summaryrefslogtreecommitdiff
path: root/board/freescale
diff options
context:
space:
mode:
Diffstat (limited to 'board/freescale')
-rw-r--r--board/freescale/mx25pdk/mx25pdk.c121
-rw-r--r--board/freescale/mx31ads/u-boot.lds2
-rw-r--r--board/freescale/mx31pdk/mx31pdk.c9
-rw-r--r--board/freescale/mx35pdk/lowlevel_init.S4
-rw-r--r--board/freescale/mx35pdk/mx35pdk.c23
-rw-r--r--board/freescale/mx51evk/mx51evk.c2
-rw-r--r--board/freescale/mx51evk/mx51evk_video.c39
-rw-r--r--board/freescale/mx53loco/mx53loco.c84
-rw-r--r--board/freescale/mx53loco/mx53loco_video.c38
-rw-r--r--board/freescale/mx6qsabresd/mx6qsabresd.c80
10 files changed, 359 insertions, 43 deletions
diff --git a/board/freescale/mx25pdk/mx25pdk.c b/board/freescale/mx25pdk/mx25pdk.c
index 4a8352fb3d..d73e27e540 100644
--- a/board/freescale/mx25pdk/mx25pdk.c
+++ b/board/freescale/mx25pdk/mx25pdk.c
@@ -19,12 +19,71 @@
#include <common.h>
#include <asm/io.h>
+#include <asm/gpio.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/imx25-pinmux.h>
#include <asm/arch/sys_proto.h>
+#include <asm/arch/clock.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <i2c.h>
+#include <power/pmic.h>
+#include <fsl_pmic.h>
+#include <mc34704.h>
+
+#define FEC_RESET_B IMX_GPIO_NR(2, 3)
+#define FEC_ENABLE_B IMX_GPIO_NR(4, 8)
+#define CARD_DETECT IMX_GPIO_NR(2, 1)
DECLARE_GLOBAL_DATA_PTR;
+#ifdef CONFIG_FSL_ESDHC
+struct fsl_esdhc_cfg esdhc_cfg[1] = {
+ {IMX_MMC_SDHC1_BASE},
+};
+#endif
+
+static void mx25pdk_fec_init(void)
+{
+ struct iomuxc_mux_ctl *muxctl;
+ struct iomuxc_pad_ctl *padctl;
+ u32 gpio_mux_mode = MX25_PIN_MUX_MODE(5);
+ u32 gpio_mux_mode0_sion = MX25_PIN_MUX_MODE(0) | MX25_PIN_MUX_SION;
+
+ /* FEC pin init is generic */
+ mx25_fec_init_pins();
+
+ muxctl = (struct iomuxc_mux_ctl *)IMX_IOPADMUX_BASE;
+ padctl = (struct iomuxc_pad_ctl *)IMX_IOPADCTL_BASE;
+ /*
+ * Set up FEC_RESET_B and FEC_ENABLE_B
+ *
+ * FEC_RESET_B: gpio2_3 is ALT 5 mode of pin D12
+ * FEC_ENABLE_B: gpio4_8 is ALT 5 mode of pin A17
+ */
+ writel(gpio_mux_mode, &muxctl->pad_d12);
+ writel(gpio_mux_mode, &muxctl->pad_a17);
+
+ writel(0x0, &padctl->pad_d12);
+ writel(0x0, &padctl->pad_a17);
+
+ /* Assert RESET and ENABLE low */
+ gpio_direction_output(FEC_RESET_B, 0);
+ gpio_direction_output(FEC_ENABLE_B, 0);
+
+ udelay(10);
+
+ /* Deassert RESET and ENABLE */
+ gpio_set_value(FEC_RESET_B, 1);
+ gpio_set_value(FEC_ENABLE_B, 1);
+
+ /* Setup I2C pins so that PMIC can turn on PHY supply */
+ writel(gpio_mux_mode0_sion, &muxctl->pad_i2c1_clk);
+ writel(gpio_mux_mode0_sion, &muxctl->pad_i2c1_dat);
+ writel(0x1E8, &padctl->pad_i2c1_clk);
+ writel(0x1E8, &padctl->pad_i2c1_dat);
+}
+
int dram_init(void)
{
/* dram_init must store complete ramsize in gd->ram_size */
@@ -48,6 +107,68 @@ int board_init(void)
return 0;
}
+int board_late_init(void)
+{
+ struct pmic *p;
+ int ret;
+
+ mx25pdk_fec_init();
+
+ ret = pmic_init(I2C_PMIC);
+ if (ret)
+ return ret;
+
+ p = pmic_get("FSL_PMIC");
+ if (!p)
+ return -ENODEV;
+
+ /* Turn on Ethernet PHY supply */
+ pmic_reg_write(p, MC34704_GENERAL2_REG, ONOFFE);
+
+ return 0;
+}
+
+#ifdef CONFIG_FSL_ESDHC
+int board_mmc_getcd(struct mmc *mmc)
+{
+ struct iomuxc_mux_ctl *muxctl;
+ struct iomuxc_pad_ctl *padctl;
+ u32 gpio_mux_mode = MX25_PIN_MUX_MODE(5);
+
+ /*
+ * Set up the Card Detect pin.
