NORMAL + bool "Normal" + +config OR2_TRLX_RELAXED + bool "Relaxed" + +endchoice + +choice + prompt "Extended hold time" + +config OR2_EHTR_NORMAL + depends on OR2_TRLX_NORMAL + bool "Normal" + +config OR2_EHTR_1_CYCLE + depends on OR2_TRLX_NORMAL + bool "1 idle clock cycle inserted" + +config OR2_EHTR_4_CYCLE + depends on OR2_TRLX_RELAXED + bool "4 idle clock cycles inserted" + +config OR2_EHTR_8_CYCLE + depends on OR2_TRLX_RELAXED + bool "8 idle clock cycles inserted" + +endchoice + +if !ARCH_MPC8308 + +choice + prompt "External address latch delay" + +config OR2_EAD_NONE + bool "None" + +config OR2_EAD_EXTRA + bool "Extra" + +endchoice + +endif # !ARCH_MPC8308 + +endif # ELBC_BR2_OR2 + +config BR2_PORTSIZE + hex + default 0x800 if BR2_PORTSIZE_8BIT + default 0x1000 if BR2_PORTSIZE_16BIT + default 0x1800 if BR2_PORTSIZE_32BIT + +config BR2_ERRORCHECKING + hex + default 0x0 if !BR2_MACHINE_FCM + default 0x0 if BR2_ERRORCHECKING_DISABLED + default 0x200 if BR2_ERRORCHECKING_ECC_CHECKING + default 0x400 if BR2_ERRORCHECKING_BOTH + +config BR2_WRITE_PROTECT_BIT + hex + default 0x0 if !BR2_WRITE_PROTECT + default 0x100 if BR2_WRITE_PROTECT + +config BR2_MACHINE + hex + default 0x0 if BR2_MACHINE_GPCM + default 0x20 if BR2_MACHINE_FCM + default 0x60 if BR2_MACHINE_SDRAM + default 0x80 if BR2_MACHINE_UPMA + default 0xa0 if BR2_MACHINE_UPMB + default 0xc0 if BR2_MACHINE_UPMC + +config BR2_ATOMIC + hex + default 0x0 if !ARCH_MPC8313 && !ARCH_MPC8323 && !ARCH_MPC8360 + default 0x0 if BR2_ATOMIC_NONE + default 0x4 if BR2_ATOMIC_RAWA + default 0x8 if BR2_ATOMIC_WARA + +config BR2_VALID_BIT + hex + default 0x0 if !ELBC_BR2_OR2 + default 0x1 if ELBC_BR2_OR2 + +config OR2_AM + hex + default 0xffff8000 if OR2_AM_32_KBYTES && !BR2_MACHINE_SDRAM + default 0xffff0000 if OR2_AM_64_KBYTES + default 0xfffe0000 if OR2_AM_128_KBYTES + default 0xfffc0000 if OR2_AM_256_KBYTES + default 0xfff80000 if OR2_AM_512_KBYTES + default 0xfff00000 if OR2_AM_1_MBYTES + default 0xffe00000 if OR2_AM_2_MBYTES + default 0xffc00000 if OR2_AM_4_MBYTES + default 0xff800000 if OR2_AM_8_MBYTES + default 0xff000000 if OR2_AM_16_MBYTES + default 0xfe000000 if OR2_AM_32_MBYTES + default 0xfc000000 if OR2_AM_64_MBYTES + default 0xf8000000 if OR2_AM_128_MBYTES + default 0xf0000000 if OR2_AM_256_MBYTES + default 0xe0000000 if OR2_AM_512_MBYTES + default 0xc0000000 if OR2_AM_1_GBYTES + default 0x80000000 if OR2_AM_2_GBYTES + default 0x00000000 if OR2_AM_4_GBYTES + +config OR2_XAM + hex + default 0x0 if !OR2_XAM_SET + default 0x6000 if OR2_XAM_SET + +config OR2_BCTLD + hex + default 0x0 if OR2_BCTLD_ASSERTED + default 0x1000 if OR2_BCTLD_NOT_ASSERTED + +config OR2_BI + hex + default 0x0 if !BR2_MACHINE_UPM + default 0x0 if OR2_BI_BURSTSUPPORT + default 0x100 if OR2_BI_BURSTINHIBIT + +config OR2_COLS + hex + default 0x0 if !BR2_MACHINE_SDRAM + default 0x0 if OR2_COLS_7 + default 0x400 if OR2_COLS_8 + default 0x800 if OR2_COLS_9 + default 0xc00 if OR2_COLS_10 + default 0x1000 if OR2_COLS_11 + default 0x1400 if OR2_COLS_12 + default 0x1800 if OR2_COLS_13 + default 0x1c00 if OR2_COLS_14 + +config OR2_ROWS + hex + default 0x0 if !BR2_MACHINE_SDRAM + default 0x0 if OR2_ROWS_9 + default 0x40 if OR2_ROWS_10 + default 0x80 if OR2_ROWS_11 + default 0xc0 if OR2_ROWS_12 + default 0x100 if OR2_ROWS_13 + default 0x140 if OR2_ROWS_14 + default 0x180 if OR2_ROWS_15 + +config OR2_PMSEL + hex + default 0x0 if !BR2_MACHINE_SDRAM + default 0x0 if OR2_PMSEL_BTB + default 0x20 if OR2_PMSEL_KEPT_OPEN + +config OR2_SCY + hex + default 0x0 if !BR2_MACHINE_GPCM && !BR2_MACHINE_FCM + default 0x0 if OR2_SCY_0 + default 0x10 if OR2_SCY_1 + default 0x20 if OR2_SCY_2 + default 0x30 if OR2_SCY_3 + default 0x40 if OR2_SCY_4 + default 0x50 if OR2_SCY_5 + default 0x60 if OR2_SCY_6 + default 0x70 if OR2_SCY_7 + default 0x80 if OR2_SCY_8 + default 0x90 if OR2_SCY_9 + default 0xa0 if OR2_SCY_10 + default 0xb0 if OR2_SCY_11 + default 0xc0 if OR2_SCY_12 + default 0xd0 if OR2_SCY_13 + default 0xe0 if OR2_SCY_14 + default 0xf0 if OR2_SCY_15 + +config OR2_PGS + hex + default 0x0 if !BR2_MACHINE_FCM + default 0x0 if OR2_PGS_SMALL + default 0x400 if OR2_PGS_LARGE + +config OR2_CSCT + hex + default 0x0 if !BR2_MACHINE_FCM + default 0x0 if OR2_CSCT_1_CYCLE + default 0x0 if OR2_CSCT_2_CYCLE + default 0x200 if OR2_CSCT_4_CYCLE + default 0x200 if OR2_CSCT_8_CYCLE + +config OR2_CST + hex + default 0x0 if !BR2_MACHINE_FCM + default 0x0 if OR2_CST_COINCIDENT + default 0x100 if OR2_CST_QUARTER_CLOCK + default 0x0 if OR2_CST_HALF_CLOCK + default 0x100 if OR2_CST_ONE_CLOCK + +config OR2_CHT + hex + default 0x0 if !BR2_MACHINE_FCM + default 0x0 if OR2_CHT_HALF_CLOCK + default 0x80 if OR2_CHT_ONE_CLOCK + default 0x0 if OR2_CHT_ONE_HALF_CLOCK + default 0x80 if OR2_CHT_TWO_CLOCK + +config OR2_RST + hex + default 0x0 if !BR2_MACHINE_FCM + default 0x0 if OR2_RST_THREE_QUARTER_CLOCK + default 0x8 if OR2_RST_ONE_CLOCK + default 0x0 if OR2_RST_ONE_HALF_CLOCK + +config OR2_CSNT + hex + default 0x0 if !BR2_MACHINE_GPCM + default 0x0 if OR2_CSNT_NORMAL + default 0x800 if OR2_CSNT_EARLIER + +config OR2_ACS + hex + default 0x0 if !BR2_MACHINE_GPCM + default 0x0 if OR2_ACS_SAME_TIME + default 0x400 if OR2_ACS_QUARTER_CYCLE_EARLIER + default 0x600 if OR2_ACS_HALF_CYCLE_EARLIER + +config OR2_XACS + hex + default 0x0 if !BR2_MACHINE_GPCM + default 0x0 if OR2_XACS_NORMAL + default 0x100 if OR2_XACS_EXTENDED + +config OR2_SETA + hex + default 0x0 if !BR2_MACHINE_GPCM + default 0x0 if OR2_SETA_INTERNAL + default 0x8 if OR2_SETA_EXTERNAL + +config OR2_TRLX + hex + default 0x0 if OR2_TRLX_NORMAL + default 0x4 if OR2_TRLX_RELAXED + +config OR2_EHTR + hex + default 0x0 if OR2_EHTR_NORMAL + default 0x2 if OR2_EHTR_1_CYCLE + default 0x0 if OR2_EHTR_4_CYCLE + default 0x2 if OR2_EHTR_8_CYCLE + +config OR2_EAD + hex + default 0x0 if ARCH_MPC8308 + default 0x0 if OR2_EAD_NONE + default 0x1 if OR2_EAD_EXTRA diff --git a/arch/powerpc/cpu/mpc83xx/elbc/Kconfig.elbc3 b/arch/powerpc/cpu/mpc83xx/elbc/Kconfig.elbc3 new file mode 100644 index 0000000000..963831bfcb --- /dev/null +++ b/arch/powerpc/cpu/mpc83xx/elbc/Kconfig.elbc3 @@ -0,0 +1,733 @@ +menuconfig ELBC_BR3_OR3 + bool "ELBC BR3/OR3" + +if ELBC_BR3_OR3 + +config BR3_OR3_NAME + string "Identifier" + +config BR3_OR3_BASE + hex "Port base" + +choice + prompt "Port size" + +config BR3_PORTSIZE_8BIT + bool "8-bit" + +config BR3_PORTSIZE_16BIT + depends on !BR3_MACHINE_FCM + bool "16-bit" + + +config BR3_PORTSIZE_32BIT + depends on !BR3_MACHINE_FCM + depends on ARCH_MPC8349 || ARCH_MPC8360 || ARCH_MPC8379 + bool "32-bit" + +endchoice + +if BR3_MACHINE_FCM + +choice + prompt "Data Error Checking" + +config BR3_ERRORCHECKING_DISABLED + bool "Disabled" + +config BR3_ERRORCHECKING_ECC_CHECKING + bool "ECC checking / No ECC generation" + +config BR3_ERRORCHECKING_BOTH + bool "ECC checking and generation" + +endchoice + +endif + +config BR3_WRITE_PROTECT + bool "Write-protect" + +config BR3_MACHINE_UPM + bool + +choice + prompt "Machine select" + +config BR3_MACHINE_GPCM + bool "GPCM" + +config BR3_MACHINE_FCM + depends on !ARCH_MPC832X && !ARCH_MPC8349 && !ARCH_MPC8360 + bool "FCM" + +config BR3_MACHINE_SDRAM + depends on ARCH_MPC8349 || ARCH_MPC8360 + bool "SDRAM" + +config BR3_MACHINE_UPMA + select BR3_MACHINE_UPM + bool "UPM (A)" + +config BR3_MACHINE_UPMB + select BR3_MACHINE_UPM + bool "UPM (B)" + +config BR3_MACHINE_UPMC + select BR3_MACHINE_UPM + bool "UPM (C)" + +endchoice + +if ARCH_MPC8313 || ARCH_MPC8323 || ARCH_MPC8360 + +choice + prompt "Atomic operations" + +config BR3_ATOMIC_NONE + bool "No atomic operations" + +config BR3_ATOMIC_RAWA + bool "Read-after-write-atomic" + +config BR3_ATOMIC_WARA + bool "Write-after-read-atomic" + +endchoice + +endif + +if BR3_MACHINE_GPCM || BR3_MACHINE_FCM || BR3_MACHINE_UPM || BR3_MACHINE_SDRAM + +choice + prompt "Address mask" + +config OR3_AM_32_KBYTES + depends on !BR3_MACHINE_SDRAM + bool "32 kb" + +config OR3_AM_64_KBYTES + bool "64 kb" + +config OR3_AM_128_KBYTES + bool "128 kb" + +config OR3_AM_256_KBYTES + bool "256 kb" + +config OR3_AM_512_KBYTES + bool "512 kb" + +config OR3_AM_1_MBYTES + bool "1 mb" + +config OR3_AM_2_MBYTES + bool "2 mb" + +config OR3_AM_4_MBYTES + bool "4 mb" + +config OR3_AM_8_MBYTES + bool "8 mb" + +config OR3_AM_16_MBYTES + bool "16 mb" + +config OR3_AM_32_MBYTES + bool "32 mb" + +config OR3_AM_64_MBYTES + bool "64 mb" + +# XXX: Some boards define 128MB AM with GPCM, even though it should not be +# possible according to the manuals +config OR3_AM_128_MBYTES + bool "128 mb" + +# XXX: Some boards define 256MB AM with GPCM, even though it should not be +# possible according to the manuals +config OR3_AM_256_MBYTES + bool "256 mb" + +config OR3_AM_512_MBYTES + depends on BR3_MACHINE_FCM + bool "512 mb" + +# XXX: Some boards define 1GB AM with GPCM, even though it should not be +# possible according to the manuals +config OR3_AM_1_GBYTES + bool "1 gb" + +config OR3_AM_2_GBYTES + depends on BR3_MACHINE_FCM + bool "2 gb" + +config OR3_AM_4_GBYTES + depends on BR3_MACHINE_FCM + bool "4 gb" + +endchoice + +config OR3_XAM_SET + bool "Set unused bytes after address mask" +choice + prompt "Buffer control disable" + +config OR3_BCTLD_ASSERTED + bool "Asserted" + +config OR3_BCTLD_NOT_ASSERTED + bool "Not asserted" + +endchoice + +endif + +if BR3_MACHINE_GPCM || BR3_MACHINE_FCM + +choice + prompt "Cycle length in bus clocks" + +config OR3_SCY_0 + bool "No wait states" + +config OR3_SCY_1 + bool "1 wait state" + +config OR3_SCY_2 + bool "2 wait states" + +config OR3_SCY_3 + bool "3 wait states" + +config OR3_SCY_4 + bool "4 wait states" + +config OR3_SCY_5 + bool "5 wait states" + +config OR3_SCY_6 + bool "6 wait states" + +config OR3_SCY_7 + bool "7 wait states" + +config OR3_SCY_8 + depends on BR3_MACHINE_GPCM + bool "8 wait states" + +config OR3_SCY_9 + depends on BR3_MACHINE_GPCM + bool "9 wait states" + +config OR3_SCY_10 + depends on BR3_MACHINE_GPCM + bool "10 wait states" + +config OR3_SCY_11 + depends on BR3_MACHINE_GPCM + bool "11 wait states" + +config OR3_SCY_12 + depends on BR3_MACHINE_GPCM + bool "12 wait states" + +config OR3_SCY_13 + depends on BR3_MACHINE_GPCM + bool "13 wait states" + +config OR3_SCY_14 + depends on BR3_MACHINE_GPCM + bool "14 wait states" + +config OR3_SCY_15 + depends on BR3_MACHINE_GPCM + bool "15 wait states" + +endchoice + +endif # BR3_MACHINE_GPCM || BR3_MACHINE_FCM + +if BR3_MACHINE_GPCM + +choice + prompt "Chip select negotiation time" + +config OR3_CSNT_NORMAL + bool "Normal" + +config OR3_CSNT_EARLIER + bool "Earlier" + +endchoice + +choice + prompt "Address to chip-select setup" + +config OR3_ACS_SAME_TIME + bool "At the same time" + +config OR3_ACS_HALF_CYCLE_EARLIER + bool "Half of a bus clock cycle earlier" + +config OR3_ACS_QUARTER_CYCLE_EARLIER + bool "Half/Quarter of a bus clock cycle earlier" + +endchoice + +choice + prompt "Extra address to check-select setup" + +config OR3_XACS_NORMAL + bool "Normal" + +config OR3_XACS_EXTENDED + bool "Extended" + +endchoice + +choice + prompt "External address termination" + +config OR3_SETA_INTERNAL + bool "Access is terminated internally" + +config OR3_SETA_EXTERNAL + bool "Access is terminated externally" + +endchoice + +endif # BR3_MACHINE_GPCM + +if BR3_MACHINE_FCM + +choice + prompt "NAND Flash EEPROM page size" + +config OR3_PGS_SMALL + bool "Small page device" + +config OR3_PGS_LARGE + bool "Large page device" + +endchoice + +choice + prompt "Chip select to command time" + +config OR3_CSCT_1_CYCLE + depends on OR3_TRLX_NORMAL + bool "1 cycle" + +config OR3_CSCT_2_CYCLE + depends on OR3_TRLX_RELAXED + bool "2 cycles" + +config OR3_CSCT_4_CYCLE + depends on OR3_TRLX_NORMAL + bool "4 cycles" + +config OR3_CSCT_8_CYCLE + depends on OR3_TRLX_RELAXED + bool "8 cycles" + +endchoice + +choice + prompt "Command setup time" + +config OR3_CST_COINCIDENT + depends on OR3_TRLX_NORMAL + bool "Coincident with any command" + +config OR3_CST_QUARTER_CLOCK + depends on OR3_TRLX_NORMAL + bool "0.25 clocks after" + +config OR3_CST_HALF_CLOCK + depends on OR3_TRLX_RELAXED + bool "0.5 clocks after" + +config OR3_CST_ONE_CLOCK + depends on OR3_TRLX_RELAXED + bool "1 clock after" + +endchoice + +choice + prompt "Command hold time" + +config OR3_CHT_HALF_CLOCK + depends on OR3_TRLX_NORMAL + bool "0.5 clocks before" + +config OR3_CHT_ONE_CLOCK + depends on OR3_TRLX_NORMAL + bool "1 clock before" + +config OR3_CHT_ONE_HALF_CLOCK + depends on OR3_TRLX_RELAXED + bool "1.5 clocks before" + +config OR3_CHT_TWO_CLOCK + depends on OR3_TRLX_RELAXED + bool "2 clocks before" + +endchoice + +choice + prompt "Reset setup time" + +config OR3_RST_THREE_QUARTER_CLOCK + depends on OR3_TRLX_NORMAL + bool "0.75 clocks prior" + +config OR3_RST_ONE_HALF_CLOCK + depends on OR3_TRLX_RELAXED + bool "0.5 clocks prior" + +config OR3_RST_ONE_CLOCK + bool "1 clock prior" + +endchoice + +endif # BR3_MACHINE_FCM + +if BR3_MACHINE_UPM + +choice + prompt "Burst inhibit" + +config OR3_BI_BURSTSUPPORT + bool "Support burst access" + +config OR3_BI_BURSTINHIBIT + bool "Inhibit burst access" + +endchoice + +endif # BR3_MACHINE_UPM + +if BR3_MACHINE_SDRAM + +choice + prompt "Number of column address lines" + +config OR3_COLS_7 + bool "7" + +config OR3_COLS_8 + bool "8" + +config OR3_COLS_9 + bool "9" + +config OR3_COLS_10 + bool "10" + +config OR3_COLS_11 + bool "11" + +config OR3_COLS_12 + bool "12" + +config OR3_COLS_13 + bool "13" + +config OR3_COLS_14 + bool "14" + +endchoice + +choice + prompt "Number of rows address lines" + +config OR3_ROWS_9 + bool "9" + +config OR3_ROWS_10 + bool "10" + +config OR3_ROWS_11 + bool "11" + +config OR3_ROWS_12 + bool "12" + +config OR3_ROWS_13 + bool "13" + +config OR3_ROWS_14 + bool "14" + +config OR3_ROWS_15 + bool "15" + +endchoice + +choice + prompt "Page mode select" + +config OR3_PMSEL_BTB + bool "Back-to-back" + +config OR3_PMSEL_KEPT_OPEN + bool "Page kept open until page miss or refresh" + +endchoice + +endif # BR3_MACHINE_SDRAM + +choice + prompt "Relaxed timing" + +config OR3_TRLX_NORMAL + bool "Normal" + +config OR3_TRLX_RELAXED + bool "Relaxed" + +endchoice + +choice + prompt "Extended hold time" + +config OR3_EHTR_NORMAL + depends on OR3_TRLX_NORMAL + bool "Normal" + +config OR3_EHTR_1_CYCLE + depends on OR3_TRLX_NORMAL + bool "1 idle clock cycle inserted" + +config OR3_EHTR_4_CYCLE + depends on OR3_TRLX_RELAXED + bool "4 idle clock cycles inserted" + +config OR3_EHTR_8_CYCLE + depends on OR3_TRLX_RELAXED + bool "8 idle clock cycles inserted" + +endchoice + +if !ARCH_MPC8308 + +choice + prompt "External address latch delay" + +config OR3_EAD_NONE + bool "None" + +config OR3_EAD_EXTRA + bool "Extra" + +endchoice + +endif # !ARCH_MPC8308 + +endif # ELBC_BR3_OR3 + +config BR3_PORTSIZE + hex + default 0x800 if BR3_PORTSIZE_8BIT + default 0x1000 if BR3_PORTSIZE_16BIT + default 0x1800 if BR3_PORTSIZE_32BIT + +config BR3_ERRORCHECKING + hex + default 0x0 if !BR3_MACHINE_FCM + default 0x0 if BR3_ERRORCHECKING_DISABLED + default 0x200 if BR3_ERRORCHECKING_ECC_CHECKING + default 0x400 if BR3_ERRORCHECKING_BOTH + +config BR3_WRITE_PROTECT_BIT + hex + default 0x0 if !BR3_WRITE_PROTECT + default 0x100 if BR3_WRITE_PROTECT + +config BR3_MACHINE + hex + default 0x0 if BR3_MACHINE_GPCM + default 0x20 if BR3_MACHINE_FCM + default 0x60 if BR3_MACHINE_SDRAM + default 0x80 if BR3_MACHINE_UPMA + default 0xa0 if BR3_MACHINE_UPMB + default 0xc0 if BR3_MACHINE_UPMC + +config BR3_ATOMIC + hex + default 0x0 if !ARCH_MPC8313 && !ARCH_MPC8323 && !ARCH_MPC8360 + default 0x0 if BR3_ATOMIC_NONE + default 0x4 if BR3_ATOMIC_RAWA + default 0x8 if BR3_ATOMIC_WARA + +config BR3_VALID_BIT + hex + default 0x0 if !ELBC_BR3_OR3 + default 0x1 if ELBC_BR3_OR3 + +config OR3_AM + hex + default 0xffff8000 if OR3_AM_32_KBYTES && !BR3_MACHINE_SDRAM + default 0xffff0000 if OR3_AM_64_KBYTES + default 0xfffe0000 if OR3_AM_128_KBYTES + default 0xfffc0000 if OR3_AM_256_KBYTES + default 0xfff80000 if OR3_AM_512_KBYTES + default 0xfff00000 if OR3_AM_1_MBYTES + default 0xffe00000 if OR3_AM_2_MBYTES + default 0xffc00000 if OR3_AM_4_MBYTES + default 0xff800000 if OR3_AM_8_MBYTES + default 0xff000000 if OR3_AM_16_MBYTES + default 0xfe000000 if OR3_AM_32_MBYTES + default 0xfc000000 if OR3_AM_64_MBYTES + default 0xf8000000 if OR3_AM_128_MBYTES + default 0xf0000000 if OR3_AM_256_MBYTES + default 0xe0000000 if OR3_AM_512_MBYTES + default 0xc0000000 if OR3_AM_1_GBYTES + default 0x80000000 if OR3_AM_2_GBYTES + default 0x00000000 if OR3_AM_4_GBYTES + +config OR3_XAM + hex + default 0x0 if !OR3_XAM_SET + default 0x6000 if OR3_XAM_SET + +config OR3_BCTLD + hex + default 0x0 if OR3_BCTLD_ASSERTED + default 0x1000 if OR3_BCTLD_NOT_ASSERTED + +config OR3_BI + hex + default 0x0 if !BR3_MACHINE_UPM + default 0x0 if OR3_BI_BURSTSUPPORT + default 0x100 if OR3_BI_BURSTINHIBIT + +config OR3_COLS + hex + default 0x0 if !BR3_MACHINE_SDRAM + default 0x0 if OR3_COLS_7 + default 0x400 if OR3_COLS_8 + default 0x800 if OR3_COLS_9 + default 0xc00 if OR3_COLS_10 + default 0x1000 if OR3_COLS_11 + default 0x1400 if OR3_COLS_12 + default 0x1800 if OR3_COLS_13 + default 0x1c00 if OR3_COLS_14 + +config OR3_ROWS + hex + default 0x0 if !BR3_MACHINE_SDRAM + default 0x0 if OR3_ROWS_9 + default 0x40 if OR3_ROWS_10 + default 0x80 if OR3_ROWS_11 + default 0xc0 if OR3_ROWS_12 + default 0x100 if OR3_ROWS_13 + default 0x140 if OR3_ROWS_14 + default 0x180 if OR3_ROWS_15 + +config OR3_PMSEL + hex + default 0x0 if !BR3_MACHINE_SDRAM + default 0x0 if OR3_PMSEL_BTB + default 0x20 if OR3_PMSEL_KEPT_OPEN + +config OR3_SCY + hex + default 0x0 if !BR3_MACHINE_GPCM && !BR3_MACHINE_FCM + default 0x0 if OR3_SCY_0 + default 0x10 if OR3_SCY_1 + default 0x20 if OR3_SCY_2 + default 0x30 if OR3_SCY_3 + default 0x40 if OR3_SCY_4 + default 0x50 if OR3_SCY_5 + default 0x60 if OR3_SCY_6 + default 0x70 if OR3_SCY_7 + default 0x80 if OR3_SCY_8 + default 0x90 if OR3_SCY_9 + default 0xa0 if OR3_SCY_10 + default 0xb0 if OR3_SCY_11 + default 0xc0 if OR3_SCY_12 + default 0xd0 if OR3_SCY_13 + default 0xe0 if OR3_SCY_14 + default 0xf0 if OR3_SCY_15 + +config OR3_PGS + hex + default 0x0 if !BR3_MACHINE_FCM + default 0x0 if OR3_PGS_SMALL + default 0x400 if OR3_PGS_LARGE + +config OR3_CSCT + hex + default 0x0 if !BR3_MACHINE_FCM + default 0x0 if OR3_CSCT_1_CYCLE + default 0x0 if OR3_CSCT_2_CYCLE + default 0x200 if OR3_CSCT_4_CYCLE + default 0x200 if OR3_CSCT_8_CYCLE + +config OR3_CST + hex + default 0x0 if !BR3_MACHINE_FCM + default 0x0 if OR3_CST_COINCIDENT + default 0x100 if OR3_CST_QUARTER_CLOCK + default 0x0 if OR3_CST_HALF_CLOCK + default 0x100 if OR3_CST_ONE_CLOCK + +config OR3_CHT + hex + default 0x0 if !BR3_MACHINE_FCM + default 0x0 if OR3_CHT_HALF_CLOCK + default 0x80 if OR3_CHT_ONE_CLOCK + default 0x0 if OR3_CHT_ONE_HALF_CLOCK + default 0x80 if OR3_CHT_TWO_CLOCK + +config OR3_RST + hex + default 0x0 if !BR3_MACHINE_FCM + default 0x0 if OR3_RST_THREE_QUARTER_CLOCK + default 0x8 if OR3_RST_ONE_CLOCK + default 0x0 if OR3_RST_ONE_HALF_CLOCK + +config OR3_CSNT + hex + default 0x0 if !BR3_MACHINE_GPCM + default 0x0 if OR3_CSNT_NORMAL + default 0x800 if OR3_CSNT_EARLIER + +config OR3_ACS + hex + default 0x0 if !BR3_MACHINE_GPCM + default 0x0 if OR3_ACS_SAME_TIME + default 0x400 if OR3_ACS_QUARTER_CYCLE_EARLIER + default 0x600 if OR3_ACS_HALF_CYCLE_EARLIER + +config OR3_XACS + hex + default 0x0 if !BR3_MACHINE_GPCM + default 0x0 if OR3_XACS_NORMAL + default 0x100 if OR3_XACS_EXTENDED + +config OR3_SETA + hex + default 0x0 if !BR3_MACHINE_GPCM + default 0x0 if OR3_SETA_INTERNAL + default 0x8 if OR3_SETA_EXTERNAL + +config OR3_TRLX + hex + default 0x0 if OR3_TRLX_NORMAL + default 0x4 if OR3_TRLX_RELAXED + +config OR3_EHTR + hex + default 0x0 if OR3_EHTR_NORMAL + default 0x2 if OR3_EHTR_1_CYCLE + default 0x0 if OR3_EHTR_4_CYCLE + default 0x2 if OR3_EHTR_8_CYCLE + +config OR3_EAD + hex + default 0x0 if ARCH_MPC8308 + default 0x0 if OR3_EAD_NONE + default 0x1 if OR3_EAD_EXTRA diff --git a/arch/powerpc/cpu/mpc83xx/elbc/Kconfig.elbc4 b/arch/powerpc/cpu/mpc83xx/elbc/Kconfig.elbc4 new file mode 100644 index 0000000000..0063dab962 --- /dev/null +++ b/arch/powerpc/cpu/mpc83xx/elbc/Kconfig.elbc4 @@ -0,0 +1,733 @@ +menuconfig ELBC_BR4_OR4 + bool "ELBC BR4/OR4" + +if ELBC_BR4_OR4 + +config BR4_OR4_NAME + string "Identifier" + +config BR4_OR4_BASE + hex "Port base" + +choice + prompt "Port size" + +config BR4_PORTSIZE_8BIT + bool "8-bit" + +config BR4_PORTSIZE_16BIT + depends on !BR4_MACHINE_FCM + bool "16-bit" + + +config BR4_PORTSIZE_32BIT + depends on !BR4_MACHINE_FCM + depends on ARCH_MPC8349 || ARCH_MPC8360 || ARCH_MPC8379 + bool "32-bit" + +endchoice + +if BR4_MACHINE_FCM + +choice + prompt "Data Error Checking" + +config BR4_ERRORCHECKING_DISABLED + bool "Disabled" + +config BR4_ERRORCHECKING_ECC_CHECKING + bool "ECC checking / No ECC generation" + +config BR4_ERRORCHECKING_BOTH + bool "ECC checking and generation" + +endchoice + +endif + +config BR4_WRITE_PROTECT + bool "Write-protect" + +config BR4_MACHINE_UPM + bool + +choice + prompt "Machine select" + +config BR4_MACHINE_GPCM + bool "GPCM" + +config BR4_MACHINE_FCM + depends on !ARCH_MPC832X && !ARCH_MPC8349 && !ARCH_MPC8360 + bool "FCM" + +config BR4_MACHINE_SDRAM + depends on ARCH_MPC8349 || ARCH_MPC8360 + bool "SDRAM" + +config BR4_MACHINE_UPMA + select BR4_MACHINE_UPM + bool "UPM (A)" + +config BR4_MACHINE_UPMB + select BR4_MACHINE_UPM + bool "UPM (B)" + +config BR4_MACHINE_UPMC + select BR4_MACHINE_UPM + bool "UPM (C)" + +endchoice + +if ARCH_MPC8313 || ARCH_MPC8323 || ARCH_MPC8360 + +choice + prompt "Atomic operations" + +config BR4_ATOMIC_NONE + bool "No atomic operations" + +config BR4_ATOMIC_RAWA + bool "Read-after-write-atomic" + +config BR4_ATOMIC_WARA + bool "Write-after-read-atomic" + +endchoice + +endif + +if BR4_MACHINE_GPCM || BR4_MACHINE_FCM || BR4_MACHINE_UPM || BR4_MACHINE_SDRAM + +choice + prompt "Address mask" + +config OR4_AM_32_KBYTES + depends on !BR4_MACHINE_SDRAM + bool "32 kb" + +config OR4_AM_64_KBYTES + bool "64 kb" + +config OR4_AM_128_KBYTES + bool "128 kb" + +config OR4_AM_256_KBYTES + bool "256 kb" + +config OR4_AM_512_KBYTES + bool "512 kb" + +config OR4_AM_1_MBYTES + bool "1 mb" + +config OR4_AM_2_MBYTES + bool "2 mb" + +config OR4_AM_4_MBYTES + bool "4 mb" + +config OR4_AM_8_MBYTES + bool "8 mb" + +config OR4_AM_16_MBYTES + bool "16 mb" + +config OR4_AM_32_MBYTES + bool "32 mb" + +config OR4_AM_64_MBYTES + bool "64 mb" + +# XXX: Some boards define 128MB AM with GPCM, even though it should not be +# possible according to the manuals +config OR4_AM_128_MBYTES + bool "128 mb" + +# XXX: Some boards define 256MB AM with GPCM, even though it should not be +# possible according to the manuals +config OR4_AM_256_MBYTES + bool "256 mb" + +config OR4_AM_512_MBYTES + depends on BR4_MACHINE_FCM + bool "512 mb" + +# XXX: Some boards define 1GB AM with GPCM, even though it should not be +# possible according to the manuals +config OR4_AM_1_GBYTES + bool "1 gb" + +config OR4_AM_2_GBYTES + depends on BR4_MACHINE_FCM + bool "2 gb" + +config OR4_AM_4_GBYTES + depends on BR4_MACHINE_FCM + bool "4 gb" + +endchoice + +config OR4_XAM_SET + bool "Set unused bytes after address mask" +choice + prompt "Buffer control disable" + +config OR4_BCTLD_ASSERTED + bool "Asserted" + +config OR4_BCTLD_NOT_ASSERTED + bool "Not asserted" + +endchoice + +endif + +if BR4_MACHINE_GPCM || BR4_MACHINE_FCM + +choice + prompt "Cycle length in bus clocks" + +config OR4_SCY_0 + bool "No wait states" + +config OR4_SCY_1 + bool "1 wait state" + +config OR4_SCY_2 + bool "2 wait states" + +config OR4_SCY_3 + bool "3 wait states" + +config OR4_SCY_4 + bool "4 wait states" + +config OR4_SCY_5 + bool "5 wait states" + +config OR4_SCY_6 + bool "6 wait states" + +config OR4_SCY_7 + bool "7 wait states" + +config OR4_SCY_8 + depends on BR4_MACHINE_GPCM + bool "8 wait states" + +config OR4_SCY_9 + depends on BR4_MACHINE_GPCM + bool "9 wait states" + +config OR4_SCY_10 + depends on BR4_MACHINE_GPCM + bool "10 wait states" + +config OR4_SCY_11 + depends on BR4_MACHINE_GPCM + bool "11 wait states" + +config OR4_SCY_12 + depends on BR4_MACHINE_GPCM + bool "12 wait states" + +config OR4_SCY_13 + depends on BR4_MACHINE_GPCM + bool "13 wait states" + +config OR4_SCY_14 + depends on BR4_MACHINE_GPCM + bool "14 wait states" + +config OR4_SCY_15 + depends on BR4_MACHINE_GPCM + bool "15 wait states" + +endchoice + +endif # BR4_MACHINE_GPCM || BR4_MACHINE_FCM + +if BR4_MACHINE_GPCM + +choice + prompt "Chip select negotiation time" + +config OR4_CSNT_NORMAL + bool "Normal" + +config OR4_CSNT_EARLIER + bool "Earlier" + +endchoice + +choice + prompt "Address to chip-select setup" + +config OR4_ACS_SAME_TIME + bool "At the same time" + +config OR4_ACS_HALF_CYCLE_EARLIER + bool "Half of a bus clock cycle earlier" + +config OR4_ACS_QUARTER_CYCLE_EARLIER + bool "Half/Quarter of a bus clock cycle earlier" + +endchoice + +choice + prompt "Extra address to check-select setup" + +config OR4_XACS_NORMAL + bool "Normal" + +config OR4_XACS_EXTENDED + bool "Extended" + +endchoice + +choice + prompt "External address termination" + +config OR4_SETA_INTERNAL + bool "Access is terminated internally" + +config OR4_SETA_EXTERNAL + bool "Access is terminated externally" + +endchoice + +endif # BR4_MACHINE_GPCM + +if BR4_MACHINE_FCM + +choice + prompt "NAND Flash EEPROM page size" + +config OR4_PGS_SMALL + bool "Small page device" + +config OR4_PGS_LARGE + bool "Large page device" + +endchoice + +choice + prompt "Chip select to command time" + +config OR4_CSCT_1_CYCLE + depends on OR4_TRLX_NORMAL + bool "1 cycle" + +config OR4_CSCT_2_CYCLE + depends on OR4_TRLX_RELAXED + bool "2 cycles" + +config OR4_CSCT_4_CYCLE + depends on OR4_TRLX_NORMAL + bool "4 cycles" + +config OR4_CSCT_8_CYCLE + depends on OR4_TRLX_RELAXED + bool "8 cycles" + +endchoice + +choice + prompt "Command setup time" + +config OR4_CST_COINCIDENT + depends on OR4_TRLX_NORMAL + bool "Coincident with any command" + +config OR4_CST_QUARTER_CLOCK + depends on OR4_TRLX_NORMAL + bool "0.25 clocks after" + +config OR4_CST_HALF_CLOCK + depends on OR4_TRLX_RELAXED + bool "0.5 clocks after" + +config OR4_CST_ONE_CLOCK + depends on OR4_TRLX_RELAXED + bool "1 clock after" + +endchoice + +choice + prompt "Command hold time" + +config OR4_CHT_HALF_CLOCK + depends on OR4_TRLX_NORMAL + bool "0.5 clocks before" + +config OR4_CHT_ONE_CLOCK + depends on OR4_TRLX_NORMAL + bool "1 clock before" + +config OR4_CHT_ONE_HALF_CLOCK + depends on OR4_TRLX_RELAXED + bool "1.5 clocks before" + +config OR4_CHT_TWO_CLOCK + depends on OR4_TRLX_RELAXED + bool "2 clocks before" + +endchoice + +choice + prompt "Reset setup time" + +config OR4_RST_THREE_QUARTER_CLOCK + depends on OR4_TRLX_NORMAL + bool "0.75 clocks prior" + +config OR4_RST_ONE_HALF_CLOCK + depends on OR4_TRLX_RELAXED + bool "0.5 clocks prior" + +config OR4_RST_ONE_CLOCK + bool "1 clock prior" + +endchoice + +endif # BR4_MACHINE_FCM + +if BR4_MACHINE_UPM + +choice + prompt "Burst inhibit" + +config OR4_BI_BURSTSUPPORT + bool "Support burst access" + +config OR4_BI_BURSTINHIBIT + bool "Inhibit burst access" + +endchoice + +endif # BR4_MACHINE_UPM + +if BR4_MACHINE_SDRAM + +choice + prompt "Number of column address lines" + +config OR4_COLS_7 + bool "7" + +config OR4_COLS_8 + bool "8" + +config OR4_COLS_9 + bool "9" + +config OR4_COLS_10 + bool "10" + +config OR4_COLS_11 + bool "11" + +config OR4_COLS_12 + bool "12" + +config OR4_COLS_13 + bool "13" + +config OR4_COLS_14 + bool "14" + +endchoice + +choice + prompt "Number of rows address lines" + +config OR4_ROWS_9 + bool "9" + +config OR4_ROWS_10 + bool "10" + +config OR4_ROWS_11 + bool "11" + +config OR4_ROWS_12 + bool "12" + +config OR4_ROWS_13 + bool "13" + +config OR4_ROWS_14 + bool "14" + +config OR4_ROWS_15 + bool "15" + +endchoice + +choice + prompt "Page mode select" + +config OR4_PMSEL_BTB + bool "Back-to-back" + +config OR4_PMSEL_KEPT_OPEN + bool "Page kept open until page miss or refresh" + +endchoice + +endif # BR4_MACHINE_SDRAM + +choice + prompt "Relaxed timing" + +config OR4_TRLX_NORMAL + bool "Normal" + +config OR4_TRLX_RELAXED + bool "Relaxed" + +endchoice + +choice + prompt "Extended hold time" + +config OR4_EHTR_NORMAL + depends on OR4_TRLX_NORMAL + bool "Normal" + +config OR4_EHTR_1_CYCLE + depends on OR4_TRLX_NORMAL + bool "1 idle clock cycle inserted" + +config OR4_EHTR_4_CYCLE + depends on OR4_TRLX_RELAXED + bool "4 idle clock cycles inserted" + +config OR4_EHTR_8_CYCLE + depends on OR4_TRLX_RELAXED + bool "8 idle clock cycles inserted" + +endchoice + +if !ARCH_MPC8308 + +choice + prompt "External address latch delay" + +config OR4_EAD_NONE + bool "None" + +config OR4_EAD_EXTRA + bool "Extra" + +endchoice + +endif # !ARCH_MPC8308 + +endif # ELBC_BR4_OR4 + +config BR4_PORTSIZE + hex + default 0x800 if BR4_PORTSIZE_8BIT + default 0x1000 if BR4_PORTSIZE_16BIT + default 0x1800 if BR4_PORTSIZE_32BIT + +config BR4_ERRORCHECKING + hex + default 0x0 if !BR4_MACHINE_FCM + default 0x0 if BR4_ERRORCHECKING_DISABLED + default 0x200 if BR4_ERRORCHECKING_ECC_CHECKING + default 0x400 if BR4_ERRORCHECKING_BOTH + +config BR4_WRITE_PROTECT_BIT + hex + default 0x0 if !BR4_WRITE_PROTECT + default 0x100 if BR4_WRITE_PROTECT + +config BR4_MACHINE + hex + default 0x0 if BR4_MACHINE_GPCM + default 0x20 if BR4_MACHINE_FCM + default 0x60 if BR4_MACHINE_SDRAM + default 0x80 if BR4_MACHINE_UPMA + default 0xa0 if BR4_MACHINE_UPMB + default 0xc0 if BR4_MACHINE_UPMC + +config BR4_ATOMIC + hex + default 0x0 if !ARCH_MPC8313 && !ARCH_MPC8323 && !ARCH_MPC8360 + default 0x0 if BR4_ATOMIC_NONE + default 0x4 if BR4_ATOMIC_RAWA + default 0x8 if BR4_ATOMIC_WARA + +config BR4_VALID_BIT + hex + default 0x0 if !ELBC_BR4_OR4 + default 0x1 if ELBC_BR4_OR4 + +config OR4_AM + hex + default 0xffff8000 if OR4_AM_32_KBYTES && !BR4_MACHINE_SDRAM + default 0xffff0000 if OR4_AM_64_KBYTES + default 0xfffe0000 if OR4_AM_128_KBYTES + default 0xfffc0000 if OR4_AM_256_KBYTES + default 0xfff80000 if OR4_AM_512_KBYTES + default 0xfff00000 if OR4_AM_1_MBYTES + default 0xffe00000 if OR4_AM_2_MBYTES + default 0xffc00000 if OR4_AM_4_MBYTES + default 0xff800000 if OR4_AM_8_MBYTES + default 0xff000000 if OR4_AM_16_MBYTES + default 0xfe000000 if OR4_AM_32_MBYTES + default 0xfc000000 if OR4_AM_64_MBYTES + default 0xf8000000 if OR4_AM_128_MBYTES + default 0xf0000000 if OR4_AM_256_MBYTES + default 0xe0000000 if OR4_AM_512_MBYTES + default 0xc0000000 if OR4_AM_1_GBYTES + default 0x80000000 if OR4_AM_2_GBYTES + default 0x00000000 if OR4_AM_4_GBYTES + +config OR4_XAM + hex + default 0x0 if !OR4_XAM_SET + default 0x6000 if OR4_XAM_SET + +config OR4_BCTLD + hex + default 0x0 if OR4_BCTLD_ASSERTED + default 0x1000 if OR4_BCTLD_NOT_ASSERTED + +config OR4_BI + hex + default 0x0 if !BR4_MACHINE_UPM + default 0x0 if OR4_BI_BURSTSUPPORT + default 0x100 if OR4_BI_BURSTINHIBIT + +config OR4_COLS + hex + default 0x0 if !BR4_MACHINE_SDRAM + default 0x0 if OR4_COLS_7 + default 0x400 if OR4_COLS_8 + default 0x800 if OR4_COLS_9 + default 0xc00 if OR4_COLS_10 + default 0x1000 if OR4_COLS_11 + default 0x1400 if OR4_COLS_12 + default 0x1800 if OR4_COLS_13 + default 0x1c00 if OR4_COLS_14 + +config OR4_ROWS + hex + default 0x0 if !BR4_MACHINE_SDRAM + default 0x0 if OR4_ROWS_9 + default 0x40 if OR4_ROWS_10 + default 0x80 if OR4_ROWS_11 + default 0xc0 if OR4_ROWS_12 + default 0x100 if OR4_ROWS_13 + default 0x140 if OR4_ROWS_14 + default 0x180 if OR4_ROWS_15 + +config OR4_PMSEL + hex + default 0x0 if !BR4_MACHINE_SDRAM + default 0x0 if OR4_PMSEL_BTB + default 0x20 if OR4_PMSEL_KEPT_OPEN + +config OR4_SCY + hex + default 0x0 if !BR4_MACHINE_GPCM && !BR4_MACHINE_FCM + default 0x0 if OR4_SCY_0 + default 0x10 if OR4_SCY_1 + default 0x20 if OR4_SCY_2 + default 0x30 if OR4_SCY_3 + default 0x40 if OR4_SCY_4 + default 0x50 if OR4_SCY_5 + default 0x60 if OR4_SCY_6 + default 0x70 if OR4_SCY_7 + default 0x80 if OR4_SCY_8 + default 0x90 if OR4_SCY_9 + default 0xa0 if OR4_SCY_10 + default 0xb0 if OR4_SCY_11 + default 0xc0 if OR4_SCY_12 + default 0xd0 if OR4_SCY_13 + default 0xe0 if OR4_SCY_14 + default 0xf0 if OR4_SCY_15 + +config OR4_PGS + hex + default 0x0 if !BR4_MACHINE_FCM + default 0x0 if OR4_PGS_SMALL + default 0x400 if OR4_PGS_LARGE + +config OR4_CSCT + hex + default 0x0 if !BR4_MACHINE_FCM + default 0x0 if OR4_CSCT_1_CYCLE + default 0x0 if OR4_CSCT_2_CYCLE + default 0x200 if OR4_CSCT_4_CYCLE + default 0x200 if OR4_CSCT_8_CYCLE + +config OR4_CST + hex + default 0x0 if !BR4_MACHINE_FCM + default 0x0 if OR4_CST_COINCIDENT + default 0x100 if OR4_CST_QUARTER_CLOCK + default 0x0 if OR4_CST_HALF_CLOCK + default 0x100 if OR4_CST_ONE_CLOCK + +config OR4_CHT + hex + default 0x0 if !BR4_MACHINE_FCM + default 0x0 if OR4_CHT_HALF_CLOCK + default 0x80 if OR4_CHT_ONE_CLOCK + default 0x0 if OR4_CHT_ONE_HALF_CLOCK + default 0x80 if OR4_CHT_TWO_CLOCK + +config OR4_RST + hex + default 0x0 if !BR4_MACHINE_FCM + default 0x0 if OR4_RST_THREE_QUARTER_CLOCK + default 0x8 if OR4_RST_ONE_CLOCK + default 0x0 if OR4_RST_ONE_HALF_CLOCK + +config OR4_CSNT + hex + default 0x0 if !BR4_MACHINE_GPCM + default 0x0 if OR4_CSNT_NORMAL + default 0x800 if OR4_CSNT_EARLIER + +config OR4_ACS + hex + default 0x0 if !BR4_MACHINE_GPCM + default 0x0 if OR4_ACS_SAME_TIME + default 0x400 if OR4_ACS_QUARTER_CYCLE_EARLIER + default 0x600 if OR4_ACS_HALF_CYCLE_EARLIER + +config OR4_XACS + hex + default 0x0 if !BR4_MACHINE_GPCM + default 0x0 if OR4_XACS_NORMAL + default 0x100 if OR4_XACS_EXTENDED + +config OR4_SETA + hex + default 0x0 if !BR4_MACHINE_GPCM + default 0x0 if OR4_SETA_INTERNAL + default 0x8 if OR4_SETA_EXTERNAL + +config OR4_TRLX + hex + default 0x0 if OR4_TRLX_NORMAL + default 0x4 if OR4_TRLX_RELAXED + +config OR4_EHTR + hex + default 0x0 if OR4_EHTR_NORMAL + default 0x2 if OR4_EHTR_1_CYCLE + default 0x0 if OR4_EHTR_4_CYCLE + default 0x2 if OR4_EHTR_8_CYCLE + +config OR4_EAD + hex + default 0x0 if ARCH_MPC8308 + default 0x0 if OR4_EAD_NONE + default 0x1 if OR4_EAD_EXTRA diff --git a/arch/powerpc/cpu/mpc83xx/elbc/elbc.h b/arch/powerpc/cpu/mpc83xx/elbc/elbc.h new file mode 100644 index 0000000000..245fe7c6fb --- /dev/null +++ b/arch/powerpc/cpu/mpc83xx/elbc/elbc.h @@ -0,0 +1,186 @@ +#ifdef CONFIG_ELBC_BR0_OR0 +#define CONFIG_SYS_BR0_PRELIM (\ + CONFIG_BR0_OR0_BASE |\ + CONFIG_BR0_PORTSIZE |\ + CONFIG_BR0_ERRORCHECKING |\ + CONFIG_BR0_WRITE_PROTECT_BIT |\ + CONFIG_BR0_MACHINE |\ + CONFIG_BR0_ATOMIC |\ + CONFIG_BR0_VALID_BIT \ +) +#define CONFIG_SYS_OR0_PRELIM (\ + CONFIG_OR0_AM |\ + CONFIG_OR0_XAM |\ + CONFIG_OR0_BCTLD |\ + CONFIG_OR0_BI |\ + CONFIG_OR0_COLS |\ + CONFIG_OR0_ROWS |\ + CONFIG_OR0_PMSEL |\ + CONFIG_OR0_SCY |\ + CONFIG_OR0_PGS |\ + CONFIG_OR0_CSCT |\ + CONFIG_OR0_CST |\ + CONFIG_OR0_CHT |\ + CONFIG_OR0_RST |\ + CONFIG_OR0_CSNT |\ + CONFIG_OR0_ACS |\ + CONFIG_OR0_XACS |\ + CONFIG_OR0_SETA |\ + CONFIG_OR0_TRLX |\ + CONFIG_OR0_EHTR |\ + CONFIG_OR0_EAD \ +) +#endif /* CONFIG_ELBC_BR0_OR0 */ + +#ifdef CONFIG_ELBC_BR1_OR1 +#define CONFIG_SYS_BR1_PRELIM (\ + CONFIG_BR1_OR1_BASE |\ + CONFIG_BR1_PORTSIZE |\ + CONFIG_BR1_ERRORCHECKING |\ + CONFIG_BR1_WRITE_PROTECT_BIT |\ + CONFIG_BR1_MACHINE |\ + CONFIG_BR1_ATOMIC |\ + CONFIG_BR1_VALID_BIT \ +) +#define CONFIG_SYS_OR1_PRELIM (\ + CONFIG_OR1_AM |\ + CONFIG_OR1_XAM |\ + CONFIG_OR1_BCTLD |\ + CONFIG_OR1_BI |\ + CONFIG_OR1_COLS |\ + CONFIG_OR1_ROWS |\ + CONFIG_OR1_PMSEL |\ + CONFIG_OR1_SCY |\ + CONFIG_OR1_PGS |\ + CONFIG_OR1_CSCT |\ + CONFIG_OR1_CST |\ + CONFIG_OR1_CHT |\ + CONFIG_OR1_RST |\ + CONFIG_OR1_CSNT |\ + CONFIG_OR1_ACS |\ + CONFIG_OR1_XACS |\ + CONFIG_OR1_SETA |\ + CONFIG_OR1_TRLX |\ + CONFIG_OR1_EHTR |\ + CONFIG_OR1_EAD \ +) +#endif /* CONFIG_ELBC_BR1_OR1 */ + +#ifdef CONFIG_ELBC_BR2_OR2 +#define CONFIG_SYS_BR2_PRELIM (\ + CONFIG_BR2_OR2_BASE |\ + CONFIG_BR2_PORTSIZE |\ + CONFIG_BR2_ERRORCHECKING |\ + CONFIG_BR2_WRITE_PROTECT_BIT |\ + CONFIG_BR2_MACHINE |\ + CONFIG_BR2_ATOMIC |\ + CONFIG_BR2_VALID_BIT \ +) +#define CONFIG_SYS_OR2_PRELIM (\ + CONFIG_OR2_AM |\ + CONFIG_OR2_XAM |\ + CONFIG_OR2_BCTLD |\ + CONFIG_OR2_BI |\ + CONFIG_OR2_COLS |\ + CONFIG_OR2_ROWS |\ + CONFIG_OR2_PMSEL |\ + CONFIG_OR2_SCY |\ + CONFIG_OR2_PGS |\ + CONFIG_OR2_CSCT |\ + CONFIG_OR2_CST |\ + CONFIG_OR2_CHT |\ + CONFIG_OR2_RST |\ + CONFIG_OR2_CSNT |\ + CONFIG_OR2_ACS |\ + CONFIG_OR2_XACS |\ + CONFIG_OR2_SETA |\ + CONFIG_OR2_TRLX |\ + CONFIG_OR2_EHTR |\ + CONFIG_OR2_EAD \ +) +#endif /* CONFIG_ELBC_BR2_OR2 */ + +#ifdef CONFIG_ELBC_BR3_OR3 +#define CONFIG_SYS_BR3_PRELIM (\ + CONFIG_BR3_OR3_BASE |\ + CONFIG_BR3_PORTSIZE |\ + CONFIG_BR3_ERRORCHECKING |\ + CONFIG_BR3_WRITE_PROTECT_BIT |\ + CONFIG_BR3_MACHINE |\ + CONFIG_BR3_ATOMIC |\ + CONFIG_BR3_VALID_BIT \ +) +#define CONFIG_SYS_OR3_PRELIM (\ + CONFIG_OR3_AM |\ + CONFIG_OR3_XAM |\ + CONFIG_OR3_BCTLD |\ + CONFIG_OR3_BI |\ + CONFIG_OR3_COLS |\ + CONFIG_OR3_ROWS |\ + CONFIG_OR3_PMSEL |\ + CONFIG_OR3_SCY |\ + CONFIG_OR3_PGS |\ + CONFIG_OR3_CSCT |\ + CONFIG_OR3_CST |\ + CONFIG_OR3_CHT |\ + CONFIG_OR3_RST |\ + CONFIG_OR3_CSNT |\ + CONFIG_OR3_ACS |\ + CONFIG_OR3_XACS |\ + CONFIG_OR3_SETA |\ + CONFIG_OR3_TRLX |\ + CONFIG_OR3_EHTR |\ + CONFIG_OR3_EAD \ +) +#endif /* CONFIG_ELBC_BR3_OR3 */ + +#ifdef CONFIG_ELBC_BR4_OR4 +#define CONFIG_SYS_BR4_PRELIM (\ + CONFIG_BR4_OR4_BASE |\ + CONFIG_BR4_PORTSIZE |\ + CONFIG_BR4_ERRORCHECKING |\ + CONFIG_BR4_WRITE_PROTECT_BIT |\ + CONFIG_BR4_MACHINE |\ + CONFIG_BR4_ATOMIC |\ + CONFIG_BR4_VALID_BIT \ +) +#define CONFIG_SYS_OR4_PRELIM (\ + CONFIG_OR4_AM |\ + CONFIG_OR4_XAM |\ + CONFIG_OR4_BCTLD |\ + CONFIG_OR4_BI |\ + CONFIG_OR4_COLS |\ + CONFIG_OR4_ROWS |\ + CONFIG_OR4_PMSEL |\ + CONFIG_OR4_SCY |\ + CONFIG_OR4_PGS |\ + CONFIG_OR4_CSCT |\ + CONFIG_OR4_CST |\ + CONFIG_OR4_CHT |\ + CONFIG_OR4_RST |\ + CONFIG_OR4_CSNT |\ + CONFIG_OR4_ACS |\ + CONFIG_OR4_XACS |\ + CONFIG_OR4_SETA |\ + CONFIG_OR4_TRLX |\ + CONFIG_OR4_EHTR |\ + CONFIG_OR4_EAD \ +) +#endif /* CONFIG_ELBC_BR4_OR4 */ + +#if defined(CONFIG_ELBC_BR_OR_NAND_PRELIM_0) +#define CONFIG_SYS_NAND_BR_PRELIM CONFIG_SYS_BR0_PRELIM +#define CONFIG_SYS_NAND_OR_PRELIM CONFIG_SYS_OR0_PRELIM +#elif defined(CONFIG_ELBC_BR_OR_NAND_PRELIM_1) +#define CONFIG_SYS_NAND_BR_PRELIM CONFIG_SYS_BR1_PRELIM +#define CONFIG_SYS_NAND_OR_PRELIM CONFIG_SYS_OR1_PRELIM +#elif defined(CONFIG_ELBC_BR_OR_NAND_PRELIM_2) +#define CONFIG_SYS_NAND_BR_PRELIM CONFIG_SYS_BR2_PRELIM +#define CONFIG_SYS_NAND_OR_PRELIM CONFIG_SYS_OR2_PRELIM +#elif defined(CONFIG_ELBC_BR_OR_NAND_PRELIM_3) +#define CONFIG_SYS_NAND_BR_PRELIM CONFIG_SYS_BR3_PRELIM +#define CONFIG_SYS_NAND_OR_PRELIM CONFIG_SYS_OR3_PRELIM +#elif defined(CONFIG_ELBC_BR_OR_NAND_PRELIM_4) +#define CONFIG_SYS_NAND_BR_PRELIM CONFIG_SYS_BR4_PRELIM +#define CONFIG_SYS_NAND_OR_PRELIM CONFIG_SYS_OR4_PRELIM +#endif diff --git a/arch/powerpc/cpu/mpc83xx/fdt.c b/arch/powerpc/cpu/mpc83xx/fdt.c index 0ecafd708f..b487e31cc0 100644 --- a/arch/powerpc/cpu/mpc83xx/fdt.c +++ b/arch/powerpc/cpu/mpc83xx/fdt.c @@ -16,7 +16,7 @@ extern void ft_qe_setup(void *blob); DECLARE_GLOBAL_DATA_PTR; #if defined(CONFIG_BOOTCOUNT_LIMIT) && \ - (defined(CONFIG_QE) && !defined(CONFIG_MPC831x)) + (defined(CONFIG_QE) && !defined(CONFIG_ARCH_MPC831X)) #include <linux/immap_qe.h> void fdt_fixup_muram (void *blob) @@ -52,7 +52,7 @@ void ft_cpu_setup(void *blob, bd_t *bd) #if defined(CONFIG_HAS_ETH0) || defined(CONFIG_HAS_ETH1) ||\ defined(CONFIG_HAS_ETH2) || defined(CONFIG_HAS_ETH3) ||\ defined(CONFIG_HAS_ETH4) || defined(CONFIG_HAS_ETH5) -#ifdef CONFIG_MPC8313 +#ifdef CONFIG_ARCH_MPC8313 /* * mpc8313e erratum IPIC1 swapped TSEC interrupt ID numbers on rev. 1 * h/w (see AN3545). The base device tree in use has rev. 1 ID numbers, @@ -116,14 +116,14 @@ void ft_cpu_setup(void *blob, bd_t *bd) #endif #ifdef CONFIG_SYS_NS16550 - do_fixup_by_compat_u32(blob, "ns16550", - "clock-frequency", CONFIG_SYS_NS16550_CLK, 1); + do_fixup_by_compat_u32(blob, "ns16550", + "clock-frequency", get_serial_clock(), 1); #endif fdt_fixup_memory(blob, (u64)bd->bi_memstart, (u64)bd->bi_memsize); #if defined(CONFIG_BOOTCOUNT_LIMIT) && \ - (defined(CONFIG_QE) && !defined(CONFIG_MPC831x)) + (defined(CONFIG_QE) && !defined(CONFIG_ARCH_MPC831X)) fdt_fixup_muram (blob); #endif } diff --git a/arch/powerpc/cpu/mpc83xx/hid/Kconfig b/arch/powerpc/cpu/mpc83xx/hid/Kconfig new file mode 100644 index 0000000000..c367ad2ce1 --- /dev/null +++ b/arch/powerpc/cpu/mpc83xx/hid/Kconfig @@ -0,0 +1,565 @@ +menu "HID setup" + +menu "HID0 initial" + +config HID0_INIT_EMCP + bool "Enable machine check int on mcp" + +config HID0_INIT_ECPE + bool "Enable cache parity errors" + +config HID0_INIT_EBA + bool "Enable address parity checking" + +config HID0_INIT_EBD + bool "Enable data parity checking" + +choice + prompt "HID0 clock configuration" + +config HID0_INIT_CLKOUT_OFF + bool "Clock output off" + +config HID0_INIT_CLKOUT_CORE_HALF + bool "Core clock / 2" + +config HID0_INIT_CLKOUT_CORE + bool "Core clock" + +config HID0_INIT_CLKOUT_BUS + bool "Bus clock" + +endchoice + +config HID0_INIT_PAR + bool "Disable precharge of artry_out" + +config HID0_INIT_DOZE + bool "Enable doze mode" + +config HID0_INIT_NAP + bool "Enable nap mode" + +config HID0_INIT_SLEEP + bool "Enable sleep mode" + +config HID0_INIT_DPM + bool "Enable dynamic power management" + +config HID0_INIT_ICE + bool "Enable instruction cache" + +config HID0_INIT_DCE + bool "Enable data cache" + +config HID0_INIT_ILOCK + bool "Lock instruction cache" + +config HID0_INIT_DLOCK + bool "Lock data cache" + +config HID0_INIT_ICFI + bool "Flash invalidate instruction cache" + +config HID0_INIT_DCFI + bool "Flash invalidate data cache" + +config HID0_INIT_IFEM + bool "Enable m bit on bus for instruction fetches" + +config HID0_INIT_DECAREN + bool "Decrementer auto reload" + +config HID0_INIT_FBIOB + bool "Force indirect branch on the bus" + +config HID0_INIT_ABE + bool "Enable address broadcast" + +config HID0_INIT_NOOPTI + bool "No-op data cache touch intructions" + +endmenu + +menu "HID0 final" + +config HID0_FINAL_EMCP + bool "Enable machine check int on mcp" + +config HID0_FINAL_ECPE + bool "Enable cache parity errors" + +config HID0_FINAL_EBA + bool "Enable address parity checking" + +config HID0_FINAL_EBD + bool "Enable data parity checking" + +choice + prompt "HID0 clock configuration" + +config HID0_FINAL_CLKOUT_OFF + bool "Clock output off" + +config HID0_FINAL_CLKOUT_CORE_HALF + bool "Core clock / 2" + +config HID0_FINAL_CLKOUT_CORE + bool "Core clock" + +config HID0_FINAL_CLKOUT_BUS + bool "Bus clock" + +endchoice + +config HID0_FINAL_PAR + bool "Disable precharge of artry_out" + +config HID0_FINAL_DOZE + bool "Enable doze mode" + +config HID0_FINAL_NAP + bool "Enable nap mode" + +config HID0_FINAL_SLEEP + bool "Enable sleep mode" + +config HID0_FINAL_DPM + bool "Enable dynamic power management" + +config HID0_FINAL_ICE + bool "Enable instruction cache" + +config HID0_FINAL_DCE + bool "Enable data cache" + +config HID0_FINAL_ILOCK + bool "Lock instruction cache" + +config HID0_FINAL_DLOCK + bool "Lock data cache" + +config HID0_FINAL_ICFI + bool "Flash invalidate instruction cache" + +config HID0_FINAL_DCFI + bool "Flash invalidate data cache" + +config HID0_FINAL_IFEM + bool "Enable m bit on bus for instruction fetches" + +config HID0_FINAL_DECAREN + bool "Decrementer auto reload" + +config HID0_FINAL_FBIOB + bool "Force indirect branch on the bus" + +config HID0_FINAL_ABE + bool "Enable address broadcast" + +config HID0_FINAL_NOOPTI + bool "No-op data cache touch intructions" + +endmenu + +config HID0_INIT_EMCP_BIT + hex + default 0x0 if !HID0_INIT_EMCP + default 0x80000000 if HID0_INIT_EMCP + +config HID0_INIT_ECPE_BIT + hex + default 0x0 if !HID0_INIT_ECPE + default 0x40000000 if HID0_INIT_ECPE + +config HID0_INIT_EBA_BIT + hex + default 0x0 if !HID0_INIT_EBA + default 0x20000000 if HID0_INIT_EBA + +config HID0_INIT_EBD_BIT + hex + default 0x0 if !HID0_INIT_EBD + default 0x10000000 if HID0_INIT_EBD + +config HID0_INIT_CLKOUT + hex + default 0x0 if HID0_INIT_CLKOUT_OFF + default 0x8000000 if HID0_INIT_CLKOUT_CORE_HALF + default 0x2000000 if HID0_INIT_CLKOUT_CORE + default 0xa000000 if HID0_INIT_CLKOUT_BUS + +config HID0_INIT_PAR_BIT + hex + default 0x0 if !HID0_INIT_PAR + default 0x1000000 if HID0_INIT_PAR + +config HID0_INIT_DOZE_BIT + hex + default 0x0 if !HID0_INIT_DOZE + default 0x800000 if HID0_INIT_DOZE + +config HID0_INIT_NAP_BIT + hex + default 0x0 if !HID0_INIT_NAP + default 0x400000 if HID0_INIT_NAP + +config HID0_INIT_SLEEP_BIT + hex + default 0x0 if !HID0_INIT_SLEEP + default 0x200000 if HID0_INIT_SLEEP + +config HID0_INIT_DPM_BIT + hex + default 0x0 if !HID0_INIT_DPM + default 0x100000 if HID0_INIT_DPM + +config HID0_INIT_ICE_BIT + hex + default 0x0 if !HID0_INIT_ICE + default 0x8000 if HID0_INIT_ICE + +config HID0_INIT_DCE_BIT + hex + default 0x0 if !HID0_INIT_DCE + default 0x4000 if HID0_INIT_DCE + +config HID0_INIT_ILOCK_BIT + hex + default 0x0 if !HID0_INIT_ILOCK + default 0x2000 if HID0_INIT_ILOCK + +config HID0_INIT_DLOCK_BIT + hex + default 0x0 if !HID0_INIT_DLOCK + default 0x1000 if HID0_INIT_DLOCK + +config HID0_INIT_ICFI_BIT + hex + default 0x0 if !HID0_INIT_ICFI + default 0x800 if HID0_INIT_ICFI + +config HID0_INIT_DCFI_BIT + hex + default 0x0 if !HID0_INIT_DCFI + default 0x400 if HID0_INIT_DCFI + +config HID0_INIT_IFEM_BIT + hex + default 0x0 if !HID0_INIT_IFEM + default 0x80 if HID0_INIT_IFEM + +config HID0_INIT_DECAREN_BIT + hex + default 0x0 if !HID0_INIT_DECAREN + default 0x40 if HID0_INIT_DECAREN + +config HID0_INIT_FBIOB_BIT + hex + default 0x0 if !HID0_INIT_FBIOB + default 0x10 if HID0_INIT_FBIOB + +config HID0_INIT_ABE_BIT + hex + default 0x0 if !HID0_INIT_ABE + default 0x8 if HID0_INIT_ABE + +config HID0_INIT_NOOPTI_BIT + hex + default 0x0 if !HID0_INIT_NOOPTI + default 0x1 if HID0_INIT_NOOPTI + +config HID0_FINAL_EMCP_BIT + hex + default 0x0 if !HID0_FINAL_EMCP + default 0x80000000 if HID0_FINAL_EMCP + +config HID0_FINAL_ECPE_BIT + hex + default 0x0 if !HID0_FINAL_ECPE + default 0x40000000 if HID0_FINAL_ECPE + +config HID0_FINAL_EBA_BIT + hex + default 0x0 if !HID0_FINAL_EBA + default 0x20000000 if HID0_FINAL_EBA + +config HID0_FINAL_EBD_BIT + hex + default 0x0 if !HID0_FINAL_EBD + default 0x10000000 if HID0_FINAL_EBD + +config HID0_FINAL_CLKOUT + hex + default 0x0 if HID0_FINAL_CLKOUT_OFF + default 0x8000000 if HID0_FINAL_CLKOUT_CORE_HALF + default 0x2000000 if HID0_FINAL_CLKOUT_CORE + default 0xa000000 if HID0_FINAL_CLKOUT_BUS + +config HID0_FINAL_SBCLK_BIT + hex + default 0x0 if !HID0_FINAL_SBCLK + default 0x8000000 if HID0_FINAL_SBCLK + +config HID0_FINAL_ECLK_BIT + hex + default 0x0 if !HID0_FINAL_ECLK + default 0x2000000 if HID0_FINAL_ECLK + +config HID0_FINAL_PAR_BIT + hex + default 0x0 if !HID0_FINAL_PAR + default 0x1000000 if HID0_FINAL_PAR + +config HID0_FINAL_DOZE_BIT + hex + default 0x0 if !HID0_FINAL_DOZE + default 0x800000 if HID0_FINAL_DOZE + +config HID0_FINAL_NAP_BIT + hex + default 0x0 if !HID0_FINAL_NAP + default 0x400000 if HID0_FINAL_NAP + +config HID0_FINAL_SLEEP_BIT + hex + default 0x0 if !HID0_FINAL_SLEEP + default 0x200000 if HID0_FINAL_SLEEP + +config HID0_FINAL_DPM_BIT + hex + default 0x0 if !HID0_FINAL_DPM + default 0x100000 if HID0_FINAL_DPM + +config HID0_FINAL_ICE_BIT + hex + default 0x0 if !HID0_FINAL_ICE + default 0x8000 if HID0_FINAL_ICE + +config HID0_FINAL_DCE_BIT + hex + default 0x0 if !HID0_FINAL_DCE + default 0x4000 if HID0_FINAL_DCE + +config HID0_FINAL_ILOCK_BIT + hex + default 0x0 if !HID0_FINAL_ILOCK + default 0x2000 if HID0_FINAL_ILOCK + +config HID0_FINAL_DLOCK_BIT + hex + default 0x0 if !HID0_FINAL_DLOCK + default 0x1000 if HID0_FINAL_DLOCK + +config HID0_FINAL_ICFI_BIT + hex + default 0x0 if !HID0_FINAL_ICFI + default 0x800 if HID0_FINAL_ICFI + +config HID0_FINAL_DCFI_BIT + hex + default 0x0 if !HID0_FINAL_DCFI + default 0x400 if HID0_FINAL_DCFI + +config HID0_FINAL_IFEM_BIT + hex + default 0x0 if !HID0_FINAL_IFEM + default 0x80 if HID0_FINAL_IFEM + +config HID0_FINAL_DECAREN_BIT + hex + default 0x0 if !HID0_FINAL_DECAREN + default 0x40 if HID0_FINAL_DECAREN + +config HID0_FINAL_FBIOB_BIT + hex + default 0x0 if !HID0_FINAL_FBIOB + default 0x10 if HID0_FINAL_FBIOB + +config HID0_FINAL_ABE_BIT + hex + default 0x0 if !HID0_FINAL_ABE + default 0x8 if HID0_FINAL_ABE + +config HID0_FINAL_NOOPTI_BIT + hex + default 0x0 if !HID0_FINAL_NOOPTI + default 0x1 if HID0_FINAL_NOOPTI + +menu "HID2" + +config HID2_LET + bool "True little-endian mode" + +config HID2_IFEB + bool "Instruction fetch burst extension" + +config HID2_MESISTATE + bool "MESI state enable" + +config HID2_IFEC + bool "Instruction fetch cancel extension" + +config HID2_EBQS + bool "BIU queue sharing" + +config HID2_EBPX + bool "BIU pipeline extension" + +if !ARCH_MPC8360 + +config HID2_ELRW + bool "Weighted LRU" + +config HID2_NOKS + bool "No kill for snoop" + +endif + +config HID2_HBE + bool "High bat enable" + +choice + prompt "Instruction cache way-lock" + +config HID2_IWLCK_NONE + bool "No ways locked" + +config HID2_IWLCK_0 + bool "Way 0 locked" + +config HID2_IWLCK_1 + bool "Way 0 through 1 locked" + +config HID2_IWLCK_2 + bool "Way 0 through 2 locked" + +if ARCH_MPC8349 || ARCH_MPC8360 || ARCH_MPC8379 + +config HID2_IWLCK_3 + bool "Way 0 through 3 locked" + +config HID2_IWLCK_4 + bool "Way 0 through 4 locked" + +config HID2_IWLCK_5 + bool "Way 0 through 5 locked" + +config HID2_IWLCK_6 + bool "Way 0 through 6 locked" + +endif + +endchoice + +config HID2_ICWP + bool "Instruction cache way protection" + +choice + prompt "Data cache way-lock" + +config HID2_DWLCK_NONE + bool "No ways locked" + +config HID2_DWLCK_0 + bool "Way 0 locked" + +config HID2_DWLCK_1 + bool "Way 0 through 1 locked" + +config HID2_DWLCK_2 + bool "Way 0 through 2 locked" + +if ARCH_MPC8349 || ARCH_MPC8360 || ARCH_MPC8379 + +config HID2_DWLCK_3 + bool "Way 0 through 3 locked" + +config HID2_DWLCK_4 + bool "Way 0 through 4 locked" + +config HID2_DWLCK_5 + bool "Way 0 through 5 locked" + +config HID2_DWLCK_6 + bool "Way 0 through 6 locked" + +endif + +endchoice + +config HID2_LET_BIT + hex + default 0x0 if !HID2_LET + default 0x8000000 if HID2_LET + +config HID2_IFEB_BIT + hex + default 0x0 if !HID2_IFEB + default 0x4000000 if HID2_IFEB + +config HID2_MESISTATE_BIT + hex + default 0x0 if !HID2_MESISTATE + default 0x1000000 if HID2_MESISTATE + +config HID2_IFEC_BIT + hex + default 0x0 if !HID2_IFEC + default 0x800000 if HID2_IFEC + +config HID2_EBQS_BIT + hex + default 0x0 if !HID2_EBQS + default 0x400000 if HID2_EBQS + +config HID2_EBPX_BIT + hex + default 0x0 if !HID2_EBPX + default 0x200000 if HID2_EBPX + +config HID2_ELRW_BIT + hex + default 0x0 if !HID2_ELRW + default 0x100000 if HID2_ELRW + +config HID2_NOKS_BIT + hex + default 0x0 if !HID2_NOKS + default 0x80000 if HID2_NOKS + +config HID2_HBE_BIT + hex + default 0x0 if !HID2_HBE + default 0x40000 if HID2_HBE + +config HID2_IWLCK + hex + default 0x0 if HID2_IWLCK_NONE + default 0x2000 if HID2_IWLCK_0 + default 0x4000 if HID2_IWLCK_1 + default 0x6000 if HID2_IWLCK_2 + default 0x8000 if HID2_IWLCK_3 + default 0xA000 if HID2_IWLCK_4 + default 0xC000 if HID2_IWLCK_5 + default 0xE000 if HID2_IWLCK_6 + +config HID2_ICWP_BIT + hex + default 0x0 if !HID2_ICWP + default 0x1000 if HID2_ICWP + +config HID2_DWLCK + hex + default 0x0 if HID2_DWLCK_NONE + default 0x20 if HID2_DWLCK_0 + default 0x40 if HID2_DWLCK_1 + default 0x60 if HID2_DWLCK_2 + default 0x80 if HID2_DWLCK_3 + default 0xA0 if HID2_DWLCK_4 + default 0xC0 if HID2_DWLCK_5 + default 0xE0 if HID2_DWLCK_6 + +endmenu + +endmenu diff --git a/arch/powerpc/cpu/mpc83xx/hid/hid.h b/arch/powerpc/cpu/mpc83xx/hid/hid.h new file mode 100644 index 0000000000..9f5260c012 --- /dev/null +++ b/arch/powerpc/cpu/mpc83xx/hid/hid.h @@ -0,0 +1,72 @@ +#define CONFIG_SYS_HID0_FINAL ( \ + CONFIG_HID0_FINAL_ABE_BIT |\ + CONFIG_HID0_FINAL_CLKOUT |\ + CONFIG_HID0_FINAL_DCE_BIT |\ + CONFIG_HID0_FINAL_DCFI_BIT |\ + CONFIG_HID0_FINAL_DECAREN_BIT |\ + CONFIG_HID0_FINAL_DLOCK_BIT |\ + CONFIG_HID0_FINAL_DOZE_BIT |\ + CONFIG_HID0_FINAL_DPM_BIT |\ + CONFIG_HID0_FINAL_EBA_BIT |\ + CONFIG_HID0_FINAL_EBD_BIT |\ + CONFIG_HID0_FINAL_ECLK_BIT |\ + CONFIG_HID0_FINAL_ECPE_BIT |\ + CONFIG_HID0_FINAL_EMCP_BIT |\ + CONFIG_HID0_FINAL_FBIOB_BIT |\ + CONFIG_HID0_FINAL_ICE_BIT |\ + CONFIG_HID0_FINAL_ICFI_BIT |\ + CONFIG_HID0_FINAL_IFEM_BIT |\ + CONFIG_HID0_FINAL_ILOCK_BIT |\ + CONFIG_HID0_FINAL_NAP_BIT |\ + CONFIG_HID0_FINAL_NOOPTI_BIT |\ + CONFIG_HID0_FINAL_PAR_BIT |\ + CONFIG_HID0_FINAL_SBCLK_BIT |\ + CONFIG_HID0_FINAL_SLEEP_BIT \ +) + +#define CONFIG_SYS_HID0_INIT ( \ + CONFIG_HID0_INIT_ABE_BIT |\ + CONFIG_HID0_INIT_CLKOUT |\ + CONFIG_HID0_INIT_DCE_BIT |\ + CONFIG_HID0_INIT_DCFI_BIT |\ + CONFIG_HID0_INIT_DECAREN_BIT |\ + CONFIG_HID0_INIT_DLOCK_BIT |\ + CONFIG_HID0_INIT_DOZE_BIT |\ + CONFIG_HID0_INIT_DPM_BIT |\ + CONFIG_HID0_INIT_EBA_BIT |\ + CONFIG_HID0_INIT_EBD_BIT |\ + CONFIG_HID0_INIT_ECPE_BIT |\ + CONFIG_HID0_INIT_EMCP_BIT |\ + CONFIG_HID0_INIT_FBIOB_BIT |\ + CONFIG_HID0_INIT_ICE_BIT |\ + CONFIG_HID0_INIT_ICFI_BIT |\ + CONFIG_HID0_INIT_IFEM_BIT |\ + CONFIG_HID0_INIT_ILOCK_BIT |\ + CONFIG_HID0_INIT_NAP_BIT |\ + CONFIG_HID0_INIT_NOOPTI_BIT |\ + CONFIG_HID0_INIT_PAR_BIT |\ + CONFIG_HID0_INIT_SLEEP_BIT \ +) + +#ifdef CONFIG_TARGET_IDS8313 +/* IDS8313 defines a reserved bit; keep to not break compatibility */ +#define CONFIG_HID2_SPECIAL 0x00020000 +#else +#define CONFIG_HID2_SPECIAL 0x0 +#endif + +#define CONFIG_SYS_HID2 ( \ + CONFIG_HID2_LET_BIT |\ + CONFIG_HID2_IFEB_BIT |\ + CONFIG_HID2_MESISTATE_BIT |\ + CONFIG_HID2_IFEC_BIT |\ + CONFIG_HID2_EBQS_BIT |\ + CONFIG_HID2_EBPX_BIT |\ + CONFIG_HID2_ELRW_BIT |\ + CONFIG_HID2_NOKS_BIT |\ + CONFIG_HID2_HBE_BIT |\ + CONFIG_HID2_IWLCK |\ + CONFIG_HID2_ICWP_BIT |\ + CONFIG_HID2_DWLCK |\ + CONFIG_HID2_SPECIAL \ +) diff --git a/arch/powerpc/cpu/mpc83xx/hrcw/Kconfig b/arch/powerpc/cpu/mpc83xx/hrcw/Kconfig new file mode 100644 index 0000000000..c657a47b11 --- /dev/null +++ b/arch/powerpc/cpu/mpc83xx/hrcw/Kconfig @@ -0,0 +1,816 @@ +menu "Reset Configuration Word" + +choice + prompt "Local bus memory controller clock mode" + +config LBMC_CLOCK_MODE_1_1 + bool "1 : 1" + +config LBMC_CLOCK_MODE_1_2 + depends on ARCH_MPC8349 || ARCH_MPC8360 || ARCH_MPC837X + bool "1 : 2" + +endchoice + +choice + prompt "DDR SDRAM memory controller clock mode" + +config DDR_MC_CLOCK_MODE_1_2 + bool "1 : 2" + +config DDR_MC_CLOCK_MODE_1_1 + depends on ARCH_MPC8315 || ARCH_MPC8349 || ARCH_MPC8360 || ARCH_MPC837X + bool "1 : 1" + +endchoice + +if !ARCH_MPC8313 && !ARCH_MPC832X && !ARCH_MPC8349 + +choice + prompt "System PLL VCO division" + +config SYSTEM_PLL_VCO_DIV_1 + depends on !ARCH_MPC837X + bool "1" + +config SYSTEM_PLL_VCO_DIV_2 + bool "2" + +config SYSTEM_PLL_VCO_DIV_4 + depends on !ARCH_MPC831X + bool "4" + +config SYSTEM_PLL_VCO_DIV_8 + depends on !ARCH_MPC831X + bool "8" + +endchoice + +endif + +choice + prompt "System PLL multiplication factor" + +config SYSTEM_PLL_FACTOR_2_1 + bool "2 : 1" + +config SYSTEM_PLL_FACTOR_3_1 + bool "3 : 1" + +config SYSTEM_PLL_FACTOR_4_1 + bool "4 : 1" + +config SYSTEM_PLL_FACTOR_5_1 + bool "5 : 1" + +config SYSTEM_PLL_FACTOR_6_1 + bool "6 : 1" + +config SYSTEM_PLL_FACTOR_7_1 + depends on ARCH_MPC8349 || ARCH_MPV8360 || ARCH_MPC837X + bool "7 : 1" + +config SYSTEM_PLL_FACTOR_8_1 + depends on ARCH_MPC8349 || ARCH_MPV8360 || ARCH_MPC837X + bool "8 : 1" + +config SYSTEM_PLL_FACTOR_9_1 + depends on ARCH_MPC8349 || ARCH_MPV8360 || ARCH_MPC837X + bool "9 : 1" + +config SYSTEM_PLL_FACTOR_10_1 + depends on ARCH_MPC8349 || ARCH_MPV8360 || ARCH_MPC837X + bool "10 : 1" + +config SYSTEM_PLL_FACTOR_11_1 + depends on ARCH_MPC8349 || ARCH_MPV8360 || ARCH_MPC837X + bool "11 : 1" + +config SYSTEM_PLL_FACTOR_12_1 + depends on ARCH_MPC8349 || ARCH_MPV8360 || ARCH_MPC837X + bool "12 : 1" + +config SYSTEM_PLL_FACTOR_13_1 + depends on ARCH_MPC8349 || ARCH_MPV8360 || ARCH_MPC837X + bool "13 : 1" + +config SYSTEM_PLL_FACTOR_14_1 + depends on ARCH_MPC8349 || ARCH_MPV8360 || ARCH_MPC837X + bool "14 : 1" + +config SYSTEM_PLL_FACTOR_15_1 + depends on ARCH_MPC8349 || ARCH_MPV8360 || ARCH_MPC837X + bool "15 : 1" + +config SYSTEM_PLL_FACTOR_16_1 + depends on ARCH_MPC8349 || ARCH_MPV8360 + bool "16 : 1" + +endchoice + +config CORE_PLL_BYPASS + bool "Core PLL bypassed" + +if !CORE_PLL_BYPASS + +choice + prompt "Core PLL Ratio" + +config CORE_PLL_RATIO_1_1 + bool "1 : 1" + +config CORE_PLL_RATIO_15_1 + bool "1.5 : 1" + +config CORE_PLL_RATIO_2_1 + bool "2 : 1" + +config CORE_PLL_RATIO_25_1 + bool "2.5 : 1" + +config CORE_PLL_RATIO_3_1 + bool "3 : 1" + +endchoice + +choice + prompt "Core PLL VCO Divider" + +config CORE_PLL_VCO_DIVIDER_2 + bool "2" + +config CORE_PLL_VCO_DIVIDER_4 + bool "4" + +config CORE_PLL_VCO_DIVIDER_8 + depends on !ARCH_MPC8315 + bool "8" + +endchoice + +endif + +if MPC83XX_QUICC_ENGINE + +choice + prompt "QUICC Engine PLL VCO Divider" + +config QUICC_VCO_DIVIDER_2 + bool "2" + +config QUICC_VCO_DIVIDER_4 + bool "4" + +config QUICC_VCO_DIVIDER_8 + depends on ARCH_MPC8309 + bool "8" + +endchoice + +choice + prompt "QUICC Engine PLL division factor" + +config QUICC_DIV_FACTOR_1 + bool "1" + +config QUICC_DIV_FACTOR_2 + bool "2" + +endchoice + +choice + prompt "QUICC Engine PLL multiplication factor" + +config QUICC_MULT_FACTOR_2 + bool "2" + +config QUICC_MULT_FACTOR_3 + bool "3" + +config QUICC_MULT_FACTOR_4 + bool "4" + +config QUICC_MULT_FACTOR_5 + bool "5" + +config QUICC_MULT_FACTOR_6 + bool "6" + +config QUICC_MULT_FACTOR_7 + bool "7" + +config QUICC_MULT_FACTOR_8 + bool "8" + +config QUICC_MULT_FACTOR_9 + depends on ARCH_MPC8360 + bool "9" + +config QUICC_MULT_FACTOR_10 + depends on ARCH_MPC8360 + bool "10" + +config QUICC_MULT_FACTOR_11 + depends on ARCH_MPC8360 + bool "11" + +config QUICC_MULT_FACTOR_12 + depends on ARCH_MPC8360 + bool "12" + +config QUICC_MULT_FACTOR_13 + depends on ARCH_MPC8360 + bool "13" + +config QUICC_MULT_FACTOR_14 + depends on ARCH_MPC8360 + bool "14" + +config QUICC_MULT_FACTOR_15 + depends on ARCH_MPC8360 + bool "15" + +config QUICC_MULT_FACTOR_16 + depends on ARCH_MPC8360 + bool "16" + +config QUICC_MULT_FACTOR_17 + depends on ARCH_MPC8360 + bool "17" + +config QUICC_MULT_FACTOR_18 + depends on ARCH_MPC8360 + bool "18" + +config QUICC_MULT_FACTOR_19 + depends on ARCH_MPC8360 + bool "19" + +config QUICC_MULT_FACTOR_20 + depends on ARCH_MPC8360 + bool "20" + +config QUICC_MULT_FACTOR_21 + depends on ARCH_MPC8360 + bool "21" + +config QUICC_MULT_FACTOR_22 + depends on ARCH_MPC8360 + bool "22" + +config QUICC_MULT_FACTOR_23 + depends on ARCH_MPC8360 + bool "23" + +config QUICC_MULT_FACTOR_24 + depends on ARCH_MPC8360 + bool "24" + +config QUICC_MULT_FACTOR_25 + depends on ARCH_MPC8360 + bool "25" + +config QUICC_MULT_FACTOR_26 + depends on ARCH_MPC8360 + bool "26" + +config QUICC_MULT_FACTOR_27 + depends on ARCH_MPC8360 + bool "27" + +config QUICC_MULT_FACTOR_28 + depends on ARCH_MPC8360 + bool "28" + +config QUICC_MULT_FACTOR_29 + depends on ARCH_MPC8360 + bool "29" + +config QUICC_MULT_FACTOR_30 + depends on ARCH_MPC8360 + bool "30" + +config QUICC_MULT_FACTOR_31 + depends on ARCH_MPC8360 + bool "31" + +endchoice + +endif + +if MPC83XX_PCI_SUPPORT + +choice + prompt "PCI host mode" + +config PCI_HOST_MODE_DISABLE + bool "Disabled" + +config PCI_HOST_MODE_ENABLE + bool "Enabled" + +endchoice + +if ARCH_MPC8349 + +choice + prompt "PCI 64-bit mode" + +config PCI_64BIT_MODE_DISABLE + bool "Disabled" + +config PCI_64BIT_MODE_ENABLE + bool "Enabled" + +endchoice + +endif + +choice + prompt "PCI internal arbiter 1 mode" + +config PCI_INT_ARBITER1_DISABLE + bool "Disabled" + +config PCI_INT_ARBITER1_ENABLE + bool "Enabled" + +endchoice + +if ARCH_MPC8349 + +choice + prompt "PCI internal arbiter 2 mode" + +config PCI_INT_ARBITER2_DISABLE + bool "Disabled" + +config PCI_INT_ARBITER2_ENABLE + bool "Enabled" + +endchoice + +endif + +if ARCH_MPC8360 + +choice + prompt "PCI clock output drive" + +config PCI_CLOCK_OUTPUT_DRIVE_DISABLE + bool "Disabled" + +config PCI_CLOCK_OUTPUT_DRIVE_ENABLE + bool "Enabled" + +endchoice + +endif + +endif + +choice + prompt "Core disable mode" + +config CORE_DISABLE_MODE_OFF + bool "Off" + +config CORE_DISABLE_MODE_ON + bool "On" + +endchoice + +choice + prompt "Boot Memory Space" + +config BOOT_MEMORY_SPACE_HIGH + bool "High" + +config BOOT_MEMORY_SPACE_LOW + bool "Low" + +endchoice + +choice + prompt "Boot Sequencer Configuration" + +config BOOT_SEQUENCER_DISABLED + bool "Disabled" + +config BOOT_SEQUENCER_NORMAL_I2C + bool "Normal I2C" + +config BOOT_SEQUENCER_EXTENDED_I2C + bool "Extended I2C" + +endchoice + +choice + prompt "Software Watchdog" + +config SOFTWARE_WATCHDOG_DISABLED + bool "Disabled" + +config SOFTWARE_WATCHDOG_ENABLED + bool "Enabled" + +endchoice + +choice + prompt "Boot ROM interface location" + +config BOOT_ROM_INTERFACE_DDR_SDRAM + bool "DDR_SDRAM" + +config BOOT_ROM_INTERFACE_PCI1 + depends on MPC83XX_PCI_SUPPORT + bool "PCI1" + +config BOOT_ROM_INTERFACE_PCI2 + depends on MPC83XX_PCI_SUPPORT && ARCH_MPC8349 + bool "PCI2" + +config BOOT_ROM_INTERFACE_ON_CHIP_BOOT_ROM + depends on ARCH_MPC837X + bool "PCI2" + +config BOOT_ROM_INTERFACE_ESDHC + depends on ARCH_MPC8309 + bool "eSDHC" + +config BOOT_ROM_INTERFACE_SPI + depends on ARCH_MPC8309 + bool "SPI" + +config BOOT_ROM_INTERFACE_GPCM_8BIT + bool "Local bus GPCM - 8-bit ROM" + +config BOOT_ROM_INTERFACE_GPCM_16BIT + bool "Local bus GPCM - 16-bit ROM" + +config BOOT_ROM_INTERFACE_GPCM_32BIT + depends on ARCH_MPC8349 || ARCH_MPC8360 || ARCH_MPC837X + bool "Local bus GPCM - 32-bit ROM" + +config BOOT_ROM_INTERFACE_NAND_FLASH_8BIT_SMALL + depends on !ARCH_MPC832X && !ARCH_MPC8349 && !ARCH_MPC8360 + bool "Local bus NAND Flash- 8-bit small page ROM" + +config BOOT_ROM_INTERFACE_NAND_FLASH_8BIT_LARGE + depends on !ARCH_MPC832X && !ARCH_MPC8349 && !ARCH_MPC8360 + bool "Local bus NAND Flash- 8-bit large page ROM" + +endchoice + +if MPC83XX_TSEC1_SUPPORT + +choice + prompt "TSEC1 mode" + +config TSEC1_MODE_MII + depends on !ARCH_MPC8349 + bool "MII" + +config TSEC1_MODE_RMII + depends on ARCH_MPC831X && !ARCH_MPC8349 + bool "RMII" + +config TSEC1_MODE_RGMII + bool "RGMII" + +config TSEC1_MODE_RTBI + depends on ARCH_MPC831X || ARCH_MPC837X + bool "RTBI" + +config TSEC1_MODE_GMII + depends on ARCH_MPC8349 + bool "GMII" + +config TSEC1_MODE_TBI + depends on ARCH_MPC8349 + bool "TBI" + +config TSEC1_MODE_SGMII + depends on ARCH_MPC831X || ARCH_MPC837X + bool "SGMII" + +endchoice + +endif + +if MPC83XX_TSEC2_SUPPORT + +choice + prompt "TSEC2 mode" + +config TSEC2_MODE_MII + depends on !ARCH_MPC8349 + bool "MII" + +config TSEC2_MODE_RMII + depends on ARCH_MPC831X && !ARCH_MPC8349 + bool "RMII" + +config TSEC2_MODE_RGMII + bool "RGMII" + +config TSEC2_MODE_RTBI + depends on ARCH_MPC831X || ARCH_MPC837X + bool "RTBI" + +config TSEC2_MODE_GMII + depends on ARCH_MPC8349 + bool "GMII" + +config TSEC2_MODE_TBI + depends on ARCH_MPC8349 + bool "TBI" + +config TSEC2_MODE_SGMII + depends on ARCH_MPC831X || ARCH_MPC837X + bool "SGMII" + +endchoice + +endif + +choice + prompt "True litle-endian mode" + +config TRUE_LITTLE_ENDIAN_BIG_ENDIAN + bool "Big-endian" + +config TRUE_LITTLE_ENDIAN_LITTLE_ENDIAN + bool "Little-endian" + +endchoice + +if ARCH_MPC8360 + +choice + prompt "Secondary DDR IO" + +config SECONDARY_DDR_IO_DISABLE + bool "Disable" + +config SECONDARY_DDR_IO_ENABLE + bool "Enable" + +endchoice + +endif + +if ARCH_MPC831X || ARCH_MPC832X || ARCH_MPC8349 || ARCH_MPC8360 + +choice + prompt "LALE timing" + +config LALE_TIMING_NORMAL + bool "Normal" + +config LALE_TIMING_EARLIER + bool "Earlier" + +endchoice + +endif + +if MPC83XX_LDP_PIN + +choice + prompt "LDP pin mux state" + +config LDP_PIN_MUX_STATE_1 + bool "Inital value 1" + +config LDP_PIN_MUX_STATE_0 + bool "Inital value 0" + +endchoice + +endif + +endmenu + +config LBMC_CLOCK_MODE + int + default 0 if LBMC_CLOCK_MODE_1_1 + default 1 if LBMC_CLOCK_MODE_1_2 + +config DDR_MC_CLOCK_MODE + int + default 1 if DDR_MC_CLOCK_MODE_1_2 + default 0 if DDR_MC_CLOCK_MODE_1_1 + +config SYSTEM_PLL_VCO_DIV + int + default 0 if ARCH_MPC8349 || ARCH_MPC832X + default 2 if ARCH_MPC8313 + default 0 if SYSTEM_PLL_VCO_DIV_2 && !ARCH_MPC8360 && !ARCH_MPC837X + default 1 if SYSTEM_PLL_VCO_DIV_4 && !ARCH_MPC8360 && !ARCH_MPC837X + default 2 if SYSTEM_PLL_VCO_DIV_8 && !ARCH_MPC8360 && !ARCH_MPC837X + default 0 if SYSTEM_PLL_VCO_DIV_4 && (ARCH_MPC8360 || ARCH_MPC837X) + default 1 if SYSTEM_PLL_VCO_DIV_8 && (ARCH_MPC8360 || ARCH_MPC837X) + default 2 if SYSTEM_PLL_VCO_DIV_2 && (ARCH_MPC8360 || ARCH_MPC837X) + default 3 if SYSTEM_PLL_VCO_DIV_1 + +config SYSTEM_PLL_FACTOR + int + default 2 if SYSTEM_PLL_FACTOR_2_1 + default 3 if SYSTEM_PLL_FACTOR_3_1 + default 4 if SYSTEM_PLL_FACTOR_4_1 + default 5 if SYSTEM_PLL_FACTOR_5_1 + default 6 if SYSTEM_PLL_FACTOR_6_1 + default 7 if SYSTEM_PLL_FACTOR_7_1 + default 8 if SYSTEM_PLL_FACTOR_8_1 + default 9 if SYSTEM_PLL_FACTOR_9_1 + default 10 if SYSTEM_PLL_FACTOR_10_1 + default 11 if SYSTEM_PLL_FACTOR_11_1 + default 12 if SYSTEM_PLL_FACTOR_12_1 + default 13 if SYSTEM_PLL_FACTOR_13_1 + default 14 if SYSTEM_PLL_FACTOR_14_1 + default 15 if SYSTEM_PLL_FACTOR_15_1 + default 0 if SYSTEM_PLL_FACTOR_16_1 + +config CORE_PLL_RATIO + hex + default 0x0 if CORE_PLL_BYPASS + default 0x02 if CORE_PLL_RATIO_1_1 && CORE_PLL_VCO_DIVIDER_2 + default 0x22 if CORE_PLL_RATIO_1_1 && CORE_PLL_VCO_DIVIDER_4 + default 0x42 if CORE_PLL_RATIO_1_1 && CORE_PLL_VCO_DIVIDER_8 + default 0x03 if CORE_PLL_RATIO_15_1 && CORE_PLL_VCO_DIVIDER_2 + default 0x23 if CORE_PLL_RATIO_15_1 && CORE_PLL_VCO_DIVIDER_4 + default 0x43 if CORE_PLL_RATIO_15_1 && CORE_PLL_VCO_DIVIDER_8 + default 0x04 if CORE_PLL_RATIO_2_1 && CORE_PLL_VCO_DIVIDER_2 + default 0x24 if CORE_PLL_RATIO_2_1 && CORE_PLL_VCO_DIVIDER_4 + default 0x44 if CORE_PLL_RATIO_2_1 && CORE_PLL_VCO_DIVIDER_8 + default 0x05 if CORE_PLL_RATIO_25_1 && CORE_PLL_VCO_DIVIDER_2 + default 0x25 if CORE_PLL_RATIO_25_1 && CORE_PLL_VCO_DIVIDER_4 + default 0x45 if CORE_PLL_RATIO_25_1 && CORE_PLL_VCO_DIVIDER_8 + default 0x06 if CORE_PLL_RATIO_3_1 && CORE_PLL_VCO_DIVIDER_2 + default 0x26 if CORE_PLL_RATIO_3_1 && CORE_PLL_VCO_DIVIDER_4 + default 0x46 if CORE_PLL_RATIO_3_1 && CORE_PLL_VCO_DIVIDER_8 + +config CORE_DISABLE_MODE + int + default 0 if CORE_DISABLE_MODE_OFF + default 1 if CORE_DISABLE_MODE_ON + +config BOOT_MEMORY_SPACE + int + default 0 if BOOT_MEMORY_SPACE_LOW + default 1 if BOOT_MEMORY_SPACE_HIGH + +config BOOT_SEQUENCER + int + default 0 if BOOT_SEQUENCER_DISABLED + default 1 if BOOT_SEQUENCER_NORMAL_I2C + default 2 if BOOT_SEQUENCER_EXTENDED_I2C + +config SOFTWARE_WATCHDOG + int + default 0 if SOFTWARE_WATCHDOG_DISABLED + default 1 if SOFTWARE_WATCHDOG_ENABLED + +config BOOT_ROM_INTERFACE + hex + default 0x0 if BOOT_ROM_INTERFACE_DDR_SDRAM + default 0x4 if BOOT_ROM_INTERFACE_PCI1 + default 0x8 if BOOT_ROM_INTERFACE_PCI2 + default 0x8 if BOOT_ROM_INTERFACE_ESDHC + default 0xc if BOOT_ROM_INTERFACE_SPI + default 0xc if BOOT_ROM_INTERFACE_ON_CHIP_BOOT_ROM + default 0x14 if BOOT_ROM_INTERFACE_GPCM_8BIT + default 0x18 if BOOT_ROM_INTERFACE_GPCM_16BIT + default 0x1c if BOOT_ROM_INTERFACE_GPCM_32BIT + default 0x5 if BOOT_ROM_INTERFACE_NAND_FLASH_8BIT_SMALL + default 0x15 if BOOT_ROM_INTERFACE_NAND_FLASH_8BIT_LARGE + +config TSEC1_MODE + hex + default 0x0 if !MPC83XX_TSEC1_SUPPORT + default 0x0 if TSEC1_MODE_MII + default 0x1 if TSEC1_MODE_RMII + default 0x3 if TSEC1_MODE_RGMII && !ARCH_MPC8349 + default 0x5 if TSEC1_MODE_RTBI && !ARCH_MPC8349 + default 0x6 if TSEC1_MODE_SGMII + default 0x0 if TSEC1_MODE_RGMII && ARCH_MPC8349 + default 0x1 if TSEC1_MODE_RTBI && ARCH_MPC8349 + default 0x2 if TSEC1_MODE_GMII + default 0x3 if TSEC1_MODE_TBI + +config TSEC2_MODE + hex + default 0x0 if !MPC83XX_TSEC2_SUPPORT + default 0x0 if TSEC2_MODE_MII + default 0x1 if TSEC2_MODE_RMII + default 0x3 if TSEC2_MODE_RGMII && !ARCH_MPC8349 + default 0x5 if TSEC2_MODE_RTBI && !ARCH_MPC8349 + default 0x6 if TSEC2_MODE_SGMII + default 0x0 if TSEC2_MODE_RGMII && ARCH_MPC8349 + default 0x1 if TSEC2_MODE_RTBI && ARCH_MPC8349 + default 0x2 if TSEC2_MODE_GMII + default 0x3 if TSEC2_MODE_TBI + +config SECONDARY_DDR_IO + int + default 0 if !ARCH_MPC8360 + default 0 if SECONDARY_DDR_IO_DISABLE + default 1 if SECONDARY_DDR_IO_ENABLE + +config TRUE_LITTLE_ENDIAN + int + default 0 if TRUE_LITTLE_ENDIAN_BIG_ENDIAN + default 1 if TRUE_LITTLE_ENDIAN_LITTLE_ENDIAN + +config LALE_TIMING + int + default 0 if ARCH_MPC830X || ARCH_MPC837X + default 0 if LALE_TIMING_NORMAL + default 1 if LALE_TIMING_EARLIER + +config LDP_PIN_MUX_STATE + int + default 0 if !MPC83XX_LDP_PIN + default 0 if LDP_PIN_MUX_STATE_1 + default 1 if LDP_PIN_MUX_STATE_0 + +config QUICC_VCO_DIVIDER + int + default 0 if !MPC83XX_QUICC_ENGINE + default 0 if QUICC_VCO_DIVIDER_2 && ARCH_MPC8309 + default 1 if QUICC_VCO_DIVIDER_4 && ARCH_MPC8309 + default 2 if QUICC_VCO_DIVIDER_8 && ARCH_MPC8309 + default 2 if QUICC_VCO_DIVIDER_2 && (ARCH_MPC832X || ARCH_MPC8360) + default 0 if QUICC_VCO_DIVIDER_4 && (ARCH_MPC832X || ARCH_MPC8360) + default 1 if QUICC_VCO_DIVIDER_8 && ARCH_MPC8360 + +config QUICC_DIV_FACTOR + int + default 0 if !MPC83XX_QUICC_ENGINE + default 0 if QUICC_DIV_FACTOR_1 + default 1 if QUICC_DIV_FACTOR_2 + +config QUICC_MULT_FACTOR + int + default 0 if !MPC83XX_QUICC_ENGINE + default 2 if QUICC_MULT_FACTOR_2 + default 3 if QUICC_MULT_FACTOR_3 + default 4 if QUICC_MULT_FACTOR_4 + default 5 if QUICC_MULT_FACTOR_5 + default 6 if QUICC_MULT_FACTOR_6 + default 7 if QUICC_MULT_FACTOR_7 + default 8 if QUICC_MULT_FACTOR_8 + default 9 if QUICC_MULT_FACTOR_9 + default 10 if QUICC_MULT_FACTOR_10 + default 11 if QUICC_MULT_FACTOR_11 + default 12 if QUICC_MULT_FACTOR_12 + default 13 if QUICC_MULT_FACTOR_13 + default 14 if QUICC_MULT_FACTOR_14 + default 15 if QUICC_MULT_FACTOR_15 + default 16 if QUICC_MULT_FACTOR_16 + default 17 if QUICC_MULT_FACTOR_17 + default 18 if QUICC_MULT_FACTOR_18 + default 19 if QUICC_MULT_FACTOR_19 + default 20 if QUICC_MULT_FACTOR_20 + default 21 if QUICC_MULT_FACTOR_21 + default 22 if QUICC_MULT_FACTOR_22 + default 23 if QUICC_MULT_FACTOR_23 + default 24 if QUICC_MULT_FACTOR_24 + default 25 if QUICC_MULT_FACTOR_25 + default 26 if QUICC_MULT_FACTOR_26 + default 27 if QUICC_MULT_FACTOR_27 + default 28 if QUICC_MULT_FACTOR_28 + default 29 if QUICC_MULT_FACTOR_29 + default 30 if QUICC_MULT_FACTOR_30 + default 31 if QUICC_MULT_FACTOR_31 + +config PCI_HOST_MODE + int + default 0 if !MPC83XX_PCI_SUPPORT && !ARCH_MPC8308 + default 0 if PCI_HOST_MODE_DISABLE + default 1 if PCI_HOST_MODE_ENABLE || ARCH_MPC8308 # MPC8308 needs this bit set regardless + +config PCI_64BIT_MODE + int + default 0 if !ARCH_MPC8349 + default 0 if PCI_64BIT_MODE_DISABLE + default 1 if PCI_64BIT_MODE_ENABLE + +config PCI_INT_ARBITER1 + int + default 0 if !MPC83XX_PCI_SUPPORT && !ARCH_MPC8308 + default 0 if PCI_INT_ARBITER1_DISABLE + default 1 if PCI_INT_ARBITER1_ENABLE || ARCH_MPC8308 # MPC8308 needs this bit set regardless + +config PCI_INT_ARBITER2 + int + default 0 if !ARCH_MPC8349 + default 0 if PCI_INT_ARBITER2_DISABLE + default 1 if PCI_INT_ARBITER2_ENABLE + +config PCI_CLOCK_OUTPUT_DRIVE + int + default 0 if !ARCH_MPC8360 + default 0 if PCI_CLOCK_OUTPUT_DRIVE_DISABLE + default 1 if PCI_CLOCK_OUTPUT_DRIVE_ENABLE diff --git a/arch/powerpc/cpu/mpc83xx/hrcw/hrcw.h b/arch/powerpc/cpu/mpc83xx/hrcw/hrcw.h new file mode 100644 index 0000000000..7d66ba726b --- /dev/null +++ b/arch/powerpc/cpu/mpc83xx/hrcw/hrcw.h @@ -0,0 +1,37 @@ +#ifdef CONFIG_ARCH_MPC8349 +#define TSEC1_MODE_SHIFT 17 +#define TSEC2_MODE_SHIFT 19 +#else +#define TSEC1_MODE_SHIFT 18 +#define TSEC2_MODE_SHIFT 21 +#endif + +#define CONFIG_SYS_HRCW_LOW (\ + (CONFIG_LBMC_CLOCK_MODE << (31 - 0)) |\ + (CONFIG_DDR_MC_CLOCK_MODE << (31 - 1)) |\ + (CONFIG_SYSTEM_PLL_VCO_DIV << (31 - 3)) |\ + (CONFIG_SYSTEM_PLL_FACTOR << (31 - 7)) |\ + (CONFIG_CORE_PLL_RATIO << (31 - 15)) |\ + (CONFIG_QUICC_VCO_DIVIDER << (31 - 25)) |\ + (CONFIG_QUICC_DIV_FACTOR << (31 - 26)) |\ + (CONFIG_QUICC_MULT_FACTOR << (31 - 31)) \ + ) + +#define CONFIG_SYS_HRCW_HIGH (\ + (CONFIG_PCI_HOST_MODE << (31 - 0)) |\ + (CONFIG_PCI_64BIT_MODE << (31 - 1)) |\ + (CONFIG_PCI_INT_ARBITER1 << (31 - 2)) |\ + (CONFIG_PCI_INT_ARBITER2 << (31 - 3)) |\ + (CONFIG_PCI_CLOCK_OUTPUT_DRIVE << (31 - 3)) |\ + (CONFIG_CORE_DISABLE_MODE << (31 - 4)) |\ + (CONFIG_BOOT_MEMORY_SPACE << (31 - 5)) |\ + (CONFIG_BOOT_SEQUENCER << (31 - 7)) |\ + (CONFIG_SOFTWARE_WATCHDOG << (31 - 8)) |\ + (CONFIG_BOOT_ROM_INTERFACE << (31 - 13)) |\ + (CONFIG_TSEC1_MODE << (31 - TSEC1_MODE_SHIFT)) |\ + (CONFIG_TSEC2_MODE << (31 - TSEC2_MODE_SHIFT)) |\ + (CONFIG_SECONDARY_DDR_IO << (31 - 27)) |\ + (CONFIG_TRUE_LITTLE_ENDIAN << (31 - 28)) |\ + (CONFIG_LALE_TIMING << (31 - 29)) |\ + (CONFIG_LDP_PIN_MUX_STATE << (31 - 30)) \ + ) diff --git a/arch/powerpc/cpu/mpc83xx/initreg/Kconfig b/arch/powerpc/cpu/mpc83xx/initreg/Kconfig new file mode 100644 index 0000000000..a6b42a29af --- /dev/null +++ b/arch/powerpc/cpu/mpc83xx/initreg/Kconfig @@ -0,0 +1,6 @@ +menu "Initial register configuration" + +source "arch/powerpc/cpu/mpc83xx/initreg/Kconfig.spcr" +source "arch/powerpc/cpu/mpc83xx/initreg/Kconfig.lcrr" + +endmenu diff --git a/arch/powerpc/cpu/mpc83xx/initreg/Kconfig.lcrr b/arch/powerpc/cpu/mpc83xx/initreg/Kconfig.lcrr new file mode 100644 index 0000000000..e6b6130de2 --- /dev/null +++ b/arch/powerpc/cpu/mpc83xx/initreg/Kconfig.lcrr @@ -0,0 +1,139 @@ +menu "LCRR - Clock Ratio Register register" + +if !ARCH_MPC8309 && !ARCH_MPC831X && !ARCH_MPC832X + +choice + prompt "DLL bypass" + +config LCRR_DBYP_UNSET + bool "Don't set value" + +config LCRR_DBYP_PLL_ENABLED + bool "PLL enabled" + +config LCRR_DBYP_PLL_BYPASSED + bool "PLL bypassed" + +endchoice + +endif + +if ARCH_MPC834X || ARCH_MPC8360 + +choice + prompt "Additional delay cycles for SDRAM control signals" + +config LCRR_BUFCMDC_UNSET + bool "Don't set value" + +config LCRR_BUFCMDC_4 + bool "4" + +config LCRR_BUFCMDC_1 + bool "1" + +config LCRR_BUFCMDC_2 + bool "2" + +config LCRR_BUFCMDC_3 + bool "3" + +endchoice + +choice + prompt "Extended CAS latency" + +config LCRR_ECL_UNSET + bool "Don't set value" + +config LCRR_ECL_4 + bool "4" + +config LCRR_ECL_5 + bool "5" + +config LCRR_ECL_6 + bool "6" + +config LCRR_ECL_7 + bool "7" + +endchoice + +endif # ARCH_MPC834X || ARCH_MPC8360 + +if !ARCH_MPC8308 + +choice + prompt "External address delay cycles" + +config LCRR_EADC_UNSET + bool "Don't set value" + +config LCRR_EADC_4 + bool "4" + +config LCRR_EADC_1 + bool "1" + +config LCRR_EADC_2 + bool "2" + +config LCRR_EADC_3 + bool "3" + +endchoice + +endif # !ARCH_MPC8308 + +choice + prompt "System clock divider" + +config LCRR_CLKDIV_UNSET + bool "Don't set value" + +config LCRR_CLKDIV_2 + bool "2" + +config LCRR_CLKDIV_4 + bool "4" + +config LCRR_CLKDIV_8 + bool "8" + +endchoice + +config LCRR_DBYP + hex + default 0x0 if LCRR_DBYP_UNSET || LCRR_DBYP_PLL_ENABLED + default 0x80000000 if LCRR_DBYP_PLL_BYPASSED + +config LCRR_BUFCMDC + hex + default 0x0 if LCRR_BUFCMDC_4 || LCRR_BUFCMDC_UNSET + default 0x10000000 if LCRR_BUFCMDC_1 + default 0x20000000 if LCRR_BUFCMDC_2 + default 0x30000000 if LCRR_BUFCMDC_3 + +config LCRR_ECL + hex + default 0x0 if LCRR_ECL_4 || LCRR_ECL_UNSET + default 0x1000000 if LCRR_ECL_5 + default 0x2000000 if LCRR_ECL_6 + default 0x3000000 if LCRR_ECL_7 + +config LCRR_EADC + hex + default 0x0 if LCRR_EADC_4 || LCRR_EADC_UNSET + default 0x10000 if LCRR_EADC_1 + default 0x20000 if LCRR_EADC_2 + default 0x30000 if LCRR_EADC_3 + +config LCRR_CLKDIV + hex + default 0x0 if LCRR_CLKDIV_UNSET + default 0x2 if LCRR_CLKDIV_2 + default 0x4 if LCRR_CLKDIV_4 + default 0x8 if LCRR_CLKDIV_8 + +endmenu diff --git a/arch/powerpc/cpu/mpc83xx/initreg/Kconfig.spcr b/arch/powerpc/cpu/mpc83xx/initreg/Kconfig.spcr new file mode 100644 index 0000000000..f32309e6c0 --- /dev/null +++ b/arch/powerpc/cpu/mpc83xx/initreg/Kconfig.spcr @@ -0,0 +1,115 @@ +menu "SPCR - System priority and configuration register" + +choice + prompt "Optimize" + +config SPCR_OPT_UNSET + bool "Don't set value" + +config SPCR_OPT_NONE + bool "No performance enhancement" + +config SPCR_OPT_SPEC_READ + bool "Performance enhancement by speculative read" + +endchoice + +if ARCH_MPC8308 || ARCH_MPC831X || ARCH_MPC837X + +choice + prompt "TSEC emergency priority" + +config SPCR_TSECEP_UNSET + bool "Don't set value" + +config SPCR_TSECEP_0 + bool "Level 0 (lowest priority)" + +config SPCR_TSECEP_1 + bool "Level 1" + +config SPCR_TSECEP_2 + bool "Level 2" + +config SPCR_TSECEP_3 + bool "Level 3 (highest priority)" + +endchoice + +endif + +if ARCH_MPC8349 + +choice + prompt "TSEC1 emergency priority" + +config SPCR_TSEC1EP_UNSET + bool "Don't set value" + +config SPCR_TSEC1EP_0 + bool "Level 0 (lowest priority)" + +config SPCR_TSEC1EP_1 + bool "Level 1" + +config SPCR_TSEC1EP_2 + bool "Level 2" + +config SPCR_TSEC1EP_3 + bool "Level 3 (highest priority)" + +endchoice + +choice + prompt "TSEC2 emergency priority" + +config SPCR_TSEC2EP_UNSET + bool "Don't set value" + +config SPCR_TSEC2EP_0 + bool "Level 0 (lowest priority)" + +config SPCR_TSEC2EP_1 + bool "Level 1" + +config SPCR_TSEC2EP_2 + bool "Level 2" + +config SPCR_TSEC2EP_3 + bool "Level 3 (highest priority)" + +endchoice + +endif + +config SPCR_OPT + hex + default 0x0 if SPCR_OPT_UNSET + default 0x0 if SPCR_OPT_NONE + default 0x800000 if SPCR_OPT_SPEC_READ + +config SPCR_TSECEP + hex + default 0x0 if SPCR_TSECEP_UNSET + default 0x0 if SPCR_TSECEP_0 + default 0x100 if SPCR_TSECEP_1 + default 0x200 if SPCR_TSECEP_2 + default 0x300 if SPCR_TSECEP_3 + +config SPCR_TSEC1EP + hex + default 0x0 if SPCR_TSEC1EP_UNSET + default 0x0 if SPCR_TSEC1EP_0 + default 0x100 if SPCR_TSEC1EP_1 + default 0x200 if SPCR_TSEC1EP_2 + default 0x300 if SPCR_TSEC1EP_3 + +config SPCR_TSEC2EP + hex + default 0x0 if SPCR_TSEC2EP_UNSET + default 0x0 if SPCR_TSEC2EP_0 + default 0x1 if SPCR_TSEC2EP_1 + default 0x2 if SPCR_TSEC2EP_2 + default 0x3 if SPCR_TSEC2EP_3 + +endmenu diff --git a/arch/powerpc/cpu/mpc83xx/initreg/initreg.h b/arch/powerpc/cpu/mpc83xx/initreg/initreg.h new file mode 100644 index 0000000000..63aa5c9466 --- /dev/null +++ b/arch/powerpc/cpu/mpc83xx/initreg/initreg.h @@ -0,0 +1,79 @@ +#define SPCR_PCIHPE_MASK 0x10000000 +#define SPCR_PCIPR_MASK 0x03000000 +#define SPCR_OPT_MASK 0x00800000 +#define SPCR_TBEN_MASK 0x00400000 +#define SPCR_COREPR_MASK 0x00300000 +#define SPCR_TSEC1DP_MASK 0x00003000 +#define SPCR_TSEC1BDP_MASK 0x00000C00 +#define SPCR_TSEC1EP_MASK 0x00000300 +#define SPCR_TSEC2DP_MASK 0x00000030 +#define SPCR_TSEC2BDP_MASK 0x0000000C +#define SPCR_TSEC2EP_MASK 0x00000003 +#define SPCR_TSECDP_MASK 0x00003000 +#define SPCR_TSECBDP_MASK 0x00000C00 +#define SPCR_TSECEP_MASK 0x00000300 + + const __be32 spcr_mask = +#if defined(CONFIG_SPCR_OPT) && !defined(CONFIG_SPCR_OPT_UNSET) + SPCR_OPT_MASK | +#endif +#if defined(CONFIG_SPCR_TSECEP) && !defined(CONFIG_SPCR_TSECEP_UNSET) + SPCR_TSECEP_MASK | +#endif +#if defined(CONFIG_SPCR_TSEC1EP) && !defined(CONFIG_SPCR_TSEC1EP_UNSET) + SPCR_TSEC1EP_MASK | +#endif +#if defined(CONFIG_SPCR_TSEC2EP) && !defined(CONFIG_SPCR_TSEC2EP_UNSET) + SPCR_TSEC2EP_MASK | +#endif + 0; + const __be32 spcr_val = +#if defined(CONFIG_SPCR_OPT) && !defined(CONFIG_SPCR_OPT_UNSET) + CONFIG_SPCR_OPT | +#endif +#if defined(CONFIG_SPCR_TSECEP) && !defined(CONFIG_SPCR_TSECEP_UNSET) + CONFIG_SPCR_TSECEP | +#endif +#if defined(CONFIG_SPCR_TSEC1EP) && !defined(CONFIG_SPCR_TSEC1EP_UNSET) + CONFIG_SPCR_TSEC1EP | +#endif +#if defined(CONFIG_SPCR_TSEC2EP) && !defined(CONFIG_SPCR_TSEC2EP_UNSET) + CONFIG_SPCR_TSEC2EP | +#endif + 0; + + const __be32 lcrr_mask = +#if defined(CONFIG_LCRR_DBYP) && !defined(CONFIG_LCRR_DBYP_UNSET) + LCRR_DBYP | +#endif +#if defined(CONFIG_LCRR_BUFCMDC) && !defined(CONFIG_LCRR_BUFCMDC_UNSET) + LCRR_BUFCMDC | +#endif +#if defined(CONFIG_LCRR_ECL) && !defined(CONFIG_LCRR_ECL_UNSET) + LCRR_ECL | +#endif +#if defined(CONFIG_LCRR_EADC) && !defined(CONFIG_LCRR_EADC_UNSET) + LCRR_EADC | +#endif +#if defined(CONFIG_LCRR_CLKDIV) && !defined(CONFIG_LCRR_CLKDIV_UNSET) + LCRR_CLKDIV | +#endif + 0; + + const __be32 lcrr_val = +#if defined(CONFIG_LCRR_DBYP) && !defined(CONFIG_LCRR_DBYP_UNSET) + CONFIG_LCRR_DBYP | +#endif +#if defined(CONFIG_LCRR_BUFCMDC) && !defined(CONFIG_LCRR_BUFCMDC_UNSET) + CONFIG_LCRR_BUFCMDC | +#endif +#if defined(CONFIG_LCRR_ECL) && !defined(CONFIG_LCRR_ECL_UNSET) + CONFIG_LCRR_ECL | +#endif +#if defined(CONFIG_LCRR_EADC) && !defined(CONFIG_LCRR_EADC_UNSET) + CONFIG_LCRR_EADC | +#endif +#if defined(CONFIG_LCRR_CLKDIV) && !defined(CONFIG_LCRR_CLKDIV_UNSET) + CONFIG_LCRR_CLKDIV | +#endif + 0; diff --git a/arch/powerpc/cpu/mpc83xx/lblaw/Kconfig b/arch/powerpc/cpu/mpc83xx/lblaw/Kconfig new file mode 100644 index 0000000000..b20f68b77a --- /dev/null +++ b/arch/powerpc/cpu/mpc83xx/lblaw/Kconfig @@ -0,0 +1,519 @@ +menu "LBLAW setup" + +choice + prompt "NAND LAWBAR for NAND SPL" + +config NAND_LBLAWBAR_PRELIM_NONE + bool "None" + +config NAND_LBLAWBAR_PRELIM_0 + bool "0" + depends on LBLAW0 + +config NAND_LBLAWBAR_PRELIM_1 + bool "1" + depends on LBLAW1 + +config NAND_LBLAWBAR_PRELIM_2 + bool "2" + depends on LBLAW2 + +config NAND_LBLAWBAR_PRELIM_3 + bool "3" + depends on LBLAW3 + +endchoice + +menuconfig LBLAW0 + bool "LBLAW0" + +if LBLAW0 + +config LBLAW0_ENABLE + bool "Window enable" + default "y" + +if !LBLAW0_ENABLE + +config LBLAW0_BASE + hex + default 0x0 + +endif + +if LBLAW0_ENABLE + +config LBLAW0_NAME + string "Identifier" + +config LBLAW0_BASE + hex "Window base" + +choice + prompt "Window size" + +config LBLAW0_LENGTH_4_KBYTES + bool "4 kb" + +config LBLAW0_LENGTH_8_KBYTES + bool "8 kb" + +config LBLAW0_LENGTH_16_KBYTES + bool "16 kb" + +config LBLAW0_LENGTH_32_KBYTES + bool "32 kb" + +config LBLAW0_LENGTH_64_KBYTES + bool "64 kb" + +config LBLAW0_LENGTH_128_KBYTES + bool "128 kb" + +config LBLAW0_LENGTH_256_KBYTES + bool "256 kb" + +config LBLAW0_LENGTH_512_KBYTES + bool "512 kb" + +config LBLAW0_LENGTH_1_MBYTES + bool "1 mb" + +config LBLAW0_LENGTH_2_MBYTES + bool "2 mb" + +config LBLAW0_LENGTH_4_MBYTES + bool "4 mb" + +config LBLAW0_LENGTH_8_MBYTES + bool "8 mb" + +config LBLAW0_LENGTH_16_MBYTES + bool "16 