diff options
Diffstat (limited to 'board/st-ericsson/u8500/u8500_href.c')
| -rw-r--r-- | board/st-ericsson/u8500/u8500_href.c | 100 |
1 files changed, 21 insertions, 79 deletions
diff --git a/board/st-ericsson/u8500/u8500_href.c b/board/st-ericsson/u8500/u8500_href.c index 5f85fdcbfc..ec559e33e0 100644 --- a/board/st-ericsson/u8500/u8500_href.c +++ b/board/st-ericsson/u8500/u8500_href.c @@ -18,6 +18,7 @@ #include <config.h> #include <common.h> +#include <malloc.h> #include <i2c.h> #include <asm/types.h> #include <asm/io.h> @@ -26,8 +27,8 @@ #include <asm/arch/gpio.h> #include <asm/arch/hardware.h> #include <asm/arch/sys_proto.h> +#include <asm/arch/prcmu.h> #ifdef CONFIG_MMC -#include "prcmu-fw.h" #include "../../../drivers/mmc/arm_pl180_mmci.h" #endif @@ -42,7 +43,6 @@ * SGA: Smart Graphic accelerator * B2R2: Graphic blitter */ -#define PRCMU_BASE CFG_PRCMU_BASE /* 0x80157000 for U8500 */ #define PRCM_ARMCLKFIX_MGT_REG (PRCMU_BASE + 0x000) #define PRCM_ACLK_MGT_REG (PRCMU_BASE + 0x004) #define PRCM_SVAMMDSPCLK_MGT_REG (PRCMU_BASE + 0x008) @@ -139,18 +139,6 @@ void show_boot_progress(int progress) } #endif -static unsigned int read_asicid(void) -{ - unsigned int *address = (void *)U8500_BOOTROM_BASE - + U8500_BOOTROM_ASIC_ID_OFFSET; - return readl(address); -} - -int cpu_is_u8500v11(void) -{ - return read_asicid() == 0x008500A1; -} - /* * Miscellaneous platform dependent initialisations */ @@ -227,67 +215,6 @@ unsigned int addr_vall_arr[] = { }; #ifdef CONFIG_BOARD_LATE_INIT -#ifdef CONFIG_MMC - -#define LDO_VAUX3_MASK 0x3 -#define LDO_VAUX3_ENABLE 0x1 -#define VAUX3_VOLTAGE_2_9V 0xd - -#define AB8500_REGU_CTRL2 0x4 -#define AB8500_REGU_VRF1VAUX3_REGU_REG 0x040A -#define AB8500_REGU_VRF1VAUX3_SEL_REG 0x0421 - -static int hrefplus_mmc_power_init(void) -{ - int ret; - int val; - - if (!cpu_is_u8500v11()) - return 0; - - /* - * On v1.1 HREF boards (HREF+), Vaux3 needs to be enabled for the SD - * card to work. This is done by enabling the regulators in the AB8500 - * via PRCMU I2C transactions. - * - * This code is derived from the handling of AB8500_LDO_VAUX3 in - * ab8500_ldo_enable() and ab8500_ldo_disable() in Linux. - * - * Turn off and delay is required to have it work across soft reboots. - */ - - ret = prcmu_i2c_read(AB8500_REGU_CTRL2, AB8500_REGU_VRF1VAUX3_REGU_REG); - if (ret < 0) - goto out; - - val = ret; - - /* Turn off */ - ret = prcmu_i2c_write(AB8500_REGU_CTRL2, AB8500_REGU_VRF1VAUX3_REGU_REG, - val & ~LDO_VAUX3_MASK); - if (ret < 0) - goto out; - - udelay(10 * 1000); - - /* Set the voltage to 2.9V */ - ret = prcmu_i2c_write(AB8500_REGU_CTRL2, - AB8500_REGU_VRF1VAUX3_SEL_REG, - VAUX3_VOLTAGE_2_9V); - if (ret < 0) - goto out; - - val = val & ~LDO_VAUX3_MASK; - val = val | LDO_VAUX3_ENABLE; - - /* Turn on the supply */ - ret = prcmu_i2c_write(AB8500_REGU_CTRL2, - AB8500_REGU_VRF1VAUX3_REGU_REG, val); - -out: - return ret; -} -#endif /* * called after all initialisation were done, but before the generic * mmc_initialize(). @@ -314,7 +241,7 @@ int board_late_init(void) setenv("board_id", "1"); } #ifdef CONFIG_MMC - hrefplus_mmc_power_init(); + u8500_mmc_power_init(); /* * config extended GPIO pins for level shifter and @@ -448,12 +375,27 @@ static int u8500_mmci_board_init(void) int board_mmc_init(bd_t *bd) { + struct pl180_mmc_host *host; + if (u8500_mmci_board_init()) return -ENODEV; - if (arm_pl180_mmci_init()) - return -ENODEV; - return 0; + host = malloc(sizeof(struct pl180_mmc_host)); + if (!host) + return -ENOMEM; + memset(host, 0, sizeof(*host)); + + strcpy(host->name, "MMC"); + host->base = (struct sdi_registers *)CONFIG_ARM_PL180_MMCI_BASE; + host->pwr_init = INIT_PWR; + host->clkdiv_init = SDI_CLKCR_CLKDIV_INIT_V1 | SDI_CLKCR_CLKEN; + host->voltages = VOLTAGE_WINDOW_MMC; + host->caps = 0; + host->clock_in = ARM_MCLK; + host->clock_min = ARM_MCLK / (2 * (SDI_CLKCR_CLKDIV_INIT_V1 + 1)); + host->clock_max = CONFIG_ARM_PL180_MMCI_CLOCK_FREQ; + + return arm_pl180_mmci_init(host); } #endif |