+ *
+ * SD1_GPIO_CD: gpio2_1 is ALT 5 mode of pin A15
+ *
+ */
+ muxctl = (struct iomuxc_mux_ctl *)IMX_IOPADMUX_BASE;
+ padctl = (struct iomuxc_pad_ctl *)IMX_IOPADCTL_BASE;
+
+ writel(gpio_mux_mode, &muxctl->pad_a15);
+ writel(0x0, &padctl->pad_a15);
+
+ gpio_direction_input(CARD_DETECT);
+ return !gpio_get_value(CARD_DETECT);
+}
+
+int board_mmc_init(bd_t *bis)
+{
+ struct iomuxc_mux_ctl *muxctl;
+ u32 sdhc1_mux_mode = MX25_PIN_MUX_MODE(0) | MX25_PIN_MUX_SION;
+
+ muxctl = (struct iomuxc_mux_ctl *)IMX_IOPADMUX_BASE;
+ writel(sdhc1_mux_mode, &muxctl->pad_sd1_cmd);
+ writel(sdhc1_mux_mode, &muxctl->pad_sd1_clk);
+ writel(sdhc1_mux_mode, &muxctl->pad_sd1_data0);
+ writel(sdhc1_mux_mode, &muxctl->pad_sd1_data1);
+ writel(sdhc1_mux_mode, &muxctl->pad_sd1_data2);
+ writel(sdhc1_mux_mode, &muxctl->pad_sd1_data3);
+
+ esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC1_CLK);
+ return fsl_esdhc_initialize(bis, &esdhc_cfg[0]);
+}
+#endif
+
int checkboard(void)
{
puts("Board: MX25PDK\n");
diff --git a/board/freescale/mx31ads/u-boot.lds b/board/freescale/mx31ads/u-boot.lds
index 29ad0e6e79..52677299e8 100644
--- a/board/freescale/mx31ads/u-boot.lds
+++ b/board/freescale/mx31ads/u-boot.lds
@@ -65,6 +65,8 @@ SECTIONS
. = ALIGN(4);
+ __image_copy_end = .;
+
.rel.dyn : {
__rel_dyn_start = .;
*(.rel*)
diff --git a/board/freescale/mx31pdk/mx31pdk.c b/board/freescale/mx31pdk/mx31pdk.c
index bc60632aa0..895396cd62 100644
--- a/board/freescale/mx31pdk/mx31pdk.c
+++ b/board/freescale/mx31pdk/mx31pdk.c
@@ -36,13 +36,6 @@
DECLARE_GLOBAL_DATA_PTR;
-#ifdef CONFIG_HW_WATCHDOG
-void hw_watchdog_reset(void)
-{
- mxc_hw_watchdog_reset();
-}
-#endif
-
int dram_init(void)
{
/* dram_init must store complete ramsize in gd->ram_size */
@@ -98,7 +91,7 @@ int board_late_init(void)
pmic_reg_write(p, REG_POWER_CTL0, val | COINCHEN);
pmic_reg_write(p, REG_INT_STATUS1, RTCRSTI);
#ifdef CONFIG_HW_WATCHDOG
- mxc_hw_watchdog_enable();
+ hw_watchdog_init();
#endif
return 0;
}
diff --git a/board/freescale/mx35pdk/lowlevel_init.S b/board/freescale/mx35pdk/lowlevel_init.S
index 75bb958619..da8b6f3a4e 100644
--- a/board/freescale/mx35pdk/lowlevel_init.S
+++ b/board/freescale/mx35pdk/lowlevel_init.S
@@ -94,6 +94,10 @@
orr r1, r1, #0x00000C00
orr r1, r1, #0x00000003
str r1, [r0, #CLKCTL_CGR1]
+
+ ldr r1, [r0, #CLKCTL_CGR2]
+ orr r1, r1, #0x00C00000
+ str r1, [r0, #CLKCTL_CGR2]
.endm
.macro setup_sdram
diff --git a/board/freescale/mx35pdk/mx35pdk.c b/board/freescale/mx35pdk/mx35pdk.c
index c835b0edeb..b7f474e5ef 100644
--- a/board/freescale/mx35pdk/mx35pdk.c
+++ b/board/freescale/mx35pdk/mx35pdk.c
@@ -98,6 +98,26 @@ static void setup_iomux_spi(void)
mxc_request_iomux(MX35_PIN_CSPI1_SCLK, MUX_CONFIG_SION);
}
+static void setup_iomux_usbotg(void)
