diff options
Diffstat (limited to 'board/freescale/p1023rds')
| -rw-r--r-- | board/freescale/p1023rds/Makefile | 9 | ||||
| -rw-r--r-- | board/freescale/p1023rds/README | 101 | ||||
| -rw-r--r-- | board/freescale/p1023rds/bcsr.h | 49 | ||||
| -rw-r--r-- | board/freescale/p1023rds/law.c | 19 | ||||
| -rw-r--r-- | board/freescale/p1023rds/p1023rds.c | 191 | ||||
| -rw-r--r-- | board/freescale/p1023rds/tlb.c | 100 |
6 files changed, 0 insertions, 469 deletions
diff --git a/board/freescale/p1023rds/Makefile b/board/freescale/p1023rds/Makefile deleted file mode 100644 index fdbf365ea5..0000000000 --- a/board/freescale/p1023rds/Makefile +++ /dev/null @@ -1,9 +0,0 @@ -# -# Copyright 2010-2011 Freescale Semiconductor, Inc. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y += p1023rds.o -obj-y += law.o -obj-y += tlb.o diff --git a/board/freescale/p1023rds/README b/board/freescale/p1023rds/README deleted file mode 100644 index d382551c4d..0000000000 --- a/board/freescale/p1023rds/README +++ /dev/null @@ -1,101 +0,0 @@ -Overview --------- -The P1023 process includes a performance optimized implementation of the -QorIQ data Path Acceleration Architecture (DPAA). This architecture -provides the infrastructure to support simplified sharing of networking -interfaces and accelerators by multiple CPU cores. P1023 is an e500 based -dual core SOC. - -P1023RDS board is a Low End Dual core platform supporting the P1023 -processor of QorIQ series. - -Building U-boot ---------------- -To build the u-boot for P1023RDS: -Configure to NOR boot: - make P1023RDS_config -Configure to NAND boot: - make P1023RDS_NAND_config -Build: - make - -Board Switches --------------- -Most switches on the board should not be changed. The most frequent -user-settable switches on the board are used to configure -the flash banks. - -J4: all open - -Default NOR flash boot switch setting: - Sw3[1:8]: off on on off on on off off - Sw4[1:8]: off off off on off off off off - Sw6[1:8]: off on off on off on on off - Sw7[1:8]: off on off off on off off off - Sw8[1:8]: on off off off off off off off - -For NAND flash boot,set -Sw4[1:4]: off on on on - -The default native ethernet setting is for RGMII mode. -To use SGMII mode, set -SW8[1:2]: OFF OFF -SW7[6:7]: ON ON - -Memory Map ----------- -0x0000_0000 0x7fff_ffff DDR 2G Cacheable -0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable -0xc000_0000 0xdfff_ffff PCI 512M non-cacheable -0xe100_0000 0xe3ff_ffff PCI IO range 4M non-cacheable - -0xe000_0000 0xe003_ffff BCSR 256K BCSR -0xee00_0000 0xefff_ffff NOR flash 32M NOR flash -0xff00_0000 0xff3f_ffff DPAA_QBMAN 4M -0xff60_0000 0xff7f_ffff CCSR 2M non-cacheable -0xffa0_0000 0xffaf_ffff NAND FLASH 1M non-cacheable -0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0 - -Flashing u-boot Images ---------------- -To program the image in the boot flash bank: -NOR flash boot: - => tftp 1000000 u-boot.bin - => protect off all - => erase eff40000 efffffff - => cp.b 1000000 eff40000 c0000 - -NAND flash boot: - => tftp 1000000 u-boot-nand.bin - => nand erase 0 80000 - => nand write 1000000 0 80000 - -Firmware ucode location ---------------------------------- -Microcode(ucode) to FMAN's IRAM is needed to make FMAN Ethernet work. -u-boot loads ucode FLASH. The location for ucode: -NOR Flash: 0xfe000000 -NAND Flash: 0x1f00000 - -Using the Device Tree Source File ---------------------------------- -To create the DTB (Device Tree Binary) image file, -use a command similar to this: - - dtc -b 0 -f -I dts -O dtb p1023rds.dts > p1023rds.dtb - -Likely, that .dts file will come from here; - - linux-2.6/arch/powerpc/boot/dts/p1023rds.dts -or - make p1023rds.dtb ARCH=powerpc -in linux-2.6 directory. - -Booting Linux -------------- -Place a linux uImage in the TFTP disk area. - - tftp 1000000 uImage - tftp 2000000 rootfs.ext2.gz.uboot - tftp c00000 p1023rds.dtb - bootm 1000000 2000000 c00000 diff --git a/board/freescale/p1023rds/bcsr.h b/board/freescale/p1023rds/bcsr.h deleted file mode 100644 index a9deb72f78..0000000000 --- a/board/freescale/p1023rds/bcsr.h +++ /dev/null @@ -1,49 +0,0 @@ -/* - * Copyright (C) 2011 Freescale Semiconductor, Inc. - * - * Authors: Chunhe Lan <b25806@freescale.com> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __BCSR_H_ -#define __BCSR_H_ - -#include <common.h> - -/* - * BCSR Bit definitions - * BCSR 15 * - 0 device insertion oriention - 1 stack processor present - 2 power supply shut down/normal operation - 3 I2C bus0 drive enable - 4 reserved - 5:7 I2C bus0 select - 5 - I2C_BUS_0_SS0 - 6 - I2C_BUS_0_SS1 - 7 - I2C_BUS_0_SS2 -*/ - -/* BCSR register base address is 0xFX000020 */ -#define BCSR_BASE_REG_OFFSET 0x20 -#define BCSR_ACCESS_REG_ADDR (CONFIG_SYS_BCSR_BASE + BCSR_BASE_REG_OFFSET) - -#define BCSR15_DEV_INS_ORI 0x80 -#define BCSR15_STACK_PRO_PRE 0x40 -#define BCSR15_POWER_SUPPLY 0x20 -#define BCSR15_I2C_BUS0_EN 0x10 -#define BCSR15_I2C_BUS0_SEG0 0x00 -#define BCSR15_I2C_BUS0_SEG1 0x04 -#define BCSR15_I2C_BUS0_SEG2 0x02 -#define BCSR15_I2C_BUS0_SEG3 0x06 -#define BCSR15_I2C_BUS0_SEG4 0x01 -#define BCSR15_I2C_BUS0_SEG5 0x05 -#define BCSR15_I2C_BUS0_SEG6 0x03 -#define BCSR15_I2C_BUS0_SEG7 0x07 -#define BCSR15_I2C_BUS0_SEG_CLR 0x07 -#define BCSR19_SGMII_SEL_L 0x01 - -/*BCSR Utils functions*/ -void fixup_i2c_bus0_sel_seg0(void); -#endif /* __BCSR_H_ */ diff --git a/board/freescale/p1023rds/law.c b/board/freescale/p1023rds/law.c deleted file mode 100644 index 92f5a3fcb5..0000000000 --- a/board/freescale/p1023rds/law.c +++ /dev/null @@ -1,19 +0,0 @@ -/* - * Copyright 2010-2011 Freescale Semiconductor, Inc. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <asm/fsl_law.h> -#include <asm/mmu.h> - -struct law_entry law_table[] = { - SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_LBC), - SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_4M, - LAW_TRGT_IF_DPAA_SWP_SRAM), - /* The LAW 0xe0000000 ~ 0xefffffff for BCSR and NOR flash */ - SET_LAW(CONFIG_SYS_BCSR_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_LBC), -}; - -int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/freescale/p1023rds/p1023rds.c b/board/freescale/p1023rds/p1023rds.c deleted file mode 100644 index 2b883c719e..0000000000 --- a/board/freescale/p1023rds/p1023rds.c +++ /dev/null @@ -1,191 +0,0 @@ -/* - * Copyright 2010-2012 Freescale Semiconductor, Inc. - * - * Authors: Roy Zang <tie-fei.zang@freescale.com> - * Chunhe Lan <b25806@freescale.com> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <command.h> -#include <pci.h> -#include <asm/io.h> -#include <asm/cache.h> -#include <asm/processor.h> -#include <asm/mmu.h> -#include <asm/immap_85xx.h> -#include <asm/fsl_pci.h> -#include <fsl_ddr_sdram.h> -#include <asm/fsl_portals.h> -#include <libfdt.h> -#include <fdt_support.h> -#include <netdev.h> -#include <malloc.h> -#include <fm_eth.h> -#include <fsl_mdio.h> -#include <miiphy.h> -#include <phy.h> -#include <asm/fsl_dtsec.h> - -#include "bcsr.h" - -DECLARE_GLOBAL_DATA_PTR; - -int board_early_init_f(void) -{ - fsl_lbc_t *lbc = LBC_BASE_ADDR; - - /* Set ABSWP to implement conversion of addresses in the LBC */ - setbits_be32(&lbc->lbcr, CONFIG_SYS_LBC_LBCR); - - return 0; -} - -int checkboard(void) -{ - u8 *bcsr = (u8 *)BCSR_ACCESS_REG_ADDR; - - printf("Board: P1023 