summaryrefslogtreecommitdiff
path: root/board/actux1
diff options
context:
space:
mode:
Diffstat (limited to 'board/actux1')
-rw-r--r--board/actux1/Makefile8
-rw-r--r--board/actux1/actux1.c148
-rw-r--r--board/actux1/actux1_hw.h41
-rw-r--r--board/actux1/u-boot.lds99
4 files changed, 0 insertions, 296 deletions
diff --git a/board/actux1/Makefile b/board/actux1/Makefile
deleted file mode 100644
index 05a8669113..0000000000
--- a/board/actux1/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := actux1.o
diff --git a/board/actux1/actux1.c b/board/actux1/actux1.c
deleted file mode 100644
index 03ccd936b4..0000000000
--- a/board/actux1/actux1.c
+++ /dev/null
@@ -1,148 +0,0 @@
-/*
- * (C) Copyright 2007
- * Michael Schwingen, michael@schwingen.org
- *
- * (C) Copyright 2006
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * (C) Copyright 2002
- * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
- *
- * (C) Copyright 2002
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <command.h>
-#include <malloc.h>
-#include <asm/arch/ixp425.h>
-#include <asm/io.h>
-#include <miiphy.h>
-#ifdef CONFIG_PCI
-#include <pci.h>
-#include <asm/arch/ixp425pci.h>
-#endif
-
-#include "actux1_hw.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_early_init_f(void)
-{
- /* CS5: Debug port */
- writel(0x9d520003, IXP425_EXP_CS5);
- /* CS6: HwRel */
- writel(0x81860001, IXP425_EXP_CS6);
- /* CS7: LEDs */
- writel(0x80900003, IXP425_EXP_CS7);
- return 0;
-}
-
-int board_init(void)
-{
- /* adress of boot parameters */
- gd->bd->bi_boot_params = 0x00000100;
-
- GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_IORST);
- GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_IORST);
-
- /* Setup GPIOs for PCI INTA */
- GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_PCI1_INTA);
- GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_PCI1_INTA);
-
- /* Setup GPIOs for 33MHz clock output */
- GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCI_CLK);
- GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_EXTBUS_CLK);
- writel(0x011001FF, IXP425_GPIO_GPCLKR);
-
- udelay(533);
- GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_IORST);
-
- ACTUX1_LED1(2);
- ACTUX1_LED2(2);
- ACTUX1_LED3(0);
- ACTUX1_LED4(0);
- ACTUX1_LED5(0);
- ACTUX1_LED6(0);
- ACTUX1_LED7(0);
-
- ACTUX1_HS(ACTUX1_HS_DCD);
-
- return 0;
-}
-
-/*
- * Check Board Identity
- */
-int checkboard(void)
-{
- char buf[64];
- int i = getenv_f("serial#", buf, sizeof(buf));
-
- puts("Board: AcTux-1 rev.");
- putc(ACTUX1_BOARDREL + 'A' - 1);
-
- if (i > 0) {
- puts(", serial# ");
- puts(buf);
- }
- putc('\n');
-
- return 0;
-}
-
-/*************************************************************************
- * get_board_rev() - setup to pass kernel board revision information
- * 0 = reserved
- * 1 = Rev. A
- * 2 = Rev. B
- *************************************************************************/
-u32 get_board_rev(void)
-{
- return ACTUX1_BOARDREL;
-}
-
-int dram_init(void)
-{
- gd->ram_size = get_ram_size(CONFIG_SYS_SDRAM_BASE, 128<<20);
- return 0;
-}
-
-
-#ifdef CONFIG_PCI
-struct pci_controller hose;
-
-void pci_init_board(void)
-{
- pci_ixp_init(&hose);
-}
-#endif
-
-void reset_phy(void)
-{
- u16 id1, id2;
-
- /* initialize the PHY */
- miiphy_reset("NPE0", CONFIG_PHY_ADDR);
-
- miiphy_read("NPE0", CONFIG_PHY_ADDR, MII_PHYSID1, &id1);
- miiphy_read("NPE0", CONFIG_PHY_ADDR, MII_PHYSID2, &id2);
-
- id2 &= 0xFFF0; /* mask out revision bits */
-
- if (id1 == 0x13 && id2 == 0x78e0) {
- /*
- * LXT971/LXT972 PHY: set LED outputs:
- * LED1(green) = Link/ACT,
- * LED2 (unused) = LINK,
- * LED3(red) = Coll
- */
- miiphy_write("NPE0", CONFIG_PHY_ADDR, 20, 0xD432);
