1 files changed, 0 insertions, 273 deletions
diff --git a/board/gumstix/duovero/duovero.c b/board/gumstix/duovero/duovero.c
deleted file mode 100644
index 0df03a5a61..0000000000
--- a/board/gumstix/duovero/duovero.c
+++ /dev/null
@@ -1,273 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2013
- * Gumstix Inc. <www.gumstix.com>
- * Maintainer: Ash Charles  <ash@gumstix.com>
- */
-#include <common.h>
-#include <init.h>
-#include <net.h>
-#include <netdev.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/arch/mmc_host_def.h>
-#include <twl6030.h>
-#include <asm/emif.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/gpio.h>
-#include <asm/gpio.h>
-#include <asm/mach-types.h>
-#include <linux/delay.h>
-
-#include "duovero_mux_data.h"
-
-#define WIFI_EN	43
-
-#if defined(CONFIG_CMD_NET)
-#define SMSC_NRESET	45
-static void setup_net_chip(void);
-#endif
-
-#ifdef CONFIG_USB_EHCI_HCD
-#include <usb.h>
-#include <asm/arch/ehci.h>
-#include <asm/ehci-omap.h>
-#endif
-
-DECLARE_GLOBAL_DATA_PTR;
-
-const struct omap_sysinfo sysinfo = {
-	"Board: duovero\n"
-};
-
-struct omap4_scrm_regs *const scrm = (struct omap4_scrm_regs *)0x4a30a000;
-
-/**
- * @brief board_init
- *
- * @return 0
- */
-int board_init(void)
-{
-	gpmc_init();
-
-	gd->bd->bi_arch_number = MACH_TYPE_DUOVERO;
-	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
-
-	return 0;
-}
-
-/**
- * @brief misc_init_r - Configure board specific configurations
- * such as power configurations, ethernet initialization as phase2 of
- * boot sequence
- *
- * @return 0
- */
-int misc_init_r(void)
-{
-	int ret = 0;
-	u8 val;
-
-	/* wifi setup: first enable 32Khz clock from 6030 pmic */
-	val = 0xe1;
-	ret = i2c_write(TWL6030_CHIP_PM, 0xbe, 1, &val, 1);
-	if (ret)
-		printf("Failed to enable 32Khz clock to wifi module\n");
-
-	/* then setup WIFI_EN as an output pin and send reset pulse */
-	if (!gpio_request(WIFI_EN, "")) {
-		gpio_direction_output(WIFI_EN, 0);
-		gpio_set_value(WIFI_EN, 1);
-		udelay(1);
-		gpio_set_value(WIFI_EN, 0);
-		udelay(1);
-		gpio_set_value(WIFI_EN, 1);
-	}
-
-#if defined(CONFIG_CMD_NET)
-	setup_net_chip();
-#endif
-	return 0;
-}
-
-void set_muxconf_regs(void)
-{
-	do_set_mux((*ctrl)->control_padconf_core_base,
-		   core_padconf_array_essential,
-		   sizeof(core_padconf_array_essential) /
-		   sizeof(struct pad_conf_entry));
-
-	do_set_mux((*ctrl)->control_padconf_wkup_base,
-		   wkup_padconf_array_essential,
-		   sizeof(wkup_padconf_array_essential) /
-		   sizeof(struct pad_conf_entry));
-
-	do_set_mux((*ctrl)->control_padconf_core_base,
-		   core_padconf_array_non_essential,
-		   sizeof(core_padconf_array_non_essential) /
-		   sizeof(struct pad_conf_entry));
-
-	do_set_mux((*ctrl)->control_padconf_wkup_base,
-		   wkup_padconf_array_non_essential,
-		   sizeof(wkup_padconf_array_non_essential) /
-		   sizeof(struct pad_conf_entry));
-}
-
-#if defined(CONFIG_MMC)
-int board_mmc_init(bd_t *bis)
-{
-	return omap_mmc_init(0, 0, 0, -1, -1);
-}
-
-#if !defined(CONFIG_SPL_BUILD)
-void board_mmc_power_init(void)
-{
-	twl6030_power_mmc_init(0);
-}
-#endif
-#endif
-
-#if defined(CONFIG_CMD_NET)
-
-#define GPMC_SIZE_16M	0xF
-#define GPMC_BASEADDR_MASK	0x3F
-#define GPMC_CS_ENABLE		0x1
-
-static void enable_gpmc_net_config(const u32 *gpmc_config, const struct gpmc_cs *cs,
-		u32 base, u32 size)
-{
-	writel(0, &cs->config7);
-	sdelay(1000);
-	/* Delay for settling */
-	writel(gpmc_config[0], &cs->config1);
-	writel(gpmc_config[1], &cs->config2);
-	writel(gpmc_config[2], &cs->config3);
-	writel(gpmc_config[3], &cs->config4);
-	writel(gpmc_config[4], &cs->config5);
-	writel(gpmc_config[5], &cs->config6);
-
-	/*
-	 * Enable the config.  size is the CS size and goes in
-	 * bits 11:8.  We set bit 6 to enable this CS and the base
-	 * address goes into bits 5:0.
