diff options
Diffstat (limited to 'board/ge/bx50v3')
| -rw-r--r-- | board/ge/bx50v3/bx50v3.c | 183 |
1 files changed, 138 insertions, 45 deletions
diff --git a/board/ge/bx50v3/bx50v3.c b/board/ge/bx50v3/bx50v3.c index 70c298d2d0..ff8f4d7b97 100644 --- a/board/ge/bx50v3/bx50v3.c +++ b/board/ge/bx50v3/bx50v3.c @@ -25,8 +25,13 @@ #include <asm/io.h> #include <asm/arch/sys_proto.h> #include <i2c.h> +#include <pwm.h> DECLARE_GLOBAL_DATA_PTR; +#define NC_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ + PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \ + PAD_CTL_HYS) + #define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \ PAD_CTL_SRE_FAST | PAD_CTL_HYS) @@ -324,6 +329,8 @@ static iomux_v3_cfg_t const backlight_pads[] = { /* Backlight enable for LVDS display */ MX6_PAD_GPIO_0__GPIO1_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL), #define LVDS_BACKLIGHT_GP IMX_GPIO_NR(1, 0) + /* backlight PWM brightness control */ + MX6_PAD_SD1_DAT3__PWM1_OUT | MUX_PAD_CTRL(NO_PAD_CTRL), }; static void do_enable_hdmi(struct display_info_t const *dev) @@ -390,55 +397,117 @@ struct display_info_t const displays[] = {{ } } }; size_t display_count = ARRAY_SIZE(displays); -static void setup_display(void) +static void enable_videopll(void) +{ + struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; + s32 timeout = 100000; + + setbits_le32(&ccm->analog_pll_video, BM_ANADIG_PLL_VIDEO_POWERDOWN); + + /* set video pll to 910MHz (24MHz * (37+11/12)) + * video pll post div to 910/4 = 227.5MHz + */ + clrsetbits_le32(&ccm->analog_pll_video, + BM_ANADIG_PLL_VIDEO_DIV_SELECT | + BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT, + BF_ANADIG_PLL_VIDEO_DIV_SELECT(37) | + BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(0)); + + writel(BF_ANADIG_PLL_VIDEO_NUM_A(11), &ccm->analog_pll_video_num); + writel(BF_ANADIG_PLL_VIDEO_DENOM_B(12), &ccm->analog_pll_video_denom); + + clrbits_le32(&ccm->analog_pll_video, BM_ANADIG_PLL_VIDEO_POWERDOWN); + + while (timeout--) + if (readl(&ccm->analog_pll_video) & BM_ANADIG_PLL_VIDEO_LOCK) + break; + + if (timeout < 0) + printf("Warning: video pll lock timeout!\n"); + + clrsetbits_le32(&ccm->analog_pll_video, + BM_ANADIG_PLL_VIDEO_BYPASS, + BM_ANADIG_PLL_VIDEO_ENABLE); +} + +static void setup_display_b850v3(void) { struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; - int reg; - enable_ipu_clock(); + enable_videopll(); + + /* IPU1 D0 clock is 227.5 / 3.5 = 65MHz */ + clrbits_le32(&mxc_ccm->cscmr2, MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV); + imx_setup_hdmi(); - reg = readl(&mxc_ccm->CCGR3); - reg |= MXC_CCM_CCGR3_LDB_DI0_MASK; - writel(reg, &mxc_ccm->CCGR3); - - reg = readl(&mxc_ccm->cs2cdr); - reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK | - MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK); - reg |= (3 << MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET) | - (3 << MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET); - writel(reg, &mxc_ccm->cs2cdr); - - reg = readl(&mxc_ccm->cscmr2); - reg |= (MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV); - writel(reg, &mxc_ccm->cscmr2); - - reg = readl(&mxc_ccm->chsccdr); - reg |= (CHSCCDR_CLK_SEL_LDB_DI0 - << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET); - writel(reg, &mxc_ccm->chsccdr); - - reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES - | IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH - | IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW - | IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG - | IOMUXC_GPR2_DATA_WIDTH_CH1_24BIT - | IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG - | IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT - | IOMUXC_GPR2_LVDS_CH1_MODE_ENABLED_DI0 - | IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0; - writel(reg, &iomux->gpr[2]); - - reg = readl(&iomux->gpr[3]); - reg = (reg & ~(IOMUXC_GPR3_LVDS0_MUX_CTL_MASK | - IOMUXC_GPR3_LVDS1_MUX_CTL_MASK | - IOMUXC_GPR3_HDMI_MUX_CTL_MASK)) - | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0 - << IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET) - | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0 - << IOMUXC_GPR3_LVDS1_MUX_CTL_OFFSET); - writel(reg, &iomux->gpr[3]); + /* Set