diff options
Diffstat (limited to 'board/freescale/mx6sabresd')
-rw-r--r-- | board/freescale/mx6sabresd/MAINTAINERS | 1 | ||||
-rw-r--r-- | board/freescale/mx6sabresd/mx6sabresd.c | 90 | ||||
-rw-r--r-- | board/freescale/mx6sabresd/mx6sabresd_spl.cfg | 58 |
3 files changed, 41 insertions, 108 deletions
diff --git a/board/freescale/mx6sabresd/MAINTAINERS b/board/freescale/mx6sabresd/MAINTAINERS index 69c0a3065f..0011ec7b49 100644 --- a/board/freescale/mx6sabresd/MAINTAINERS +++ b/board/freescale/mx6sabresd/MAINTAINERS @@ -5,3 +5,4 @@ F: board/freescale/mx6sabresd/ F: include/configs/mx6sabresd.h F: configs/mx6dlsabresd_defconfig F: configs/mx6qsabresd_defconfig +F: configs/mx6sabresd_spl_defconfig diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c index 1142e8a27e..ac3757f074 100644 --- a/board/freescale/mx6sabresd/mx6sabresd.c +++ b/board/freescale/mx6sabresd/mx6sabresd.c @@ -27,12 +27,11 @@ #include <i2c.h> #include <power/pmic.h> #include <power/pfuze100_pmic.h> +#include "../common/pfuze.h" #include <asm/arch/mx6-ddr.h> DECLARE_GLOBAL_DATA_PTR; -#define BOOT_CFG 0x020D8004 - #define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \ PAD_CTL_SRE_FAST | PAD_CTL_HYS) @@ -300,7 +299,8 @@ int board_mmc_init(bd_t *bis) return 0; #else - unsigned reg = readl(BOOT_CFG) >> 11; + struct src *psrc = (struct src *)SRC_BASE_ADDR; + unsigned reg = readl(&psrc->sbmr1) >> 11; /* * Upon reading BOOT_CFG register the following map is done: * Bit 11 and 12 of BOOT_CFG register can determine the current @@ -560,60 +560,27 @@ int board_init(void) return 0; } -static int pfuze_init(void) +int power_init_board(void) { struct pmic *p; - int ret; unsigned int reg; - ret = power_pfuze100_init(I2C_PMIC); - if (ret) - return ret; - - p = pmic_get("PFUZE100"); - ret = pmic_probe(p); - if (ret) - return ret; - - pmic_reg_read(p, PFUZE100_DEVICEID, ®); - printf("PMIC: PFUZE100 ID=0x%02x\n", reg); + p = pfuze_common_init(I2C_PMIC); + if (!p) + return -ENODEV; /* Increase VGEN3 from 2.5 to 2.8V */ pmic_reg_read(p, PFUZE100_VGEN3VOL, ®); - reg &= ~0xf; - reg |= 0xa; + reg &= ~LDO_VOL_MASK; + reg |= LDOB_2_80V; pmic_reg_write(p, PFUZE100_VGEN3VOL, reg); /* Increase VGEN5 from 2.8 to 3V */ pmic_reg_read(p, PFUZE100_VGEN5VOL, ®); - reg &= ~0xf; - reg |= 0xc; + reg &= ~LDO_VOL_MASK; + reg |= LDOB_3_00V; pmic_reg_write(p, PFUZE100_VGEN5VOL, reg); - /* Set SW1AB stanby volage to 0.975V */ - pmic_reg_read(p, PFUZE100_SW1ABSTBY, ®); - reg &= ~0x3f; - reg |= 0x1b; - pmic_reg_write(p, PFUZE100_SW1ABSTBY, reg); - - /* Set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */ - pmic_reg_read(p, PUZE_100_SW1ABCONF, ®); - reg &= ~0xc0; - reg |= 0x40; - pmic_reg_write(p, PUZE_100_SW1ABCONF, reg); - - /* Set SW1C standby voltage to 0.975V */ - pmic_reg_read(p, PFUZE100_SW1CSTBY, ®); - reg &= ~0x3f; - reg |= 0x1b; - pmic_reg_write(p, PFUZE100_SW1CSTBY, reg); - - /* Set SW1C/VDDSOC step ramp up time from 16us to 4us/25mV */ - pmic_reg_read(p, PFUZE100_SW1CCONF, ®); - reg &= ~0xc0; - reg |= 0x40; - pmic_reg_write(p, PFUZE100_SW1CCONF, reg); - return 