mb" + +config LBLAW0_LENGTH_32_MBYTES + bool "32 mb" + +config LBLAW0_LENGTH_64_MBYTES + bool "64 mb" + +config LBLAW0_LENGTH_128_MBYTES + bool "128 mb" + +config LBLAW0_LENGTH_256_MBYTES + bool "256 mb" + +config LBLAW0_LENGTH_512_MBYTES + bool "512 mb" + +config LBLAW0_LENGTH_1_GBYTES + bool "1 gb" + +config LBLAW0_LENGTH_2_GBYTES + bool "2 gb" + +endchoice + +endif # LBLAW0_ENABLE + +endif # LBLAW0 + +config LBLAW0_ENABLE_BIT + hex + default 0x0 if !LBLAW0_ENABLE + default 0x80000000 if LBLAW0_ENABLE + +config LBLAW0_LENGTH + hex + default 0x0 if !LBLAW0_ENABLE + default 0x0000000B if LBLAW0_LENGTH_4_KBYTES + default 0x0000000C if LBLAW0_LENGTH_8_KBYTES + default 0x0000000D if LBLAW0_LENGTH_16_KBYTES + default 0x0000000E if LBLAW0_LENGTH_32_KBYTES + default 0x0000000F if LBLAW0_LENGTH_64_KBYTES + default 0x00000010 if LBLAW0_LENGTH_128_KBYTES + default 0x00000011 if LBLAW0_LENGTH_256_KBYTES + default 0x00000012 if LBLAW0_LENGTH_512_KBYTES + default 0x00000013 if LBLAW0_LENGTH_1_MBYTES + default 0x00000014 if LBLAW0_LENGTH_2_MBYTES + default 0x00000015 if LBLAW0_LENGTH_4_MBYTES + default 0x00000016 if LBLAW0_LENGTH_8_MBYTES + default 0x00000017 if LBLAW0_LENGTH_16_MBYTES + default 0x00000018 if LBLAW0_LENGTH_32_MBYTES + default 0x00000019 if LBLAW0_LENGTH_64_MBYTES + default 0x0000001A if LBLAW0_LENGTH_128_MBYTES + default 0x0000001B if LBLAW0_LENGTH_256_MBYTES + default 0x0000001C if LBLAW0_LENGTH_512_MBYTES + default 0x0000001D if LBLAW0_LENGTH_1_GBYTES + default 0x0000001E if LBLAW0_LENGTH_2_GBYTES + +menuconfig LBLAW1 + bool "LBLAW1" + +if LBLAW1 + +config LBLAW1_ENABLE + bool "Window enable" + default "y" + +if !LBLAW1_ENABLE + +config LBLAW1_BASE + hex + default 0x0 + +endif + +if LBLAW1_ENABLE + +config LBLAW1_NAME + string "Identifier" + +config LBLAW1_BASE + hex "Window base" + +choice + prompt "Window size" + +config LBLAW1_LENGTH_4_KBYTES + bool "4 kb" + +config LBLAW1_LENGTH_8_KBYTES + bool "8 kb" + +config LBLAW1_LENGTH_16_KBYTES + bool "16 kb" + +config LBLAW1_LENGTH_32_KBYTES + bool "32 kb" + +config LBLAW1_LENGTH_64_KBYTES + bool "64 kb" + +config LBLAW1_LENGTH_128_KBYTES + bool "128 kb" + +config LBLAW1_LENGTH_256_KBYTES + bool "256 kb" + +config LBLAW1_LENGTH_512_KBYTES + bool "512 kb" + +config LBLAW1_LENGTH_1_MBYTES + bool "1 mb" + +config LBLAW1_LENGTH_2_MBYTES + bool "2 mb" + +config LBLAW1_LENGTH_4_MBYTES + bool "4 mb" + +config LBLAW1_LENGTH_8_MBYTES + bool "8 mb" + +config LBLAW1_LENGTH_16_MBYTES + bool "16 mb" + +config LBLAW1_LENGTH_32_MBYTES + bool "32 mb" + +config LBLAW1_LENGTH_64_MBYTES + bool "64 mb" + +config LBLAW1_LENGTH_128_MBYTES + bool "128 mb" + +config LBLAW1_LENGTH_256_MBYTES + bool "256 mb" + +config LBLAW1_LENGTH_512_MBYTES + bool "512 mb" + +config LBLAW1_LENGTH_1_GBYTES + bool "1 gb" + +config LBLAW1_LENGTH_2_GBYTES + bool "2 gb" + +endchoice + +endif # LBLAW1_ENABLE + +endif # LBLAW1 + +config LBLAW1_ENABLE_BIT + hex + default 0x0 if !LBLAW1_ENABLE + default 0x80000000 if LBLAW1_ENABLE + +config LBLAW1_LENGTH + hex + default 0x0 if !LBLAW1_ENABLE + default 0x0000000B if LBLAW1_LENGTH_4_KBYTES + default 0x0000000C if LBLAW1_LENGTH_8_KBYTES + default 0x0000000D if LBLAW1_LENGTH_16_KBYTES + default 0x0000000E if LBLAW1_LENGTH_32_KBYTES + default 0x0000000F if LBLAW1_LENGTH_64_KBYTES + default 0x00000010 if LBLAW1_LENGTH_128_KBYTES + default 0x00000011 if LBLAW1_LENGTH_256_KBYTES + default 0x00000012 if LBLAW1_LENGTH_512_KBYTES + default 0x00000013 if LBLAW1_LENGTH_1_MBYTES + default 0x00000014 if LBLAW1_LENGTH_2_MBYTES + default 0x00000015 if LBLAW1_LENGTH_4_MBYTES + default 0x00000016 if LBLAW1_LENGTH_8_MBYTES + default 0x00000017 if LBLAW1_LENGTH_16_MBYTES + default 0x00000018 if LBLAW1_LENGTH_32_MBYTES + default 0x00000019 if LBLAW1_LENGTH_64_MBYTES + default 0x0000001A if LBLAW1_LENGTH_128_MBYTES + default 0x0000001B if LBLAW1_LENGTH_256_MBYTES + default 0x0000001C if LBLAW1_LENGTH_512_MBYTES + default 0x0000001D if LBLAW1_LENGTH_1_GBYTES + default 0x0000001E if LBLAW1_LENGTH_2_GBYTES + +menuconfig LBLAW2 + bool "LBLAW2" + +if LBLAW2 + +config LBLAW2_ENABLE + bool "Window enable" + default "y" + +if !LBLAW2_ENABLE + +config LBLAW2_BASE + hex + default 0x0 + +endif + +if LBLAW2_ENABLE + +config LBLAW2_NAME + string "Identifier" + +config LBLAW2_BASE + hex "Window base" + +choice + prompt "Window size" + +config LBLAW2_LENGTH_4_KBYTES + bool "4 kb" + +config LBLAW2_LENGTH_8_KBYTES + bool "8 kb" + +config LBLAW2_LENGTH_16_KBYTES + bool "16 kb" + +config LBLAW2_LENGTH_32_KBYTES + bool "32 kb" + +config LBLAW2_LENGTH_64_KBYTES + bool "64 kb" + +config LBLAW2_LENGTH_128_KBYTES + bool "128 kb" + +config LBLAW2_LENGTH_256_KBYTES + bool "256 kb" + +config LBLAW2_LENGTH_512_KBYTES + bool "512 kb" + +config LBLAW2_LENGTH_1_MBYTES + bool "1 mb" + +config LBLAW2_LENGTH_2_MBYTES + bool "2 mb" + +config LBLAW2_LENGTH_4_MBYTES + bool "4 mb" + +config LBLAW2_LENGTH_8_MBYTES + bool "8 mb" + +config LBLAW2_LENGTH_16_MBYTES + bool "16 mb" + +config LBLAW2_LENGTH_32_MBYTES + bool "32 mb" + +config LBLAW2_LENGTH_64_MBYTES + bool "64 mb" + +config LBLAW2_LENGTH_128_MBYTES + bool "128 mb" + +config LBLAW2_LENGTH_256_MBYTES + bool "256 mb" + +config LBLAW2_LENGTH_512_MBYTES + bool "512 mb" + +config LBLAW2_LENGTH_1_GBYTES + bool "1 gb" + +config LBLAW2_LENGTH_2_GBYTES + bool "2 gb" + +endchoice + +endif # LBLAW2_ENABLE + +endif # LBLAW2 + +config LBLAW2_ENABLE_BIT + hex + default 0x0 if !LBLAW2_ENABLE + default 0x80000000 if LBLAW2_ENABLE + +config LBLAW2_LENGTH + hex + default 0x0 if !LBLAW2_ENABLE + default 0x0000000B if LBLAW2_LENGTH_4_KBYTES + default 0x0000000C if LBLAW2_LENGTH_8_KBYTES + default 0x0000000D if LBLAW2_LENGTH_16_KBYTES + default 0x0000000E if LBLAW2_LENGTH_32_KBYTES + default 0x0000000F if LBLAW2_LENGTH_64_KBYTES + default 0x00000010 if LBLAW2_LENGTH_128_KBYTES + default 0x00000011 if LBLAW2_LENGTH_256_KBYTES + default 0x00000012 if LBLAW2_LENGTH_512_KBYTES + default 0x00000013 if LBLAW2_LENGTH_1_MBYTES + default 0x00000014 if LBLAW2_LENGTH_2_MBYTES + default 0x00000015 if LBLAW2_LENGTH_4_MBYTES + default 0x00000016 if LBLAW2_LENGTH_8_MBYTES + default 0x00000017 if LBLAW2_LENGTH_16_MBYTES + default 0x00000018 if LBLAW2_LENGTH_32_MBYTES + default 0x00000019 if LBLAW2_LENGTH_64_MBYTES + default 0x0000001A if LBLAW2_LENGTH_128_MBYTES + default 0x0000001B if LBLAW2_LENGTH_256_MBYTES + default 0x0000001C if LBLAW2_LENGTH_512_MBYTES + default 0x0000001D if LBLAW2_LENGTH_1_GBYTES + default 0x0000001E if LBLAW2_LENGTH_2_GBYTES + +menuconfig LBLAW3 + bool "LBLAW3" + +if LBLAW3 + +config LBLAW3_ENABLE + bool "Window enable" + default "y" + +if !LBLAW3_ENABLE + +config LBLAW3_BASE + hex + default 0x0 + +endif + +if LBLAW3_ENABLE + +config LBLAW3_NAME + string "Identifier" + +config LBLAW3_BASE + hex "Window base" + +choice + prompt "Window size" + +config LBLAW3_LENGTH_4_KBYTES + bool "4 kb" + +config LBLAW3_LENGTH_8_KBYTES + bool "8 kb" + +config LBLAW3_LENGTH_16_KBYTES + bool "16 kb" + +config LBLAW3_LENGTH_32_KBYTES + bool "32 kb" + +config LBLAW3_LENGTH_64_KBYTES + bool "64 kb" + +config LBLAW3_LENGTH_128_KBYTES + bool "128 kb" + +config LBLAW3_LENGTH_256_KBYTES + bool "256 kb" + +config LBLAW3_LENGTH_512_KBYTES + bool "512 kb" + +config LBLAW3_LENGTH_1_MBYTES + bool "1 mb" + +config LBLAW3_LENGTH_2_MBYTES + bool "2 mb" + +config LBLAW3_LENGTH_4_MBYTES + bool "4 mb" + +config LBLAW3_LENGTH_8_MBYTES + bool "8 mb" + +config LBLAW3_LENGTH_16_MBYTES + bool "16 mb" + +config LBLAW3_LENGTH_32_MBYTES + bool "32 mb" + +config LBLAW3_LENGTH_64_MBYTES + bool "64 mb" + +config LBLAW3_LENGTH_128_MBYTES + bool "128 mb" + +config LBLAW3_LENGTH_256_MBYTES + bool "256 mb" + +config LBLAW3_LENGTH_512_MBYTES + bool "512 mb" + +config LBLAW3_LENGTH_1_GBYTES + bool "1 gb" + +config LBLAW3_LENGTH_2_GBYTES + bool "2 gb" + +endchoice + +endif # LBLAW3_ENABLE + +endif # LBLAW3 + +config LBLAW3_ENABLE_BIT + hex + default 0x0 if !LBLAW3_ENABLE + default 0x80000000 if LBLAW3_ENABLE + +config LBLAW3_LENGTH + hex + default 0x0 if !LBLAW3_ENABLE + default 0x0000000B if LBLAW3_LENGTH_4_KBYTES + default 0x0000000C if LBLAW3_LENGTH_8_KBYTES + default 0x0000000D if LBLAW3_LENGTH_16_KBYTES + default 0x0000000E if LBLAW3_LENGTH_32_KBYTES + default 0x0000000F if LBLAW3_LENGTH_64_KBYTES + default 0x00000010 if LBLAW3_LENGTH_128_KBYTES + default 0x00000011 if LBLAW3_LENGTH_256_KBYTES + default 0x00000012 if LBLAW3_LENGTH_512_KBYTES + default 0x00000013 if LBLAW3_LENGTH_1_MBYTES + default 0x00000014 if LBLAW3_LENGTH_2_MBYTES + default 0x00000015 if LBLAW3_LENGTH_4_MBYTES + default 0x00000016 if LBLAW3_LENGTH_8_MBYTES + default 0x00000017 if LBLAW3_LENGTH_16_MBYTES + default 0x00000018 if LBLAW3_LENGTH_32_MBYTES + default 0x00000019 if LBLAW3_LENGTH_64_MBYTES + default 0x0000001A if LBLAW3_LENGTH_128_MBYTES + default 0x0000001B if LBLAW3_LENGTH_256_MBYTES + default 0x0000001C if LBLAW3_LENGTH_512_MBYTES + default 0x0000001D if LBLAW3_LENGTH_1_GBYTES + default 0x0000001E if LBLAW3_LENGTH_2_GBYTES + +endmenu diff --git a/arch/powerpc/cpu/mpc83xx/lblaw/lblaw.h b/arch/powerpc/cpu/mpc83xx/lblaw/lblaw.h new file mode 100644 index 0000000000..6972afcc2c --- /dev/null +++ b/arch/powerpc/cpu/mpc83xx/lblaw/lblaw.h @@ -0,0 +1,55 @@ +#if defined(CONFIG_LBLAW0) +#define CONFIG_SYS_LBLAWBAR0_PRELIM \ + CONFIG_LBLAW0_BASE +#define CONFIG_SYS_LBLAWAR0_PRELIM (\ + CONFIG_LBLAW0_ENABLE_BIT |\ + CONFIG_LBLAW0_LENGTH \ +) +#endif + +#if defined(CONFIG_LBLAW1) +#define CONFIG_SYS_LBLAWBAR1_PRELIM \ + CONFIG_LBLAW1_BASE +#define CONFIG_SYS_LBLAWAR1_PRELIM (\ + CONFIG_LBLAW1_ENABLE_BIT |\ + CONFIG_LBLAW1_LENGTH \ +) +#endif + +#if defined(CONFIG_LBLAW2) +#define CONFIG_SYS_LBLAWBAR2_PRELIM \ + CONFIG_LBLAW2_BASE +#define CONFIG_SYS_LBLAWAR2_PRELIM (\ + CONFIG_LBLAW2_ENABLE_BIT |\ + CONFIG_LBLAW2_LENGTH \ +) +#endif + +#if defined(CONFIG_LBLAW3) +#define CONFIG_SYS_LBLAWBAR3_PRELIM \ + CONFIG_LBLAW3_BASE +#define CONFIG_SYS_LBLAWAR3_PRELIM (\ + CONFIG_LBLAW3_ENABLE_BIT |\ + CONFIG_LBLAW3_LENGTH \ +) +#endif + +#ifdef CONFIG_NAND_LBLAWBAR_PRELIM_0 +#define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR0_PRELIM +#define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR0_PRELIM +#endif + +#ifdef CONFIG_NAND_LBLAWBAR_PRELIM_1 +#define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM +#define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM +#endif + +#ifdef CONFIG_NAND_LBLAWBAR_PRELIM_2 +#define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR2_PRELIM +#define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR2_PRELIM +#endif + +#ifdef CONFIG_NAND_LBLAWBAR_PRELIM_3 +#define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR3_PRELIM +#define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR3_PRELIM +#endif diff --git a/arch/powerpc/cpu/mpc83xx/pcie.c b/arch/powerpc/cpu/mpc83xx/pcie.c index d3f979f3c4..b500ddd3f3 100644 --- a/arch/powerpc/cpu/mpc83xx/pcie.c +++ b/arch/powerpc/cpu/mpc83xx/pcie.c @@ -174,6 +174,41 @@ static void mpc83xx_pcie_register_hose(int bus, struct pci_region *reg, #endif /* CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES */ +int get_pcie_clk(int index) +{ + volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR; + u32 pci_sync_in; + u8 spmf; + u8 clkin_div; + u32 sccr; + u32 csb_clk; + u32 testval; + + clkin_div = ((im->clk.spmr & SPMR_CKID) >> SPMR_CKID_SHIFT); + sccr = im->clk.sccr; + pci_sync_in = CONFIG_SYS_CLK_FREQ / (1 + clkin_div); + spmf = (im->clk.spmr & SPMR_SPMF) >> SPMR_SPMF_SHIFT; + csb_clk = pci_sync_in * (1 + clkin_div) * spmf; + + if (index) + testval = (sccr & SCCR_PCIEXP2CM) >> SCCR_PCIEXP2CM_SHIFT; + else + testval = (sccr & SCCR_PCIEXP1CM) >> SCCR_PCIEXP1CM_SHIFT; + + switch (testval) { + case 0: + return 0; + case 1: + return csb_clk; + case 2: + return csb_clk / 2; + case 3: + return csb_clk / 3; + } + + return 0; +} + static void mpc83xx_pcie_init_bus(int bus, struct pci_region *reg) { immap_t *immr = (immap_t *)CONFIG_SYS_IMMR; @@ -269,11 +304,9 @@ static void mpc83xx_pcie_init_bus(int bus, struct pci_region *reg) /* Hose configure header is memory-mapped */ hose_cfg_base = (void *)pex; - get_clocks(); /* Configure the PCIE controller core clock ratio */ out_le32(hose_cfg_base + PEX_GCLK_RATIO, - (((bus ? gd->arch.pciexp2_clk : gd->arch.pciexp1_clk) - / 1000000) * 16) / 333); + ((get_pcie_clk(bus) / 1000000) * 16) / 333); udelay(1000000); /* Do Type 1 bridge configuration */ diff --git a/arch/powerpc/cpu/mpc83xx/spd_sdram.c b/arch/powerpc/cpu/mpc83xx/spd_sdram.c index 328a018eb6..8b5ecdb9ad 100644 --- a/arch/powerpc/cpu/mpc83xx/spd_sdram.c +++ b/arch/powerpc/cpu/mpc83xx/spd_sdram.c @@ -31,7 +31,7 @@ void board_add_ram_info(int use_default) printf(" (DDR%d", ((ddr->sdram_cfg & SDRAM_CFG_SDRAM_TYPE_MASK) >> SDRAM_CFG_SDRAM_TYPE_SHIFT) - 1); -#if defined(CONFIG_MPC8308) || defined(CONFIG_MPC831x) +#if defined(CONFIG_ARCH_MPC8308) || defined(CONFIG_ARCH_MPC831X) if ((ddr->sdram_cfg & SDRAM_CFG_DBW_MASK) == SDRAM_CFG_DBW_16) puts(", 16-bit"); else if ((ddr->sdram_cfg & SDRAM_CFG_DBW_MASK) == SDRAM_CFG_DBW_32) @@ -281,7 +281,7 @@ long int spd_sdram() /* * Set up LAWBAR for all of DDR. */ - ecm->bar = CONFIG_SYS_DDR_SDRAM_BASE & 0xfffff000; + ecm->bar = CONFIG_SYS_SDRAM_BASE & 0xfffff000; ecm->ar = (LAWAR_EN | LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & law_size)); debug("DDR:bar=0x%08x\n", ecm->bar); debug("DDR:ar=0x%08x\n", ecm->ar); @@ -426,7 +426,7 @@ long int spd_sdram() /* * Errata DDR6 work around: input enable 2 cycles earlier. - * including MPC834x Rev1.0/1.1 and MPC8360 Rev1.1/1.2. + * including MPC834X Rev1.0/1.1 and MPC8360 Rev1.1/1.2. */ if(PVR_MAJ(pvr) <= 1 && spd.mem_type == SPD_MEMTYPE_DDR){ if (caslat == 2) @@ -436,7 +436,7 @@ long int spd_sdram() else if (caslat == 4) ddr->debug_reg = 0x202c0000; /* CL=3.0 */ - __asm__ __volatile__ ("sync"); + sync(); debug("Errata DDR6 (debug_reg=0x%08x)\n", ddr->debug_reg); } @@ -765,7 +765,8 @@ long int spd_sdram() #endif debug("DDR:sdram_clk_cntl=0x%08x\n", ddr->sdram_clk_cntl); - asm("sync;isync"); + sync(); + isync(); udelay(600); @@ -834,7 +835,8 @@ long int spd_sdram() #endif /* Enable controller, and GO! */ ddr->sdram_cfg = sdram_cfg; - asm("sync;isync"); + sync(); + isync(); udelay(500); debug("DDR:sdram_cfg=0x%08x\n", ddr->sdram_cfg); @@ -843,6 +845,22 @@ long int spd_sdram() #endif /* CONFIG_SPD_EEPROM */ #if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) +static inline u32 mftbu(void) +{ + u32 rval; + + asm volatile("mftbu %0" : "=r" (rval)); + return rval; +} + +static inline u32 mftb(void) +{ + u32 rval; + + asm volatile("mftb %0" : "=r" (rval)); + return rval; +} + /* * Use timebase counter, get_timer() is not available * at this point of initialization yet. @@ -858,9 +876,9 @@ static __inline__ unsigned long get_tbms (void) /* get the timebase ticks */ do { - asm volatile ("mftbu %0":"=r" (tbu1):); - asm volatile ("mftb %0":"=r" (tbl):); - asm volatile ("mftbu %0":"=r" (tbu2):); + tbu1 = mftbu(); + tbl = mftb(); + tbu2 = mftbu(); } while (tbu1 != tbu2); /* convert ticks to ms */ @@ -897,7 +915,7 @@ void ddr_enable_ecc(unsigned int dram_size) for (p = 0; p < (u64*)(size); p++) { ppcDWstore((u32*)p, pattern); } - __asm__ __volatile__ ("sync"); + sync(); #endif t_end = get_tbms(); @@ -922,8 +940,8 @@ void ddr_enable_ecc(unsigned int dram_size) /* Enable errors for ECC */ ddr->err_disable &= ECC_ERROR_ENABLE; - __asm__ __volatile__ ("sync"); - __asm__ __volatile__ ("isync"); + sync(); + isync(); } #endif /* CONFIG_DDR_ECC */ diff --git a/arch/powerpc/cpu/mpc83xx/speed.c b/arch/powerpc/cpu/mpc83xx/speed.c index 39bc1c5340..e118a10fa8 100644 --- a/arch/powerpc/cpu/mpc83xx/speed.c +++ b/arch/powerpc/cpu/mpc83xx/speed.c @@ -85,35 +85,35 @@ int get_clocks(void) u32 lcrr; u32 csb_clk; -#if defined(CONFIG_MPC8308) || defined(CONFIG_MPC831x) || \ - defined(CONFIG_MPC834x) || defined(CONFIG_MPC837x) +#if defined(CONFIG_ARCH_MPC8308) || defined(CONFIG_ARCH_MPC831X) || \ + defined(CONFIG_ARCH_MPC834X) || defined(CONFIG_ARCH_MPC837X) u32 tsec1_clk; u32 tsec2_clk; u32 usbdr_clk; -#elif defined(CONFIG_MPC8309) +#elif defined(CONFIG_ARCH_MPC8309) u32 usbdr_clk; #endif -#ifdef CONFIG_MPC834x +#ifdef CONFIG_ARCH_MPC834X u32 usbmph_clk; #endif u32 core_clk; u32 i2c1_clk; -#if !defined(CONFIG_MPC832x) +#if !defined(CONFIG_ARCH_MPC832X) u32 i2c2_clk; #endif -#if defined(CONFIG_MPC8315) +#if defined(CONFIG_ARCH_MPC8315) u32 tdm_clk; #endif #if defined(CONFIG_FSL_ESDHC) u32 sdhc_clk; #endif -#if !defined(CONFIG_MPC8309) +#if !defined(CONFIG_ARCH_MPC8309) u32 enc_clk; #endif u32 lbiu_clk; u32 lclk_clk; u32 mem_clk; -#if defined(CONFIG_MPC8360) +#if defined(CONFIG_ARCH_MPC8360) u32 mem_sec_clk; #endif #if defined(CONFIG_QE) @@ -122,12 +122,12 @@ int get_clocks(void) u32 qe_clk; u32 brg_clk; #endif -#if defined(CONFIG_MPC8308) || defined(CONFIG_MPC831x) || \ - defined(CONFIG_MPC837x) +#if defined(CONFIG_ARCH_MPC8308) || defined(CONFIG_ARCH_MPC831X) || \ + defined(CONFIG_ARCH_MPC837X) u32 pciexp1_clk; u32 pciexp2_clk; #endif -#if defined(CONFIG_MPC837x) || defined(CONFIG_MPC8315) +#if defined(CONFIG_ARCH_MPC837X) || defined(CONFIG_ARCH_MPC8315) u32 sata_clk; #endif @@ -137,8 +137,8 @@ int get_clocks(void) clkin_div = ((im->clk.spmr & SPMR_CKID) >> SPMR_CKID_SHIFT); if (im->reset.rcwh & HRCWH_PCI_HOST) { -#if defined(CONFIG_83XX_CLKIN) - pci_sync_in = CONFIG_83XX_CLKIN / (1 + clkin_div); +#if defined(CONFIG_SYS_CLK_FREQ) + pci_sync_in = CONFIG_SYS_CLK_FREQ / (1 + clkin_div); #else pci_sync_in = 0xDEADBEEF; #endif @@ -155,8 +155,8 @@ int get_clocks(void) sccr = im->clk.sccr; -#if defined(CONFIG_MPC8308) || defined(CONFIG_MPC831x) || \ - defined(CONFIG_MPC834x) || defined(CONFIG_MPC837x) +#if defined(CONFIG_ARCH_MPC8308) || defined(CONFIG_ARCH_MPC831X) || \ + defined(CONFIG_ARCH_MPC834X) || defined(CONFIG_ARCH_MPC837X) switch ((sccr & SCCR_TSEC1CM) >> SCCR_TSEC1CM_SHIFT) { case 0: tsec1_clk = 0; @@ -176,8 +176,8 @@ int get_clocks(void) } #endif -#if defined(CONFIG_MPC830x) || defined(CONFIG_MPC831x) || \ - defined(CONFIG_MPC834x) || defined(CONFIG_MPC837x) +#if defined(CONFIG_ARCH_MPC830X) || defined(CONFIG_ARCH_MPC831X) || \ + defined(CONFIG_ARCH_MPC834X) || defined(CONFIG_ARCH_MPC837X) switch ((sccr & SCCR_USBDRCM) >> SCCR_USBDRCM_SHIFT) { case 0: usbdr_clk = 0; @@ -197,8 +197,8 @@ int get_clocks(void) } #endif -#if defined(CONFIG_MPC8308) || defined(CONFIG_MPC8315) || \ - defined(CONFIG_MPC834x) || defined(CONFIG_MPC837x) +#if defined(CONFIG_ARCH_MPC8308) || defined(CONFIG_ARCH_MPC8315) || \ + defined(CONFIG_ARCH_MPC834X) || defined(CONFIG_ARCH_MPC837X) switch ((sccr & SCCR_TSEC2CM) >> SCCR_TSEC2CM_SHIFT) { case 0: tsec2_clk = 0; @@ -216,7 +216,7 @@ int get_clocks(void) /* unknown SCCR_TSEC2CM value */ return -4; } -#elif defined(CONFIG_MPC8313) +#elif defined(CONFIG_ARCH_MPC8313) tsec2_clk = tsec1_clk; if (!