LDB_DI0 as clock source for IPU_DI0 */ + clrsetbits_le32(&mxc_ccm->chsccdr, + MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK, + (CHSCCDR_CLK_SEL_LDB_DI0 << + MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET)); + + /* Turn on IPU LDB DI0 clocks */ + setbits_le32(&mxc_ccm->CCGR3, MXC_CCM_CCGR3_LDB_DI0_MASK); + + enable_ipu_clock(); + + writel(IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES | + IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_LOW | + IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW | + IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG | + IOMUXC_GPR2_DATA_WIDTH_CH1_24BIT | + IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG | + IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT | + IOMUXC_GPR2_SPLIT_MODE_EN_MASK | + IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0 | + IOMUXC_GPR2_LVDS_CH1_MODE_ENABLED_DI0, + &iomux->gpr[2]); + + clrbits_le32(&iomux->gpr[3], + IOMUXC_GPR3_LVDS0_MUX_CTL_MASK | + IOMUXC_GPR3_LVDS1_MUX_CTL_MASK | + IOMUXC_GPR3_HDMI_MUX_CTL_MASK); +} + +static void setup_display_bx50v3(void) +{ + struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; + struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; + + /* When a reset/reboot is performed the display power needs to be turned + * off for atleast 500ms. The boot time is ~300ms, we need to wait for + * an additional 200ms here. Unfortunately we use external PMIC for + * doing the reset, so can not differentiate between POR vs soft reset + */ + mdelay(200); + + /* IPU1 DI0 clock is 480/7 = 68.5 MHz */ + setbits_le32(&mxc_ccm->cscmr2, MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV); + + /* Set LDB_DI0 as clock source for IPU_DI0 */ + clrsetbits_le32(&mxc_ccm->chsccdr, + MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK, + (CHSCCDR_CLK_SEL_LDB_DI0 << + MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET)); + + /* Turn on IPU LDB DI0 clocks */ + setbits_le32(&mxc_ccm->CCGR3, MXC_CCM_CCGR3_LDB_DI0_MASK); + + enable_ipu_clock(); + + writel(IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES | + IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW | + IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG | + IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT | + IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0, + &iomux->gpr[2]); + + clrsetbits_le32(&iomux->gpr[3], + IOMUXC_GPR3_LVDS0_MUX_CTL_MASK, + (IOMUXC_GPR3_MUX_SRC_IPU1_DI0 << + IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET)); /* backlights off until needed */ imx_iomux_v3_setup_multiple_pads(backlight_pads, @@ -467,6 +536,12 @@ int board_eth_init(bd_t *bis) static iomux_v3_cfg_t const misc_pads[] = { MX6_PAD_KEY_ROW2__GPIO4_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL), + MX6_PAD_EIM_A25__GPIO5_IO02 | MUX_PAD_CTRL(NC_PAD_CTRL), + MX6_PAD_EIM_CS0__GPIO2_IO23 | MUX_PAD_CTRL(NC_PAD_CTRL), + MX6_PAD_EIM_CS1__GPIO2_IO24 | MUX_PAD_CTRL(NC_PAD_CTRL), + MX6_PAD_EIM_OE__GPIO2_IO25 | MUX_PAD_CTRL(NC_PAD_CTRL), + MX6_PAD_EIM_BCLK__GPIO6_IO31 | MUX_PAD_CTRL(NC_PAD_CTRL), + MX6_PAD_GPIO_1__GPIO1_IO01 | MUX_PAD_CTRL(NC_PAD_CTRL), }; #define SUS_S3_OUT IMX_GPIO_NR(4, 11) #define WIFI_EN IMX_GPIO_NR(6, 14) @@ -478,7 +553,14 @@ int board_early_init_f(void) setup_iomux_uart(); - +#if defined(CONFIG_VIDEO_IPUV3) + if (IS_ENABLED(CONFIG_TARGET_GE_B850V3)) + /* Set LDB clock to Video PLL */ + select_ldb_di_clock_source(MXC_PLL5_CLK); + else + /* Set LDB clock to USB PLL */ + select_ldb_di_clock_source(MXC_PLL3_SW_CLK); +#endif return 0; } @@ -487,7 +569,10 @@ int board_init(void) gpio_direction_output(SUS_S3_OUT, 1); gpio_direction_output(WIFI_EN, 1); #if defined(CONFIG_VIDEO_IPUV3) - setup_display(); + if (IS_ENABLED(CONFIG_TARGET_GE_B850V3)) + setup_display_b850v3(); + else + setup_display_bx50v3(); #endif /* address of boot parameters */ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; @@ -520,9 +605,17 @@ int board_late_init(void) * as per specifications from CHI MEI */ mdelay(250); + /* enable backlight PWM 1 */ + pwm_init(0, 0, 0); + + /* duty cycle 5000000ns, period: 5000000ns */ + pwm_config(0, 5000000, 5000000); + /* Backlight Power */ gpio_direction_output(LVDS_BACKLIGHT_GP, 1); + pwm_enable(0); + return 0; } |