- } else if (id1 == 0x143 && id2 == 0xbc30) {
- /* BCM5241: default values are OK */
- } else
- printf("unknown ethernet PHY ID: %x %x\n", id1, id2);
-}
diff --git a/board/actux1/actux1_hw.h b/board/actux1/actux1_hw.h
deleted file mode 100644
index 5627f24796..0000000000
--- a/board/actux1/actux1_hw.h
+++ /dev/null
@@ -1,41 +0,0 @@
-/*
- * (C) Copyright 2007
- * Michael Schwingen, michael@schwingen.org
- *
- * hardware register definitions for the AcTux-1 board.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef _ACTUX1_HW_H
-#define _ACTUX1_HW_H
-
-/* 0 = LED off,1 = green, 2 = red, 3 = orange */
-#define ACTUX1_LED1(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 0)
-#define ACTUX1_LED2(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 1)
-#define ACTUX1_LED3(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 2)
-#define ACTUX1_LED4(a) writeb((a)^3, IXP425_EXP_BUS_CS7_BASE_PHYS + 3)
-#define ACTUX1_LED5(a) writeb((a)^3, IXP425_EXP_BUS_CS7_BASE_PHYS + 4)
-#define ACTUX1_LED6(a) writeb((a)^3, IXP425_EXP_BUS_CS7_BASE_PHYS + 5)
-#define ACTUX1_LED7(a) writeb((a)^3, IXP425_EXP_BUS_CS7_BASE_PHYS + 6)
-#define ACTUX1_HS(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 7)
-#define ACTUX1_HS_DCD 0x01
-#define ACTUX1_HS_DSR 0x02
-
-#define ACTUX1_DBG_PORT IXP425_EXP_BUS_CS5_BASE_PHYS
-#define ACTUX1_BOARDREL (readb(IXP425_EXP_BUS_CS6_BASE_PHYS) & 0x0F)
-
-/* GPIO settings */
-#define CONFIG_SYS_GPIO_PCI1_INTA 2
-#define CONFIG_SYS_GPIO_PCI2_INTA 3
-#define CONFIG_SYS_GPIO_I2C_SDA 4
-#define CONFIG_SYS_GPIO_I2C_SCL 5
-#define CONFIG_SYS_GPIO_DBGJUMPER 9
-#define CONFIG_SYS_GPIO_BUTTON1 10
-#define CONFIG_SYS_GPIO_DBGSENSE 11
-#define CONFIG_SYS_GPIO_DTR 12
-#define CONFIG_SYS_GPIO_IORST 13 /* Out */
-#define CONFIG_SYS_GPIO_PCI_CLK 14 /* Out */
-#define CONFIG_SYS_GPIO_EXTBUS_CLK 15 /* Out */
-
-#endif
diff --git a/board/actux1/u-boot.lds b/board/actux1/u-boot.lds
deleted file mode 100644
index 4716e4f0e0..0000000000
--- a/board/actux1/u-boot.lds
+++ /dev/null
@@ -1,99 +0,0 @@
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-OUTPUT_FORMAT ("elf32-bigarm", "elf32-bigarm", "elf32-bigarm")
-OUTPUT_ARCH (arm)
-ENTRY (_start)
-SECTIONS
-{
- . = 0x00000000;
-
- . = ALIGN (4);
- .text : {
- *(.__image_copy_start)
- arch/arm/cpu/ixp/start.o(.text*)
- net/built-in.o(.text*)
- board/actux1/built-in.o(.text*)
- arch/arm/cpu/ixp/built-in.o(.text*)
- drivers/input/built-in.o(.text*)
-
- . = env_offset;
- common/env_embedded.o(.ppcenv)
- *(.text*)
- }
-
- . = ALIGN(4);
- .rodata : {
- *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
- }
- . = ALIGN(4);
- .data : {
- *(.data*)
- }
- . = ALIGN(4);
- .got : {
- *(.got)
- }
- . =.;
-
- . = ALIGN(4);
- .u_boot_list : {
- KEEP(*(SORT(.u_boot_list*)));
- }
-
- . = ALIGN (4);
-
- .image_copy_end :
- {
- *(.__image_copy_end)
- }
-
- .rel_dyn_start :
- {
- *(.__rel_dyn_start)
- }
-
- .rel.dyn : {
- *(.rel*)
- }
-
- .rel_dyn_end :
- {
- *(.__rel_dyn_end)
- }
-
- _end = .;
-
-/*
- * Compiler-generated __bss_start and __bss_end, see arch/arm/lib/bss.c
- * __bss_base and __bss_limit are for linker only (overlay ordering)
- */
-
- .bss_start __rel_dyn_start (OVERLAY) : {
- KEEP(*(.__bss_start));
- __bss_base = .;
- }
-
- .bss __bss_base (OVERLAY) : {
- *(.bss*)
- . = ALIGN(4);
- __bss_limit = .;
- }
- .bss_end __bss_limit (OVERLAY) : {
- KEEP(*(.__bss_end));
- }
-
- .dynsym _end : { *(.dynsym) }
- .dynbss : { *(.dynbss) }
- .dynstr : { *(.dynstr*) }
- .dynamic : { *(.dynamic*) }
- .hash : { *(.hash*) }
- .plt : { *(.plt*) }
- .interp : { *(.interp*) }
- .gnu : { *(.gnu*) }
- .ARM.exidx : { *(.ARM.exidx*) }
-}
generated by cgit (git 2.34.1) at 2024-12-27 11:27:51 +0000