diff options
Diffstat (limited to 'board/mx31ads/lowlevel_init.S')
| -rw-r--r-- | board/mx31ads/lowlevel_init.S | 281 |
1 files changed, 281 insertions, 0 deletions
diff --git a/board/mx31ads/lowlevel_init.S b/board/mx31ads/lowlevel_init.S new file mode 100644 index 0000000000..099a7ca81b --- /dev/null +++ b/board/mx31ads/lowlevel_init.S @@ -0,0 +1,281 @@ +/* + * Copyright (C) 2008, Guennadi Liakhovetski <lg@denx.de> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <asm/arch/mx31-regs.h> + +.macro REG reg, val + ldr r2, =\reg + ldr r3, =\val + str r3, [r2] +.endm + +.macro REG8 reg, val + ldr r2, =\reg + ldr r3, =\val + strb r3, [r2] +.endm + +.macro DELAY loops + ldr r2, =\loops +1: + subs r2, r2, #1 + nop + bcs 1b +.endm + +/* RedBoot: AIPS setup - Only setup MPROTx registers. + * The PACR default values are good.*/ +.macro init_aips + /* + * Set all MPROTx to be non-bufferable, trusted for R/W, + * not forced to user-mode. + */ + ldr r0, =0x43F00000 + ldr r1, =0x77777777 + str r1, [r0, #0x00] + str r1, [r0, #0x04] + ldr r0, =0x53F00000 + str r1, [r0, #0x00] + str r1, [r0, #0x04] + + /* + * Clear the on and off peripheral modules Supervisor Protect bit + * for SDMA to access them. Did not change the AIPS control registers + * (offset 0x20) access type + */ + ldr r0, =0x43F00000 + ldr r1, =0x0 + str r1, [r0, #0x40] + str r1, [r0, #0x44] + str r1, [r0, #0x48] + str r1, [r0, #0x4C] + ldr r1, [r0, #0x50] + and r1, r1, #0x00FFFFFF + str r1, [r0, #0x50] + + ldr r0, =0x53F00000 + ldr r1, =0x0 + str r1, [r0, #0x40] + str r1, [r0, #0x44] + str r1, [r0, #0x48] + str r1, [r0, #0x4C] + ldr r1, [r0, #0x50] + and r1, r1, #0x00FFFFFF + str r1, [r0, #0x50] +.endm /* init_aips */ + +/* RedBoot: MAX (Multi-Layer AHB Crossbar Switch) setup */ +.macro init_max + ldr r0, =0x43F04000 + /* MPR - priority is M4 > M2 > M3 > M5 > M0 > M1 */ + ldr r1, =0x00302154 + str r1, [r0, #0x000] /* for S0 */ + str r1, [r0, #0x100] /* for S1 */ + str r1, [r0, #0x200] /* for S2 */ + str r1, [r0, #0x300] /* for S3 */ + str r1, [r0, #0x400] /* for S4 */ + /* SGPCR - always park on last master */ + ldr r1, =0x10 + str r1, [r0, #0x010] /* for S0 */ + str r1, [r0, #0x110] /* for S1 */ + str r1, [r0, #0x210] /* for S2 */ + str r1, [r0, #0x310] /* for S3 */ + str r1, [r0, #0x410] /* for S4 */ + /* MGPCR - restore default values */ + ldr r1, =0x0 + str r1, [r0, #0x800] /* for M0 */ + str r1, [r0, #0x900] /* for M1 */ + str r1, [r0, #0xA00] /* for M2 */ + str r1, [r0, #0xB00] /* for M3 */ + str r1, [r0, #0xC00] /* for M4 */ + str r1, [r0, #0xD00] /* for M5 */ +.endm /* init_max */ + +/* RedBoot: M3IF setup */ +.macro init_m3if + /* Configure M3IF registers */ + ldr r1, =0xB8003000 + /* + * M3IF Control Register (M3IFCTL) + * MRRP[0] = L2CC0 not on priority list (0 << 0) = 0x00000000 + * MRRP[1] = L2CC1 not on priority list (0 << 0) = 0x00000000 + * MRRP[2] = MBX not on priority list (0 << 0) = 0x00000000 + * MRRP[3] = MAX1 not on priority list (0 << 0) = 0x00000000 + * MRRP[4] = SDMA not on priority list (0 << 0) = 0x00000000 + * MRRP[5] = MPEG4 not on priority list (0 << 0) = 0x00000000 + * MRRP[6] = IPU1 on priority list (1 << 6) = 0x00000040 + * MRRP[7] = IPU2 not on priority list (0 << 0) = 0x00000000 + * ------------ + * 0x00000040 + */ + ldr r0, =0x00000040 + str r0, [r1] /* M3IF control reg */ +.endm /* init_m3if */ + +/* RedBoot: To support 133MHz DDR */ +.macro init_drive_strength + /* + * Disable maximum drive strength SDRAM/DDR lines by clearing DSE1 bits + * in SW_PAD_CTL registers + */ + + /* SDCLK */ + ldr r1, =0x43FAC200 + ldr r0, [r1, #0x6C] + bic r0, r0, #(1 << 12) + str r0, [r1, #0x6C] + + /* CAS */ + ldr r0, [r1, #0x70] + bic r0, r0, #(1 << 22) + str r0, [r1, #0x70] + + /* RAS */ + ldr r0, [r1, #0x74] + bic r0, r0, #(1 << 2) + str r0, [r1, #0x74] + + /* CS2 (CSD0) */ + ldr r0, [r1, #0x7C] + bic r0, r0, #(1 << 22) + str r0, [r1, #0x7C] + + /* DQM3 */ + ldr r0, [r1, #0x84] + bic r0, r0, #(1 << 22) + str r0, [r1, #0x84] + + /* DQM2, DQM1, DQM0, SD31-SD0, A25-A0, MA10 (0x288..0x2DC) */ + ldr r2, =22 /* (0x2E0 - 0x288) / 4 = 22 */ +pad_loop: + ldr r0, [r1, #0x88] + bic r0, r0, #(1 << 22) + bic r0, r0, #(1 << 12) + bic r0, r0, #(1 << 2) + str r0, [r1, #0x88] + add r1, r1, #4 + subs r2, r2, #0x1 + bne pad_loop +.endm /* init_drive_strength */ + +/* CPLD on CS4 setup */ +.macro init_cs4 + ldr r0, =WEIM_BASE + ldr r1, =0x0000D843 + str r1, [r0, #0x40] + ldr r1, =0x22252521 + str r1, [r0, #0x44] + ldr r1, =0x22220A00 + str r1, [r0, #0x48] +.endm /* init_cs4 */ + +.globl lowlevel_init +lowlevel_init: + + /* Redboot initializes very early AIPS, what for? + * Then it also initializes Multi-Layer AHB Crossbar Switch, + * M3IF */ + /* Also setup the Peripheral Port Remap register inside the core */ + ldr r0, =0x40000015 /* start from AIPS 2GB region */ + mcr p15, 0, r0, c15, c2, 4 + + init_aips + + init_max + + init_m3if + + init_drive_strength + + init_cs4 + + /* Image Processing Unit: */ + /* Too early to switch display on? */ + REG IPU_CONF, IPU_CONF_DI_EN /* Switch on Display Interface */ + /* Clock Control Module: */ + REG CCM_CCMR, 0x074B0BF5 /* Use CKIH, MCU PLL off */ + + DELAY 0x40000 + + REG CCM_CCMR, 0x074B0BF5 | CCMR_MPE /* MCU PLL on */ + REG CCM_CCMR, (0x074B0BF5 | CCMR_MPE) & ~CCMR_MDS /* Switch to MCU PLL */ + + /* PBC CPLD on CS4 */ + mov r1, #CS4_BASE + ldrh r1, [r1, #0x2] + /* Is 27MHz switch set? */ + ands r1, r1, #0x16 + + /* 532-133-66.5 */ + ldr r0, =CCM_BASE + ldr r1, =0xFF871D58 + /* PDR0 */ + str r1, [r0, #0x4] + ldreq r1, MPCTL_PARAM_532 + ldrne r1, MPCTL_PARAM_532_27 + /* MPCTL */ + str r1, [r0, #0x10] + + /* Set UPLL=240MHz, USB=60MHz */ + ldr r1, =0x49FCFE7F + /* PDR1 */ + str r1, [r0, #0x8] + ldreq r1, UPCTL_PARAM_240 + ldrne r1, UPCTL_PARAM_240_27 + /* UPCTL */ + str r1, [r0, #0x14] + /* default CLKO to 1/8 of the ARM core */ + mov r1, #0x000002C0 + add r1, r1, #0x00000006 + /* COSR */ + str r1, [r0, #0x1c] + + /* RedBoot sets 0x1ff, 7, 3, 5, 1, 3, 0 */ +/* REG CCM_PDR0, PDR0_CSI_PODF(0x1ff) | PDR0_PER_PODF(7) | PDR0_HSP_PODF(2) | PDR0_NFC_PODF(6) | PDR0_IPG_PODF(1) | PDR0_MAX_PODF(2) | PDR0_MCU_PODF(0)*/ + + /* Redboot: 0, 51, 10, 12 / 0, 14, 9, 13 */ +/* REG CCM_MPCTL, PLL_PD(0) | PLL_MFD(0x33) | PLL_MFI(7) | PLL_MFN(0x23)*/ + /* Default: 1, 4, 12, 1 */ + REG CCM_SPCTL, PLL_PD(1) | PLL_MFD(4) | PLL_MFI(12) | PLL_MFN(1) + + /* B8xxxxxx - NAND, 8xxxxxxx - CSD0 RAM */ + REG 0xB8001010, 0x00000004 + REG 0xB8001004, 0x006ac73a + REG 0xB8001000, 0x92100000 + REG 0x80000f00, 0x12344321 + REG 0xB8001000, 0xa2100000 + REG 0x80000000, 0x12344321 + REG 0x80000000, 0x12344321 + REG 0xB8001000, 0xb2100000 + REG8 0x80000033, 0xda + REG8 0x81000000, 0xff + REG 0xB8001000, 0x82226080 + REG 0x80000000, 0xDEADBEEF + REG 0xB8001010, 0x0000000c + + mov pc, lr + +MPCTL_PARAM_532: + .word (((1-1) << 26) + ((52-1) << 16) + (10 << 10) + (12 << 0)) +MPCTL_PARAM_532_27: + .word (((1-1) << 26) + ((15-1) << 16) + (9 << 10) + (13 << 0)) +UPCTL_PARAM_240: + .word (((2-1) << 26) + ((13-1) << 16) + (9 << 10) + (3 << 0)) +UPCTL_PARAM_240_27: + .word (((2-1) << 26) + ((9 -1) << 16) + (8 << 10) + (8 << 0)) |