0; } @@ -640,8 +607,6 @@ int board_late_init(void) #ifdef CONFIG_CMD_BMODE add_board_boot_modes(board_boot_modes); #endif - pfuze_init(); - return 0; } @@ -729,11 +694,33 @@ static struct mx6_ddr3_cfg mem_ddr = { .trasmin = 3500, }; +static void ccgr_init(void) +{ + struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; + + writel(0x00C03F3F, &ccm->CCGR0); + writel(0x0030FC03, &ccm->CCGR1); + writel(0x0FFFC000, &ccm->CCGR2); + writel(0x3FF00000, &ccm->CCGR3); + writel(0x00FFF300, &ccm->CCGR4); + writel(0x0F0000C3, &ccm->CCGR5); + writel(0x000003FF, &ccm->CCGR6); +} + +static void gpr_init(void) +{ + struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; + + /* enable AXI cache for VDOA/VPU/IPU */ + writel(0xF00000CF, &iomux->gpr[4]); + /* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */ + writel(0x007F007F, &iomux->gpr[6]); + writel(0x007F007F, &iomux->gpr[7]); +} + /* - * This section require the differentiation - * between iMX6 Sabre Families. - * But for now, it will configure only for - * SabreSD. + * This section requires the differentiation between iMX6 Sabre boards, but + * for now, it will configure only for the mx6q variant. */ static void spl_dram_init(void) { @@ -768,6 +755,9 @@ void board_init_f(ulong dummy) /* setup AIPS and disable watchdog */ arch_cpu_init(); + ccgr_init(); + gpr_init(); + /* iomux and setup of i2c */ board_early_init_f(); diff --git a/board/freescale/mx6sabresd/mx6sabresd_spl.cfg b/board/freescale/mx6sabresd/mx6sabresd_spl.cfg deleted file mode 100644 index 2bf48175ef..0000000000 --- a/board/freescale/mx6sabresd/mx6sabresd_spl.cfg +++ /dev/null @@ -1,58 +0,0 @@ -/* - * Copyright (C) 2011 Freescale Semiconductor, Inc. - * Jason Liu <r64343@freescale.com> - * - * SPDX-License-Identifier: GPL-2.0+ - * - * Refer doc/README.imximage for more details about how-to configure - * and create imximage boot image - * - * The syntax is taken as close as possible with the kwbimage - */ - -/* image version */ -IMAGE_VERSION 2 - -/* - * Boot Device : one of - * spi, sd (the board has no nand neither onenand) - */ -BOOT_FROM sd - -/* - * Device Configuration Data (DCD) - * - * Each entry must have the format: - * Addr-type Address Value - * - * where: - * Addr-type register length (1,2 or 4 bytes) - * Address absolute address of the register - * value value to be stored in the register - */ - -/* set the default clock gate to save power */ -DATA 4 0x020c4068 0x00C03F3F -DATA 4 0x020c406c 0x0030FC03 -DATA 4 0x020c4070 0x0FFFC000 -DATA 4 0x020c4074 0x3FF00000 -DATA 4 0x020c4078 0x00FFF300 -DATA 4 0x020c407c 0x0F0000C3 -DATA 4 0x020c4080 0x000003FF - -/* enable AXI cache for VDOA/VPU/IPU */ -DATA 4 0x020e0010 0xF00000CF -/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */ -DATA 4 0x020e0018 0x007F007F -DATA 4 0x020e001c 0x007F007F - -/* - * Setup CCM_CCOSR register as follows: - * - * cko1_en = 1 --> CKO1 enabled - * cko1_div = 111 --> divide by 8 - * cko1_sel = 1011 --> ahb_clk_root - * - * This sets CKO1 at ahb_clk_root/8 = 132/8 = 16.5 MHz - */ -DATA 4 0x020c4060 0x000000fb |