1 files changed, 279 insertions, 0 deletions
diff --git a/board/gdsys/a38x/controlcenterdc.c b/board/gdsys/a38x/controlcenterdc.c
new file mode 100644
index 0000000000..f0efb53447
--- /dev/null
+++ b/board/gdsys/a38x/controlcenterdc.c
@@ -0,0 +1,279 @@
+/*
+ * Copyright (C) 2015 Stefan Roese <sr@denx.de>
+ * Copyright (C) 2016 Mario Six <mario.six@gdsys.cc>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <miiphy.h>
+#include <tpm.h>
+#include <asm/io.h>
+#include <asm/arch/cpu.h>
+#include <asm-generic/gpio.h>
+
+#include "../drivers/ddr/marvell/a38x/ddr3_a38x_topology.h"
+#include "../arch/arm/mach-mvebu/serdes/a38x/high_speed_env_spec.h"
+
+#include "keyprogram.h"
+#include "dt_helpers.h"
+#include "hydra.h"
+#include "ihs_phys.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define ETH_PHY_CTRL_REG		0
+#define ETH_PHY_CTRL_POWER_DOWN_BIT	11
+#define ETH_PHY_CTRL_POWER_DOWN_MASK	(1 << ETH_PHY_CTRL_POWER_DOWN_BIT)
+
+#define DB_GP_88F68XX_GPP_OUT_ENA_LOW	0x7fffffff
+#define DB_GP_88F68XX_GPP_OUT_ENA_MID	0xffffefff
+
+#define DB_GP_88F68XX_GPP_OUT_VAL_LOW	0x0
+#define DB_GP_88F68XX_GPP_OUT_VAL_MID	0x00001000
+#define DB_GP_88F68XX_GPP_POL_LOW	0x0
+#define DB_GP_88F68XX_GPP_POL_MID	0x0
+
+/*
+ * Define the DDR layout / topology here in the board file. This will
+ * be used by the DDR3 init code in the SPL U-Boot version to configure
+ * the DDR3 controller.
+ */
+static struct hws_topology_map ddr_topology_map = {
+	0x1, /* active interfaces */
+	/* cs_mask, mirror, dqs_swap, ck_swap X PUPs */
+	{ { { {0x1, 0, 0, 0},
+	      {0x1, 0, 0, 0},
+	      {0x1, 0, 0, 0},
+	      {0x1, 0, 0, 0},
+	      {0x1, 0, 0, 0} },
+	    SPEED_BIN_DDR_1600K,	/* speed_bin */
+	    BUS_WIDTH_16,		/* memory_width */
+	    MEM_4G,			/* mem_size */
+	    DDR_FREQ_533,		/* frequency */
+	    0, 0,			/* cas_l cas_wl */
+	    HWS_TEMP_LOW} },		/* temperature */
+	5,				/* Num Of Bus Per Interface*/
+	BUS_MASK_32BIT			/* Busses mask */
+};
+
+static struct serdes_map serdes_topology_map[] = {
+	{SGMII0, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+	{USB3_HOST0, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+	/* SATA tx polarity is inverted */
+	{SATA1, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 1},
+	{SGMII2, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+	{DEFAULT_SERDES, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+	{PEX2, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0}
+};
+
+int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count)
+{
+	*serdes_map_array = serdes_topology_map;
+	*count = ARRAY_SIZE(serdes_topology_map);
+	return 0;
+}
+
+void board_pex_config(void)
+{
+#ifdef CONFIG_SPL_BUILD
+	uint k;
+	struct gpio_desc gpio = {};
+
+	if (!request_gpio_by_name(&gpio, "pca9698@22", 31, "fpga-program-gpio")) {
+		/* prepare FPGA reconfiguration */
+		dm_gpio_set_dir_flags(&gpio, GPIOD_IS_OUT);
+		dm_gpio_set_value(&gpio, 0);
+
+		/* give lunatic PCIe clock some time to stabilize */
+		mdelay(500);
+
+		/* start FPGA reconfiguration */
+		dm_gpio_set_dir_flags(&gpio, GPIOD_IS_IN);
+	}
+
+	/* wait for FPGA done */
+	if (!request_gpio_by_name(&gpio, "pca9698@22", 19, "fpga-done-gpio")) {
+		for (k = 0; k < 20; ++k) {
+			if (dm_gpio_get_value(&gpio)) {
+				printf("FPGA done after %u rounds\n", k);
+				break;
+			}
+			mdelay(100);
+		}
+	}
+
+	/* disable FPGA reset */
+	if (!request_gpio_by_name(&gpio, "gpio@18100", 6, "cpu-to-fpga-reset")) {
