diff options
Diffstat (limited to 'board/mousse/mousse.h')
| -rw-r--r-- | board/mousse/mousse.h | 243 |
1 files changed, 0 insertions, 243 deletions
diff --git a/board/mousse/mousse.h b/board/mousse/mousse.h deleted file mode 100644 index ce8a054175..0000000000 --- a/board/mousse/mousse.h +++ /dev/null @@ -1,243 +0,0 @@ -/* - * MOUSSE/MPC8240 Board definitions. - * For more info, see http://www.vooha.com/ - * - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * (C) Copyright 2001 - * James Dougherty (jfd@cs.stanford.edu) - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __MOUSSE_H -#define __MOUSSE_H - -/* System addresses */ - -#define PCI_SPECIAL_BASE 0xfe000000 -#define PCI_SPECIAL_SIZE 0x01000000 - -/* PORTX Device Addresses for Mousse */ - -#define PORTX_DEV_BASE 0xff000000 -#define PORTX_DEV_SIZE 0x01000000 - -#define ENET_DEV_BASE 0x80000000 - -#define PLD_REG_BASE (PORTX_DEV_BASE | 0xe09000) -#define PLD_REG(off) (*(volatile unsigned char *) \ - (PLD_REG_BASE + (off))) - -#define PLD_REVID_B1 0x7f -#define PLD_REVID_B2 0x01 - -/* MPLD */ -#define SYS_HARD_RESET() { for (;;) PLD_REG(0) = 0; } /* clr 0x80 bit */ -#define SYS_REVID_GET() ((int) PLD_REG(0) & 0x7f) -#define SYS_LED_OFF() (PLD_REG(1) |= 0x80) -#define SYS_LED_ON() (PLD_REG(1) &= ~0x80) -#define SYS_WATCHDOG_IRQ3() (PLD_REG(2) |= 0x80) -#define SYS_WATCHDOG_RESET() (PLD_REG(2) &= ~0x80) -#define SYS_TOD_PROTECT() (PLD_REG(3) |= 0x80) -#define SYS_TOD_UNPROTECT() (PLD_REG(3) &= ~0x80) - -/* SGS M48T59Y */ -#define TOD_BASE (PORTX_DEV_BASE | 0xe0a000) -#define TOD_REG_BASE (TOD_BASE | 0x1ff0) -#define TOD_NVRAM_BASE TOD_BASE -#define TOD_NVRAM_SIZE 0x1ff0 -#define TOD_NVRAM_LIMIT (TOD_NVRAM_BASE + TOD_NVRAM_SIZE) - -/* NS16552 SIO */ -#define SERIAL_BASE(_x) (PORTX_DEV_BASE | 0xe08000 | ((_x) ? 0 : 0x80)) -#define N_SIO_CHANNELS 2 -#define N_COM_PORTS N_SIO_CHANNELS - -/* - * On-board Dec21143 PCI Ethernet - * Note: The PCI MBAR chosen here was used from MPC8240UM which states - * that PCI memory is at: 0x80000 - 0xFDFFFFFF, if AMBOR[CPU_FD_ALIAS] - * is set, then PCI memory maps 1-1 with this address range in the - * correct byte order. - */ -#define PCI_ENET_IOADDR 0x80000000 -#define PCI_ENET_MEMADDR 0x80000000 - -/* - * Flash Memory Layout - * - * 2 MB Flash Bank 0 runs in 8-bit mode. In Flash Bank 0, the 32 kB - * sector SA3 is obscured by the 32 kB serial/TOD access space, and - * the 64 kB sectors SA19-SA26 are obscured by the 512 kB PLCC - * containing the fixed boot ROM. (If the 512 kB PLCC is - * deconfigured by jumper, this window to Flash Bank 0 becomes - * visible, but it still contains the fixed boot code and should be - * considered read-only). Flash Bank 0 sectors SA0 (16 kB), SA1 (8 - * kB), and SA2 (8 kB) are currently unused. - * - * 2 MB Flash Bank 1 runs in 16-bit mode. Flash Bank 1 is fully - * usable, but it's a 16-bit wide device