1 files changed, 0 insertions, 91 deletions
diff --git a/board/miromico/hammerhead/hammerhead.c b/board/miromico/hammerhead/hammerhead.c
deleted file mode 100644
index a0c7d3b323..0000000000
--- a/board/miromico/hammerhead/hammerhead.c
+++ /dev/null
@@ -1,91 +0,0 @@
-/*
- * Copyright (C) 2008 Miromico AG
- *
- * Mostly copied form atmel ATNGW100 sources
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <netdev.h>
-
-#include <asm/io.h>
-#include <asm/sdram.h>
-#include <asm/arch/clk.h>
-#include <asm/arch/hmatrix.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/mmu.h>
-#include <asm/arch/portmux.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-struct mmu_vm_range mmu_vmr_table[CONFIG_SYS_NR_VM_REGIONS] = {
-	{
-		.virt_pgno	= CONFIG_SYS_FLASH_BASE >> MMU_PAGE_SHIFT,
-		.nr_pages	= CONFIG_SYS_FLASH_SIZE >> MMU_PAGE_SHIFT,
-		.phys		= (CONFIG_SYS_FLASH_BASE >> MMU_PAGE_SHIFT)
-					| MMU_VMR_CACHE_NONE,
-	}, {
-		.virt_pgno	= CONFIG_SYS_SDRAM_BASE >> MMU_PAGE_SHIFT,
-		.nr_pages	= EBI_SDRAM_SIZE >> MMU_PAGE_SHIFT,
-		.phys		= (CONFIG_SYS_SDRAM_BASE >> MMU_PAGE_SHIFT)
-					| MMU_VMR_CACHE_WRBACK,
-	},
-};
-
-static const struct sdram_config sdram_config = {
-	.data_bits	= SDRAM_DATA_32BIT,
-	.row_bits	= 13,
-	.col_bits	= 9,
-	.bank_bits	= 2,
-	.cas		= 3,
-	.twr		= 2,
-	.trc		= 7,
-	.trp		= 2,
-	.trcd		= 2,
-	.tras		= 5,
-	.txsr		= 5,
-	/* 7.81 us */
-	.refresh_period	= (781 * (SDRAMC_BUS_HZ / 1000)) / 100000,
-};
-
-#ifdef CONFIG_CMD_NET
-int board_eth_init(bd_t *bis)
-{
-	return macb_eth_initialize(0, (void *)ATMEL_BASE_MACB0,
-		bis->bi_phy_id[0]);
-}
-#endif
-
-int board_early_init_f(void)
-{
-	/* Enable SDRAM in the EBI mux */
-	hmatrix_slave_write(EBI, SFR, HMATRIX_BIT(EBI_SDRAM_ENABLE));
-
-	portmux_enable_ebi(32, 23, 0, PORTMUX_DRIVE_HIGH);
-	sdram_init(uncached(EBI_SDRAM_BASE), &sdram_config);
-
-	portmux_enable_usart1(PORTMUX_DRIVE_MIN);
-
-#if defined(CONFIG_MACB)
-	portmux_enable_macb0(PORTMUX_MACB_MII, PORTMUX_DRIVE_HIGH);
-#endif
-#if defined(CONFIG_MMC)
-	portmux_enable_mmci(0, PORTMUX_MMCI_4BIT, PORTMUX_DRIVE_LOW);
-#endif
-	return 0;
-}
-
-int board_early_init_r(void)
-{
-	gd->bd->bi_phy_id[0] = 0x01;
-	return 0;
-}
-
-int board_postclk_init(void)
-{
-	/* Hammerhead boards uses GCLK3 as 25MHz output to ethernet PHY */
-	gclk_enable_output(3, PORTMUX_DRIVE_LOW);
-	gclk_set_rate(3, GCLK_PARENT_OSC0, 25000000);
-	return 0;
-}