+		dm_gpio_set_dir_flags(&gpio, GPIOD_IS_OUT);
+		dm_gpio_set_value(&gpio, 1);
+	}
+
+	/* wait for FPGA ready */
+	if (!request_gpio_by_name(&gpio, "pca9698@22", 27, "fpga-ready-gpio")) {
+		for (k = 0; k < 2; ++k) {
+			if (!dm_gpio_get_value(&gpio))
+				break;
+			mdelay(100);
+		}
+	}
+#endif
+}
+
+struct hws_topology_map *ddr3_get_topology_map(void)
+{
+	return &ddr_topology_map;
+}
+
+int board_early_init_f(void)
+{
+#ifdef CONFIG_SPL_BUILD
+	/* Configure MPP */
+	writel(0x00111111, MVEBU_MPP_BASE + 0x00);
+	writel(0x40040000, MVEBU_MPP_BASE + 0x04);
+	writel(0x00466444, MVEBU_MPP_BASE + 0x08);
+	writel(0x00043300, MVEBU_MPP_BASE + 0x0c);
+	writel(0x44400000, MVEBU_MPP_BASE + 0x10);
+	writel(0x20000334, MVEBU_MPP_BASE + 0x14);
+	writel(0x40000000, MVEBU_MPP_BASE + 0x18);
+	writel(0x00004444, MVEBU_MPP_BASE + 0x1c);
+
+	/* Set GPP Out value */
+	writel(DB_GP_88F68XX_GPP_OUT_VAL_LOW, MVEBU_GPIO0_BASE + 0x00);
+	writel(DB_GP_88F68XX_GPP_OUT_VAL_MID, MVEBU_GPIO1_BASE + 0x00);
+
+	/* Set GPP Polarity */
+	writel(DB_GP_88F68XX_GPP_POL_LOW, MVEBU_GPIO0_BASE + 0x0c);
+	writel(DB_GP_88F68XX_GPP_POL_MID, MVEBU_GPIO1_BASE + 0x0c);
+
+	/* Set GPP Out Enable */
+	writel(DB_GP_88F68XX_GPP_OUT_ENA_LOW, MVEBU_GPIO0_BASE + 0x04);
+	writel(DB_GP_88F68XX_GPP_OUT_ENA_MID, MVEBU_GPIO1_BASE + 0x04);
+#endif
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* Address of boot parameters */
+	gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
+
+	return 0;
+}
+
+#ifndef CONFIG_SPL_BUILD
+void init_host_phys(struct mii_dev *bus)
+{
+	uint k;
+
+	for (k = 0; k < 2; ++k) {
+		struct phy_device *phydev;
+
+		phydev = phy_find_by_mask(bus, 1 << k,
+					  PHY_INTERFACE_MODE_SGMII);
+
+		if (phydev)
+			phy_config(phydev);
+	}
+}
+
+int ccdc_eth_init(void)
+{
+	uint k;
+	uint octo_phy_mask = 0;
+	int ret;
+	struct mii_dev *bus;
+
+	/* Init SoC's phys */
+	bus = miiphy_get_dev_by_name("ethernet@34000");
+
+	if (bus)
+		init_host_phys(bus);
+
+	bus = miiphy_get_dev_by_name("ethernet@70000");
+
+	if (bus)
+		init_host_phys(bus);
+
+	/* Init octo phys */
+	octo_phy_mask = calculate_octo_phy_mask();
+
+	printf("IHS PHYS: %08x", octo_phy_mask);
+
+	ret = init_octo_phys(octo_phy_mask);
+
+	if (ret)
+		return ret;
+
+	printf("\n");
+
+	if (!get_fpga()) {
+		puts("fpga was NULL\n");
+		return 1;
+	}
+
+	/* reset all FPGA-QSGMII instances */
+	for (k = 0; k < 80; ++k)
+		writel(1 << 31, get_fpga()->qsgmii_port_state[k]);
+
+	udelay(100);
+
+	for (k = 0; k < 80; ++k)
+		writel(0, get_fpga()->qsgmii_port_state[k]);
+	return 0;
+}
+
+#endif
+
+int board_late_init(void)
+{
+#ifndef CONFIG_SPL_BUILD
+	hydra_initialize();
+#endif
+	return 0;
+}
+
+int board_fix_fdt(void *rw_fdt_blob)
+{
+	struct udevice *bus = NULL;
+	uint k;
+	char name[64];
+	int err;
+
+	err = uclass_get_device_by_name(UCLASS_I2C, "i2c@11000", &bus);
+
+	if (err) {
+		printf("Could not get I2C bus.\n");
+		return err;
+	}
+
+	for (k = 0x21; k <= 0x26; k++) {
+		snprintf(name, 64,
+			 "/soc/internal-regs/i2c@11000/pca9698@%02x", k);
+
+		if (!dm_i2c_simple_probe(bus, k))
+			fdt_disable_by_ofname(rw_fdt_blob, name);
+	}
+
+	return 0;
+}
+
+int last_stage_init(void)
+{
+#ifndef CONFIG_SPL_BUILD
+	ccdc_eth_init();
+#endif
+	if (tpm_init() || tpm_startup(TPM_ST_CLEAR) ||
+	    tpm_continue_self_test()) {
+		return 1;
+	}
+
+	mdelay(37);
+
+	flush_keys();
+	load_and_run_keyprog();
+
+	return 0;
+}