on a 64-bit bus. Therefore - * 16-bit words only exist at addresses that are multiples of 8. All - * PROM data and control addresses must be multiplied by 8. - * - * See flashMap.c for description of flash filesystem layout. - */ - -/* - * FLASH memory address space: 8-bit wide FLASH memory spaces. - */ -#define FLASH0_SEG0_START 0xffe00000 /* Baby 32Kb segment */ -#define FLASH0_SEG0_END 0xffe07fff /* 16 kB + 8 kB + 8 kB */ -#define FLASH0_SEG0_SIZE 0x00008000 /* (sectors SA0-SA2) */ - -#define FLASH0_SEG1_START 0xffe10000 /* 1MB - 64Kb FLASH0 seg */ -#define FLASH0_SEG1_END 0xffefffff /* 960 kB */ -#define FLASH0_SEG1_SIZE 0x000f0000 - -#define FLASH0_SEG2_START 0xfff00000 /* Boot Loader stored here */ -#define FLASH0_SEG2_END 0xfff7ffff /* 512 kB FLASH0/PLCC seg */ -#define FLASH0_SEG2_SIZE 0x00080000 - -#define FLASH0_SEG3_START 0xfff80000 /* 512 kB FLASH0 seg */ -#define FLASH0_SEG3_END 0xffffffff -#define FLASH0_SEG3_SIZE 0x00080000 - -/* Where Kahlua starts */ -#define FLASH_RESET_VECT 0xfff00100 - -/* - * CHRP / PREP (MAP A/B) definitions. - */ - -#define PREP_REG_ADDR 0x80000cf8 /* MPC107 Config, Map A */ -#define PREP_REG_DATA 0x80000cfc /* MPC107 Config, Map A */ -/* MPC107 (MPC8240 internal EUMBBAR mapped) */ -#define CHRP_REG_ADDR 0xfec00000 /* MPC106 Config, Map B */ -#define CHRP_REG_DATA 0xfee00000 /* MPC106 Config, Map B */ - -/* - * Mousse PCI IDSEL Assignments (Device Number) - */ -#define MOUSSE_IDSEL_ENET 13 /* On-board 21143 Ethernet */ -#define MOUSSE_IDSEL_LPCI 14 /* On-board PCI slot */ -#define MOUSSE_IDSEL_82371 15 /* That other thing */ -#define MOUSSE_IDSEL_CPCI2 31 /* CPCI slot 2 */ -#define MOUSSE_IDSEL_CPCI3 30 /* CPCI slot 3 */ -#define MOUSSE_IDSEL_CPCI4 29 /* CPCI slot 4 */ -#define MOUSSE_IDSEL_CPCI5 28 /* CPCI slot 5 */ -#define MOUSSE_IDSEL_CPCI6 27 /* CPCI slot 6 */ - -/* - * Mousse Interrupt Mapping: - * - * IRQ1 Enet (intA|intB|intC|intD) - * IRQ2 CPCI intA (See below) - * IRQ3 Local PCI slot intA|intB|intC|intD - * IRQ4 COM1 Serial port (Actually higher addressed port on duart) - * - * PCI Interrupt Mapping in CPCI chassis: - * - * | CPCI Slot - * | 1 (CPU) 2 3 4 5 6 - * -----------+--------+-------+-------+-------+-------+-------+ - * intA | X X X - * intB | X X X - * intC | X X X - * intD | X X X - */ - - -#define EPIC_VECTOR_EXT0 0 -#define EPIC_VECTOR_EXT1 1 -#define EPIC_VECTOR_EXT2 2 -#define EPIC_VECTOR_EXT3 3 -#define EPIC_VECTOR_EXT4 4 -#define EPIC_VECTOR_TM0 16 -#define EPIC_VECTOR_TM1 17 -#define EPIC_VECTOR_TM2 18 -#define EPIC_VECTOR_TM3 19 -#define EPIC_VECTOR_I2C 20 -#define EPIC_VECTOR_DMA0 21 -#define EPIC_VECTOR_DMA1 22 -#define EPIC_VECTOR_I2O 23 - - -#define INT_VEC_IRQ0 0 -#define INT_NUM_IRQ0 INT_VEC_IRQ0 -#define MOUSSE_IRQ_ENET EPIC_VECTOR_EXT1 /* Hardwired */ -#define MOUSSE_IRQ_CPCI EPIC_VECTOR_EXT2 /* Hardwired */ -#define MOUSSE_IRQ_LPCI EPIC_VECTOR_EXT3 /* Hardwired */ -#define MOUSSE_IRQ_DUART EPIC_VECTOR_EXT4 /* Hardwired */ - -/* Onboard DEC 21143 Ethernet */ -#define PCI_ENET_MEMADDR 0x80000000 -#define PCI_ENET_IOADDR 0x80000000 - -/* Some other PCI device */ -#define PCI_SLOT_MEMADDR 0x81000000 -#define PCI_SLOT_IOADDR 0x81000000 - -/* Promise ATA66 PCI Device (ATA controller) */ -#define PROMISE_MBAR0 0xa0000000 -#define PROMISE_MBAR1 (PROMISE_MBAR0 + 0x1000) -#define PROMISE_MBAR2 (PROMISE_MBAR0 + 0x2000) -#define PROMISE_MBAR3 (PROMISE_MBAR0 + 0x3000) -#define PROMISE_MBAR4 (PROMISE_MBAR0 + 0x4000) -#define PROMISE_MBAR5 (PROMISE_MBAR0 + 0x5000) - -/* ATA/66 Controller offsets */ -#define CONFIG_SYS_ATA_BASE_ADDR PROMISE_MBAR0 -#define CONFIG_SYS_IDE_MAXBUS 2 /* ide0/ide1 */ -#define CONFIG_SYS_IDE_MAXDEVICE 2 /* 2 drives per controller */ -#define CONFIG_SYS_ATA_IDE0_OFFSET 0 -#define CONFIG_SYS_ATA_IDE1_OFFSET 0x3000 -/* - * Definitions for accessing IDE controller registers - */ -#define CONFIG_SYS_ATA_DATA_OFFSET 0 -#define CONFIG_SYS_ATA_REG_OFFSET 0 -#define CONFIG_SYS_ATA_ALT_OFFSET (0x1000) - -/* - * The constants ROM_TEXT_ADRS, ROM_SIZE, RAM_HIGH_ADRS, and RAM_LOW_ADRS - * are defined in config.h and Makefile. - * All definitions for these constants must be identical. - */ -#define ROM_BASE_ADRS 0xfff00000 /* base address of ROM */ -#define ROM_TEXT_ADRS (ROM_BASE_ADRS+0x0100) /* with PC & SP */ -#define ROM_WARM_ADRS (ROM_TEXT_ADRS+0x0004) /* warm reboot entry */ -#define ROM_SIZE 0x00080000 /* 512KB ROM space */ -#define RAM_LOW_ADRS 0x00010000 /* RAM address for vxWorks */ -#define RAM_HIGH_ADRS 0x00c00000 /* RAM address for bootrom */ - -/* - * NVRAM configuration - * NVRAM is implemented via the SGS Thomson M48T59Y - * 64Kbit (8Kbx8) Timekeeper SRAM. - * This 8KB NVRAM also has a TOD. See m48t59y.{h,c} for more information. - */ - -#define NV_RAM_ADRS TOD_NVRAM_BASE -#define NV_RAM_INTRVL 1 -#define NV_RAM_WR_ENBL SYS_TOD_UNPROTECT() -#define NV_RAM_WR_DSBL SYS_TOD_PROTECT() - -#define NV_OFF_BOOT0 0x0000 /* Boot string 0 (256b) */ -#define NV_OFF_BOOT1 0x0100 /* Boot string 1 (256b) */ -#define NV_OFF_BOOT2 0x0200 /* Boot string 2 (256b)*/ -#define NV_OFF_MACADDR 0x0400 /* 21143 MAC address (6b) */ -#define NV_OFF_ACTIVEBOOT 0x0406 /* Active boot string, 0 to 2 (1b) */ -#define NV_OFF_UNUSED1 0x0407 /* Unused (1b) */ -#define NV_OFF_BINDFIX 0x0408 /* See sysLib.c:sysBindFix() (1b) */ -#define NV_OFF_UNUSED2 0x0409 /* Unused (7b) */ -#define NV_OFF_TIMEZONE 0x0410 /* TIMEZONE env var (64b) */ -#define NV_OFF_VXWORKS_END 0x07FF /* 2047 VxWorks Total */ -#define NV_OFF_U_BOOT 0x0800 /* 2048 U-Boot boot-loader */ -#define NV_OFF_U_BOOT_ADDR (TOD_BASE + NV_OFF_U_BOOT) /* sysaddr*/ -#define NV_U_BOOT_ENV_SIZE 2048 /* 2K - U-Boot Total */ -#define NV_OFF__next_free (NV_U_BOOT_ENVSIZE +1) -#define NV_RAM_SIZE 8176 /* NVRAM End */ - -#endif /* __MOUSSE_H */ |