RDS\n"); - - clrbits_8(&bcsr[15], BCSR15_I2C_BUS0_SEG_CLR); - setbits_8(&bcsr[15], BCSR15_I2C_BUS0_SEG0); - - return 0; -} - -/* Fixed sdram init -- doesn't use serial presence detect. */ -phys_size_t fixed_sdram(void) -{ -#ifndef CONFIG_SYS_RAMBOOT - struct ccsr_ddr __iomem *ddr = - (struct ccsr_ddr __iomem *)CONFIG_SYS_FSL_DDR_ADDR; - - set_next_law(0, LAW_SIZE_2G, LAW_TRGT_IF_DDR_1); - - out_be32(&ddr->cs0_bnds, CONFIG_SYS_DDR_CS0_BNDS); - out_be32(&ddr->cs0_config, CONFIG_SYS_DDR_CS0_CONFIG); - out_be32(&ddr->cs1_bnds, CONFIG_SYS_DDR_CS1_BNDS); - out_be32(&ddr->cs1_config, CONFIG_SYS_DDR_CS1_CONFIG); - out_be32(&ddr->timing_cfg_3, CONFIG_SYS_DDR_TIMING_3); - out_be32(&ddr->timing_cfg_0, CONFIG_SYS_DDR_TIMING_0); - out_be32(&ddr->timing_cfg_1, CONFIG_SYS_DDR_TIMING_1); - out_be32(&ddr->timing_cfg_2, CONFIG_SYS_DDR_TIMING_2); - out_be32(&ddr->sdram_cfg_2, CONFIG_SYS_DDR_CONTROL2); - out_be32(&ddr->sdram_mode, CONFIG_SYS_DDR_MODE_1); - out_be32(&ddr->sdram_mode_2, CONFIG_SYS_DDR_MODE_2); - out_be32(&ddr->sdram_interval, CONFIG_SYS_DDR_INTERVAL); - out_be32(&ddr->sdram_data_init, CONFIG_SYS_DDR_DATA_INIT); - out_be32(&ddr->sdram_clk_cntl, CONFIG_SYS_DDR_CLK_CTRL); - out_be32(&ddr->timing_cfg_4, CONFIG_SYS_DDR_TIMING_4); - out_be32(&ddr->timing_cfg_5, CONFIG_SYS_DDR_TIMING_5); - out_be32(&ddr->ddr_zq_cntl, CONFIG_SYS_DDR_ZQ_CNTL); - out_be32(&ddr->ddr_wrlvl_cntl, CONFIG_SYS_DDR_WRLVL_CNTL); - out_be32(&ddr->ddr_cdr1, CONFIG_SYS_DDR_CDR_1); - out_be32(&ddr->ddr_cdr2, CONFIG_SYS_DDR_CDR_2); - out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL); -#endif - return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024ul; -} - -#ifdef CONFIG_PCI -void pci_init_board(void) -{ - fsl_pcie_init_board(0); -} -#endif - -int board_early_init_r(void) -{ - const unsigned int flashbase = CONFIG_SYS_BCSR_BASE; - const u8 flash_esel = find_tlb_idx((void *)flashbase, 1); - - /* - * Remap Boot flash + BCSR region to caching-inhibited - * so that flash can be erased properly. - */ - - /* Flush d-cache and invalidate i-cache of any FLASH data */ - flush_dcache(); - invalidate_icache(); - - /* invalidate existing TLB entry for flash + bcsr */ - disable_tlb(flash_esel); - - set_tlb(1, flashbase, CONFIG_SYS_BCSR_BASE_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, flash_esel, BOOKE_PAGESZ_256M, 1); - - setup_portals(); - - return 0; -} - -unsigned long get_board_sys_clk(ulong dummy) -{ - return gd->bus_clk; -} - -unsigned long get_board_ddr_clk(ulong dummy) -{ - return gd->mem_clk; -} - -int board_eth_init(bd_t *bis) -{ - u8 *bcsr = (u8 *)BCSR_ACCESS_REG_ADDR; - ccsr_gur_t *gur = (ccsr_gur_t *)CONFIG_SYS_MPC85xx_GUTS_ADDR; - struct fsl_pq_mdio_info dtsec_mdio_info; - - /* - * Need to set dTSEC 1 pin multiplexing to TSEC. The default setting - * is not correct. - */ - setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_TSEC1_1); - - dtsec_mdio_info.regs = - (struct tsec_mii_mng *)CONFIG_SYS_FM1_DTSEC1_MDIO_ADDR; - dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME; - - /* Register the 1G MDIO bus */ - fsl_pq_mdio_init(bis, &dtsec_mdio_info); - - fm_info_set_phy_address(FM1_DTSEC1, CONFIG_SYS_FM1_DTSEC1_PHY_ADDR); - fm_info_set_phy_address(FM1_DTSEC2, CONFIG_SYS_FM1_DTSEC2_PHY_ADDR); - - fm_info_set_mdio(FM1_DTSEC1, - miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME)); - fm_info_set_mdio(FM1_DTSEC2, - miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME)); - - /* Make SERDES connected to SGMII by cleaing bcsr19[7] */ - if (fm_info_get_enet_if(FM1_DTSEC1) == PHY_INTERFACE_MODE_SGMII) - clrbits_8(&bcsr[19], BCSR19_SGMII_SEL_L); - -#ifdef CONFIG_FMAN_ENET - cpu_eth_init(bis); -#endif - - return