-	 */
-	writel((size << 8) | (GPMC_CS_ENABLE << 6) |
-				 ((base >> 24) & GPMC_BASEADDR_MASK),
-				 &cs->config7);
-
-	sdelay(2000);
-}
-
-/* GPMC CS configuration for an SMSC LAN9221 ethernet controller */
-#define NET_LAN9221_GPMC_CONFIG1    0x2a001203
-#define NET_LAN9221_GPMC_CONFIG2    0x000a0a02
-#define NET_LAN9221_GPMC_CONFIG3    0x00020200
-#define NET_LAN9221_GPMC_CONFIG4    0x0a030a03
-#define NET_LAN9221_GPMC_CONFIG5    0x000a0a0a
-#define NET_LAN9221_GPMC_CONFIG6    0x8a070707
-#define NET_LAN9221_GPMC_CONFIG7    0x00000f6c
-
-/* GPMC definitions for LAN9221 chips on expansion boards */
-static const u32 gpmc_lan_config[] = {
-	NET_LAN9221_GPMC_CONFIG1,
-	NET_LAN9221_GPMC_CONFIG2,
-	NET_LAN9221_GPMC_CONFIG3,
-	NET_LAN9221_GPMC_CONFIG4,
-	NET_LAN9221_GPMC_CONFIG5,
-	NET_LAN9221_GPMC_CONFIG6,
-	/*CONFIG7- computed as params */
-};
-
-/*
- * Routine: setup_net_chip
- * Description: Setting up the configuration GPMC registers specific to the
- *	      Ethernet hardware.
- */
-static void setup_net_chip(void)
-{
-	enable_gpmc_net_config(gpmc_lan_config, &gpmc_cfg->cs[5], 0x2C000000,
-			      GPMC_SIZE_16M);
-
-	/* Make GPIO SMSC_NRESET as output pin and send reset pulse */
-	if (!gpio_request(SMSC_NRESET, "")) {
-		gpio_direction_output(SMSC_NRESET, 0);
-		gpio_set_value(SMSC_NRESET, 1);
-		udelay(1);
-		gpio_set_value(SMSC_NRESET, 0);
-		udelay(1);
-		gpio_set_value(SMSC_NRESET, 1);
-	}
-}
-#endif
-
-int board_eth_init(bd_t *bis)
-{
-	int rc = 0;
-#ifdef CONFIG_SMC911X
-	rc = smc911x_initialize(0, CONFIG_SMC911X_BASE);
-#endif
-	return rc;
-}
-
-#ifdef CONFIG_USB_EHCI_HCD
-
-static struct omap_usbhs_board_data usbhs_bdata = {
-	.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
-	.port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
-	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-};
-
-int ehci_hcd_init(int index, enum usb_init_type init,
-		struct ehci_hccr **hccr, struct ehci_hcor **hcor)
-{
-	int ret;
-	unsigned int utmi_clk;
-	u32 auxclk, altclksrc;
-
-	/* Now we can enable our port clocks */
-	utmi_clk = readl((void *)CM_L3INIT_HSUSBHOST_CLKCTRL);
-	utmi_clk |= HSUSBHOST_CLKCTRL_CLKSEL_UTMI_P1_MASK;
-	setbits_le32((void *)CM_L3INIT_HSUSBHOST_CLKCTRL, utmi_clk);
-
-	auxclk = readl(&scrm->auxclk3);
-	/* Select sys_clk */
-	auxclk &= ~AUXCLK_SRCSELECT_MASK;
-	auxclk |=  AUXCLK_SRCSELECT_SYS_CLK << AUXCLK_SRCSELECT_SHIFT;
-	/* Set the divisor to 2 */
-	auxclk &= ~AUXCLK_CLKDIV_MASK;
-	auxclk |= AUXCLK_CLKDIV_2 << AUXCLK_CLKDIV_SHIFT;
-	/* Request auxilary clock #3 */
-	auxclk |= AUXCLK_ENABLE_MASK;
-	writel(auxclk, &scrm->auxclk3);
-
-	altclksrc = readl(&scrm->altclksrc);
-
-	/* Activate alternate system clock supplier */
-	altclksrc &= ~ALTCLKSRC_MODE_MASK;
-	altclksrc |= ALTCLKSRC_MODE_ACTIVE;
-
-	/* enable clocks */
-	altclksrc |= ALTCLKSRC_ENABLE_INT_MASK | ALTCLKSRC_ENABLE_EXT_MASK;
-
-	writel(altclksrc, &scrm->altclksrc);
-
-	ret = omap_ehci_hcd_init(index, &usbhs_bdata, hccr, hcor);
-	if (ret < 0)
-		return ret;
-
-	return 0;
-}
-
-int ehci_hcd_stop(int index)
-{
-	return omap_ehci_hcd_stop();
-}
-#endif
-
-/*
- * get_board_rev() - get board revision
- */
-u32 get_board_rev(void)
-{
-	return 0x20;
-}