+{
+ int in_pad, out_pad;
+
+ /* Set up pins for USBOTG. */
+ mxc_request_iomux(MX35_PIN_USBOTG_PWR,
+ MUX_CONFIG_SION | MUX_CONFIG_FUNC);
+ mxc_request_iomux(MX35_PIN_USBOTG_OC,
+ MUX_CONFIG_SION | MUX_CONFIG_FUNC);
+
+ in_pad = PAD_CTL_DRV_3_3V | PAD_CTL_HYS_SCHMITZ | PAD_CTL_PKE_ENABLE |
+ PAD_CTL_PUE_PUD | PAD_CTL_100K_PD | PAD_CTL_ODE_CMOS |
+ PAD_CTL_DRV_NORMAL | PAD_CTL_SRE_SLOW;
+ out_pad = PAD_CTL_DRV_3_3V | PAD_CTL_HYS_CMOS | PAD_CTL_PKE_NONE |
+ PAD_CTL_ODE_CMOS | PAD_CTL_DRV_NORMAL | PAD_CTL_SRE_SLOW;
+
+ mxc_iomux_set_pad(MX35_PIN_USBOTG_PWR, out_pad);
+ mxc_iomux_set_pad(MX35_PIN_USBOTG_OC, in_pad);
+}
+
static void setup_iomux_fec(void)
{
int pad;
@@ -189,6 +209,7 @@ int board_early_init_f(void)
__raw_writel(readl(&ccm->rcsr) | MXC_CCM_RCSR_NFC_FMS, &ccm->rcsr);
setup_iomux_i2c();
+ setup_iomux_usbotg();
setup_iomux_fec();
setup_iomux_spi();
@@ -253,7 +274,7 @@ int board_late_init(void)
mxc_request_iomux(MX35_PIN_COMPARE, MUX_CONFIG_GPIO);
mxc_iomux_set_input(MUX_IN_GPIO1_IN_5, INPUT_CTL_PATH0);
- gpio_direction_output(37, 1);
+ gpio_direction_output(IMX_GPIO_NR(2, 5), 1);
}
val = mc9sdz60_reg_read(MC9SDZ60_REG_GPIO_1) | 0x04;
diff --git a/board/freescale/mx51evk/mx51evk.c b/board/freescale/mx51evk/mx51evk.c
index d1ef431895..54c16b1f9d 100644
--- a/board/freescale/mx51evk/mx51evk.c
+++ b/board/freescale/mx51evk/mx51evk.c
@@ -489,8 +489,6 @@ int board_init(void)
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
- lcd_enable();
-
return 0;
}
diff --git a/board/freescale/mx51evk/mx51evk_video.c b/board/freescale/mx51evk/mx51evk_video.c
index f036cf73b2..7be5c9befc 100644
--- a/board/freescale/mx51evk/mx51evk_video.c
+++ b/board/freescale/mx51evk/mx51evk_video.c
@@ -48,6 +48,22 @@ static struct fb_videomode const claa_wvga = {
.vmode = FB_VMODE_NONINTERLACED
};
+static struct fb_videomode const dvi = {
+ .name = "DVI panel",
+ .refresh = 60,
+ .xres = 1024,
+ .yres = 768,
+ .pixclock = 15385,
+ .left_margin = 220,
+ .right_margin = 40,
+ .upper_margin = 21,
+ .lower_margin = 7,
+ .hsync_len = 60,
+ .vsync_len = 10,
+ .sync = 0,
+ .vmode = FB_VMODE_NONINTERLACED
+};
+
void setup_iomux_lcd(void)
{
/* DI2_PIN15 */
@@ -73,9 +89,26 @@ void setup_iomux_lcd(void)
gpio_direction_output(MX51EVK_LCD_BACKLIGHT, 1);
}
-void lcd_enable(void)
+int board_video_skip(void)
{
- int ret = ipuv3_fb_init(&claa_wvga, 1, IPU_PIX_FMT_RGB565);
+ int ret;
+ char const *e = getenv("panel");
+
+ if (e) {
+ if (strcmp(e, "claa") == 0) {
+ ret = ipuv3_fb_init(&claa_wvga, 1, IPU_PIX_FMT_RGB565);
+ if (ret)
+ printf("claa cannot be configured: %d\n", ret);
+ return ret;
+ }
+ }
+
+ /*
+ * 'panel' env variable not found or has different value than 'claa'
+ * Defaulting to dvi output.
