diff options
Diffstat (limited to 'board/bf518f-ezbrd')
| -rw-r--r-- | board/bf518f-ezbrd/bf518f-ezbrd.c | 41 |
1 files changed, 19 insertions, 22 deletions
diff --git a/board/bf518f-ezbrd/bf518f-ezbrd.c b/board/bf518f-ezbrd/bf518f-ezbrd.c index 85b350f3ec..ff1ac4cda8 100644 --- a/board/bf518f-ezbrd/bf518f-ezbrd.c +++ b/board/bf518f-ezbrd/bf518f-ezbrd.c @@ -14,6 +14,7 @@ #include <spi.h> #include <asm/blackfin.h> #include <asm/net.h> +#include <asm/portmux.h> #include <asm/mach-common/bits/otp.h> #include <asm/sdh.h> @@ -61,6 +62,7 @@ static void board_init_enetaddr(uchar *mac_addr) #define KSZ_WRITE 0x02 #define KSZ_READ 0x03 +#define KSZ_REG_CHID 0x00 /* Register 0: Chip ID0 */ #define KSZ_REG_STPID 0x01 /* Register 1: Chip ID1 / Start Switch */ #define KSZ_REG_GC9 0x0b /* Register 11: Global Control 9 */ #define KSZ_REG_P3C0 0x30 /* Register 48: Port 3 Control 0 */ @@ -78,15 +80,17 @@ static int ksz8893m_reg_set(struct spi_slave *slave, uchar reg, uchar data) return ksz8893m_transfer(slave, KSZ_WRITE, reg, data, din); } -static int ksz8893m_reg_clear(struct spi_slave *slave, uchar reg, uchar mask) +static int ksz8893m_reg_read(struct spi_slave *slave, uchar reg) { - int ret = 0; + int ret; unsigned char din[3]; + ret = ksz8893m_transfer(slave, KSZ_READ, reg, 0, din); + return ret ? ret : din[2]; +} - ret |= ksz8893m_transfer(slave, KSZ_READ, reg, 0, din); - ret |= ksz8893m_reg_set(slave, reg, din[2] & mask); - - return ret; +static int ksz8893m_reg_clear(struct spi_slave *slave, uchar reg, uchar mask) +{ + return ksz8893m_reg_set(slave, reg, ksz8893m_reg_read(slave, reg) & mask); } static int ksz8893m_reset(struct spi_slave *slave) @@ -107,16 +111,16 @@ static int ksz8893m_reset(struct spi_slave *slave) int board_eth_init(bd_t *bis) { - static bool switch_is_alive = false; + static bool switch_is_alive = false, phy_is_ksz = true; int ret; if (!switch_is_alive) { struct spi_slave *slave = spi_setup_slave(0, 1, KSZ_MAX_HZ, SPI_MODE_3); if (slave) { if (!spi_claim_bus(slave)) { - ret = ksz8893m_reset(slave); - if (!ret) - switch_is_alive = true; + phy_is_ksz = (ksz8893m_reg_read(slave, KSZ_REG_CHID) == 0x88); + ret = phy_is_ksz ? ksz8893m_reset(slave) : 0; + switch_is_alive = (ret == 0); spi_release_bus(slave); } spi_free_slave(slave); @@ -143,18 +147,11 @@ int misc_init_r(void) int board_early_init_f(void) { -#if !defined(CONFIG_SYS_NO_FLASH) - /* setup BF518-EZBRD GPIO pin PG11 to AMS2. */ - bfin_write_PORTG_MUX((bfin_read_PORTG_MUX() & ~PORT_x_MUX_6_MASK) | PORT_x_MUX_6_FUNC_2); - bfin_write_PORTG_FER(bfin_read_PORTG_FER() | PG11); - -# if !defined(CONFIG_BFIN_SPI) - /* setup BF518-EZBRD GPIO pin PG15 to AMS3. */ - bfin_write_PORTG_MUX((bfin_read_PORTG_MUX() & ~PORT_x_MUX_7_MASK) | PORT_x_MUX_7_FUNC_3); - bfin_write_PORTG_FER(bfin_read_PORTG_FER() | PG15); -# endif -#endif - return 0; + /* connect async banks by default */ + const unsigned short pins[] = { + P_AMS2, P_AMS3, 0, + }; + return peripheral_request_list(pins, "async"); } #ifdef CONFIG_BFIN_SDH |