diff options
Diffstat (limited to 'board/technexion/pico-imx6ul/pico-imx6ul.c')
| -rw-r--r-- | board/technexion/pico-imx6ul/pico-imx6ul.c | 96 |
1 files changed, 15 insertions, 81 deletions
diff --git a/board/technexion/pico-imx6ul/pico-imx6ul.c b/board/technexion/pico-imx6ul/pico-imx6ul.c index 8c76778276..95b482a602 100644 --- a/board/technexion/pico-imx6ul/pico-imx6ul.c +++ b/board/technexion/pico-imx6ul/pico-imx6ul.c @@ -13,13 +13,10 @@ #include <asm/arch/sys_proto.h> #include <asm/gpio.h> #include <asm/mach-imx/iomux-v3.h> -#include <asm/mach-imx/mxc_i2c.h> #include <asm/io.h> #include <common.h> #include <miiphy.h> #include <netdev.h> -#include <fsl_esdhc.h> -#include <i2c.h> #include <linux/sizes.h> #include <usb.h> #include <power/pmic.h> @@ -32,15 +29,6 @@ DECLARE_GLOBAL_DATA_PTR; PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) -#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ - PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \ - PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) - -#define I2C_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ - PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ - PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ - PAD_CTL_ODE) - #define OTG_ID_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | \ PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) @@ -56,23 +44,6 @@ DECLARE_GLOBAL_DATA_PTR; #define RMII_PHY_RESET IMX_GPIO_NR(1, 28) -#ifdef CONFIG_SYS_I2C_MXC -#define PC MUX_PAD_CTRL(I2C_PAD_CTRL) -/* I2C2 for PMIC */ -struct i2c_pads_info i2c_pad_info1 = { - .scl = { - .i2c_mode = MX6_PAD_GPIO1_IO02__I2C1_SCL | PC, - .gpio_mode = MX6_PAD_GPIO1_IO02__GPIO1_IO02 | PC, - .gp = IMX_GPIO_NR(1, 2), - }, - .sda = { - .i2c_mode = MX6_PAD_GPIO1_IO03__I2C1_SDA | PC, - .gpio_mode = MX6_PAD_GPIO1_IO03__GPIO1_IO03 | PC, - .gp = IMX_GPIO_NR(1, 3), - }, -}; -#endif - static iomux_v3_cfg_t const fec_pads[] = { MX6_PAD_ENET1_TX_EN__ENET2_MDC | MUX_PAD_CTRL(MDIO_PAD_CTRL), MX6_PAD_ENET1_TX_DATA1__ENET2_MDIO | MUX_PAD_CTRL(MDIO_PAD_CTRL), @@ -96,6 +67,7 @@ int board_eth_init(bd_t *bis) { setup_iomux_fec(); + gpio_request(RMII_PHY_RESET, "enet_phy_reset"); gpio_direction_output(RMII_PHY_RESET, 0); /* * According to KSZ8081MNX-RNB manual: @@ -155,19 +127,6 @@ static iomux_v3_cfg_t const uart6_pads[] = { MX6_PAD_CSI_PIXCLK__UART6_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL), }; -static iomux_v3_cfg_t const usdhc1_pads[] = { - MX6_PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD1_DATA0__USDHC1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD1_DATA1__USDHC1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD1_DATA2__USDHC1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD1_DATA3__USDHC1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_NAND_READY_B__USDHC1_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_NAND_CE0_B__USDHC1_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_NAND_CE1_B__USDHC1_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_NAND_CLE__USDHC1_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), -}; - #define USB_OTHERREGS_OFFSET 0x800 #define UCTRL_PWR_POL (1 << 9) @@ -185,22 +144,6 @@ static void setup_usb(void) imx_iomux_v3_setup_multiple_pads(usb_otg_pad, ARRAY_SIZE(usb_otg_pad)); } -static struct fsl_esdhc_cfg usdhc_cfg[1] = { - {USDHC1_BASE_ADDR}, -}; - -int board_mmc_getcd(struct mmc *mmc) -{ - return 1; -} - -int board_mmc_init(bd_t *bis) -{ - imx_iomux_v3_setup_multiple_pads(usdhc1_pads, ARRAY_SIZE(usdhc1_pads)); - usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK); - return fsl_esdhc_initialize(bis, &usdhc_cfg[0]); -} - int board_early_init_f(void) { setup_iomux_uart(); @@ -208,38 +151,33 @@ int board_early_init_f(void) return 0; } -#ifdef CONFIG_POWER -#define I2C_PMIC 0 -static struct pmic *pfuze; +#ifdef CONFIG_DM_PMIC int power_init_board(void) { - int ret; - unsigned int reg, rev_id; + struct udevice *dev; + int ret, dev_id, rev_id; - ret = power_pfuze3000_init(I2C_PMIC); - if (ret) + ret = pmic_get("pfuze3000", &dev); + if (ret == -ENODEV) + return 0; + if (ret != 0) return ret; - pfuze = pmic_get("PFUZE3000"); - ret = pmic_probe(pfuze); - if (ret) - return ret; - - pmic_reg_read(pfuze, PFUZE3000_DEVICEID, ®); - pmic_reg_read(pfuze, PFUZE3000_REVID, &rev_id); - printf("PMIC: PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n", reg, rev_id); + dev_id = pmic_reg_read(dev, PFUZE3000_DEVICEID); + rev_id = pmic_reg_read(dev, PFUZE3000_REVID); + printf("PMIC: PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n", dev_id, rev_id); /* disable Low Power Mode during standby mode */ - pmic_reg_write(pfuze, PFUZE3000_LDOGCTL, 0x1); + pmic_reg_write(dev, PFUZE3000_LDOGCTL, 0x1); /* SW1B step ramp up time from 2us to 4us/25mV */ - pmic_reg_write(pfuze, PFUZE3000_SW1BCONF, 0x40); + pmic_reg_write(dev, PFUZE3000_SW1BCONF, 0x40); /* SW1B mode to APS/PFM */ - pmic_reg_write(pfuze, PFUZE3000_SW1BMODE, 0xc); + pmic_reg_write(dev, PFUZE3000_SW1BMODE, 0xc); /* SW1B standby voltage set to 0.975V */ - pmic_reg_write(pfuze, PFUZE3000_SW1BSTBY, 0xb); + pmic_reg_write(dev, PFUZE3000_SW1BSTBY, 0xb); return 0; } @@ -274,10 +212,6 @@ int board_init(void) /* Address of boot parameters */ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; - #ifdef CONFIG_SYS_I2C_MXC - setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1); - #endif - setup_fec(); setup_usb(); |