+ */
+ ret = ipuv3_fb_init(&dvi, 0, IPU_PIX_FMT_RGB24);
if (ret)
- printf("LCD cannot be configured: %d\n", ret);
+ printf("dvi cannot be configured: %d\n", ret);
+ return ret;
}
diff --git a/board/freescale/mx53loco/mx53loco.c b/board/freescale/mx53loco/mx53loco.c
index 81c511cdc1..8f39c383f1 100644
--- a/board/freescale/mx53loco/mx53loco.c
+++ b/board/freescale/mx53loco/mx53loco.c
@@ -343,14 +343,13 @@ static void setup_iomux_i2c(void)
static int power_init(void)
{
unsigned int val;
- int ret = -1;
+ int ret;
struct pmic *p;
- int retval;
if (!i2c_probe(CONFIG_SYS_DIALOG_PMIC_I2C_ADDR)) {
- retval = pmic_dialog_init(I2C_PMIC);
- if (retval)
- return retval;
+ ret = pmic_dialog_init(I2C_PMIC);
+ if (ret)
+ return ret;
p = pmic_get("DIALOG_PMIC");
if (!p)
@@ -359,22 +358,41 @@ static int power_init(void)
/* Set VDDA to 1.25V */
val = DA9052_BUCKCORE_BCOREEN | DA_BUCKCORE_VBCORE_1_250V;
ret = pmic_reg_write(p, DA9053_BUCKCORE_REG, val);
+ if (ret) {
+ printf("Writing to BUCKCORE_REG failed: %d\n", ret);
+ return ret;
+ }
- ret |= pmic_reg_read(p, DA9053_SUPPLY_REG, &val);
+ pmic_reg_read(p, DA9053_SUPPLY_REG, &val);
val |= DA9052_SUPPLY_VBCOREGO;
- ret |= pmic_reg_write(p, DA9053_SUPPLY_REG, val);
+ ret = pmic_reg_write(p, DA9053_SUPPLY_REG, val);
+ if (ret) {
+ printf("Writing to SUPPLY_REG failed: %d\n", ret);
+ return ret;
+ }
/* Set Vcc peripheral to 1.30V */
- ret |= pmic_reg_write(p, DA9053_BUCKPRO_REG, 0x62);
- ret |= pmic_reg_write(p, DA9053_SUPPLY_REG, 0x62);
+ ret = pmic_reg_write(p, DA9053_BUCKPRO_REG, 0x62);
+ if (ret) {
+ printf("Writing to BUCKPRO_REG failed: %d\n", ret);
+ return ret;
+ }
+
+ ret = pmic_reg_write(p, DA9053_SUPPLY_REG, 0x62);
+ if (ret) {
+ printf("Writing to SUPPLY_REG failed: %d\n", ret);
+ return ret;
+ }
+
+ return ret;
}
if (!i2c_probe(CONFIG_SYS_FSL_PMIC_I2C_ADDR)) {
- retval = pmic_init(I2C_PMIC);
- if (retval)
- return retval;
+ ret = pmic_init(I2C_PMIC);
+ if (ret)
+ return ret;
- p = pmic_get("DIALOG_PMIC");
+ p = pmic_get("FSL_PMIC");
if (!p)
return -ENODEV;
@@ -382,28 +400,50 @@ static int power_init(void)
pmic_reg_read(p, REG_SW_0, &val);
val = (val & ~SWx_VOLT_MASK_MC34708) | SWx_1_250V_MC34708;
ret = pmic_reg_write(p, REG_SW_0, val);
+ if (ret) {
+ printf("Writing to REG_SW_0 failed: %d\n", ret);
+ return ret;
+ }
/* Set VCC as 1.30V on SW2 */
pmic_reg_read(p, REG_SW_1, &val);
val = (val & ~SWx_VOLT_MASK_MC34708) | SWx_1_300V_MC34708;
- ret |= pmic_reg_write(p, REG_SW_1, val);
+ ret = pmic_reg_write(p, REG_SW_1, val);
