diff options
Diffstat (limited to 'board/freescale/bsc9131rdb/README')
| -rw-r--r-- | board/freescale/bsc9131rdb/README | 151 |
1 files changed, 0 insertions, 151 deletions
diff --git a/board/freescale/bsc9131rdb/README b/board/freescale/bsc9131rdb/README deleted file mode 100644 index c8405970c1..0000000000 --- a/board/freescale/bsc9131rdb/README +++ /dev/null @@ -1,151 +0,0 @@ -Overview --------- -- BSC9131 is integrated device that targets Femto base station market. - It combines Power Architecture e500v2 and DSP StarCore SC3850 core - technologies with MAPLE-B2F baseband acceleration processing elements. -- It's MAPLE disabled personality is called 9231. - -The BSC9131 SoC includes the following function and features: -. Power Architecture subsystem including a e500 processor with 256-Kbyte shared - L2 cache -. StarCore SC3850 DSP subsystem with a 512-Kbyte private L2 cache -. The Multi Accelerator Platform Engine for Femto BaseStation Baseband - Processing (MAPLE-B2F) -. A multi-standard baseband algorithm accelerator for Channel Decoding/Encoding, - Fourier Transforms, UMTS chip rate processing, LTE UP/DL Channel processing, - and CRC algorithms -. Consists of accelerators for Convolution, Filtering, Turbo Encoding, - Turbo Decoding, Viterbi decoding, Chiprate processing, and Matrix Inversion - operations -. DDR3/3L memory interface with 32-bit data width without ECC and 16-bit with - ECC, up to 400-MHz clock/800 MHz data rate -. Dedicated security engine featuring trusted boot -. DMA controller -. OCNDMA with four bidirectional channels -. Interfaces -. Two triple-speed Gigabit Ethernet controllers featuring network acceleration - including IEEE 1588. v2 hardware support and virtualization (eTSEC) -. eTSEC 1 supports RGMII/RMII -. eTSEC 2 supports RGMII -. High-speed USB 2.0 host and device controller with ULPI interface -. Enhanced secure digital (SD/MMC) host controller (eSDHC) -. Antenna interface controller (AIC), supporting three industry standard - JESD207/three custom ADI RF interfaces (two dual port and one single port) - and three MAXIM's MaxPHY serial interfaces -. ADI lanes support both full duplex FDD support and half duplex TDD support -. Universal Subscriber Identity Module (USIM) interface that facilitates - communication to SIM cards or Eurochip pre-paid phone cards -. TDM with one TDM port -. Two DUART, four eSPI, and two I2C controllers -. Integrated Flash memory controller (IFC) -. TDM with 256 channels -. GPIO -. Sixteen 32-bit timers - -The e500 core subsystem within the Power Architecture consists of the following: -. 32-Kbyte L1 instruction cache -. 32-Kbyte L1 data cache -. 256-Kbyte L2 cache/L2 memory/L2 stash -. programmable interrupt controller (PIC) -. Debug support -. Timers - -The SC3850 core subsystem consists of the following: -. 32 Kbyte 8-way level 1 instruction cache (L1 ICache) -. 32 Kbyte 8-way level 1 data cache (L1 DCache) -. 512 Kbyte 8-way level 2 unified instruction/data cache (M2 memory) -. Memory management unit (MMU) -. Enhanced programmable interrupt controller (EPIC) -. Debug and profiling unit (DPU) -. Two 32-bit timers - -BSC9131RDB board Overview -------------------------- - 1Gbyte DDR3 (on board DDR) - 128Mbyte 2K page size NAND Flash - 256 Kbit M24256 I2C EEPROM - 128 Mbit SPI Flash memory - USB-ULPI - eTSEC1: Connected to RGMII PHY - eTSEC2: Connected to RGMII PHY - DUART interface: supports one UARTs up to 115200 bps for console display - USIM connector - -Frequency Combinations Supported --------------------------------- -Core MHz/CCB MHz/DDR(MT/s) -1. 1000/500/800 -2. 800/400/667 - -Boot Methods Supported ------------------------ -1. NAND Flash -2. SPI Flash - -Default Boot Method --------------------- -NAND boot - -Building U-Boot --------------- -To build the U-Boot for BSC9131RDB: -1. NAND Flash with sysclk 66MHz(J16 on RDB closed, default) - make BSC9131RDB_NAND -2. NAND Flash with sysclk 100MHz(J16 on RDB open) - make BSC9131RDB_NAND_SYSCLK100 -3. SPI Flash with sysclk 66MHz(J16 on RDB closed, default) - make BSC9131RDB_SPIFLASH -4. SPI Flash with sysclk 100MHz(J16 on RDB open) - make BSC9131RDB_SPIFLASH_SYSCLK100 - -Memory map ------------ - 0x0000_0000 0x7FFF_FFFF DDR 1G cacheable - 0xA0000000 0xBFFFFFFF Shared DSP core L2/M2 space 512M - 0xC100_0000 0xC13F_FFFF MAPLE-2F 4M - 0xC1F0_0000 0xC1F3_FFFF PA SRAM Region 0 256K - 0xC1F8_0000 0xC1F9_FFFF PA SRAM Region 1 128K - 0xFED0_0000 0xFED0_3FFF SEC Secured RAM 16K - 0xFEE0_0000 0xFEE0_0FFF DSP Boot ROM 4K - 0xFF60_0000 0xFF6F_FFFF DSP CCSR 1M - 0xFF70_0000 0xFF7F_FFFF PA CCSR 1M - 0xFF80_0000 0xFFFF_FFFF Boot Page & NAND Buffer 8M - -DDR Memory map ---------------- - 0x0000_0000 0x36FF_FFFF Memory passed onto Linux - 0x3700_0000 0x37FF_FFFF PowerPC-DSP shared control area - 0x3800_0000 0x4FFF_FFFF DSP Private area - - Out of 880M, passed onto Linux, 1hugetlb page of 256M is reserved for - data communcation between PowerPC and DSP core. - Rest is PowerPC private area. - -Flashing Images ---------------- -To place a new U-Boot image in the NAND flash and then boot -with that new image temporarily, use this: - tftp 1000000 u-boot-nand.bin - nand erase 0 100000 - nand write 1000000 0 100000 - reset - -Using the Device Tree Source File ---------------------------------- -To create the DTB (Device Tree Binary) image file, -use a command similar to this: - - dtc -b 0 -f -I dts -O dtb bsc9131rdb.dts > bsc9131rdb.dtb - -Likely, that .dts file will come from here; - - linux-2.6/arch/powerpc/boot/dts/bsc9131rdb.dts - -Booting Linux -------------- -Place a linux uImage in the TFTP disk area. - - tftp 1000000 uImage - tftp 2000000 rootfs.ext2.gz.uboot - tftp c00000 bsc9131rdb.dtb - bootm 1000000 2000000 c00000 |