(sccr & SCCR_TSEC1ON)) @@ -225,7 +225,7 @@ int get_clocks(void) tsec2_clk = 0; #endif -#if defined(CONFIG_MPC834x) +#if defined(CONFIG_ARCH_MPC834X) switch ((sccr & SCCR_USBMPHCM) >> SCCR_USBMPHCM_SHIFT) { case 0: usbmph_clk = 0; @@ -252,7 +252,7 @@ int get_clocks(void) return -6; } #endif -#if !defined(CONFIG_MPC8309) +#if !defined(CONFIG_ARCH_MPC8309) switch ((sccr & SCCR_ENCCM) >> SCCR_ENCCM_SHIFT) { case 0: enc_clk = 0; @@ -291,7 +291,7 @@ int get_clocks(void) return -8; } #endif -#if defined(CONFIG_MPC8315) +#if defined(CONFIG_ARCH_MPC8315) switch ((sccr & SCCR_TDMCM) >> SCCR_TDMCM_SHIFT) { case 0: tdm_clk = 0; @@ -311,27 +311,27 @@ int get_clocks(void) } #endif -#if defined(CONFIG_MPC834x) +#if defined(CONFIG_ARCH_MPC834X) i2c1_clk = tsec2_clk; -#elif defined(CONFIG_MPC8360) +#elif defined(CONFIG_ARCH_MPC8360) i2c1_clk = csb_clk; -#elif defined(CONFIG_MPC832x) +#elif defined(CONFIG_ARCH_MPC832X) i2c1_clk = enc_clk; -#elif defined(CONFIG_MPC8308) || defined(CONFIG_MPC831x) +#elif defined(CONFIG_ARCH_MPC8308) || defined(CONFIG_ARCH_MPC831X) i2c1_clk = enc_clk; #elif defined(CONFIG_FSL_ESDHC) i2c1_clk = sdhc_clk; -#elif defined(CONFIG_MPC837x) +#elif defined(CONFIG_ARCH_MPC837X) i2c1_clk = enc_clk; -#elif defined(CONFIG_MPC8309) +#elif defined(CONFIG_ARCH_MPC8309) i2c1_clk = csb_clk; #endif -#if !defined(CONFIG_MPC832x) +#if !defined(CONFIG_ARCH_MPC832X) i2c2_clk = csb_clk; /* i2c-2 clk is equal to csb clk */ #endif -#if defined(CONFIG_MPC8308) || defined(CONFIG_MPC831x) || \ - defined(CONFIG_MPC837x) +#if defined(CONFIG_ARCH_MPC8308) || defined(CONFIG_ARCH_MPC831X) || \ + defined(CONFIG_ARCH_MPC837X) switch ((sccr & SCCR_PCIEXP1CM) >> SCCR_PCIEXP1CM_SHIFT) { case 0: pciexp1_clk = 0; @@ -369,7 +369,7 @@ int get_clocks(void) } #endif -#if defined(CONFIG_MPC837x) || defined(CONFIG_MPC8315) +#if defined(CONFIG_ARCH_MPC837X) || defined(CONFIG_ARCH_MPC8315) switch ((sccr & SCCR_SATA1CM) >> SCCR_SATA1CM_SHIFT) { case 0: sata_clk = 0; @@ -407,7 +407,7 @@ int get_clocks(void) (1 + ((im->clk.spmr & SPMR_DDRCM) >> SPMR_DDRCM_SHIFT)); corepll = (im->clk.spmr & SPMR_COREPLL) >> SPMR_COREPLL_SHIFT; -#if defined(CONFIG_MPC8360) +#if defined(CONFIG_ARCH_MPC8360) mem_sec_clk = csb_clk * (1 + ((im->clk.spmr & SPMR_LBIUCM) >> SPMR_LBIUCM_SHIFT)); #endif @@ -448,18 +448,18 @@ int get_clocks(void) #endif gd->arch.csb_clk = csb_clk; -#if defined(CONFIG_MPC8308) || defined(CONFIG_MPC831x) || \ - defined(CONFIG_MPC834x) || defined(CONFIG_MPC837x) +#if defined(CONFIG_ARCH_MPC8308) || defined(CONFIG_ARCH_MPC831X) || \ + defined(CONFIG_ARCH_MPC834X) || defined(CONFIG_ARCH_MPC837X) gd->arch.tsec1_clk = tsec1_clk; gd->arch.tsec2_clk = tsec2_clk; gd->arch.usbdr_clk = usbdr_clk; -#elif defined(CONFIG_MPC8309) +#elif defined(CONFIG_ARCH_MPC8309) gd->arch.usbdr_clk = usbdr_clk; #endif -#if defined(CONFIG_MPC834x) +#if defined(CONFIG_ARCH_MPC834X) gd->arch.usbmph_clk = usbmph_clk; #endif -#if defined(CONFIG_MPC8315) +#if defined(CONFIG_ARCH_MPC8315) gd->arch.tdm_clk = tdm_clk; #endif #if defined(CONFIG_FSL_ESDHC) @@ -467,28 +467,28 @@ int get_clocks(void) #endif gd->arch.core_clk = core_clk; gd->arch.i2c1_clk = i2c1_clk; -#if !defined(CONFIG_MPC832x) +#if !defined(CONFIG_ARCH_MPC832X) gd->arch.i2c2_clk = i2c2_clk; #endif -#if !defined(CONFIG_MPC8309) +#if !defined(CONFIG_ARCH_MPC8309) gd->arch.enc_clk = enc_clk; #endif gd->arch.lbiu_clk = lbiu_clk; gd->arch.lclk_clk = lclk_clk; gd->mem_clk = mem_clk; -#if defined(CONFIG_MPC8360) +#if defined(CONFIG_ARCH_MPC8360) gd->arch.mem_sec_clk = mem_sec_clk; #endif #if defined(CONFIG_QE) gd->arch.qe_clk = qe_clk; gd->arch.brg_clk = brg_clk; #endif -#if defined(CONFIG_MPC8308) || defined(CONFIG_MPC831x) || \ - defined(CONFIG_MPC837x) +#if defined(CONFIG_ARCH_MPC8308) || defined(CONFIG_ARCH_MPC831X) || \ + defined(CONFIG_ARCH_MPC837X) gd->arch.pciexp1_clk = pciexp1_clk; gd->arch.pciexp2_clk = pciexp2_clk; #endif -#if defined(CONFIG_MPC837x) || defined(CONFIG_MPC8315) +#if defined(CONFIG_ARCH_MPC837X) || defined(CONFIG_ARCH_MPC8315) gd->arch.sata_clk = sata_clk; #endif gd->pci_clk = pci_sync_in; @@ -516,6 +516,11 @@ ulong get_ddr_freq(ulong dummy) return gd->mem_clk; } +int get_serial_clock(void) +{ + return get_bus_freq(0); +} + static int do_clocks(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) { char buf[32]; @@ -536,21 +541,21 @@ static int do_clocks(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) printf(" Local Bus: %-4s MHz\n", strmhz(buf, gd->arch.lclk_clk)); printf(" DDR: %-4s MHz\n", strmhz(buf, gd->mem_clk)); -#if defined(CONFIG_MPC8360) +#if defined(CONFIG_ARCH_MPC8360) printf(" DDR Secondary: %-4s MHz\n", strmhz(buf, gd->arch.mem_sec_clk)); #endif -#if !defined(CONFIG_MPC8309) +#if !defined(CONFIG_ARCH_MPC8309) printf(" SEC: %-4s MHz\n", strmhz(buf, gd->arch.enc_clk)); #endif printf(" I2C1: %-4s MHz\n", strmhz(buf, gd->arch.i2c1_clk)); -#if !defined(CONFIG_MPC832x) +#if !defined(CONFIG_ARCH_MPC832X) printf(" I2C2: %-4s MHz\n", strmhz(buf, gd->arch.i2c2_clk)); #endif -#if defined(CONFIG_MPC8315) +#if defined(CONFIG_ARCH_MPC8315) printf(" TDM: %-4s MHz\n", strmhz(buf, gd->arch.tdm_clk)); #endif @@ -558,30 +563,30 @@ static int do_clocks(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) printf(" SDHC: %-4s MHz\n", strmhz(buf, gd->arch.sdhc_clk)); #endif -#if defined(CONFIG_MPC8308) || defined(CONFIG_MPC831x) || \ - defined(CONFIG_MPC834x) || defined(CONFIG_MPC837x) +#if defined(CONFIG_ARCH_MPC8308) || defined(CONFIG_ARCH_MPC831X) || \ + defined(CONFIG_ARCH_MPC834X) || defined(CONFIG_ARCH_MPC837X) printf(" TSEC1: %-4s MHz\n", strmhz(buf, gd->arch.tsec1_clk)); printf(" TSEC2: %-4s MHz\n", strmhz(buf, gd->arch.tsec2_clk)); printf(" USB DR: %-4s MHz\n", strmhz(buf, gd->arch.usbdr_clk)); -#elif defined(CONFIG_MPC8309) +#elif defined(CONFIG_ARCH_MPC8309) printf(" USB DR: %-4s MHz\n", strmhz(buf, gd->arch.usbdr_clk)); #endif -#if defined(CONFIG_MPC834x) +#if defined(CONFIG_ARCH_MPC834X) printf(" USB MPH: %-4s MHz\n", strmhz(buf, gd->arch.usbmph_clk)); #endif -#if defined(CONFIG_MPC8308) || defined(CONFIG_MPC831x) || \ - defined(CONFIG_MPC837x) +#if defined(CONFIG_ARCH_MPC8308) || defined(CONFIG_ARCH_MPC831X) || \ + defined(CONFIG_ARCH_MPC837X) printf(" PCIEXP1: %-4s MHz\n", strmhz(buf, gd->arch.pciexp1_clk)); printf(" PCIEXP2: %-4s MHz\n", strmhz(buf, gd->arch.pciexp2_clk)); #endif -#if defined(CONFIG_MPC837x) || defined(CONFIG_MPC8315) +#if defined(CONFIG_ARCH_MPC837X) || defined(CONFIG_ARCH_MPC8315) printf(" SATA: %-4s MHz\n", strmhz(buf, gd->arch.sata_clk)); #endif diff --git a/arch/powerpc/cpu/mpc83xx/spl_minimal.c b/arch/powerpc/cpu/mpc83xx/spl_minimal.c index 746f1febba..133f7abc31 100644 --- a/arch/powerpc/cpu/mpc83xx/spl_minimal.c +++ b/arch/powerpc/cpu/mpc83xx/spl_minimal.c @@ -6,6 +6,9 @@ #include <common.h> #include <mpc83xx.h> +#include "lblaw/lblaw.h" +#include "elbc/elbc.h" + DECLARE_GLOBAL_DATA_PTR; /* @@ -24,16 +27,16 @@ void cpu_init_f (volatile immap_t * im) /* system performance tweaking */ -#ifdef CONFIG_SYS_ACR_PIPE_DEP +#ifndef CONFIG_ACR_PIPE_DEP_UNSET /* Arbiter pipeline depth */ im->arbiter.acr = (im->arbiter.acr & ~ACR_PIPE_DEP) | - (CONFIG_SYS_ACR_PIPE_DEP << ACR_PIPE_DEP_SHIFT); + CONFIG_ACR_PIPE_DEP; #endif -#ifdef CONFIG_SYS_ACR_RPTCNT +#ifndef CONFIG_ACR_RPTCNT_UNSET /* Arbiter repeat count */ im->arbiter.acr = (im->arbiter.acr & ~(ACR_RPTCNT)) | - (CONFIG_SYS_ACR_RPTCNT << ACR_RPTCNT_SHIFT); + CONFIG_ACR_RPTCNT; #endif #ifdef CONFIG_SYS_SPCR_OPT @@ -89,3 +92,11 @@ void puts(const char *str) while (*str) putc(*str++); } + +ulong get_bus_freq(ulong dummy) +{ + volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR; + u8 spmf = (im->clk.spmr & SPMR_SPMF) >> SPMR_SPMF_SHIFT; + + return CONFIG_SYS_CLK_FREQ * spmf; +} diff --git a/arch/powerpc/cpu/mpc83xx/start.S b/arch/powerpc/cpu/mpc83xx/start.S index c00bb31363..f4a8a766c3 100644 --- a/arch/powerpc/cpu/mpc83xx/start.S +++ b/arch/powerpc/cpu/mpc83xx/start.S @@ -24,6 +24,10 @@ #include <asm/mmu.h> #include <asm/u-boot.h> +#include "hrcw/hrcw.h" +#include "bats/bats.h" +#include "hid/hid.h" + /* We don't want the MMU yet. */ #undef MSR_KERNEL @@ -115,18 +119,6 @@ disable_addr_trans: mtspr SRR1, r3 rfi - .globl ppcDWstore -ppcDWstore: - lfd 1, 0(r4) - stfd 1, 0(r3) - blr - - .globl ppcDWload -ppcDWload: - lfd 1, 0(r3) - stfd 1, 0(r4) - blr - #ifndef CONFIG_DEFAULT_IMMR #error CONFIG_DEFAULT_IMMR must be defined #endif /* CONFIG_DEFAULT_IMMR */ diff --git a/arch/powerpc/cpu/mpc83xx/sysio/Kconfig b/arch/powerpc/cpu/mpc83xx/sysio/Kconfig new file mode 100644 index 0000000000..9e1f158712 --- /dev/null +++ b/arch/powerpc/cpu/mpc83xx/sysio/Kconfig @@ -0,0 +1,7 @@ +menu "System I/O configuration" + +if ARCH_MPC8308 +source "arch/powerpc/cpu/mpc83xx/sysio/Kconfig.mpc8308" +endif + +endmenu diff --git a/arch/powerpc/cpu/mpc83xx/sysio/Kconfig.mpc8308 b/arch/powerpc/cpu/mpc83xx/sysio/Kconfig.mpc8308 new file mode 100644 index 0000000000..de62171b30 --- /dev/null +++ b/arch/powerpc/cpu/mpc83xx/sysio/Kconfig.mpc8308 @@ -0,0 +1,323 @@ +choice + prompt "SPI group" + +config SICR_SPI_SPI + bool "SPI" + +config SICR_SPI_MSRCID + bool "MSRCID" + +config SICR_SPI_LSRCID + bool "LSRCID" + +endchoice + +choice + prompt "UART group" + +config SICR_UART_SPI + bool "UART" + +config SICR_UART_MSRCID + bool "MSRCID" + +config SICR_UART_LSRCID + bool "LSRCID" + +endchoice + +choice + prompt "IRQ group" + +config SICR_IRQ_SPI + bool "IRQ" + +config SICR_IRQ_MCP_CKSTOP + bool "MCP/CKSTOP" + +config SICR_IRQ_INTA + bool "INTA" + +endchoice + +choice + prompt "I2C2 group" + +config SICR_I2C2_I2C + bool "IRQ" + +config SICR_I2C2_CKSTOP + bool "CKSTOP" + +endchoice + +choice + prompt "ETSEC1 A group" + +config SICR_ETSEC1_A_TSEC2 + bool "TSEC1" + +config SICR_ETSEC1_A_TSEC_GTX_CLK125 + bool "TSEC1 GTX_CLK125" + +endchoice + +choice + prompt "eSDHC A group" + +config SICR_ESDHC_A_SD + bool "SD" + +config SICR_ESDHC_A_GTM + bool "GTM" + +config SICR_ESDHC_A_GPIO + bool "GPIO" + +endchoice + +choice + prompt "eSDHC B group" + +config SICR_ESDHC_B_SD + bool "SD" + +config SICR_ESDHC_B_GTM + bool "GTM" + +config SICR_ESDHC_B_GPIO + bool "GPIO" + +endchoice + +choice + prompt "eSDHC C group" + +config SICR_ESDHC_C_SD + bool "SD" + +config SICR_ESDHC_C_GTM + bool "GTM" + +config SICR_ESDHC_C_GPIO + bool "GPIO" + +endchoice + +choice + prompt "GPIO A group" + +config SICR_GPIO_A_GPIO + bool "GPIO" + +config SICR_GPIO_A_TSEC2 + bool "TSEC2" + +endchoice + +choice + prompt "GPIO B group" + +config SICR_GPIO_B_GPIO + bool "GPIO" + +config SICR_GPIO_B_TSEC2 + bool "TSEC2" + +config SICR_GPIO_B_TSEC_GTX_CLK125 + bool "TSEC2 GTX_CLK125" + +endchoice + +choice + prompt "IEEE1588 A group" + +config SICR_IEEE1588_A_TSEC + bool "TSEC" + +config SICR_IEEE1588_A_GPIO + bool "GPIO" + +endchoice + +choice + prompt "USB group" + +config SICR_USB_TSEC + bool "USB" + +endchoice + +choice + prompt "GTM group" + +config SICR_GTM_TSEC + bool "GTM" + +config SICR_GTM_GPIO + bool "GPIO" + +endchoice + +choice + prompt "IEEE1588 B group" + +config SICR_IEEE1588_B_GPIO + bool "GPIO" + +endchoice + +choice + prompt "ETSEC2 group" + +config SICR_ETSEC2_TSEC2 + bool "TSEC2" + +config SICR_ETSEC2_GPIO + bool "GPIO" + +endchoice + +choice + prompt "GPIO selection" + +config SICR_GPIOSEL_GPIO + bool "GPIO_A, GPIO_B" + +config SICR_GPIOSEL_IEEE1588 + bool "IEEE1588_A, IEEE1588_B, ETSEC2" + +endchoice + +choice + prompt "IEEE1588 timer output buffer impedance" + +config SICR_TMROBI_3_3_V + bool "40 Ohm, 3.3V" + +config SICR_TMROBI_2_5_V + bool "40 Ohm, 2.5V" + +endchoice + +choice + prompt "TSEC1 output buffer impedance" + +config SICR_TMSOBI1_3_3_V + bool "40 Ohm, 3.3V" + +config SICR_TMSOBI1_2_5_V + bool "40 Ohm, 2.5V" + +endchoice + +choice + prompt "TSEC2 output buffer impedance" + +config SICR_TMSOBI2_3_3_V + bool "40 Ohm, 3.3V" + +config SICR_TMSOBI2_2_5_V + bool "40 Ohm, 2.5V" + +endchoice + +config SICRL_SPI + hex + default 0x0 if SICR_SPI_SPI + default 0x10000000 if SICR_SPI_MSRCID + default 0x30000000 if SICR_SPI_LSRCID + +config SICRL_UART + hex + default 0x0 if SICR_UART_SPI + default 0x4000000 if SICR_UART_MSRCID + default 0xc000000 if SICR_UART_LSRCID + +config SICRL_IRQ + hex + default 0x0 if SICR_IRQ_SPI + default 0x1000000 if SICR_IRQ_MCP_CKSTOP + default 0x3000000 if SICR_IRQ_INTA + +config SICRL_I2C2 + hex + default 0x0 if SICR_I2C2_I2C + default 0x100000 if SICR_I2C2_CKSTOP + +config SICRL_ETSEC1_A + hex + default 0x0 if SICR_ETSEC1_A_TSEC2 + default 0x40 if SICR_ETSEC1_A_TSEC_GTX_CLK125 + +config SICRH_ESDHC_A + hex + default 0x0 if SICR_ESDHC_A_SD + default 0x40000000 if SICR_ESDHC_A_GTM + default 0xc0000000 if SICR_ESDHC_A_GPIO + +config SICRH_ESDHC_B + hex + default 0x0 if SICR_ESDHC_B_SD + default 0x10000000 if SICR_ESDHC_B_GTM + default 0x30000000 if SICR_ESDHC_B_GPIO + +config SICRH_ESDHC_C + hex + default 0x0 if SICR_ESDHC_C_SD + default 0x4000000 if SICR_ESDHC_C_GTM + default 0xc000000 if SICR_ESDHC_C_GPIO + +config SICRH_GPIO_A + hex + default 0x0 if SICR_GPIO_A_GPIO + default 0x1000000 if SICR_GPIO_A_TSEC2 + +config SICRH_GPIO_B + hex + default 0x0 if SICR_GPIO_B_GPIO + default 0x400000 if SICR_GPIO_B_TSEC2 + default 0x800000 if SICR_GPIO_B_TSEC_GTX_CLK125 + +config SICRH_IEEE1588_A + hex + default 0x100000 if SICR_IEEE1588_A_TSEC + default 0x300000 if SICR_IEEE1588_A_GPIO + +config SICRH_USB + hex + default 0x40000 if SICR_USB_TSEC + +config SICRH_GTM + hex + default 0x10000 if SICR_GTM_TSEC + default 0x30000 if SICR_GTM_GPIO + +config SICRH_IEEE1588_B + hex + default 0xc000 if SICR_IEEE1588_B_GPIO + +config SICRH_ETSEC2 + hex + default 0x1000 if SICR_ETSEC2_TSEC2 + default 0x3000 if SICR_ETSEC2_GPIO + +config SICRH_GPIOSEL + hex + default 0x0 if SICR_GPIOSEL_GPIO + default 0x100 if SICR_GPIOSEL_IEEE1588 + +config SICRH_TMROBI + hex + default 0x0 if SICR_TMROBI_3_3_V + default 0x10 if SICR_TMROBI_2_5_V + +config SICRH_TMSOBI1 + hex + default 0x0 if SICR_TMSOBI1_3_3_V + default 0x2 if SICR_TMSOBI1_2_5_V + +config SICRH_TMSOBI2 + hex + default 0x0 if SICR_TMSOBI2_3_3_V + default 0x1 if SICR_TMSOBI2_2_5_V diff --git a/arch/powerpc/cpu/mpc83xx/sysio/sysio.h b/arch/powerpc/cpu/mpc83xx/sysio/sysio.h new file mode 100644 index 0000000000..f8c2f104c1 --- /dev/null +++ b/arch/powerpc/cpu/mpc83xx/sysio/sysio.h @@ -0,0 +1,32 @@ +#ifdef CONFIG_ARCH_MPC8308 + +#ifndef CONFIG_SYS_SICRL +#define CONFIG_SYS_SICRL (\ + CONFIG_SICRL_SPI |\ + CONFIG_SICRL_UART |\ + CONFIG_SICRL_IRQ |\ + CONFIG_SICRL_I2C2 |\ + CONFIG_SICRL_ETSEC1_A \ +) +#endif + +#ifndef CONFIG_SYS_SICRH +#define CONFIG_SYS_SICRH (\ + CONFIG_SICRH_ESDHC_A |\ + CONFIG_SICRH_ESDHC_B |\ + CONFIG_SICRH_ESDHC_C |\ + CONFIG_SICRH_GPIO_A |\ + CONFIG_SICRH_GPIO_B |\ + CONFIG_SICRH_IEEE1588_A |\ + CONFIG_SICRH_USB |\ + CONFIG_SICRH_GTM |\ + CONFIG_SICRH_IEEE1588_B |\ + CONFIG_SICRH_ETSEC2 |\ + CONFIG_SICRH_GPIOSEL |\ + CONFIG_SICRH_TMROBI |\ + CONFIG_SICRH_TMSOBI1 |\ + CONFIG_SICRH_TMSOBI2 \ +) +#endif + +#endif diff --git a/arch/powerpc/cpu/mpc83xx/u-boot.lds b/arch/powerpc/cpu/mpc83xx/u-boot.lds index 37a13fd8c2..d10f528da4 100644 --- a/arch/powerpc/cpu/mpc83xx/u-boot.lds +++ b/arch/powerpc/cpu/mpc83xx/u-boot.lds @@ -52,6 +52,12 @@ SECTIONS __ex_table : { *(__ex_table) } __stop___ex_table = .; + /* + * _end - This is end of u-boot.bin image. + * dtb will be appended here to make u-boot-dtb.bin + */ + _end = .; + . = ALIGN(4096); __init_begin = .; .text.init : { *(.text.init) } diff --git a/arch/powerpc/cpu/mpc8xxx/fsl_lbc.c b/arch/powerpc/cpu/mpc8xxx/fsl_lbc.c index 13545fc6ad..c43732f7c5 100644 --- a/arch/powerpc/cpu/mpc8xxx/fsl_lbc.c +++ b/arch/powerpc/cpu/mpc8xxx/fsl_lbc.c @@ -6,6 +6,10 @@ #include <common.h> #include <asm/fsl_lbc.h> +#ifdef CONFIG_MPC83xx +#include "../mpc83xx/elbc/elbc.h" +#endif + #ifdef CONFIG_MPC85xx /* Boards should provide their own version of this if they use lbc sdram */ static void __lbc_sdram_init(void) diff --git a/arch/powerpc/cpu/mpc8xxx/fsl_pamu.c b/arch/powerpc/cpu/mpc8xxx/fsl_pamu.c index 23cc5a32ac..d81af70f44 100644 --- a/arch/powerpc/cpu/mpc8xxx/fsl_pamu.c +++ b/arch/powerpc/cpu/mpc8xxx/fsl_pamu.c @@ -131,10 +131,10 @@ static int pamu_config_ppaace(uint32_t liodn, uint64_t win_addr, set_bf(ppaace->addr_bitfields, PAACE_AF_AP, PAACE_AP_PERMS_ALL); } - asm volatile("sync" : : : "memory"); + sync(); /* Mark the ppace entry valid */ ppaace->addr_bitfields |= PAACE_V_VALID; - asm volatile("sync" : : : "memory"); + sync(); return 0; } @@ -279,7 +279,7 @@ int pamu_init(void) out_be32(®s->splah, spaact_lim >> 32); out_be32(®s->splal, (uint32_t)spaact_lim); } - asm volatile("sync" : : : "memory"); + sync(); base_addr += PAMU_OFFSET; } @@ -294,7 +294,7 @@ void pamu_enable(void) for (i = 0; i < CONFIG_NUM_PAMU; i++) { setbits_be32((void *)base_addr + PAMU_PCR_OFFSET, PAMU_PCR_PE); - asm volatile("sync" : : : "memory"); + sync(); base_addr += PAMU_OFFSET; } } @@ -318,7 +318,7 @@ void pamu_reset(void) out_be32(®s->splal, 0); clrbits_be32((void *)regs + PAMU_PCR_OFFSET, PAMU_PCR_PE); - asm volatile("sync" : : : "memory"); + sync(); base_addr += PAMU_OFFSET; } } @@ -331,7 +331,7 @@ void pamu_disable(void) for (i = 0; i < CONFIG_NUM_PAMU; i++) { clrbits_be32((void *)base_addr + PAMU_PCR_OFFSET, PAMU_PCR_PE); - asm volatile("sync" : : : "memory"); + sync(); base_addr += PAMU_OFFSET; } } diff --git a/arch/powerpc/dts/.gitignore b/arch/powerpc/dts/.gitignore new file mode 100644 index 0000000000..b60ed208c7 --- /dev/null +++ b/arch/powerpc/dts/.gitignore @@ -0,0 +1 @@ +*.dtb diff --git a/arch/powerpc/dts/Makefile b/arch/powerpc/dts/Makefile index f080a96891..6a28f802c2 100644 --- a/arch/powerpc/dts/Makefile +++ b/arch/powerpc/dts/Makefile @@ -2,6 +2,7 @@ dtb-$(CONFIG_TARGET_T2080QDS) += t2080qds.dtb dtb-$(CONFIG_TARGET_MCR3000) += mcr3000.dtb +dtb-$(CONFIG_TARGET_GAZERBEAM) += gazerbeam.dtb targets += $(dtb-y) diff --git a/arch/powerpc/dts/gazerbeam.dts b/arch/powerpc/dts/gazerbeam.dts new file mode 100644 index 0000000000..96c03c77ae --- /dev/null +++ b/arch/powerpc/dts/gazerbeam.dts @@ -0,0 +1,602 @@ +/* + * Gazerbeam CON Device Tree Source + * + * (C) Copyright 2015 + * Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#include "gdsys/mpc8308.dtsi" + +/include/ "gdsys/gazerbeam-base.dtsi" + +/include/ "gdsys/soc/i2c/cirrus-audio-codec.dtsi" +/include/ "gdsys/soc/i2c/dallas-rtc.dtsi" +/include/ "gdsys/soc/lbc/gazerbeam.dtsi" +/include/ "gdsys/soc/nor/flash-80k-partition.dtsi" + +&board_lbc { + FPGA0:iocon_uart@1,0 { + reg = <0x1 0x0 0x100000>; + little-endian; + interrupts = <48 0x8>; + interrupt-parent = <&ipic>; + }; + + FPGA1:iocon_uart@2,0 { + reg = <0x2 0x0 0x100000>; + little-endian; + interrupts = <17 0x8>; + interrupt-parent = <&ipic>; + }; +}; + +&FPGA0 { + compatible = "gdsys,iocon_fpga"; + #gpio-cells = <2>; + gpio-controller; + bus = <&FPGA0BUS>; + unit_id = <0>; + fpga-type = <1>; + usb_base = <0x0080>; + audio_base = <0x0040>; + timebase_base = <0x013c>; + + /* + * for every interrupt source there must be a dataset specifying + * 1. type (1: standard) + * 2. status register offset + * 3. mask register offset + * 4. default mask + */ + fpga_interrupt_sources = + <1 0x000a 0x000c 0x4000>, /* 0: TOP_INTERRUPT */ + <1 0x001c 0x001e 0x0000>; /* 1: EXTENDED_INTERRUPT */ + /* + * for every interrupt there must be a dataset specifying + * 1. type (1: status, 2: event) + * 2. interrupt source index + * 3. interrupt register bit + * 4. mask register bit + */ + #fpga_interrupt_map-cells = <4>; + fpga_interrupt_map = + <1 0 14 14>, /* 0: EXTENDED_INTERRUPT */ + <1 0 0 0>, /* 1: VIDEO 0 */ + <1 0 1 1>, /* 2: VIDEO 1 */ + <1 0 2 2>, /* 3: VIDEO IC 0 */ + <1 0 3 3>, /* 4: VIDEO IC 1 */ + <1 0 4 4>, /* 5: IIC MAIN */ + <1 0 6 6>, /* 6: IIC VIDEO 0 */ + <1 0 7 7>, /* 7: IIC VIDEO 1 */ + <1 1 0 0>, /* 8: OSD 0 */ + <1 1 1 1>, /* 9: OSD 1 */ + <1 1 2 2>, /* 10: SPDIF 0 */ + <1 1 3 3>, /* 11: SPDIF 1 */ + <1 0 12 12>, /* 12: COMM 0 */ + <1 0 13 13>, /* 13: COMM 1 */ + <1 0 10 10>, /* 14: COMM 2 */ + <1 0 11 11>, /* 15: COMM 3 */ + <2 0 5 5>, /* 16: MDIO */ + <1 0 8 8>, /* 17: PHY */ + <1 1 4 4>, /* 18: RS232 */ + <1 1 5 5>, /* 19: AUDIO */ + <1 1 8 8>, /* 20: PROC_AUDIO */ + <1 1 7 7>, /* 21: USB/ETH-UART INT */ + <2 1 10 10>, /* 22: AXI Bridge 0 */ + <2 1 11 11>, /* 23: AXI Bridge 1 */ + <2 1 9 9>, /* 24: USB/ETH-Secondary IIC */ + <>; +}; + +&FPGA1 { + compatible = "gdsys,iocon_fpga"; + #gpio-cells = <2>; + gpio-controller; + bus = <&FPGA1BUS>; + unit_id = <1>; + fpga-type = <1>; + usb_base = <0x0070>; + audio_base = <0x0040>; + timebase_base = <0x013c>; + + /* + * for every interrupt source there must be a dataset specifying + * 1. type (1: standard) + * 2. status register offset + * 3. mask register offset + * 4. default mask + */ + fpga_interrupt_sources = + <1 0x000a 0x000c 0x4000>, /* 0: TOP_INTERRUPT */ + <1 0x001c 0x001e 0x0000>; /* 1: EXTENDED_INTERRUPT */ + /* + * for every interrupt there must be a dataset specifying + * 1. type (1: status, 2: event) + * 2. interrupt source index + * 3. interrupt register bit + * 4. mask register bit + */ + #fpga_interrupt_map-cells = <4>; + fpga_interrupt_map = + <1 0 14 14>, /* 0: EXTENDED_INTERRUPT */ + <1 0 0 0>, /* 1: VIDEO 0 */ + <1 0 1 1>, /* 2: VIDEO 1 */ + <1 0 2 2>, /* 3: VIDEO IC 0 */ + <1 0 3 3>, /* 4: VIDEO IC 1 */ + <1 0 4 4>, /* 5: IIC MAIN */ + <1 0 6 6>, /* 6: IIC VIDEO 0 */ + <1 0 7 7>, /* 7: IIC VIDEO 1 */ + <1 1 0 0>, /* 8: OSD 0 */ + <1 1 1 1>, /* 9: OSD 1 */ + <1 1 2 2>, /* 10: SPDIF 0 */ + <1 1 3 3>, /* 11: SPDIF 1 */ + <1 0 12 12>, /* 12: COMM 0 */ + <1 0 13 13>, /* 13: COMM 1 */ + <1 0 10 10>, /* 14: COMM 2 */ + <1 0 11 11>, /* 15: COMM 3 */ + <2 0 5 5>, /* 16: MDIO */ + <1 0 8 8>, /* 17: PHY */ + <1 1 4 4>, /* 18: RS232 */ + <1 1 5 5>, /* 19: AUDIO */ + <1 1 8 8>, /* 20: PROC_AUDIO */ + <1 1 7 7>, /* 21: USB/ETH-UART INT */ + <2 1 10 10>, /* 22: AXI Bridge 0 */ + <2 1 11 11>, /* 23: AXI Bridge 1 */ + <2 1 9 9>, /* 24: USB/ETH-Secondary IIC */ + <>; +}; + +/ { + FPGA0BUS: fpga0bus { + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 0x00002000>; + + compatible = "gdsys,soc"; + + fpga0_rs232 { + compatible = "gdsys,ihs_trans_rs232"; + reg = <0x50 0x08>; + little-endian; + }; + + fpga0_uart_usb { + compatible = "gdsys,ihs_simple_uart"; + reg = <0xa0 0x08>; + little-endian; + fpga_interrupts = <21>; + line = <0>; + }; + + fpga0_iic_main { + compatible = "gdsys,ihs_i2cmaster"; + reg = <0x60 0x10>; + little-endian; + fpga_interrupts = <5>; + #address-cells = <1>; + #size-cells = <0>; + + fpga0_dp_video0_redriver: fpga0_dp_video0_redriver { + compatible = "ti,sn75dp130"; + reg = <0x2c>; + eq-i2c-enable = <3 2 1 0 + 3 2 1 0 + 3 2 1 0 + 3 2 1 0>; /* 3.5 dB for all pe values for all lanes */ + }; + fpga0_dp_video1_redriver: fpga0_dp_video1_redriver { + compatible = "ti,sn75dp130"; + reg = <0x2e>; + eq-i2c-enable = <3 2 1 0 + 3 2 1 0 + 3 2 1 0 + 3 2 1 0>; /* 3.5 dB for all pe values for all lanes */ + }; + lm77@48 { + compatible = "national,lm77"; + reg = <0x48>; + }; + ads1015@49 { + compatible = "ti,ads1015"; + reg = <0x49>; + }; + ads1015@4b { + compatible = "ti,ads1015"; + reg = <0x4b>; + }; + }; + + fpga0_video0 { + compatible = "gdsys,ihs_video_out"; + reg = <0x100 0x40>; + little-endian; + fpga_interrupts = <1 8>; /* VIDEO OSD */ + osd_base = <0x180>; + osd_buffer_base = <0x1000>; + spdif_audio_base = <0x1e0>; + video_index = <0>; + video_id = <0>; + fpga-force-pos-pol; + sync-source; + fpga-pb-pixels = <2730>; /* 8192 / 3 */ + fpga-ra-lines = <2>; + video_tx = <&fpga0_dp_video0>; + clk_gen = <&fpga0_video0_clkgen>; + ddc_ci = <&fpga0_dp_video0>; + }; + + fpga0_iic_video0 { + compatible = "gdsys,ihs_i2cmaster"; + reg = <0x1c0 0x10>; + little-endian; + fpga_interrupts = <6>; + #address-cells = <1>; + #size-cells = <0>; + + fpga0_video0_clkgen: fpga0_video0_clkgen { + compatible = "idt,ics8n3qv01"; + reg = <0x6e>; + channel = <0>; + }; + }; + + fpga0_axi_video0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "gdsys,ihs_axi"; + reg = <0x170 0x10>; + little-endian; + fpga_interrupts = <22>; + + fpga0_dp_video0: fpga0_dp_video0 { + compatible = "gdsys,logicore_dp_tx"; + reg = <0x44a10000 0x1000>; + little-endian; + redriver = <&fpga0_dp_video0_redriver>; + video_id = <0>; + }; + }; + + fpga0_video1 { + compatible = "gdsys,ihs_video_out"; + reg = <0x200 0x40>; + little-endian; + fpga_interrupts = <2 9>; /* VIDEO OSD */ + osd_base = <0x280>; + osd_buffer_base = <0x2000>; + spdif_audio_base = <0x2e0>; + video_index = <1>; + video_id = <1>; + fpga-force-pos-pol; + sync-source; + fpga-pb-pixels = <2730>; /* 8192 / 3 */ + fpga-ra-lines = <2>; + video_tx = <&fpga0_dp_video1>; + clk_gen = <&fpga0_video1_clkgen>; + ddc_ci = <&fpga0_dp_video1>; + }; + + fpga0_iic_video1 { + compatible = "gdsys,ihs_i2cmaster"; + reg = <0x2c0 0x10>; + little-endian; + fpga_interrupts = <7>; + #address-cells = <1>; + #size-cells = <0>; + + fpga0_video1_clkgen: fpga0_video1_clkgen { + compatible = "idt,ics8n3qv01"; + reg = <0x6e>; + channel = <1>; + }; + }; + + fpga0_axi_video1 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "gdsys,ihs_axi"; + reg = <0x270 0x10>; + little-endian; + fpga_interrupts = <23>; + + fpga0_dp_video1: fpga0_dp_video1 { + compatible = "gdsys,logicore_dp_tx"; + reg = <0x44a10000 0x1000>; + little-endian; + redriver = <&fpga0_dp_video1_redriver>; + video_id = <1>; + }; + }; + + fpga0_iic_usb { + compatible = "gdsys,ihs_i2cmaster"; + reg = <0xb0 0x10>; + little-endian; + fpga_interrupts = <24>; + #address-cells = <1>; + #size-cells = <0>; + + pca9555@20 { + compatible = "nxp,pca9555"; + reg = <0x20>; + #gpio-cells = <2>; + gpio-controller; + }; + }; + + fpga0_ep0 { + compatible = "gdsys,io-endpoint"; + reg = < 0x020 0x10 + 0x320 0x10 + 0x340 0x10 + 0x360 0x10>; + little-endian; + irq-model-local; + fpga_interrupts = <12 13 14 15>; + pollcycle = <200>; + nprot_channel = <16>; + uart_line = <0>; + ep_index = <0>; + line_protocol = <1>; + }; + + fpga0_mdio { + compatible = "gdsys,ihs_mdiomaster"; + reg = <0x0058 0x10>; + little-endian; + fpga_interrupts = <16>; + #address-cells = <1>; + #size-cells = <0>; + + fpga0_phy0 { + compatible = "ethernet-phy-ieee802.3-c45"; + device_type ="ethernet-phy"; + reg = <0>; + }; + fpga0_phy1 { + compatible = "ethernet-phy-ieee802.3-c45"; + device_type ="ethernet-phy"; + reg = <1>; + }; + fpga0_phy2 { + compatible = "ethernet-phy-ieee802.3-c45"; + device_type ="ethernet-phy"; + reg = <2>; + }; + fpga0_phy3 { + compatible = "ethernet-phy-ieee802.3-c45"; + device_type ="ethernet-phy"; + reg = <3>; + }; + }; + + }; + + + FPGA1BUS: fpga1bus { + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 0x00002000>; + + compatible = "gdsys,soc"; + + fpga1_uart_usb { + compatible = "gdsys,ihs_simple_uart"; + reg = <0xa0 0x08>; + little-endian; + fpga_interrupts = <21>; + line = <4>; /* TODO check and FIX */ + }; + + fpga1_iic_main { + compatible = "gdsys,ihs_i2cmaster"; + reg = <0x60 0x10>; + little-endian; + fpga_interrupts = <5>; + #address-cells = <1>; + #size-cells = <0>; + + fpga1_dp_video0_redriver: fpga1_dp_video0_redriver { + compatible = "ti,sn75dp130"; + reg = <0x2c>; + eq-i2c-enable = <3 2 1 0 + 3 2 1 0 + 3 2 1 0 + 3 2 1 0>; /* 3.5 dB for all pe values for all lanes */ + }; + fpga1_dp_video1_redriver: fpga1_dp_video1_redriver { + compatible = "ti,sn75dp130"; + reg = <0x2e>; + eq-i2c-enable = <3 2 1 0 + 3 2 1 0 + 3 2 1 0 + 3 2 1 0>; /* 3.5 dB for all pe values for all lanes */ + }; + lm77@48 { + compatible = "national,lm77"; + reg = <0x48>; + }; + ads1015@49 { + compatible = "ti,ads1015"; + reg = <0x49>; + }; + ads1015@4b { + compatible = "ti,ads1015"; + reg = <0x4b>; + }; + }; + + fpga1_video0 { + compatible = "gdsys,ihs_video_out"; + reg = <0x100 0x40>; + little-endian; + fpga_interrupts = <1 8>; /* VIDEO OSD */ + osd_base = <0x180>; + osd_buffer_base = <0x1000>; + spdif_audio_base = <0x1e0>; + video_index = <0>; + video_id = <4>; + fpga-force-pos-pol; + sync-source; + fpga-pb-pixels = <2730>; /* 8192 / 3 */ + fpga-ra-lines = <2>; + video_tx = <&fpga1_dp_video0>; + clk_gen = <&fpga1_video0_clkgen>; + ddc_ci = <&fpga1_dp_video0>; + }; + + fpga1_iic_video0 { + compatible = "gdsys,ihs_i2cmaster"; + reg = <0x1c0 0x10>; + little-endian; + fpga_interrupts = <6>; + #address-cells = <1>; + #size-cells = <0>; + + fpga1_video0_clkgen: fpga1_video0_clkgen { + compatible = "idt,ics8n3qv01"; + reg = <0x6e>; + channel = <4>; + }; + }; + + fpga1_axi_video0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "gdsys,ihs_axi"; + reg = <0x170 0x10>; + little-endian; + fpga_interrupts = <22>; + + fpga1_dp_video0: fpga1_dp_video0 { + compatible = "gdsys,logicore_dp_tx"; + reg = <0x44a10000 0x1000>; + little-endian; + redriver = <&fpga1_dp_video0_redriver>; + video_id = <4>; + }; + }; + + fpga1_video1 { + compatible = "gdsys,ihs_video_out"; + reg = <0x200 0x40>; + little-endian; + fpga_interrupts = <2 9>; /* VIDEO OSD */ + osd_base = <0x280>; + osd_buffer_base = <0x2000>; + spdif_audio_base = <0x2e0>; + video_index = <1>; + video_id = <5>; + fpga-force-pos-pol; + sync-source; + fpga-pb-pixels = <2730>; /* 8192 / 3 */ + fpga-ra-lines = <2>; + video_tx = <&fpga1_dp_video1>; + clk_gen = <&fpga1_video1_clkgen>; + ddc_ci = <&fpga1_dp_video1>; + }; + + fpga1_iic_video1 { + compatible = "gdsys,ihs_i2cmaster"; + reg = <0x2c0 0x10>; + little-endian; + fpga_interrupts = <7>; + #address-cells = <1>; + #size-cells = <0>; + + fpga1_video1_clkgen: fpga1_video1_clkgen { + compatible = "idt,ics8n3qv01"; + reg = <0x6e>; + channel = <5>; + }; + }; + + fpga1_axi_video1 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "gdsys,ihs_axi"; + reg = <0x270 0x10>; + little-endian; + fpga_interrupts = <23>; + + fpga1_dp_video1: fpga1_dp_video1 { + compatible = "gdsys,logicore_dp_tx"; + reg = <0x44a10000 0x1000>; + little-endian; + redriver = <&fpga1_dp_video1_redriver>; + video_id = <5>; + }; + }; + + fpga1_iic_usb { + compatible = "gdsys,ihs_i2cmaster"; + reg = <0xb0 0x10>; + little-endian; + fpga_interrupts = <24>; + #address-cells = <1>; + #size-cells = <0>; + + pca9555@20 { + compatible = "nxp,pca9555"; + reg = <0x20>; + #gpio-cells = <2>; + gpio-controller; + }; + }; + + fpga1_ep0 { + compatible = "gdsys,io-endpoint"; + reg = < 0x020 0x10 + 0x320 0x10 + 0x340 0x10 + 0x360 0x10>; + little-endian; + irq-model-local; + fpga_interrupts = <12 13 14 15>; + pollcycle = <200>; + nprot_channel = <17>; + uart_line = <1>; + ep_index = <0>; + line_protocol = <1>; + }; + + fpga1_mdio { + compatible = "gdsys,ihs_mdiomaster"; + reg = <0x0058 0x10>; + little-endian; + fpga_interrupts = <16>; + #address-cells = <1>; + #size-cells = <0>; + + fpga1_phy0 { + compatible = "ethernet-phy-ieee802.3-c45"; + device_type ="ethernet-phy"; + reg = <0>; + }; + fpga1_phy1 { + compatible = "ethernet-phy-ieee802.3-c45"; + device_type ="ethernet-phy"; + reg = <1>; + }; + fpga1_phy2 { + compatible = "ethernet-phy-ieee802.3-c45"; + device_type ="ethernet-phy"; + reg = <2>; + }; + fpga1_phy3 { + compatible = "ethernet-phy-ieee802.3-c45"; + device_type ="ethernet-phy"; + reg = <3>; + }; + }; + + }; + +}; + +#include "gdsys/gazerbeam-uboot.dtsi" diff --git a/arch/powerpc/dts/gdsys/gazerbeam-base.dtsi b/arch/powerpc/dts/gdsys/gazerbeam-base.dtsi new file mode 100644 index 0000000000..aca05f2cd0 --- /dev/null +++ b/arch/powerpc/dts/gdsys/gazerbeam-base.dtsi @@ -0,0 +1,185 @@ +/* + * Gazerbeam Device Tree Source + * + * (C) Copyright 2015 + * Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +/ { + model = "gdsys,gazerbeam"; + compatible = "fsl,mpc8308rdb"; + + aliases { + ethernet0 = &enet0; + ethernet1 = &enet1; + }; + + memory { + device_type = "memory"; + }; +}; + +&enet1 { + status = "okay"; +}; + +&IIC { + fsl,preserve-clocking; + + at97sc3205t@29 { + compatible = "atmel,at97sc3204t"; + reg = <0x29>; + }; + + lm77@48 { + compatible = "national,lm77"; + reg = <0x48>; + }; + + ads1015@49 { + compatible = "ti,ads1015"; + reg = <0x49>; + }; + + lm77@4a { + compatible = "national,lm77"; + reg = <0x4a>; + }; + + emc2305@2e { + compatible = "smsc,emc2305"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x2e>; + fan@0 { + reg = <0>; + }; + fan@1 { + reg = <1>; + }; + fan@2 { + reg = <2>; + }; + fan@3 { + reg = <3>; + }; + fan@4 { + reg = <4>; + }; + }; + + emc2305@4c { + compatible = "smsc,emc2305"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x4c>; + fan@0 { + reg = <0>; + }; + fan@1 { + reg = <1>; + }; + fan@2 { + reg = <2>; + }; + fan@3 { + reg = <3>; + }; + fan@4 { + reg = <4>; + }; + }; + + at24c512@54 { + compatible = "atmel,24c512"; + reg = <0x54>; + }; + + /* PPC-Board */ + pca9698@22 { + compatible = "nxp,pca9698"; + reg = <0x22>; + #gpio-cells = <2>; + gpio-controller; + }; + + /* IO-Board */ + pca9698@20 { + compatible = "nxp,pca9698"; + reg = <0x20>; + #gpio-cells = <2>; + gpio-controller; + }; +}; + +&IIC2 { + fsl,preserve-clocking; + + status = "okay"; + + /* MC2/SC-Board */ + GPIO_VB0: pca9698@20 { + compatible = "nxp,pca9698"; + reg = <0x20>; + #gpio-cells = <2>; + gpio-controller; + }; + + /* MC4-Board */ + GPIO_VB1: pca9698@22 { + compatible = "nxp,pca9698"; + reg = <0x22>; + #gpio-cells = <2>; + gpio-controller; + }; +}; + +&SPI { + gpios = < /*SPI-CSS-FPGA-U-FLASH#*/ &gpio0 8 0 + /*SPI-CSS-FPGA-O-FLASH#*/ &gpio0 6 0 + /*SPI-CSS-STDP1_U-FLASH#*/ &gpio0 12 0 + /*SPI-CSS-STDP2_U-FLASH#*/ &gpio0 11 0 + /*SPI-CSS-STDP1_O-FLASH#*/ &gpio0 15 0 + /*SPI-CSS-STDP2_O-FLASH#*/ &gpio0 3 0>; + + m25p16@0 { + compatible = "st,n25q128a11"; + reg = <0x0>; + spi-max-frequency = <20000000>; + }; + + m25p16@1 { + compatible = "st,n25q128a11"; + reg = <0x1>; + spi-max-frequency = <20000000>; + }; + + m25p16@2 { + compatible = "st,m25p40"; + reg = <0x2>; + spi-max-frequency = <20000000>; + }; + + m25p16@3 { + compatible = "st,m25p40"; + reg = <0x3>; + spi-max-frequency = <20000000>; + }; + + m25p16@4 { + compatible = "st,m25p40"; + reg = <0x4>; + spi-max-frequency = <20000000>; + }; + + m25p16@5 { + compatible = "st,m25p40"; + reg = <0x5>; + spi-max-frequency = <20000000>; + }; +}; diff --git a/arch/powerpc/dts/gdsys/gazerbeam-uboot.dtsi b/arch/powerpc/dts/gdsys/gazerbeam-uboot.dtsi new file mode 100644 index 0000000000..1c4977f20f --- /dev/null +++ b/arch/powerpc/dts/gdsys/gazerbeam-uboot.dtsi @@ -0,0 +1,250 @@ +#include <dt-bindings/memory/mpc83xx-sdram.h> +#include <dt-bindings/clk/mpc83xx-clk.h> + +/ { + aliases { + i2c0 = &IIC; + i2c1 = &IIC2; + i2c2 = "/fpga0bus/fpga0_iic_main"; + i2c3 = "/fpga0bus/fpga0_iic_video0"; + i2c4 = "/fpga0bus/fpga0_iic_video1"; + i2c5 = "/fpga0bus/fpga0_iic_usb"; + gdsys_soc0 = "/fpga0bus"; + gdsys_soc1 = "/fpga1bus"; + ioep0 = "/fpga0bus/fpga0_ep0"; + ioep1 = "/fpga0bus/fpga1_ep0"; + }; + + chosen { + stdout-path = &serial1; + }; + + cpus { + compatible = "cpu_bus"; + u-boot,dm-pre-reloc; + + PowerPC,8308@0 { + compatible = "fsl,mpc8308"; + clocks = <&socclocks MPC83XX_CLK_CORE + &socclocks MPC83XX_CLK_CSB>; + u-boot,dm-pre-reloc; + }; + }; + + board { + compatible = "gdsys,board_gazerbeam"; + csb = <&board_soc>; + serdes = <&SERDES>; + rxaui0 = <&RXAUI0_0>; + rxaui1 = <&RXAUI0_1>; + rxaui2 = <&RXAUI0_2>; + rxaui3 = <&RXAUI0_3>; + rxaui4 = <&RXAUI1_0>; + rxaui5 = <&RXAUI1_1>; + rxaui6 = <&RXAUI1_2>; + rxaui7 = <&RXAUI1_3>; + fpga0 = <&FPGA0>; + fpga1 = <&FPGA1>; + ioep0 = <&IOEP0>; + ioep1 = <&IOEP1>; + + ver-gpios = <&PPCPCA 12 0 + &PPCPCA 13 0 + &PPCPCA 14 0 + &PPCPCA 15 0>; + + /* MC2/SC-Board */ + var-gpios-mc2 = <&GPIO_VB0 0 0 /* VAR-MC_SC */ + &GPIO_VB0 11 0>; /* VAR-CON */ + /* MC4-Board */ + var-gpios-mc4 = <&GPIO_VB1 0 0 /* VAR-MC_SC */ + &GPIO_VB1 11 0>; /* VAR-CON */ + + reset-gpios = <&gpio0 1 0 &gpio0 2 1>; + }; + + socclocks: clocks { + compatible = "fsl,mpc8308-clk"; + #clock-cells = <1>; + u-boot,dm-pre-reloc; + }; + + timer { + compatible = "fsl,mpc83xx-timer"; + clocks = <&socclocks MPC83XX_CLK_CSB>; + }; +}; + +&FPGA0 { + reset-gpios = <&PPCPCA 26 0>; + done-gpios = <&GPIO_VB0 19 0>; +}; + +&FPGA1 { + status = "disable"; +}; + +&FPGA0BUS { + ranges = <0x0 0xe0600000 0x00004000>; + fpga = <&FPGA0>; + + fpga0_video0 { + mode = "640_480_60"; + + status = "disabled"; + }; + + RXAUI0_0: fpga0_rxaui@fc0 { + compatible = "gdsys,rxaui_ctrl"; + reg = <0x0fc0 0x10>; + }; + + fpga0_iic_video0 { + status = "disabled"; + }; + + fpga0_axi_video0 { + status = "disabled"; + }; + + fpga0_video1 { + mode = "640_480_60"; + status = "disabled"; + }; + + fpga0_iic_video1 { + status = "disabled"; + }; + + fpga0_axi_video1 { + status = "disabled"; + }; + + IOEP0: fpga0_ep0 { + }; + + RXAUI0_1: fpga0_rxaui@fd0 { + compatible = "gdsys,rxaui_ctrl"; + reg = <0x0fd0 0x10>; + }; + + RXAUI0_2: fpga0_rxaui@fe0 { + compatible = "gdsys,rxaui_ctrl"; + reg = <0x0fe0 0x10>; + }; + + RXAUI0_3: fpga0_rxaui@ff0 { + compatible = "gdsys,rxaui_ctrl"; + reg = <0x0ff0 0x10>; + }; +}; + +&FPGA1BUS { + ranges = <0x0 0xe0700000 0x00004000>; + fpga = <&FPGA1>; + + status = "disable"; + + fpga1_video0 { + mode = "640_480_60"; + }; + + RXAUI1_0: fpga0_rxaui@fc0 { + compatible = "gdsys,rxaui_ctrl"; + reg = <0x0fc0 0x10>; + }; + + fpga1_video1 { + mode = "640_480_60"; + }; + + IOEP1: fpga1_ep0 { + }; + + RXAUI1_1: fpga0_rxaui@fd0 { + compatible = "gdsys,rxaui_ctrl"; + reg = <0x0fd0 0x10>; + }; + + RXAUI1_2: fpga0_rxaui@fe0 { + compatible = "gdsys,rxaui_ctrl"; + reg = <0x0fe0 0x10>; + }; + + RXAUI1_3: fpga0_rxaui@ff0 { + compatible = "gdsys,rxaui_ctrl"; + reg = <0x0ff0 0x10>; + }; +}; + +&board_soc { + u-boot,dm-pre-reloc; + clocks = <&socclocks MPC83XX_CLK_CSB>; + + memory@2000 { + u-boot,dm-pre-reloc; + }; + + sdhc@2e000 { + clocks = <&socclocks MPC83XX_CLK_SDHC>; + clock-names = "per"; + }; + + SERDES: serdes@e3000 { + reg = <0xe3000 0x200>; + compatible = "fsl,mpc83xx-serdes"; + proto = "pex"; + serdes-clk = <100>; + vdd; + }; +}; + +&IIC { + clocks = <&socclocks MPC83XX_CLK_I2C1>; + + PPCPCA: pca9698@20 { + label = "ppc"; + }; + + IOPCA: pca9698@22 { + label = "io"; + }; + + at97sc3205t@29 { + u-boot,i2c-offset-len = <0>; + }; +}; + +&IIC2 { + clocks = <&socclocks MPC83XX_CLK_I2C2>; + + GPIO_VB0: pca9698@20 { + label = "mc2-sc"; + }; + + GPIO_VB1: pca9698@22 { + label = "mc4"; + }; +}; + +&board_soc { + u-boot,dm-pre-reloc; +}; + +&GPIO_VB0 { + u-boot,dm-pre-reloc; +}; + +&serial0 { + clocks = <&socclocks MPC83XX_CLK_CSB>; + u-boot,dm-pre-reloc; +}; + +&serial1 { + clocks = <&socclocks MPC83XX_CLK_CSB>; + u-boot,dm-pre-reloc; +}; + +&pci0 { + clocks = <&socclocks MPC83XX_CLK_PCIEXP1>; +}; diff --git a/arch/powerpc/dts/gdsys/mpc8308.dtsi b/arch/powerpc/dts/gdsys/mpc8308.dtsi new file mode 100644 index 0000000000..23e7403d91 --- /dev/null +++ b/arch/powerpc/dts/gdsys/mpc8308.dtsi @@ -0,0 +1,354 @@ +/* + * Basic platform for gdsys mpc8308 based devices + * + * (C) Copyright 2014 + * Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de + * + * based on mpc8308rdb + * Copyright 2009 Freescale Semiconductor Inc. + * Copyright 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +/dts-v1/; + +#include <dt-bindings/memory/mpc83xx-sdram.h> + +/ { + compatible = "fsl,mpc8308rdb"; + + #address-cells = <1>; + #size-cells = <1>; + + aliases { + serial0 = &serial0; + serial1 = &serial1; + }; + + memory { + device_type = "memory"; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + PowerPC,8308@0 { + device_type = "cpu"; + reg = <0x0>; + d-cache-line-size = <32>; + i-cache-line-size = <32>; + d-cache-size = <16384>; + i-cache-size = <16384>; + timebase-frequency = <0>; // from bootloader + bus-frequency = <0>; // from bootloader + clock-frequency = <0>; // from bootloader + }; + }; + + board_lbc: localbus@e0005000 { + #address-cells = <2>; + #size-cells = <1>; + compatible = "fsl,mpc8315-elbc", "fsl,elbc", "simple-bus"; + reg = <0xe0005000 0x1000>; + interrupts = <77 0x8>; + interrupt-parent = <&ipic>; + }; + + board_soc: immr@e0000000 { + #address-cells = <1>; + #size-cells = <1>; + device_type = "soc"; + compatible = "fsl,mpc8308-immr", "simple-bus"; + ranges = <0 0xe0000000 0x00100000>; + reg = <0xe0000000 0x00000200>; + bus-frequency = <0>; + + wdt@200 { + device_type = "watchdog"; + compatible = "mpc83xx_wdt"; + reg = <0x200 0x100>; + }; + + memory@2000 { + #address-cells = <2>; + #size-cells = <1>; + compatible = "fsl,mpc83xx-mem-controller"; + reg = <0x2000 0x1000>; + device_type = "memory"; + + driver_software_override = <DSO_ENABLE>; + p_impedance_override = <DSO_P_IMPEDANCE_NOMINAL>; + n_impedance_override = <DSO_N_IMPEDANCE_NOMINAL>; + odt_termination_value = <ODT_TERMINATION_150_OHM>; + ddr_type = <DDR_TYPE_DDR2_1_8_VOLT>; + + clock_adjust = <CLOCK_ADJUST_05>; + + read_to_write = <0>; + write_to_read = <0>; + read_to_read = <0>; + write_to_write = <0>; + active_powerdown_exit = <2>; + precharge_powerdown_exit = <6>; + odt_powerdown_exit = <8>; + mode_reg_set_cycle = <2>; + + precharge_to_activate = <2>; + activate_to_precharge = <6>; + activate_to_readwrite = <2>; + mcas_latency = <CASLAT_40>; + refresh_recovery = <17>; + last_data_to_precharge = <2>; + activate_to_activate = <2>; + last_write_data_to_read = <2>; + + additive_latency = <0>; + mcas_to_preamble_override = <READ_LAT_PLUS_1_2>; + write_latency = <3>; + read_to_precharge = <2>; + write_cmd_to_write_data = <CLOCK_DELAY_1_2>; + minimum_cke_pulse_width = <3>; + four_activates_window = <5>; + + self_refresh = <SREN_ENABLE>; + sdram_type = <TYPE_DDR2>; + databus_width = <DATA_BUS_WIDTH_32>; + + force_self_refresh = <MODE_NORMAL>; + dll_reset = <DLL_RESET_ENABLE>; + dqs_config = <DQS_TRUE>; + odt_config = <ODT_ASSERT_READS>; + posted_refreshes = <1>; + + refresh_interval = <2084>; + precharge_interval = <256>; + + sdmode = <0x0242>; + esdmode = <0x0440>; + + ram@0 { + reg = <0x0 0x0 0x8000000>; + compatible = "nanya,nt5tu64m16hg"; + + odt_rd_cfg = <ODT_RD_NEVER>; + odt_wr_cfg = <ODT_WR_ONLY_CURRENT>; + bank_bits = <3>; + row_bits = <13>; + col_bits = <10>; + }; + }; + + IIC:i2c@3000 { + #address-cells = <1>; + #size-cells = <0>; + cell-index = <0>; + compatible = "fsl-i2c"; + reg = <0x3000 0x100>; + interrupts = <14 0x8>; + interrupt-parent = <&ipic>; + dfsrr; + }; + + IIC2: i2c@3100 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl-i2c"; + reg = <0x3100 0x100>; + interrupts = <15 0x8>; + interrupt-parent = <&ipic>; + dfsrr; + status = "disabled"; + }; + + SPI:spi@7000 { + #address-cells = <1>; + #size-cells = <0>; + cell-index = <0>; + compatible = "fsl,spi"; + reg = <0x7000 0x1000>; + interrupts = <16 0x8>; + interrupt-parent = <&ipic>; + mode = "cpu"; + }; + + sdhc@2e000 { + compatible = "fsl,esdhc", "fsl,mpc8308-esdhc"; + reg = <0x2e000 0x1000>; + interrupts = <42 0x8>; + interrupt-parent = <&ipic>; + sdhci,auto-cmd12; + /* Filled in by U-Boot */ + clock-frequency = <0>; + }; + + serial0: serial@4500 { + cell-index = <0>; + device_type = "serial"; + compatible = "fsl,ns16550", "ns16550"; + reg = <0x4500 0x100>; + clock-frequency = <133333333>; + interrupts = <9 0x8>; + interrupt-parent = <&ipic>; + }; + + serial1: serial@4600 { + cell-index = <1>; + device_type = "serial"; + compatible = "fsl,ns16550", "ns16550"; + reg = <0x4600 0x100>; + clock-frequency = <133333333>; + interrupts = <10 0x8>; + interrupt-parent = <&ipic>; + }; + + gpio0: gpio@c00 { + #gpio-cells = <2>; + device_type = "gpio"; + compatible = "fsl,mpc8308-gpio", "fsl,mpc8349-gpio"; + reg = <0xc00 0x18>; + interrupts = <74 0x8>; + interrupt-parent = <&ipic>; + gpio-controller; + }; + + /* IPIC + * interrupts cell = <intr #, sense> + * sense values match linux IORESOURCE_IRQ_* defines: + * sense == 8: Level, low assertion + * sense == 2: Edge, high-to-low change + */ + ipic: interrupt-controller@700 { + compatible = "fsl,ipic"; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <2>; + reg = <0x700 0x100>; + device_type = "ipic"; + }; + + ipic-msi@7c0 { + compatible = "fsl,ipic-msi"; + reg = <0x7c0 0x40>; + msi-available-ranges = <0x0 0x100>; + interrupts = < 0x43 0x8 + 0x4 0x8 + 0x51 0x8 + 0x52 0x8 + 0x56 0x8 + 0x57 0x8 + 0x58 0x8 + 0x59 0x8 >; + interrupt-parent = < &ipic >; + }; + + dma@2c000 { + compatible = "fsl,mpc8308-dma", "fsl,mpc5121-dma"; + reg = <0x2c000 0x1800>; + interrupts = <3 0x8 + 94 0x8>; + interrupt-parent = < &ipic >; + }; + + enet0: ethernet@24000 { + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x24000 0x1000>; + + cell-index = <0>; + device_type = "network"; + model = "eTSEC"; + compatible = "gianfar", "fsl,tsec"; + reg = <0x24000 0x1000>; + local-mac-address = [ 00 00 00 00 00 00 ]; + interrupts = <32 0x8 33 0x8 34 0x8>; + interrupt-parent = <&ipic>; + tbi-handle = < &tbi0 >; + phy-handle = < &phy1 >; + fsl,magic-packet; + + mdio@520 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,gianfar-mdio"; + reg = <0x520 0x20>; + phy1: ethernet-phy@1 { + reg = <0x1>; + }; + phy2: ethernet-phy@0 { + reg = <0x0>; + device_type = "ethernet-phy"; + }; + tbi0: tbi-phy@11 { + reg = <0x11>; + device_type = "tbi-phy"; + }; + }; + }; + + enet1: ethernet@25000 { + #address-cells = <1>; + #size-cells = <1>; + cell-index = <1>; + device_type = "network"; + model = "eTSEC"; + compatible = "gianfar", "fsl,tsec"; + reg = <0x25000 0x1000>; + ranges = <0x0 0x25000 0x1000>; + local-mac-address = [ 00 00 00 00 00 00 ]; + interrupts = <35 0x8 36 0x8 37 0x8>; + interrupt-parent = <&ipic>; + phy-handle = < &phy2 >; + status = "disabled"; + + mdio@520 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,gianfar-tbi"; + reg = <0x520 0x20>; + tbi1: tbi-phy@11 { + reg = <0x11>; + device_type = "tbi-phy"; + }; + }; + }; + }; + + pci0: pcie@e0009000 { + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + device_type = "pci"; + compatible = "fsl,mpc8308-pcie", "fsl,mpc8314-pcie"; + reg = <0xe0009000 0x00001000 + 0xb0000000 0x01000000>; + ranges = <0x02000000 0 0xa0000000 0xa0000000 0 0x10000000 + 0x01000000 0 0x00000000 0xb1000000 0 0x00800000>; + bus-range = <0 0>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = <0 0 0 1 &ipic 1 8 + 0 0 0 2 &ipic 1 8 + 0 0 0 3 &ipic 1 8 + 0 0 0 4 &ipic 1 8>; + interrupts = <0x1 0x8>; + interrupt-parent = <&ipic>; + clock-frequency = <0>; + + pcie@0 { + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + reg = <0 0 0 0 0>; + ranges = <0x02000000 0 0xa0000000 + 0x02000000 0 0xa0000000 + 0 0x10000000 + 0x01000000 0 0x00000000 + 0x01000000 0 0x00000000 + 0 0x00800000>; + }; + }; +}; diff --git a/arch/powerpc/dts/gdsys/soc/i2c/cirrus-audio-codec.dtsi b/arch/powerpc/dts/gdsys/soc/i2c/cirrus-audio-codec.dtsi new file mode 100644 index 0000000000..9787e09648 --- /dev/null +++ b/arch/powerpc/dts/gdsys/soc/i2c/cirrus-audio-codec.dtsi @@ -0,0 +1,6 @@ +&IIC { + cs4265@4f { + compatible = "cirrus,cs4265"; + reg = <0x0000004f>; + }; +}; diff --git a/arch/powerpc/dts/gdsys/soc/i2c/dallas-rtc.dtsi b/arch/powerpc/dts/gdsys/soc/i2c/dallas-rtc.dtsi new file mode 100644 index 0000000000..336bdcaf2e --- /dev/null +++ b/arch/powerpc/dts/gdsys/soc/i2c/dallas-rtc.dtsi @@ -0,0 +1,6 @@ +&IIC { + ds1339@68 { + compatible = "dallas,ds1339"; + reg = <0x68>; + }; +}; diff --git a/arch/powerpc/dts/gdsys/soc/lbc/gazerbeam.dtsi b/arch/powerpc/dts/gdsys/soc/lbc/gazerbeam.dtsi new file mode 100644 index 0000000000..5ff58c28e5 --- /dev/null +++ b/arch/powerpc/dts/gdsys/soc/lbc/gazerbeam.dtsi @@ -0,0 +1,5 @@ +&board_lbc { + ranges = <0x0 0x0 0xfe000000 0x00800000 + 0x1 0x0 0xe0600000 0x00003000 + 0x2 0x0 0xe0700000 0x00003000>; +}; diff --git a/arch/powerpc/dts/gdsys/soc/nor/flash-80k-partition.dtsi b/arch/powerpc/dts/gdsys/soc/nor/flash-80k-partition.dtsi new file mode 100644 index 0000000000..c6cc1409e0 --- /dev/null +++ b/arch/powerpc/dts/gdsys/soc/nor/flash-80k-partition.dtsi @@ -0,0 +1,20 @@ +&board_lbc { + flash@0,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "cfi-flash"; + reg = <0x0 0x0 0x100000>; + bank-width = <2>; + device-width = <1>; + + u-boot@0 { + reg = <0x0 0x80000>; + }; + env@80000 { + reg = <0x80000 0x10000>; + }; + env1@90000 { + reg = <0x90000 0x10000>; + }; + }; +}; diff --git a/arch/powerpc/include/asm/arch-mpc83xx/clock.h b/arch/powerpc/include/asm/arch-mpc83xx/clock.h new file mode 100644 index 0000000000..d57e93c2df --- /dev/null +++ b/arch/powerpc/include/asm/arch-mpc83xx/clock.h @@ -0,0 +1,22 @@ +/* + * (C) Copyright 2018 + * Mario Six, Guntermann & Drunck GmbH, mario.six@gdsys.cc + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __ASM_POWERPC_CLOCK_H +#define __ASM_POWERPC_CLOCK_H + +/* Make fsl_esdhc driver happy */ +enum mxc_clock { + MXC_ESDHC_CLK, +}; + +DECLARE_GLOBAL_DATA_PTR; + +uint mxc_get_clock(int clk) +{ + return gd->arch.sdhc_clk; +} +#endif /* __ASM_POWERPC_CLOCK_H */ diff --git a/arch/powerpc/include/asm/arch-mpc83xx/gpio.h b/arch/powerpc/include/asm/arch-mpc83xx/gpio.h index 57f783ba14..385d651d20 100644 --- a/arch/powerpc/include/asm/arch-mpc83xx/gpio.h +++ b/arch/powerpc/include/asm/arch-mpc83xx/gpio.h @@ -6,10 +6,10 @@ /* * The MCP83xx's 1-2 GPIO controllers each with 32 bits. */ -#if defined(CONFIG_MPC8313) || defined(CONFIG_MPC8308) || \ - defined(CONFIG_MPC8315) +#if defined(CONFIG_ARCH_MPC8313) || defined(CONFIG_ARCH_MPC8308) || \ + defined(CONFIG_ARCH_MPC8315) #define MPC83XX_GPIO_CTRLRS 1 -#elif defined(CONFIG_MPC834x) || defined(CONFIG_MPC837x) +#elif defined(CONFIG_ARCH_MPC834X) || defined(CONFIG_ARCH_MPC837X) #define MPC83XX_GPIO_CTRLRS 2 #else #define MPC83XX_GPIO_CTRLRS 0 @@ -17,7 +17,15 @@ #define MAX_NUM_GPIOS (32 * MPC83XX_GPIO_CTRLRS) +struct mpc8xxx_gpio_plat { + ulong addr; + unsigned long size; + uint ngpios; +}; + +#ifndef DM_GPIO void mpc83xx_gpio_init_f(void); void mpc83xx_gpio_init_r(void); +#endif /* DM_GPIO */ #endif /* MPC83XX_GPIO_H_ */ diff --git a/arch/powerpc/include/asm/fsl_lbc.h b/arch/powerpc/include/asm/fsl_lbc.h index b076d5e838..bf352d9a56 100644 --- a/arch/powerpc/include/asm/fsl_lbc.h +++ b/arch/powerpc/include/asm/fsl_lbc.h @@ -43,10 +43,10 @@ void lbc_sdram_init(void); #define BR_MSEL 0x000000E0 #define BR_MSEL_SHIFT 5 #define BR_MS_GPCM 0x00000000 /* GPCM */ -#if !defined(CONFIG_MPC834x) && !defined(CONFIG_MPC8360) +#if !defined(CONFIG_ARCH_MPC834X) && !defined(CONFIG_ARCH_MPC8360) #define BR_MS_FCM 0x00000020 /* FCM */ #endif -#if defined(CONFIG_MPC834x) || defined(CONFIG_MPC8360) +#if defined(CONFIG_ARCH_MPC834X) || defined(CONFIG_ARCH_MPC8360) #define BR_MS_SDRAM 0x00000060 /* SDRAM */ #elif defined(CONFIG_MPC85xx) #define BR_MS_SDRAM 0x00000000 /* SDRAM */ @@ -54,7 +54,7 @@ void lbc_sdram_init(void); #define BR_MS_UPMA 0x00000080 /* UPMA */ #define BR_MS_UPMB 0x000000A0 /* UPMB */ #define BR_MS_UPMC 0x000000C0 /* UPMC */ -#if !defined(CONFIG_MPC834x) +#if !defined(CONFIG_ARCH_MPC834X) #define BR_ATOM 0x0000000C #define BR_ATOM_SHIFT 2 #endif @@ -67,7 +67,7 @@ void lbc_sdram_init(void); #define UPMB 1 #define UPMC 2 -#if defined(CONFIG_MPC834x) +#if defined(CONFIG_ARCH_MPC834X) #define BR_RES ~(BR_BA | BR_PS | BR_DECC | BR_WP | BR_MSEL | BR_V) #else #define BR_RES ~(BR_BA | BR_PS | BR_DECC | BR_WP | BR_MSEL | BR_ATOM | BR_V) @@ -133,7 +133,7 @@ void lbc_sdram_init(void); #define OR_GPCM_EHTR_SHIFT 1 #define OR_GPCM_EHTR_CLEAR 0x00000000 #define OR_GPCM_EHTR_SET 0x00000002 -#if !defined(CONFIG_MPC8308) +#if !defined(CONFIG_ARCH_MPC8308) #define OR_GPCM_EAD 0x00000001 #define OR_GPCM_EAD_SHIFT 0 #endif @@ -428,14 +428,17 @@ void lbc_sdram_init(void); #define LSDMR_BSMA1516 (3 << (31 - 10)) #define LSDMR_BSMA1617 (4 << (31 - 10)) #define LSDMR_RFCR5 (3 << (31 - 16)) +#define LSDMR_RFCR8 (5 << (31 - 16)) #define LSDMR_RFCR16 (7 << (31 - 16)) #define LSDMR_PRETOACT3 (3 << (31 - 19)) +#define LSDMR_PRETOACT6 (5 << (31 - 19)) #define LSDMR_PRETOACT7 (7 << (31 - 19)) #define LSDMR_ACTTORW3 (3 << (31 - 22)) #define LSDMR_ACTTORW7 (7 << (31 - 22)) #define LSDMR_ACTTORW6 (6 << (31 - 22)) #define LSDMR_BL8 (1 << (31 - 23)) #define LSDMR_WRC2 (2 << (31 - 27)) +#define LSDMR_WRC3 (3 << (31 - 27)) #define LSDMR_WRC4 (0 << (31 - 27)) #define LSDMR_BUFCMD (1 << (31 - 29)) #define LSDMR_CL3 (3 << (31 - 31)) diff --git a/arch/powerpc/include/asm/global_data.h b/arch/powerpc/include/asm/global_data.h index d00cee95fb..b6e4dd6c80 100644 --- a/arch/powerpc/include/asm/global_data.h +++ b/arch/powerpc/include/asm/global_data.h @@ -35,35 +35,35 @@ struct arch_global_data { #else /* There are other clocks in the MPC83XX */ u32 csb_clk; -# if defined(CONFIG_MPC8308) || defined(CONFIG_MPC831x) || \ - defined(CONFIG_MPC834x) || defined(CONFIG_MPC837x) +# if defined(CONFIG_ARCH_MPC8308) || defined(CONFIG_ARCH_MPC831X) || \ + defined(CONFIG_ARCH_MPC834X) || defined(CONFIG_ARCH_MPC837X) u32 tsec1_clk; u32 tsec2_clk; u32 usbdr_clk; -# elif defined(CONFIG_MPC8309) +# elif defined(CONFIG_ARCH_MPC8309) u32 usbdr_clk; # endif -# if defined(CONFIG_MPC834x) +# if defined(CONFIG_ARCH_MPC834X) u32 usbmph_clk; -# endif /* CONFIG_MPC834x */ -# if defined(CONFIG_MPC8315) +# endif /* CONFIG_ARCH_MPC834X */ +# if defined(CONFIG_ARCH_MPC8315) u32 tdm_clk; # endif u32 core_clk; u32 enc_clk; u32 lbiu_clk; u32 lclk_clk; -# if defined(CONFIG_MPC8308) || defined(CONFIG_MPC831x) || \ - defined(CONFIG_MPC837x) +# if defined(CONFIG_ARCH_MPC8308) || defined(CONFIG_ARCH_MPC831X) || \ + defined(CONFIG_ARCH_MPC837X) u32 pciexp1_clk; u32 pciexp2_clk; # endif -# if defined(CONFIG_MPC837x) || defined(CONFIG_MPC8315) +# if defined(CONFIG_ARCH_MPC837X) || defined(CONFIG_ARCH_MPC8315) u32 sata_clk; # endif -# if defined(CONFIG_MPC8360) +# if defined(CONFIG_ARCH_MPC8360) u32 mem_sec_clk; -# endif /* CONFIG_MPC8360 */ +# endif /* CONFIG_ARCH_MPC8360 */ #endif #endif #if defined(CONFIG_MPC85xx) || defined(CONFIG_MPC86xx) diff --git a/arch/powerpc/include/asm/immap_83xx.h b/arch/powerpc/include/asm/immap_83xx.h index afef36f262..d02da6495c 100644 --- a/arch/powerpc/include/asm/immap_83xx.h +++ b/arch/powerpc/include/asm/immap_83xx.h @@ -59,12 +59,12 @@ typedef struct sysconf83xx { u32 obir; /* Output Buffer Impedance Register */ u8 res8[0xC]; u32 pecr1; /* PCI Express control register 1 */ -#if defined(CONFIG_MPC830x) +#if defined(CONFIG_ARCH_MPC830X) u32 sdhccr; /* eSDHC Control Registers for MPC830x */ #else u32 pecr2; /* PCI Express control register 2 */ #endif -#if defined(CONFIG_MPC8309) +#if defined(CONFIG_ARCH_MPC8309) u32 can_dbg_ctrl; u32 res9a; u32 gpr1; @@ -604,7 +604,7 @@ typedef struct serdes83xx { * On Chip ROM */ typedef struct rom83xx { -#if defined(CONFIG_MPC8309) +#if defined(CONFIG_ARCH_MPC8309) u8 mem[0x8000]; #else u8 mem[0x10000]; @@ -625,7 +625,7 @@ typedef struct tdmdmac83xx { u8 fixme[0x2000]; } tdmdmac83xx_t; -#if defined(CONFIG_MPC834x) +#if defined(CONFIG_ARCH_MPC834X) typedef struct immap { sysconf83xx_t sysconf; /* System configuration */ wdt83xx_t wdt; /* Watch Dog Timer (WDT) Registers */ @@ -666,7 +666,7 @@ typedef struct immap { u8 res7[0xC0000]; } immap_t; -#ifndef CONFIG_MPC834x +#ifndef CONFIG_ARCH_MPC834X #ifdef CONFIG_HAS_FSL_MPH_USB #define CONFIG_SYS_MPC83xx_USB1_OFFSET 0x22000 /* use the MPH controller */ #define CONFIG_SYS_MPC83xx_USB2_OFFSET 0 @@ -679,7 +679,7 @@ typedef struct immap { #define CONFIG_SYS_MPC83xx_USB2_OFFSET 0x23000 #endif -#elif defined(CONFIG_MPC8313) +#elif defined(CONFIG_ARCH_MPC8313) typedef struct immap { sysconf83xx_t sysconf; /* System configuration */ wdt83xx_t wdt; /* Watch Dog Timer (WDT) Registers */ @@ -714,7 +714,7 @@ typedef struct immap { u8 res7[0xC0000]; } immap_t; -#elif defined(CONFIG_MPC8308) || defined(CONFIG_MPC8315) +#elif defined(CONFIG_ARCH_MPC8315) typedef struct immap { sysconf83xx_t sysconf; /* System configuration */ wdt83xx_t wdt; /* Watch Dog Timer (WDT) Registers */ @@ -729,8 +729,8 @@ typedef struct immap { gpio83xx_t gpio[1]; /* General purpose I/O module */ u8 res0[0x1300]; ddr83xx_t ddr; /* DDR Memory Controller Memory */ - fsl_i2c_t i2c[2]; /* I2C Controllers */ - u8 res1[0x1300]; + fsl_i2c_t i2c[1]; /* I2C Controllers */ + u8 res1[0x1400]; duart83xx_t duart[2]; /* DUART */ u8 res2[0x900]; fsl_lbc_t im_lbc; /* Local Bus Controller Regs */ @@ -759,7 +759,43 @@ typedef struct immap { u8 res12[0x1CF00]; } immap_t; -#elif defined(CONFIG_MPC837x) +#elif defined(CONFIG_ARCH_MPC8308) +typedef struct immap { + sysconf83xx_t sysconf; /* System configuration */ + wdt83xx_t wdt; /* Watch Dog Timer (WDT) Registers */ + rtclk83xx_t rtc; /* Real Time Clock Module Registers */ + rtclk83xx_t pit; /* Periodic Interval Timer */ + gtm83xx_t gtm[1]; /* Global Timers Module */ + u8 res0[0x100]; + ipic83xx_t ipic; /* Integrated Programmable Interrupt Controller */ + arbiter83xx_t arbiter; /* System Arbiter Registers */ + reset83xx_t reset; /* Reset Module */ + clk83xx_t clk; /* System Clock Module */ + pmc83xx_t pmc; /* Power Management Control Module */ + gpio83xx_t gpio[1]; /* General purpose I/O module */ + u8 res1[0x1300]; + ddr83xx_t ddr; /* DDR Memory Controller Memory */ + fsl_i2c_t i2c[2]; /* I2C Controllers */ + u8 res2[0x1300]; + duart83xx_t duart[2]; /* DUART */ + u8 res3[0x900]; + fsl_lbc_t im_lbc; /* Local Bus Controller Regs */ + u8 res4[0x1000]; + spi8xxx_t spi; /* Serial Peripheral Interface */ + u8 res5[0x1000]; + pex83xx_t pciexp[1]; /* PCI Express Controller */ + u8 res6[0x19000]; + usb83xx_t usb[1]; /* USB DR Controller */ + tsec83xx_t tsec[2]; + u8 res7[0x6000]; + tdmdmac83xx_t tdmdmac; /* TDM DMAC */ + sdhc83xx_t sdhc; /* SDHC Controller */ + u8 res8[0xb4000]; + serdes83xx_t serdes[1]; /* SerDes Registers */ + u8 res9[0x1CF00]; +} immap_t; + +#elif defined(CONFIG_ARCH_MPC837X) typedef struct immap { sysconf83xx_t sysconf; /* System configuration */ wdt83xx_t wdt; /* Watch Dog Timer (WDT) Registers */ @@ -803,7 +839,7 @@ typedef struct immap { rom83xx_t rom; /* On Chip ROM */ } immap_t; -#elif defined(CONFIG_MPC8360) +#elif defined(CONFIG_ARCH_MPC8360) typedef struct immap { sysconf83xx_t sysconf; /* System configuration */ wdt83xx_t wdt; /* Watch Dog Timer (WDT) Registers */ @@ -843,7 +879,7 @@ typedef struct immap { u8 qe[0x100000]; /* QE block */ } immap_t; -#elif defined(CONFIG_MPC832x) +#elif defined(CONFIG_ARCH_MPC832X) typedef struct immap { sysconf83xx_t sysconf; /* System configuration */ wdt83xx_t wdt; /* Watch Dog Timer (WDT) Registers */ @@ -879,7 +915,7 @@ typedef struct immap { u8 res8[0xC0000]; u8 qe[0x100000]; /* QE block */ } immap_t; -#elif defined(CONFIG_MPC8309) +#elif defined(CONFIG_ARCH_MPC8309) typedef struct immap { sysconf83xx_t sysconf; /* System configuration */ wdt83xx_t wdt; /* Watch Dog Timer (WDT) Registers */ @@ -946,7 +982,7 @@ typedef struct immap { #endif #define CONFIG_SYS_MPC83xx_USB1_ADDR \ (CONFIG_SYS_IMMR + CONFIG_SYS_MPC83xx_USB1_OFFSET) -#if defined(CONFIG_MPC834x) +#if defined(CONFIG_ARCH_MPC834X) #define CONFIG_SYS_MPC83xx_USB2_ADDR \ (CONFIG_SYS_IMMR + CONFIG_SYS_MPC83xx_USB2_OFFSET) #endif diff --git a/arch/powerpc/include/asm/mpc8xxx_spi.h b/arch/powerpc/include/asm/mpc8xxx_spi.h index 432be05469..b583a3269d 100644 --- a/arch/powerpc/include/asm/mpc8xxx_spi.h +++ b/arch/powerpc/include/asm/mpc8xxx_spi.h @@ -10,11 +10,11 @@ #include <asm/types.h> -#if defined(CONFIG_MPC8308) || \ - defined(CONFIG_MPC8313) || \ - defined(CONFIG_MPC8315) || \ - defined(CONFIG_MPC834x) || \ - defined(CONFIG_MPC837x) +#if defined(CONFIG_ARCH_MPC8308) || \ + defined(CONFIG_ARCH_MPC8313) || \ + defined(CONFIG_ARCH_MPC8315) || \ + defined(CONFIG_ARCH_MPC834X) || \ + defined(CONFIG_ARCH_MPC837X) typedef struct spi8xxx { u8 res0[0x20]; /* 0x0-0x01f reserved */ diff --git a/arch/powerpc/include/asm/processor.h b/arch/powerpc/include/asm/processor.h index f97ce48cc2..e03ab21f59 100644 --- a/arch/powerpc/include/asm/processor.h +++ b/arch/powerpc/include/asm/processor.h @@ -1203,127 +1203,7 @@ int fsl_qoriq_dsp_core_to_cluster(unsigned int core); #endif #endif - -/* what kind of prep workstation we are */ -extern int _prep_type; -/* - * This is used to identify the board type from a given PReP board - * vendor. Board revision is also made available. - */ -extern unsigned char ucSystemType; -extern unsigned char ucBoardRev; -extern unsigned char ucBoardRevMaj, ucBoardRevMin; - struct task_struct; -void start_thread(struct pt_regs *regs, unsigned long nip, unsigned long sp); -void release_thread(struct task_struct *); - -/* - * Create a new kernel thread. - */ -extern long kernel_thread(int (*fn)(void *), void *arg, unsigned long flags); - -/* - * Bus types - */ -#define EISA_bus 0 -#define EISA_bus__is_a_macro /* for versions in ksyms.c */ -#define MCA_bus 0 -#define MCA_bus__is_a_macro /* for versions in ksyms.c */ - -/* Lazy FPU handling on uni-processor */ -extern struct task_struct *last_task_used_math; -extern struct task_struct *last_task_used_altivec; - -/* - * this is the minimum allowable io space due to the location - * of the io areas on prep (first one at 0x80000000) but - * as soon as I get around to remapping the io areas with the BATs - * to match the mac we can raise this. -- Cort - */ -#define TASK_SIZE (0x80000000UL) - -/* This decides where the kernel will search for a free chunk of vm - * space during mmap's. - */ -#define TASK_UNMAPPED_BASE (TASK_SIZE / 8 * 3) - -typedef struct { - unsigned long seg; -} mm_segment_t; - -struct thread_struct { - unsigned long ksp; /* Kernel stack pointer */ - unsigned long wchan; /* Event task is sleeping on */ - struct pt_regs *regs; /* Pointer to saved register state */ - mm_segment_t fs; /* for get_fs() validation */ - void *pgdir; /* root of page-table tree */ - signed long last_syscall; - double fpr[32]; /* Complete floating point set */ - unsigned long fpscr_pad; /* fpr ... fpscr must be contiguous */ - unsigned long fpscr; /* Floating point status */ -#ifdef CONFIG_ALTIVEC - vector128 vr[32]; /* Complete AltiVec set */ - vector128 vscr; /* AltiVec status */ - unsigned long vrsave; -#endif /* CONFIG_ALTIVEC */ -}; - -#define INIT_SP (sizeof(init_stack) + (unsigned long) &init_stack) - -#define INIT_THREAD { \ - INIT_SP, /* ksp */ \ - 0, /* wchan */ \ - (struct pt_regs *)INIT_SP - 1, /* regs */ \ - KERNEL_DS, /*fs*/ \ - swapper_pg_dir, /* pgdir */ \ - 0, /* last_syscall */ \ - {0}, 0, 0 \ -} - -/* - * Note: the vm_start and vm_end fields here should *not* - * be in kernel space. (Could vm_end == vm_start perhaps?) - */ -#define INIT_MMAP { &init_mm, 0, 0x1000, NULL, \ - PAGE_SHARED, VM_READ | VM_WRITE | VM_EXEC, \ - 1, NULL, NULL } - -/* - * Return saved PC of a blocked thread. For now, this is the "user" PC - */ -static inline unsigned long thread_saved_pc(struct thread_struct *t) -{ - return (t->regs) ? t->regs->nip : 0; -} - -#define copy_segments(tsk, mm) do { } while (0) -#define release_segments(mm) do { } while (0) -#define forget_segments() do { } while (0) - -unsigned long get_wchan(struct task_struct *p); - -#define KSTK_EIP(tsk) ((tsk)->thread.regs->nip) -#define KSTK_ESP(tsk) ((tsk)->thread.regs->gpr[1]) - -/* - * NOTE! The task struct and the stack go together - */ -#define THREAD_SIZE (2*PAGE_SIZE) -#define alloc_task_struct() \ - ((struct task_struct *) __get_free_pages(GFP_KERNEL,1)) -#define free_task_struct(p) free_pages((unsigned long)(p),1) -#define get_task_struct(tsk) atomic_inc(&mem_map[MAP_NR(tsk)].count) - -/* in process.c - for early bootup debug -- Cort */ -int ll_printk(const char *, ...); -void ll_puts(const char *); - -#define init_task (init_task_union.task) -#define init_stack (init_task_union.stack) - -/* In misc.c */ -void _nmask_and_or_msr(unsigned long nmask, unsigned long or_val); #ifndef CONFIG_CPU_MPC83XX int prt_83xx_rsr(void); |