+ if (ret) {
+ printf("Writing to REG_SW_1 failed: %d\n", ret);
+ return ret;
+ }
/* Set global reset timer to 4s */
pmic_reg_read(p, REG_POWER_CTL2, &val);
val = (val & ~TIMER_MASK_MC34708) | TIMER_4S_MC34708;
- ret |= pmic_reg_write(p, REG_POWER_CTL2, val);
+ ret = pmic_reg_write(p, REG_POWER_CTL2, val);
+ if (ret) {
+ printf("Writing to REG_POWER_CTL2 failed: %d\n", ret);
+ return ret;
+ }
/* Set VUSBSEL and VUSBEN for USB PHY supply*/
pmic_reg_read(p, REG_MODE_0, &val);
val |= (VUSBSEL_MC34708 | VUSBEN_MC34708);
- ret |= pmic_reg_write(p, REG_MODE_0, val);
+ ret = pmic_reg_write(p, REG_MODE_0, val);
+ if (ret) {
+ printf("Writing to REG_MODE_0 failed: %d\n", ret);
+ return ret;
+ }
/* Set SWBST to 5V in auto mode */
val = SWBST_AUTO;
- ret |= pmic_reg_write(p, SWBST_CTRL, val);
+ ret = pmic_reg_write(p, SWBST_CTRL, val);
+ if (ret) {
+ printf("Writing to SWBST_CTRL failed: %d\n", ret);
+ return ret;
+ }
+
+ return ret;
}
- return ret;
+ return -1;
}
static void clock_1GHz(void)
@@ -462,12 +502,16 @@ int board_init(void)
mxc_set_sata_internal_clock();
setup_iomux_i2c();
+
+ return 0;
+}
+
+int board_late_init(void)
+{
if (!power_init())
clock_1GHz();
print_cpuinfo();
- lcd_enable();
-
return 0;
}
diff --git a/board/freescale/mx53loco/mx53loco_video.c b/board/freescale/mx53loco/mx53loco_video.c
index 69991e8511..a4d5a6a365 100644
--- a/board/freescale/mx53loco/mx53loco_video.c
+++ b/board/freescale/mx53loco/mx53loco_video.c
@@ -46,6 +46,21 @@ static struct fb_videomode const claa_wvga = {
.vmode = FB_VMODE_NONINTERLACED
};
+static struct fb_videomode const seiko_wvga = {
+ .name = "Seiko-43WVF1G",
+ .refresh = 60,
+ .xres = 800,
+ .yres = 480,
+ .pixclock = 29851, /* picosecond (33.5 MHz) */
+ .left_margin = 89,
+ .right_margin = 164,
+ .upper_margin = 23,
+ .lower_margin = 10,
+ .hsync_len = 10,
+ .vsync_len = 10,
+ .sync = 0,
+};
+
void setup_iomux_lcd(void)
{
mxc_request_iomux(MX53_PIN_DI0_DISP_CLK, IOMUX_CONFIG_ALT0);
@@ -86,9 +101,26 @@ void setup_iomux_lcd(void)
gpio_direction_output(IOMUX_TO_GPIO(MX53_PIN_GPIO_1), 1);
}
-void lcd_enable(void)
+int board_video_skip(void)
{
- int ret = ipuv3_fb_init(&claa_wvga, 0, IPU_PIX_FMT_RGB565);
+ int ret;
+ char const *e = getenv("panel");
+
+ if (e) {
+ if (strcmp(e, "seiko") == 0) {
+ ret = ipuv3_fb_init(&seiko_wvga, 0, IPU_PIX_FMT_RGB24);
+ if (ret)
+ printf("Seiko cannot be configured: %d\n", ret);
+ return ret;
+ }
+ }
+
+ /*
+ * 'panel' env variable not found or has different value than 'seiko'
+ * Defaulting to claa lcd.