pci_eth_init(bis); -} - -#if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) -{ - phys_addr_t base; - phys_size_t size; - - ft_cpu_setup(blob, bd); - - base = getenv_bootm_low(); - size = getenv_bootm_size(); - - fdt_fixup_memory(blob, (u64)base, (u64)size); - -#ifdef CONFIG_HAS_FSL_DR_USB - fdt_fixup_dr_usb(blob, bd); -#endif - - fdt_fixup_fman_ethernet(blob); -} -#endif diff --git a/board/freescale/p1023rds/tlb.c b/board/freescale/p1023rds/tlb.c deleted file mode 100644 index 3c92c14ae3..0000000000 --- a/board/freescale/p1023rds/tlb.c +++ /dev/null @@ -1,100 +0,0 @@ -/* - * Copyright 2010-2011 Freescale Semiconductor, Inc. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <asm/mmu.h> - -struct fsl_e_tlb_entry tlb_table[] = { - /* TLB 0 - for temp stack in cache */ - SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 0, BOOKE_PAGESZ_4K, 0), - SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, - CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 0, BOOKE_PAGESZ_4K, 0), - SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, - CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 0, BOOKE_PAGESZ_4K, 0), - SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, - CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 0, BOOKE_PAGESZ_4K, 0), - - /* TLB 1 */ - /* *I*** - Covers boot page */ - SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I, - 0, 0, BOOKE_PAGESZ_4K, 1), - - /* *I*G* - CCSRBAR */ - SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 1, BOOKE_PAGESZ_4M, 1), - - /* *W*G* - BCSR and NOR flash on local bus*/ - /* This will be changed to *I*G* after relocation to RAM. */ - SET_TLB_ENTRY(1, CONFIG_SYS_BCSR_BASE, CONFIG_SYS_BCSR_BASE_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G, - 0, 2, BOOKE_PAGESZ_256M, 1), - - /* *I*G* - PCI */ - SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT, CONFIG_SYS_PCIE3_MEM_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 3, BOOKE_PAGESZ_1G, 1), - - /* *I*G* - PCI */ - SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT + 0x40000000, - CONFIG_SYS_PCIE3_MEM_PHYS + 0x40000000, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 4, BOOKE_PAGESZ_256M, 1), - - SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT + 0x50000000, - CONFIG_SYS_PCIE3_MEM_PHYS + 0x50000000, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 5, BOOKE_PAGESZ_256M, 1), - - /* *I*G* - PCI I/O */ - SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_IO_VIRT, CONFIG_SYS_PCIE3_IO_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 6, BOOKE_PAGESZ_256K, 1), - - /* Bman/Qman */ - SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 7, BOOKE_PAGESZ_1M, 1), - SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x00100000, - CONFIG_SYS_BMAN_MEM_PHYS + 0x00100000, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 8, BOOKE_PAGESZ_1M, 1), - SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_M, - 0, 9, BOOKE_PAGESZ_1M, 1), - SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x00100000, - CONFIG_SYS_QMAN_MEM_PHYS + 0x00100000, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 10, BOOKE_PAGESZ_1M, 1), - - /* *I*G - NAND */ - SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 11, BOOKE_PAGESZ_1M, 1), - -#ifdef CONFIG_SYS_RAMBOOT - SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, - CONFIG_SYS_DDR_SDRAM_BASE, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 12, BOOKE_PAGESZ_1G, 1), - - SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000, - CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 13, BOOKE_PAGESZ_1G, 1), -#endif -}; - -int num_tlb_entries = ARRAY_SIZE(tlb_table); |