+ */
+ ret = ipuv3_fb_init(&claa_wvga, 0, IPU_PIX_FMT_RGB565);
if (ret)
- printf("LCD cannot be configured: %d\n", ret);
+ printf("CLAA cannot be configured: %d\n", ret);
+ return ret;
}
diff --git a/board/freescale/mx6qsabresd/mx6qsabresd.c b/board/freescale/mx6qsabresd/mx6qsabresd.c
index 0240fb5479..65c4a1a4f3 100644
--- a/board/freescale/mx6qsabresd/mx6qsabresd.c
+++ b/board/freescale/mx6qsabresd/mx6qsabresd.c
@@ -86,6 +86,20 @@ static void setup_iomux_enet(void)
gpio_set_value(IMX_GPIO_NR(1, 25), 1);
}
+iomux_v3_cfg_t const usdhc2_pads[] = {
+ MX6Q_PAD_SD2_CLK__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6Q_PAD_SD2_CMD__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6Q_PAD_SD2_DAT0__USDHC2_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6Q_PAD_SD2_DAT1__USDHC2_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6Q_PAD_SD2_DAT2__USDHC2_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6Q_PAD_SD2_DAT3__USDHC2_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6Q_PAD_NANDF_D4__USDHC2_DAT4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6Q_PAD_NANDF_D5__USDHC2_DAT5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6Q_PAD_NANDF_D6__USDHC2_DAT6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6Q_PAD_NANDF_D7__USDHC2_DAT7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6Q_PAD_NANDF_D2__GPIO_2_2 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
+};
+
iomux_v3_cfg_t const usdhc3_pads[] = {
MX6Q_PAD_SD3_CLK__USDHC3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6Q_PAD_SD3_CMD__USDHC3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
@@ -100,28 +114,82 @@ iomux_v3_cfg_t const usdhc3_pads[] = {
MX6Q_PAD_NANDF_D0__GPIO_2_0 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
};
+iomux_v3_cfg_t const usdhc4_pads[] = {
+ MX6Q_PAD_SD4_CLK__USDHC4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6Q_PAD_SD4_CMD__USDHC4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6Q_PAD_SD4_DAT0__USDHC4_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6Q_PAD_SD4_DAT1__USDHC4_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6Q_PAD_SD4_DAT2__USDHC4_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6Q_PAD_SD4_DAT3__USDHC4_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6Q_PAD_SD4_DAT4__USDHC4_DAT4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6Q_PAD_SD4_DAT5__USDHC4_DAT5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6Q_PAD_SD4_DAT6__USDHC4_DAT6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6Q_PAD_SD4_DAT7__USDHC4_DAT7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
static void setup_iomux_uart(void)
{
imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
}
#ifdef CONFIG_FSL_ESDHC
-struct fsl_esdhc_cfg usdhc_cfg[1] = {
+struct fsl_esdhc_cfg usdhc_cfg[3] = {
+ {USDHC2_BASE_ADDR},
{USDHC3_BASE_ADDR},
+ {USDHC4_BASE_ADDR},
};
+#define USDHC2_CD_GPIO IMX_GPIO_NR(2, 2)
+#define USDHC3_CD_GPIO IMX_GPIO_NR(2, 0)
+
int board_mmc_getcd(struct mmc *mmc)
{
- gpio_direction_input(IMX_GPIO_NR(2, 0));
- return !gpio_get_value(IMX_GPIO_NR(2, 0));
+ struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+
+ switch (cfg->esdhc_base) {
+ case USDHC2_BASE_ADDR:
+ return !gpio_get_value(USDHC2_CD_GPIO);
+ case USDHC3_BASE_ADDR:
+ return !gpio_get_value(USDHC3_CD_GPIO);
+ default:
+ return 1; /* eMMC/uSDHC4 is always present */
+ }
}
int board_mmc_init(bd_t *bis)
{
- imx_iomux_v3_setup_multiple_pads(usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
+ int i;
+
+ for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+ switch (i) {
+ case 0:
+ imx_iomux_v3_setup_multiple_pads(
+ usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+ gpio_direction_input(USDHC2_CD_GPIO);
+ usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+ break;
+ case 1:
+ imx_iomux_v3_setup_multiple_pads(
+ usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
+ gpio_direction_input(USDHC3_CD_GPIO);
+ usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+ break;
+ case 2:
+ imx_iomux_v3_setup_multiple_pads(
+ usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
+ usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
+ break;
+ default:
+ printf("Warning: you configured more USDHC controllers"
+ "(%d) than supported by the board\n", i + 1);
+ return 0;
+ }
+
+ if (fsl_esdhc_initialize(bis, &usdhc_cfg[i]))
+ printf("Warning: failed to initialize mmc dev %d\n", i);
+ }
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
- return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
+ return 0;
}
#endif
generated by cgit (git 2.34.1) at 2024-12-28 01:50:46 +0000